1. In the context of static characteristics of a sensor, which of the following signifies resolution?
a. It provides the smallest change in the input that a sensor is capable of Sensing
b. It is the difference between the standard value and the value produced by Sensor
c. It is the deviation of sensor value curve from a particular straight line
d. It represents the correctness of the output compared to a superior system
Answer: (a)
Justification: Please refer to Slide 9 of Lecture 1 of Week 1
2. What is the general operating voltage range of commercial sensors which are available for
circuit enthusiasts and hobbyists?
a. 3.3 to 5 V
b. 4.5 to 8 V
c. 3.5 to 12 V
d. 3.3 to 8 V
Answer: (a)
EL
Justification: Please refer to page 185 (Section 8.2.6 – Operating Voltage) of the book
“Introduction to Industrial Internet of Things and Industry 4.0 by Misra et. al.”.
PT
3. Which of the following actuators produce linear displacement?
N
a. Manual Linear Actuator
b. Fluid Power Linear Actuator
c. Electric Linear Actuator
d. All of the above
Answer: (d)
Justification: Please refer to Slide 24, 26, 29 of Lecture 1 of Week 1
4. IEEE 802.15.4 uses ____________ protocol for data transmission.
a. ALOHA
b. CSMA-CA
c. CSMA-CD
d. None of the above
Answer: (b)
Justification: Please refer to Slide 6 of Lecture 2 of Week 1
5. Which of the following is not an operating frequency of ZigBee?
a. 950 KHz
b. 868 MHz
c. 902-928 MHz
d. 2.4 GHz
Answer: (a)
Justification: Please refer to Slide 11 of Lecture 2 of Week 1
6. What is/are the role(s) of adaptation layer in 6LoWPAN?
a. Packet fragmentation & packet reassembly
b. Compression of header
c. Routing of data link layer
d. All the above
Answer: (d)
EL
Justification: Please refer to Slide 18 of Lecture 2 of Week 1
PT
7. Maximum payload allowed in wireless HART is ______ bytes?
N
a. 63
b. 127
c. 255
d. 512
Answer: (b)
Justification: Please refer to Slide 25 of Lecture 2 of Week 1
8. Radio dead-spots can be bypassed using a process called _____.
a. Healing
b. Multi-hop
c. Adaptation
d. Reduction
Answer: (a)
Justification: Please refer to Slide 5 of Lecture 3 of Week 1
9. In which application domain does ISA 100.11a is primarily used?
a. Home/Office Automation
b. System for Smart Security and Surveillance
c. Systems for Smart Energy Management
d. Automation in large scale complex industries
Answer: (d)
Justification: Please refer to Slide 10 of Lecture 3 of Week 1
10. Which wireless communication technology is based on Ad-hoc Piconets?
a. Wireless HART
b. ZigBee
c. Bluetooth
d. Z-Wave
Answer: (c)
EL
Justification: Please refer to Slide 12 of Lecture 3 of Week 1
PT
11. What does the abbreviation, NFC, stands for?
N
a. New Frequency communication
b. Near Frequency communication
c. Near Field communication
d. Non-Friendly communication
Answer: (c)
Justification: Please refer to Slide 20 of Lecture 3 of Week 1
12. Which of the following work groups extend the integration of the IoT devices from network to
service level.
a. 6LoWPAN
b. ROLL
c. CoRE
d. None of the above
Answer: (c)
Justification: Please refer to Slide 7 of Lecture 4 of Week 1
13. QoS policies for IoT Network includes _______.
a. Resource utilization
b. Data timeliness
c. Data availability
d. All of the above
Answer: (d)
Justification: Please refer to Slide 12 of Lecture 4 of Week 1
14. Which IoT networking protocol supports caching capabilities to improve the response time
and reduce bandwidth consumption?
a. MQTT
b. XMPP
c. CoAP
d. AMQP
EL
Answer: (c)
Justification: Please refer to Slide 12 of Lecture 5 of Week 1
PT
15. Which IoT networking protocol is used in the Military?
N
a. DDS RTPS
b. IEEE 1888
c. AMCP
d. CoAP
Answer: (a)
Justification: Please refer to Slides 23 of Lecture 5 of Week 1
