INSTRUMENTATION AND CONTROL

TUTORIAL 1 � BASIC ENGINEERING SCIENCE

This tutorial provides minimal engineering science necessary to complete the rest
of the
tutorials. Greater depth of the individual topics can be found on the web site. It
is useful to
anyone studying measurement systems and instrumentation but it is provided mainly
in
support of the EC module D227 � Control System Engineering. This tutorial is very
basic.

On completion of this tutorial, you should be able to explain and use the following
basic
relationships used in mechanical and electrical engineering science.

� Basic units.
� Displacement, velocity and acceleration.
� Newton�s Second Law of Motion.
� Springs.
� Pressure and flow.
� Resistance, current, capacitance and inductance.
� Stress and strain.
� Resistivity and temperature coefficient of resistance.
. D.J.Dunn 1
1. UNITS
There are only 5 basic units used in engineering. These are

mass kilogramme (kg)

length metre (m)
time seconds (s)
current Ampere (A)
temperature Kelvin (K)

Also used in physics is luminous intensity Candela (Cd). All other quantities used
are multiples of these
units.

2. FUNDAMENTAL MECHANICAL LAWS

2.1. VELOCITY
Linear
Velocity = rate of change of distance (m/s)

v = distance moved/time taken for constant velocity or x/t.

v = dx/dt for instantaneous velocity.

Angular
Angular velocity = rate of change of angle (rad/s)

w = angle turned/time taken for constant velocity or q/t.

w = dq/dt for varying conditions.

2.2 ACCELERATION
Linear
Acceleration = rate of change of velocity (m/s2).
a = dv/dt = d2x/dt2

Angular
Angular acceleration = rate of change of velocity (rad/s2)
a = dw/dt = d2q/dt2

2.3. NEWTON'S 2nd LAW OF MOTION

This concerns the force required to overcome the inertia of a body. Inertia (or
mass) is that property of a
body which opposes changes to its motion.

Linear
Angular

Force = Mass x acceleration Torque = Moment of inertia x angular acceleratio n

F = M dv/dt T = I dw/dt
F = M d2x/dt2 T = I d2q/dt2

2.4. SPRING
Linear
Force = constant x change in length (N)
F = kx

Angular
Torque = Constant x angle (N m)
T = k q
. D.J.Dunn
2
2.5. PRESSURE
Pressure = Force per unit area (N/m2)
p = F/A
1 Pascal = 1 N/m2
1 bar = 10 5 Pa

2.6. FLOW RATE IN PIPES

Flow rate = Cross sectional area x mean velocity
Q = A dx/dt

3. FUNDAMENTAL ELECTRICAL LAWS

3.1 CURRENT i = dq/dt (Coulomb/s or Amperes)
3.2 RESISTANCE V=IR (Ohm's Law)
3.3 INDUCTANCE
This law is equivalent to the 2nd. law of motion. Inductance (L Henries) is that
property of a component
that resists changes to the flow of current. The emf (E) produced is

E = L di/dt
E = L d2q/dt2

3.4. CAPACITANCE
This law is equivalent to the spring law. Capacitance (C Farads) is the property of
a component which
enables it to store electric charge.
Q = C V (Coulombs)

SELF ASSESSMENT EXERCISE No.1

1.
A spring is compressed 30 mm by a force of 50 N. Calculate the spring constant.
(1.67 N/mm)
2.
A mass of 30 kg is accelerated at a rate of 4 m/s2. Calculate the force used to do
it. (120 N)
3.
A flywheel is accelerated at a rate of 4 rad/s2 by a torque of 10 Nm. Calculate the
moment of inertia.
(2.5 kg m2)
4.
A force of 5000 N acts on an area of 400 mm2. Calculate the pressure in Pascals.
(12.5 MPa)
5.
A pipe 100 mm diameter carries oil at a mean velocity of 2 m/s. Calculate the flow
rate in m3/s.
(0.0157 m3/s)

6.
The current in an inductive coil changes at 30 A/s and the back emf is 3 V.
Calculate the inductance
in H. (0.1 H)
7.
A capacitor has a charge of 2 Coulombs at 24 V stored on it. Calculate the
capacitance in mF.
(83.3 mF)
8.
A flywheel turns 120 radians in 3 seconds at a constant rate. Calculate the angular
velocity. (40 rad/s)
. D.J.Dunn
3
4. STRESS AND STRAIN
4.1. DIRECT STRESS s
When a force F acts directly on an area A as shown in figure 1, the resulting
direct stress is the force per
unit area and is given as
s = F/A.
where
F is the force normal to the area in Newtons
A is the area in m2
and s (sigma) is the direct stress in N/m2 or Pascals.

Since 1 Pa is a small unit kPa , MPa and GPa are commonly used also.

If the force pulls on the area so that the material is stretched then it is a
tensile force and stress and this is
positive.
If the force pushes on the surface so that the material is compressed, then the
force and stress is

compressive and negative.

4.2. DIRECT STRAIN e
Consider a piece of material of length L as shown
in figure 1. The direct stress produces a change in
length DL. The direct strain produced is e
(epsilon) defined as e =DL/L
The units of change in length and original length
must be the same and the strain has no units.

Figure 1

Strains are normally very small so often to indicate a strain of 10-6 we use the
name micro strain and
write it as me.
For example we would write a strain of 7 x 10-6 as 7me.

Tensile strain is positive and compressive strain is negative.

4.3. MODULUS OF ELASTICITY E

Many materials are elastic up to a point. This means that if they are deformed in
any way, they will spring
back to their original shape and size when the force is released. It has been
established that so long as the
material remains elastic, the stress and strain are related by the simple formula

E= s /e

and E is called the MODULUS OF ELASTICITY. The units are the same as those of
stress.

. D.J.Dunn 4
ELASTIC LIMIT

A material is only elastic up to a certain point. If the elastic limit is exceeded,

the material becomes
permanently stretched. The stress-strain graph for some metals are shown below. The
modulus of
elasticity does not apply above the elastic limit. Strain gauges should not be
stretched beyond the elastic
limit of the strain gauge material which is approximately 3000me.

Figure 2
A typical value for the elastic limit of strain gauges is 3000 me.

WORKED EXAMPLE No.1

A metal bar which is part of a frame is 50 mm diameter and 300 mm long. It has a
tensile force acting
on it of 40 kN which tends to stretch it. The modulus of elasticity is 205 GPa.
Calculate the stress and
strain in the bar and the amount it stretches.

SOLUTION

F = 40 x 103 N.
A = pD2/4 = p x 502/4 = 1963 mm2
s = F/A = (40 x103)/(1963 x 10-6) = 20.37 x 106 N/m2 =20.37 MPa
E = s /e = 205 x 109 N/m2
e = s/E = (20.37 x 106)/(205 x 109) = 99.4 x 10-6 or 99.4 me

e = DL/L
DL= e x L = 99.4 x 10-6 x 300 mm = 0.0298 mm

4.4. POISSONS' RATIO

Consider a piece of material in 2 dimensions as shown in figure 2. The stress
in the y direction is sy and there is no stress in the x direction. When it is
stretched in the y direction, it causes the material to get thinner in all the
other
directions at right angles to it. This means that a negative strain is produced in
the x direction. For elastic materials it is found that the applied strain (ey) is

always directly proportional to the induced strain (ex) such that

(e x)/(e y) = -n

where n (Nu)is an elastic constant called Poissons' ratio.

The strain produced in the x direction is e x= -ne y

Figure 3

. D.J.Dunn 5
SELF ASSESSMENT EXERCISE No.2

1.
A metal wire is 1 mm diameter and 1 m long. It is stretched by a force of 2 N.
Calculate the change in
diameter. E = 90 GPa and n = 0.3 (Answer -8.5 x 10-6 mm).
Explain what happens to the resistance of the wire.

2.
Explain the significance of Poisson's ratio to the behaviour of strain gauges.
5. RESISTIVITY
The resistance of a conductor increases with length L and decreases with cross
sectional area A so we
may say R is directly proportional to L and inversely proportional to A.

R = Constant x L/A
The constant is the resistivity of the material r hence R = rL/A Ohms

SELF ASSESSMENT EXERCISE No.3

1.
Calculate the resistance of a copper wire 5 m long and 0.3 mm diameter. The
resistivity is 1.7 x 10-8
Ohm metre. (Answer 1.202 W)
2.
Calculate the resistance of a nichrome wire 2 m long and 0.2 mm diameter given r =
108 x 10-8
(Answer 68.75 W)

6. TEMPERATURE COEFFICIENT OF RESISTANCE

The resistance of conductors changes with temperature. This is a problem when
strain gauge devices are
used. Usually the resistance increases with temperature. The amount by which the
resistance changes per
degree per ohm of the original resistance is called the temperature coefficient of
resistance and is denoted

a. The units are Ohms per Ohm per degree.

Let the resistance of a conductor be Ro at 0oC.
Let the resistance be R1 at q1 oC. The change in resistance = aq1 Ro
The new resistance is R1 = Ro + aq1 Ro
Let the resistance be R2 at q2 oC. The change in resistance = aq2 Ro
The new resistance is R2 = Ro + aq2 Ro
If the temperature changes from q1 to q2 the resistance changes by

DR= R2 - R1 = (Ro + aq2 Ro ) - ( Ro + aq1 Ro )

DR = Ro aDq

SELF ASSESSMENT EXERCISE No.4

1.
A resistor has a nominal resistance of 120 W at 0 oC. Calculate the resistance at
20oC. Calculate the
change in resistance when the temperature drops by 5 degrees. a = 6 x 10 -3 W/W oC
(Answers 134.4 W and - 3.6W)

. D.J.Dunn
6