G3 160T

Mobile Control

ORIGINAL EQUIPMENT
MANUFACTURERS BOARD

GPS, GLONASS and Galileo

signal tracking

• Dual frequency GPS and GLONASS

tracking capability
• Galileo GIOVE satellite tracking
• In-band interference suppression
capability
• 20 satellite, all-in-view, tracking
capability
• 20Hz RTK and update rate
• Scalable solution via software option
authorization (OAF)

The G3160T Eurocard offers state of the art

positioning based on GPS, GLONASS and now
Galileo satellite signals. Designed for integrators
who demand the ultimate in performance, the
G3160T is able to withstand 30 g acceleration
and output precise position computations at
a high rate.
 G3 160T Board Features & Specifications:
Tracking Features
• L1/L2 GPS, L1/L2 GLONASS, L1/L2 • Low signal tracking (down to 30
GPS + L1/L2 GLONASS, dBHz)
WAAS/MSAS/EGNOS, • Fast acquisition and fast re-
• GPS L5, GALILEO E1/E5a (hardware acquisition
compatible, in future after firmware • Cold start < 60 sec
upgrade) • Warm start < 35 sec
• Cinderella Option • Hot start: < 10 sec
• Up to 30 dB of “IN-BAND” • Reacquisition < 1 sec
interference suppression (in future • Up to 30 g’s of dynamic
after firmware upgrade) • Advanced Multipath Mitigation
• Co-Op Tracking (high satellites help
low satellites, in future after firmware
upgrade)
Data Features
G3 160T
• Up to 20 Hz update rate for real • NMEA 0183 versions 2.1, 2.2, 2.3 Powered by our Paradigm® GPS+
time position and raw data (code and 3.0 Output chip, the G3 160T includes dual
and carrier) • Geoid and Magnetic Variation
frequency GPS and GLONASS
• 10 cm code phase and 0.1 mm models
carrier phase precision • Different DATUMs support tracking capability with up to 20Hz
• RTCM SC104 versions 2.1, 2.2 and • Output of grid coordinates RTK and update rates. Its rugged
3.0 Input/Output • CMR and CMR+ support Eurocard interface and vast array of
Position Accuracy* input/output options provides easy
Dual Frequency: and reliable integration for the most
• Static, Fast Static • Kinematic, RTK demanding applications.
Horz: 3mm + 1ppm x (baseline) Horz: 10mm + 1.5ppm x (baseline)
Vert: 5mm + 1ppm x (baseline) Vert: 15mm + 1.5ppm x (baseline) And with Topcon’s exclusive software
option authorization capability (OAF),
Data Storage
you only pay for the capability you
• Up to 2 GB of on-board data storage (removable CompactFlash card).
need today…easily upgrade as your
Input/Output requirements change in the future.
• Four high speed RS232 serial ports • Two Event Marker inputs
(up to 460.8 Kbps). • MINTER interface:
• Full-duplex 10/100BASE-T E-net port. Four external LED drivers Other OEM Boards
• Full-speed USB device port (12 Mbps). ON/OFF control input External
• Direct connection to our GPS- command input TG-3
coupled spread spectrum radio. • Four General Purpose 3.3V CMOS The economical TG-3 board provides
• External Reference Frequency input/ inputs 50 channel GPS+GLONASS single
output • Eight General Purpose 3.3V CMOS
• Two 1PPS outputs (LVTTL) outputs frequency technology with up to
synchronized to GPS, UTC, or 100Hz data and position update
GLONASS capability.
Power Euro 112T
• Input supply voltage: 4.75V to 28V • On-board back-up battery for time Small Eurocard format (112mm),
• Power consumption: 4.0W typical; keeping and almanac data storage:
provides GPS L1/L2, and GLONASS
5.0W max 10 years of operation min
tracking, reduced power consumption,
Environmental and many of Topcon’s exclusive and
• Operating Temperature -40°C to +75°C advanced GPS+ features.
Other Euro 160T
Antenna output voltage - 5 VDC Back up battery - 10 years Standard 160mm Eurocard format
Main Connector delivers GPS L1/L2, and GLONASS
DIN41612, 2 row x 32 pin, Right Angle, Male, AMP 536052-5 is used on the board. tracking and all of Topcon’s exclusive
Dimensions and advanced GPS+ features.
160 x 100 x 14.2 mm
Antenna Connector
• Both RF connectors are MMCX RIGHT • J501 is External Reference Frequency
ANGLE PCB JACK, THROUGH HOLE/ connector.
AMPHENOL/908-24100.
• J101 is GNSS antenna input connector.
CAN Connector Mobile Control
HEADER,1X6, MOLEX 53261-0690 is used on the board (J601)
Topcon Positioning Systems
* With proper 50 ohm antenna 925.245.3300
** For Technical Drawings and additional Technical Specifications go to: www.topconsolutions.com
www.topconsolutions.com.