smartworld.asia smartzworld.

com

OBJECTIVES

To impart adequate knowledge to find stresses in various structural parts used in buildings, dams, bridges, retaining
walls and pressure in vessels, etc. To understand the failure phenomenon and to learn how to prevent the failure. To
impart adequate knowledge to continue the design and research activity in structural analysis.

GROUP - A (SHORT ANSWER QUESTIONS)

S. No Question Blooms Program

Taxonomy Outcome
Level
UNIT-I
TORSION OF CIRCULAR SHAFTS & SPRINGS
1 Define a) Torque b) Torsional moment of resistance c) Polar section Understand a
modulus d)Proof load e) Proof stress f) Proof resilience
2 Define Spring constant. Differentiate and explain types of springs. Understand a
3 Derive the equation for power transmitted by a shaft. Evaluate a

4 Define spring and mention types of springs. Understand b

5 State functions of springs. Understand b
6 Write torsional equation and explain the terms Understand & a
Remember
7 Derive the expression for torque transmitted by a hollow shaft Evaluate a
8 Write the Polar Modulus (i) for a solid shaft and (ii) for a hollow shaft. Remember a
9 Why hollow circular shafts are preferred when compared to solid circular Analyze a
shafts?
10 Write the equation for strain energy stored in a shaft due to torsion. Remember a
UNIT-II
COLUMNS AND STRUTS & BEAMS CURVED IN PLAN
1 Define column and effective length of a column. Distinguish between a Understand c
column and a strut.
2 Distinguish between short column and long column. Understand c
3 Define slenderness ratio, crippling load. Understand c
4 Explain the Limitations of Euler‘s Formula? Understand c

1|Page
Specworld.in jntuworld.xyz
smartworld.asia smartzworld.com

S. No Question Blooms Program

Taxonomy Outcome
Level
5 What are the assumptions made in Euler‘s theory to arrive at buckling load on Understand & c
column. Remember
6 Calculate the slenderness ratio of a strut made from a hollow tube of 20mm Evaluate c
outside diameter, 16mm inside diameter and 1.2m long.
7 A steel strut is 0.15m diameter and 12m long. It is built in rigidly at bottom Evaluate c
but completely unrestrained at the top. Calculate the buckling load taking
E=205GPa.
8 Write short notes on curved beams and explain its uses. Understand & d
Remember
9 What are the types of internal forces that act on a curved beam? Remember d
10 Explain the parameters influencing buckling load of a long column Understand & d
Remember
UNIT-III
BEAM COLUMNS & DIRECT AND BENDING STRESSES
1 Define beam columns. Understand e
2 What is the effect of lateral load on the bucking of columns? Understand e
3 What is meant by equivalent length of a column? Understand e
4 Write the expression for maximum deflection, maximum bending Understand e
moment and maximum stress of a beam-column simply supported and
carrying a UDL of intensity w per unit length.
5 Write the expression for maximum deflection, maximum bending Evaluate e
moment and maximum stress of a beam-column simply supported at
ends and carrying a concentrated load at centre.
6 Write short notes on eccentric loading Understand e
7 Define retaining wall, earth pressure and types of earth pressure. Understand f
8 Understand f
State the importance of middle third rule in gravity dams.
& Remember
9 Understand f
Distinguish between active and passive earth pressures.
& Remember
10 Derive an expression for resultant stress of a masonry dam. Evaluate f
UNIT-1V
UNSYMMETRICAL BENDING & SHEAR CENTRE
1 Define centroid, moment of inertia Understand g

2 Write short motes on principal axes. Define product of inertia. Understand g

3 Explain parallel axis theorem for product of inertia. Understand g
4 Define ellipse of inertia and write equation of ellipse and locus of a point. Understand g
5 Write short notes on unsymmetrical bending. Understand g
6 Define Flexure or bending axis. Define combined bending and axial loads and Understand
write its expression g

7 Define shear centre. Write the expressions for shear centre of i) symmetrical Understand g
sections ii) Equal leg angle sections iii) channel sections
8 Explain unsymmetrical bending Evaluate g
9 Explain flexure or bending axis Evaluate g
10 Determine the shear centre of symmetrical section shown below. Evaluate g
UNIT-V
THIN CYLINDERS & THICK CYLINDERS
1 Distinguish between thin cylinder and thick cylinder? Understand h
2 Define hoop and longitudinal stress. Understand h
3 Write the maximum value of shear stress in thin cylinder. Remember & h
Understand
4 What are assumptions made in the analysis of thin cylinders? Remember & h

2|Page
Specworld.in jntuworld.xyz
smartworld.asia smartzworld.com

S. No Question Blooms Program

Taxonomy Outcome
Level
Understand
5 Define shrinkage allowance. Understand h
6 Write short notes on compound cylinders and their boundary conditions. Understand h
7 Write equations for radial stress and hoops stress as per Lame’s theory Remember h
8 Write short notes on lames theory for thick cylinders with assumptions. Understand h
9 What are the different methods of reducing hoop stresses? Remember & h
Understand
10 Derive expression for volumetric strain of cylindrical shells. Evaluate h

GROUP - II (LONG ANSWER QUESTIONS)

S. No Question Blooms Program

Taxonomy Outcome
Level
UNIT-I
TORSION OF CIRCULAR SHAFTS & SPRINGS
1 Differentiate and explain types of springs. Remember & a
Understand
2 a) Explain the theory of pure torsion with assumptions. analyze a
b) Define solid length, spring rate, pitch
3 a)Define spring index (C). (1m) creating a
b) Derive the stiffness of springs with sketches when arranged in series &
parallel.
4 Derive the expression for torque transmitted by a hollow shaft Apply b
5 a) Distinguish between close and open helical coil springs Analyze b
b) What is the value (i) maximum shear forces (ii) central deflection in a leaf
spring subjected to an axial force?
c) Write the equation for the deflection of an open coiled helical spring
subjected to an axial load W.
6 Derive the relation between Twisting moment, Shear stress and angle of twist Apply a
7 Derive expression equations for strength and stiffness of a circular shaft when Creating a
an external torque T is acting on it.
8 Derive expressions for polar modulus for a hollow circular shaft Analyze a
9 Derive expression for strain energy for a solid circular shaft Apply a
10 Derive expression for strain energy for a hollow circular shaft Apply a
UNIT-II
COLUMNS AND STRUTS & BEAMS CURVED IN PLAN
1 Derive the equivalent length of a column whose both ends are hinged using apply c
Euler’s theory.
2 Derive the equivalent length of a column for which one end is fixed and other evaluate c
end hinged using Euler’s theory.
3 Derive the equivalent length of a column for which both ends are fixed using creating c
Euler’s theory.
4 Derive the equivalent length of a column for which one end is fixed and other apply c
end is free using Euler’s theory.
5 Derive Rankine’s formula analyze c
6 Explain the limitations of Euler’s theory apply c
7 Derive the maximum and minimum stresses developed in eccentrically analyze c
loaded long columns
8 Derive the equation for maximum deflection and stresses for a uniformly analyze d

3|Page
Specworld.in jntuworld.xyz
smartworld.asia smartzworld.com

S. No Question Blooms Program

Taxonomy Outcome
Level
loaded lateral strut.
9 Derive the maximum bending moment, maximum shear force for a circular evaluate d
beam loaded uniformly and supported on symmetrically placed columns
10 Derive the maximum bending moment for a semi-circular beam simply apply c
supported on three supports spaced equally.
UNIT-III
BEAM COLUMNS & DIRECT AND BENDING STRESSES
1 Derive the equation for maximum bending moment of a strut subjected to Creating e
compressive axial load and a transverse point load at centre and whose both &analyze
ends are pinned.
2 Derive the equation for maximum deflection of a strut subjected to Evaluate e
compressive axial load and a transverse point load at centre and whose both
ends are pinned.
3 Derive the equation for maximum stress of a strut subjected to compressive Evaluate e
axial load and a transverse point load at centre and whose both ends are
pinned.
4 Derive the equation for maximum bending moment of a strut subjected to e
compressive axial load and a transverse point load at centre and whose both Analyze
ends are fixed.
5 Derive the equation for maximum deflection of a strut subjected to e
compressive axial load and a transverse point load at centre and whose both Evaluate
ends are fixed.
6 Derive the earth pressure of a retaining wall when e
a) Earth pressure at rest Evaluate
b) When a surthrust of intensity, p acts at the horizontal surface of earth
c) When earth is surcharged
7 Derive the resultant stress for masonry dams Evaluate f
8 Write the expressions for direct stress, bending stress, torsional stress and Remember f
principal stresses when a body is under combined effect of axial, bending and &Evaluate
torsional stresses. Also derive equation for equivalent torque.
9 f
Explain middle - third rule for rectangular sections
Understand
10 Derive the maximum and minimum compressive stresses in masonry Understand f
chimneys
UNIT-IV
UNSYMMETRICAL BENDING & SHEAR CENTRE
1 Derive the equation for shear centre of channel section. Understand g

2 Explain the stresses developed due to unsymmetrical bending. Evaluate g

3 Derive the deflections of straight beam subjected to unsymmetrical bending. Evaluate g
4 Explain briefly about shear centre for symmetrical sections. Apply g
5 Derive the resultant shear force, FR for equal leg angle section. Evaluate g
6 Derive the shear centre for channel section Apply g
7 Derive shear centre for unequal I-section Understand g
8 Explain Mohr’s circle of inertia with a neat sketch Evaluate g
9 Explain (a) Principal axes and (b) ellipse of inertia with neat sketches Evaluate g
10 Derive transformation laws for moment and product of inertia. Analyze g
UNIT-V
THIN CYLINDERS & THICK CYLINDERS
1 Derive the stresses developed in thin cylindrical vessel subjected to internal Apply h
pressure.
2 Derive expression for longitudinal stress and maximum shear stress h
developed in thin cylindrical vessel due to internal pressure. Evaluate

4|Page
Specworld.in jntuworld.xyz
smartworld.asia smartzworld.com

S. No Question Blooms Program

Taxonomy Outcome
Level
3 Derive circumferential strain and longitudinal strain for a thin cylindrical Evaluate h
shell subjected to internal pressure
4 Derive volumetric strain for a thin cylindrical shell subjected to internal Evaluate h
pressure
5 Show that when a thin walled spherical vessel of dia 'd' and thickness 't' is Apply h
subjected to internal fluid pressure 'p', the increase in volume equal to

6 Derive the stresses developed in thick cylindrical vessel subjected to internal Analyze h
fluid pressure.
7 Derive the hoop stress developed in thick cylindrical vessel subjected to h
internal fluid pressure alone. Apply
8 What do you mean by thick compound cylinders? How will you determine Apply h
the hoop stresses in a thick compound cylinder?
9 What are the different methods of reducing hoop stress? Explain the terms: Analyze h
wire winding of thin cylinders and shrinking of one cylinder over the another
cylinder.
10 Derive an expression for the radial pressure and hoop stress for thick Apply h
spherical shell.

GROUP - III (ANALYTICAL QUESTIONS)

S. No QUESTIONS Blooms Program

Taxonomy Outcome
Level
UNIT-I
TORSION OF CIRCULAR SHAFTS & SPRINGS
1 Calculate the maximum stress in a propeller shaft with a 400mm external and evaluate a
200mm internal diameter, when subjected to a twisting moment of 4650Nm.
If the modulus of rigidity, C=82GN/m2, how much is the twist in a length 20
times the diameter?
2 A closed coil cylindrical spring of circular cross-section has coils with a evaluate a
75mm mean diameter. When loaded with an axial load of 250N, it is found to
extend 160mm and when subjected to a twisting couple of 3Nm, there is an
angular rotation of 60 degrees. Determine the poisons ratio for the material.
3 Determine the diameter of a solid steel shaft which will transmit 112.5kW at Understand a
200rpm. Also determine the length of the shaft if the twist must not exceed
1.50 over the entire length. The maximum shear stress is limited to 55
N/mm2. Take G = 8x104 N/mm2
4 The internal diameter of a hollow shaft is 2/3rd of its external diameter. Apply b
Compare its resistance to torsion with that of solid shaft of the same weight
and material.
5 A hollow shaft of diameter ratio 3/5 is required to transmit 800kW at Creating b
110rpm. The maximum torque being 20% greater than the mean. The shear
stress is not to exceed 63MPa and the twist in a length of 3m is not to exceed
1.40. Calculate the minimum external diameter satisfying theses conditions.
6 A propeller shaft 280mm in diameter transmits 2.5mW at 250rpm. The Analyze a
propeller weighs 50kN and overhangs its support by 400mm. If the propeller
thrust is of 123kN weights. Calculate the maximum principal stress induced
in the cross-section and indicates its position. C=80MPa
7 A solid shaft of diameter d is subjected to an axial thrust P and an axial Evaluate a

5|Page
Specworld.in jntuworld.xyz
smartworld.asia smartzworld.com

S. No QUESTIONS Blooms Program

Taxonomy Outcome
Level
torque of T. Show that the principal stresses at a point on the surface of the

shaft is given by

8 Find the mean radius of an open – coiled spring (helix angle is 300) to give a Analyze a
vertical displacement and an angular rotation of the loaded end 0.02 radian
under an axial load 40N. The material available is a steel rod of 6mm
diameter. E= 210GPa. C=80GPa
9 A composite spring has two close –coiled helical spring connected in series, Evaluate a
each spring has 12 coils at a mean diameter of 3cms. Find the diameter of the
wire in one of the springs if the diameter of wire in other spring is 3mm and
the stiffness of the composite is 700N/m.
10 In a open coil helical spring having 10 coils, the stresses due to bending and Analyze a
twisting are 98MPa and 105MPa respectively, and the spring is axially
loaded. Assuming the mean diameter of the coils to be 8 times the diameter
of wire, find the maximum permissible load and the diameter of wire for a
maximum extension of 2cm. E=210GPa and G=82GPa.
UNIT-II
COLUMNS AND STRUTS & BEAMS CURVED IN PLAN
1 A tabular steel strut is 8cm external diameter and 5cm internal diameter, 3m Remember c
long and has hinged ends. This is subjected to eccentric lad. Find the
maximum eccentricity for crippling load of 60% of the Euler’s load. The
yield stress being 300MPa and E=200GPa.
2 A hollow circular steel strut with its ends position – fixed, has a length of 3m, Understand c
external diameter of 0.4m and internal diameter 10cm. Before loading, the
strut is bent with a maximum deviation of 0.4cm. Assuming the central line
to be sinusoidal, determine (a) the maximum stress due to a central
compressive end load of 8kN. (B) If the load has an eccentricity of 1.5cm,
then find the maximum stress induced. Take E = 200GPa
3 A steel strut of circular cross-section 1.25m long is hinged at both ends. Find Remember c
the necessary diameter in order that if a thrust of 50kN deviates at the end by
1/10th of the diameter from the axis of the strut, the greatest compressive
stress shall not exceed 35MPa. If the yield stress of steel 300MPa, find the
crippling load. E = 200GPa
A steel column is of rectangular cross-section 4cm X 6cm and is having Understand d
4 initial curvature given by . T carries a compressive load
of 20kN at the hinged ends. (a)Find the maximum resultant stress induced on
either side of the column. (b) If this load is having an eccentricity of 1.5cm,
then also find the stresses. E = 200GPa
5 What is the ratio of strength of a solid steel column of 150mm diameter to apply c
that of a hollow circular steel column of the same cross-sectional area and a
wall thickness of 15mm? The two columns have the same length and have
pinned ends.
6 Determine the safe axial load a timber column of cross-sectional area 150mm Remember c
X 150mm and of 4m length can carry using a factor of safety, 8. Take E =
10kN/mm2 and for (a)hinged ends (b) fixed ends (c)one end free and other
end fixed (d)one end hinged and other end fixed.
7 From the Euler’s crushing load for a hollow cylindrical cast iron column, apply c
150mm external diameter and 20mm thick, if it is 6m long and hinged at both
ends. Compare this load with that obtained by the Rankines formula using
constants 550N/mm2 and 1/1600. For what length of the column would these
two formulae give the same crushing loads? E for the material = 80kN/mm2
8 A steel column consists of two channels ISMC 300 X 35.8 kg/m placed back Remember d

6|Page
Specworld.in jntuworld.xyz
smartworld.asia smartzworld.com

S. No QUESTIONS Blooms Program

Taxonomy Outcome
Level
to back at a clear distance of 15cm and two plates of 350mm X 20mm are
connected to the flanges. Find the crippling load for the column if the
distance between the hinged ends is 8m. Take E = 210kN/mm2.
Properties of channel sections:
Area of cross-section of each channel = 45.64cm2
Ixx = 6362.6 cm4
Iyy = 310.8 cm4
Cyy = 2.36 cm
Thickness of web = 7.6mm
Thickness of flange = 13.6mm
9 A steel strut of circular section is 2m long and hinged at both ends. Find the apply d
necessary diameter such that under a thrust of 100kN at an eccentricity of 0.1
of the diameter from the axis of the strut, the maximum compressive stress
does not exceed 90kN/mm2. If the yield tress in compression for steel is
400N/mm2, find the crippling load of the strut.
10 A cast iron column with a 10cm external diameter and 8cm internal diameter apply d
is 3m long. Calculate the safe load using Rankine’s formula if a) both ends
hinged (b) both ends fixed (c) one end free and other end fixed (d) one end
hinged and other end fixed. σc = 600N/mm2, α = 1/1600. Adopt factor of
safety of 3.
UNIT-III
BEAM COLUMNS & DIRECT AND BENDING STRESSES
A propeller shaft of 20cm external diameter and 15cm internal diameter has Evaluate e
1 to transmit 1103.25kW at 100rpm. It is additionally subjected to a bending
moment of 10kNm and an end thrust of 200kN. Find i) principal stresses and
their planes and ii) maximum shear stress and it plane.
A brick chimney weighs 1600kN and has internal and external diameters at Remember e
2 the base are 2m and 3m respectively. The chimney leans by 5⁰ with the &
vertical. Calculate the maximum stresses in the base. Assume that there is no evaluate
wind pressure and C.G of chimney is 15m above the base.
3 Determine the maximum stress induced in a cylindrical steel strut of length e
1.2m and diameter 30mm. The strut is hinged at both ends and subjected to Evaluate
an axial thrust of 20kN at its ends and a transverse point load of 1.8kN at the
centre. E=208GPa.
Determine the maximum stress induced in a horizontal strut of length 2.5m Remember e
4 and of rectangular cross section 40mm wide and 80mm deep when it carries &
an axial thrust of 100kN and a vertical load of 6kN/m length. The strut is evaluate
having pin joints at its ends. E=208GPa.
5 The line of thrust, in a compression testing specimen 15mm diameter, is f
parallel to the axis of the specimen but is displaced from it. Calculate the Analyse
distance of the line of thrust from the axis when the maximum stress is 20%
greater than the main stress on a normal section.
A short column of additional diameter 40cm and internal diameter 20cm f
carries an eccentric load of 80kN. Find the greatest eccentricity which the Evaluate
6 load can have without producing tension on the cross section.
f
A short column of rectangular cross section 80mm X 60mm carries a load of
40kN at a point 20mm from the longer side and 35mm from the shorter side.
Evaluate
Determine the maximum compressive and tensile stresses in the section.
7
A trapezoidal masonry dam having 4m top width, 8m bottom width and 12m f
high, is retaining water up to a height of 10m. The density of masonry is Remember &
8 2000kg/ m3. The coefficient of friction between dam and soil is 0.55. The Evaluate
allowable compressive stress is 343350N/m2. Check the stability of dams.

7|Page
Specworld.in jntuworld.xyz
smartworld.asia smartzworld.com

S. No QUESTIONS Blooms Program

Taxonomy Outcome
Level
A masonry dam of rectangular section, 20m high and 10m wide, as water up Understand f
to a height of 16m on its one side. Find a) Pressure force due to water and 1m
9 length of dam b) Position of centre of pressure and the point at which the
resultant cuts the base. Take weight density of masonry=19.62kN/ m3 and of
water =9.81kN/ m3. Calculate the maximum and minimum stress intensities
at base of dam.
10 A masonry retaining wall of trapezoidal section is 12m high and retains earth Evaluate f
which is level up to the top. The width at the top is 3m and at the bottom is
6m and exposed face is vertical. Find the maximum and minimum intensities
of normal stress at the base. Take density of earth=1600kg/m3 and density of
masonry=2300kg/ m3 and angle of repose of earth=300
UNIT-IV
UNSYMMETRICAL BENDING & SHEAR CENTRE
A rectangular beam is 15cm wide and 20cm deep. It is used as a simply Understand g
supported beam on a span of 6m. Two loads of 5kN each are applied to the
1 beam, each load being 2m from a support. The plane of loads makes an angle
of 30⁰ with the vertical plane of symmetry. Find the direction of neutral axis
and maximum bending stresses at Point A as shown in figure below.

V
P
20cm U
N A

15cm
2 A simply supported beam T-section, 2.5m long carries a central concentrated Apply g
load inclined at 30⁰ to the Y-axis. If the maximum compressive and tensile
stresses are not to exceed 75MPa respectively find the maximum load the
beam can carry.
A standard I-beam is bent by equal and opposite couples M acting at the ends Apply g
3 of the beam in the plane m-m. Find the maximum stress and the maximum
deflection. I=2400mm4, Iv=150cm4, M=5kNm, l=3m, ϕ=300, E= 200GPa
4 Find the moment of inertia of unequal leg angle iron section as shown in Remember g
figure with respect to axis passing through the centroid.

5 A beam is loaded as shown in figure. Determine the maximum deflection and Creating g

8|Page
Specworld.in jntuworld.xyz
smartworld.asia smartzworld.com

S. No QUESTIONS Blooms Program

Taxonomy Outcome
Level
stress at B.

6 A cantilever beam of I-section is used to support the loads inclined to the V- Remember
axis as shown in figure. Calculate the stresses at the corners A, B, C and D. g
Also locate the neutral axis.

Remember g
A cantilever beam has a channel section as shown in the figure. A
7
concentrated load 15kN lies in the plane of the laods making an angle of 600
with the X-axis. Load,P lies in the plane of the cross section of the free end of
the beam and passes through shear centre,C. Locate points of maximum
tensile and compressive stresses in the beam and determine their magnitudes.

8 A channel section is loaded as shown in the figure. Determine (a) the product Remember g
of inertia with respect to x and y axes; (b) Shear centre.

A steel bar of rectangular section 6cm X 4cm is arranged as a cantilever Remember g

9 projecting horizontally 50cm beyond the support. The broad face of the bar

9|Page
Specworld.in jntuworld.xyz
smartworld.asia smartzworld.com

S. No QUESTIONS Blooms Program

Taxonomy Outcome
Level
makes 300 with the horizontal. A load of 200N is hung from the free end.
Find the neutral axis, the horizontal and vertical deflections of free end, and
the maximum tensile stress.

10 Locate the shear centre of the unsymmetrical section as shown in the figure. apply g

UNIT-V
THIN CYLINDERS & THICK CYLINDERS
1 A steel water pipe 0.6m in diameter has to resist the pressure due to a head of creating h
120m of water. To what thickness should it e made if the working intensity of
pressure in the metal is to be 32N/mm2. After the pipe has lost 2.5mm of its
thickness due to corrosion. Take the specific weight of water to be 10kN/m3
2 Find the circumferential stress at the inner and outer radius respectively in the Remember h
case of a pipe with a 100mm internal diameter and which is 40mm thick
when subjected to an internal pressure of 7.2N/mm2
3 A thick cylinder of steel having an internal diameter of 100mm and an Remember h
external diameter of 200mm is subjected to an internal pressure of 56N/mm2
and an external pressure of 7N/mm2. Find the maximum hoop stress.
4 A thick cylindrical pipe of outside diameter 300mm and thickness of metal Remember h
60mm is subjected to an internal fluid pressure of 40N/mm 2 and an external
pressure of 4N/mm2. Calculate the maximum and minimum intensities of
circumferential and radial stresses in the pipe section.
A compressed air cylinder for laboratory use ordinarily carries approximately apply h
5 15 N/mm2 pressure at the time of delivery. The outside diameter of such a
cylinder is 250mm. If the steel has a yield point of 225N/mm 2 and a safety
factor of 25. Calculate the required wall thickness.
6 A cast iron pipe having an internal diameter of 30cm has wall 6mm thick and Remember h
is closely wound with a single layer of steel wire 3mm diameter under a

10 | P a g e
Specworld.in jntuworld.xyz
smartworld.asia smartzworld.com

S. No QUESTIONS Blooms Program

Taxonomy Outcome
Level
stress of 8MN/m2.Calculate the stresses in pipe and the wire when the
internal pressure in the pipe is 1MPa.
7 A cylindrical steel vessel with hemispherical ends is 60cm long over all, the Apply h
outside diameter is 10cm and the thickness 5mm throughout. Calculate the
change in internal volume of the vessel when it is subjected to an internal
pressure of 15MPa. E=200GPa and υ = 0.28
8 A copper tube of inside diameter 6cm and outside diameter 6.5cm is closely evaluate h
wound with steel wire of diameter 1mm. Find the tension at which the wire
must be wound on the tube if a pressure of 1.5MPa is required before the
copper is subjected to tensile stresses, the tube being free to expand or
contract axially. For copper, Ec=10GPa, υ=0.3, and for steel, Es=200GPa
A cylindrical pressure vessel with closed ends is 25cm external diameter and Understand h
9 5mm thick. It is wound closely with a single layer of circular section steel
wire of 1.2mm diameter under tension of 96MN/m2. If the cylinder is treated
as thin, calculate the (a) initial stress in cylinder, (b) initial pressure which
will produce a stress of 48MN/m2, and (c) stress in the wire under these
conditions. Poisson’s ratio = 0.30
10 A cast iron pipe having an internal diameter of 30cm has wall 6mm thick and apply h
is closely wound with a single layer of steel wire 3mm diameter under a
stress of 8MN/m2. Calculate the stresses in the pipe and the wire when the
internal pressure in the pipe is 1MPa. Es = 200GPa and ECI = 100GPa

11 | P a g e
Specworld.in jntuworld.xyz