EMD3 / UMD3N / IMD3A

Transistors

General purpose
(Dual digital transistors)
EMD3 / UMD3N / IMD3A

zFeatures zDimensions (Unit : mm)

1) Both the DTA114E chip and DTC114E chip in a EMT EMD3
or UMT or SMT package.
2) Mounting possible with EMT3 or UMT3 or SMT3 (6) (5) (4)
automatic mounting machines.
3) Transistor elements are independent, eliminating
interference. (1) (2) (3)

4) Mounting cost and area can be cut in half.

ROHM : EMT6 Each lead has same dimensions

Abbreviated symbol : D3

zStructure UMD3N
Epitaxial planar type
NPN / PNP silicon transistor (Built-in resistor type) (6) (5) (4)

The following characteristics apply to both the DTr1 and

(1) (2) (3)
DTr2, however, the “−” sign on DTr2 values for the PNP
type have been omitted. ROHM : UMT6 Each lead has same dimensions
EIAJ : SC-88
Abbreviated symbol : D3

zEquivalent circuits IMD3A

EMD3 / UMD3N IMD3A
(3) (2) (1) (4) (5) (6)
R1 R2 R1 R2 (4) (5) (6)

DTr1 DTr1
DTr2 DTr2
R1=10kΩ R1=10kΩ
R2=10kΩ R2 R1 R2 R1 R2=10kΩ
(4) (5) (6) (3) (2) (1)

(3) (2) (1)

ROHM : SMT6
Each lead has same dimensions
EIAJ : SC-74
zAbsolute maximum ratings (Ta=25°C)
Abbreviated symbol : D3
Parameter Symbol Limits Unit
Supply voltage VCC 50 V
−10
Input voltage VIN V
40
IO 50
Output current mA
IC (Max.) 100

Power EMD3, UMD3N 150 (TOTAL) ∗1

Pd mW
dissipation IMD3A 300 (TOTAL) ∗2
Junction temperature Tj 150 ˚C
Storage temperature Tstg −55 to +150 ˚C
∗1 120mW per element must not be exceeded.
∗2 200mW per element must not be exceeded.

Rev.D 1/3

This datasheet has been downloaded from http://www.digchip.com at this page

 EMD3 / UMD3N / IMD3A
Transistors

zElectrical characteristics (Ta=25°C)

Parameter Symbol Min. Typ. Max. Unit Conditions
VI (off) − − 0.5 VCC=5V, IO=100µA
Input voltage V
VI (on) 3 − − VO=0.3V, IO=10mA
Output voltage VO (on) − 0.1 0.3 V IO=10mA, II=0.5mA
Input current II − − 0.88 mA VI=5V
Output current IO (off) − − 0.5 µA VCC=50V, VI=0V
DC current gain GI 30 − − − VO=5V, IO=5mA
Transition frequency fT − 250 − MHz VCE=10V, IE=−5mA, f=100MHz ∗
Input resistance R1 7 10 13 kΩ −
Resistance ratio R2/R1 0.8 1 1.2 − −
∗ Transition frequency of the device

zPackaging specifications
Package Taping
Code T2R TR T108
Type
Basic ordering
8000 3000 3000
unit (pieces)
EMD3
UMD3N
IMD3A

zElectrical characteristic curves

DTr1 (NPN)
100 10m 1k
VO=0.3V VCC=5V VO=5V
5m
50 500
2m Ta=100˚C
OUTPUT CURRENT : Io (A)
INPUT VOLTAGE : VI (on) (V)

20 Ta=100˚C 25˚C
DC CURRENT GAIN : GI

1m 200
25˚C −40˚C
10 500µ −40˚C 100
5 Ta=−40˚C 200µ 50
25˚C
100˚C 100µ
2 50µ 20
1 20µ 10
500m 10µ 5
5µ
200m 2
2µ
100m 1µ 1
100µ 200µ 500µ 1m 2m 5m 10m 20m 50m 100m 0 0.5 1 1.5 2 2.5 3 100µ 200µ 500µ1m 2m 5m 10m 20m 50m100m
OUTPUT CURRENT : IO (A) INPUT VOLTAGE : VI (off) (V) OUTPUT CURRENT : IO (A)

Fig.1 Input voltage vs. output current Fig.2 Output current vs. input voltage Fig.3 DC current gain vs. output
(ON characteristics) (OFF characteristics) current

Rev.D 2/3
 EMD3 / UMD3N / IMD3A
Transistors

1
lO/lI=20
500m
OUTPUT VOLTAGE : VO (on) (V)

200m Ta=100˚C
25˚C
100m −40˚C

50m

20m

10m
5m

2m
1m
100µ 200µ 500µ 1m 2m 5m 10m 20m 50m 100m

OUTPUT CURRENT : IO (A)

Fig.4 Output voltage vs. output

current

DTr2 (PNP)
−100 −10m 1k
VO=−0.3V VCC=−5V VO=−5V
−50 −5m 500
Ta=100˚C Ta=100˚C
−2m
INPUT VOLTAGE : VI (on) (V)

25˚C 25˚C
OUTPUT CURRENT : Io (A)

−20 200

DC CURRENT GAIN : GI
−1m −40˚C −40˚C
−10 −500µ 100

−5 Ta=−40˚C −200µ 50
25˚C
100˚C −100µ
−2 −50µ 20
−1 −20µ 10

−500m −10µ 5
−5µ
−200m 2
−2µ
−100m −1µ 1
−100µ −200µ −500µ −1m −2m −5m −10m −20m −50m −100m 0 −0.5 −1 −1.5 −2 −2.5 −3 −100µ −200µ −500µ −1m −2m −5m −10m −20m −50m−100m
OUTPUT CURRENT : IO (A) INPUT VOLTAGE : VI (off) (V) OUTPUT CURRENT : IO (A)

Fig.5 Input voltage vs. output current Fig.6 Output current vs. input voltage Fig.7 DC current gain vs. output
(ON characteristics) (OFF characteristics) current

−1
lO/lI=20
−500m
Ta=100˚C
OUTPUT VOLTAGE : VO (on) (V)

−200m 25˚C
−40˚C
−100m

−50m

−20m

−10m
−5m

−2m
−1m
−100µ −200µ −500µ −1m −2m −5m −10m −20m −50m −100m

OUTPUT CURRENT : IO (A)

Fig.8 Output voltage vs. output

current

Rev.D 3/3
Appendix

Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.

The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level
of reliability and the malfunction of which would directly endanger human life (such as medical
instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers
and other safety devices), please be sure to consult with our sales representative in advance.
It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance
of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow
for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in
order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM
cannot be held responsible for any damages arising from the use of the products under conditions out of the
range of the specifications or due to non-compliance with the NOTES specified in this catalog.

Thank you for your accessing to ROHM product informations.

More detail product informations and catalogs are available, please contact your nearest sales office.

ROHM Customer Support System THE AMERICAS / EUROPE / ASIA / JAPAN

www.rohm.com Contact us : webmaster@ rohm.co. jp

TEL : +81-75-311-2121
Copyright © 2008 ROHM CO.,LTD. 21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan
FAX : +81-75-315-0172

Appendix1-Rev2.0