Solar pumping inverter user manual

1、 VFD500-PV Electrical cable Connection

Please follow the diagram below for wiring. And pay attention to the following issues：
Please follow the diagram below for wiring. And pay attention to the following issues：

+ PB - R S T U V W
DC-LINK POWER MOTOR

1 Figure 1-1 SIZE A~SIZE C 0.75kw-15kw Main Circuit Terminal

2 Figure 1-2 SIZE D 18.5kw-22kw main circuit terminal block diagram

3 Figure 1-3 SIZE E 30-37kw 4 Figure 1-4 SIZE F~G 45-90kw

1
 5 Figure 1-5 110kw-250kw Main Circuit Terminal Blocks

5 Table 1-6 Function description of the main circuit terminal of the inverter

Terminal Function instruction

R、S、T AC power input terminal, connect three-phase AC power or Solar+ -
U、V、W Inverter AC output terminal, connect three-phase AC motor
The positive and negative terminals of the internal DC bus are connected to the
+、-
external brake unit or For common DC bus
P1 and P2 are terminal to Connect DC reactor, short P1 to P2 when DC reactor
P1、P2
is not used (P2 is equivalent to "+" of DC bus)
+、PB Braking resistor connection terminal when built-in brake unit

Ground terminal, ground

Safety capacitor and varistor grounding selection screw (SIZE A~SIZE C EMC
EMC、VDR
screw on the left side of the fuselage)

 The power output of the PV panel is connected to the “+” and “-” terminals. Please note that the
polarity is not reversed.
 Make sure that the inverter input AC voltage level is consistent with AC grid voltage before
connecting with Input “R”, “S” and “T” terminals
 If Grid is single-phase power supply, you can connect to R T or any two terminals of “R”, “S” and “T”.
 If customer use PV solar only ,it is recommended to connect PV cable to any of RT
terminal,no polarity request

2
2、 VFD500M-PV Electrical cable Connection

Please follow the diagram below for wiring. And pay attention to the following issues：
Please follow the diagram below for wiring. And pay attention to the following issues：

5 Table 1-7 Function description of the main circuit terminal of the inverter

Terminal Function instruction

L1、L2、L3 AC power input terminal, or solar DC supply terminal
U、V、W Inverter AC output terminal, connect three-phase AC motor
+、PB + for solar positive and PB for solar negative

Ground terminal, ground

Safety capacitor and varistor grounding selection screw (SIZE A~SIZE C EMC
EMC、VDR
screw on the left side of the fuselage)

 The power output of the PV panel is connected to the any two terminal of L1 L2 L3 on priority
Or if L1 L2 L3 are connected for AC grid ,+ terminal is for solar positive and PB for solar negative.
 Make sure that the inverter input AC voltage level is consistent with AC grid voltage before
connecting with Input “L1”, “L2” and “L3” terminals
 If Grid is single-phase power supply, you can connect to L1 L2 or any two terminals of “L1”, “L2”
and “L3”。
 If customer use PV solar only ,it is recommended to connect PV cable to any of RT
terminal,no polarity request


1.1 Electrical Specifications

Table 1-1 Electrical Specifications

220V 380V

Max input DC voltage(VOC) 450V 800V

DC voltage range 160~450VDC 350~800VDC

Recommended DC input
250V-400V 450V-600V
voltage range (Vmpp)

3
 Recommended Input Operation
305V(Vmpp) 530V(Vmpp)
Voltage

MPPT efficiency >99%

Rated output voltage 1/3-phase 220VAC 3-phase 380-480VAC

Output frequency range 50/60Hz(maximum 600hz)

Max efficiency of the machine 99%

Ambient temperature range -10 °C~50 °C, derating if the temperature is above 40 °C

Cooling method Air cooling

Protection degree IP20/IP21

Altitude Below 1000m; above 1% for every additional 100m.

Standard CE/ROHS

Noted: We suggest solar panel power should be 1.4-1.5 times higher than solar pump power ,and solar pump
inverter power should be higher level than solar pump. When solar pump distance to inverter higher than
100m,it should be equipped with Output reactor or higher level power inverter .for Solar panel,l total VOC
less than Maximum DC voltage of inverter and Solar panel vmp is recommend 530V for 380V pump and 305V
for 220V pump

1.2 Power degree AND Technical SPECIFICATION

Power size of VFD500-PV refers to the standard 4 poles induction motor at rated voltage.
Overload: 150% rated output current, 1 minute

4
 Drive model Max DC input current (A) Rated output current (A) Applicable water pump (kW)

VFD500M-40T00150-PV 9 3.7 1.5

VFD500M-40T00220-PV 12 5 2.2

VFD500M-40T00400-PV 16.5 9.4 4

VFD500M-40T00550-PV 23.9 13 5.5

VFD500M-40T00750-PV 30.6 17 7.5

VFD500-40T00150-PV 9 4.2 1.5

VFD500-40T00220-PV 12 5.6 2.2

VFD500-40T00400-PV 16.5 9.4 4

VFD500-40T00550-PV 23.9 13 5.5

VFD500-40T00750-PV 30.6 17 7.5

VFD50040T01100-PV 39.2 25 11

VFD500-40T01500-PV 49.0 32 15

VFD500-40T01850-PV 50 37 18.5

VFD500-40T02200-PV 60 45 22

VFD500-40T03000-PV 81 60 30

VFD500-40T03700-PV 90 75 37

VFD500-40T04500-PV 130 90 45

VFD500-40T05500-PV 150 110 55

VFD500-40T07500-PV 200 152 75

VFD500-40T09000-PV 250 176 90

VFD500-40T11000-PV 300 210 110

VFD500-40T13200-PV 360 253 132

VFD500-40T16000-PV 430 304 160

VFD500-40T18500-PV 500 360 185

VFD500-40T20000-PV 550 380 200

VFD500-40T22000-PV 620 426 220

VFD500-40T25000-PV 680 465 250

220V Single phase/Three phase level

VFD500-20T00075-PV 6.7 4.5 0.75

VFD500-20T00150-PV 9.9 7 1.5

VFD500-20T00220-PV 14.1 10.6 2.2

VFD500-20T00400-PV 22.6 17 4

VFD500-20T00550-PV 30 25 5.5

5
 VFD500-20T00750-PV 40 32 7.5

VFD500-20T01100-PV 60 45 11

VFD500-20T01500-PV 81 60 15

VFD500-20T01850-PV 90 75 18.5

VFD500-20T02200-PV 130 90 22

VFD500-20T03000-PV 150 112 30

VFD500-20T03700-PV 200 152 37

VFD500M-20T00150-PV 9.9 7 1.5

VFD500M-20T00220-PV 14.1 10.6 2.2

Table 1-2 380V-480V rating data

Noted 1: when the output voltage is 380V, the output current will be rated value; when the output
voltage is 400V、415 V or 440V,the output current will be calculated according to power.

Noted 2: when the output voltage is 220V, the output current will be rated value

6
For 380V OR 220V or 110V Three phase motor Pump connection

Q2
Solar panels

Q1 + PB -
R U
3 phase power input
S V M
T W

Main circuit
Control circult
PLC
Connector slip
+24V
Start/stop terminal 485+
DI1 RS485 port
Forced switch to 485-
mains
DI2
AO1

HDI AO1、AO2 output:

AO2
0～10V/0～20mA
COM
GND
High water level switch
DI3 HDO
Low water level switch
DI4

COM COM

DO1
+10V
AI1
AI1、AI2 input:
0～10V/0～20mA AI2 COM
GND T1A
Relay 1 output,
T1B Default is fault
signal output
T1C

OFF OFF
T2A
485 AI1 AI2 AO1 AO2 Relay 2 output,
ON V V V V T2B Default is auto main
ON ON & PV switching
Water T2C
Well Grounding (Optional)
tower OFF I I I I

1.3 VFD500-PV Wire Diagram of solar pump inverter (three phase pump)

7
 Q2

Solar panels
Q1 + PB
R/L1 U
3 phase power input S/L2 V M
T/L3 W

Main circuit
Control circuit
+24V
Start/stop terminal
DI1 485+
Forced switch to RS485 port
mains 485-
DI2

HDI AO
AO output:
COM 0～10V/0～20mA
GND
High water level switch
DI3
Low water level switch
DI4
HDO
COM

COM

+10V
TA
AI input: AI1 Relay
0～10V/0～20mA TB output,Default is
AI2 fault signal output
TC
GND
OFF ON PE
I V AO
I V AI1
OFF ON 485

Water
Well
tower

1.4 VFD500M-PV Wire Diagram of solar pump inverter (three phase pump)

NOTE:
1:VFD500-PV Solar array output should be connected to the terminal ( +DC、－DC) of the
drive, please pay attention to the polarity of the solar array or you can connect solar array to R
and T but VFD500M-PV Solar array output should be connected to L1 L3 OR L1 L2 OR L2 L3
2: For control wire, recommend using shielded cable or shielded twisted pair.
3: Do not suggest using the power contactor to control the RUN/STOP of the drive.
4:In default carrier frequency, the maximum motor cable length is 100 meters. When the
motor cable is longer than 100m, it is recommended to use output reactor or DVDT filter or Sine
wave filter .

8
 For 220V single phase motor connection
1: Single phase asynchronous motor wiring method (without

starting capacitor):
Notice: U is connected to the common end of the starting winding and the working
winding, V is connected to the starting winding, and W is connected to the working
winding;

Single-phase asynchronous motor if the rotary steering is not correct, you can
change the V and W wiring or set P22.13=1。

First solution: Set parameter P11.01=1 (Single phase motor type without capacitor) or
second solution: set P00.11=00031 if your motor frequency is 50 hz or set P00.11=32 if
your motor frequency is 60HZ

Q2
Solar panels

Q1 + PB -
Public terminal
Single phase AC R U
power input Start winding M
S V
Working winding
T W

Main circuit

VFD500-PV Wire Diagram of solar pump inverter (single phase pump without capacitor)

Q2
Solar Panels

Q1 + PB -
Single phase AC R U
power input S V M
Public terminal
T W

Main circuit

VFD500M-PV Wire Diagram of solar pump inverter (single phase pump without capacitor)

9
For 220V single phase motor connection
2:Single-phase asynchronous motor wiring method (with capacitor)

Notice1:First solution: Connect motor cable to power terminal U and V and enter BSC
mode to Set parameter P23.15=0(output phase loss shielding protection) or second
solution: set macro P00.11=00021 if your motor frequency is 50HZ or set P00.11=22 if
your motor frequency is 60HZ

Q2
Solar Panels

Q1 + PB -
Single phase AC R U
power input S V M
Public terminal
T W

Main circuit

VFD500-PV Wire Diagram of solar pump inverter (single phase pump with capacitor)

Notes: Single phase motor has three lines, first use the universal meter to check the
three lines resistor, the biggest value two lines parallel the start capacitor (recommend
the capacitor volume is 150UF/250V), the other line(common-coil) connect the power
terminal. Then use the universal meter to check the common coil with the other two
lines resistor, the lower one connects another power terminal

10
Wiring method for Compensation of Grid and Solar DC supply

The back of the photovoltaic panel must be connected with anti-reverse diodes, and
the photovoltaic panel will be damaged after the current is recharged

Q2
-
+
Solar panels

Q1 AC Contactor(KM1) + PB -
R/L1 U
AC M
S/L2 V
Input~
T/L3 W
KM1
T2A

220V~ T2B

T2C

Wiring diagram of main circuit for simultaneous photovoltaic and power supply

11
1.4 Control Circuit Terminal
OFF

Jumper switch
ON

K2
I
485 AI1 AI2 AO1AO2

K1
OFF
ON

PE1 PE2

+10V AI1 AO1 485+ GND DI1 DI2 DI3 DI4 HDI T1/A T1/B T1/C

GND AI2 AO2 485- COM DO1 HDO COM PLC +24V T2/A T2/B T2/C

Diagram VFD500-PV control circuit terminal

Table VFD500-PV control circuit terminal instruction

Type Terminal Terminal Terminal function description
Symbol Name
10.10V±1%
Maximum output current:10mA，it provides power
+10V Input voltage
supply to external potentiometer with resistance range
of：1KΩ~51KΩ
Analog
GND Internal isolation from COM
ground
Input voltage:0~10V：Impedance 22KΩ，Maximum
input voltage
Analog input
Input current:0~20mA：Impedance 500Ω，Maximum
voltage AI1 Analog input1
input current
Through the jumper switch AI1 0 ~ 10V and 0 ~ 20mA
analog input switch, the factory default voltage input.
Input voltage:0~10V：Impedance 22KΩ，Maximum
input voltage
Analog input
AI2 Input current:0~20mA：Impedance 500Ω，Maximum
2
input current
Through the jumper switch AI2 0 ~ 10V and 0 ~ 20mA
12
 Type Terminal Terminal Terminal function description
Symbol Name
Analog input switch, the factory default voltage input.
Output voltage:0~10V：Impedance ≥10KΩ
Output current:0~20mA：Impedance 200Ω~500Ω
Analog output
AO1 Through the jumper switch AO1 0 ~ 10V and 0 ~ 20mA
1
analog output switching, the factory default voltage
output.
Analog Output voltage:0~10V：Impedance ≥10KΩ
output Output current:0~20mA：Impedance 200Ω~500Ω
Analog output
AO2 Through the jumper switch AO2 0 ~ 10V and 0 ~ 20mA
2
analog output switching, the factory default voltage
output.
Analog
GND Internal isolation from COM
ground
24V±10%，Internal isolation from GND
Maximum output current：200mA
+24V +24V current To provide 24V power supply, generally used as a
digital input and output terminal power supply and
external sensor power
The factory default setting is connected PLC with
Digital input +24V
Switch input
PLC terminal Terminal for on-off input high and low level switch
common When using the external signal to drive DI1~DI5, it
will disconnect the connector slip of PLC with the +24V
COM +24V ground Internal isolation from GND
Optocoupler isolation, compatible with bipolar input
Digital input
DI1~DI4 Frequency range：0~200Hz
terminal 1~4
Voltage range：10V~30V
Open Optocoupler isolation
Switch
DO1 collector Voltage range：0V~24V
output
output Current range：0mA ~50mA
T1A-T1B：normal close
Relay output
TA/TB/TC Relay output T1A-T1C：normal open
1
Contact rating：AC 250V，3A；DC 30V，1A
Relay T2A-T2B：normal close
output2 T2A/T2BT2C Relay output T2A-T2C：normal open
(optional) Contact rating：AC 250V，3A；DC 30V，1A
485 Positive
485+ differential
signal Baud rate：
485 port
485 Negative 1200/2400/4800/9600/19200/38400/57600/115200bps
485- differential
signal

13
2、Trial run(How to start solar pump inverter)
Make sure all cables connections of solar panel and pump motor correct and no
need to set any parameter, if you want to set parameter, you can do as follows.

Step 1: (Keypad control):Set motor parameter P11.02- P11.06 as per motor pump name
plate If dry run protection is required, measure the unload protection current(see details in
user manual chapter for dry run function) If dry run protection not required then miss this step
and go to step 2.

Step 2: Set other related special solar pump parameters for optimization if needed.

Step 3: After trial run finishing, if motor pump still not output water when inverter is running
more than 40 Hz. Please disconnect the power supply and replace any two-phase wiring of
the motor.

PMSM pump
Synchronous motor must be self-learning of motor parameters, otherwise there will be a risk
of flying,
P11.00=1 set to synchronous motor(special software)
P11.02=motor nameplate power
P11.03=Motor nameplate voltage
P11.04=Motor nameplate current
P11.05=motor nameplate frequency
P11.06=Motor nameplate speed
P11.22=Back EMF on the motor nameplate
If there is no such parameter on the nameplate, you can try to set 300V 350V for self-
learning (try self-learning for 380v level)
The difference between the back-EMF setting value and the actual value should be less
than 20%, otherwise the self-learning will be abnormal
After the parameter setting is completed, set P11.10=2, press RUN then the keyboard
appears Tune for self-learning.

Technical Questions and solutions

1. How to achieve Automatic start after stop?

If it is controlled by keyboard,so there is no need to set any parameter(P47.03 waiting time)If you want to
control by external switch,First set P00.06=1 and use a wire or switch to connect com and DI1，When the
switch is closed, the drive run, when the switch is open, the drive stop

2. How to use a float in the water tank to stop the pump if the tank is full?
If your float signal is digital signal Use float switch to short DI 3 and com ,see diagram 1.3

14
3.Use level probe in the well for protection against dry running
1st solution: See self learning of dry run(For LED display)
2nd solution: do it manually Set P24.13=30%-60%(as per real empty load current percentage based on
rated current) and P24.14 P24.16 and P23.21
3rd solution: If your sensor is digital switch ,just short D4 and com
4th solution:If your float signal is Analog signal, Connect Ai2 and 10V and GND and set P41.00=23 and
P41.03-P41.06

4.How to set minimum frequency ( for example) 30hz and maximum 50HZ
Set P47.05=30HZ and 47.06 to some time and 47.07 to some time. Please refer to details of P47.05-47.07

5.If pump is 60HZ frequency, how to set max frequency?

Notice: If your motor rated frequency is 60HZ First solution for you, P01.06=P01.08=P11.05=60HZ.
Quick setting and easier way: you should set P00.11=02 If your motor is three phase; if your motor is single
phase with capacitor ,set P00.11=22;If your motor is single phase without capacitor ,set P00.11=32

6. Does the product need to set a lot of parameters?

No, it doesn't. The inverter has a self-adaptive and self-learning function. It is automatic start and
stop, you can press Run key to start, or you just wait for P47.03=600S(Default) then it will automatically
start

7. Could it replace my previous PV pumping inverter?

Yes, of course. Selecting inverter model according to the rated voltage, current and power of the
water pump. A bit more is better. Then take off the old one and put ours on, the system will work.

8. How to design solar PV water pump system?

Key point: the rated VOC and VMP and power of the PV Array need to match the input range of
the inverter. If needed, we will provide technical support online.

9. How to make the water pump system work without sunshine?

Usually, solar PV water pump system can meet the needs of pumping water.
If there is no sunshine, the system will not work. But out inverter could also support AC input. So,
connect the power grid or diesel power generation to the inverter, the pumping system will work. If
necessary, keep switch and interface locations during the system design

10. How to check and solve basic problem of inverter trips and error
a：Check the total vmp and voc of solar panels ,solar panel technical data
b：Check motor pump power and rated current
c: Check the distance between motor and inverter
d: Check trip record r25.00 r25.01 25.02 25.03 r26.00 r26.01 r26.02 r26.03 r26.08 r26.09 r26.10 r26.11
e: Check troubleshooting fault and find relevant solutions
f : Check if motor insulation has been damaged or motor is blocked

15
3、Keypad display
3.1 LED Instruction of operation and display

LED keyboard consists of 5 digital tubes, 7 lights, 8 keys and a potentiometer; can be used to set the
parameters, status monitoring and operation control, LED keyboard shape as shown in Figure 4-1：

Figure 3-1 Operating panel

Description of indicator

Table 3-2 The name and function of each part of the keyboard
No. Part Name Function
1 Exit • exit menu level

2 Confirmation • Enter the menu interfaces level by level,

• confirm the parameter setting and save to EEPROM
3 Increment/Up • The number indicated by the cursor increases by one.
• Next function code.
• Used to switch the left and right screens while in monitor mode
4 Decrement/Down ·The number indicated by the cursor minus one.
• The previous function code.
5 Multi-function ·Perform function switchover according to the setting of
21.02
6 Shift • Cursor shift.
• Monitor Status Displays the next monitor volume.
• Switch left and right screens.
7 Run Start the frequency inverter in the operation panel control
mode

16
 8 Stop/Reset • During operation, press to stop the operation (restricted by
parameter 21.03).
• In fault status, press this key to reset the fault.

9 Indicator light:Hz ·Indicate the digital display unit, all three lights off menas other
units
10 Indicator light:A

11 Indicator light:V

12 Indicator When Hz" and "A" are lit at the same time, the unit of the currently
light:HZ+A(rpm/min displayed parameter is "RPM PER MINUTE
ute)
13 Indicator light: When "A" and "V" are lit at the same time, the unit of the currently
A+V(%) displayed parameter is "percent".
14 Running lights • Off: indicates a stop condition.
• On: indicates inverter is running.·
Blinking: Deceleration stopped.
15 Direction indicator • Used to indicate the sign of the variable when the LED is
displaying one of the variables listed in 27.02;
• In other cases the sign of the output frequency is indicated.
16 Command source • Off: The command source is the keyboard.
indicator • On: The command source is terminal.
• Blinking: The command source is communication.
17 Fault indicator • When it is on, the drive is faulty.

3.2 Display hierarchy and menu mode

VFD500-PV digital keyboard display is divided into four layers, from top to bottom are: monitoring status, menu mode

selection status, function code selection status, parameter editing / viewing status, as shown in Figure 4-2. In the menu mode

selection status, press 【UP】 or 【DOWN】 key to select menu mode, press 【ENTER】 to enter the selected menu

mode, the following describes several menu modes:

17
 SHIF SHIF SHIF SHIF
MONITO
R T T T T Monitoring
volume1
STATUS
Monitoring volume1 Monitoring volume2 Monitoring volume3 Monitoring volume4
ESC

MENU UP UP UP UP
CHOOSE “-bSC-
ESC

STATE ”
Standard mode DOWN User-difined mode DOWN DOWN DOWN
Check mode Wizard mode
ESC ENTER ESC ENTER ESC ENTER ESC ENTER

COMMAND
CODE
【UP、DOWN、SHIFT】 【UP、DOWN】 【UP、DOWN】 【UP、DOWN】

ESC ENTER ESC ENTER ESC ENTER ESC ENTER

PARAMETER
EDIT/VIEW
STATUS
【UP、DOWN、SHIFT】 【UP、DOWN、SHIFT】 【UP、DOWN、SHIFT】 【UP、DOWN、SHIFT】

3-3 Keyboard operation diagram

3.3 Monitor display(P21.00=1)

According to the running status of the inverter, the digital tube displays different
contents in turn. If the button has no operation, the next monitoring amount is
automatically displayed every few seconds; of course, you can also switch to the
next monitoring indicator

 When the inverter is in the stop state, the digital tube is cyclically scrolling to
display：
“00000”DC bus voltage（r27.03）given frequency（r27.01）“00000”
 When the inverter is in running state, the digital tube is cyclically scrolling to
display.：
“00000”DC bus voltage（r27.03）output frequency（r27.00）output current
（r27.06）output ac output voltage（r27.05）“00000”

3.4 Menu mode

After the solar pump inverter is power on, the keyboard menu mode is user-
defined mode. Most of users only need to pay attention to the parameters displayed
in this mode. To check the complete inverter parameters, press the and

keys while the keyboard is displayed . When the keyboard is displayed

, press the key to enter the basic menu mode.

18
3.5 Error code：For other alarm codes, please refer to Chapter 5 of the manual.
alarm code meaning
Light weak fault, please refer to function
Sleep
code P47.05~P47.07
A.FULL Full water protection P47.18-47.21

A.PoL Low power protection P47.22-47.24

Overcurrent protection P47.25-47.27

A.oC
Low water protection P47.33-47.36
A.Lor

Dry Dry dun protection see P24.12-24.14

After the above warning occurs, the solar pump inverter will decelerate to stop and
cannot be started again until the warning condition is not released. When the warning
is released, the system will start automatically.

During the warning, the digital tube will flash the alarm code, and after 2s, it will display
the other interface for 2s.

4、Solar pump special parameter User mode

fast quick start
Function Name Description Default Property
code
47 Group solar pumping special group
0：NO ACTION
11：Restore default parameter except for motor
parameter and auto-tune related parameter and
P00.03 RESET 0 ★
factory parameter
12:Restore default to factory parameter
13：Clear tripping record
0：keypad
1：terminal
Source of the Operation
P00.06 2：communication 0 ★
Command
 Command source: run、stop、forward、
reverse、jog、fast brake stop.etc
Numeric frequency
P00.07 00.00Hz～maximum frequency 50.00Hz ☆
setting
00001:Output three phase 50HZ
P00.11 Application Macro 00000 ★
00002:Output three phase 60hz
19
Function Name Description Default Property
code
00021:Output single phase with capacitor
50hz
00022:Output single phase with capacitor
60hz
00031:Output single phase without
capacitor 50hz
00032:Output single phase without
capacitor 60hz
00100:Grid and solar hybrid mode (default
50HZ)
00101：MPPT mode +PID mode

When P00.11=100, it will execute the following macro modification

1. P47.01=211 (auto start, enable MPPT, enable auto switch)
2. P07.03=47 (Mains action relay, normally closed for mains (when the automatic switching
mode is 2)
3. P07.16=1.000 Relay 1 action delay 1s
4. P07.17=1.000 Relay 1 reset delay 1s
5. P47.06=600s Mains switching judgment 10min
6. P47.07=3600s Mains use time 60min.
When P00.11=101, it will execute the following macro modification
1. P01.07=8 enable PID function
2. P40.06=50.00 The default setting is the midpoint
3. P40.39=1 PID shutdown operation
P01.06 Maximum frequency 10.00～600.00Hz 50.00Hz ★
P01.08 Upper limit frequency Lower limit frequency-maximum frequency 50.00Hz ☆
0:No function
1:READY
Relay 1 Output terminal 2:RUN
P07.03 function group(T1A T1B 3:Error1（stop fault） 3 ☆
T1C) 4:Error2（same as Error1 except
undervoltage）
5:Warning output(fault but in running)
0：Three phase AC asynchronous motor
AC asynchronous motor
P11.01 1：Single phase AC asynchronous motor 0 ★
TYPE
without starting capacitor
0.1kW～710.0kW
 when power is less than 1kw ,0.75kw set to
0.8 as per round up principle ,0.55kw motor
P11.02 Motor rated power Depend ★
set 0.6
 when change motor rated power,AC drive
will automatically set other parameter of

20
Function Name Description Default Property
code
motor name plate and motor model
parameter be careful to use
P11.03 Motor rated voltage 10V～2000V Depend ★
P11.02<30kW：0.01A
P11.04 Motor rated current Depend ★
P11.02>=30kW：0.1A
P11.05 Motor rated frequency 1.00Hz～600.00Hz 50.00Hz ★
P11.06 Motor rated RPM 1～60000rpm Depend ★
R16.02
0：Standard mode (display frequency only)
P21.00 Monitoring display 1：Automatic scrolling display（Check 3.1 in 0 ★
detail ）it show hz,current,power and voltage
220V level: 160V～300V
P23.02 Undervoltage threshold 220/380 ★
380V level: 350V～520V
Undervoltage trip 220V Level:160V～300V
P23.05 200/300 ★
threshold 380V Level:350V～520V
Output phase loss 0.0-25%, 0% means output phase detections
P23.15 25% ☆
function shielded
Unit:hour
Accumulative running
r27.15 ●
time

0: invalid
The parameters behind the 47 group
cannot be changed!
Solar pump Mppt 1: Enable, to enable the special mppt
P47.00 1 ★
function enable function of the PV pump inverter

Units digit’s: Startup mode

0: Manual start, the start mode is
determined by P00.06;
1: automatic start,
When P00.06 change, the association
changes here.
Solar pump control
P00.06=0, when inverter starts and stops by
P47.01 mode 011 ★
keypad control, it is automatically modified
to 1-automatic start
P00.06=1, when inverter starts and stops by
terminal control.it is automatically changed
to 0-manual start
Ten digit’s: MPPT function
0: MPPT is disabled; CVT control is used
21
Function Name Description Default Property
code
(voltage is given as P47.04).
1: Enable MPPT.
Hundred’s unit automatic switching function
0: Disabled (Can be forced to switch ac grid
through terminal function 62, invalid when
enabled)
1: Automatically switch to Photovoltaic
priority
2: Automatically switch to GRID power
priority
When Automatic switching is enabled, and
the light is weak, it will automatically switch
to the electric supply, and the MPPT function
is disabled at this time
In auto start mode, set the time from power
P47.03 Automatic start timing 600 ★
on to start. It is also waiting time to start
Set the starting voltage of the MPPT
algorithm.
P47.04 MPPT starting voltage 305V(530V) ★
When the MPPT function is disabled, this
value is the reference voltage.
If the output frequency is lower than this
value and exceeds P47.06, it will be
Light detection reported to Sleep and stop
P47.05 20Hz ☆
threshold If automatic switching is enabled, it will
switch to ac grid operation, and the MPPT
function will be disabled
P47.06 Light detection time See P47.05 for explanation. 120s ☆
After the sleep fault is reported, if the time
when Vdc is higher than the undervoltage
point is greater than the set value, the fault
Light weak wake up state is exited and the operation continues.
P47.07 600s ☆
time When the automatic switching is enabled,
after switching into the electric supply
operation for this time, it will try to switch into
the photovoltaic operation.
The amount of change in the bus voltage
during an MPPT cycle. The larger the value,
MPPT tracking step
P47.08 the faster the maximum power point is 2V ☆
length
found, but the lower the accuracy of the
maximum power point.
Regulator proportional 0.001~1.00 It is for immediate response
P47.09 0.05 ☆
gain speed, it is not recommended to change

22
 Function Name Description Default Property
code
0.001~1.00 tracking response.it is not
P47.10 Regulator integral gain 0.05 ☆
recommended to change
P47.28 Starting coefficient 0.000～1.000 0.850 ☆
Unit digit：fast starting
0：Disable 1：Enable
P47.30 Fast speed function 11 ☆
Ten digit：Fast mppt tracking
0：Disable 1：Enable

5、Detailed Parameter list

Symbol Description:
“☆” means that the set value of this parameter can be changed no matter the inverter is in
the stop state or in running state.
“★” indicates that the set value of this parameter cannot be changed while the inverter is
running.
“●” indicates that the value of this parameter is the actual detected record value and cannot
be changed.

47 Group solar pumping special group

Function Name Description Default Property

code
47 Group solar pumping special group
0: invalid
The parameters behind the 47 group
Solar pump Mppt
P47.00 cannot be changed! 1 ★
function enable
1: Enable, to enable the special mppt
function of the PV pump inverter
Units digit’s: Startup mode
0: Manual start, the start mode is
determined by P00.06;
1: automatic start,
When P00.06 change, the association
changes here.
Solar pump control P00.06=0, when inverter starts and stops by
P47.01 mode keypad control, it is automatically modified 011 ★
to 1-automatic start
P00.06=1, when inverter starts and stops by
terminal control.it is automatically changed
to 0-manual start
Ten digit’s: MPPT function
0: MPPT is disabled; CVT control is used
(voltage is given as P47.04).
23
Function Name Description Default Property
code
1: Enable MPPT.
Hundred’s unit automatic switching function
0: Disabled (Can be forced to switch ac grid
through terminal function 62, invalid when
enabled)
1: Automatically switch to Photovoltaic
priority
2: Automatically switch to GRID power
priority
When Automatic switching is enabled, and
the light is weak, it will automatically switch
to the electric supply, and the MPPT function
is disabled at this time
Remarks:
Inbuilt auto mppt software and algorithm which measure and detect every 2ms to adjust current and voltage to
find the best working maximum power The input of solar energy determines the frequency corresponding to the
maximum power point, because the actual pump power is positively related to the frequency. The maximum
power tracking is the power of the photovoltaic panel, which provides the input power to the inverter. The
power outside this point is less than the optimal working point.In other words, below this point, the frequency
of the pump driven by the inverter will drop. The specific operating point is determined by the characteristics of
the photovoltaic panel, not where we want to work. The high voltage is only for sufficient output under low light
conditions. If you do not consider such a demand, the configuration can be freely
Remaining time for The remaining time of the starting is
r47.02 -- ●
starting displayed In auto start mode,Unit: second
In auto start mode, set the time from power
P47.03 Automatic start timing on to start.It is also waiting time to start 600 ★

47.03 is waiting time to start solar pump inverter without press start button, Our solar pump inverter Is purely
automatic start ,no setting software and simple and smart
Make sure solar panels cables and motor cables are well connected ,it will automatically start after 600S,10
Minutes is a threshold ,if you want to test this function ,you can set P47.03=10s,so power off and power on ,it will
start after 10s
Set the starting voltage of the MPPT
algorithm.
P47.04 MPPT starting voltage 305V(530V) ★
When the MPPT function is disabled, this
value is the reference voltage.
This is Manual mppt threshold voltage ,when you want to use manual mppt mode ,first you need to set mppt
function disable P47.01=00 (Unit digit 0 is means manual control ,ten’digit 0 is means CVT enables also manual
mppt function ,you can check solar panel configuration and calculate VOC and VMP and set P47.04=VMP

Light detection If the output frequency is lower than this

P47.05 20Hz ☆
threshold value and exceeds P47.06, it will be reported

24
Function Name Description Default Property
code
to Sleep and stop
If automatic switching is enabled, it will
switch to ac grid operation, and the MPPT
function will be disabled
This is light detection threshold to measure solar radiation and solar power in a setting time (P47.06 Detection
time),if customer do not want to keep pump running below this frequency so it can make pump sleep below this
frequency ,for example ,if pump can not run to 20hz in a setting time ,inverter will sleep and stop. if solar power
is enough in detection time ,then it will not report sleep alarming and return to normal

P47.06 Light detection time See P47.05 for explanation. 120s ☆

For example :if customer want to keep pump sleep below 25HZ,so customer need to set minimum frequency to
25HZ P47.05=25HZ, if inverter can not run to 25hz in a time(it is set by P47.06),it will report “Sleep” alarming
(previous software show CCC), default 120s(Automatically modify to 600s when P00.11=100
After the sleep fault is reported, if the time
when Vdc is higher than the undervoltage
point is greater than the set value, the fault
Light weak wake up state is exited and the operation continues.
P47.07 600s ☆
time When the automatic switching is enabled,
after switching into the electric supply
operation for this time, it will try to switch into
the photovoltaic operation.
P47.07 is wake up time to make inverter restart again. If solar power is enough ,it will detect again after
600s(default value),so inverter will automatically try to start after 600s and try to run to this frequency in set
time(P47.06),if it can run to this frequency ,sleep alarm will disappear and inverter return to normal.(default value
Automatically modify to 3600s when P00.11=100)

The amount of change in the bus voltage

during an MPPT cycle. The larger the value,
MPPT tracking step
P47.08 the faster the maximum power point is 2V ☆
length
found, but the lower the accuracy of the
maximum power point.
P47.08 is mppt tracking step ,our solar pump inverter detect and adjust voltage and current every 2ms to search
the best working maximum power to drive the pump ,we recommend the user understand this parameter and do
not set and change without factory guidance ,the large in the value ,the faster the maximum power point is
found ,but the accuracy of the maximum power is lower
Regulator proportional
P47.09 0.001~1.00 0.05 ☆
gain
P47.10 Regulator integral gain 0.001~1.00 0.05 ☆
0.1 m3
r47.11 Today’s Pumping flow It shows the flow of water pumping today, it 0.0 m³ ●
will be cleared after power off
r47.12 Cumulative pumping 1 m3, 32 digits 0 m³ ●
25
Function Name Description Default Property
code
flow volume It shows the pumping flow volume
accumulated by the pump. The power can
be saved automatically after power-on, and
continue to accumulate on the original
basis after re-powering. It Can be cleared
to zero by P47.14.
Set 1 to clear zero for r47.12. This function
Cumulative pumping
P47.14 code automatically changes to 0 after the 0 ☆
reset
reset is completed.
r47.15 Current water flow 0.1 m3/h 0.0 m³/h ●
P47.16 Pump rated flow 0.1 m3/h 0.0 m³/h ☆
This parameter is only related with
Pump water frequency r47.15.Set the output frequency of the
P47.17 20.00Hz ☆
reference inverter when the pump can pump water
which can help to calculate water flow
Units: Water level monitoring channel
0: invalid
1:AI1
2:AI2
3:AI3
4: AI4
Full water level
P47.18 Note: DI terminal 60-full water detection is 00 ★
detection channel
independent of the local setting
Ten’unit: analog water level logic
0: positive logic 0.00%-empty water 100.0%-
full water
1: Inverse logic 0.00%-full water 100.0%-
empty water
0.0～100.0%
Full water level
P47.19 0.0% ☆
detection value

0.0～3000.0s
1. When DI-60 is valid
2. The analog detection channel is greater
than P47.19 (positive logic) or the analog
Full water level
P47.20 detection channel is less than P47.19 10.0s ☆
detection time
(inverse logic)
When 1 or 2 conditions are met and P47.20
is maintained, the system reports A.Full and
shuts down
Full water recovery 0.0～3000.0s
P47.21 10.0s ☆
time When the condition described in P47.20
26
Function Name Description Default Property
code
does not meet full water level detection
requirement ,it will be returned to normal
state after delay
Conditions for full water detection to take effect:
1. The DI terminal arbitrarily set to function No. 60 receives the input switch close signal. For example, when
P06.03 is set to 60, DI3 is closed.
2. When the ten’s digit of P47.18 is 0 and the analog input is greater than the detection value, for example:
set P47.18=01, P47.19=50%, at this time AI1 input is greater than 5V or 10mA
3. When the tens place of P47.18 is 1 and the analog input is less than the detection value, for example: set
P47.18=11, P47.19=50%, at this time AI1 input is less than 5V or 10mA
4. After 1, 2 or 3 conditions are met, the system will report A.FULL for the set time on P47.20
Full water recovery conditions:
5. The system enters the full water detection stage and displays A.FULL
When conditions 1, 2 and 3 are not met, and the maintenance time is greater than the time set in P47.21,
the system recovers.
Low power detection 0.0～6000.0kW
P47.22 0.0kW ☆
value 0.0-ineffective
0～1000s
During operation, when the actual output
Low power detection
P47.23 power (r16.02) is less than P47.22 and the 10.0s ☆
time
time of P47.23 is maintained, the system
reports A.Pol and stops.
0～1000s
When the condition described in P47.23
Low power recovery
P47.24 does not meet Low power protection 10.0s ☆
time
requirement ,it will be returned to normal
state after delay
Overcurrent detection
P47.25 0.0～999.9A 0.0A ☆
value
0.0～3000.0s
During operation, when the actual output
Overcurrent detection
P47.26 current (r27.06) is more than P47.25 and the 10.0s ☆
time
P47.26 time is maintained, the system
reports A.Pol and stops.
0.0～3000.0s When condition described in
Overcurrent recovery P47.26 does not meet Over current
P47.27 10.0s ☆
time protection requirement ,it will be returned to
normal state after delay
P47.28 Starting coefficient 0.000～1.000 0.850 ☆
Photovoltaic panel working coefficient = rated mppt voltage / open circuit voltage
Characteristics of photovoltaic panels for example 30.7/37.9 = 0.81
P47.29 Starting adjustment 10～100V 40V ☆

27
Function Name Description Default Property
code

Unit digit：fast starting

0：Disable 1：Enable
P47.30 Fast speed function 11 ☆
Ten digit：Fast mppt tracking
0：Disable 1：Enable
Fault automatic reset
P47.31 0.00～600.00 60.00s ☆
time
Function faults include: undervoltage fault Er.Lu1, soft start fault Er.Lu2, inverter overload Er.oL, motor
overload Er.oL1, inverter overheat Er.oH, motor overheat Er.oH1, motor overheat Er.oH1, user-defined fault
1 Er .Ud1, user-defined fault 2 Er.Ud2
Units: Water level monitoring channel
0: invalid
1:AI1
2: AI2
3: AI3
4: AI4
Low water level
P47.33 Note: DI terminal 61-water shortage 00 ★
detection channel
detection is independent of the local setting
Ten’s unit: analog water level logic
0: positive logic 0.00%-empty water 100.0%-
full water
1: Inverse logic 0.00%-full water 100.0%-
empty water
Low water level
P47.34 0.0～100.0% 0.0% ☆
detection value
0.0～3000.0s
1. When DI-61 is valid
2. The analog detection channel is less than
P47.34 (positive logic) or the analog
Low water level
P47.35 detection channel is greater than P47.34 10.0s ☆
detection time
(inverse logic)
When 1 or 2 conditions are met and P47.35
is maintained, the system reports A.Lor and
shuts down
0.0～3000.0s
Low water recovery
P47.36 When the conditions described in P47.35 10.0s ☆
time
are not met, it will be restored after a delay
Conditions for the water shortage test to take effect:
1. The DI terminal arbitrarily set to function No. 61 receives the input switch close signal. For example, after
P06.04 is set to 61, DI4 is closed.
2. When the ten’s digit of P47.33 is 0 and the analog input is less than the detection value, for example: set
P47.33=01, P47.34=50%, at this time AI1 input is less than 5V or 10mA
28
Function Name Description Default Property
code
3. When the ten’s digit of P47.33 is 1 and the analog input is greater than the detection value, for example:
set P47.33=11, P47.34=50%, at this time AI1 input is greater than 5V or 10mA
4. After 1, 2 or 3 conditions are met, the system will report A.Lor for the set time of P47.35
Water shortage recovery conditions:
5. The system enters the water shortage detection stage and displays A.Lor
6. When the conditions 1, 2 or 3 are not met, and the maintenance time is greater than the time set in
P47.36, the system will recover.
P47.37 Reserved
0.000s~30.000s
When the automatic switching is
completed, the inverter will delay this
Automatic switching
P47.38 time and wait for the power supply to 5.000s ☆
delay start time
stabilize before running
Be sure to be greater than the effective
and invalid delay of the output terminal
0:AC Electric power
(DO function No47 is the mains switching
function, when P47.01 hundreds place is
r47.39 Input power type 2, No.47 function will be activated when - ●
the photovoltaic is switched in)
1:Solar power

24 Group Pump dry run protection/unload detection parameter

0.00Hz~600.00Hz
Lower limit frequency When the operating frequency is greater
P24.03 20.00HZ ☆
of self-learning than or equal to this frequency, the load-off
self-learning can be performed
Dry run/Unload 0: No offload detection is performed;
P24.12 1 ☆
protection option 1: Enable dry run detection
Dry run/Unload 0.0 to 200.0%
P24.13 0.0% ☆
detection level The percentage of motor rated current.
Dry run Unload
P24.14 0.000s～60.000s 30.000s ☆
detection time
0.00Hz～Fmax
Unload detection offset
P24.15 Detection frequency=Fmax-P24.15 5.00Hz ☆
frequency

Reset time of dry run

P24.16 0.0～6000.0 240.0s ☆
protection
0000:Coast stop
Dry run detection
P23.21 1000:Fast stop 0000 ☆
mode
3000:Continue to run

29
Function Name Description Default Property
code

1. Set P47.00=0, P00.07=20.00-30.00, P00.06=0, and then press to run the drive

2. Check the function code P27.00, wait until its value becomes 20.00, and then enter the
function code P24.13,

3. press the keyboard and simultaneously for more than 2 seconds,, and if

the value changes, the load-off self-learning is completed(LCD display not support)

4. Press to stop running, set P47.00=1, P00.06=1, In this process, the pump no need to
take out from water

Saying P24.12 = 1, P24.13 = 40.0%, P24.14 = 3.0s, then the diagram is shown below.
12 1.2

10 1

8 0.8

OutPutCurrent(1.0A)
6 0.6
Load loss dection

4 0.4

2 0.2

0 0
0 5 10 15

Dry run logic curve

Seen from the diagram shown above, if the output current is fall down to 40.0% of
the max output current and the status last for P24.14 then the drive will set the alarm
dry. If with P23.21 is not set, then the drive will coast stop while if P23.21 is set to
value 3000, then the drive will keep on running with dry alarm.
41 Group Pump sleep and wake-up parameters：

Unit’digit: Sleep source selection

0: No sleep function
2: AI1 sleep
3: AI2 sleep
Ten’s digit: Wake-up source selection
1: AI1 wake up
2: AI2 wake up
Sleep/wake source
P41.00 Hundred's digit: Sleep wake-up direction 010 ☆
selection
selection
0: positive direction
Sleep source (AI1 ～ AI2)>P41.03, inverter
sleeps
Wake-up source (AI1 ～ AI2) <P41.04, the
inverter wakes up
1: reverse direction

30
Function Name Description Default Property
code
Sleep source (AI1 ～ AI2)<P41.03, inverter
sleeps
Wake-up source (AI1 ～ AI2)>P41.04, the
inverter wakes up

Note: If AI2 is connected to the liquid level

detection signal, please set this value to
"23". If there is no sleep source (the ones
place is 0), the wake-up function is
automatically invalid, and P41.03~P41.06
are invalid.
0～100.0%
Note: The liquid level is higher than this
P41.03 Dormant level 0.0% ☆
value and the duration exceeds P41.05, and
the pump sleeps.
0～100.0%
Note: The liquid level is lower than this value
P41.04 Wake up level 0.0% ☆
and the duration exceeds P41.06, the pump
wakes up。
P41.05 Enter sleep delay 0.0s～6000.0s 0.0s ☆
P41.06 Wake-up delay 0.0s～6000.0s 0.0s ☆

Basic function parameter

0 ~ 65535
 No user password status (P00.01 = 1 after
power-on):
Entering the same non-zero value twice in
succession sets a user password and enters
lockout.
P00.00 User password  password lock state: 0 ☆
Enter the password to enter the unlock state.
 unlocked state:
Enter the original password to enter the lock
state; enter the same value twice in a row to
change the password (clear the password if you
enter 0 twice in a row).
0：NO ACTION
11：Restore default parameter except for motor
parameter and auto-tune related parameter and
P00.03 RESET 0 ★
factory parameter
12:Restore default to factory parameter
13：Clear tripping record

31
Function Name Description Default Property
code
0：keypad
1：terminal
Source of the
P00.06 2：communication 0 ★
Operation Command
 Command source: run、stop、forward、
reverse、jog、fast brake stop.etc
Numeric frequency
P00.07 00.00Hz～maximum frequency 50.00Hz ☆
setting
0：Digital setting
1：AI1
2：AI2
3：AI3(reserved)
4：AI4（reserved）
Main frequency source 5：HDI
P01.00 0 ★
selection (A) 6：multi-step speed
7：communication
8：PID
9：Internal PLC
Notice:DI terminal function code 26-32 superior
than this function code

P01.06 Maximum frequency 10.00～600.00Hz 50.00Hz ★

0: Digital setting (P01.08)

1:AI1
2: AI2
Upper limit frequency 3~4: reserved
P01.07 0 ★
source 5: HDI
6: reserved
7: Communication
8: PID

P01.08 Upper limit frequency Lower limit frequency-maximum frequency 50.00Hz ☆

P01.09 Lower limit frequency 0.00hz-upper limit frequency 00.00Hz ☆

0：ramp to stop (Deceleration to stop)

P02.08 Stop method 0 ☆
1：free coast to stop
Minimum blocking
P02.15 0.010s-30.000s Depend on ★
time after free stop
Setting value depend on P03.16
P03.16 = 2, 0.00～600.00s; Depend on
P03.01 Acceleration time 1 ☆
P03.16 = 1, 0.0s～6000.0s; model
P03.16 = 0, 0s～60000s
Setting value depend on P03.16
P03.02 Deceleration time 1 P03.16 = 2, 0.00～600.00s; 5.00S ☆
P03.16 = 1, 0.0s～6000.0s;
32
Function Name Description Default Property
code
P03.16 = 0, 0s～60000s

0:No function
1:READY
2:RUN
P07.01 DO1 function 3:Error1（stop fault） 0 ☆
4:Error2（same as Error1 except
undervoltage）
5:Warning output(fault but in running)
0:No function
1:READY
2:RUN
3:Error1（stop fault）
P07.02 DO2 function 0 ☆
4:Error2（same as Error1 except
undervoltage）
5:Warning output(fault but in running)

0:No function
1:READY
Relay 1 Output terminal 2:RUN
P07.03 function group(T1A T1B 3:Error1（stop fault） 3 ☆
T1C) 4:Error2（same as Error1 except
undervoltage）
5:Warning output(fault but in running)
0:No function
1:READY
2:RUN
Relay 2 Output terminal
3:Error1（stop fault）
P07.04 function group(T2A T2B 47 ☆
4:Error2（same as Error1 except
T2C) optional
undervoltage）
47:Warning output(fault but in running)
auto main & PV switching

P07.12 DO1 effective delay time 0.000s～30.000s 0.000s ☆

DO1 ineffective delay

P07.13 0.000s～30.000s 0.000s ☆
time

P07.14 DO2 effective delay time 0.000s～30.000s 0.000s ☆

DO2 ineffective delay

P07.15 0.000s～30.000s 0.000s ☆
time
P07.16 Relay 1 effective delay Delay time from relay effective to actual action 0.000s ☆

P07.17 Relay 1 invalid delay The delay time from the deactivation of the relay 0.000s
☆
to the actual action
33
Function Name Description Default Property
code
0～200%
It is used to compensate the speed drop of the
asynchronous motor VF control with load, and
improve the speed control accuracy. Please
P12.11 Slip compensation gain adjust according to the following principles: 0% ☆
 Increase the setting when the motor speed
is lower than the target value with loading.
 Reduce this setting when the motor speed
is higher than the target value with loading,
0：Standard mode (display frequency only)
P21.00 Monitoring display 1：Automatic scrolling display（Check 3.1 in 0 ★
detail ）it show hz,current,power and voltage
Depend on drives power
≤7.5kW: 1kHz～12.0kHz
11kW～45kW: 1kHz～8kHz
≥55kw: 1kHz～4kHz
The carrier frequency can be reduced when it
came like following phenomenon:
1 The leakage current generated by the inverter
Carrier/swithcing is large
P22.00 Depend ☆
frequency 2 The interference generated by the inverter has
an impact on peripheral devices
3 Long wiring distance between inverter and
motor
The carrier frequency can be increased when it
came like following phenomenon:
1 The electromagnetic noise generated by the
motor is large
0:effective when running
Cooling method (fan 1:Forced control( effective when power on)
P22.14 2 ☆
control) 2:adjustable as per drive temperature

r22.16 Drive rated power Read only Unit:0.1kw - ●

r22.17 Drive rated Voltage Read only Unit:V - ●

r22.18 Drive rated current Read only Unit:0.1A - ●

After this time, the inverter will stop and report

Er.TTA fault; if set to 0, it will be cancelled. Note:
P22.20 Trial time setting 0 ☆
This parameter needs agency authority to be able
to see
0:No Operation
P22.13 Output phase switch 0 ★
1:Output phase switch

34
Function Name Description Default Property
code
(equal to change Phase between V and W and
UV and UW
 Unit’digit :Overvoltage stall control
0:overvoltage stall disabled
1:overvoltage stall enabled
2:overvoltage stall enabled self-adjustable
 The over-voltage stall function limits the amount of

power generated by the motor by extending the

deceleration time or even increasing the speed,

avoiding over-voltage on the DC side and reporting

over-voltage faults

Ten’unit:Undervoltage stall control

0:undervoltage stall disabled
1:Undervoltage stall(decelerate to zero
speed and be in standby mode,after
DC Bus voltage
P23.00 power restoring ,it will run again 10 ★
control option
automatically)
2: Undervoltage stall
deceleration(decelerate to zero and stop)
 The undervoltage stall function reduces the

motor power consumption or reduces the power

consumption of the motor or turns it into a

power generation operation to avoid the

undervoltage fault on the DC side.

The undervoltage stall function is used when the input

power supply quality is poor (the power supply voltage

fluctuates downward or the sporadic short power is

suspended), and it is necessary to keep the inverter running

as much as possible.

220V level: 160V～300V

Undervoltage
P23.02 380V level: 350V～520V Depend ★
threshold
480V level: 400V～650V
Undervoltage stall
P23.04 0～20.0 4.0s ☆
ratio
220V Level:160V～300V
Undervoltage trip
P23.05 380V Level:350V～520V Depend ★
threshold
480V Level:400V～650V
Undervoltage fault
P23.06 0.0s～30.0s 1.0s ☆
detecting time
Output phase loss 0.0-25%, 0% means output phase detections
P23.15 25% ☆
function shielded

P23.24 Fault reset Define as per bit: 0 ☆

35
Function Name Description Default Property
code
bit0-undervoltage;bit1- inverter overload
bit2-inverter overheat ;bit3-motor overload
bit4-motor overheat;bit5-user’fault 1
bit6- user’fault 2; bit7～15 reserved
Define as per bit:
bit0-overcurrent during acceleration;bit1-
overcurrent during deceleration
bit2-overcurrent during constant speed;bit3-over
voltage during acceleration
Fault source for auto bit4-overvoltage during deceleratoin;bit5-
P23.25 0 ☆
reset overvoltage during
bit6-inverter undervoltage;bit7-input phase loss
bit8-inverter overload;bit9-inverter overheat
bit10-motor overload;bit11-motor overheat
bit12-user’fault 1;bit13-user’fault 2
bit14-Reserved;bit15-Reserved

P23.26 Fault auto Reset times 0～99 10 ☆

P23.28 Fault reset internal time 0.1s-300.0s 60

Fault auto reset times

P23.29 0.1s～3600.0s 600.0s ☆
clearing time

11 Group Motor 1 Parameter

0：AC asynchronous motor
P11.00 Motor type 1：Synchronous motor(Special software) 0 ●
See appendix parameter
0：Three phase AC asynchronous motor
AC asynchronous motor
P11.01 1：Single phase AC asynchronous motor 0 ★
TYPE
without starting capacitor
0.1kW～800.0kW
 when power is less than 1kw ,0.75kw set to
0.8 as per round up principle ,0.55kw motor
set 0.6
P11.02 Motor rated power Depend ★
 when change motor rated power,AC drive
will automatically set other parameter of
motor name plate and motor model
parameter be careful to use
P11.03 Motor rated voltage 10V～2000V Depend ★
P11.02<30kW：0.01A
P11.04 Motor rated current Depend ★
P11.02>=30kW：0.1A
P11.05 Motor rated frequency 1.00Hz～600.00Hz 50.00Hz ★
P11.06 Motor rated RPM 1～60000rpm Depend ★

36
Function Name Description Default Property
code
0：no auto tuning
1：Stationary auto tuning of Asynchronous
motor
It is suitable in the cases when the motor can
not de-couple form the load. The auto tuning for
the motor parameter will impact the control
P11.10 Auto-tune/self-learning 0 ★
accuracy.
2：dynamic or Rotational auto tuning of
Asynchronous motor
Comprehensive motor parameter auto tune
It is recommended to use rotation auto tuning
when high control accuracy is needed.

★
Synchronous motor
P11.12 back electromotive force 0.0V ~ 2000.0V Induced electromotive force at Depend
BEMF rated speed

24 Group motor protection

0.20～10.00
Motor overload The larger the value, the longer the allowable
P24.00 1.00 ☆
protection gain overload operation, and the higher the risk of
motor overheating damage.
Motor overload starting
P24.01 50.0%～150.0% 100.0% ☆
current at zero speed
Motor overload starting
P24.02 50.0%～150.0% 115.0% ☆
current at Rated speed

Motor in self cooling mode, heat

dissipation is poor when in low
frequency but good in condition of high
frequency . P24.01 adn P24.02 is used to
set the starting point of zero and rated
speed overload current in order to
obtain a more reasonable under
different speed overload protection
Time curve
Motor overload protection
starting current
P24.02

P24.01
Motor output
frequency
0
Fn

37
Function Name Description Default Property
code

Overload
time
80min
Overload gain P24.00=1.20
64min
Overload gain P24.00=1.00

Overload gain P24.00=0.80

30min

5min
160s

5
s
100% 120% 140% 160% 180% 200% 220%
* Overload protection starting current

First graph: Motor overload protection starting current Second graph: Motor Overload Protection Curve with
Different Overload Protection Gains

Motor overload only protects the motor from overload when P24.04 is enabled.P24.00 is used to adjust the
overload inverse time curve time, as shown in the right figure above, the minimum motor overload time is 5.0s.
Note: Users need to correctly set the three parameters of P24.00, P24.01 and P24.02 according to the actual overload
capacity of the motor. If set unreasonable, prone to motor overheating damage and the inverter is not timely warning of
the danger of protection

27 Group Monitoring parameter

r27.00 Output frequency It can set unit as per Parameter P21.07 - ●
r27.01 Setting frequency It can set unit as per Parameter P21.07 - ●
bit0：direction of running frequency
bit1：direction of setting frequencybit2：direction
of main frequency
r27.02 Direction indicator - ●
bit3：direction of auxiliary frequency
bit4：direction of Up Down offset
bit5: reserved
r27.03 DC Bus voltage Unit：1V - ●
r27.04 VF separation setting unit：0.1% - ●
r27.05 Output AC voltage unit：0.1V - ●
r27.06 Output AC current unit：0.1A - ●
Output current
r27.07 unit：0.1%(100% of motor rated current) - ●
percentage
Accumulated power on
r27.14 Unit:hour - ●
time
Accumulated running
r27.15 Unit:hour - ●
time
r27.18 Heat sink temperature Unit:0.1 ℃ - ●
38
Function Name Description Default Property
code
Load speed =P27.00*P21.10
r21.16 Load speed display - ●
Decimal point digit defined by P21.11
0：0.01Hz；1: 1Rpm
P21.17 Speed display unit  r10.12, r27.00, r27.01 displaying unit 0 ★
selection

25 Group Fault tracking parameter

r25.00 Current fault type See detail chapter 5 fault diagnosis and solution - ●
r25.01 Output frequency at fault Unit:0.01Hz - ●
r25.02 Output current at fault Unit:0.1A - ●
r25.03 Bus voltage at fault Unit:V - ●
Running mode status
r25.04 See Parameter r27.10 in detail - ●
1st fault
Input terminal status at Bit0～Bit6 corresponds to DI1～DI7
r25.05 - ●
fault Bit12～Bit15 corresponds to VDI1～VDI4
r25.06 Working time at fault Unit:0.01S - ●
Accumulated working
r25.07 Unit:hour - ●
time at fault
Frequency source at
r25.08 Unit:0.01hz - ●
fault
Heat sink temperature at
r25.14 Unit: 0.1°C - ●
fault
r25.15 Low-level fault - - ●

26 Group Fault recording parameter

r26.00 Last fault 1trip type SEE DETAILS IN CHAPTER 5 - ●
r26.01 Output frequency at fault Unit:0.01Hz - ●
r26.02 Output current at fault Unit:0.1A - ●
r26.03 Bus voltage at fault Unit:V - ●
Running mode status
r26.04 See Parameter r27.10 - ●
1at fault
Input terminal status at Bit0～Bit6 corresponds to DI1～DI7
r26.05 - ●
fault Bit12～Bit15 corresponds to VDI1～VDI4
r26.06 Working time at fault Unit:0.01S - ●
Accumulated
r26.07 Unit:hour - ●
Working time at fault
r26.08 Last fault 2 trip type Same as last fault description - ●
r26.09 Output frequency at fault Unit:0.01Hz - ●
r26.10 Output current at fault Unit:0.1A - ●
r26.11 Bus voltage at fault Unit:V - ●
Running mode status
r26.12 - ●
1at fault

39
Function Name Description Default Property
code
r26.16 Last fault 3 trip type Same as last fault description - ●
r26.17 Output frequency at fault Unit:0.01Hz - ●
r26.18 Output current at faul Unit:0.1A - ●
r26.19 Bus voltage at fault Unit:V - ●

P40 PID Group

r40.00 PID final output value Read only unit:0.1% - ●
r40.01 PID final set value Read only:0.01% - ●
r40.02 PID final feedback value Read only:0.01% - ●
r40.03 PID deviation value Read only unit:0.01% - ●
Unit’s digit:PID main reference source(ref1)
0：Digtital setting
1：AI1
2：AI2
3：AI3(IO expansion board)
P40.04 PID reference source 00 ☆
4：AI4(IO expansion board)
5：HDI high frequency pulse
6：Communication
Ten’digit: PID Auxilary reference source(ref2)
Same as Unit’s digit
PID given feedback
P40.05 0.01～655.35 100.00 ☆
range
P40.06 PID digital setting 0 0.0～P40.05 0.00 ☆
Unit’s digit 0：PID feedback source1(fdb1)
0:AI1
1:AI2
2:AI3(option card)
3:AI4(option card)
4: PLUSE(HDI)
P40.11 PID feedback source1 5: Communication 00 ☆
6: Motor rated output current
7: Motor rated output frequency
8: Motor rated output torque
9: Motor rated output frequency
Ten’s digit : PID feedback source2 (fdb2)
Same as Unit’s digit
P40.15 Upper limit of PID output -100.0%～100.0% 100.0% ☆
P40.16 lower limit of PID output -100.0%～100.0% 0.0% ☆
0.00～200.0%
P40.17 Proportional gain KP1 5.0% ☆

0.01s～20.00s
P40.18 Integral time TI1 1.00s ☆

40
Function Name Description Default Property
code
0.000s～0.100s
P40.19 Differential time TD1 0.000s ☆

0:No PID operation at stop

1:PID operation at stop
P40.39 PID operation at stop 0 ☆

04 Group Analog input

Unit’s：AI curve selection
0：curve A
1：curve B
2：Curve C
P04.07 AI 1 Curve setting 3：Curve D 00 ★
Ten’unit：when input signal lower than minimum
input
0：equal to minimum input
1：equal to 0.0%
P04.08 AI1 filter time 0.000s～10.000s 0.100s ☆
0.00V～10.00V ( it is used to view the port
voltage of AI1. When AI1 is a current type
r04.09 AI 1 actual value - ●
(0~20mA) input, multiplying this value by 2 is
the input current (mA) of the AI1 port.)
-100.0%～100.0%(It is used to view the output
r04.10 AI 1 Conversion value - ●
of the AI1 mapped curve)
Unit’s：AI curve selection
0：curve A
1：curve B
2：Curve C
P04.11 AI 2 Curve setting 3：Curve D 01 ★
Ten’unit：when input signal lower than minimum
input
0：equal to minimum input
1：equal to 0.0%
P04.12 AI2 filter time 0.000s～10.000s 0.100s ☆
0.00V～10.00V ( it is used to view the port
voltage of AI2. When AI2 is a current type
r04.13 AI 2 actual value - ●
(0~20mA) input, multiplying this value by 2 is
the input current (mA) of the AI2 port.)
-100.0%～100.0%(It is used to view the output
r04.14 AI 2 Conversion value - ●
of the AI2 mapped curve)

41
Function Name Description Default Property
code
0.00V～
P04.25
Correspondin
g setting
P04.23 Curve A horizontal axis 1 0.00V ☆
P04.2
6

- P04.2
4 P04.2 AI
100.0% 3
P04.25

～
P04.24 Curve A vertical axis 1 Note: Input less than P04.23, 0.0% ☆
100.0%
output decided by curve ten’s
digit
Setting method mode for AI1 4~20mA
P04.23
form
P04.25 Curve A horizontal axis 2 ～ 10.00V ☆
1. Switch the corresponding AI1
10.00V
jumper on the IO board to current;
-
2. Set the function code: P04.07 Unit’s
100.0%
P04.26 Curve A vertical axis 2 place=0 (default), P04.23=2.00. 100.0% ☆
～
100.0%
Correspondi
ng setting

0.00V～ P04.30
P04.27 Curve B horizontal axis 1 0.00V ☆
P04.29

P04.28 AI
- P04.27 P04.29

100.0%
P04.28 Curve B vertical axis 1 0.0% ☆
～
100.0%
P04.27
Note: Input less than P04.27, output
P04.29 Curve B horizontal axis 2 ～ 10.00V ☆
decide by curve ten’s digit
10.00V

Setting method mode for AI2 4~20mA

-
form
100.0%
P04.30 Curve B vertical axis 2 1. Switch the corresponding AI2 100.0% ☆
～
jumper on the IO board to current;
100.0%
2. Set the function code: P04.11 one
place=1 (default), P04.27=2.00

42
Function Name Description Default Property
code

06 Group Digital input(Terminal function)

0：No function
1：Run terminal
DI1 Numeric input 2：Reverse/Forward and reverse switchover
P06.01 1 ★
function 3：Three wire control
4：Forward jog command
5：Reverse jog command
6：Terminal UP

DI2 Numeric input 7：Terminal DOWN

P06.02 8：Clear up UP/DOWN offset 62 ★
function
9：Coast to stop/free stop
10：Fault reset
11：Reverse forbidden
DI3 Numeric input 12：Switching run command to Keypad
P06.03 60 ★
function 13：Switching run command to Communication
14：fast stop
15：external stop
16：Switch between motor 1 and motor 2
17：Pause operatoin
18：DC braking
DI4 Numeric input
P06.04 19：Switch between torque and speed Control 61 ★
function
20：torque control disabled
21：Multi-step speed terminal 1
22：Multi-step speed terminal 2
23：Multi-step speed terminal 3
24：Multi-step speed terminal 4
25：frequency source switchover
26：Switch main frequency source to Numeric
frequency setting
27：Switch main frequency source to AI1
28：Switch main frequency source to AI2
DI5(HDI) Numeric input 31：Switch main frequency source to high-
P06.05 0 ★
function frequency pulse input
32：Switch main frequency source to
communication setting
33：Switch auxiliary frequency source to
numeric frequency setting
60:full water level detection
61:Low water level detection
62:forced switching to ac power

43
 Chapter 5 Fault Diagnosis and Solution

VFD500-PV inverter has 24 types of warning information and protection function. In case of abnormal
fault, the protection function will be invoked, the inverter will stop output, and the faulty relay contact of the
inverter will start, and the fault code will be displayed on the display panel of the inverter. Before
consulting the service department, the user can perform self-check according to the prompts of this
chapter, analyze the fault cause and find out solution. If the fault is caused by the reasons as
described in the dotted frame, please consult the agents of inverter or factory directly.

Fault
Fault Name Display Possible Causes Solutions
code

1. Confirm the insulation

1: Motor insulation aging resistance of the motor. If it is
2: The cable is damaged and contact, turned on, replace the motor.
short circuit 2. Check the power cable of
3:The distance between motor and the motor
Inverter unit Er. SC
1 inverter are too long. 3. Install reactor or output filter
protection
4: Output transistor breakdown 4, seeking technical support
5: The internal wiring of the inverter is 5, seeking technical support
loose, or the hardware is bad. 6. Check if the braking resistor
6:Brake transistor short circuit is damaged and the wiring is
correct.

1: Eliminate external faults.

1: The output circuit is grounded or 2: Perform the motor auto-
short circuited. Tuning in cold state
2: Motor auto-tuning is not performed. 3: Increase the acceleration
3: The acceleration time is too short. time.
4: Manual torque boost or V/F curve is 4: Adjust the manual torque
Over current not appropriate. boost or V/F curve.
Er.OC1
during 2 5: The voltage is too low. 5: Adjust the voltage to normal
acceleration 6: The startup operation is performed range.
on the rotating motor. 6: Select rotational speed
7: A sudden load is added during tracking restart or start the
acceleration. motor after it stops.
8: The frequency inverter model is of 7: Remove the added load.
too small power class. 8: Select a frequency inverter
Of higher power class.

44
 Fault
Fault Name Display Possible Causes Solutions
code

1: The output circuit is grounded or 1: Eliminate external faults.

short circuited. 2: Perform the motor
auto-tuning.
2: Motor auto-tuning is not performed.
3: Increase the deceleration
Over current 3: The deceleration time is too short.
Er.OC2 time.
during 3 4: The voltage is too low.
4: Adjust the voltage to normal
deceleration 5: A sudden load is added during
range.
deceleration.
5: Remove the added load.
6: The braking unit and braking 6: Install the braking unit
resistor are not installed And braking resistor.

1: The output circuit is grounded or 1:Eliminate external faults.

short circuited. 2: Perform the motor auto-
2: Motor auto-tuning is notperformed. tuning.
Over current
Er.OC3 3: The voltage is too low. 3:Adjust The voltage to normal
at constant 4
4: A sudden load is added during range.
speed
operation. 4: Remove the addedload.
5: The frequency inverter model is of 5: Select a frequency
too small power class. Inverter of higher power class.

1:The input voltage is too high 1:The power supply voltage is

2:The surge voltage is mixed in the reduced to the normal range
input power supply. 2:Install DC reactor
Overvoltage 3:Cancel the external force of
Er.OU1 3: There is an external force to drive
during 5 the draggable motor or install
the motor to run, or the brake type load
acceleration the brake unit
is too heavy
4:The acceleration time is too short 4: Increase the acceleration
5:The motor is shorted to ground time
5:Eliminate the part of the
1:the
groundpower
shortsupply
circuit voltage is
1:The input voltage is too high reduced to the normal range
2:The surge voltage is mixed in the 2:install DC reactor
input power supply. 3:Cancel the external force of
Overvoltage
Er.OU2 3: there is an external force to drive the the draggable motor or install
during 6
motor to run, or the brake type load is the brake unit
deceleration
too heavy 4: increase the decceleration
4:the decceleration time is too short time
5:the motor is shorted to ground 5:eliminate the part of the
ground

1:the power supply voltage is

1:The input voltage is too high
reduced to the normal range
2:The surge voltage is mixed in the
2:install DC reactor
input power supply.
3:Cancel the external force of
Overvoltage 3: There is an external force to drive
Er.OU3 the draggable motor or install
at constant 7 the motor to run, or the brake type load
the brake unit
speed is too heavy
4: increase the acceleration or
4:The acceleration or decceleration
decceleration time
time is too short
5:eliminate the part of the
5:The motor is shorted to ground
ground

45
 Fault
Fault Name Display Possible Causes Solutions
code

1:Check if the input power

supply is abnormal, whether
the input power terminal is
1: Instantaneous power failure occurs loose, whether the input
contactor or the air switch is
on the input power supply or input
abnormal.
phase loss
2:adjust the voltage to the
2: The frequency inverter's input
Er.Lv1 normal range
Low voltage 8 voltage is not within the allowable
3:Power off after the inverter
range.
stops
3: Cut off the power during operation
4:seeking technical support
4:the internal wiring of the inverter is 5: For the unstable power
loose, or the hardware is bad. supply, if the performance
requirements are low, try to
enable the undervoltage stall
function (P23.00).
1:Check if the input power
supply is abnormal, whether
the input power terminal is
loose, whether the input
1: Instantaneous power failure occurs contactor or the air switch is
on the input power supply abnormal.
2: The frequency inverter's input 2:adjust the voltage to the
Er.Lv2 voltage is not within the allowable normal range
Contactor open 9
range. 3:Power off after the inverter
3: Cut off the power during operation stops
4:the internal wiring of the inverter is 4:seeking technical support
loose, or the hardware is bad. 5: For the unstable power
supply, if the performance
requirements are low, try to
enable the undervoltage stall
function (P23.00).
1. Reduce the load and check
the motor and mechanical
1:The load is too large or the motor is
conditions.
blocked.
2, increase the acceleration
2:The large inertia load acceleration and
and deceleration time
Frequency deceleration time is too short
Er. Ol 3. Adjust the torque boost or
inverter 10 3: When the VF is controlled, the torque
V/F curve
overload boost or V/F curve is not suitable.
4, select the inverter with a
4:The frequency converter selection is
larger power level
too small
5. Perform motor self-learning
5:Overload at low speed operation
in cold state and reduce carrier
frequency at low speed

46
 Fault
Fault Name Display Possible Causes Solutions
code

1. Reduce the load and check

the motor and mechanical
conditions. Correctly set the
1:The load is too large or the motor is motor parameters and motor
blocked. protection parameters.
2:The large inertia load acceleration and 2, increase the acceleration
deceleration time is too short and deceleration time
Motor Er.oL1 3:When the VF is controlled, the torque 3. Adjust the torque boost or
11
overload boost or V/F curve is not suitable. V/F curve
4:The motor selection is too small 4, select a motor with a higher
5:overload at low speed operation power level
6:Improper setting of motor parameters 5. Perform motor self-learning
and motor protection parameters in cold state and reduce carrier
frequency at low speed
6, check the settings of related
parameters

1: The three-phase power input is

1:Eliminate external faults.
abnormal.
Power input Er.iLP 2: Ask for technical support.
12 2: The drive board is faulty.
phase loss 3: Ask for technical support.
3: Thelightning proof board is faulty.
4: Ask for technical support.
4: The main control board is faulty.

1: The cable connecting the frequency

1:Eliminate external faults.
inverter and the motor is faulty.
2: Check whether the
2: The frequency inverter's
Power output Er.oLP Motor three phase winding
13 three-phase outputs are unbalanced
phase loss is normal.
when the motor is running.
3: Ask for technical support.
3: The drive board is faulty.
4: Ask for technical support.
4: The IGBT module is faulty.

47
 Fault
Fault Name Display Possible Causes Solutions
code

1: The ambient temperature is too 1:Lower the ambient

high. temperature.
2: The air filter is blocked. 2: Clean the air filter.
IGBT Module Er. oH 3: The fan is damaged. 3: Replace thedamaged fan.
14
overheat 4: The thermally sensitive resistor of 4:Replace the damaged
the IGBT module is damaged. thermally
5: The inverter IGBT module is sensitive resistor.
damaged 5: Replace the inverter module.

1:check the temperature sensor

wiring
1:The temperature sensor wiring is
2:Improve the carrier frequency,
loose
strengthen the heat dissipation
Motor Er. oH3 2:The motor temperature is too high
16 of the motor, reduce the load,
overheat 3:Themotor temperature sensor detects
and select a motor with higher
that the temperature is greater than the
power.
set threshold.
3:Check if the set threshold is
reasonable.

1: Reduce the load and check

1: The load is too heavy or locked- the motor and mechanical
By wave
Er.CbC rotor occurs on the motor. condition.
current 17
2: The frequency inverter model is of 2: Select a frequency inverter
limitingfault
too small power class of
higher power class.

1. Confirm the insulation

1. Motor burnout or insulation aging resistance of the motor. If it is
2, The cable is damaged and contact, turned on, replace the motor.
short circuit 2. Check the power cable of
Ground short Er.GF
18 3. The distributed capacitance of the the motor to eliminate the fault
circuit
terminal and motor cable is larger point.
motor cable 3, reduce the carrier frequency,
4, Hardware is damaged install the output reactor
4, seeking technical support

1, Temperature detection line broken 1. Check the thermistor wiring

module 2, Drive board is faulty 2. Ask for technical support
Er.tCK
temperature 20 3. Main control board is faulty 3. Ask for technical support
detection fault 4, The environmental temperature is too 4, manual intervention to drive
low the temperature rise

48
 Fault
Fault Name Display Possible Causes Solutions
code

1: Replace the faulty HALL

1: The HALL device is faulty. device.
Current Er.Cur
21 2: The drive board is faulty. 2: Replace the faulty drive
detection fault
3: The control board is faulty board.
3: Ask for technical support.

1 check motor and mechanical

1. Motor locked condition
Er.PGL
Encoder offline 22 2. Encoder pulse setting wrong 2 set correct parameter for
3. Encoder offline encoder
3 check encoder connecting line

1: Set the encoder

1: The encoder parameters are
parametersproperly.
setincorrectly.
2: Perform the motor auto-
Motor Er. oS 2: The motor auto-tuning is
25 tuning.
over-speed notperformed.
3: Set the over-speed detection
3: The over-speed detectionparameters
parameter correctly based on
are set incorrectly
the actual situation.

1: Set the encoder parameters

1: The encoder parameters are
properly.
setincorrectly.
Too large 2: Perform the motor auto-
Er.DEV 2: The motor auto-tuning is
speed 26 tuning.
notperformed.
deviation 3: Set the detection parameters
3: The detection parameters of toolarge
correctly based on the
speed deviation are setincorrectly.
actualsituation.

1: Set the motor parameters

according to the
Motor 1: The motor parameters are not set
Er.tU1 nameplateproperly.
auto-tuning 27 according to the nameplate.
2: Check the cable connecting
fault 1 2: The motor auto-tuning times out.
between the Frequency
inverter and themotor.
1: Set the motor
Motor 1: The motor parameters are not set parametersaccording to the
Er.tU3 nameplateproperly.
auto-tuning 28 according to the nameplate.
fault 3 2: The motor auto-tuning times out. 2: Check the cable connecting
between the Frequency
inverter
1、Confirmand whether
themotor.
the load is
off
Er. LL 1、The frequency inverter running
Off load 31 2、Check that the load is
currentis lower than the setting value.
disconnected or the parameter
setting is correct
EEPROM 1、 Operate Eeprom suitable
Er.EEP 1、 Eeprom Operate too frequent
read- write 32 2、 Replace the main control
2、 The EEPROM chip is damaged.
fault board

49
 Fault
Fault Name Display Possible Causes Solutions
code

Running time Er.TTA

33 Inverter trial time arrival 1:Contact agent or distributor
arrival

1. Check the connection of

1, The work of the host computer is not
upper computer
normal
485Communicatio Er.485 2. Check the communication
34 2, The communication line is not normal
n fault connection line
3, The communication parameter set is
3. Set communication
incorrect
parameters correctly
1、 PID feedback<P40.35 setting value
PID feedback 1、 Check PID feedback signal
Er.FbL and P40.36 not zero,PID
lost during 36 2、 P40.35 and P40.37 set
feedback>P40.37 setting value and
running correct parameter
P40.38 not zero

1: The signal of user-defined fault 1 is

User-defined Er.Ud1 input via DI. 1: Reset the operation.
37
fault 1 2:The signal of user-defined fault 1 is 2: Reset the operation
input via virtual I/O.

1: The signal of user-defined fault 2 is

User-defined Er.Ud2 input via DI. 1: Reset the operation.
38
fault 2 2:The signal of user-defined fault 2 is 2: Reset the operation
input via virtual I/O.

If output frequency is lower than light

Light weak Sleep
39 detection threshold and Solar radiation Check P47.05 and 47.07
warning
is too weak

A.FU Detect the water full alarm and low water

Full water
40 LL level through DI terminals, realizing Check P47.18 to 47.21
protection
automatic level control

During the operation of the photovoltaic

A.PLo pump, for some reason, the output
Lower power
41 power is less than Check P47.22 to 47.24
protection
P47.22(minimum power protection
value)

During operation, when the actual

A.oC output current (r27.06) is less than
Over current
42 P47.25 and the P47.26 time is Check P47.25 to 47.27
protection
maintained, the system reports A.oC
and stops.

50
 Chapter 6 Service Agreement

1. Guarantee Free-service period is 18 Month valid since delivery date from

factory which was subjected to the serial number on the drive rating
label.

2. Service free for Failure or trouble caused by our product quality issue.

3. For the service that Exceeding Guarantee time or failure not caused by
drive quality issues is out of the free range:
 From inappropriate, negligent or incorrect installation or adjustment
of the optional operating parameters of the equipment or from
mismatching the drive with the motor;
 Not permitted by the factory supplier, modified the drive devices;
 Out of the VFD500-PV product specification application;
 Failure consequences by fire, flooding, earthquake etc., un-foresee
natural disasters;
 Without drive’s serial number or the S.N. can not be identified clearly.

4. Technical support hotline:+86- 075589587650

51
 Solar pump inverter maintenance warranty card

User corporation:

Address:

Post code: Contractor:

Tel. no.: Fax no.:

Solar pump inverter type:

Product information Power size(kW): S.N.:

Contract no.: Purchase date:

Service engineer: Tel. no.:

Repair record Fixed date:

Fault information:

Complaints and demanding on our products:

User signature: year month date

Return visit record:

Service signature: year month date

52