POWERING A SMARTER WORLD

M5 Plus
Outdoor Fingerprint & Card
Reader/Controller

Quick Guide V1.5

Package List

Device Screws RJ45 Connector USB Quick Guide

Notification:
1. Please check if the package contains all the items listed above. Contact
the distributor if there is any problem.
X4

RFID Card 2. Please keep the product away from the magnetic field, and avoid causing
any damage to the device.

3. Please use the original power supply or refer to the instruction to get
the right power supply.

4. Please strictly follow the instructions to install the product. Any damage
to it caused by incorrect operation and wiring are not under warranty.

1
Illustration for placing finger
Correct method ( Straighten your finger and then place it on the. sensor Ensure the finger is flat
and covers the entire sensor)

Always place finger in Try to place your finger covers the entire sensor.
the center of the sensor.

Incorrect method

DO NOT move your finger before DO NOT place finger away from DO NOT place finger
the sensor backlight turns off. the center of the sensor. at an angle.

DO NOT take off finger during DO NOT just use your fingertip. DO NOT slide your finger
the fingerprint verification during the fingerpint
process. verification process.
2
Installation Diagram

Back panel install way: Without back panel install way:

Step2 Steps: Steps:

Step1
Step1: Drill holes in the wall
Install M5 screws directly to the
follow the hole position on
bottom shell behind the wall , the
back panel.
36mm(1.42") depth of screws is 8mm(0.31"). This
install method is unique, safe and
Step2:Install and fix back
convenient. Package list does not
panel, connect related cables. 64mm(2.52")

include these screws,

10.5mm(0.41")
please select matchable screws
Step3:Place M5 Pro on back
accroding to the wall thickness.
panel, fix screw at the bottom
Step3 of M5 Pro.

Appearance
Indicator LED
"
Three color: Red,
"
Blue and Green.
Fingerprint Sensor
Place the finger here.

Card Reader Area Mini USB Port

"
Swipe the card here. Function Button

Screw Hole

3
Wiring Instruction

Function PIN Cable Color Description

DC12V
Connect RJ45 1 Red (Thick) DC12 VGND
Power
2 Black (Thick) GND
Tamper alarm

3 Pink (Thick) Tamper

Tamper Alarm alarm
Signal
Tamper alarm
4 Black Wiegand
Exit ButtonDATA0 Output

5 Green WiegandWiegand DATA1 Output

0 Input/Output
Wiegand
Output 6 White D/S
Wiegand 1 Input/Output

7 Black
Brown GND
Door Magnetic
Black GND
Pulse signal 8 Light brown RS485A
Light blue RS485A
9 RS485B
10 Blue NO RS485B

Relay Output 11 Light green COM NO

COM
12 Orange NC
NC

Switching Power Supply

1
+ 12V

2
Access Control Power Supply

GND

10

Power on to unlock 11
Access Control Power Supply

Switch Power
Supply 13

Important notice: Power off to unlock

Please carefully follow this wiring instruction. Any damage caused by incorrect wiring is not covered by warranty. 4
Wiring Type Access Controller

10
Switch Power
Supply 11

Power off to unlock

Power on to unlock

Anviz Wiegand Wiring:

SC011 and the device are paired by
Anviz wiegand to be a distributed access
control system.
Switch Power
Supply
Power off to unlock

+12V

+12V

Important notice:
.

5
SC011 authorization setting:
Make sure correct wiring between M5 Plus and SC011, power on them, then move
slide switch to ‘PROGRAM MODE’ as below:
Switch in‘PROGRAM’on the SC011: Move slide swith to left(ON).

Wiegand Wiring:
Between M5 Plus and Anviz SAC844 or other Access Controller as below:

Wiegand data output format:

1. Anviz Wiegand data output format:
ALL registered users output devieces’ last eight serial number.(For example, SN
of one device is 1050000014470004, then Anviz Wiegand output 14470004.)
2. Wiegand data output format:
Card user:Output card number.(Decimal)
Fingerprint user:Output ID number
3. Wiegand output format can be set by PC software

4
6
Function
* Button
*
*
* Pro Proto

7
Operation Guide
IMPORTANT:
M5 Pro is suitable for DC12V power supply only. When connect to DC12V power supply, the indicator
light displays blue and flashes fast. Meanwhile, the backlights of fingerprint sensor turn on with beeps.

Register User:

Add One Fingerprint per User Only:

Note: 1. After finish enrolling current user, 5. Continue to register another user
please swipe enroll card and then continue
register another user. 2. Place finger 3. Place finger 4. Swipe Enroll Exit
again Card once1
Enrollment
2. After finish enrollment, please swipe
enroll card TWICE to exit enroll status.
1. Swipe
Enroll Card 6. Swipe Enroll
Notice: Blue LED Blue LED flashes fast Green LED lights up Card TWICE to end
When you place finger on M5 Pro, Red LED flashes and fingerprint with 4 short beeps, the enrollment
flashing with two long beeps means the finger has sensor lights up registration successed
been registered.

Add Card Only:

Note: 1. After finish enrolling current user, 5. Continue to register another user
please swipe enroll card and then continue
register another user.
2. Swipe 3. Swipe User 4. Swipe Enroll Exit
User Card Card again Card once1
Enrollment
2. After finish enrollment, please swipe
enroll card TWICE to exit enroll status.
1. Swipe
Enroll Card 6. Swipe Enroll Card
TWICE to end the
Notice: Blue LED Blue LED flashes Green LED lights up
enrollment
flashes fast and with 4 short beeps,
When you swipe card on M5 Pro, Red LED FingerPrint registration
flashing with two long beeps means the card has sensor lights up successed
been registered.

8
Operation Guide

Add Two Fingerprints of one User: 8. Continue to register another user

* Two fingerprints belongs to one user ID.
4. Continue to register the 2nd finger
Note: 1. After finish enrolling current user, 2/5. Place the 3/6. Place the 1st/2nd 7. Swipe Enroll
please swipe enroll card and then continue 1st/2nd finger finger again Card once1 Exit
register another user. Enrollment

2. After finish enrollment, please swipe

enroll card TWICE to exit enroll status. 1. Swipe
Enroll Card 9. Swipe Enroll
Card TWICE to
Blue LED Blue LED flashes fast Green LED lights up end the
flashes and FingerPrint with 4 short beeps, enrollment
sensor lights up registration
successed

Add Fingerprint and Card of one User:

* The wiegand output of fingerprint and card are the same.

8. Continue to register another user

2. Place finger 3. Place finger 4. Swipe 5. Swipe User 7. Swipe EnrollExit

again User Card Card again Card once1
Enrollment

1. Swipe 9. Swipe Enroll Card

Enroll Card TWICE to end the
Blue LED Blue LED Green LED lights up Blue LED Green LED lights up enrollment
flashes flashes fast and with 4 short beeps, flashes fast and with 4 short beeps,
FingerPrint registration FingerPrint registration
sensor lights up successed sensor lights up successed

Note:
1. After finish enrolling current user, please swipe enroll card and then continue register another user.
2. After finish enrollment, please swipe enroll card TWICE to exit enroll status.

9
Operation Guide

Add Two Fingerprints and Card of one User:

* The wiegand output of fingerprint and card are the same.
10. Continue to register another user
Note: 1. After finish
enrolling current user,
please swipe enroll card 4. Continue to register the 2nd finger
and then continue register
another user. 2/5. Place finger 3/6. Place finger 7. Swipe 8. Swipe User 9. Swipe
again User Card Card again Enroll Card Exit
2. After finish once 1 Enrollment
enrollment, please
swipe enroll card
TWICE to exit enroll
status. 1. Swipe 11. Swipe
Enroll Card Enroll Card
Blue LED Blue LED Green LED lights up Blue LED Green LED lights up
flashes TWICE to end
flashes fast and with 4 short beeps, flashes fast and with 4 short beeps,
the
FingerPrint registration FingerPrint registration
enrollment
sensor lights up successed sensor lights up successed

Delete User:
Delete Fingerprint or Fingerprint and Card

After delete one user, you can continue to delete 4. Continue to delete
another user or swipe Delete Card to save and exit.
2. Place finger 3. Place finger
When fingerprints or card belong to one user again
ID, you can delete either one to delete this 5. Swipe Delete
user. Card to end
the process
1. Swipe
Notice: Delete Card
When you place finger on M5 Pro, Red LED Red LED Red LED flashes Green LED lights up
flashing with long beeps means the fingerprint flashes fast and with 4 short beeps,
does not exist in the device.
FingerPrint fingerprint deleted
sensor lights up

10
Operation Guide

Delete Card:

After delete one user, you can continue delete another 4. Continue to delete
user or swipe Delete Card to save and exit.
2. Swipe 3. Swipe User
User Card Card again
5. Swipe Delete
Card to end
the process
1. Swipe
Delete Card
Red LED Red LED flashes Green LED lights up
Notice: flashes fast and with 4 short beeps,
When you swipe card on M5 Pro, Red LED FingerPrint card deleted
flashing with long beeps means the card does sensor lights up
not exist in the device.

Delete All Users

Delete all uses fingerprints and cards, the

device parameter setting do not change.
2. Swipe 3. Swipe Enroll
Enroll Card Card again

4. Swipe Delete
Card to end
the process
1. Swipe
Delete Card
Red LED flashes Red LED flashes fast Green LED lights up
4 short beeps
Delete ASuccessed

Anviz brand and product are trademarked and protected under law of the United States.
Unauthorized use is prohibited.
For more information, please visit www.anviz.com , or send email to [email protected] for more help.
© 2020 Anviz Global Inc. All Rights Reserved. 11
201809
Bluetooth connection&configuration

Bluetooth connection&configuration:

1. Make sure your cell phone Bluetooth is on.

2. During the setup between app and the M5 plus, please make sure the mobile and M5
Plus are within effective distance（≦100CM)(≦39.37").

3. According to the strength of Bluetooth signal and MAC address from the Bluetooth
device which found by phone, you can check whether it’s the correct device or not.

App installation, setting & user registration:

9:41

Choose Your Role 1.Using the QR code which can get from the
Google play,
https://www.anviz.com/CrossChex.html or
manual to install the Crosschex Moblie APP

2. The interface of Mobile app will be like the

User
below picture when initializing.

Clicking the privacy policy,then if you choose

Administrator

user option to sign in, it will show green

《Privacy Policy 》
background colour, if you choose
administrator, it will show gray background
colour.
12
 9:41 9:41 9:41

Add Device M5 Plus Device List

M5 Plus
Bunded
D3:F8:64:61:84:21

M3 Pro Turn on Bluetooth of your

smartphone. Stay near the device
within around 3ft/1m.
M5 Plus
Unlock the door with
your phone.
M-Bio

C2 Slim

EP300 Pro
Get Started

How it works
A350 Start

SC211

Click the “Get Started” Choose the proper device The app can search and match the proper device.

9:41 9:41

Login Setting

Input the M5 Plus device default ID and password to

M5 Plus
Input your ID and Password from M5 Plus
your administrator
identify the setting, once matching successfully, it is
User ID
working with the voice and LED reminder.
M5 Plus

Password

Done
Default user id:0 password:12345
Next

13
 9:41 9:41 9:41 9:41

Device List Device List Device List My CrossChex

My Device
M5 Plus M5 Plus M5 Plus
Front Door Front Door Front Door
Logs

Support

Language

About

User Administrator

V 2.4

Rename Delete

Hold the circle area a Click the lock icon Choose the icon on the left top corner,
few seconds to modify to lock or unlock you can switch to normal user or admin
or delete device. user and do the record check...

9:41 9:41

Device List My CrossChex

M5 Plus
Front Door

When signing in as administrator on the

User Network Setting
app, administrator can choose one of
the available devices to finish the setup
at admin menu. Eg: user registration,
network setting, parameter etc.
Base Info

14
 In order to protect the environment, Anviz has decided to go "CD Free"
campaign since June 1st 2019. We will provide QR code for you to download
the electronic documents to make sure that you understand how to install
and use Anviz devices.

https://bit.ly/2Vn0wh6 https://bit.ly/2J9qA95

CrossChex Mobile App Google Anviz