5/20/23, 9:56 PM Thin Cylinders - Strength of Materials Questions and Answers - Sanfoundry

es on “Thin Cylinders”.

1. If the thickness of plate is negligible when compared to the diameter of the cylindrical, then it is called __________
a) Thick cylinder
b) Thin cylinder
c) Hoop cylinder
d) Circumferential cylinder
View Answer

Answer: b
Explanation: The thickness of plate is negligible when compared to the diameter of the cylindrical shell, and then it can be termed as a thin
cylinder. The radius stress in the cylinder walls is negligible.

2. In thin cylinders, the thickness should be ____________ times of internal diameter.

a) 1/20
b) 1/15
c) 1/30
d) 1/40
View Answer

Answer: a
Explanation: In thin shells, the stress distribution over the thickness of the material is assumed to be uniform and the wall thickness is equal
to or less than 1/ 20 of the internal diameter.

3. Oil tanks, steam boilers, gas pipes are examples of _____________

a) Thick shells
b) Thin cylinders
c) Hoop cylinders
d) Longitudinal cylinders
View Answer

Answer: b
Explanation: In thin cylindrical shells, the stresses are uniformly distributed throughout the wall. The type of stresses developed in thin
cylinders is hoop stress and longitudinal stress. Ex: water supply mains, oil tanks, steam boilers and gas pipes.

Sanfoundry Certification Contest of the Month is Live. 100+ Subjects. Participate Now!

advertisement

4. In _________ shells, the stress distribution is not uniform over the thickness of the material.
a) Thick
b) Thin
c) Hoop
d) Circumferential
View Answer

Answer: a
Explanation: A cylinder in which the wall thickness is greater than 1 / 20 of internal diameter it is called the thick cylinder.
t>d/20. In thick shells, the stress distribution is not uniform over the thickness of the material.

https://www.sanfoundry.com/strength-materials-questions-answers-thin-cylinders/ 1/4
5/20/23, 9:56 PM Thin Cylinders - Strength of Materials Questions and Answers - Sanfoundry
5. Hydraulic radius is denoted by _________
a) T
b) A
c) R
d) N
View Answer

Answer: c
Explanation: Hydraulic radius is the ratio of wetted area to the wetted perimeter. It is also known as hydraulic mean depth. It is denoted by
“R”.
R = A/P.

Check this: Metallurgical Engineering Books | Mechanical Engineering MCQs

6. Hydraulic depth is a ratio of wetted area to _____

a) Bottom width
b) Top width
c) Diameter
d) Radius
View Answer

Answer: b
Explanation: Hydraulic depth is the ratio of wetted area to the top with (T). It is denoted by D
D = A/T.

7. What is the hydraulic depth (D) of a rectangular section?

a) y
b) 1/3 y
c) y2
d) y/5
View Answer

Answer: a
Explanation: The hydraulic depth (D) of a rectangular section is y.

Section Hydraulic depth (D)

Rectangle y

Trapezoid (B+Zy)y / B+2zy

1⁄  y
Triangle 2

advertisement

8. In manning’s formula, V = 1/n×m2/3×i1/2. N stands for ___________

a) Coefficient of viscosity
b) Coefficient of rugosity
c) Coefficient of runoff
d) Coefficient of friction
View Answer
https://www.sanfoundry.com/strength-materials-questions-answers-thin-cylinders/ 2/4
5/20/23, 9:56 PM Thin Cylinders - Strength of Materials Questions and Answers - Sanfoundry
Answer: b
Explanation: In 1889, manning presented a formula according to which the mean velocity of uniform flow in a channel is V = 1/n × m 2/3 ×
i1/2.
Where n = coefficient of rugosity.

9. What is the coefficient of rugosity for brick lined surface?

a) 0.011
b) 0.012
c) 0.015
d) 0.013
View Answer

Answer: c
Explanation: The coefficient of rugosity for brick lined surface is 0.015.

Channel Surface Coefficient of Rugosity (n)

Asbestos cement 0.011

Brick 0.015

Cast Iron 0.012

Galvanised Iron 0.016

advertisement

10. Most economical section is also called as __________

a) Most active section
b) Most effective section
c) Most efficient section
d) Superior section
View Answer

Answer: c
Explanation: A channel is said to be the most economical if it gives the maximum discharge under given cross-sectional area, bottom slope
and roughness. The most economical section is also known as the most efficient section.

11. For most economical section __________ should be minimum.

a) P
b)A
c) R
d)N
View Answer

Answer: a
Explanation: A channel discharges larger if the hydraulic radius is maximum. The hydraulic radius will be maximum when the wetted
perimeter is minimum for a given area. Hence, for most economical section the wetted perimeter should be minimum.

12. A rectangular channel has cross sectional area of 50 m2. If the channel section is to be most economical calculate the depth. Take B =
10m.
a) 10 m
b) 5 m
c) 8 m
https://www.sanfoundry.com/strength-materials-questions-answers-thin-cylinders/ 3/4
5/20/23, 9:56 PM Thin Cylinders - Strength of Materials Questions and Answers - Sanfoundry
d) 12 m
View Answer

Answer: b
Explanation: Let y be the depth of flow of the channel. For most economical section y = B/2.
Cross-section area of flow A = By
y= 50/10
y= 5 m.

13. _________ are used to change the water level in a canal.

a) Sluice gates
b) Lock gates
c) Check gates
d) Scour gates
View Answer

Answer: b
Explanation: Gates which are used to change the water level in a canal or a river are known as lock gates. If a canal or a river has a vertical
fall at any section, it is necessary to raise or lower the water level in order to transfer the boat from upper water level to lower one.

14. The flow of water is controlled in hydraulic structures by ____________

a) Sluice gates
b) Check gates
c) Lock gates
d) Drain gates
View Answer

Answer: a
Explanation: In hydraulic structures, the openings are provided to carry water from its storage place to place of utilisation. The flow of water
through such openings is controlled by means of sluice gates.

15. The units of discharge are _____________

a) m/s
b) m2/s
c) m3/s
d) m
View Answer

Answer: c

https://www.sanfoundry.com/strength-materials-questions-answers-thin-cylinders/ 4/4