Scribd
Upload
160 views4 pages

SM Caterpillar Cat 320E LRR Excavator PNL00001

This document provides instructions for installing the vibration damper and pulley on an excavator engine. It lists the required tools and provides illustrations of the assembly. The procedure involves cleaning and inspecting parts, placing the crankshaft adapter on supports, installing the pulley and damper using guide studs, and tightening bolts to specified torques. A friction shim may also need to be installed between the pulley and front cover, and new front seal. Guide studs are used to align parts before final installation and torqueing of screws.

Uploaded by

Dariusz Gumiński
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
160 views4 pages

SM Caterpillar Cat 320E LRR Excavator PNL00001

This document provides instructions for installing the vibration damper and pulley on an excavator engine. It lists the required tools and provides illustrations of the assembly. The procedure involves cleaning and inspecting parts, placing the crankshaft adapter on supports, installing the pulley and damper using guide studs, and tightening bolts to specified torques. A friction shim may also need to be installed between the pulley and front cover, and new front seal. Guide studs are used to align parts before final installation and torqueing of screws.

Uploaded by

Dariusz Gumiński
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

w 1/4(W)

Product: EXCAVATOR
Model: 320E LRR EXCAVATOR PNL
Configuration: 320E LRR Excavator PNL00001-UP (MACHINE) POWERED BY C6.6 Engine

Disassembly and Assembly


C6.6 Engines for Caterpillar Built Machines
Media Number -KENR9249-07 Publication Date -01/09/2015 Date Updated -19/06/2017

i05909542

Vibration Damper and Pulley - Install


SMCS - 1205-012

Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
Guide Stud
A - 1
M14 x1.5 by 100 mm
B 227-4393 E18 Torx Socket 1
C 8T-3052 Degree Wheel 1
Guide Stud
D - 2
M12 x1.75 by 50 mm

NOTICE

Do not lubricate the crankshaft front seal. The crankshaft front seal
must be installed dry.

NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/11/16
w 2/4(W)

Illustration 1 g02368018

1. Ensure that the crankshaft adapter and the front of the crankshaft are clean and free from
damage.

2. Inspect vibration damper (6) for damage. If necessary, replace the vibration damper.

3. If necessary, follow Step 3.a through Step 3.e in order to install vibration damper,
crankshaft pulley to crankshaft adapter.

a. Place crankshaft adapter (4) onto a suitable support.

b. Install Tooling (D) crankshaft adapter (4) .

c. Install crankshaft pulley (5) and vibration damper (6) over Tooling (D) .

d. Install bolts (7) to the crankshaft pulley assembly.

Note: Evenly space bolts (7) around the crankshaft pulley assembly.

e. Tighten bolts (7) to a torque of 115 N·m (85 lb ft).

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/11/16
w 3/4(W)

4. If necessary, install friction shim (3) . Follow Step 4.a through Step 4.b in order to install
friction shim (3) .

a. Install friction shim (3) .

b. Install a new front seal to the front cover. Refer to Disassembly and Assembly,
"Crankshaft Front Seal - Remove and Install" for the correct procedure.

5. Install Tooling (A) to the crankshaft.

Illustration 2 g02458316

6. Install crankshaft pulley assembly (2) onto the crankshaft.

Note: Do not lubricate the front seal or the seal face of the crankshaft pulley assembly.

7. Install one Torx screws (1) to crankshaft pulley assembly (2) hand tighten.

8. Remove Tooling (A) .

9. Install remaining Torx screws (1) to crankshaft pulley assembly (2) .

10. Use a suitable tool in order to prevent the crankshaft from rotating. Tighten Torx screws (1)
to a torque of 40 N·m (29 lb ft).

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 2019/11/16
Thank you very much
for your reading.
Please click here to buy
After you pay.
Then, you can
download the complete
manual instantly.
No waiting.

You might also like