X-ENP

DATA SHEET
Siding and decking nail

May 2021
 X-ENP

X-ENP Siding and decking nail

Product data

Dimensions Material specifications

Carbon steel shank: HRC 58
Zinc coating: 8–16 μm
Recommended fastening tools
Tools: Single nail:
DX 76 F15, DX 76 PTR with X-ENP-19 L15
X-76-F15-PTR fastener guide
Tools: Collated nails:
DX 76 MX, DX 76 PTR X-ENP-19 L15 MX,
white magazine strip
DX 860-ENP, DX 9-ENP X-ENP-19 L15 MXR,
grey magazine strip

• For more details, please refer to the chapter

­Accessories and consumables compatibility in
the Direct Fastening Technology Manual (DFTM).
Approvals and certificates
ETA-04/0101 (Hilti-DX-DoP001), UL R13203, FM 3021719, ICC ESR-2197, ESR-2776
(USA), MLIT (Japan), ABS, LR 97/00077
• N
 ot all information presented in this product data sheet might be subject to ­approval /
certificate content. Please refer to approval / certificate for further ­information.

Applications
Examples

Roof decking Floor decking Wall liners

The intended use only comprises fastenings which are not directly exposed to external
weather conditions or moist atmospheres. For out-door applications, that can be ensured
by using SDK 2 sealing caps. During construction exposure to external atmosphere must
not exceed 6 months. Fastening of aluminum ­sheeting is generally recommended only for
indoor conditions.
05/2021 www.hilti.group 2
 X-ENP

Performance data
Characteristic loads – steel sheeting
Sheeting Trapezoidal profile Liner trays 1)
thickness (symmetric loading) (asymmetric loading)
tI [mm] Char. resistance Char. resistance
according to ETA-04/0101 keeping to ETA-04/0101
Shear Tension Shear Tension
nominal VRk [kN] NRk [kN] VRk [kN] NRk [kN]
0.75 4.70 6.30 3.30 4.40
0.88 5.40 7.20 3.80 5.00
1.00 6.00 8.00 4.20 5.60
1.13 7.00 8.40 4.90 5.90
1.25 8.00 8.80 5.60 6.20
1.50 8.60 8.80 6.00 6.20
1.75 8.60 8.80 6.00 6.20
2.00 8.60 8.80 6.00 6.20
2.50 8.60 8.80 6.00 6.20
• NRk and VRk are valid for steel sheet with minimum tensile strength ≥ 360 N/mm2 (≥ S280 EN 10346).
• For intermediate sheet thicknesses, use recommended load for next smaller thickness or linear interpolation.
1) Required load reduction is taken into account in accordance with EN 1993-1-3: 2006, section 8.3 (7) and
fig. 8.2. See also construction rules under spacings and edge distances.

Recommended loads – steel sheeting

Sheeting Trapezoidal profile Liner trays 1)
thickness (symmetric loading) (asymmetric loading)
tI [mm] Recommended loads Recommended loads
Shear Tension Shear Tension
nominal Vrec [kN] Nrec [kN] Vrec [kN] Nrec [kN]
0.75 2.50 3.35 1.75 2.35
0.88 2.90 3.85 2.00 2.70
1.00 3.20 4.25 2.25 3.00
1.13 3.75 4.50 2.65 3.15
1.25 4.25 4.70 3.00 3.30
1.50 4.60 4.70 3.20 3.30
1.75 4.60 4.70 3.20 3.30
2.00 4.60 4.70 3.20 3.30
2.50 4.60 4.70 3.20 3.30
• Nrec and Vrec are valid for steel sheet with minimum tensile strength ≥ 360 N/mm2 (≥ S280 EN 10346).
• For intermediate sheet thicknesses, use recommended load for next smaller thickness or linear interpolation.
• Recommended loads Nrec and Vrec are appropriate for Eurocode 1 wind loading design with a partial safety
factor γF =1.5 for wind load and a partial resistance factor γM = 1.25 for the fastening.
1) Required load reduction is taken into account in accordance with EN 1993-1-3: 2006, section 8.3 (7) and
fig. 8.2. See also construction rules under spacings and edge distances.

305/2021
www.hilti.group
 X-ENP

Recommended loads – aluminum sheeting1) with fu ≥ 210 N/mm2

Trapezoidal profile (symmetric loading)
Thickness Shear Tension
tI [mm] Vrec [kN] Nrec [kN]
0.60 0.75 0.35
0.70 0.90 0.50
0.80 1.00 0.65
0.90 1.20 0.80
1.00 1.30 0.95
1.20 1.55 1.30
1.50 1.85 1.45
2.00 2.55 1.90
1) Only recommended for indoor applications. Constraint forces and corrosion aspects have to be considered.
• For intermediate sheet thicknesses, use recommended load for next smaller thickness.
• Recommended loads Nrec and Vrec are appropriate for Eurocode 1 wind loading design with a partial safety
factor of γF =1.5 for wind load and a partial resistance factor γM = 1.25 for the fastening.

Recommended loads – other applications

Vrec [kN] Nrec [kN]
4.6 2.4
• Fastened parts: clips, brackets, etc.; thick steel parts (tl,max = 2.5 mm).
• Redundancy (multiple fastening) must be provided.
• The possibility of prying effects has to be considered
• Failure of the fastened part is not considered in these values of Nrec, Vrec.
• Valid for predominantly static loading
• Global factor of safety is ≥ 2 based on 5% fractile value

Design
Depending on the verification concept, the corresponding design criteria are given as following.
Working load concept Partial safety concept
Tensile loads NSk ≤ Nrec NSd ≤ NRd
Shear loads VSk ≤ Vrec VSd ≤ VRd

N-V Interaction
For combined tensile and shear forces on the fastener, a linear function has to be used.

( ) (
VSk + NSk ≤ 1
Vrec Nrec )

VSd + NSd ≤ 1
VRd NRd( ) ( )
with: with:
VSk, NSk unfactored characteristic load acting VSd, NSd Design load with γF = 1.5
on the fastening (= working load) VRd, NRd Design resistance of the fastening
Vrec, Nrec recommended (allowable) load with with γM = 1.25
γGLOB = 1.875 VRd = VRk / 1.25
NRd = αcycl NRk / 1.25
αcycl = 1.0 according to ETA-04/0101

05/2021 www.hilti.group 4
 X-ENP

Application recommendation

Thickness of base material

Steel thickness tII

tII ≥ 6 mm
tII

Thickness of fastened material

Σtl, tot ≤ 4.0 mm
Sheet thicknesses and overlap types

(a) (b) (c) (d)

single side lap end overlap side lap and end overlap

Nominal sheeting thickness tI Allowable overlap types

  0.63–1.00 mm a, b, c, d
> 1.00–1.25 mm a, c
> 1.25–2.50 mm a
With the above recommended sheet thickness and overlap types, it is not necessary to
take into account the effect of constraints due to temperature for steel grades up to S320
(EN 10346). For steel grade S350 (EN 10346) it shall be considered for design. Sheets of
grade S350 on base material tII ≥ 8 mm have been verified by Hilti, forces of constraint can
be neglected.

505/2021
www.hilti.group
 X-ENP

Spacing and edge distances (mm)

Steel base material
7 7

15 10

Trapezoidal profiles

45
20
20
Centre fastenings in Clearance to end of sheet Double fastenings (asymmetric)
ribs Note: R
 educe tensile resistance per fastener
to 0.7 NRk or 0.7 Nrec.

Liner trays

(1)
c
c 20 80

75
c
90°
Clearance to side of sheet Clearance to side of sheet Clearance to end of sheet Fastener spacing along
sheet
When driving the fastener, the fastening tool needs to
be positioned perpendicular to the surface.
If c > 75 mm, it is recommended to drive an additional
fastener at the other side of the tray. This additional
fastener is indicated with (1) in the graph above.

05/2021 www.hilti.group 6
 X-ENP

Application limit

X-ENP-19 with DX 76, DX 76 PTR, DX 860-ENP and DX 9-ENP

>22

21

20

10

18

17

16
Steel thickness tII [mm]

15
Applicable
14 range of base
materials
13

12

11

10

9
S 235
8
S 275
7
S 355
6
350 400 450 500 550 600 650 700 750
Steel strength Rm [N/mm2]

Corrosion information
•T  he intended use only comprises fastenings which are not directly exposed to external
­weather conditions or moist atmospheres.
•F  or outdoor applications that can be ensured by using SDK 2 sealing caps.
•D  uring construction exposure to external atmosphere must not exceed 6 months.
•F  astening of aluminum sheeting is generally recommended only for indoor conditions.
• For more details, please refer to following technical document: Hilti Corrosion
Handbook.

705/2021
www.hilti.group
 X-ENP

Fastener program and system recommendation

Fasteners Tools Fastener guide

Designation Item no. Designation Designation
Single nail: X-ENP-19 L15 283506 DX 76 PTR X-76-F15-PTR
DX 76 F15
Collated nails: X-ENP-19 L15 MX, 283507 DX 76 PTR
white magazine strip DX 76 MX
X-ENP-19 L15 MXR, 283508 DX 860-ENP
grey magazine strip
Piston: X-76-P-ENP-PTR DX 76 PTR
X-76-P-ENP DX 76
DX 860-ENP
X-9-ENP kit DX 9-ENP

Cartridge selection and tool energy setting

DX 76, DX 860-ENP, DX 9-ENP DX 76 PTR

>20 >20

19 19
Red 4
18 or Black 4 18
Black 2
17 17

16 16
Steel thickness tII [mm]
Steel thickness tII [mm]

Red 4
15 15
or Black 4
14 14 Black 2

13 Red 3 13
or Black 3
12 Black 1 12

11 11

10 10
Blue 4 or Red 4 or Blue 4
9 9 or Red 4
Red 2 Black 2
Red 2
8 8
Blue 3
7 Blue 3 Red 3 7 or Red 3
Red 1
6 6
S 235 S 355 S 355
S 235 S 275
Fine adjustment by installation tests on site.
Note for S275:
Start with recommendation for S355. In case of too much energy: reduction of tool energy
setting or change of cartridge colour till correct nail head stand-offs hNVS are achieved.

05/2021 www.hilti.group 8
 X-ENP

Quality assurance

Fastening inspectionhNVS

ΣtI,tot ≤ 4 mm
tII

hNVS = 8.2–9.8 mm for tI,tot ≤ 4 mm

In order to allow the steel sheeting to be
in direct contact with the steel supporting
structure in the area of connections the
X-ENP-19 fastener should be installed
≥ 30mm away from the edges of insulation /
isolation tapes that are ≤ 3 mm thick.

X-ENP-19 L15 X-ENP-19 L15 X-ENP-19 L15

Max Max Max

Min Min Min

hNVS = 8.2–9.8 mm hNVS > 9.8 mm hNVS < 8.2 mm

(washers are not compressed) (washers are strongly damaged by
the tool piston)

Visible inspection:
Properly driven fastener.
Piston mark clearly visible on the
washer.

905/2021
www.hilti.group