Questions

Theory

1. Define rock and soil. Describe the formation procedure of cohesive and cohesionless soil.
2. Define soil mechanics. Explain its importance in civil engineering with practical examples.
3. Explain rock cycle. Describe various types of soil in detail.
4. Why is soil a multi-phase material?
5. Define phase diagram and derive the following relationship

𝐺𝑠 𝛾𝑤 (1 − 𝑛𝑎 )
𝛾𝑑 =
(1 + 𝑤𝐺)
𝑤
Sr = 𝛾𝑤 1
(1+𝑤)−
𝛾 𝐺

Sre = wG

𝐺 + 𝑆𝑒
𝛾 = ∗ 𝛾𝑤
1+𝑒

Where all symbols stand for their usual meaning.

6. Explain hydrometer analysis in detail.
7. Determine the maximum possible void ratio for a uniformly graded soil. Also find the porosity.
8. Compare the AASHTO classification system and Unified Soil Classification System.
9. Differentiate ISCS and USCS method of soil classification.
10. List out the methods for field identification of silt and clay. Describe dispersion test.
11. Explain the textural type of soil classification.
12. What are the purposes and requirements of soil classification?
13. Describe the type of soil structures that can occur in nature.
14. Explain about different types of clay minerals.
15. Define compaction. Describe standard proctor test and the modified proctor test. Draw typical
moisture density graph and explain salient features of it.
16. What do you mean by compaction at dry of optimum and at wet of optimum?
17. Briefly mention the factors affecting compaction. What is relative compaction?
18. Describe the behavior of fine-grained soil when compacted at dry of optimum and wet of optimum.
19. Mention purposes of compaction. Differentiate between compaction and consolidation.
20. How can quality control of compaction be done in field? Explain.
21. Determine the method to obtain the coefficient of permeability of soil in an unconfined aquifer.
22. Define quick sand condition and derive the expression for critical hydraulic gradient in terms of
specific gravity and void ratio.
23. Define permeability and describe well pumping test to obtain in-situ coefficient of permeability of
soil in case of confined aquifer.
24. How can you determine the average permeability of a stratified soil deposit? Describe.
25. Quick sand is not a special type of soil. It is a hydraulic condition. Justify with expression of critical
hydraulic gradient. Why is it mostly likely to occur in fine sand?

Compiled By: Abhash Acharya 1

26. A cohesive soil does not become quick as soon as the effective stress is reduced to zero. Justify.
Derive the critical hydraulic gradient for quick sand condition.
27. What are the assumptions of Laplace’s equation? Prove that flow lines intersect equipotential lines
at right angles.
28. Define flow lines and equipotential lines. Derive Laplace equation for two-dimensional flow
making suitable assumptions.
29. What are the limitations of Boussinesq theory? Compare between Boussinesq and Westergaard
𝑟
theory. Show that the maximum value of vertical stress on a vertical plane occurs at a depth of 𝑧 =
0.816.
30. Starting from Boussinesq’s equation, derive an expression for vertical stress under a circular area
of radius ‘ R’ carrying uniformly distributed load of intensity ‘q’ per unit area.
31. Define Mohr – Coulomb failure critera. Using this criteria, derive obliquity equation.
32. What is meant by pre-consolidation pressure?
33. What is degree of consolidation? What do you know about hydrodynamic lag? Derive an
expression for Terzaghi’s theory of one-dimensional consolidation.
34. Why is unconfined compression test a special type of tri – axial test?
35. What is a stress path? Explain the vane shear test for determination of shear strength parameters of
soil and also derive the expression for applied torque during one-way shearing.
36. What is meant by critical height of a slope?
37. Describe modes of slope failure.
38. Write short notes on:
• Normally Consolidated Clay and Over Consolidated Clay
• Stress Path
• Stability Analysis of Finite Slopes
• Onion Bulb Concept
• Consistency Limit of Soils

Compiled By: Abhash Acharya 2

 Numerical

1. The result of a liquid limit test is given below

No of blows 48 38 29 20 14
Water content 32 35 40 46 52
(%)
i) Determine the liquid limit of the soil.
ii) If the plastic limit of the soil be 23%, find the plasticity index, flow index and toughness
index.
2. The result of liquid limit test is given below:
No. of 33 23 18 11
blows
Water 41.5 49.5 51.5 55.6
content %
The plastic limits from two tests are 23 % and 24 % respectively. Determine plasticity index and
toughness index for the soil.
3. A clay sample containing its natural moisture content weighs 0.33 N. The specific gravity of solid
of this soil is 2.70. After oven drying the soil sample weighs 0.2025 N. The volume of the moist
sample before oven drying found by displacement of mercury is 24.30 cm3. Determine the moisture
content, void ratio and degree of saturation of soil.
4. 500g of dry soil was subjected to a sieve analysis. The weight of soil retained on each sieve is as
follows:
Sieve Size 4.75mm 2mm 1mm 425µ 212µ 150µ 75µ Pan
Wt. of soil retained on 10 165 100 85 40 30 50 20
sieve (g)
Plot the grain size distribution curves and determine the following: a) Effective size b) Coefficient
of uniformity c) Coefficient of curvature d) Gradation of soil.
5. A sample of clay was coated with paraffin wax and its mass, including the mass of wax, was found
to be 697.5 gm. The sample was immersed in water and the volume of water displaced was found
to be 355 ml. The mass of the sample without wax was 690.0 gm, and the water content of the
representative specimen was 18%. Determine the bulk density, dry density, void ratio and the
degree of saturation. The specific gravity of the solids was 2.70 and that of the wax was 0.89.
6. A sample of soil with Liquid Limit of 72.8% was found to have a liquidity index of 1.21 and water
content of 81.3%. Find plastic limit and plasticity index.
7. Two soil C and D are mixed dry in proportion of 35%, 65% by mass. The specific gravity of soil
C and D are 2.65 and 2.75 respectively. If the bulk density of mixed soil is 1.7 gm/cc at 15% water
content, determine void ratio and degree of saturation.
8. In a test to determine the liquid limit of silty clay the following results were recorded.
Mass of container with wet 19.62 21.26 19.5 21.28
soil (gm)
Mass of container with dry 16.74 18.39 17.24 19.08
soil (gm)
Mass of container (gm) 10.46 11.21 10.87 11.62
Number of blows (N) 12 19 28 41
Plot the result in graph paper and determine the liquid limit for the soil. If the plastic limit for the
soil was 22% and natural water content 35%, find the plasticity index, liquidity index and
consistency index.

Compiled By: Abhash Acharya 3

9. A natural soil deposit has a bulk unit weight of 17 KN/m3 and water content of 10%. Determine the
amount of water required to be added to 1m3 of soil to raise the water content to 15%. Assume void
ratio remains constant.
10. Earth is required to be excavated from a borrow pit for building an embankment. The unit weight
of undisturbed soil in wet condition is 18KN/m3, and its water content is 9%. In order to build a 4
m high embankment with top width 3m and side slope 2:1 (H:V), estimate the quantity of earth
required to be excavated for 1m length of embankment. The dry unit weight of embankment is 15
kN/m3, with moisture content of 12%. Assume specific gravity of solids as 2.65.
11. For a soil in natural state, given e = 0.8, w = 24% and Gs = 2.68. Determine the moist unit weight,
dry unit weight and degree of saturation. If the soil is made completely saturated by adding water,
what would be its moisture content at that time? Also find saturated unit weight. Notations have
their usual meanings.
12. The liquid limit and shrinkage limit of a soil sample are 50% and 16% respectively. If the volume
of the specimen of this soil decreases, on drying from 37.2cm3 at liquid limit to 22.4cm3 at
shrinkage limit, compute the specific gravity of soil particles.
13. A pycnometer weighing 640gms was used in the following measurement on sample A and B of the
same soil. Sample Aa was oven dried and B was completely saturated. Weight of pycnometer when
filled with water was only 1495 gms.
Samples A B
Wt. of sample only (gms.) 1000 1344
Wt. of pycnometer full of soil sample and water 2125 2200
Find i) The specific gravity of soil and
ii) The water content and void ratio of sample B.
14. A soil sample was collected in a sampling tube of internal diameter 5cm and length 12cm. The
weight of extracted sample was 420gms. On oven drying its weight was 380gms. Assume the
specific gravity of soil grains to be 2.7. Determine:
i) Bulk Unit Weight.
ii) Water Content.
iii) Void ratio.
iv) Degree of saturation.
15. In an oil drilling project, a heavy viscous liquid (drilling mud) was used to keep the drilling hole
open. It consists of suspension in water of the following properties per litre of volume.
380gm of clay of G = 2.82
82gm of sand of G = 2.68
300gm of iron fillings of G = 7.13
Assuming that unit weight of water = 1.00 gm per cc and a uniformly mixed suspension, what is
the unit weight of suspension?
16. Soil is to be excavated from a borrow pit which has a density of 1.75 gm/cc and water content of
12%. The specific gravity of soil particles is 2.7. The soil is compacted so that water content is 18%
and the dry density is 1.65 gm/cc. For 1000 cu.m. of soil in the fill estimate:
• The quantity of soil to be excavated from the pit in cu.m.
• The amount of water to be added.
Also determine the void ratio of the soil in borrow pit and fill.
17. A test for the determination for the liquid limit was carried on a soil sample. The following sets of
observations were taken. Plot the flow curve and determine the liquid limit and the flow index.

Compiled By: Abhash Acharya 4

 No. of blows (N) 38 27 20 13
Water Content 47.50 49.50 51.90 53.90
(W%)
18. Classify the soils A and B with the properties as shown below, according to USC System.
Soil LL (%) Ip (%) % Passing No. 4 Sieve % Passing No. 200 Sieve
A 45 29 100 59
B 55 15 100 85

19. The sieve analysis of a given sample of soil gave information that 65% of the particle pass through
75-micron sieve. The following data has been obtained from liquid and plastic limit tests on the
soil in the laboratory.
Details Liquid Limit Test Data Plastic Limit
Mass of container with wet soil, 43.35 47.5 45 44.95 43.62 40.38
(g)
Mass of container with dry soil, 40.18 43.61 41.87 41.5 41.94 38.85
(g)
Mass of container only, (g) 29.86 31.5 32.05 30.51 33.1 30.9
Number of blows (N) 34 27 23 17
Determine:
i) Liquid limit, Plastic limit and flow index.
ii) Classify the soil as per the Unified Soil Classification System.
iii) Liquidity index if the natural water content of the soil is 30%.

20. Find the group index value according AASTHO soil classification system by using following data.
% passing 75-micron sieve = 58%, Liquid limit = 50%, Plastic Limit = 35 %.
21. The sieve analysis of a given sample of soil gave information that 60% of the particle pass through
75 micron sieve. The liquid and plastic limit of the soil were 62 and 28 percent respectively.
Classify the soil as per USCS.
22. The sieve analysis of a given sample of soil gave information that 55% of the particle pass through
75-micron sieve. The liquid and plastic limit of the soil were 58 and 26 percent respectively.
Classify the soil as per USCS.

23. Two soils were tested for their consistency in the lab. The following data were obtained.
Soil A Soil B
No of blows (N) Water Content (%) No of blows (N) Water content (%)
8 43 5 65
20 39 15 61
30 37 30 59
45 25 40 58
Water content at 25% Water content at 30%
which soil crumbled which soil crumbled
of 3mm diameter. of 3mm diameter.
Natural Water 40% Natural Water 50%
Content Content
Determine:
i) Which soil has greater plasticity?
ii) Which soil is more compressible in nature?
iii) Classify the both soils as per IS Classification System.

Compiled By: Abhash Acharya 5

24. A sample of soil was tested in a laboratory, and the following observations were recorded.
Liquid Limit = 45 %
Plastic Limit = 16 %
U.S. Sieve No. No. 4 No. 10 (2.0 mm) No. 40 (0.425 mm) No. 200 (0.075 mm)
Percentage Passing 100 91.5 80 60
Classify the soil according to AASHTO System.
25. Mechanical analysis on four different sample designated as A, B, C and D were carried out in a soil
laboratory. The results of tests are given below. Hydrometer analysis was carried out on sample D.
Soil is non-plastic.
Sample D: Liquid Limit = 42, Plastic Limit = 24, Plasticity Index = 18
Classify the soil as per the Unified Classification System.
Samples ASTM A (% finer B (% finer C D
Sieve than) than)
Designation
63 mm 100 93
20 mm 64 76
6.3 mm 39 100 65
2.0 mm 24 98 59
600 µ 12 90 54
212 µ 5 9 47 100
63 µ 1 2 34 95
20 µ 23 69
6µ 4 46
2µ 7 31

26. The following are the results of a compaction test.

Mass of mould + wet 2925 3095 3150 3125 3070
soil (g)
Water content (%) 10.0 12.0 14.3 16.1 18.2
Volume of mould = 1000 ml, Mass of mould = 1000 gm. Specific gravity of solids = 2.70.
i) Draw the compaction curve showing Optimum Moisture Content (OMC) and Maximum
Dry Density.
ii) Plot the zero-air void line.
iii) Determine the degree of saturation at maximum dry density.
27. Given standard soil compaction test results as follows:
Trial No. Moisture Content (% by dry Wet unit weight of
weight) compacted soil (KN/m3)
1 8 19
2 10 21.2
3 11.4 21.9
4 12.6 21.1
5 13.9 20.2
The specific gravity of the soil particles is 2.65. Plot the following:
a) Moisture-dry density curve.
b) Zero air voids curve and
c) Ten percent air content curve (90% saturation curve).

Compiled By: Abhash Acharya 6

28. The following data refers to a compaction test.
Water 8.5 12.2 13.75 15.5 18.2 20.2
content (%)
Weight of 1.8 1.94 2.00 2.05 2.03 1.98
wet sample
(kg)
If the specific gravity of soil grains was 2.7.
i) Plot the compaction curve and obtain the maximum dry unit weight and the OMC.
ii) Plot the 80% and 100% saturation lines.
iii) If it is proposed to secure a relative compaction of 95% in the field, what is the range of
water content that can be allowed.
iv) Would the 20% air voids curve be the same as the 80% saturation curve.
29. A sample of soil is prepared by mixing a quantity of dry soil with 10% by mass of water. Find the
mass of this wet mixture required to produce a cylindrical compacted specimen of 15cm diameter
and 12.5cm deep and having 6% air content. Find also the void ration and the dry density of the
specimen if G = 2.68.
30. The following results were obtained from standard compaction test:
Mass of compacted 1929. 2051.5 2138. 214 212 205
soil (gm) 5 5 7 8 8
Water content (w %) 11 12.4 12.9 13.8 14.9 16.7
The specific gravity of soil solids is 2.65, and the vol. of mould is 1000cm3. Plot the compaction
curve and obtain the maximum dry density and optimum moisture content. Plot also 0%, 5%, 10%
air voids curves. At the maximum dry density, calculate the void ratio, degree of saturation and air
content.
31. The following results were obtained from the sand replacement method:
Mass of soil extracted from the hole 4.0 kg
Water content of soil 18%
Mass of dry soil to fill the hole 3.1 kg
Mass of dry sand to fill container of volume 4.2 liters 5.8 kg
Calculate the wet and dry densities of the soil. If the specific gravity of the particles is 2.68, find
the degree of saturation of the soil.
32. The insitu density of an embankment, compacted at a water content of 12% was determined with
the help of core cutter. The empty weight of the cutter was 1286 gm and the cutter full of soil had
a weight of 3195 gm, the volume of the cutter being 1000 cm 3. Determine the bulk density, dry
density and the degree of saturation of the embankment. If the embankment becomes fully saturated
during rains, what would be its water content and saturated unit weight? Assume no volume change
in soil on saturation. Take the specific gravity of the soil as 2.7.
33. A laboratory constant head permeability test was conducted on a silty specimen of void ratio 0.45.
The cylindrical specimen had a diameter of 7.3 cm and height of 16.8 cm. The head during the test
was 75 cm. After 1 minute of testing at room temperature, a total of 775.6 gm of water was
collected. Determine coefficient of permeability of soil. If void ratio changes to 0.38, What would
be the percentage change in permeability?
34. In falling head permeameter test, the initial head (t=0) is 40 cm. The head drops by 5 cm in 10
minutes. Calculate the time required to run the test for the final head to be at 20 cm. If the sample
is 6 cm in height and 50 cm2 in x-sectional area, calculate the coefficient of permeability, taking
area of stand pipe as 0.5 cm2.

Compiled By: Abhash Acharya 7

35. The capillary rise in soil A with D10 = 0.06 mm is 60 cm. Estimate the capillary rise in soil B with
D10 = 0.1 mm. Assume the same void ratio in both the soils.
36. A 3 m thick soil stratum has a coefficient of permeability of 3*10-7 m/sec. A separate test gave
porosity 40% and bulk unit weight 21KN/m3 at a moisture content of 31%. Determine the head at
which upward seepage will cause quick sand condition. What is the flow required to maintain
critical condition?
37. Calculate the coefficient of permeability of soil sample 8 cm height and cross-sectional area 60
cm2. It is observed that in 12 minutes, 600 ml of water passed down under constant head of 50 cm.
The test specimen weighs 750 gm in dry condition. Take specific gravity of soil solids as 2.7.
Calculate the seepage velocity.
38. A fine sand deposit is located between the ground surface to a depth of 10 m. The soil has an
average void ratio of 0.70 and a specific gravity of 2.65. The water table is found at a depth of 4 m
below the ground surface. Above the water table the degree of saturation of sand is 55 %. Determine
the total stress, pore water pressure and effective stress at a depth of 8 m below the ground surface.
Calculate also the change in the effective stress if the soil gets saturated upto a height of 1 m above
the water table due to capillary.
39. A sand deposit consists of two layers. The top layer is 3m thick (ρ=1800 kg/m 3) and the bottom
layer is 3.5m thick (ρsat = 2500 kg/m3). The water table is at a depth of 4m from the surface and
zone of capillary saturation is 1 m above the water table. Draw the diagram showing the variation
of total stress, neutral stress (pore water pressure) and effective stress.
40. A horizontal stratified deposit consists of 3 layers with coefficient of permeability as 8*10-4 cm/sec,
50*10-4 cm/sec and 15*10-4 cm/sec and their thickness are 6m, 3m and 18m respectively. Find the
effective average permeability of the deposit in horizontal and vertical direction.
41. In order to determine the average coefficient of permeability of a bed of sand 14 meters thick,
overlying an impervious stratum, a well was sunk through the sand and a pumping test was carried
out. After a certain interval, the discharge was 12.4 liters per second and drawn down in the
observation wells at 16 meters and 33 meters respectively from the test well were found to be 1.787
m and 1.495 m respectively. If the GWT was originally 2.14m below the ground surface, find a)
the permeability of sand layers, b) an approximate value for the effective grain size. (Take C =
125).
42. A layer of sand 6m thick lies beneath a clay stratum 5m thick and above a thick shale. In order to
determine the permeability of the sand, a well was driven to the top of the shale and water was
pumped out at the rate of 10*10-3 m3/secs. Two observations well were driven through the clay at
15m and 30m from the pump well and drawn down in the wells were found to be 3m and 2.5m
respectively. Calculate the coefficient of permeability of the soil.
43. A sand layer 10m thick overlies an impervious stratum. The water table is in the sandy layer at a
depth of 1.5m below the ground surface. Water is pumped out from a well at the rate of 100 litres
per second and the drawdown of the water table at a radial distance of 3m and 25m is 3m and 0.5m
respectively. Determine the coefficient of permeability.
44. A 12m thick layer of relatively impervious stratum of clay lies over a bed of gravel aquifer.
Piezometer tubes introduced to the level standing in the tubes 3 m above the top surface of the clay
strata. The properties of the clay soil are e = 1.2 and G = 2.7. Determine: the effective stress at the
top level of the gravel strata, the depth of excavation that can be made in the clay strata without the
bottom heave.
45. A pumping test was made in a medium sand having depth of saturation 20m, where a bed of clay
was encountered. The normal ground water table was at the surface. Observation wells were located

Compiled By: Abhash Acharya 8

 at 4m and 10m from the pumping well. At a discharge of 2m3/min. from the pumping well, a steady
state was obtained in 24 hrs. The draw down at 4m well was 1 m and 10 m was 0.5m. Draw neat
sketch and compute the permeability of the soil. If the draw down is 6m in the main well and dia
of the tube-well is 30cm then what is the distance between center of the well and zero draw down.
46. A concrete dam is constructed across a river over permeable strata of the soil of limited thickness.
The water head on U/S side is 16m and 2m on the D/S side. The flow net constructed under the
dam gives Nf = 7 and Nd = 21. Calculate the seepage loss through the subsoil if the average value
of coefficient of permeability is 6*10-3 cm/sec horizontally and 3*10-6 cm/sec vertically. Calculate
the exit gradient if the average length of the last field is 0.9m.
47. A sand deposit 10m thick overlies an impervious soil. A vertical sheet pile penetrates half way into
the sand deposit. The water level on one side of the wall is 3.0m and on the other side is 0.5m above
the ground level. The sand stratum has a vertical permeability of 1.44 m per day, and the horizontal
permeability equals 8 times the permeability in the vertical direction. A flow net construction
reveals that there are 12 flow channels and 26 potential drops. Determine the seepage flow per day.
48. A sheet pile wall is driven to a depth of 6m into permeable soil which extends to a depth of 13.5m
below the ground level. Below this there is an impermeable stratum. There is a depth of water of
4.5m on one side of the sheet pile wall. Make a neat sketch of the flow net and determine the
approximate seepage under the sheet pile wall in m3/day, taking the permeability of the soil as 6*10-
3
mm/secs.
49. Determine the co-ordinates of the phreatic line for the earth dam having top width=10m, Height of
earth dam =35m, side slope = 2.5:1 (H:V), water height in U/S side =30m, water height at D/S
surface =0, length of filter from toe =60m . Draw phreatic line and determine discharge through
earth dam.
50. A soil stratum with permeability k = 5*10-7 cm/sec overlies an impermeable stratum. The
impermeable stratum lies at a depth of 18m below the ground surface (surface of soil stratum). A
sheet pile wall penetrates 8m into the permeable soil stratum. Water stands to a height of 9m on
upstream side and 1.5m on downstream side, above the surface of soil stratum. Sketch the flownet
and determine:
i) Quantity of seepage.
ii) The seepage pressure at a point ‘p’ located 8m below surface of soil stratum and
4m away from the sheet pile wall on its upstream sides.
iii) The pore pressure at point ‘p’ and
iv) The maximum exit gradient.
51. A soil deposit consists of three horizontal layers of isotropic soils. The thickness of the top, middle
and bottom layer is 3m, 4m and 5m respectively while the corresponding coefficient of permeability
is 0.3*10-3 cm/sec, 0.4*10-3 cm/sec and 0.5*10-3 cm/sec respectively.
a. Determine the average (or equivalent) coefficient of permeability if the flow is parallel to
the bedding plane and if it is perpendicular to the bedding planes.
b. If a concrete dam is to be constructed on the above soil deposit, what scaling adjustment
has to be made before the construction of flownet? Draw sketch to clarify your answer.
What will be the equivalent isotropic coefficient of permeability of the soil deposit?

Compiled By: Abhash Acharya 9

 Numerical

1. The plan of a foundation is shown in figure. The uniform pressure on the soil is 45KN/m2. Determine the vertical stress
increment due to the foundation at a depth of 4m below the point A. (2019 Fall)

2. A water tank is supported by a ring foundation having outer diameter of 10m and inner diameter of 7.5m. The ring
foundation transmits uniform load intensity of 160KN/m2. Compute the vertical stress induced at a depth of 4m below the

centre of ring foundation using

a. Boussinesq analysis
b. Westergaard’s analysis (Take v=0.25) (2016 Fall)

3. A point load of 170 KN is applied at the ground surface. Construct the pressure bulb when the stress imposed becomes 25%
of the applied load. (2016 Spring)
4. A raft foundation of 8m dia is placed on the ground surface and carries a load of 10000KN including self weight. Calculate
the vertical stress increment at the centre of clay layer using Boussinesq’s theory. The clay layer is 2m thick and it exists 5m
below the ground surface. (2012 Fall)
5. A point load of 1200 KN is applied at the ground surface. Construct the stress contour when the stress imposed becomes 25%
of the applied load. (2017 Fall)
6. A concentrated point load of 250KN acts at the ground surface. Find the intensity of vertical pressure at a depth of 5m below
the ground surface at the point on the axis of loading using Boussinesq analysis. What will be the difference in vertical
pressure at the same point if the load is shifted to a distance of 2m from its original position horizontally?
(2015 Fall)
7. A ring footing of external diameter 8m and internal diameter 4m rests at a depth of 2m below the ground surface. It carries a
load intensity of 150KN/m2. Find the vertical stress at depths 2m and 4m along the axis of footing base. Neglect the effect of
excavation on the stress. (2014 Fall
8. A water tower weighing 20000KN is to be considered as concentrated load acting on the ground surface. Compute the
vertical stress at a depth 10m below the surface. Also compute the vertical stress at a distance of 8m away from the centre of
water tower. (2015 Spring)
9. The plan of a three-legged tower forms an equilateral triangle of side 6m. If the total weight of the tower is 8000 KN and
equally carried by all the legs. Compute the increase in vertical stress in the soil by the tower at a depth of 4.5m directly
below the centre of equilateral triangle. (2012 Spring)

10. A ring footing of external dia 8m and internal dia 4m rests at a depth 2m below the ground surface. It carries a load intensity
of 150KN/m2. Find the vertical stress at a depth of 2m and 4m along the axis of footing base. Neglect the effect the
excavation on the stress. (2014 Fall) (2011 Spring) (Ans: 36.63 KN/m2 at depth 2m and 54.29 KN/m2 at a
depth 4m)

Soil Mechanics UESC Prepared By: Sandesh Ghimire

 11. Two columns A and B are placed at 5m centre to centre. Through point A, a load of 400 KN is acting and from point B a load
of 240KN. Calculate the vertical stress due to these loads on a horizontal plane 2m below the ground surfaces at points:
a. Vertically below the points A and B
b. 10m horizontally away from point A (2008 Fall)
(Ans: a. 48.56 KN/m2, 28.98 KN/m2 b. 0.015 KN/m2)
12. Using Fadum’s chart, determine the increase in vertical stress at 2m depth below A and B due to UDL of 40 KN/m2 on the
ground surface shown by the area in fig2. (21.02 KN/m2, 8.98 KN/m2) (2009Fall)
13. Find the vertical stress at 5m below point P due to UDL hatched area of 300 KN/m2 intensity as shown in fig 6.
(2.37 KN/m2) (2014 Fall)
Additional Probable Questions
14. A point load of 1000 kN acts at a ground surface. Show the variation of vertical stresses on a horizontal plane at a depth of
5m below the surface.
15. A water tank in three pillars is in the form of an equilateral triangle in plan and the sides of the triangle are 10 metres. The
total weight of water tower is 1000KN. Find the vertical stress 10m below the ground surface under any one of the legs.
16. A water tower has a circular foundation of diameter 9m. The total weight of the tower including the foundation is 17500KN.
A very weak foundation capacity of 95KN/m 2 lies 3m below the foundation level. Calculate the stress due to foundation at
the top of water stratum. Give your comment with regard to the feasibility of foundation construction at the top surface of the
weak layer.
17. A concentrated load 800KN acts at the ground surface. Compute the vertical stresses at 8m depth:
a. On the axis of load
b. 2 m away from axis. Use Westergaard’s analysis taking v=0.25.
(Ans: 5.98 KN/m2, 4.62 KN/m2)
18. The load from a continuous footing of width 2m, which may be considered to be a strip load of considerable length, is 200
KN/m2. Determine the vertical stress at 1.5m below the footing if the point lies directly below the centre of footing. (Ans:
133.42 KN/m2)
q
(hint σ: π(2θ+sin2θ) (θ = tan-1(b/z)) (b=B/2)
19. A strip footing of width 2m carries a load of 400KN/m. calculate the maximum stress at a depth of 5m below the centre line
of footing. Compare the result with 2:1 distribution method. (49.53KN/m2)
q
(hint σ: π(2θ+sin2θ) (θ = tan-1(b/z)) (b=B/2) where θ is in radians.
q∗B
For 2:1 method, σ=B+z
20. A foundation of a building is rectangular in plan. It carries a uniform pressure of 25KN/m2. Assuming the center of
foundation as origin and Cartesian coordinates of the corners to be (5, 10), estimate the stress at depths of 20m below the
ground surface at each of the following points: (0,10), (5,0), (5,10) and (7, 15).
21. A point load Q acts on the ground surface.
a. Show the variation of vertical stresses on a horizontal plane at a depth of 2 m below the surface.
b. Also show the variation of vertical stresses on a vertical plane at a radial distance r= 2m away from the applied load
Q on the ground surface.
22. A rectangular foundation 2m * 1.5m carries a uniform load of 40 KN/m 2. Determine the vertical stress at P which is 3m
below the ground surface as shown in fig5. Use equivalent point load method.
23. Two UDL of rectangular pattern with different load intensity are placed side by side on the ground as shown in the figure 4.
Determine the vertical pressure due to the load below point A and B at a depth of 6m.(4.08 KN/m2, 3.102 KN/m2)
24. A UDL ABCDEF having a plan area as shown in fig 3 is placed on the ground surface. The intensity of load is 20 KN/m2.
Determine the increase in vertical stress due to the load at 6m depth below the corner points C and D. (4.91 KN/m2, 3.112
KN/m2)
25. A strip footing is given in plan as shown in fig 1. The total load per unit area is 300 KN/m2. Determine the intensity of
vertical stress at a point 5m directly below the point A. (9.55t/m2)
26. Determine the vertical stress at a depth of 4m below the raft foundation having size 20m*15m and the load on the raft is
30000KN. The depth of foundation is 3m and unit weight of soil is 17KN/m 3. The number of area units on Newmark chart is
105 if If =0.005. Also check the safeness of footing if bearing capacity of soil is 28KN/m2. (Hint: σ= qnet*If*No. of area units,
Q
qnet= ( − γ ∗ Z) (Ans: 27.7KN/m2, Unsafe)
A

Soil Mechanics UESC Prepared By: Sandesh Ghimire

 27. A rectangular area 4m*2m is uniformly loaded with a load intensity of 100 KN/m2 at a ground surface. Determine the vertical
pressure at a depth 3m below a point within the loaded area 1m away from the short edge and 0.5m away from long edge.
Use equivalent point load method. (25.37 KN/m2)
28. A raft foundation of 12m dia is placed on the ground surface and carries a load of 8000KN including self weight. Calculate
the vertical stress increment at the centre of clay layer using Boussinesq’s theory. The clay layer is 2m thick and it exists 7m
below the ground surface.
29. The plan of a three-legged tower forms an equilateral triangle of side 7m. If the total weight of the tower is 6000 KN and
equally carried by all the legs. Compute the increase in vertical stress in the soil by the tower at a depth of 3.5m directly
below the centre of equilateral triangle.
30. A ring footing of external diameter 6m and internal diameter 2.5m rests at a depth of 2m below the ground surface. It carries
a load intensity of 150KN/m2. Find the vertical stress at depths 2m and 4m along the axis of footing base. Neglect the effect
of excavation on the stress.
31. A water tower weighing 15000KN is to be considered as concentrated load acting on the ground surface. Compute the
vertical stress at a depth 10m below the surface. Also compute the vertical stress at a distance of 6m away from the centre of
water tower.

32. A clay layer has a thickness of 5m and is subjected to a pressure of 60KN/m2. If the layer has a double drainage and
undergoes 50% consolidation in 1 year, determine the coefficient of consolidation taking T v= 0.197. Also if the coefficient of
permeability is 0.025m/year, determine the settlement in 1 year and rate of flow of water per unit area in 1 year. (2013 spring)
33. A stratum of clay is 2m thick and has an initial overburden pressure of 50KN/m 2 at its middle. Determine the final settlement
due to an increase of 40KN/m2 at the middle of the clay layer. The clay is over consolidated with a preconsolidation pressure
of 75KN/m2. The values of coefficient of recompression and compression index are 0.05 and 0.25 respectively. Take initial
void ratio as 1.40.(Ans: 23.84mm) (2009 spring)
34. The consolidation settlement of a new structure founded on a 5m thick layer is estimated as 6.5cm. The structure was
observed to have settled by 1.6cm in six months after the completion of construction. If the clay layer is underlain by rock
and overlain by a layer of coarse sand. Determine :
a. The time required for 50% consolidation
b. The amount of settlement which will take place in the next six months. (2012 Fall)
35. A saturated soil stratum 5m thick lies above an impervious stratum and below a pervious stratum. It has a compression index
of 0.3 and coefficient of permeability of 3.2*10-4cm/sec. it has a void ratio of 0.5 at a stress of 1.4kg/cm2. Compute:
a. The void ratio if the stress is increased to 2kg/cm2
b. Settlement of soil stratum due to above increased stress
c. Time required for 80% consolidation. (2015 Fall)(2008 Fall DH)
36. A sand layer 5m thick lies over a clay layer 3.0m thick. The clay has saturated unit weight of 19KN/m3 and has a
compression index of 0.22. The initial void ratio of clay is 1.2. Calculate the final settlement of clay layer due to an increase
in pressure of 35KN/m2 at the centre of clay layer. Also calculate the settlement when the water table rises to the ground
surface. (2015 spring) (2014 Spring) (2011 Fall)
Soil Mechanics UESC Prepared By: Sandesh Ghimire
 37. A saturated soil stratum 6 metres thick lies above an impervious stratum and below a pervious stratum. It has a compression
index of 0.28 and a coefficient of permeability of 3.5×10 -4 cm/sec. Its void ratio at a stress of 150 kN/m2 is 1.95. Determine:
i) The change in void ratio due to an increase in stress to 210 kN/m 2.
ii) Settlement of the soil stratum due to the above increase in stress.
iii) Time required for 50 percent consolidation.
Assume time factor T for 50 percent consolidation as 0.20.
37.

38. Find the time required for 50% and 80% consolidation in a soil stratum, 10m thick with a pervious stratum on top and
bottom. Also find the coefficient of consolidation if, K=1*10 -9m/s, eo= 1.5 and av= 0.003 m2/KN. Symbols have their usual
meanings. (667.625days, 1931.7 days, Cv=8.497*10-8m2/sec) (2016 Fall)
39. A consolidation test was performed on a 25mm thick undisturbed clay sample, 50% consolidation occurred in 5minutes. In
the field, a clay layer is 2m thick and underlain by rock stratum. There is a sand layer above the clay layer. Determine the
coefficient of consolidation. Also compute the number of days required for the field stratum to reach 50% consolidation.
(2009 Spring)
40. Two clay samples A and B have initial void ratio of 0.55 and 0.632 respectively under pressure of 100KN/m 2. The pressure
increased to 150 KN/m2. With the application of pressure, the void ratio decreases to 0.495 and 0.616 respectively. The time
taken by sample A to reach 50% consolidation one third of the time required by sample B to reach the same consolidation.
Find the ratio of coefficient of permeability of the specimen A and B if their thickness was 40 mm and 30 mm respectively.
( 19.3:1)
41. A 5m thick sand layer underlies a consolidated clay layer of 1m thickness. The water table is located on the ground surface.
A 2m high soil embankment is laid on the ground surface in circular pattern having a diameter of 20m. The bulk unit weight
of embankment sand and soil 17.5KN/m3 and 19 KN/m3. The clay has a bulk unit weight of 17.5 KN/m 3, void ratio of 2.6 and
compression index of 0.5. Calculate the settlement of clay layer beneath the center of embankment. (36.23mm)
42. A stratum of normally consolidated clay of thickness 3m is drained on both sides. If it has a coefficient of permeability k=
5*10-8cm/sec and coefficient of volume compressibility 125*10 -2cm2/KN. Determine the total compression of the strata for a
change in stress of 25t/m2. Also determine the time required for 80% consolidation. (9.4cm, 36.9 days)
43. A soil deposit consists of upper layer of sand 6m thick underlain by a normally consolidated clay layer of 1m thick. The
water table is 2m below the ground surface. Calculate the settlement of the clay if 1.5m thick backfill soil is dumped on the
ground surface covering large area. The unit weight of the backfill is 18.5 KN/m 3 while that of the sand deposit is 18 KN/m3.
The clay soil has a bulk unit weight of 17.5 KN/m3 and initial void ratio equal to 2.20. The compression index is 0.40.
(17.75mm)
44. A clay layer of 1m thick is found between 6m and 7m below the ground surface. The clay layer is sandwiched between sand
layers. The coefficient of volume change of clay is 0.40*10-3m2/KN. A 3m high sand embankment of circular plan area of
diameter 20m is placed on the ground surface. The unit weight of the sand is 20KN/m 3. Determine the settlement of the clay
layer under the center of the circular shape of radius r which can be calculated using the given formula
1
∆σ = (1 − ( r )1.5)*q
1+( )
z
45. A 4m clay layer beneath a structure is underlain by rock and overlain by sand. The coefficient of consolidation of the clay
was found to be 0.02cm2/min. The expected final settlement of the layer was 15cm. Determine the time taken for settlement
of 5cm. How much time will it take for 80% final settlement to occur? (484.72 days, 3150days)
46. A soil deposit consists of a sand layer up to a depth of 5m underlain by a clay layer of 2m thickness. Water table was initially
at ground surface but is lowered permanently by 2m. Determine the settlement at the centre of clay if the coefficient of
volume compressibility is 0.25*10-3m2/KN. (3.9cm)
47. A saturated clay stratum 4m thick lies above an impervious stratum and below a pervious stratum. It has a void ratio of 1.2 at
an initial pressure of 200KN/m2. Compute the change in void ratio due to an increase in stress of 50 KN/m 2 assuming the soil
is normally consolidated with compression index 0.2. What would be the time required for 50% consolidation? Take
coefficient of permeability =3*10-4cm/s. (29.67min)
48. A certain clay layer has a thickness of 5m. After 1 year, when the clay was 50%consolidated, 8cm of settlement had occurred.
For similar clay and loading conditions, how much settlement would occur at the end of 1 year and 4 years respectively if the
thickness of this new layer was 25m? (8cm, 16cm)
49. A compressible layer whose total settlement under a given loading is expected to 20cm settles 4cm at the end of 2 months.
How many months will it take to reach the settlement of 10cm? Assume double drainage. (12.5 months)

Soil Mechanics UESC Prepared By: Sandesh Ghimire

 50. A 25mm thick clay sample was used in oedometer consolidation test. During test it takes one month for 50% consolidation. If
the same clay of 5m thickness is in between rock layer and sand layer in site, calculate the time required for 90%
consolidation in site after construction of building in site. (692800 months)
51. A stratum of clay is 2m thick and has an initial overburden pressure of 50KN/m 2 at its middle. Determine the final settlement
due to an increase in pressure of 40KN/m2 at the middle of clay layer. The clay is overconsolidated with a preconsolidation
pressure of 75KN/m2. The values of the coefficient of recompression and compression index are 0.05 and 0.25 respectively.
Take initial void ratio as 1.4. (23.84mm)

52. Following data were obtained from consolidation tests on two specimens A and B.
Equilibrium Void Ratio
Pressure (KN/m2)
A B
100 0.535 0.63
150 0.48 0.615
The initial thickness of specimen A was 30mm and that of B was 20mm. if the time taken for specimen A to reach 50%
consolidation is one third of the time required by specimen B to reach the same degree of consolidation, find the ratio of
coefficient of permeability of the two clay specimens. (KA : KB = 26.28 : 1)
53. A consolidation undrained test was conducted on a clay sample and the following test results were obtained:
Cell Pressure (KN/m2) 200 400 600
Deviator stress at failure (KN/m2) 118 240 352
Pore water pressure at failure(KN/m2) 110 220 320
Determine the shear strength parameters with respect to
a) Total stresses.
b) Effective stresses.
54. A soil sample was tested on lab by direct shear box test on a remoulded sand sample revealing the following information at
the time of failure
Normal load =0.9KN
Shear load = 0.45 KN
Sample area= 36 cm2
Determine:
a. The angle of internal friction
b. The magnitude and direction of principal stresses in the zone of failure. (2012 spring) (2012 fall) (2016 Spring) (2017
Fall)
55. A specimen of clean sand when subjected to direct shear test failed at a stress of 120KN/m 2 when the normal stress intensity
was 160KN/m2.
a. Determine the angle of internal friction
b. Deviator stress at which the failure will take place if a cylindrical sample of the same sand is subjected to a cell pressure
of 100KN/m2. Also find the angle made made by the failure plane with the horizontal. ( ∅ = 35°, c = 300, ∅ =
63.45°) (2014 spring)
56. An unconfined cylindrical specimen of clay fails under an axial stress of 240 KN/m 2. The failure plane was inclined at an
angle of 55 degrees to the horizontal. Determine the shear strength parameters of soil. (2014 Fall)
57. A direct shear test was conducted on a soil sample with cohesion of 10KN/m 2. The cross sectional area of sample was 60mm
by 60mm. The normal load applied to the sample was 0.72KN. Determine:
a. The friction angle of soil if the shear load is 0.42KN
b. The shear force at failure if the same soil is subjected to a normal load of 1.44KN. (2015 Fall)
58. A consolidation undrained test was conducted on a clay sample and the following test results were obtained:
Cell Pressure (KN/m2) 200 400 600
Deviator stress at failure (KN/m2) 118 240 352
Pore water pressure at failure(KN/m2) 110 220 320
Determine the shear strength parameters with respect to
a. Total Stresses
b. Effective Stresses (2015 Spring)
59. A consolidation undrained test was conducted on a clay sample and the following test results were obtained

Soil Mechanics UESC Prepared By: Sandesh Ghimire

 σ3 (KN/m2) 150 300 450
σ1 − σ3 (KN/m2) 192 341 504
U (KN/m2) 80 154 222
Determine the shear strength parameters with respect to
a. Total Stresses
b. Effective Stresses (c=16kg/cm2, ∅ = 29°) (2011 Fall)
60. A sample of dry coarse soil is tested in the laboratory triaxial apparatus in the undrained condition under the cell pressure of
2kg/cm2. The sample failed when the deviator stress reached 4.38 kg/cm 2. Determine the shear parameters of the soil. At
what deviator stress will soil fail if the cell pressure be 3kg/cm 2? (2016 Fall)

61. The sand deposit in the field has an angle of shearing resistance of 34 degrees, dry density of 17KN/m3, moist unit weight of
18KN/m3 and saturated unit weight of 20KN/m3. The water table is 1.5m below G.L. The sand is dry up to 1m depth and
moist between 1 m and 1.5m depth. What is the shearing resistance on sand on a horizontal plane at a depth 2.5m below
G.L.? (2010 spring)
62. A sample of dry cohesionless soil was tested in triaxial machine. If the angle of shearing resistance was 36 degrees and
confining pressure was 100 KN/m2, determine the deviator stress at which the sample failed. (2017 Spring)
63. The sand deposit in the field has an angle of shearing resistance of 34°, dry density of 17 KN/m3, moist unit weight of
18KN/m3 and saturated unit weight of 20KN/m3. The water table is 1.5m below G.L. The sand is dry up to 1m depth and
moist between 1m and 1.5m depth. What is the shearing resisting on sand on a horizontal plane at 2.5m depth below G.L.?
(2012 Spring, 2010 Spring)
64. A direct shear box test performed on a remoulded sand sample yielding the following observations at the time of failure:
Normal load= 0.36KN
Shear load= 0.18KN
Sample area= 36cm2. Determine:
a. Determine the angle of internal friction
b. The magnitude and direction of principal stresses in the zone of failure
c. The magnitude of deviator stress of the sample of same sand with same void ratio were tested in a triaxial test with all
round pressure of 60KN/m2. Assume c=0. (2008 Spring) (2010 Spring) (2012 Spring)
65. A direct shear box test performed on a remoulded sand sample yielding the following observations at the time of failure:
Normal load= 0.9KN
Shear load= 0.45KN
Sample area= 36cm2. Determine:
a. The angle of shearing resistance.
b. Angle which the failure plane makes with major principal axis.
c. The magnitude and direction of principal stresses in the zone of failure
d. Deviator stress.
66. A specimen of fine dry sand, when subjected to tri- axial compression test failed at a deviator stress of 500 KPa. It failed with
a pronounced failure plane with an angle of 25̊ to axis of sample. Compute lateral pressure to which specimen would have
been subjected.
67. In an unconfined compression test on an undisturbed sample, failure occurred under a vertical load of 12.85KN and axial
deformation at the failure was recorded as 8mm. The diameter of soil sample was 38mm and height was 75 mm. It failed
under a compressive load of 950N with a failure deformation of 12mm. Determine the unconfined compressive strength of
soil in both cases where case one is undisturbed sample and case two is remoulded. Also find the sensitivity of soil.
(1012N/cm2, 70.37N/cm2, 14.38) (2011 Spring)
68. An unconfined cylindrical specimen of clay fails under an axial stress of 240KN/m 2. The failure plane was inclined at an
angle of 55°to the horizontal. Determine the shear strength parameters of soil. (2014 Fall) (2007 SpringDH)
69. A consolidation undrained test was conducted on a clay sample and the following test results were obtained
σ3=250KN/m2
σd= 275KN/m2
Determine:
a. The angle of friction
b. Angle which the failure plane makes with the major principal plane
c. Normal stress and shear stress on the failure plane

Soil Mechanics UESC Prepared By: Sandesh Ghimire

 70. A direct shear test was carried out on a cohesive soil sample and the following results were obtained.
Case I II

Normal Stress 150 250

(kN/m2)

Shear stress at failure 110 120

(kN/m2)

What would be the deviator stress at failure if a tri-axial test is carried out on the same soil with cell pressure of 150 kN/m 2.

71. Two triaxial tests were done on a soil sample. In the first test all round pressure was 2.4kg/cm 2 and failure occurred at axial
stress of 7.5 kg/cm2. In another test all round pressure was 4kg/cm2 and failure occurred at total axial stress of 16 kg/cm 2.
Determine the values of cohesion and angle of internal friction at failure. (c=0, ∅ = 36.5)
72. An embankment is planned to be constructed from c= 4.0kg/cm2 and c= 26kg/cm2. Evaluate the shear strength of the material
on the horizontal plane at a point 10m below the surface of embankment. The bulk density of soil is 2.3gm/cc and the pore
water pressure at that point is 1.8 kg/cm2.(4.244 kg/cm2)
73. Two specimen of a soil were tested in a shear box. The following test results were obtained:
Normal load, kg 150 250
Shear stress, kg/cm2 6.0 7.5
The test was done under undrained condition. Find the apparent cohesion and angle of shearing resistance of the soil. If on
the same soil sample unconfined compresson was done, what will be the value of cohesion? The size of shear box was
5cm*5cm. (5.45 kg/cm2)
74. A consolidation undrained test was conducted on a clay sample and the following test results were obtained
Confining pressure (kg/cm2) 2 4
Deviator stress at failure(kg/cm2) 5 9
Determine the shear strength parameters c and ∅ of the soil. (∅ = 30°, c = 0.29kg/cm2)
75. In a triaxial shear test conducted on a soil sample having cohesion of 12 KN/m2 and angle of shear resistance of 36°, the cell
pressure was 200KN/m2. Determine the value of deviator stress at failure. (617.46KN/m2)
76. In a vane shear test conducted in a soft clay deposit failure occurred at a torque of 42 Nm. Afterwards the vane was allowed
to rotate rapidly and the test was repeated in the remoulded soil. The torque at failure in the remoulded soil was 17Nm.
Calculate the sensitivity of soil. In both cases the vane was pushed completely inside the soil. The height of vane and
diameter across blades are 100mm and 80mm respectively. (0.033N/mm2, 0.013N/mm2, 2.54)
77. Two clay samples A and B have initial void ratio of 0.55 and 0.632 respectively under pressure of 100KN/m 2. The pressure
increased to 150 KN/m2. With the application of pressure, the void ratio decreases to 0.495 and 0.616 respectively. The
time taken by sample A to reach 50% consolidation one third of the time required by sample B to reach the same
consolidation. Find the ratio of coefficient of permeability of the specimen A and B if their thickness was 40 mm and 30 mm
respectively.
78. A slope inclined at 16° to the horizontal to be made in cohesionless deposit having the following properties
G= 2.70 e= 0.72 ∅ = 35°
Determine the factor of safety of slope against shear failure if water percolates in a direction parallel to the surface. (1.214)
(2009 Fall)
79. A long natural slope in an overconsolidated clay (ϓ sat = 20KN/m3 C’=10KN/m2 and ∅ = 25° ) is inclined at 10° to the
horizontal. The water table is at surface and seepage is parallel to the slope. If a plane of slip had developed at a depth 5m
below the surface, determine FOS. Take unit wt of water= 10KN/m 3. (1.93) (2008 Fall)
80. A temporary cutting of 8m deep is to be made in a clay having an unit weight of 18KN/m3 and an average cohesion of
20KN/m2. A hard stratum rock exists at a depth of 12m below ground surface. Use Taylor stability chart to estimate the
safety of 30° slope.
If FOS of 1.25 is considered necessary, find the safe slope angle.
( For Df=1.5 and i=35°, Sn= 0.163)
( For Df=1.5 and i=12°, Sn= 0.11) (2013 Spring)
81. An embankment 10m high is inclined at an angle 35° to the horizontal. A stability analysis by the method of slice gave the
following force per unit length
Soil Mechanics UESC Prepared By: Sandesh Ghimire
 ∑Shearing force = 440KN
∑Normal force= 880KN
∑Neutral force = 200KN
The length of failure arc is 26m. laboratory tests on soil indicated the effective values of C and ∅ as 20 KN/m2 and 18°
respectively. Determine FOS of slope with respect to
a. Shearing strength
b. Cohesion (1.68, 1.8) (2018 Fall)
82. An infinite slope is made of clay with following properties
ϓ sat = 18KN/m3
ϓ′ = 9KN/m3
C = 25N/m3
∅=28°
If the slope has inclination of 35° and height equal to 12m, determine the stability of slope when
a. The slope is submerged
b. Seepage is parallel to slope
83. A canal is to be excavated at a depth of 6m below the ground level through a soil having following characteristics
G= 2.70 e= 0.9 ∅ = 20° C=15KN/m2
The slope of bank is 1:1. Determine FOS with respect to cohesion when the canal is rapidly emptied completely.
For ∅ = 20° i=45 Sn=0.062
For ∅ = 9.35° i=45 Sn=0.112

Soil Mechanics UESC Prepared By: Sandesh Ghimire