Water Proof IR Network Camera

User Manual

Please read this instruction carefully for correct use of the product
Before use this product
 Before operation, we strongly advise users to read this manual and keep it
properly for using later.

 This is product instructions not quality warranty. We may reserve the rights of
amending the typographical errors, inconsistencies with the latest version,
software upgrades and product improvements, interpretation and modification.
These changes will be published in the latest version without special notification.

 When this product is in use, the relevant contents of Microsoft, Apple and Google
will be involved in. The pictures and screenshots in this manual are only used to
explain the usage of our product. The ownerships of trademarks, logos and other
intellectual properties related to Microsoft, Apple and Google belong to the
above-mentioned companies.
 IP CAMERA USER MUANUAL

Table of Contents
1 Introduction ................................................................................................................... 1
1.1 Summarization ............................................................................................................. 1
1.2 Check Package Content ................................................................................................ 1
1.3 Connection ................................................................................................................... 1
2 Installation...................................................................................................................... 2
2.1 Install IP-CAM to Ethernet Network ...................................................................... 2
2.2 Install CMS ............................................................................................................ 2
3 IE Remote Access ........................................................................................................... 4
3.1 LAN........................................................................................................................ 4
3.1.1 Access through IP-Tool ............................................................................ 4
3.1.2 Directly Access through IE ....................................................................... 6
3.2 WAN ....................................................................................................................... 7
4 Remote Preview ............................................................................................................. 8
4.1 The Remote Preview Interface ............................................................................... 8
4.2 Record Playback ..................................................................................................... 8
4.3 Right-click Function ............................................................................................... 9
4.4 Snap Pictures .......................................................................................................... 9
5 Remote Live Surveillance ............................................................................................ 11
5.1 System Configuration ........................................................................................... 11
5.1.1 Basic Information ................................................................................... 11
5.1.2 Date & Time Configuration .................................................................... 12
5.2 Video Configuration ............................................................................................. 12
5.2.1 Camera Configuration ............................................................................ 12
5.2.2 Video Stream .......................................................................................... 13
5.2.3 Time Stamp ............................................................................................ 13
5.2.4 Video Mask ............................................................................................ 14
5.3 Alarm Configuration ............................................................................................ 14
5.3.1 Motion Detection Area ........................................................................... 14
5.3.2 Motion Detection Trigger ....................................................................... 15
5.3.3 Motion Detection Schedule .................................................................... 16
5.4 Network Configuration ......................................................................................... 16
5.4.1 Port ......................................................................................................... 16
5.4.2 Wired ...................................................................................................... 17
5.4.3 NET Traversal Configuration ................................................................. 17
5.4.4 Server Configuration .............................................................................. 18
5.4.5 IP Notify ................................................................................................. 19
5.4.6 DDNS Configuration .............................................................................. 19
5.4.7 RTSP ....................................................................................................... 21
5.4.8 UPNP ...................................................................................................... 22
5.4.9 Mail Setting ............................................................................................ 23
5.4.10 FTP ......................................................................................................... 23
5.5 Advanced Configuration....................................................................................... 24
 IP CAMERA USER MUANUAL

5.5.1 User Configuration ................................................................................. 24

5.5.2 Onvif Configuration ............................................................................... 26
5.5.3 Security Configuration............................................................................ 26
5.5.4 Configure Backup & Restore .................................................................. 27
5.5.5 Reboot Device ........................................................................................ 27
5.5.6 Upgrade .................................................................................................. 27
6 Mobile Surveillance ..................................................................................................... 29
6.1 Network Configuration ......................................................................................... 29
6.2 By Phones with iPhone OS ................................................................................... 29
6.3 By Phones with Android OS ................................................................................. 39
7 IP-Tool .......................................................................................................................... 45
8 Q & A ............................................................................................................................ 48
9 Specification ................................................................................................................. 50
 Page 1 IP CAMERA USER MUANUAL

1 Introduction
1.1 Summarization
This IP-CAMERA (short for IP-CAM) is designed for high performance CCTV
solutions. It adopts state of the art video processing chips. It utilizes most advanced
technologies, such as video encoding and decoding technology, complies with the
TCP/IP protocol, SoC, etc to ensure this system more stable and reliable. This unit
consists of two parts: the IP-CAM device and central management software (short for
CMS). The CMS centralizes all devices together via internet or LAN and establishes a
sound surveillance system to realize unified management and remote operation to all
devices in one network.
This product is widely used in banks, telecommunication systems, electricity power
departments, law systems, factories, storehouses, uptowns, etc. In addition, it is also an
ideal choice for surveillance sites with middle or high risks.

1.2 Check Package Content

Accessories Description
IP-CAMERA The device
Quick Start Guide The Brief instructions of the product
CD CD-ROM with software and manual

1.3 Connection

1. MIC: connect to MIC

2. DC12V: connect to power supply
3. LAN: network port; support PoE power supply
 Page 2 IP CAMERA USER MUANUAL

2 Installation
2.1 Install IP-CAM to Ethernet Network
The connection of digital video server is show below.

Figure 2-1 Connection

User can connect the PC and IP-CAMERA in accordance with above picture. Before
connecting, please connect external devices, and then connect the power.
The connection steps are as shown below:
Step 1: Connect IP-CAM firstly.
Step 2: Internet line connect to Internet transfer equipment or devices
Step 3: Connect power cable to a power outlet.

2.2 Install CMS

After the IP-CAM connected to the Ethernet, user can remote monitoring and managing
the device by using client software or IE browser. This chapter is the client software,
which is the quick install guide of the CMS, the operation and monitor setting details
please refers to CMS user manual in CD.

Note: Before to install control center software in user’s computer, please make sure
all anti-virus software in the computer closed so that CMS can install correctly.

 System requirement
Supported Operating System:

Operating system Comments

Windows XP Windows XP SP2 or most updated patch; Direct 9.0c or above
Windows Vista Windows Vista; Direct 10. c
Window 7 Window 7 Ultimate
Windows 2003 Windows 2003 serve or Directx 9.0c or above
Windows 2000 Windows 2000 SP4 or Directx 9.0c or above

 Computer hardware requirement

Please make sure the software running well and the computer is compatible ：

Recommended PC Specification – 4 channels

Page 3 IP CAMERA USER MUANUAL

Item Specification
CPU Intel Pentium 3.0 GHz or AMD 3000+
Memory 1GB
HDD 160GB

Recommended PC Specification -9 channels:

Item Specification
CPU Intel Core 2 Duo 1.8 GHz or AMD Dual core 3800+
Memory 1GB
HDD 250GB

Recommended PC Specification -16 channels:

Item Specification
CPU Intel Core 2 Duo 2.2 GHz or AMD Dual core 3800+
Memory 2GB
HDD 250GB

Notice:
 The mentioned specifications are provided considering CIF real-time resolution.
 The AMD chip hyper-3800+ and X64 series are not tested.
 For real-time view at CIF, max 25 channels can be played concurrently.
 For real-time view at D1, max 6 channels can be played concurrently.

Installation Process
Find CMS software from CD and then double click “Setup.exe” file to pop up
installation wizard.
Install the software according to the prompts in the wizard. After you complete the
installation, you will see the CMS and IP-Tool icon on the desktop. Please see the user
manual of this software for more details.
If you need to install IP-Tool separately, please double click IP-Tool installation
package and install it according its wizard prompts. After you finish installing, double
click IP-Tool icon to start IP-Tool.
 Page 4 IP CAMERA USER MUANUAL

3 IE Remote Access
User can connect IP-Cam through LAN or WAN. Here only take IE browser (6.0)
for example. The details are as follows:

3.1 LAN
In LAN, there are two ways to access IP-Cam: 1. access through IP-Tool; 2. directly
access through IE browser.

3.1.1 Access through IP-Tool

Step 1: Make sure the PC and IP-Cam are connected to the LAN and the IP-Tool is
installed in the PC from the CD.

Step 2: Use IP-Tool to modify the network of IP-Cam. Then, double click the
icon on the desktop to run this software as shown below:

After starting IP-Tool and clicking the IP-Cam in the list, user can check the information
of IP-Cam. If user cannot confirm which one is himself, please shut off the electricity of
the IP-Cam and then power on it. When shutting off the power, the device information
will disappear. When powering on, the device information will emerge. Well, this device
is the used device. Right click the device information and select “network setup”. Then
the network setup window will pop up.
Page 5 IP CAMERA USER MUANUAL

For example, the network segment of this computer is 192.168.13 x under the local
config table. So, please modify the IP address and Gateway of IP-Cam which must be in
the same network segment with the computer‟s. After modifying, please input the user
name and password and then click “OK” button to save the setting.

Note: The default user name is: admin. The default password is: 123456.

Step 3: Use the IP-Tool to login the IP-Cam.

Right-click the IP address and select “browse with IE”. Then the system will pop up the
IE browser to connect IP-Cam as shown below. IE browser will auto download the
Active X control. If the IE browser cannot download the Active X control, please refer
to Q4 of Chapter 8. Finishing the installation of the Active X control, a login window
will pop up.

Input User name and password and then click “OK” button to login.

Note: User can also use the modified IP address of the IP-Cam. Input the IP address in
the IE browser bar and then click “Enter” to access IP-Cam. The default user name is
admin. The default password is 123456.
Page 6 IP CAMERA USER MUANUAL

3.1.2 Directly Access through IE

The network service is default as shown below:
IP address: 192.168.226.201
Subnet Mask: 255.255.255.0
Gateway: 192.168.226.1
HTTP: 80
Data port: 9008
The first time you used the IP-CAM, you should connect the device with the above
default settings.
Step 1: Manual setup the IP address of the PC, the network segment should be as same
as the default settings of IP-CAM. Right click “My Network Places” icon on the
desktopselect “properties” as shown in the left figure. Right click “Local Area
Connection” at the pops up window, and then select “property” as shown in the right
figure.

Select “Internet Protocol (TCP/IP)” in the “General” tabsclick “properties”manual

input network address information of the PC in the pop up window.

Step 2: Open the IE Browser, input the default address of IP-CAM and confirm. Then
the IE browser will download Active X control automatically. If IE browser can‟t
download Active X control, please refer to Q4 of chapter 8.
Step 3: After downloading Active X control, the login dialog box will pop up as below:
Page 7 IP CAMERA USER MUANUAL

Step 4: input user name and password in the login dialog box and click “OK” button to
enter into the live interface. User can manage and setup the IP-CAM, such as change IP
address etc.

3.2 WAN
a． Access through router or virtual server
Step1: Connecting according to above steps in LAN; enter into System
ConfigurationNetwork configurationBasic configuration to setup the port number
as shown in Fig 3-1:
Step 2: Enter into System ConfigurationNetwork configurationIP configuration to
change IP address as shown in Fig 3-2:
Notice: The steps above should be saved after the change of the port and IP address.
Log back in the device with the saved setting.

Fig 3-1 Port Setup Fig 3-2 IP Setup

Step 3: Enter into the router‟s management interface through IE browser; remap the IP
address and port of IP-CAM in the “virtual server”. The name depends on the router.
Please refer to Fig 3-3:

Fig 3-3 Router Setup

Step 4: Open the IE browser and input its WAN IP and http port to access. The
following steps are as same as “Step 2, 3 and 4” of Chapter 3.1.2 in LAN.
Page 8 IP CAMERA USER MUANUAL

4 Remote Preview
4.1 The Remote Preview Interface

Fig 4-1 Remote Preview

1 People icon 2 Fix size 3 Zoom in

4 Zoom in 5 Zoom out 6 Full screen
7 Start record 8 Playback 9 Snap
10 Enable audio

 When motion detection alarm is triggered, the people icon turn red.
 Click icon, user can zoom in the preview image to suitable size, drag the
cursor on the enlarged image to view suitable preview area; click icon, user can
zoom out the enlarged image; click icon, user can full-screen the live image.
 Clicking icon will appear a save path window and the record file can save on
user‟s PC.

Note: On Window 7 and Window Vista, user can not record or snap pictures until UAC
function is disabled. Please refer to following steps: Start—Control panel—User
accounts—Change user account control settings in which user needs to drag the scale to
Always notify end and then click “OK” button to save.

4.2 Record Playback

Click icon and refer to Fig 4-2:
Page 9 IP CAMERA USER MUANUAL

Fig 4-2 record playback interface

After selecting the record date, the record files will be displayed in the record file list
box. User can double click a
certain record file to playback or check a certain file. Then click Play button to do
playback. User can do relating operation according to some buttons in the playback
interface.

4.3 Right-click Function

Clicking right mouse will appear a pull-down list as below:
Stream: 720P, VGA, QVGA.
Turn off the live: Click this item will close present live preview.
Enable audio: Enable remote audio transmission. Users can hear
the audio from the IP-CAM.
Full screen: The live preview picture will full-screen display.
Double click or click right mouse to return to the previous
interface. Fig 4-3 Right key sub-menu
Online user: Display user‟s list connect to the device.
System information: Display the device information: device name, firmware version,
software build date, kernel version and hardware version.

4.4 Snap Pictures

1. Select the picture number, and then click “Snap” icon as shown in the Fig
4-4:
2. User can snap multiple pictures. Select the picture number from Frame pull down
list box, such as 3, and check “Title” and “Time” to show capture title and time on the
snap pictures simultaneously. Refer to Fig 4-5:
3. Click “Browse” to set saving path; Click “Save” to save pictures to HDD on the
Page 10 IP CAMERA USER MUANUAL

computer; Click “Printer setup” to set the printer and print the snap pictures; drag the
scroll bar to view all snapped pictures.

Fig 4-4 Single Snap

Fig 4-5 Multi-picture Snap

Page 11 IP CAMERA USER MUANUAL

5 Remote Live Surveillance

User can remote setup the parameters of the device. Functions of remote configurations
include: System Configuration, Video Configuration, Alarm Configuration, Network
Configuration and Advanced Configuration. User should firstly select the menu on the
left, and then setup the relative parameters. When a user setup parameters of a certain
device, other users can not setup this device.

5.1 System Configuration

The “System configuration” includes two submenus: Basic Information and Date &
Time.

5.1.1 Basic Information

In the “Basic Information interface, user can setup the device name and also can check
the relative information of the server
Setting steps:
1. Clicking the "Config" icon will appear the menu list.
2. Clicking the “Basic Information "will pop up a window as shown in Fig 5-1:
3. Input the name of the device in the "Device name" text box.
4. Press the "Save" button to save the settings.

Fig 5-1 Basic Information Config

Please refer to the following table for parameters and instructions of server basic
configuration.

Parameter Meaning
Software version The software of the device
Software build date The software build date of the device
Kernel version The kernel version of the device
Hardware version The hardware version of the device
Mac Address MAC address of device
Maximum number of user Support max 4 users to access
Device name Name of the device.
Page 12 IP CAMERA USER MUANUAL

5.1.2 Date & Time Configuration

Setting steps:
1. Enter into "System Configuration" “Date & Time”. Refer to Fig 5-2:
2. Select “Modify Time ", user can self-define time. Choose the right "Time Zone"
according to user‟s location.
3. User can also enable DST and set DST mode and time.
4. Setup time by selecting the “Synchronize with NTP Server”.
5. Press the "Save" button to save the settings.

Fig 5-2 Date &Time Config

5.2 Video Configuration

Camera Configuration includes four submenus: Camera Configuration, Video Stream,
Time Stamp and Video Mask.

5.2.1 Camera Configuration

Setting steps:
1. Enter into "Video Configuration " "Camera" interface as shown in Fig 5-3:

Fig 5-3 Basic Configuration

Page 13 IP CAMERA USER MUANUAL

2. User can adjust Brightness, Contrast, Hue and saturation of the picture.
3. Select white balance mode.
4. Sharpen, denoise , white balance, frequency, CVBS format and Day-Night mode are
adjustable.
5. User also can enable the image mirror and image overturn function.
6. Press the "Save" button to save the settings.

5.2.2 Video Stream

1.Enter into "Video configuration" "Video Stream" to see a interface shown as Fig
5-4:

Fig 5-4 Video Stream

2. Select the resolution of the single frame image at the "Resolution" pull down list.
3. Select the quantity of video per second at the "Frame rate" pull down list.
4. Select the data stream type at the "Bit rate type" pull down list.
5. Set the video quality at the "Video quality" pull down list.
6. Choose the alarm picture size.
7. Press the "Save" button to save the settings.

5.2.3 Time Stamp

Enter into "Video configuration""Time Stamp" to display the interface as shown
in Fig 5-5:

Fig 5-5 Time Stamp

1. Select Date Format to show in the live image.

Time stamp: time displayed in the live preview pictures. Four items can choose from:
top left, top right, bottom left and bottom right.
2. Press the "Save" button to save the settings.
Page 14 IP CAMERA USER MUANUAL

5.2.4 Video Mask

You can set 4 mask area at most.

Fig 5-6 Video Mask

Enable the mask, select color and transparent of the mask area and then drag the mouse
to set the mask area. This will take you see a gridding area. After that, click “Save”
button to save the settings. Then you will see a mask area on the live image.

5.3 Alarm Configuration

Alarm configuration includes three submenus: Motion Detection Area, Motion
Detection Trigger and Motion Detection Schedule.

5.3.1 Motion Detection Area

1. Enter into “Alarm configuration""Motion Detection Area" to see a interface shown
as Fig 5-7:
2. Move the "Sensitivity" scroll bar to setup the motion trace sensitivity.
3. Check the "Add”, press the "Ctrl" button and move mouse to select the motion
detection area; Select “Erase” and move the mouse to clear all motion detection area.
4. Press the "Save" button to save the settings.
Page 15 IP CAMERA USER MUANUAL

Fig 5-7 Motion Detection Area

5.3.2 Motion Detection Trigger

1. Enter into “Alarm Configuration" "Motion Detection Trigger" to display a
interface as shown in Fig 5-8:
2. Check "Enable alarm" check box. Then all functions under this interface will be
activated.
4. Trigger Email: Check “Attach picture” and select email addresses in the “Receival
email address” text box(Email address shall be set first in the Mail config
interface).Then the triggered snap pictures will be sent into those address. User also can
define the subject and content of the email.
5. Trigger FTP: Check “Uploading picture”. Then the triggered snap pictures will be
sent into FTP server address.
Note: Please refer to FTP configuration chapter for more details.

6. Press the "Save" button to save the settings.

Fig 5-8 Motion Alarm Trigger

Page 16 IP CAMERA USER MUANUAL

5.3.3 Motion Detection Schedule

Enter into “Alarm configuration" "Motion Detection schedule" interface as shown in
Fig 5-9:

Week schedule
User could set the alarm time from Monday to Sunday for alarm everyday in one week.
Note: The lengthwise means one day of a week; the rank means 24 hours of a day.
Mouse clicks on the pane to set the alarm hours. Green means selected area. Blank
means unselected area.
2."Add": add the schedule for a special day.
3."Erase": delete holiday schedule

Day schedule
User could set alarm time for alarm in some time of special day, such as holiday.
1. Select a date at the "Date" pull down list, press "Add" button to add that date to the
list box on the right side and then move the scroll bar to set the schedule of that day.
2. Select a date in the list box on the right side, and press "Erase" to remove the
schedule on that day.
Press the "Save" button to save the settings.
Note: Holiday schedule is prior to Week schedule.

Fig 5-9 Motion Detection Schedule

5.4 Network Configuration

Network configuration includes ten submenus: Port, Wired, NET traversal Config,
Server Configuration, IP Notify, DDNS Config, RTSP, UPNP, Mail Setting and FTP.

5.4.1 Port
1. Enter into "Network config""Port" to see the interface as shown in Fig 5-10:
Page 17 IP CAMERA USER MUANUAL

Fig 5-10 Port Config

2. Input port number for IE access in the "HTTP Port" textbox.

1. Input the port number for audio & video transmission in the "Data Port" textbox.

5.4.2 Wired
1. Enter into "Network Configuration""Wired" to see a tab shown as Figure 5-11:

Fig 5-11 Wired Config

2. There are two Options for setup IP: obtain an IP address auto by DHCP protocol and
use the following IP address, user can choose one of options for requirements.
3. Use the following IP address: display the IP address, subnet mask, gateway and DNS
of the device.
4. PPPOE: User needs to manual input the user name and password for dial-up internet.
Firstly, user needs to login IE clients, then enter into user name and password of PPPoE,
save the setting and exit. Secondly, setup IP address change notice. Thirdly, connect
with Modem, then the device will dial-up internet automatically.
6. Press the "Save" button to save the settings.

5.4.3 NET Traversal Configuration

In this interface, user can access to network without dynamic domain name and port
forwarding by enabling NET transit.
Page 18 IP CAMERA USER MUANUAL

1.Enter into “Network Configuration” “NET traversal Config”. Refer to Fig 5-12:

Fig 5-12 Transit

2. Check “transit enable”. Then save the setting.

3. Input www.upnpicp.com in IE address; download and install Active X. Then a window
shows up as Fig 5-13:

Fig 5-13 Login

4. Input the only device ID of the IP-CAM or user-defined name. And then input user
name and password.

Note: The default user name and password are “admin” and “123456”
respectively.

5.4.4 Server Configuration

Enter into “Network Configuration” “Server Config”. Please refer to Fig 5-14:

Fig 5-14 Server Configuration

Page 19 IP CAMERA USER MUANUAL

1. Check “Do you want IP Camera to connect Server.

2. Check the IP address and port of the transfer media server in the ECMS/NVMS. Then
enable the auto report in the ECMS/NVMS when adding a new device. Then input the
remaining information of the device in the ECMS/NVMS. After that, the system will
auto allot a device ID. Please check it in the ECMS/NVMS.
3. Input the above-mentioned server IP, server port and device ID in the responding
boxes. Click “save” button to save the settings.

5.4.5 IP Notify
1. Enter into “Network Configuration””IP Notify” to see a tab as shown in Fig 5-15.
2. If the “Enable notifying change of IP” is selected, when the IP address of the device
is changed, a new IP address will be sent to the appointed mailbox automatically; If
“FTP” is selected, when the IP address of the device was changed, a new IP address will
be sent to FTP server.

Fig 5-15 IP Notify Config

5.4.6 DDNS Configuration

1. Enter into "Network Configuration""DDNS Configuration" tab as shown in Fig
5-16:

Fig 5-16 DDNS Config

Note: The steps to band a domain name for video surveillance server are as follows.
Firstly, register a user name and a password to log on the website of service supplier,
and then apply for a domain name online for the server. After that, users can visit the
server through inputting the domain name at IE terminal.

2. Press the "Save" button to save the settings.

Please refer to the following table for parameters and instructions of DDNS
configuration.
Page 20 IP CAMERA USER MUANUAL

Parameter Meaning
Address of the website which provided by domain name supplier. The
DDNS server optional: www.dns2p.net ， www.88ip.net ，www.meibu.com ，
www.dyndns.com，www.no-ip.com，www.3322.org and mintdns type.
User name Log in the website of domain name supplier
Password Log in the website of domain name supplier

1. Apply the Domain Name (Take dns2p for example)

(1) Register in the Web

Register dialog box

Step 1: Fill in the blank of IE address with „www.dns2p.com‟.

Step 2: Click to enter the website.
Step 3: Click "New User" in the right of homepage to register. For example: User ID is
„abc‟, and password is „123456‟. The register dialog display as below:

(2) Login
Step 1: Return to homepage after registering successfully.
Step 2: Click "Account Manager" on the right of homepage to login.
Step 3: Input the username and password with the information that you have registered.
Step 4: Click "Enter" key after filling in the textbox.

Log in
(3) Domain Setup
Page 21 IP CAMERA USER MUANUAL

Step 1: Click "Domain Management" on the left to set the domain.

Domain setup

Step 2: Input the domain in the textbox. For example, you set „IP-CAMERA‟ as the
domain.
Step 3: Click "Submit" button, the system will pop up a dialog box to show that the
domain is added successfully.

Note: Time of probationary period is one month. If user wants to use it continuatively
after one month, please Step 4: click "Buy Now" in the right of homepage to pay for it.

2. Setup in the IP-CAMERA

⑴ DOMAIN
Domain is set in „1. Apply the Domain Name‟. According to the example above, the
domain is „WWW. IP-CAMERA.dns2p.com‟.

⑵ USER ID
Username of registered which is set in „(1) Register in the Web‟. According to the
example above, user ID is „abc‟.

⑶ PASSWORD
Password is set in „(1) Register in the Web‟. According to the example above, password
is „123456‟.
Note: If the connection fails, press the "INFO" button. Now the system will display:
„DDNS NONE‟. Then you need to check network and information above and try again.

3. Application
Connect IP-CAMERA to the Network Client.
Step 1: After popping up the login interface, fill in "Server" textbox with „*.dns2p.com‟
to visit the Network Client of the IP-CAMERA. The domain set in „(3) Domain Setup‟.
According to the example above, fill in "Server" textbox with
„IP-CAMERA.dns2p.com‟.
Step 2: Click "save" button to save the above setting.

5.4.7 RTSP
Enter into “Network Configuration” “RTSP” interface as shown in Fig 5-17:
Page 22 IP CAMERA USER MUANUAL

Fig 5-17 RTSP

1. Select “Enable RTSP server.

2. RTSP Port: Access Port of the streaming media. The default number is 554.
3.RTSP Address: The RTSP address you need to input in the media player.
4. You can also choose to enable anonymous viewer login

5.4.8 UPNP
Enter into “Network Configuration” “UPNP” interface as shown in Fig 5-18.
Select “Enable UPNP” and then input friendly name.

Fig 5-18 UPNP

Enable UPNP
Double-click the “My Network Places” icon on the desktop in PC and select “Show
icons for networked UPnP devices” in the “Network Tasks” list box. Then a
information window will pop up. Click “YES” button to see a “Windows Components
Wizard” dialog box pop up as shown below. Then press “Next” to continue. After
finished the installation of configuring components, the UPnP icons will display. Users
can double-click certain icon to connect the remote surveillance login interface through
IE.

If “Show icons for networked UPnP devices” can‟t display in the “Network Tasks” list
box, please follow the below operation:
Page 23 IP CAMERA USER MUANUAL

 Click “Tools”-- “Folder options”

 Check the “Show common tasks in folders” in the “Tasks” check box, UPnP icon
will display.

5.4.9 Mail Setting

Enter into “Network Configuration”  “Mail Setting” interface. Please refer to Fig
5-19.

Fig 5-19 Mail Setting

1. From Email: sender‟s e-mail address

2. User name and password: sender‟s user name and password
3. Server address: SMTP name of sender
4.Select the secure connection type at the Secure Connection pull down list according to
user‟ actual needs
5. Receival email address list: add email address into the list
6. Receival email address: receiver‟s e-mail address
7. After all parameters setup, user can click “Test your account settings”. If email sent
successful, a “Test Successful” window will pop up, if not, users can try other email
addresses or check the setting.

Notice: If user change the static IP into PPPoE and select mailbox, there will be an
e-mail sent to users‟ mail box for notify a new IP address.

5.4.10 FTP
Enter into Network ConfigurationFTP interface; please refer to Fig 5-20:
Page 24 IP CAMERA USER MUANUAL

Fig 5-20 FTP Setting

1. Add: Click Add button to input FTP server‟s server name, address, port number, user
name, password, and upload path, click OK to confirm the setting. Refer to Fig 5-21:
2. Modify：User can click this button to change some information of the FTP server
3. Delete：Select certain FTP account; Click this button to delete this account
4. Test ：Select certain FTP account; Click this button to test its valid or not.
Please refer to the following table for parameters and instructions of FTP configuration.

Parameter Meaning
Server name The name of the FTP server
Server address The address of the FTP server
Port The port number of the FTP server
User name The user name of the FTP server
Password The password of the FTP server
Path The save path for FTP files

Fig 5-21 Add

5.5 Advanced Configuration

Advanced configuration includes five submenus: User Configuration, Onvif
Configuration, Security Configuration, Configure Backup & Restore, Reboot and
Upgrade.

5.5.1 User Configuration

Enter into "User Configuration" interface. Refer to Fig 5-22:
Add user:
1. Clicking "Add" button pops up "Add user" dialog box. Please refer to Fig 5-23:

Fig 5-22 User Configuration Fig 5-23 Add User

Page 25 IP CAMERA USER MUANUAL

Note: After bind physical address to the IP-CAM, user can access the device on this PC
in network only. If the MAC address was ““00:00:00:00:00:00” which means it can be
connected to any computers.

2. Input user name in "User Name" textbox (only letters).

3. Input characters in "Password" and "Confirm Password" textbox (letters or numbers).
4. Input the MAC address of the PC in "Binding MAC address" textbox.
5. Click “OK” button and then the new added user will display in the user list.

Modify user:
1. Select the user which needs to modify password and physical address in the user
configuration list box.
2. Clicking “Modify” button will pop up “Modify user” dialog box as shown below.

Fig 5-24 Modify User

3. Input original password of this user in the “password” text box.

4. Input new password in the “New password” and “Confirmation” text box.
5. Input computer‟s physical address which is used to access the server in the “User PC
MAC” text box.
6. Click “OK” button to modify password and binding MAC address successfully.

Delete user:
1. Select the user which needs to delete in the user configuration list box.
2. Clicking “Delete” button will pop up a confirm dialog box. Then click “OK” to delete
the user.

Note: The default super administrator cannot be deleted.

Parameter Meaning
User Name User name to operate the logon client end
User Type Type of users, normal user, advanced user and super administrator
The MAC addresses of user access the server which should setup
Binding MAC address
according to actual MAC address of server.
Password Password to log in the client terminal
Confirm Password Password to log in the client terminal
Page 26 IP CAMERA USER MUANUAL

5.5.2 Onvif Configuration

This function is mainly used for connecting our device through other companies‟
monitoring platform software, such as, Hikvision, Axxon, Milestone., etc.

Fig 5-25 Onvif Config

5.5.3 Security Configuration

Enter into Advanced ConfigurationSecurity Configuration to see a tab shown in Fig
5-26:
Check “Enable IP address” check box, select “Deny the following IP address”, input IP
address in the IP address list box and click “Add” button. Then this IP address will
display in the list box; the operation step of “Allow the following IP address” is the
same with “Deny the following IP address”
Select the IP address which needs to be deleted from the IP address list box and click
“delete” button to delete that IP address.
Check “Enable MAC address” check box, select “Deny the following IP address”, input
MAC address in the MAC address list box and click “Add” button. Then this MAC
address will display in the list box; the operation step of “Allow the following MAC
address” is the same with “Deny the following IP address”.
4. Select the MAC address which needs to be deleted from the MAC address list box
and click “delete” button to delete that MAC address.
5. Click "save" button to save the above setting.

Fig 5-26 Security Configuration

Page 27 IP CAMERA USER MUANUAL

5.5.4 Configure Backup & Restore

Enter into Advanced configurationConfigure Backup & Restore Interface. to Fig
5-27.
 Import & Export Configuration:
User can import or export the setting information from PC or to device.
1. Click “Browse” to select save path for import or export information on PC.
2. User can import or export all setting information to PC, but those two settings “user
configuration” and “network configuration” are exceptional.

Fig 5-27 Backup and Restore Configuration

 Default Configuration
Click “Load default” button to restore all system settings to default status.

5.5.5 Reboot Device

Enter into Advanced configuration—Reboot device to see a interface as shown in Fig
5-28:
Click “Reboot device” button to reboot the device.

Fig 5-28 Reboot device interface

5.5.6 Upgrade
Enter into Advanced Configuration—Upgrade interface shown as Fig 5-29:
1. Click “Browse” button to select the save path of the upgrade file
2. Click “Upgrade server firmware” button to start upgrading the application program
3. The device will restart automatically
4. After you successfully update the software, click “OK” button to close IE and then
re-open IE to connect IP-Cam.
Page 28 IP CAMERA USER MUANUAL

Fig 5-29 Upgrade

Notice: User can‟t disconnect to PC or close the IP-CAM during upgrade.

Page 29 IP CAMERA USER MUANUAL

6 Mobile Surveillance
This IP-CAM supports mobile surveillance by phones with Windows mobile, iPhone,
Android and Blackberry OS. Please check the operation system version of mobile
before use; and connect the IP-CAM to Internet.

6.1 Network Configuration

 Access device via LAN
Step 1: Connect device via wireless router. Then checkmark DHCP both in router and
device to automatically acquire IP address or enter the IP address manually.
Step 2: Use WIFI function in your mobile phone to connect the wireless router.
Note: Make sure your phone network and device network are in the same network
segment on LAN.
Step 3: Add the IP address and port in the mobile phone surveillance client.

 Access device via 3G network

Step 1: Set the device network. Please enter Main MenuSetupNetwork tab.

If you use PPPoE to connect device, please enable PPPoE and input username and
password received from you ISP in network tab. Then click “Apply”. You can enter
Main MenuInformationNetwork tab to see the IP address. If you want to utilize
dynamic domain name, please apply for a domain name in a DNS server supported by
the device.
If you have a static WAN IP address, please enter Main MenuSetupNetwork
tab to input your IP address, gateway and port.
If you use LAN IP address, please enter Main MenuSetupNetwork tab to
input your IP address, gateway and port and then forward IP address and port number in
virtual server setup of the router or virtual server(If you has enabled the UPnP function
in both the device and router, you can skip this step). Port forwarding setting may be
different in different routers and servers. Please refer to the router‟s manual for details.
After you forward your LAN IP address and port, please check the WAN IP address in
the router or server.

Step 2: Add the WAN IP address or domain name in mobile phone surveillance client.

6.2 By Phones with iPhone OS

1. Install through iPhone.

Step 1: Open App Store software as shown in the figure on the left.
Step2: Search “SuperLive Pro” and click “Free” button as shown in the figure on the
right.
Page 30 IP CAMERA USER MUANUAL

Step 3: Click “Install App” button as shown in the figure on the left.
Step 4: Input iTunes Store password and then click “OK”. The software will be installed
automatically.

 Install Software through PC

Step 1: Install iTunes store in PC and then login.

Step 2: Connect iPhone and PC.

Page 31 IP CAMERA USER MUANUAL

Step 3: Search “SuperLivePro” and select it.

Step 4: Click “Download” button.

Step 5: Input username and password.

Page 32 IP CAMERA USER MUANUAL

Step 6: Synchronously apply SuperLivePro software to iPhone/iPad.

 SuperLivePro Instruction
1. Login
Page 33 IP CAMERA USER MUANUAL

Step 1: Choose network type. There are two network connection ways:
3G/3G +WIFI, well video quality. This network supports main stream and sub stream.
The real-time image will be displayed by using sub stream.
3G-, poor video quality contrast to the above mentioned network.
Step 2: Input server, account and password.

Server: WAN IP address (or domain name) plus HTTP port of the device. For example:
210.21.183:89 or 123.dvrdydns.com:89.
Note: The default http port of the device is 80. If this port is modified, please use
the modified port.
Account and Password: The login account and password of the device. The default
account is admin and the default password is 123456.

Step 3: Click【Login】button to access the device.

2. Main Interface

There are many buttons in the main interface, such as, screen mode, favorite channel,
snap, record, open/close audio, talk, PTZ., etc.

：Image view button. The pictures snapped in the live will be checked by clicking
this button.

：Playback button. Click this button to enter into playback interface.

：Settings button. Click this button to set local configuration (Some can also
support remote configuration).

：Information button. Click this button to check lots of information including local
information, device information, network information, etc.

：Server list button. Click this button to add server list.

Page 34 IP CAMERA USER MUANUAL

：Help button. Help you know about the use of this software quickly.

：CMS button. Make you preview the live image of multi-devices.

：Log off button. Click this button to return to the login interface.

：Screen mode button. You can choose 1，4，6，8，

9，13 or 16 screen display mode.

：Favorite channel display button. If you save your favorite channel in the favorite
server list, clicking this button will directly play all favorite channels you have saved.

：Snap button. Choose the channel and click this button to capture the channel
image.

：Local record button. Choose the channel and click this button to start recording.

： Open/Close audio. Choose the channel and click this button to open/close the
audio of this channel.

：Open/Close talk. Click this button to pop up the servers which support talk
function. Select the device to start talking.

：Set video parameter button. Select the channel and click this button to set the
video parameters including brightness, hue, saturation and contrast.

：PTZ button. Click this button to pop up PTZ control panel.

：Choose bitrate priority or quality priority according to
your network condition.

Channel indicator instruction:

：Video loss ： Schedule recording ：Others

：Sensor alarm ：Motion alarm

：Motion /sensor alarm based recording or manual recording

3. Server list
Click button to pop up the following picture.

 Add device: Click “Add” button in the top right corner to pop up a dialog box
as shown in the following left picture. Input the relative information of the device and
click “Save” button.
Page 35 IP CAMERA USER MUANUAL

 Delete device: Click button behind the device name to delete this device.
 Edit device: Click button behind the device name to edit the information of
this device.
 Backup & restore: It is recommended to click “Backup” button to reserve the
information of all devices. Then you can click “Restore” button to restore all device
information after you re-install the client or delete the device uncarefully.
 indicates the device has been connected; indicates the device is
connecting; indicates the device is not connected.

4. Live Preview
Once you access the device, the system will automatically display the screen mode in
accordance with the channel number of the device

Note: The maximum number of channels which can be connected are nine after
login.

1. Click “Screen mode” button to select channel as shown in Fig 1.

2. When there is video playing in a screen, you can switch the channel by long
pressing the screen as shown in Fig 2.
3. When no video is playing in a screen, click this screen to choose channel as shown
in Fig 3.
4. When the single channel is playing, you can zoom in/out the image by swiping
you finger up and down as shown in Fig 4.
5. When the single channel is playing, the channel can be switched by swiping your
finger left or right as shown in Fig 5.
6. When multi channels are playing, drag one channel screen to the other channel
screen. This will make these two channels change the position of each other.
Page 36 IP CAMERA USER MUANUAL

Fig 1

Fig 2 Fig 3

Fig 4 Fig 5

5. CMS Function
This function makes multi-device managements and preview come true.

Step 1: Click to enable CMS function. When this icon turns green, it means this
function is enabled.
Step 2: Click to choose channel as shown in the right picture. After you choose
the channel, click “ok”, the system will display the related image automatically.
Page 37 IP CAMERA USER MUANUAL

 If channels have been added into the group, you can see the images by clicking the
group name.
 On viewing the group channel images, click button and select channels to
check other channel images.
 Click “Exit CMS” to exit CMS mode and return to the main interface of the
device.

6. Favorite Channel/Group
There are two kinds of favorite channels: favorite channels of the device and favorite
group of CMS.

 Favorite channels of the device

Step 1: Click to enter into device management list. Click the device name to
extend channel. Enlighten the channels to save favorite channels as shown in the
following picture on the left.
Step 2: Return to the main interface and click button to play the favorite
channels.

 Favorite groups of CMS

Enable CMS function and enlighten the group to save the favorite groups as shown in
the following picture on the right.
Then click button to play. Only one favorite group can be collected.

：Color means the channel or group has been collected. Grey means the channel
or group isn‟t collected.

7. Playback Interface
Click “Playback” button to enter the playback interface. Then click “Search” button to
Page 38 IP CAMERA USER MUANUAL

search the file. To play the record by clicking this file name.

8. Image View

Click button to view the captured pictures.

9. Settings Interface
In this interface, you can configure the local settings.
Page 39 IP CAMERA USER MUANUAL

10. Information Interface

In this interface, you can view system information.

6.3 By Phones with Android OS

Software Installation

Step 1: Run “Play Store” (or Google market) program.

Step 2: Search “SuperLivePro”.
Page 40 IP CAMERA USER MUANUAL

Step 3: Press “Install” button.

Step 4: Install the software subject to the notes. Once the downloading is done, the
software will install automatically.

Login
Step 1: Configure the network of your device and mobile phone.

Step 2: Input the WAN IP address/domain name and port of your device in the sever
Page 41 IP CAMERA USER MUANUAL

column. The port should be HTTP port of your device. The default http port of the
device is 80. If you have changed your http port, please enter the new port here. For
example: 210.21.228.183:89 or 123.dvrdydns.com:89.
Step 3: Input the account and password of your device. The default account name is
admin and the default password is 123456.
Step 4: Check “Remember Server” to save the setting. When you login next time, you
can click button to select this server for quick access.

Main Menu

Live View

PTZ
Snap
Record
Talk

Enable/disable audio

Hide
Playing favorite
channel

Image View
Page 42 IP CAMERA USER MUANUAL

The first picture

The previous picture
Next picture
The last picture
Zoom in
Zoom out
Delete

Record Playback
Click “Playback” in the main menu interface to enter playback interface. Then choose
the channel you want to playback. This will take you to see the record file. Click this
file to play.

Pause/P
lay

Stop

Forward

Backward
Page 43 IP CAMERA USER MUANUAL

Server List

In the main menu interface, click “Server list” to see the above picture on the left hand.
Add Server: Click button to pop up a window as shown in the above picture on the
right hand. Enter the name, server, user and password of the device you want to add.
Then click “Save” button to save the server. When you log in next time, you can choose
and quickly access this server by clicking the little triangle button in the server column.
Modify Server: Click button to modify the server information.
Delete Server: Click button to delete the server information.

Settings
In the main menu interface, click “Settings” to enter the settings interface where you
can configure local settings.
Click “Local” to enter local settings interface. In this interface, you can set favorite
channel and storage .

Favorite Channel: Check the favorite channels and click “Save” button to save these
channels. Then go into live interface and click button to play these favorite
channels.
Page 44 IP CAMERA USER MUANUAL

Storage: Setup the relevant parameters of mobile video.

Information View
Page 45 IP CAMERA USER MUANUAL

7 IP-Tool
Updating through IP-Tool
Note: Do not cut off power supply and internet when updating. If the device is
unable to start because of the failure of upgrade, it needs to retrofit.

Acquire the IP-Tool from the supplier and then double click the IP-Tool icon to
run this software. Then the device can be searched; if the device can‟t be searched,
please check whether the PC and the device connect to the network or not.

Click the device to check its detail information as shown below:

When upgrading the software and kernel, the IP address of PC and device should be at
the same network segment. If the network segment is different, user should change the
IP address by right clicking the device and then select “network setup”. Modify IP
address dialog box will appear as follows:
Page 46 IP CAMERA USER MUANUAL

Modify IP address and click OK button to exit the dialog box. After that, IP-Tool will
display the new IP address.

 Upgrade Software
Select the device; right click “Update software”. Click “Update” to start upgrading，the
progress bar will display as below. When upgrading, please do not disconnect PC and
the device and make sure the power is on.

After finishing upgrading, a massage box will pop up as below:

Click OK button to exit the update dialog box, and then the device will restart
automatically. Select the device and right click it to select “Update kernel”. This will
bring up a dialog box as below:
Page 47 IP CAMERA USER MUANUAL

Input the relevant information and click “Browse” button to choose your update file.
After that, click “Update Kernel” button to start updating. When upgrading, do not
disconnect PC to device and make sure the power is on. The update progress bar will
display as below:

After finishing upgrading, a message box will pop up. After a while, the device will
restart automatically.
Page 48 IP CAMERA USER MUANUAL

8 Q&A
Q: How to find my password if I forget it?
A：Joint the default line and GND line to reset.
Default IP: 192.168.226.201
User name: admin
Password: 123456

Q：Fail to connect devices through IE browser, why?

A: Network doesn‟t connect well. Please check the connection and make sure it
connected well.
B: IP is not available. Reset the valid IP.
C: Web port number has been revised: contact administrator to get the correct port
number.
D: Exclude the above reasons. Recover default setting by jointing the default line and
GND line.
Note: default IP: 192.168.226.201，mask number: 255.255.255.0

Q：IP tool cannot search devices, why?

A：It may be caused by the anti-virus software in your computer. Please exit it and try to
search device again.

Q：IE cannot download ActiveX control. How can I do?

a. IE browser blocks ActiveX. Please do setup following below.
① Open IE browser. Click Tools-----Internet Options….

② select Security------Custom Level….Refer to Fig 4-1

③ Enable all the sub options under “ActiveX controls and plug-ins”. Refer to Fig 4-2
Page 49 IP CAMERA USER MUANUAL

Fig 4-1 Fig 4-2

④ then click ok to finish setup.

b. Other plug-ins or anti-virus blocks ActiveX. Please uninstall or close them.

Q：No sound can be heard, why?

A：Without connect audio input device. Please connect and try again.
B: Without enable audio function at the corresponding channel. Please check AUDIO
item to enable this function.

Q：Why doesn’t the device connect to wireless?

A: Check the statues of wireless router. Please make sure the router is open
B: Check the router and the device port. Please make the router setup is matched with
device port.
Page 50 IP CAMERA USER MUANUAL

9 Specification

Model Water-Proof IR Network Bullet Camera

Image Sensor 1/3”CMOS
Video Compression H.264
Audio Compression G711A
Image Size 1280 x 960
Shutter 1/25s~1/100000s
Low illumination 0 Lux (IR ON)
Lens 4mm (options: 6mm, 8mm, etc)
Resolution 720P(1280x960/1280x720), VGA(640x480), QVGA(320x240),
720P: 256bps～6144kbps (1~30fps)
720P: 256bps～6144kbps (1~10fps)
Stream
VGA: 128bps～2048kbps (1~30fps)
QVGA: 64kbps～512kbps(1~30fps)
Audio MIC IN*1
Network Protocol TCP/IP, DHCP, PPPoE, DDNS, SMTP, UPnP，RTSP,NTP
IR Range 10~20 m
Protection Grade IP66
Network Port RJ45
Remote Surveillance IE Browse、CMS remote control
Client Number Max 4
Power Supply DC12V/PoE
Working
-40°C ~50°C, 10%~90% humidity
Environment