Scribd
Upload
566 views

Negative 48 Volt Power What Why and How

Telecom and wireless networks use "negative" 48 volt DC power systems where the positive side of the battery is connected to ground rather than the negative side. This positive ground configuration was adopted to prevent corrosion caused by electrolysis that occurred in the negative ground systems used originally. However, it can cause confusion for installers since the roles of the red and black wires are reversed from typical systems. Proper precautions like consistent wire coloring and labeling are needed to avoid shorts or installing polarity backwards when working with positive ground "negative" 48 volt systems.

Uploaded by

RK K
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
566 views

Negative 48 Volt Power What Why and How

Telecom and wireless networks use "negative" 48 volt DC power systems where the positive side of the battery is connected to ground rather than the negative side. This positive ground configuration was adopted to prevent corrosion caused by electrolysis that occurred in the negative ground systems used originally. However, it can cause confusion for installers since the roles of the red and black wires are reversed from typical systems. Proper precautions like consistent wire coloring and labeling are needed to avoid shorts or installing polarity backwards when working with positive ground "negative" 48 volt systems.

Uploaded by

RK K
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

8/4/2021 “Negative” 48 Volt Power: What, Why and How | Newmar Powering the Network

“Negative” 48 Volt Power: What,


Why and How
Configuration Defined

Telecom and wireless


networks typically operate
on 48 volt DC power. But
unlike traditional 12 and 24
volt systems which have
the minus (-) side of the
battery connected to
ground (i.e. called negative
ground systems), telecom
batteries have the plus (+)
side of the battery
connected to ground, called
a positive ground system,
also designated as
“negative 48 volt”. In this
configuration, the minus
side of the battery becomes
the “hot” conductor and the
+ is no longer hot, rather it’s
at zero potential as it is
connected to ground and referred to as the “common” or ”return” wire. Despite its
complexity and propensity for confusion, described below, “neg” 48 volt is the
common choice in DC power for wireless networks.

History

Why is the positive side of the DC circuit connected to ground in telecom


applications versus negative ground used, as used, in automotive and other
industrial dc systems?

Back in the day, when Telephony equipment was being developed, 48 was the
chosen system voltage because it’s considered safe “low voltage”, and reduced
amperage requirement of equipment powered at this voltage. This allowed use of
smaller gauge wires, while still being capable of carrying power over long wire runs
with minimum voltage drop as a percentage of the operational voltage. The early
phone systems were configured as negative ground, however resulted in corrosion
on the conductors caused by electrolysis when the + wires were subjected to
moisture (you can see evidence of this condition on your car battery where the
corrosion builds up over time on the + terminal post). To remedy this problematic
condition, the systems were changed to positive ground and the destructive
galvanic corrosion was eliminated by the cathodic protection provided by grounding
the + side of the circuit.

Precautions

This positive ground configuration does not cause polarity to change, plus (+) is still
plus and carries a positive charge with respect to the negative (-) terminal or minus.
Many a short circuits have occurred when installers assume that when changing to
positive ground, polarity changes as a result, not true! Regardless of ground
reference, connecting (+) plus to (-) minus will still result in either a short circuit or
reverse polarity to equipment.

https://www.poweringthenetwork.com/uncategorized/negative-48-volt-power-what-why-and-how/ 1/2
8/4/2021 “Negative” 48 Volt Power: What, Why and How | Newmar Powering the Network

Another factor that can cause confusion (and potentially sparks) is use of red &
black colored wires. In negative ground systems, red is universally understood as
hot and +, in positive ground, this “red wire” is no longer hot, but is still +. So you
can imagine an installer standing there with a black wire in one hand and red wire
in the other looking at the input terminals on a “neg 48-volt” transmitter that are
marked “HOT” and “RTN” asking himself “What goes where?” Answer is: black to
plus and red to minus, which is a bit counter-intuitive. Thus, we recommend a
common color be used for both conductors and the wires labeled with the polarity.

Another word of caution on system integrations that mix positive and negative
ground equipment, Ground Isolation must be maintained between these operating
system to prevent short circuits and equipment compatibility issues. In addition,
there is the issue of continuity between chassis ground and system ground; they
can be common or may be isolated (called a floating ground).

https://www.poweringthenetwork.com/uncategorized/negative-48-volt-power-what-why-and-how/ 2/2

You might also like