US Army
Corps
of Engineers
Fort Worth District
Design-Bid-Build
Renovation of Bldg 615 for Army
Band
Joint Base Fort Sam Houston AR North
San Antonio, TX
W9126G19B3286
August 2019
PROJECT TABLE OF CONTENTS
DIVISION 00 - PROCUREMENT AND CONTRACTING REQUIREMENTS
00 11 00.01 SOLICITATION, OFFER AND AWARD, SF-1442
00 11 00.02 CONTRACT LINE ITEM SCHEDULE
00 21 00 [INSTRUCTIONS, CONDITIONS, AND NOTICES TO OFFERORS]
00 21 30 SITE VISITS
00 45 00 REPRESENTATIONS AND CERTIFICATIONS
00 72 00 CONTRACT CLAUSES
00 73 00 SPECIAL CONTRACT REQUIREMENTS
00 73 46 WAGE DETERMINATION SCHEDULE
DIVISION 01 - GENERAL REQUIREMENTS
01 00 00.00 44 CONSTRUCTION SCHEDULE
01 32 01.00 10 PROJECT SCHEDULE
01 33 00 SUBMITTAL PROCEDURES
01 35 13.01 44 SPECIAL PROJECT PROCEDURES FOR JOINT BASE SAN
ANTONIO/FORT SAM HOUSTON
01 35 13.10 00 SPECIAL PROJECT PROCEDURES - SURVEYING
01 35 13.20 00 SPECIAL PROJECT PROCEDURES - CAD
01 35 13.30 00 SPECIAL PROJECT PROCEDURES - GIS
01 35 26 GOVERNMENTAL SAFETY REQUIREMENTS
01 42 00 SOURCES FOR REFERENCE PUBLICATIONS
01 45 00.00 10 QUALITY CONTROL
01 45 00.15 10 RESIDENT MANAGEMENT SYSTEM CONTRACTOR MODE(RMS CM)
01 50 00 TEMPORARY CONSTRUCTION FACILITIES AND CONTROLS
01 57 20 ENVIRONMENTAL PROTECTION
01 62 35 RECYCLED / RECOVERED MATERIALS
01 72 00.00 44 ALTERATIONS TO EXISTING FACILITIES
01 74 19 CONSTRUCTION WASTE MANAGEMENT AND DISPOSAL
01 78 00 CLOSEOUT SUBMITTALS
01 78 23 OPERATION AND MAINTENANCE DATA
01 91 00.15 TOTAL BUILDING COMMISSIONING
DIVISION 02 - EXISTING CONDITIONS
02 41 00 DEMOLITION
02 82 13.00 10 ASBESTOS ABATEMENT
02 83 13.00 20 LEAD IN CONSTRUCTION
DIVISION 03 - CONCRETE
03 30 00 CAST-IN-PLACE CONCRETE
DIVISION 04 - MASONRY
04 03 00 CONSERVATION TREATMENT FOR PERIOD MASONRY
04 20 00 UNIT MASONRY
DIVISION 05 - METALS
05 12 00 STRUCTURAL STEEL
05 30 00 STEEL DECKS
05 40 00 COLD-FORMED METAL FRAMING
05 50 13 MISCELLANEOUS METAL FABRICATIONS
Page 1
05 51 33 METAL LADDERS
05 52 00 METAL RAILINGS
DIVISION 06 - WOOD, PLASTICS, AND COMPOSITES
06 10 00 ROUGH CARPENTRY
06 20 00 FINISH CARPENTRY
06 41 16.00 10 PLASTIC-LAMINATE-CLAD ARCHITECTURAL CABINETS
06 60 00 CELLULAR PVC FABRICATIONS
06 61 16 SOLID SURFACING FABRICATIONS
DIVISION 07 - THERMAL AND MOISTURE PROTECTION
07 05 23 PRESSURE TESTING AN AIR BARRIER SYSTEM FOR AIR TIGHTNESS
07 11 13 BITUMINOUS DAMPPROOFING
07 13 53 ELASTOMERIC SHEET WATERPROOFING
07 21 13 BOARD AND BLOCK INSULATION
07 21 16 MINERAL FIBER BLANKET INSULATION
07 22 00 ROOF AND DECK INSULATION
07 24 00 EXTERIOR INSULATION AND FINISH SYSTEMS
07 27 10.00 10 BUILDING AIR BARRIER SYSTEM
07 27 19.01 SELF-ADHERING AIR BARRIERS
07 27 36 SPRAY FOAM AIR BARRIERS
07 30 10 ROOFING UNDERLAYMENT
07 41 13 METAL ROOF PANELS
07 54 19 POLYVINYL-CHLORIDE ROOFING
07 60 00 FLASHING AND SHEET METAL
07 84 00 FIRESTOPPING
07 92 00 JOINT SEALANTS
DIVISION 08 - OPENINGS
08 11 13 STEEL DOORS AND FRAMES
08 14 00 WOOD DOORS
08 31 00 ACCESS DOORS AND PANELS
08 34 73 SOUND CONTROL DOOR ASSEMBLIES
08 51 13 ALUMINUM WINDOWS
08 71 00 DOOR HARDWARE
08 81 00 GLAZING
08 91 00 METAL WALL LOUVERS
DIVISION 09 - FINISHES
09 01 90.50 PREPARATION OF HISTORIC WOOD AND METAL SURFACES FOR
PAINTING
09 22 00 SUPPORTS FOR PLASTER AND GYPSUM BOARD
09 29 00 GYPSUM BOARD
09 30 10 CERAMIC, QUARRY, AND GLASS TILING
09 51 00 ACOUSTICAL CEILINGS
09 65 00 RESILIENT FLOORING
09 68 00 CARPETING
09 90 00 PAINTS AND COATINGS
DIVISION 10 - SPECIALTIES
10 11 00 VISUAL DISPLAY UNITS
10 14 00.20 INTERIOR SIGNAGE
10 21 13 TOILET COMPARTMENTS
Page 2
10 26 00 WALL AND DOOR PROTECTION
10 28 13 TOILET ACCESSORIES
10 51 13 METAL LOCKERS
DIVISION 12 - FURNISHINGS
12 21 00 WINDOW BLINDS
12 50 00.13 10 FURNITURE AND FURNITURE INSTALLATION
12 59 00 SYSTEMS FURNITURE
DIVISION 14 - CONVEYING EQUIPMENT
14 24 23 HYDRAULIC PASSENGER ELEVATORS
DIVISION 21 - FIRE SUPPRESSION
21 13 13.00 10 WET PIPE SPRINKLER SYSTEM, FIRE PROTECTION
DIVISION 22 - PLUMBING
22 00 00 PLUMBING, GENERAL PURPOSE
22 07 19.00 40 PLUMBING PIPING INSULATION
DIVISION 23 - HEATING, VENTILATING, AND AIR CONDITIONING (HVAC)
23 00 00 AIR SUPPLY, DISTRIBUTION, VENTILATION, AND EXHAUST SYSTEMS
23 01 30.41 HVAC SYSTEM CLEANING
23 03 00.00 20 BASIC MECHANICAL MATERIALS AND METHODS
23 05 15 COMMON PIPING FOR HVAC
23 05 48.00 40 VIBRATION AND SEISMIC CONTROLS FOR HVAC PIPING AND
EQUIPMENT
23 05 93 TESTING, ADJUSTING, AND BALANCING FOR HVAC
23 07 00 THERMAL INSULATION FOR MECHANICAL SYSTEMS
23 09 23 BACNET DIGITAL CONTROLS (DDC) SYSTEM
23 11 25 FACILITY GAS PIPING
23 21 23 HYDRONIC PUMPS
23 23 00 REFRIGERANT PIPING
23 31 13.00 40 METAL DUCTS
23 34 23.00 40 HVAC POWER VENTILATORS
23 37 13.00 40 DIFFUSERS, REGISTERS, AND GRILLS
23 52 00 HEATING BOILERS
23 54 16.00 10 HEATING SYSTEM; GAS-FIRED HEATERS
23 64 10 WATER CHILLERS, VAPOR COMPRESSION TYPE
23 73 13.00 40 MODULAR INDOOR CENTRAL-STATION AIR-HANDLING UNITS
23 82 19.00 40 FAN COIL UNITS
DIVISION 26 - ELECTRICAL
26 00 00.00 20 BASIC ELECTRICAL MATERIALS AND METHODS
26 05 00.00 40 COMMON WORK RESULTS FOR ELECTRICAL
26 05 19.10 10 INSULATED WIRE AND CABLE
26 05 71.00 40 LOW VOLTAGE OVERCURRENT PROTECTIVE DEVICES
26 09 23.00 40 LIGHTING CONTROL DEVICES
26 20 00 INTERIOR DISTRIBUTION SYSTEM
26 24 13 SWITCHBOARDS
26 24 16.00 40 PANELBOARDS
26 28 01.00 10 COORDINATED POWER SYSTEM PROTECTION
Page 3
26 41 00 LIGHTNING PROTECTION SYSTEM
26 51 00 INTERIOR LIGHTING
26 52 00.00 40 EMERGENCY LIGHTING
26 56 00 EXTERIOR LIGHTING
DIVISION 27 - COMMUNICATIONS
27 05 14.00 10 CABLE TELEVISION PREMISES DISTRIBUTION SYSTEM
27 05 28.36 40 CABLE TRAYS FOR COMMUNICATIONS SYSTEMS
27 05 29.00 10 PROTECTIVE DISTRIBUTION SYSTEM (PDS) FOR SIPRNET
COMMUNICATION SYSTEMS
27 10 00 BUILDING TELECOMMUNICATIONS CABLING SYSTEM
27 13 23.00 40 COMMUNICATIONS OPTICAL BACKBONE CABLING
27 21 00.00 20 INTERCOMMUNICATION SYSTEM
27 21 00.00 40 INTERCOMMUNICATION SYSTEM
27 21 10.00 40 FIBER OPTIC DATA TRANSMISSION SYSTEM
DIVISION 28 - ELECTRONIC SAFETY AND SECURITY
28 05 26.00 40 GROUNDING AND BONDING FOR ELECTRONIC SAFETY AND SECURITY
28 08 10 ELECTRONIC SECURITY SYSTEM ACCEPTANCE TESTING
28 10 05 ELECTRONIC SECURITY SYSTEMS (ESS)
28 31 76 INTERIOR FIRE ALARM AND MASS NOTIFICATION SYSTEM
DIVISION 31 - EARTHWORK
31 00 00 EARTHWORK
DIVISION 32 - EXTERIOR IMPROVEMENTS
32 12 13 BITUMINOUS TACK AND PRIME COATS
32 12 16 HOT-MIX ASPHALT (HMA) FOR ROADS
32 16 13 CONCRETE SIDEWALKS AND CURBS AND GUTTERS
32 92 23 SODDING
DIVISION 33 - UTILITIES
33 11 00 WATER UTILITY DISTRIBUTION PIPING
33 30 00 SANITARY SEWERS
ATTACHMENTS
A. HAZMAT SURVEY
-- End of Project Table of Contents --
Page 4
Bldg 615 FSH19B615
SECTION 12 21 00
WINDOW BLINDS
PART 1 GENERAL
1.1 SUMMARY
Provide window treatment, conforming to NFPA 701, complete with necessary
brackets, fittings, and hardware. Provide each window treatment type as a
complete unit in accordance with paragraph WINDOW TREATMENT PLACEMENT
SCHEDULE. Mount and operate equipment in accordance with manufacturer's
instructions. Completely cover windows to receive a treatment.
1.2 REFERENCES
The publications listed below form a part of this specification to the
extent referenced. The publications are referred to in the text by basic
designation only.
NATIONAL FIRE PROTECTION ASSOCIATION (NFPA)
NFPA 701 (2015) Standard Methods of Fire Tests for
Flame Propagation of Textiles and Films
SCIENTIFIC CERTIFICATION SYSTEMS (SCS)
SCS SCS Global Services (SCS) Indoor Advantage
UNDERWRITERS LABORATORIES (UL)
UL 2818 (2013) GREENGUARD Certification Program
For Chemical Emissions For Building
Materials, Finishes And Furnishings
1.3 SUBMITTALS
Government approval is required for submittals with a "G" designation;
submittals not having a "G" designation are for Contractor Quality Control
approval. Submittals with an "S" are for inclusion in the Sustainability
eNotebook, in conformance to Section 01 33 29 SUSTAINABILITY REPORTING.
Submit the following in accordance with Section 01 33 00 SUBMITTAL
PROCEDURES
SD-02 Shop Drawings
Installation
SD-03 Product Data
Window Blinds; G
Installation
SECTION 12 21 00 Page 1
Bldg 615 FSH19B615
SD-04 Samples
Window Blinds; G
Valance; G
SD-06 Test Reports
Window Blinds
SD-07 Certificates
Indoor Air Quality for window blinds; S
SD-08 Manufacturer's Instructions
Window Blinds; G
SD-10 Operation and Maintenance Data
Window Blinds; G
1.4 CERTIFICATIONS
1.4.1 Indoor Air Quality Certifications
Provide products certified to meet indoor air quality requirements by
UL 2818 Greenguard , SCS Global Services Indoor Advantage Gold or provide
certification or validation by other third-party program that products meet
the requirements of this Section. Provide current product certification
documentation from certification body.
1.5 DELIVERY, STORAGE, AND HANDLING
Deliver components to the jobsite in the manufacturer's original packaging
with the brand or company name, item identification, and project reference
clearly marked. Store components in a dry location that is adequately
ventilated and free from dust, water, or other contaminants and has easy
access for inspection and handling. Store materials flat in a clean dry
area with temperature maintained above 50 degrees F. Do not open
containers until needed for installation unless verification inspection is
required.
1.6 WARRANTY
Provide manufacturer's standard performance guarantees or warranties that
extend beyond a 1 year period.
PART 2 PRODUCTS
2.1 WINDOW BLINDS
Provide each blind, including hardware, accessory items, mounting brackets
and fastenings, as a complete unit produced by one manufacturer. All parts
must be one color, unless otherwise indicated, to match the color of the
blind slat. Treat steel features for corrosion resistance. Submit samples
of each type and color of window treatment. Provide aluminum horizontal
louver blind slats 6 inch in length for each color. Provide 6 inch sample
SECTION 12 21 00 Page 2
Bldg 615 FSH19B615
of horizontal blind slats in each color specified. Also submit results of
Fire resistance, Flame Spread, and Smoke contribution tests.
Provide certification of indoor air quality for window blinds.
2.1.1 Horizontal Blinds
Provide horizontal blinds with 1 inch slats. Blind units must be capable
of nominally 180 degree partial tilting operation and full-height raising.
Blinds must be inside mount. Provide tapes for 2 inch slats with
longitudinal reinforced vinyl plastic in 1-piece turn ladder construction.
Tapes for 1 inch slats must be braided polyester or nylon.
2.1.1.1 Head Channel and Slats
Provide head channel made of steel or aluminum with corrosion-resistant
finish nominal 0.024 inch for 1 inch slats. Provide slats of aluminum, not
less than 0.008 inch thick, and of sufficient strength to prevent sag or
bow in the finished blind. Provide a sufficient amount of slats to assure
proper control, uniform spacing, and adequate overlap. Enclose all
hardware in the headrail.
2.1.1.2 Controls
The slats shall be tilted by a transparent tilting wand, hung vertically by
its own weight, and shall swivel for easy operation. Provide a tilter
control of enclosed construction. Provide moving parts and mechanical
drive made of compatible materials which do not require lubrication during
normal expected life. The tilter shall tilt the slats to any desired angle
and hold them at that angle so that any vibration or movement of ladders
and slats will not drive the tilter and change the angle of slats. Include
a mechanism to prevent over tightening. Provide a wand of sufficient
length to reach to within 5 feet of the floor.
2.1.1.3 Intermediate Brackets
Provide intermediate brackets for installation, as recommended by the
manufacturer, of blinds over 48 inch wide.
2.1.1.4 Bottom Rail
Provide bottom rail made of corrosion-resistant steel with factory applied
finish. Provide closed oval shaped bottom rail with double-lock seam for
maximum strength. Bottom rail and end caps to match slats in color.
2.1.1.5 Braided Ladders
Provide braided ladders of 100 percent polyester yarn, color to match the
slat color. Space ladders 15.2 slats per foot of drop in order to provide
a uniform overlap of the slats in a closed position.
2.1.1.6 Hold-Down Brackets
Provide universal type hold-down brackets for sill or jamb mount where
indicated on placement list.
2.2 COLOR
Provide color, pattern and texture in accordance with Section 09 06 00
SECTION 12 21 00 Page 3
Bldg 615 FSH19B615
SCHEDULES FOR FINISHES
PART 3 EXECUTION
3.1 EXAMINATION
After becoming familiar with details of the work, verify all dimensions in
the field, and advise the Contracting Officer of any discrepancy before
performing the work.
3.2 WINDOW TREATMENT PLACEMENT SCHEDULE
All exterior windows include all perimeter windows..
3.3 INSTALLATION
Do not install building construction materials that show visual evidence of
biological growth.
Submit drawings showing fabrication and installation details. Show layout
and locations of track, direction of draw, mounting heights, and details.
3.3.1 Horizontal Blinds
Perform installation of Horizontal Blinds in accordance with the approved
detail drawings and manufacturer's installation instructions. Install
units level, plumb, secure, and at proper height and location relative to
window units. Provide and install supplementary or miscellaneous items in
total, including clips, brackets, or anchorages incidental to or necessary
for a sound, secure, and complete installation. Do not start installation
until completion of room painting and finishing operations.
3.4 CLEAN-UP
Upon completion of the installation, free window treatments from soiling,
damage or blemishes; and adjust them for form and appearance and proper
operating condition. Repair or replace damaged units as directed by the
Contracting Officer. Isolate metal parts from direct contact with
concrete, mortar, or dissimilar metals. Ensure blinds installed in
recessed pockets can be removable without disturbing the pocket. The
entire blind, when retracted, must be contained behind the pocket. For
blinds installed outside the jambs and mullions, overlap each jamb and
mullion 0.75 inch or more when the jamb and mullion sizes permit. Include
all hardware, brackets, anchors, fasteners, and accessories necessary for a
complete, finished installation.
-- End of Section --
SECTION 12 21 00 Page 4
Bldg 615 FSH19B615
SECTION 12 50 00.13 10
FURNITURE AND FURNITURE INSTALLATION
PART 1 GENERAL
Purchase and install furniture as identified within this specification.
This specification section includes a Furniture, Fixtures and Equipment
(FF&E) Package attachment.
The requirements of this specification also apply to systems furniture
unless otherwise specified in Section 12 59 00 Systems Furniture.
1.1 REFERENCES
The publications listed below form a part of this specification to the
extent referenced. The publications are referred to within the text by the
basic designation only.
AMERICAN SOCIETY OF HEATING, REFRIGERATING AND AIR-CONDITIONING
ENGINEERS (ASHRAE)
ASHRAE 90.1 - IP (2016; ERTA 1-8 2017; INT 1-5 2017) Energy
Standard for Buildings Except Low-Rise
Residential Buildings
ASTM INTERNATIONAL (ASTM)
ASTM D4157 (2013; R 2017) Standard Test Method for
Abrasion Resistance of Textile Fabrics
(Oscillatory Cylinder Method)
ASTM E84 (2017) Standard Test Method for Surface
Burning Characteristics of Building
Materials
BIFMA INTERNATIONAL (BIFMA)
ANSI/BIFMA X5.1 (2017) American National Standards For
Office Furnishings - General Purpose
Office Chairs
ANSI/BIFMA X5.3 (2007; R2012) American National Standards
For Office Furnishings - Vertical Files
ANSI/BIFMA X5.4 (2012) American National Standards For
Office Furnishings - Lounge Seating
ANSI/BIFMA X5.5 (2014) American National Standards For
Office Furnishings -Desk Products
ANSI/BIFMA X5.6 (2016) American National Standards For
Office Furnishings -Panel Systems
ANSI/BIFMA X5.9 (2012) American National Standards For
Office Furnishings - Storage Units
SECTION 12 50 00.13 10 Page 1
Bldg 615 FSH19B615
NATIONAL FIRE PROTECTION ASSOCIATION (NFPA)
NFPA 101 (2018; TIA 18-1) Life Safety Code
NFPA 265 (2015) Standard Methods of Fire Tests for
Evaluating Room Fire Growth Contribution
of Textile Coverings on Full Height Panels
and Walls
TELECOMMUNICATIONS INDUSTRY ASSOCIATION (TIA)
TIA-568-C.2 (2009; Errata 2010; Add 2 2014; Add 1
2016) Balanced Twisted-Pair
Telecommunications Cabling and Components
Standards
U.S. NATIONAL ARCHIVES AND RECORDS ADMINISTRATION (NARA)
36 CFR 1191 Americans with Disabilities Act (ADA)
Accessibility Guidelines for Buildings and
Facilities; Architectural Barriers Act
(ABA) Accessibility Guidelines
UNDERWRITERS LABORATORIES (UL)
UL 723 (2008; Reprint Aug 2013) Test for Surface
Burning Characteristics of Building
Materials
1.2 SUBMITTALS
Government approval is required for submittals with a "G" designation;
submittals not having a "G" designation are for Contractor Quality Control
approval. Submittals with an "S" are for inclusion in the Sustainability
eNotebook, in conformance to Section 01 33 29 SUSTAINABILITY REPORTING.
Submit the following in accordance with Section 01 33 00 SUBMITTAL
PROCEDURES:
SD-01 Preconstruction Submittals
Storage Location; G
SD-02 Shop Drawings
Installation Drawings; G
Grommet, Power and Communication Units, and Wire Management
Locations; G
SD-03 Product Data
Product Data; G
Product Style Options; G
SD-04 Samples
Fabric and Finishes; G
SECTION 12 50 00.13 10 Page 2
Bldg 615 FSH19B615
SD-07 Certificates
Authorized Dealer; G
Certified Furniture Installers; G
Licensed Electrician; G
Certified Telecommunications Installer; G
Manufacturer's Certification; G
Warranty; G
SD-10 Operation and Maintenance Data
Furniture, Data Package 1; G
SD-11 Closeout Submittals
Energy Efficient Equipment; S
Reduced VOC's for Furniture; S
Recycled Content of Furniture; S
Bio-Based Content of Furniture; S
1.3 SERVICES
Provide services to include furniture purchase, field measuring,
installation drawings, shipping and delivery coordination, receiving,
inspection, submitting and processing freight and warranty claims,
unpacking, storing, assembly, installation and other related activities or
tasks for a complete and functional installation. Reference Section
01 45 00.00 10 QUALITY CONTROL for inspection requirements. The
Contracting Officer must be allowed to participate in inspections. Develop
project timelines and establish shipping, receiving and installation dates
that coordinate with the building construction schedule. Hold at a minimum
weekly team meetings to brief the project team, include the Contracting
Officer. Notify the Contracting Officer immediately of any scheduling
problems, discontinued furniture items including fabrics and finishes, or
other conditions which may cause delays, and recommend available
substitutes, solutions, and provide updated timeline to coordinate with
building construction schedule. Substitutes and solutions must comply with
the specification and be approved by the Contracting Officer.
1.4 FURNITURE PURCHASE
Purchase furniture, including checking accuracy of all acknowledgements and
schedules from manufacturers and making necessary corrections to insure
that the manufacturer has a correct understanding of the order and
requirement. Purchase furniture from the open market. The furniture
provided needs to be available on the GSA Schedules to assist the User with
future purchases. GSA information is provided FOR INFORMATIONAL PURPOSES
ONLY. It is encouraged to solicit and provide GSA pricing on furniture.
Compete the furniture purchase by obtaining a minimum of (3) separate
proposals. Furniture is subject to FAR clause 52.236-5 Materials and
Workmanship. If necessary to meet project timeline requirements, furniture
SECTION 12 50 00.13 10 Page 3
Bldg 615 FSH19B615
may be purchased using manufacturers quick-ship programs or by coordinating
factory times.
1.5 ALTERNATE DESIGN
When a manufacturer's product is unable to provide desk and workstation
configurations and filing/storage that conform exactly to the furniture
layouts shown in the contract drawings and specifications, alternate
designs may be submitted for consideration by the Contracting Officer.
Alternate designs must meet or exceed the following criteria. Alternate
designs that are submitted but do not meet these criteria will be rejected.
1.5.1 Desk and Workstation Size and Configuration
The alternate design must provide desks and workstations of the same basic
size and configuration shown, with only the sizes of the individual
components within the desk and workstation changed to meet the standard
product of the manufacturer.
1.5.2 Filing and Storage Size and Configuration
The alternate design must provide filing and storage of the same basic size
and configuration shown, with only the size changed to meet the standard
product of the manufacturer. The storage capacity must not be reduced.
1.5.3 Furniture Requirements
The furniture provided must comply with the drawings, specifications, and
the requirements identified in the FF&E Package Attachment.
1.5.4 Layout
The storage capacity, number of desks and workstations, number of persons
accommodated, width of aisles, and functionality must be maintained.
Layout must comply with NFPA 101 and 36 CFR 1191.
1.6 AUTHORIZED DEALER, CERTIFIED FURNITURE INSTALLERS, LICENSED ELECTRICIAN
AND CERTIFIED TELECOMMUNICATIONS INSTALLER
When required by the furniture manufacturer, furniture must be installed by
an authorized dealer and a certified furniture installation crew must be
used on the project. All furniture requiring hardwiring must be completed
by a licensed electrician. Communications installers must be Building
Industry Consulting Services International (BICSI) Registered Cabling
Installers, Technician Level or have a minimum of 3 years experience in the
installation of the specified cables and components. All installers,
furniture, electrical and communications, must be on-site if questions
arise. Submit copies of authorized dealer, furniture installation crew,
licensed electrician and certified telecommunications installer
certifications.
1.7 DELIVERY, STORAGE AND HANDLING
1.7.1 Delivery
Deliver furniture to the jobsite in manufacturer's original packaging or
blanket wrapping. Original packaging must be marked with the manufacturer
name, item identification, and project reference clearly marked.
SECTION 12 50 00.13 10 Page 4
Bldg 615 FSH19B615
1.7.2 Furniture Inspection
Inspect furniture and provide notification of damage within the time frame
required by the shipping company while carrier is still on-site. Complete
claims for concealed damage within the time frame required by the shipping
company and furniture manufacturer. A claim file must be maintained that
documents each claim. Forward copies of claims to the Contracting Officer
on a weekly basis.
1.7.3 Storage
Storage space is not available on-site and furniture must be stored at an
off site location. Provide any storage space required for furniture and
transport stored furniture to the project site for installation. Storage
location must be approved by the Contracting Officer at the time of the
furniture order. If storage is required, furniture must be stored in a dry
location that is adequately ventilated and free from dirt and dust, water,
and other contaminants, in a manner that permits easy access for inspection
and handling, and in an environment in accordance with furniture
manufacturers instructions.
1.7.4 Furniture Staging Area
Coordinate location of the furniture staging area with the Contracting
Officer.
1.8 WARRANTY
Provide manufacturer performance guarantees or warranties for single-shift
service and include parts, labor and transportation as follows, unless
otherwise noted:
a. Systems Furniture - 12 year minimum
b. Desks and Workstations - 12 year minimum
c. Filing and Storage - 12 year minimum
d. Seating
(1) Seating, unless otherwise noted - 10 year minimum
(2) 24/7 Seating (multiple shift use) - 10 year minimum
(3) Seating Mechanisms and Pneumatic Cylinders - 10 year minimum
(4) Lounge Seating - 10 year minimum
(5) Stacking Chairs - 10 year minimum
e. Tables
(1) Unless otherwise noted - 10 year minimum
(2) Table Mechanisms - 5 year minimum
(3) Table Ganging Device - 1 year minimum
f. Miscellaneous
SECTION 12 50 00.13 10 Page 5
Bldg 615 FSH19B615
(1) Fabric - 3 year minimum
(2) LED Task Lighting - 5 year minimum
(3) Task Lighting - 3 year minimum
Provide items not listed with a 1 year minimum. When manufacturers
standard performance guarantees or warranties exceed the minimum
requirements identified, provide the standard performance guarantee or
warranty. Submit manufacturer's warranty information for all furniture
items.
PART 2 PRODUCTS
2.1 PRODUCT SUSTAINABILITY CRITERIA
For products in this section, where applicable and to extent allowed by
performance criteria, provide and document the following:
2.1.1 Energy Efficient Equipment
Coordinate requirement for energy efficient equipment, such as appliances
and lighting, and provide documentation in accordance with Section 01 33 29
SUSTAINABILITY REPORTING paragraph ENERGY EFFICIENT EQUIPMENT.
2.1.2 Reduced VOC's for Furniture
Coordinate requirement for reduced VOC requirements for furniture and
provide documentation in accordance with Section 01 33 29 SUSTAINABILITY
REPORTING paragraph REDUCE VOLATILE ORGANIC COMPOUNDS.
2.1.3 Recycled Content of Furniture
Coordinate requirement for recycled content for furniture and provide
documentation in accordance with Section 01 33 29 SUSTAINABILITY REPORTING
paragraph RECYCLED CONTENT.
2.1.4 Bio-Based Content of Furniture
Coordinate requirement for biobased content for furniture and provide
documentation in accordance with Section 01 33 29 SUSTAINABILITY REPORTING
paragraph BIO-BASED PRODUCTS.
2.2 REFERENCE TO MANUFACTURER NAMES AND COLORS
Where product and color is shown as being specific to one manufacturer in
the FF&E Package Attachment, an equivalent color or product by another
manufacturer may be submitted for approval. Manufacturers, style lines,
model numbers, finish, and fabric information are provided to establish
design intent and are not intended to limit the selection of equal products
and colors from other manufacturers.
2.3 FURNITURE REQUIREMENTS
Use the FF&E Package Attachment in conjunction with the drawings and
specifications for the furniture requirements. Systems furniture is
specified in Section 12 59 00 SYSTEMS FURNITURE. Provide furniture from
manufacturer's standard product as shown in the most current published
SECTION 12 50 00.13 10 Page 6
Bldg 615 FSH19B615
price list or amendment. Furniture provided must be part of current line
as indicated with no intent to discontinue within two years. Provide
furniture that is intended for commercial use not residential. submit
product data for all furniture items, to include catalog cuts, brochures,
product information, and other necessary literature to indicate compliance
with specifications. Provide product data for all items together in a
single submittal. When applicable, include GSA schedule information to
confirm that items are available on GSA schedule. Tag product data sheets
with applicable furniture item code and name. Submit data for all product
style options for selection when options are available. This applies to but
is not limited to furniture items that have options such as edge details,
hardware options, and grommet colors. Submit manufacturer's certification
stating that furniture meets the specifications.
2.3.1 EXISTING FURNITURE (GOVERNMENT FURNISHED/GOVERNMENT INSTALLED-GF/CI)
2.3.1.1 Existing Furniture that is Not Reused
Disassemble and relocate any furniture identified as not to be reused to
the 502d Civil Engineering Squadron Warehouse facility located on JBSA Fort
Sam Houston facility. This includes disconnecting furniture electrical
connections at the building source. Coordinate with electrician for safe
terminations or removal of disconnected building electric system supply
circuits. Protect all items from damage and provide security and weather
protection prior to and during pickup.
2.3.1.2 Existing Furniture Communications
Remove existing Information Technology (IT) cables (i.e. SIPRNET, NIPRNET,
J-WIC'S, etc.) and telephone wiring from existing furniture systems
identified to be reused or requiring excessing.
2.3.2 Construction
a. Provide furniture that complies with the following testing requirements:
(1) ANSI/BIFMA
(a) Office Seating - ANSI/BIFMA X5.1
(b) Vertical Files - ANSI/BIFMA X5.3
(c) Lounge Seating - ANSI/BIFMA X5.4
(d) Desk Products - ANSI/BIFMA X5.5
(e) Panel Systems - ANSI/BIFMA X5.6
(f) Storage - ANSI/BIFMA X5.9
(2) Flammability
(a) Systems furniture and workstation panel components must meet
requirements for flame spread and smoke development as specified
by NFPA 101 except as follows. Conduct testing in accordance with
either ASTM E84 or UL 723 on the entire assembled panel of the
worst case (most combustible) combination of fabric and interior
construction. In addition, fabric must meet the requirements of
NFPA 265. Panel flame spread shall not exceed 75 for Class B ,
SECTION 12 50 00.13 10 Page 7
Bldg 615 FSH19B615
and panel smoke development shall not exceed 450 for Class A, B,
and C.
b. Provide furniture with no rough or sharp edges or exposed connections.
Clips, screws, and other construction elements must be concealed
wherever possible.
c. Items such as desks, workstations and systems furniture must include
all necessary components to be structurally sound and must not be
attached to the wall unless specified to be wall mounted in the
contract documents.
d. Desks, workstations, storage, and tables must have leveling devices to
compensate for uneven floors.
e. The underside of desks, workstations, and tables must be completely and
smoothly finished.
f. The backside of freestanding desks, workstations, and storage must be
finished.
g. Provide chair casters and glides appropriate for the floor material
they are located on, such as carpet and resilient flooring.
2.3.3 Locks and Keying
a. All drawers and doors, including but not limited to overhead storage
cabinets, storage towers, supply cabinets, storage cabinets, desk and
workstation pedestals, and filing cabinets must be lockable.
b. Key each desk and workstation in an office differently and key locks
within each desk and workstation alike.
c. Furniture storage components in private offices must be keyed alike.
Key each private office differently.
d. Provide field changeable lock cylinders in desks and workstations with
a minimum of 100 different key options. Number keys and lock cylinders
for ease of replacement or clearly label locks with a key number,
except for those manufacturers who have removable format locks.
e. Drawers within a pedestal must be lockable either by a central lock
that controls all pedestals under one work surface or an individual
keyed lock in each pedestal.
f. Central file and storage units which are grouped together but are not a
part of a workstation must be keyed alike unless otherwise specified.
g. Provide two keys for each workstation when components are keyed alike.
Also provide two keys for each miscellaneous item such as filing
cabinets, supply cabinets, storage cabinets, and similar type furniture
items.
h. Provide three copies of each master key to the Contracting Officer.
i.Leave keys in locks .
SECTION 12 50 00.13 10 Page 8
Bldg 615 FSH19B615
2.3.4 Receptacle Bodies and Device Cover Plates
Provide furniture panel faceplates and receptacle body types and color as
specified in 12 59 00 SYSTEMS FURNITURE . Provide color as follows:
a. Faceplate: match panel trim color
b. Receptacle Bodies: match panel trim color
c. Communication Cable Jackets: match receptacle device cover plates
in color
d. Isolated Ground Receptacles: orange or be of a different color than
other receptacles
2.3.5 Keyboard Tray
Provide worksurfaces that are capable of accepting an articulating keyboard
tray at locations indicated. The keyboard tray must be capable of fully
recessing under the work surface and extending to give the user full access
to the keyboard. The keyboard tray must have height adjustability and
positive and negative tilting capability and have 180-degree swing side
travel rotation. The keyboard tray must have a wrist support and include a
mouse pad at the same level as the keyboard that can accommodate both right
and left handed users.
2.3.6 Fabric and Finish
Submit samples of all furniture fabric and finishes. Samples must be
actual samples, not photographic representations, size must be a minimum of
3 by 3 inches. If necessary, provide larger size samples to clearly
represent pattern. Label samples with fabric or finish code, furniture
item code and name, manufacturer name, and color information. Fabric
samples must also be labeled with fiber content and double rub testing
information.
2.3.6.1 Fabric
a. Fabric must be from manufacturer's standard line and graded-in textile
manufacturer's fabrics. Do not provide COM fabrics.
b. Provide a mid grade fabric, unless otherwise noted. Example:
manufacturer available grades 1 through 4 (even number of grades),
provide grade 3; manufacturer available grades A through D (even number
of grades), provide grade C; manufacturer available grades A through E
(odd number of grades), provide grade C (middle grade).
c. Provide a topical or inherent soil retardant treatment where indicated.
d. Fabric for seating must comply with a minimum of 55,000 double rubs
unless otherwise noted. Perform double rub testing in accordance with
the ASTM D4157 Wyzenbeek Method.
e. Provide vinyl, polypropylene or similar type fabric for seating only if
allowed in FF&E Package Attachment.
f. Pattern:
(1) Provide patterned upholstery fabric to help hide soiling. Pattern
SECTION 12 50 00.13 10 Page 9
Bldg 615 FSH19B615
is defined as follows:
(a) Solid Color: textured, or pattern smaller in size than the
small size pattern
(b) Small Size Pattern: minimum 1/2 inch
(c) Medium Size Pattern: minimum 2 inch
(d) Large Size Pattern: minimum 5 inch
(2) Provide patterns as specified in the FF&E Package Attachment.
g. See FF&E Package Attachment for additional information.
2.3.6.2 Finishes
Provide furniture finishes as listed below unless otherwise noted:
a. Finishes must be able to be cleaned with ordinary household cleaning
solutions. Wood finishes must be able to be cleaned with damp cloth as
directed by the manufacturer.
b. The finish of steel surfaces must be the manufacturer's most durable
finish such as factory powder coat or baked enamel.
c. Grommet colors must be compatible and coordinated with desk,
workstation, and table finish colors.
e. Plastic laminate worksurfaces and table tops must be neutral in color
and must have a pattern to help hide soiling.
f. See FF&E Package Attachment for additional information.
2.4 FURNITURE LAYOUT
Provide furniture layout as indicated.
PART 3 EXECUTION
3.1 BUILDING EXAMINATION
Become familiar with details of the work, inspect all areas and conditions
under which furniture is to be installed, and coordinate scheduling of
dedicated elevators and docks. Notify the Contracting Officer in writing
of any conditions detrimental to the proper and timely completion of the
installation. Work will proceed only when conditions have been corrected.
3.2 BUILDING PROTECTION
Protect building surfaces to prevent soiling and damage during delivery and
installation. Any soiling and damage that occurs to the building during
the installation of furniture must be cleaned and repaired, or replaced to
its original condition and must be approved by the Contracting Officer.
SECTION 12 50 00.13 10 Page 10
Bldg 615 FSH19B615
3.3 INSTALLATION
3.3.1 Installation Drawings
Installation drawings must include furniture layout, critical dimensions
and locations of electrical and communications. Furniture layouts shall
reflect field verified conditions. Drawings must be at 1/4 inch = 1 foot
scale, unless otherwise specified. Provide typical plans and
isometrics/elevations of desks and workstations at a scale of 1/2 inch = 1
foot. When applicable, provide desk and workstation electrical and
communications locations. When applicable include controlled-circuit
identification for each furniture receptacle and coordinate with the
building electrical system circuits in accordance with ASHRAE 90.1 - IP.
Critical dimensions include, but are not limited to clearances and aisle
widths. Drawings must include layout for furniture systems workstations
for coordination purposes. Label furniture with furniture item code
identified in this specification. Submit grommet, power and communication
units, and wire management locations.
3.3.2 Furniture Installation Procedures
Complete installation in accordance with manufacturer's installation
instructions, assembly manuals, warranty requirements and approved
installation drawings. Also comply with the following requirements:
a. Use material handling equipment with rubber wheels.
b. Furniture and components must be installed level, plumb, square, and
with proper alignment with adjoining furniture.
c. Match keys to locks and check locking mechanisms.
d. Check drawers, doors, lighting, and other operable items and mechanisms
for proper operation.
e. Remove all protective wrapping tape, residue, and related type items.
f. Securely interconnect furniture components where required.
g. Securely attach and anchor furniture components to the building when
required.
h. Securely anchor furniture such as shelving and storage units to the
building when required by the manufacturer.
i. All items with an electrical plug, such as but not limited to task
lighting and tables with electrical power, must be fully operational.
j. All hardwired furniture, such as but not limited to furniture systems,
must be fully operational. Verify that voltage is present in electrical
outlets. Verify controlled-circuit outlets are properly configured in
accordance with the installation drawings.
k. Furniture must not block SIPRNET jacks or the jack enclosures on
walls. Report conflicts to Contracting Officer to discuss resolution.
l. Upon completion of installation, all furniture must be completely
cleaned, finished, leveled, aligned, operational and functional.
SECTION 12 50 00.13 10 Page 11
Bldg 615 FSH19B615
3.3.3 Furniture Communications Installation
Provide all Information/Technology (IT) cables (i.e. SIPRNET, NIPRNET,
J-WIC'S, etc.) and phone wiring up to and including the face plate/box of
all furniture as required and the services to install the cables, wiring
and face plates/boxes in the furniture. Coordinate cable type, cable
jacket and outlet jack color with Section 27 10 00 BUILDING
TELECOMMUNICATIONS CABLING SYSTEM. Furniture communication installers must
be on site to install communication cables, wiring and other components for
furniture during furniture installation. Coordinate the TIA-568-C.2
pin/pair assignments for communication outlets to match the configuration
of the building's non-furniture outlets; coordinate with Contracting
Officer. All items with a communication interface must be fully
operational.
3.4 CLEANING
Remove all packing materials and other trash from the jobsite. Upon
completion of installation, all products must be clean, including inside
all drawers and doors, and the area must be free of debris and left in a
clean and neat condition. Any defects in or damage to furniture must be
repaired or replaced and approved by the Contracting Officer. Damaged
products that cannot be satisfactorily repaired must be replaced. Correct
any problems with assembly and installation. Prior to any furniture
repair, replacement, and/or assembly and installation corrections, protect
the building surfaces.
3.5 OPERATION AND MAINTENANCE MANUALS
Submit the Furniture, Data Package 1 in accordance with Section 01 78 23
OPERATION AND MAINTENANCE DATA and include the following:
3.5.1 Assembly Manuals
Describe assembly and re-configuration procedures. Provide three sets of
installation video tapes if available.
3.5.2 Installation Instructions
Provide a copy of the instructions used to install the furniture. Also
describe any special procedures or helpful hints learned during the
installation process.
3.5.3 Maintenance Manuals
Describe proper cleaning and minor repair procedures, include cleaning
instructions for fabrics.
3.5.4 Electrical System Manuals
Describe the functions, configuration, and maintenance of the furniture
electrical system (power, communication, and data). This information may
be included in the assembly or maintenance manuals.
3.5.5 Special Tools
Provide three sets of special tools necessary for assembly and disassembly
of furniture and components from each manufacturer. Mark tool(s) with
manufacturer and product information.
SECTION 12 50 00.13 10 Page 12
Bldg 615 FSH19B615
3.5.6 Furniture Drawings
Provide hard copy and electronic, showing installed furniture layout.
Include all modifications. Provide electronic copies on a CD-ROM.
Coordinate type (such as but not limited to Microstation, AutoCad and
Revit) and version required with User. Include critical dimensions, and
locations of building and furniture electrical and communications. Provide
drawings at 1/4 inch = 1 foot scale, unless otherwise specified. Provide
typical plans and isometrics/elevations of workstations at a scale of 1/2
inch = 1 foot. Code all furniture with furniture item code identified in
this specification.
3.5.7 Furniture Listing
Provide complete listing, hard copy and electronic, of furniture provided.
Include all modifications. Provide electronic copies on a CD-ROM.
Coordinate type of electronic file required with User (such as but not
limited to Word and Excel). Listing must include furniture item code and
name used in FF&E Package, part/model numbers, fabrics and finishes for all
components furnished. Organize listing by item name and code and provide
building totals.
3.5.8 Order Form Documentation
Provide Order Form Documentation with Purchase Order number and project
name and location to allow the User to follow up on warranty issues and
help with future purchases.
3.5.9 Key Control System
Key Control System. Provide system in excel format; indicate lock number,
room number and location of lock within rooms if more than one lock number.
-- End of Section --
SECTION 12 50 00.13 10 Page 13
Bldg 615 FSH19B615
SECTION 12 59 00
SYSTEMS FURNITURE
PART 1 GENERAL
1.1 REFERENCES
The publications listed below form a part of this specification to the
extent referenced. The publications are referred to within the text by the
basic designation only.
AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI)
ANSI Z97.1 (2015) Safety Glazing Materials Used in
Buildings - Safety Performance
Specifications and Methods of Test
AMERICAN SOCIETY OF HEATING, REFRIGERATING AND AIR-CONDITIONING
ENGINEERS (ASHRAE)
ASHRAE 90.1 - IP (2016; ERTA 1-8 2017; INT 1-5 2017) Energy
Standard for Buildings Except Low-Rise
Residential Buildings
ASTM INTERNATIONAL (ASTM)
ASTM C1048 (2012; E 2012) Standard Specification for
Heat-Strengthened and Fully Tempered Flat
Glass
ASTM C423 (2009a) Sound Absorption and Sound
Absorption Coefficients by the
Reverberation Room Method
ASTM E290 (2014) Bend Testing of Material for
Ductility
ASTM E84 (2017) Standard Test Method for Surface
Burning Characteristics of Building
Materials
BIFMA INTERNATIONAL (BIFMA)
ANSI/BIFMA M7.1 (2011; R 2016) Test Method for Determining
VOC Emissions from Office Furniture
Systems, Components and Seating
ANSI/BIFMA X5.5 (2014) American National Standards For
Office Furnishings -Desk Products
ANSI/BIFMA X5.6 (2016) American National Standards For
Office Furnishings -Panel Systems
SECTION 12 59 00 Page 1
Bldg 615 FSH19B615
NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION (NEMA)
NEMA WD 1 (1999; R 2015) Standard for General Color
Requirements for Wiring Devices
NEMA WD 6 (2016) Wiring Devices Dimensions
Specifications
NATIONAL FIRE PROTECTION ASSOCIATION (NFPA)
NFPA 101 (2018; TIA 18-1) Life Safety Code
NFPA 265 (2015) Standard Methods of Fire Tests for
Evaluating Room Fire Growth Contribution
of Textile Coverings on Full Height Panels
and Walls
NFPA 70 (2017; ERTA 1-2 2017; TIA 17-1; TIA 17-2;
TIA 17-3; TIA 17-4; TIA 17-5; TIA 17-6;
TIA 17-7; TIA 17-8; TIA 17-9; TIA 17-10;
TIA 17-11; TIA 17-12; TIA 17-13; TIA
17-14) National Electrical Code
SCIENTIFIC CERTIFICATION SYSTEMS (SCS)
SCS SCS Global Services (SCS)Indoor Advantage
TELECOMMUNICATIONS INDUSTRY ASSOCIATION (TIA)
TIA-568-C.2 (2009; Errata 2010; Add 2 2014; Add 1
2016) Balanced Twisted-Pair
Telecommunications Cabling and Components
Standards
TIA-569 (2015d) Commercial Building Standard for
Telecommunications Pathways and Spaces
U.S. NATIONAL ARCHIVES AND RECORDS ADMINISTRATION (NARA)
36 CFR 1191 Americans with Disabilities Act (ADA)
Accessibility Guidelines for Buildings and
Facilities; Architectural Barriers Act
(ABA) Accessibility Guidelines
UNIFIED FACILITIES CRITERIA (UFC)
UFC 3-520-01 (2015)Interior Electrical Systems.
UNDERWRITERS LABORATORIES (UL)
UL 1286 (2008; Reprint Feb 2015) Office Furnishings
UL 2818 (2013) GREENGUARD Certification Program
For Chemical Emissions For Building
Materials, Finishes And Furnishings
UL 723 (2008; Reprint Aug 2013) Test for Surface
Burning Characteristics of Building
Materials
SECTION 12 59 00 Page 2
Bldg 615 FSH19B615
1.2 SUBMITTALS
Government approval is required for submittals with a "G" designation;
submittals not having a "G" designation are for Contractor Quality Control
approval. Submittals with an "S" are for inclusion in the Sustainability
eNotebook, in conformance to Section 01 33 29 SUSTAINABILITY REPORTING.
Submit the following in accordance with Section 01 33 00 SUBMITTAL
PROCEDURES:
SD-02 Shop Drawings
Detail Drawings; G
SD-03 Product Data
Warranty; G
Workstations
Power and Communications
Communications
SD-04 Samples
Workstations; G
Mock-up; G
Samples
SD-06 Test Reports
Selected Components; G
Panel Acoustics; G
Fire Safety; G
Electrical System; G
SD-07 Certificates
Workstations
Indoor Air Quality
SD-08 Manufacturer's Instructions
SD-10 Operation and Maintenance Data
Assembly Manuals; G
Maintenance Manuals; G
Cleaning; G
Electrical System; G
SECTION 12 59 00 Page 3
Bldg 615 FSH19B615
Maintenance Agreements
Installation; G
SD-11 Closeout Submittals
Energy Efficient Equipment; S
Reduced VOC's for Furniture; S
Recycled Content of Furniture; S
Bio-Based Content of Furniture; S
Indoor Air Quality for Office Furniture Systems and Seating; S
Recycled Content for system furniture components; S
1.3 CERTIFICATIONS
1.3.1 Indoor Air Quality Certifications
1.3.1.1 Office Furniture Systems and Seating
Provide products certified to meet indoor air quality requirements by
UL 2818 (Greenguard) Gold, SCS Global Services Indoor Advantage Gold,
ANSI/BIFMA M7.1 Certification or provide certification or validation by
other third-party program that products meet the requirements of this
Section. Provide current product certification documentation from
certification body.
1.4 QUALITY ASSURANCE
1.4.1 General Safety
Provide workstation products free of rough or sharp edges. Provide panel
supported components with a positive, integral locking device which secures
components without the use of additional screws or clamps to prevent the
components from being accidentally pulled or knocked off the panels.
1.4.2 Fire Safety
Components must meet requirements for flame spread and smoke development as
specified by NFPA 101 except as follows. Conduct testing in accordance
with either ASTM E84 or UL 723 on the entire assembled panel of the worst
case (most combustible) combination of fabric and interior construction.
In addition, fabric must meet the requirements of NFPA 265. Do not exceed
25 for Class A for panel flame spread and 450 for Class A, B and C panel
smoke development.
1.4.3 Electrical System
Task lights are required to be UL listed and installation of task lighting
must meet the requirements of NFPA 70. The electrical system must meet the
requirements of UL 1286. Submit three sets of electrical system manuals
describing the functions, configuration, and maintenance of the electrical
system (power , communications , data). This material may be included in
the Assembly or Maintenance manuals at the Contractor's option.
SECTION 12 59 00 Page 4
Bldg 615 FSH19B615
1.4.4 Detail Drawings
Submit detail drawings showing communications, electronic data processing
(EDP) and local area network (LAN); locations may be provided as a separate
submittal from remaining workstation drawings. Provide drawing
requirements, which are the furniture manufacturer's responsibility, as a
single submittal. Provide electronic drawings to the user for future
re-configuration in the software package requested by the user. Include in
the electronic drawings all modifications made during installation. As a
minimum, submit the following:
a. Overall reference drawings: Drawings showing workstation locations and
overall plan view within each floor in a scale of 1/8 inch = 1 foot.
Layouts must reflect field verified conditions and clearly illustrate
the overall space planning concept and intent.
b. Installation drawings: Drawings showing workstations, panels,
components, and plan view within each floor. Identify workstations by
workstation type; submit drawings showing the proposed workstation
installation at a scale of 1/4 inch = 1 foot, unless otherwise
specified. Installation drawings must reflect field verified
conditions.
c. Workstation elevations: Dimensioned workstation elevations showing
each type of workstation with panel frame configurations and all
components identified with manufacturer's catalog numbers. Draw
elevations at 1/2 inch = 1 foot scale.
d. Panel drawings: Panel drawings showing locations and critical
dimensions from finished face of walls, columns, panels, including
clearances and aisle widths. Key assemblies to a legend which includes
width, height, configuration and composition of frame covers finishes
and fabrics (if different selections exist within a project), power or
nonpower, connectors and wall mount hardware. Coordinate panel
placement with location of electrical, voice/date LAN, SIPRNet,
NIPERNet, mechanical and fire protection fixtures. Drawings must
reflect field verified conditions.
e. Electrical drawings: Drawings showing power provisions including type
and location of feeder components (service entry poles, base or ceiling
feeds), activated power receptacles and other electrical components.
Wiring configuration (circuiting, switching, internal and external
connections) identified and a legend provided as applicable. Identify
which receptacles in typical furniture configurations will be connected
to controlled building power circuits as applicable to meet
ASHRAE 90.1 - IP requirements. Coordinate with electrical drawings.
f. Wire management capacity drawings.
g. Communication drawings showing telephone provisions: Drawings
indicating the type and location of feeder components and
communications jacks with wiring configuration identified where
applicable.
h. Communication drawings showing electronic data processing provisions:
Drawings indicating the type and location of feeder components,
communications jacks, or accessories with wiring configuration
identified where applicable.
SECTION 12 59 00 Page 5
Bldg 615 FSH19B615
i. Communication drawings showing local area network provisions: Drawings
indicating the type and location of feeder components and data jacks
with extra ports for future expansion with wiring configuration
identified where applicable.
j. Communications drawings indicating the TIA-568-C.2 pin/pair assignment
that will be used for communications outlet as coordinated with the COR.
k. Reflected ceiling plan for projects specified with power poles.
l. Drawings indicating cabling is protected at all transition points, and
that metallic separation is provided between telecommunication and
power wiring in the utility columns and systems furniture track in
accordance with TIA-569 and NFPA 70.
1.5 DELIVERY, STORAGE, AND HANDLING
Deliver components to the jobsite in the manufacturer's original packaging
with the brand, item identification, and project reference clearly marked.
Remove furniture from packaging and store in an unoccupied, dry location
that is ventilated. Storage shall be free from dirt and dust, water, and
other contaminants, and in a manner that permits easy access for inspection
and handling.
1.6 WARRANTY
Warrant the systems furniture for a minimum period of 12 years with the
following exceptions: fabrics and other covering materials, and paper
handling products for 3 years, LED drivers/power supplies for 5 years, and
electromagnetic ballasts for 3 years. Warranties must be signed by the
authorized representative of the manufacturer. Present warranties,
accompanied by document authenticating the signer as an authorized
representative of the guarantor, to the Contracting Officer upon the
completion of the project. Guarantee that the workstation products and
installation are free from any defects in material and workmanship from the
date of delivery. Submit two copies of the warranty.
1.7 MAINTENANCE AGREEMENTS
Collect information from the manufacturer about take back program options,
and submit to Contracting Officer. Submit documentation that includes
contact information, summary of procedures, and the limitations and
conditions applicable to the project. Indicate manufacturer's commitment
to reclaim materials for recycling and/or reuse and avoid landfilling and
burning reclaimed materials. When such a service is not available through
a manufacturer, local recyclers should be sought after to reclaim the
materials.
PART 2 PRODUCTS
2.1 MATERIALS
Provide System Furniture Components with a minimum of 55 percent recycled
content. Provide data identifying percentage of recycled content for
system furniture components.
Provide certification of indoor air quality for Office Furniture Systems
and Seating.
SECTION 12 59 00 Page 6
Bldg 615 FSH19B615
2.2 PRODUCT SUSTAINABILITY CRITERIA
For products in this section, where applicable and to extent allowed by
performance criteria, provide and document the following:
2.2.1 Energy Efficient Equipment
Coordinate requirement for energy efficient equipment, such as lighting,
and provide documentation in accordance with Section 01 33 29
SUSTAINABILITY REPORTING paragraph ENERGY EFFICIENT EQUIPMENT.
2.2.2 Reduced VOC's for Furniture
Coordinate requirement for reduced VOC requirements for furniture and
provide documentation in accordance with Section 01 33 29 SUSTAINABILITY
REPORTING paragraph REDUCE VOLATILE ORGANIC COMPOUNDS.
2.2.3 Recycled Content of Furniture
Coordinate requirement for recycled content for furniture and provide
documentation in accordance with Section 01 33 29 SUSTAINABILITY REPORTING
paragraph RECYCLED CONTENT.
2.1.4 Bio-Based Content of Furniture
Coordinate requirement for biobased content for furniture and provide
documentation in accordance with Section 01 33 29 SUSTAINABILITY REPORTING
paragraph BIO-BASED PRODUCTS.
2.3 SYSTEM DESCRIPTION
2.3.1 Workstations
This specification establishes the minimum requirements for the acquisition
and installation of a complete and usable system of workstations composed
of panels, freestanding work surfaces or base units, supporting components,
electrical hardware, communications, special electrical features, and
accessories. Provide workstation requirements and configurations in
accordance with the furniture layout and typical workstation types shown in
drawings and specified herein. Provide components and hardware from a
single manufacturer that are standard products as shown in the most recent
published price lists or amendments. Proposed product must be part of the
manufacturer's current line with no intent to discontinue within two
years. Submit complete listing of part/model numbers for all components to
be provided, including names and codes of components referenced on updated
drawings. Provide electrical components from a single manufacturer to the
extent practicable (different types of components may be of different
manufacturers, but all units of a given component must be from a single
source). Conformance with NFPA 70, UL 1286, NFPA 101, and 36 CFR 1191 is
required. Coordinate the work of this section with that to be performed
under other sections. This specification may include items which are not
manufactured by the furniture manufacturer; provide any such items under
this section. Submit two complete sets of certificates attesting that the
proposed workstation meets specified requirements. Date the certificate
after the award of the contract, include the name of the project, and list
specific requirements being certified.
SECTION 12 59 00 Page 7
Bldg 615 FSH19B615
2.3.2 Samples
Submit samples as required to obtain final approval. The Government
reserves the right to reject any finish samples that do not satisfy the
technical or color requirements. Work can not proceed without sample
approval in writing from the Contracting Officer. Submit four sets of the
finish samples listed below:
a. Panel, tackboard and overhead door fabric. Minimum 6 by 6 inches with
label designating the manufacturer, pattern, color, fiber content,
fabric width, fabric weight, fire rating, and use (panel and/or
tackboard).
b. Workstation component finishes. Minimum 2-1/2 by 3 inches with label
designating the manufacturer, material composition, thickness, color,
and finish.
c. Personal Task lights (Not overhead task lights).
d. Panel glazing. Glazing samples with label designating the material and
safety ratings.
2.3.3 Mock-up
Submit a Mock-up of an actual workstation reflecting approved finishes and
fabrics. Locate the mock-up installation at the local dealership. Do not
order product for the project until the mock-up has been approved. Submit
manufacturer's product and construction specifications which provide
technical data for furniture system and components specified, including
task lighting and illumination performance information. Include adequate
information in the literature to verify that the proposed product meets the
specification. Review of the mock-up may result in adjustments to the
product, layout and finishes. The approved mock-up can be used in
installation.
2.3.4 Alternate Design
Manufacturers who are unable to provide workstations that conform exactly
to the furniture layouts and typical workstation types shown in the
contract drawings, may submit alternate designs for consideration by the
Contracting Officer. Alternate designs must meet or exceed the following
criteria. Alternate designs that are submitted but do not meet these
criteria will be rejected. In the alternate design provide workstations
and components of the same basic size and configuration shown, with only
the sizes of the individual components within the workstation changed to
meet the standard product of the manufacturer or site conditions.
2.3.4.1 Component Requirements
Provide the types of components or elements as shown on the drawings and as
specified in PART 2 PRODUCTS of this specification. Do not reduce the
storage capacity, number of workstations accommodated, width of aisles, or
workstation configuration.
2.3.4.2 Wiring Configuration
Alternate configurations shall support the circuiting and connection
capabilities identified under the provisions pertaining to power
SECTION 12 59 00 Page 8
Bldg 615 FSH19B615
distribution of paragraph POWER AND COMMUNICATIONS. Generally any
alternate will be acceptable which involves only a variation in size or
quantity that exceeds the specified configuration.
2.3.5 Performance Requirements
Panels, frames and frame covers, connection system, work surfaces,
pedestals, shelf units, overhead door cabinets, lateral files, locks,
accessories, and miscellaneous hardware must meet testing as specified.
ISO 9001 certified manufacturers may perform in-house testing.
Manufacturers not ISO 9001 qualified will be required to produce testing by
an independent testing laboratory. Component specific requirements are
listed in appropriate paragraphs.
2.3.5.1 Selected Components
Workstation conformance to ANSI/BIFMA X5.5 and ANSI/BIFMA X5.6 is required
with the following exceptions: Panels, or panel supported components
conformance to ANSI/BIFMA X5.6 is required. Representative items will be
selected for testing based on worst case situations (i.e., the deepest and
widest work surface or shelf). Perform the keyboard drawer or shelf test
applying a 50 lb load to the center of the keyboard shelf for a period of 5
minutes. Any loosening of attachments or damage to the operation of the
drawer or shelf will be cause for rejection.
2.3.5.2 Panel Acoustics
Provide acoustical panels with a minimum noise reduction coefficient (NRC)
of 0.65 when tested in accordance with ASTM C423 and a minimum sound
transfer coefficient (STC) of 20 when tested in accordance with ASTM E290.
Conduct the test on the entire assembled panel, full face area (the
complete core, adhesive, decorative fabric, frame and joining components).
2.3.5.3 Panel Glazing
Tempered glass must conform to ANSI Z97.1 and ASTM C1048, Kind FT,
Condition A, Type I, Class 1 Transparent .
2.3.6 Pattern and Color
Provide pattern and color of finishes and fabrics for panel systems,
components, and trim as shown on the drawings .
2.4 SYSTEMS FURNITURE
2.4.1 Panel System Components
Supply aaccessories and appurtenances for a completely finished panel
assembly with the system. Provide a system capable of structurally
supporting cantilevered work surfaces, shelves, files, overhead cabinets,
and other components in the configurations shown on the drawings plus more
than one fully loaded component per panel per side. Provide panels that
aretackableorcapable of accommodating fabric covered tackboards, .
Segments will be field removable from both sides of the panel. Provide a
spine wall system where electrical and data management will be easily
accessible by removable wall covers that can be removed while workstation
components are still attached. Cables must be laid in the system, not
threaded through the frame. Provide a panel system that is available in a
variety of nominal widths and heights as designated on the drawings.
SECTION 12 59 00 Page 9
Bldg 615 FSH19B615
Measure heights from the finished floor to the top of the panel. Supply
powered and nonpowered panels that are compatible in height. Coordinate
panel heights with the HVAC and electrical designs. Minimum panel
thickness is 3 inches thick. System to have 100 percent off-modular
capability with no defacement of any element caused by components when used
in an off-modular application. Unique panel frames must not be required
for off modular connections. Submit three sets of Assembly Manuals
describing assembly and reconfiguration procedures.
2.4.2 Panel Finishes
Provide panels in the following options: tackable fabric,marker
surface,paint,. Frame covers may have different options on either side of
the frame. Exposed panel trim to have a factory baked enamel or epoxy
powder finish. Filler trim will either match the panel trim or be fabric
covered to match the panel fabric. Provide each fabric-faced panel with a
seamless width of fabric stretched over the entire face of the panel. The
fabric color throughout the installation must be consistent. Curved panels
may use adhesives on curved sections. Attach the fabric securely and
continuously along the entire perimeter of the panel and allow for easy
removal and replacement in the field (with the exception of curved
panels). .2.4.3 Raceways
Provide raceways and covers as an integral part of the panel whether
powered or nonpowered. Magnet held base covers will not be accepted.
2.4.4 Leveling Glides
Provide precise alignment of adjacent panels and include leveling glides to
compensate for uneven floors. Provide quantity and location of leveling
glides as recommended by the manufacturer. A minimum 3/4 inch adjustment
range is required.
2.4.5 Connection System
Provide connectors which accommodate a variety of configurations as
indicated on the drawings to include: a straight line connection of 2
panels (180 degrees), corner connection of 2 panels (90 degrees), T
connection of 3 panels (90 degrees), cross connection of 4 panels (all 90
degrees), angle connection of 2 panels (120 degrees),. Provide tight
connections with continuous visual and acoustical seals. Plastic, painted
metal, fabric or wood finish connections are required to match system.
Provide connector system that allows removal of a single panel within a
typical workstation configuration, without requiring disassembly of the
workstation or removal of adjacent panels. Provide for connection of
similar or dissimilar heights to include trim pieces to finish the exposed
edge. Right angle (90 degree) connections between panels must not
interfere with the capability to hang work surfaces and other components on
any adjacent panel. Provide, as required, the continuation of electrical
and communications wiring within workstations and from workstation to
workstation. Filler posts must be level with the top rail.
2.4.6 Wall Mounted Panels
Use wall-mount components when it is necessary to attach panels or vertical
panel-frame assemblies to the building walls. Provide structural support
for wall panels as required. Panels and other systems furniture components
are not be wall mounted unless they are included in the original design.
SECTION 12 59 00 Page 10
Bldg 615 FSH19B615
2.4.7 Glazed Panel Inserts
Provide safety glass glazed panel inserts in accordance with ANSI Z97.1 and
ASTM C1048. Acrylic glazing will not be accepted.
2.4.8 Door Panels
Provide door panels with a rigid metal frame with rails, a threshold, and a
wood clad door adaptable to either hand swing. Allow for a minimum 32 inch
clear opening. Include connectors, hinges, and brushed chrome finished ADA
compliant door knob or handle.
2.4.9 Sliding Doors
Attach sliding or rolling doors to the panel as shown on the drawings.
Provide doors that the direction in which the door slides can be changed in
the field. Supply door in same width or wider than the opening to be
covered. Provide door pulls for each side of door. Door frame to match
the panel frame color.
2.5 DESK-BASED SYSTEM
Supply accessories and appurtenances for a completely finished desk-based
assembly within the system. Provide a desk-based system that is
free-standing, independent of panel system support and capable of
structurally supporting work surfaces, shelves, and other components in the
configurations shown on the drawings. Provide a variety of nominal widths
and depths as indicated on drawings.
2.6 WORK SURFACES
2.6.1 Construction
Construct work surfaces to prevent warpage. Fully support work surfaces
from the panels or support jointly by the panels and supplemental legs,
pedestals, or furniture end panels. Use supplemental end supports only
under work surfaces when the work station configuration does not permit
full support by the panels. Use metal support brackets to support work
surfaces from the panels, provide metal-to-metal fitting to the vertical
uprights of the panels, vertically adjustable, to lock the work surfaces in
place without panel modifications. Abutting work surfaces must line up
closely and be at equal heights when used in side-by-side configurations in
order to provide a continuous and level work surface. Provide pre-drilled
holes to accommodate storage components, pedestals and additional supports
in work surfaces, or drill holes at the job site to accommodate these
items. Provide work surfaces in sizes and configurations shown on the
drawings. Provide height adjustable
work surfaces from 25 to 52 inches above the finished floor with a
electrical control. Provide corner, peninsula, and counter/transaction
work surfaces as shown on the drawings and include hardware necessary to
provide firm and rigid support.
2.6.2 Finishes
Provide work surfaces with a finished top surface of high pressure plastic
laminate, and a smoothly finished underside. The work surface must not be
damaged by ordinary household solvents, acids, alcohols, or salt
solutions. Provide metal support brackets that match the color and finish
of trim. Provide PVC edges
SECTION 12 59 00 Page 11
Bldg 615 FSH19B615
2.7 PEDESTALS
Provide drawer configurations and pedestal height as shown on the
drawings. Provide the deepest possible pedestal for each work surface size
specified. Free standing mobile pedestals to include an attached
upholstered seat cushion, a handle for moving, and casters. Mobile
pedestals must be load bearing and equipped with counterbalance as
standard. Provide appropriate height of mobile pedestal so it can be
stored under a standard height worksurface.
2.7.1 Construction
Provide pedestals and drawers of steel construction with the exception of
drawer fronts. Securely attach drawer faces to the drawer front.
2.7.2 Finishes
Provide a factory baked enamel finish or powder coated for steel surfaces.
Provide plastic laminate drawer fronts.
2.7.3 Drawer Requirements
Pedestals must be field interchangeable from left to right, and right to
left, and must retain the pedestal locking system capability. Design
pedestals to protect wires from being damaged by drawer operation. Provide
pedestals that are support work surfaces. Drawers must stay securely
closed when in the closed position and provide each drawer with a safety
catch to prevent accidental removal when fully open. File drawers to be
provided with full extension ball bearing drawer slides or rack and pinion
suspension. File drawers to be provided with hanging folder frames or
rails and capable of hanging side-to-side or front-to-back. Provide
dividers with vertical files.
Provide box drawers with pencil trays. Provide center pencil drawer and
mount under the work surface.
2.8 STORAGE
Provide storage units in the sizes and configurations shown on the
drawings. Depth to accommodate a standard three ring binder
2.8.1 Shelf Unit Construction
Provide metal construction shelf pan with formed edges. Provide shelf
supporting end panels of metal, high density particle board, molded
phenolic resin, or molded melamine. Provide relocatable shelf dividers
with shelf units.
2.8.2 Overhead Cabinet Construction
Provide laminate construction overhead cabinets. Provide doors with a
suspension system. Provide sliding doors on overheads. Overhead cabinet
must be ADA accessible.
2.8.3 Lateral File, Vertical File and Book Case Construction
Provide units and file fronts, top and end panels of steel construction.
File drawers to be provided with full extension ball bearing drawer slides
or rack and pinion suspension. File drawers to be provided with hanging
SECTION 12 59 00 Page 12
Bldg 615 FSH19B615
folder frames or rails and capable of hanging side-to-side or
front-to-back.
2.8.4 Finish
Provide a factory baked enamel or epoxy powder coat finish for shelves,
dividers and top dust cover. Provide either a factory baked enamel, epoxy
powder coat or laminate finish for shelf supporting end panels. Shelf
bottom is required to match end panel color. Provide metal doors with an
exterior finish of factory baked enamel and an interior finish of factory
baked enamel or epoxy powder coat. Provide a factory baked enamel finish
or epoxy powder coat on metal drawers.
2.9 ACCESSORIES
2.9.1 Coat Hook
Provide one mounted coat hook per workstation.
2.9.2 Keyboard Tray
Provide work surfaces that are capable of accepting an articulating
keyboard in locations as shown on the drawings. The keyboard tray must be
capable of fully recessing under the work surface and extending to give the
user full access to the keyboard. Provide height adjustability, 180-degree
swing side travel rotation and negative tilting capability. Include a
wrist support and a mouse pad at the same level as the keyboard tray to
accommodate either right or left-handed users.
2.9.3 Tackboards
Fabric must be factory installed. Provide fabric content of tackboards.
Location and size as shown on the drawings.
2.9.4 Erasable Marker Boards
Provide marker boards with a white writing surface that can be easily
written on and erased and unaffected by common marker board
cleaning/conditioning agents. Include a storage tray and minimum two
markers with the markerboard. Size and location as shown on the drawings.
2.9.5 Wall Mounted Components
Provide wall tracks when components are shown attached directly to wall
surfaces. Provide tracks of heavy duty extruded metal with finish and
color matching the the panel trim. Provide vertically aligned tracks
slotted on 1 inch centers in heights required that match slot spacing for
components.
2.9.6 CPU Holder
Provide a mounting to support the computer hard drive. Desk top and floor
locations are not acceptable.
2.9.7 Signage
Provide panel mounted signage composed, at a minimum, of aluminum frame,
back panel, clear plastic cover, and hanging device. Provide signage
approximately 3 by 8 inches and capable of receiving a replaceable standard
SECTION 12 59 00 Page 13
Bldg 615 FSH19B615
white paper insert. Match text type. Provide software for creating text in
PC computers for owner production of replacement paper inserts after
project completion.
2.9.8 Monitor Arm
Provide monitor arm that allows 360 degree monitor rotation for portrait
and landscape viewing, and 60 degree range of lateral and vertical monitor
tilt for additional viewing adjustability. Provide monitor arm that
supports monitors weighing 7 to 19 lbs. Provide dual monitor arm for 2
screens . Mount monitor arm on work surface.
2.10 MISCELLANEOUS HARDWARE
Provide brackets, supports, hangers, clips, panel supported legs,
connectors, adjustable feet, cover plates, stabilizers, and other
miscellaneous hardware that contribute to a complete and operable furniture
system.
2.11 LOCKS AND KEYING
Provide overhead cabinets, vertical files, personal storage towers,
pedestals and lateral files with keyed locks, unless otherwise noted.
Provide field changeable lock cylinders with a minimum of 100 different key
options. Key each workstation individually, and key locks alike within a
workstation. Provide lockable drawers within a pedestal either by a
central lock that controls all pedestals under one work surface or an
individual keyed lock in each pedestal. Key alike
central file and storage units which are grouped together but are not a
part of a workstation unless otherwise specified. Provide two keys for
each lock or two keys per workstation when keyed alike, and provide three
master keys per area as indicated. Number keys and lock cylinders for ease
of replacement. Clearly label locks with a key number, except for those
manufacturers who have removable format locks. Provide door panels
withkeyed door knob set.
2.12 POWER AND COMMUNICATIONS
Provide both powered and nonpowered panels with base raceways capable of
distributing power circuits, communication cables and data lines. Provide
nonpowered bases that are capable of easy field conversion to powered base
without requiring the panel to be dismantled or removed from the
workstation. Provide panels able to support lay-in cabling and having a
large capacity for power and data. Provide ample space for storing excess
wires and fiber optic cables in the interior of the spine wall frame.
Provide easy access to power and data systems in the spine wall without
having to move return panels or components. Provide the ability for the
spine wall system to supply power to a wall-attached panel system and/or an
adjacent desk system. A termination center or utility closet may be
utilized in the wall or at the end of a panel run. Provide copper wiring
harnesses for the system and meet the requirements of UL 1286, UFC 3-520-01,
and NFPA 70, Article 605. Provide conductors with 20 amp 90 degree C, #12
AWG wires (unless indicated otherwise) or the equivalent in the bus
configuration. A single circuit must not serve more than four (4) cubicles
or workstations under any circumstances. The label or listing of
Underwriter's Laboratories, Inc. will be accepted as evidence that the
material or equipment conforms to the applicable standards of that agency.
In lieu of this label or listing, submit a statement from a nationally
recognized, adequately equipped testing agency indicating that the items
have been tested in accordance with required procedures of UL and that the
SECTION 12 59 00 Page 14
Bldg 615 FSH19B615
materials and equipment comply with contract requirements. Electrical work
not addressed in this section must conform to the requirements of Section
26 20 00 INTERIOR DISTRIBUTION SYSTEM.
2.12.1 Panel Raceways
Provide panels that have hinged or removable covers that permit easy access
to the raceway when required but are securely mounted and cannot be
accidentally dislodged under normal conditions. Place raceways in
locations such as the base, beltline, and below and above the beltline.
The raceway must not extend past either panel face by more than 1/2 inch.
Provide metal or plastic covers which attach securely to the raceway as
required and match the finish and color of the panel trim. Provide a
minimum of 2 knockouts (doors) per side for power receptacles and
communications jacks as indicated in raceways on panel frames. Provide
other raceways that are flush with frame covers.
2.12.2 Power Distribution
Provide power distribution as indicated on the drawings. Provide an
internal power and communications raceway and the capability of
disconnecting and connecting external circuits to the electrified raceway
in the panel. Capacity for at least twenty 4-pair category 6 cables is
required for the communications receiving raceway. Power and
communications wiring may share a common wireway if a metal divider is
included to ensure electrical isolation. Provide doors or access openings
for entry of communications cable. Provide the electrified power raceway
for the 8-wire configuration indicated. Unless otherwise indicated,
allocate conductors of the 8-wire system as follows (4-2-2 shared neutrals,
2+2): the three-phase system will have one equipment ground, one isolated
ground, two oversized (133 percent minimum) neutral, and four phase
conductors; each neutral will be used by two phase conductors, no neutral
conductor will be connected to multiple phase conductors of the same phase,
and no ground conductor will be on the same circuit as two phase conductors
from the same phase; circuits sharing a given neutral conductor will share
the same ground conductor.
2.12.2.1 Receptacles
Provide power receptacles in the powered panels. Place devices at the
locations indicated on the plans connected to the designated circuits.
Electrical power receptacles and communications jacks should have the
ability to be hung at multiple vertical increments throughout the frame via
power harnesses. Unless otherwise indicated, receptacles must be 20 amp
(NEMA 5-20R) commercial grade conforming to NEMA WD 1 and NEMA WD 6.
Provide 10 percent spare devices of each type shown on these plans if
receptacles are not interchangeable or will not permit field adjustment of
phase and circuit selection. General use receptacles are required to be of
the duplex configuration; unless otherwise indicated, special use
receptacles are required to be of the simplex configuration with the
blade/pin arrangement identified on the plans. Coordinate the color of
receptacle bodies with the color of the panel trim. Isolated ground
receptacles must be orangeorhave distinct markings. Furniture receptacles
whose building power supply circuit is controlled by an energy management
system, timer, or some other automatic means or are provided with local
automatic control, will be identified using the standard symbol shown in
NFPA 70 Figure 406.3(E); each outlet on a multi-outlet receptacle shall be
identified individually. Provide field applied identification that is
permanent; stick-on or non-setting adhesives are not acceptable. Provide 5
SECTION 12 59 00 Page 15
Bldg 615 FSH19B615
percent spare devices for each configuration and type of receptacle.
Provide a minimum of 5 receptacle removal tools for systems that require
special tools for proper receptacle removal.
2.12.2.2 Power Cabling Variations
The paragraph Power Distribution has identified specific cabling
configurations. Since universal conventions have not been established,
variant configurations available from various manufacturers will be
considered. Alternates shall allow the same circuiting, device
connections, neutral and ground separation, and upstream feeder connections
as shown on the plans. See paragraph ALTERNATE DESIGN. An example of an
acceptable variation includes the use of a manufacturer's configuration
which allocates individual conductors differently, but which has the same
quantity of conductors and allows devices to be physically connected in the
field as shown on the plans. It is not necessary that the manufacturer's
labeling codes or terminology match the designations used on project plans
or in the specifications; however, neutrals and grounds shall have
insulation color coded per standard practice or be provided with tags,
colored tape, colored ribbons or similar identification. (The reference to
"dedicated" conductors in this specification pertains to circuit
connections upstream and load connections downstream of panels; it is not
necessary that manufacturer's designations correspond.)
2.12.3 Electrical Connections
2.12.3.1 Internal Connections
Utilize hardwired connections for internal panel-to-panel power
connections and provide the powered configurations shown on the drawings.
2.12.3.2 Connections to Building Services
Supply external power and communications services to the panels via hard
wired base entry junction box assemblies. Extend wiring from building
services to the entry modules or panel bases in metal conduit or tubing or
in flexible liquidtight conduit 6 foot maximum. Do not use cord and plug
assemblies for any portion of external links. External wiring must conform
to Section 26 20 00 INTERIOR DISTRIBUTION SYSTEM.
2.12.4 Wire Management
Provide wire management capability at all workstations and accommodate all
cable types specified, including the applicable manufacturer required
bending radius at corners. Design raceways and interfaces to the raceways
to accommodate the bend radius as shown in TIA-569 for Category 6 and fiber
optic cables communication wiring whichever is greater. Copper and fiber
cabling shall meet the requirements of Section 27 10 00 BUILDING
TELECOMMUNICATIONS CABLING SYSTEM. The capability may be accomplished by
cable access cutouts (1 minimum per work surface), covered wire management
troughs in vertical end panels, horizontal wiring troughs, internal
midpanel (beltline) raceways, or rear gaps (between the back edge of the
work surface and the facing support panel). Provide grommet kits or
another suitable finish arrangement for all cable cutouts. Provide
accessories for an externally mounted vertical and horizontal wire
management and concealment system as recommended by the manufacturer.
Supply horizontal wire managers for mounting under all work surfaces.
Attach the wire managers either to the underside of the work surface or to
the vertical panel without damaging the face. Exposed or loose wiring will
SECTION 12 59 00 Page 16
Bldg 615 FSH19B615
not be acceptable. Wire managers must be prefinished and secure, conceal,
and accommodate outlet cords as well as electrical and communications
wiring. Wire channels are required to match color of panel trim, attach by
means of clip-on attachment, and conceal wires routed vertically. Separate
power wiring from communication wiring by use of separate raceways or by
placement of channels in joint use troughs or wireways.
2.12.5 Circuit Layout
Provide the circuit layout for workstations on the drawings. Connect
devices to the designated circuits in the neutral, ground, and automatic
control configurations indicated. Connections must be made to the building
electrical distribution system as shown on the contract drawings and in
accordance with Section 26 20 00 INTERIOR DISTRIBUTION SYSTEM.
2.12.6 Task Lighting
Provide task lights with light emitting diode (LED) technology to include a
built-in reflector and shielding device that prevents direct glare into an
occupant's eyes when they are in a typical working position. Provide
adjustable arm task lights with adjustable, fully articulated and balanced
head and arms, minimum 10 inch adjustable arm range, linear, circular, or
compact fluorescent lamp technology, cord set for plug in, built in
reflector, that is freestanding. It is required that lights be a
standard component of the manufacturer's workstation products, and the ends
of the task light length can not extend beyond the edges of the overhead
cabinet. Enclose task light power cords within vertical wire cover or
clips. Luminaires shall be UL approved for use in the configurations
indicated on the drawings.
2.12.6.1 Luminaire Configuration
Provide luminaires and lamps as specified in Section 26 51 00 INTERIOR
LIGHTING and modified herein. For undershelf or undercabinet lighting,
provide luminaires that arelight emitting diode (LED) type and have
prismatic lenses, baffles, or other shielding device configured to minimize
glare by shielding the lamp from view of the seated user. For adjustable
arm task lights, provide luminaires that are LED type and have prismatic
lenses, baffles, or other shielding device configured to minimize glare by
shielfing the lamp from view of the seated user. For fluorescent-type
luminaires, provide built-in reflectors. Provide task lights for each
workstation with a minimum of 60 footcandles of light (horizontally
measured) without veiling reflections, on the work surface directly below
and a maximum of 20 inches from the luminaire. Easily removable diffusers,
grilles, or other coverings are required to allow for cleaning and
relamping. For LED-type task lighting, power consumption shall not exceed
8 watts per foot. Correlated Color Temperature (CCT) of task lighting
shall match the CCT of the ambient room lighting. Provide an easily
accessible on-off switch and one ballast or driver per luminaire. A
variable intensity control is acceptable if the low setting is equivalent
to "off" with zero energy consumption. Multiple level switching is also
acceptable. For LED type technology, ganged luminaires or shared drivers
are permitted for up to 4 continuous feet in length. A single driver
designed for use with an individual LED housing of greater than 4 feet in
length is allowed.
2.12.6.2 Wiring
Provide each luminaire with a 6 foot minimum, factory installed, heavy duty
SECTION 12 59 00 Page 17
Bldg 615 FSH19B615
electrical cordset with a grounded plug for luminaries that are mounted on
the same wall as the receptacle. Provide luminaires mounted on non-powered
wall with a 9 foot minimum, factory installed heavy duty electrical cordset
with a grounded plug. Direct or hard wire connections are not acceptable.
Unless otherwise indicated, conceal cord. Built-in cord concealment is
required within panels or utilize field installed, manufacturer approved
accessories. Cords may be extended through dedicated channels located at
any point within panels or may be placed in vertical slots or in the space
between panels if held in place by retainers and concealed by a cover
plate. Vertical wire managers are required to be prefinished and cut to
size and shall extend from the task light level down to the top of the work
surface below the task light. Attach each manager to a panel vertical edge
or connector strip without damage to the surfaces.
2.12.6.3 Control Device
For furniture with automatically-controlled building supply power circuits,
task lighting shall be connected to an automatically-controlled circuit.
2.12.7 Communications
Communications wiring will be extended to, and installed in, the
electrified panels as shown on the plans. Install communications jacks at
designated locations. Provide a communication consolidation point at the
end of the cubicle. The consolidation point will consist of a 48 port
patch panel that is rated for Category 6. The panel that covers the
consolidation panel is required to be lockable with all locks keyed alike.
These locks must not be keyed the same as any other item associated with
the workstations. Communications work may be performed in conjunction with
the installation of workstations or may be separately executed at the
Contractor's option; however, equipment, materials, and installation must
conform to the requirements of Section 26 20 00 INTERIOR DISTRIBUTION
SYSTEM Section 27 10 00 BUILDING TELECOMMUNICATIONS CABLING SYSTEM, and
properly coordinate all interfaces.
2.12.8 Special Systems
Provide management for secure and nonsecure power, computer and
telecommunications cabling through designated raceway systems. Separate
secure distribution from nonsecure distribution in accordance with details
shown on the plansby running secure lines along top located raceway and
nonsecure along the bottom of the workstation panel.
PART 3 EXECUTION
3.1 INSTALLATION
Install the workstations using certified installers in accordance with
manufacturer's recommended installation instructions. A licensed
electrician is required to hardwire the workstations. Install workstation
components level, plumb, square, and with proper alignment with adjoining
furniture. Securely interconnect and attach components to the building
where required. Provide three sets of special tools and equipment
necessary for the relocation of panels and other components. Verify that
equipment is properly installed, connected, and adjusted.
3.2 CLEANING
Provide cleanup as specified in Section 01 78 00 CLOSEOUT SUBMITTALS. Upon
SECTION 12 59 00 Page 18
Bldg 615 FSH19B615
completion of installation, clean and polish all products and leave the
area in a clean and neat condition. Any defects in material and
installation are required to be repaired, and damaged products that cannot
be satisfactorily repaired are required to be replaced. Submit three sets
of Maintenance Manuals describing proper cleaning and minor repair
procedures.
-- End of Section --
SECTION 12 59 00 Page 19
Bldg 615 FSH19B615
SECTION 14 24 23
HYDRAULIC PASSENGER ELEVATORS
PART 1 GENERAL
1.1 REFERENCES
The publications listed below form a part of this specification to the
extent referenced. The publications are referred to within the text by the
basic designation only.
AMERICAN WELDING SOCIETY (AWS)
AWS D1.1/D1.1M (2015; Errata 1 2015; Errata 2 2016)
Structural Welding Code - Steel
ASME INTERNATIONAL (ASME)
ASME A17.1/CSA B44 (2016) Safety Code for Elevators and
Escalators
ASME A17.2 (2017) Guide for Inspection of Elevators,
Escalators, and Moving Walks Includes
Inspection Procedures for Electric
Traction and Winding Drum Elevators,
Hydraulic Elevators, and Escalators and
Moving Walks
ASME B16.11 (2016) Forged Fittings, Socket-Welding and
Threaded
ASME B16.9 (2012) Standard for Factory-Made Wrought
Steel Buttwelding Fittings
ASTM INTERNATIONAL (ASTM)
ASTM A106/A106M (2014) Standard Specification for Seamless
Carbon Steel Pipe for High-Temperature
Service
ASTM A53/A53M (2012) Standard Specification for Pipe,
Steel, Black and Hot-Dipped, Zinc-Coated,
Welded and Seamless
INSTITUTE OF ELECTRICAL AND ELECTRONICS ENGINEERS (IEEE)
IEEE C62.41 (1991; R 1995) Recommended Practice on
Surge Voltages in Low-Voltage AC Power
Circuits
INTERNATIONAL CODE COUNCIL (ICC)
ICC IBC (2018) International Building Code
SECTION 14 24 23 Page 1
Bldg 615 FSH19B615
NATIONAL ELEVATOR INDUSTRY, INC. (NEII)
NEII-1 (2000; R thru 2017) Building
Transportation Standards and Guidelines,
including the Performance Standards Matrix
for New Elevator Installation
NATIONAL FIRE PROTECTION ASSOCIATION (NFPA)
NFPA 101 (2018; TIA 18-1) Life Safety Code
NFPA 70 (2017; ERTA 1-2 2017; TIA 17-1; TIA 17-2;
TIA 17-3; TIA 17-4; TIA 17-5; TIA 17-6;
TIA 17-7; TIA 17-8; TIA 17-9; TIA 17-10;
TIA 17-11; TIA 17-12; TIA 17-13; TIA
17-14) National Electrical Code
NFPA 70E (2018; TIA 18-1; TIA 81-2) Standard for
Electrical Safety in the Workplace
NFPA 72 (2016) National Fire Alarm and Signaling
Code
U.S. DEPARTMENT OF DEFENSE (DOD)
UFC 3-560-01 (2017) Operations and Maintenance:
Electrical Safety
U.S. NATIONAL ARCHIVES AND RECORDS ADMINISTRATION (NARA)
36 CFR 1191 Americans with Disabilities Act (ADA)
Accessibility Guidelines for Buildings and
Facilities; Architectural Barriers Act
(ABA) Accessibility Guidelines
1.2 SUBMITTALS
Government approval is required for submittals with a "G" designation;
submittals not having a "G" designation are for Contractor Quality Control
approval. Submittals with an "S" are for inclusion in the Sustainability
eNotebook, in conformance with Section 01 33 29 SUSTAINABILITY REPORTING.
Submit the following in accordance with Section 01 33 00 SUBMITTAL
PROCEDURES:
SD-02 Shop Drawings
Elevator System; G
Elevator Components; G
Elevator Machine; G
Elevator Controller; G
Wiring Diagrams; G
SD-03 Product Data
Elevator and Accessories
SECTION 14 24 23 Page 2
Bldg 615 FSH19B615
Elevator Components
Data Sheets
Elevator Microprocessor Controller; G
SD-05 Design Data
Emergency Power Systems
Heat Loads
Reaction Loads
SD-07 Certificates
Elevator Parts and Components Price Lists; G
Warranty
Endorsement Letter
Welders' Qualifications
Elevator Controller Certification; G
SD-10 Operation and Maintenance Data
Elevator, Data Package 4; G
Maintenance Control Program (MCP); G
Software and Documentation; G
Submit in accordance with Section 01 78 23 OPERATION AND
MAINTENANCE DATA and 01 78 24.05 20 FACILITY OPERATION AND
MAINTENANCE SUPPORT INFORMATION.
1.2.1 Shop Drawing Requirements
Provide assembly and arrangement of elevators, accessories, and elevator
components. Show location of elevator machine in elevator machine room
(MR) or machinery space (MS). Show location of elevator controller in
elevator machine room. Provide details for materials and equipment,
including but not limited to operating and signal fixtures, doors, door and
car frames, car enclosure, controllers, motors, guide rails and brackets,
layout of hoistway in plan and elevation, and other layout information and
clearance dimensions.
1.2.2 Product Data Requirements
Provide manufacturers' product data for all elevator components, including
but not limited to the following: elevator controller, hydraulic pump unit,
hydraulic pump and motor, hydraulic cylinder, hydraulic piping and
fittings, car and hall fixture buttons and switches, cab and machine room
or control room communication devices, door operator, door protection
system, car roller guides, and buffers. For data sheets, provide document
identification number or bulletin number, published or copyrighted prior to
SECTION 14 24 23 Page 3
Bldg 615 FSH19B615
the date of contract bid opening. Provide controller manufacturer's
published procedures for performance of each and all testing required by
ASME A17.1/CSA B44.
1.2.3 Design Data
1.2.3.1 Reaction Loads
Provide calculations by registered professional engineer for reaction loads
imposed on building by elevator system. Demonstrate calculations complying
with ASME A17.1/CSA B44
1.2.3.2 Heat Loads
Provide calculations from elevator manufacturer, or by registered
professional engineer, for total anticipated heat loads generated by all of
the elevator equipment.
1.2.4 Welders' Requirements
Comply with AWS D1.1/D1.1M, Section 5. Include certified copies of field
welders' qualifications. List welders' names with corresponding code marks
to identify each welder's welding work
1.2.5 Maintenance Control Program (MCP)
For each elevator, prepare and provide a written Maintenance Control
Program (MCP) that complies with ASME A17.1/CSA B44 Section 8.6, including
written documentation that details the test procedures for each and every
test that is required to be performed by ASME A17.1/CSA B44. Assemble all
MCP documentation, and supporting technical attachments, in a single MCP
package and provide in both electronic and hard copy. Assemble entire hard
copy MCP in 3-ring binders. For each elevator provided, the MCP must
include only documentation and instruction that apply to the elevator
specified.
For each elevator, provide an additional, separate binder that includes all
maintenance, repair, replacement, call back, and other records required by
ASME A17.1/CSA B44. The records binder must be kept in the elevator
mechanical room, maintained by elevator maintenance and service personnel,
and be available at all times to authorized personnel.
Provide detailed information regarding emergency service procedures and
elevator installation company personnel contact information. Provide a
listing of all tools to be provided to the Contracting Officer as
components of the elevator system.
1.3 QUALITY ASSURANCE
1.3.1 Qualification
Provide a designed and engineered elevator system by an elevator contractor
regularly engaged in the installation of elevator systems. Provide
elevator components manufactured by companies regularly engaged in the
manufacture of elevator components. Utilize only licensed and certified
elevator personnel for the installation, adjusting, testing, and servicing
of the elevators.
SECTION 14 24 23 Page 4
Bldg 615 FSH19B615
1.3.1.1 Elevator Contractor's Elevator Technicians
For elevator installations in the United States, including United States
territories, perform all elevator related work under the direct guidance of
a state certified elevator technician with a minimum of three years of
experience in the installation of elevator systems of the type and
complexity specified in the contract documents. Provide an endorsement
letter from the elevator manufacturer, certifying that the elevator
specialist is qualified. All elevator technicians must carry a current
certification issued by one of the following organizations:
a. National Association of Elevator Contractors (NAEC)
b. National Elevator Industry Education Program (NEIEP)
1.3.2 Manufacturers' Technical Support
Provide elevator components from manufacturers that provide factory
training and online and live telephone elevator technical support to any
elevator installation, service, and maintenance contractor. Provide
elevator components from manufacturers that guarantee accessibility to all
replacement and repair parts and components to any elevator installation,
service, and maintenance contractor. Use only elevator component
manufacturers that provide current published price lists for all elevator
parts and components.
1.3.3 Operation and Maintenance Data
Assemble all shop drawing and product data material into O&M Data Packages
in accordance with Article SUBMITTALS. Provide two complete O&M Data
Packages in hard copy and two complete electronic O&M data packages on
separate CDs, in PDF format. Provide all O&M Data Packages to Contracting
Officer. Include controller diagnostic documentation and software as
required under Article CONTROL EQUIPMENT.
1.3.4 Wiring Diagrams
Provide complete wiring diagrams and sequence of operations, which show
electrical connections and functions of elevator systems. Provide one set (
11 inch by 17 inch minimum size) of wiring diagrams, with individual sheets
laminated in plastic and assembled in binder, to be stored in the machine
room or control room cabinet. Provide one additional hard copy set and two
complete electronic sets on separate CDs, in PDF format. Provide all
wiring diagram sets to the Contracting Officer. Coded diagrams are not
acceptable unless fully identified.
1.3.5 Machine Room/Control Room Cabinet
For storage of O&M Data Packages and Wiring Diagrams, provide locking metal
cabinet with a minimum size of 20 inch W by 12 inch D by 30 inch H.
Cabinet must be sized large enough to accommodate all O&M Data and hardware
required in paragraphs OPERATION AND MAINTENANCE DATA and WIRING DIAGRAMS.
Secure cabinet to machine room or control room wall.
1.4 NEW INSTALLATION SERVICE
Provide elevator warranty service in accordance with the manufacturer's
maintenance plan, warranty requirements and applicable safety codes, for a
period of 12 months after the date of acceptance by Contracting Officer.
SECTION 14 24 23 Page 5
Bldg 615 FSH19B615
Perform this work during regular working hours. Provide supplies and parts
to keep elevator system in operation. Perform service only by factory
trained personnel. Provide Monthly services to include repairs,
adjustments, greasing, oiling, and cleaning. Provide service log in
elevator machine room or control room and update Monthly, throughout the
one-year warranty period.
Provide 24-hour emergency service, with one hour on-site response time,
during this period without additional cost to the Government.
1.4.1 Periodic Elevator Certification Inspection and Testing
Provide elevator mechanic to support QEI Certified Elevator Inspector in
the periodic six-month and the annual Category 1 elevator certification
inspection and testing. Perform Category 1 inspection and testing no
greater than 30 days prior to the end of the warranty period. Perform all
elevator certification testing in the presence of QEI Certified Elevator
Inspector.
In conjunction with the testing noted above, test systems for Emergency
Power Operation, Earthquake Emergency Operation, and Hospital Emergency
Commandeering Service Operation, as applicable. Schedule so that testing
does not interfere with building operations.
1.5 FIRE PROTECTION SYSTEM
Coordinate interface between building fire protection system and elevator
controls.
Additional fire protection requirements are located in: Section
28 31 74.00 20 INTERIOR FIRE DETECTION AND ALARM SYSTEM; Section
21 13 13.00 20 WET PIPE SPRINKLER SYSTEM, FIRE PROTECTION; and Section
26 20 00 INTERIOR DISTRIBUTION SYSTEM.
1.5.1 Fire Alarm Initiating Devices
Fire alarm initiating devices are specified in Section 28 31 74.00 20
INTERIOR FIRE DETECTION AND ALARM SYSTEM, including conduit and wiring from
each detector to fire protection addressable modules in elevator machine
room or control room.
1.5.2 Fire Sprinklers
Provide fire sprinklers in accordance with all applicable safety codes and
with Section 21 13 13.00 20 WET PIPE SPRINKLER SYSTEM, FIRE PROTECTION.
Provide shutoff valve, check valve, and non-adjustable, zero time-delay
flow switch, in each sprinkler line immediately outside of each machine
room, control room, and hoistway, as applicable. Provide inspectors' test
valve for periodic testing of flow switch and shunt trip disconnect.
Pipe sprinkler piping serving these spaces in a series manner with no
laterals. Locate inspectors' test connection at the end of pipe runs such
that operation of the test connection will purge air from system piping.
1.5.3 Shunt Trip Disconnect
Provide flow switches specified in paragraph FIRE SPRINKLERS to comply with
ASME A17.1/CSA B44 and NFPA 72 for shunt trip of the main line power
supply. For each elevator, provide control wiring connecting the flow
SECTION 14 24 23 Page 6
Bldg 615 FSH19B615
switch to a shunt trip equipped circuit breaker located in the elevator
machine room or control room. Upon flow of water, flow switch will
instantaneously cause opening of the shunt-trip circuit breaker and remove
power from the elevator. Flow switch must also send a signal to fire alarm
control panel to indicate water flow condition.
PART 2 PRODUCTS
2.1 ELEVATOR DESCRIPTION
Provide elevator system that complies with ASME A17.1/CSA B44 in its
entirety, ASME A17.2 in its entirety, and additional requirements specified
herein. Provide elevator system that meets or exceeds the NEII-1 Ride
Quality Performance Standards Matrix (RQPSM). Comply with the RQPSM
"Intermediate Performance" criteria.
Provide and install elevators in accordance with 36 CFR 1191 - ABAAS,
ICC IBC, IEEE C62.41, NFPA 70 and NFPA 101 requirements.
2.1.1 Elevator Design Parameters
2.1.1.1 Elevator No. #1 - Emergency Medical Service Accessibility (EMSA)
Provide elevator(s) with minimum size and arrangement to accommodate an
ambulance stretcher 24-inch by 84-inch with not less than 5-inch radius
corners, in the open, horizontal position.
a. Type: Holeless
b. Rated load: 3500 lb.
c. Rated Speed: 150 fpm
d. Car Door Type: Single-speed side slide.
e. Car Door Opening Width: 3 ft.-6 in. minimum.
2.1.2 Cab Enclosure and Hoistway Entrance Assemblies
Provide finishes as listed below:
a. Floor; Porcelain.
b. Walls; laminated plastic on plywood. Provide each cab wall with
equally spaced and equally sized wall panels. All wall panel fasteners
must be concealed.
Wall trim; stainless steel.
Accessories; Provide hand rails on full length of back wall and
side walls of elevator cab.
c. Car doors, car door returns, and wall reveals; stainless steel.
d. Ceilings; prefinished steel panels.
Ceiling frame; prefinished steel.
e. Hoistway Entrance Assembly Material and Finishes; stainless steel.
SECTION 14 24 23 Page 7
Bldg 615 FSH19B615
2.2 ELEVATOR OPERATION
ASME A17.1/CSA B44, Introduction, Section 3, Definitions.
2.2.1 Single, Two-Stop, Automatic Operation
Provide Single Two-Stop Automatic Operation.
2.3 SPECIAL OPERATION AND CONTROL
Provide the following special operations and control systems.
2.3.1 Keys for Elevator Key Switches
Provide a minimum of twelve keys per unique cylinder used on all key
switches for a single elevator. If there is more than one elevator,
additional keys will not be required unless there are additional unique
lock cylinders. Provide keys with brass or fiberglass tags marked
"PROPERTY OF THE U.S. GOVERNMENT" on one side with function of key or
approved code number on the other side.
2.3.2 Firefighters' Emergency Operation (FEO)
Provide FEO equipment and signaling devices. The designated level for the
FEO Phase I key operated switch is the ground floor. In the FEO Phase I
fixture, provide FEO Operating Instructions.
2.3.2.1 Firefighters' Emergency Operation (FEO) Key Box
Provide flush mounted, locking, FEO Key Box of a minimum size of 5 inch W
by 9 inch H by 1.5 inch D. Install at a height of 6 feet above floor level
and directly above the FEO Phase I key switch. Provide box equipped with
lock that uses the FEO K1 key.
2.3.3 Hoistway Access Operation
Provide hoistway access operation with switches at top and bottom terminal
landings. Locate switch 6 feet above floor level, within 12 inches of
elevator hoistway entrance frame or with the ferrule exposed when located
in the elevator entrance frame.
2.3.4 In-Car Inspection Operation
Provide In-Car Inspection Operation.
2.3.5 Independent Service
Provide exposed key-operated switch in car operating panel to enable
independent service and simultaneously disable in-car signals and
landing-call responses. Provide indicator lights that automatically
illuminate during independent service. For duplex or group operation, if
one car is removed from group another car will respond to its hall calls.
2.3.6 Selective Door Operation
For elevator with one or more rear openings at same level as front opening,
provide full-selective operation with car and door operating buttons
clearly marked for front and rear openings, front and rear car button for
SECTION 14 24 23 Page 8
Bldg 615 FSH19B615
each such floor, and front and rear "DOOR OPEN" and "DOOR CLOSE" buttons.
Only door for which the button was operated opens or closes.
2.4 ELEVATOR DRIVE SYSTEM
Provide hydraulic elevator drive system, including pump unit, piping,
cylinder/plunger assembly, and associated equipment, which will operate at
a maximum working pressure of 500 psi or less. Provide complete elevator
system that meets or exceeds the NEII-1 Ride Quality Standard, including
elevator ride quality and noise levels in car and in elevator machine room
and machinery space.
2.4.1 Hydraulic Pump Unit
Provide self-contained pump unit, including oil-hydraulic elevator pump,
electric motor, suction-line oil strainer, and structural steel outer base
with tank supports and isolation pads. Provide oil tank capacity for full
plunger displacement plus at least 10 gallons. Provide means to maintain
oil temperature between 100 and 130 degrees F regardless of ambient
temperature. Limit acoustic output in elevator machine room and machinery
space to 80 dbA.
2.4.1.1 Pump Motor
Provide intermittent-duty pump motor rated at 120 starts/hour. Provide
motor that is sized so that the motor amperage does not exceed the motor
data tag amperage in any operating condition, exclusive of acceleration and
deceleration. Provide minimum of one mega ohm insulation resistance
between conductors and motor frame. Provide motor and pump nameplate and
data tags permanently mounted on the outside of the pump unit frame, with
all data viewable without the use of mirrors or other tools.
2.4.2 Hydraulic Controls and Equipment
Provide control valve, overspeed safety valve, blowout-proof muffler, and
hydraulic pump discharge strainer in the hydraulic oil supply line.
Provide two 1/4 turn, ball valve type manual shutoff valves. Provide one
in the elevator hoistway pit and one in the elevator machine room or
machinery space.
2.4.2.1 Hydraulic Control Valve
Provide constant-velocity, down-speed regulated, control valve. Down-speed
regulated control valve allows the car to travel at the same speed in the
down direction, regardless of the load on the elevator. In addition, the
hydraulic control valve must have built-in adjustment capability to operate
the elevator at 140 percent of rated speed to facilitate periodic testing
of the overspeed safety valve.
2.4.2.2 Hydraulic Overspeed Safety Valve
Provide overspeed safety valve in hydraulic oil supply line, directly
adjacent to the hydraulic cylinder. Provide threaded pipe connections
between the hydraulic cylinder and the overspeed valve. Provide valve
equipped with manufacturer's manual shutoff feature. Overspeed valve must
not be equipped with a manual or automatic lowering feature. Provide
adjustable valve with means to seal adjustment after inspection and testing
by certified elevator inspector.
SECTION 14 24 23 Page 9
Bldg 615 FSH19B615
2.4.3 Hydraulic Piping and Accessories
Provide ASTM A53/A53M or ASTM A106/A106M, Schedule 80, black steel piping
with ASME B16.9 or ASME B16.11 fittings for supply piping. Extend schedule
80 piping from the pump control valve body, inside the pump unit, to the
hydraulic cylinder in the hoistway. Provide welded or threaded forged pipe
fittings for all fittings and components of the hydraulic oil supply
line. ___. Provide hangers or supports for all piping and components.
2.4.3.1 Containment of Hydraulic Oil Supply Line
Protect all portions of hydraulic oil supply line that are installed below
ground, including portions encapsulated in concrete or covered by
construction, with continuous, Schedule 80, PVC. Inside diameter of PVC
must be 3 inches larger than the outside diameter of the hydraulic oil
supply line pipe and couplings.
2.4.4 Hydraulic Elevator Type
Provide a Holeless type hydraulic elevator.
2.4.4.1 Cylinder-Plunger (Jack) Unit
Provide the following jack type: Twin post holeless telescopic 1-stage.
Two jacks piped together, mounted one on each side of the car with each
having two telescopic sections designed to extend in a synchronized manner
when oil is pumped into the assembly. Each jack section will be guided
from within the casing or the plunger assembly used to house the section.
Each plunger shall have a high pressure sealing system which will not allow
for seal movement or displacement during the course of operation. A
follower guide shall be furnished for the top of the lower two plungers and
be guided by rollers running inside a steel guide channel which is firmly
attached to the guide rail system. This plunger guide system shall
maintain a stabilized support for the plunger sections. Each jack assembly
shall have check valves built into the assembly to allow for automatically
re-syncing the three plunger sections by moving the jack to its fully
contracted position .
SECTION 14 24 23 Page 10
Bldg 615 FSH19B615
2.4.5
2.4.5.1
2.4.5.2
2.4.5.3
2.4.5.4
2.4.5.5
2.5 CONTROL EQUIPMENT
Enclose all elevator control equipment in factory-primed and baked-enamel
coated sheet-metal cabinets with ventilation louvers and removable or
hinged doors. Mount cabinets at a height of 10 inches above machine room
or control room finish floor.
2.5.1 Motor Control Equipment
Provide elevator motor control with electronic, soft-start motor starter.
2.5.2 Elevator Microprocessor Controller
For each individual elevator controller, and for each group controller,
provide a microprocessor controller that complies with the following
paragraphs. Provide controller(s) package that includes all hardware and
software required for the installation, maintenance, and service of the
elevator, in its' entirety. Provide verification of technical support
service that the controller manufacturer provides to any licensed elevator
installation, service, and maintenance company.
Provide an elevator controller from a manufacturer that provides
comprehensive factory training to include controller installation,
adjustment, service, and maintenance. The training must be identified as
available to any licensed elevator contractor. Provide verification of an
established and documented training schedule, with pricing, for factory
training classes that manufacturer has provided for a minimum period of one
year prior to contract award date.
The elevator controller must be identified as available for purchase and
installation by any licensed elevator contractor. All components, parts,
diagnostic tools, and software must be available for purchase and
installation and use by any licensed elevator contractor; "exchange-only"
provisions for the purchase of spare parts are not acceptable. The
elevator controller manufacturer must publish an industry competitive price
SECTION 14 24 23 Page 11
Bldg 615 FSH19B615
listing for all controller parts, diagnostic tools, and software.
Provide verification of telephone and internet based technical support
service that the elevator controller manufacturer provides to any licensed
elevator installation, service, and maintenance company at an industry
competitive price. The service must include live telephone based technical
support for installation, adjustment, maintenance, and troubleshooting of
the elevator controller and related elevator components. The service must
be available during standard working hours.
Provide an elevator controller that is designed to automatically
reestablish normal elevator operation following any temporary loss of
power, regardless of duration.
2.5.2.1 Elevator Controller Interface Cabinet
For each individual elevator microprocessor controller, provide a separate
elevator control cabinet with an integrated human interface system. For
group elevator installations, a single cabinet and interface system with
full access to each elevator controller may be utilized. The separate
controller interface cabinet must be supplied by the elevator controller
manufacturer and include a minimum 12 inch wide keyboard and a minimum 10
inch monitor. The elevator controller interface cabinet must comply with
arc-flash protection requirements of NFPA 70E and UFC 3-560-01.
2.5.2.1.1 Elevator Microprocessor Human Interface
The interface system must provide complete elevator controller interface
capability and must include the elevator controller manufacturer's
comprehensive package of installation and diagnostic software. The
microprocessor interface system must provide unrestricted access to all
parameters, all levels of adjustment, and all flags necessary for
installation, adjustment, maintenance, and troubleshooting of each elevator
and for the elevator group. All software programming must be stored in
non-volatile memory. The elevator controller fault log must provide
non-volatile memory fault log storage of all faults, trouble calls, and
fault history for a minimum of one year and the ability to download or
print the fault log. The controller interface must also provide the
capability to display and diagnose trouble calls, faults, and shutdowns.
Expiring software, degrading operation, and "key" access controls are not
acceptable.
2.5.2.2 Software and Documentation
Provide three copies of the manufacturer's maintenance and service
diagnostic software, with complete software documentation, that will enable
the same level of unrestricted access to all controllers of the same make
and model, regardless of the installation date or location. Provide signed
certification, from the manufacturer's corporate headquarters, that
guarantees that the microprocessor software and access system will not
terminate the unlimited and unrestricted access at any future date.
2.5.2.3 Elevator Controller Certification
For elevator installations in the United States, including United States
territories, provide an elevator microprocessor controller that has a
current certificate of safety code compliance issued by the Technical
Standards and Safety Authority (TSSA), Toronto, Canada.
SECTION 14 24 23 Page 12
Bldg 615 FSH19B615
2.6 OPERATING PANELS, SIGNAL FIXTURES, AND COMMUNICATIONS CABINETS
For all panels and fixtures, provide identical and uniform panel and
fixture design, material, finish, and components for all elevators. For
all panels and fixtures, legibly and indelibly identify all buttons,
devices, and all operating positions for each device. Use engraving and
backfilling, or photo etching, for button and device designations. Do not
use attached signs. Provide elevator manufacturers' standard grade for all
key switches unless otherwise specified. All illuminating panels and
fixture components must utilize LED lighting for energy efficiency.
2.6.1 Car and Hall Buttons
For all cab and landing fixture buttons, provide industry-standard, vandal
resistant push buttons with positive-stop assembly design. Buttons must be
minimum 3/4 inch diameter, satin-finish stainless steel, with illuminating
LED halo.
2.6.2 Passenger Car-Operating Panel
Provide each car with one car operating panel that contains operation
controls and communication devices. Provide exposed, flush mounted buttons
for the controls identified in subparagraph PASSENGER CONTROLS. Provide a
lockable service cabinet for the controls listed in subparagraph SERVICE
CONTROLS. Use engraving and backfilling or photo etching for button and
switch designations. Do not use attached signs.
2.6.2.1 Passenger Controls
In addition to ASME A17.1/CSA B44 requirements, provide the following
operating controls, identified as indicated:
a. Illuminating car-call buttons identified to correspond to landings
served by the elevator.
b. "DOOR OPEN" and "DOOR CLOSE" buttons. For front and rear openings at
the same floor, include the identification "F" and "R" for each opening.
c. Red, illuminating "ALARM" button.
d. Key-operated "Independent Service" switch.
e. "Help" communication device to include communication between elevator
cab and elevator machine room or control room.
2.6.2.2 Service Controls
In addition to ASME A17.1/CSA B44 requirements, provide the following
operating controls, identified as indicated:
a. Provide a key-operated, three-position switch for "In car Inspection
Operation" and "Hoistway Access". The center switch position will
provide normal, automatic operation.
b. "Car Light" switch.
c. "Car Fan" switch with two speed settings identified.
d. 120-volt ac 60 Hz single-phase duplex electrical outlet of
SECTION 14 24 23 Page 13
Bldg 615 FSH19B615
ground-fault-circuit-interrupt (GFCI) design.
2.6.2.3 Certificate Window
Provide a minimum 4 inch wide by 6 inch high certificate window for
elevator inspection certificate. Locate window in the Service Controls
door of the Car Operating Panel.
2.6.2.4 Emergency Signaling Devices
Provide an audible signaling device, operable from the Car Operating Panel
button marked "ALARM". The audible signaling device must have a sound
pressure rating between 80 and 90 dBA at 10 ft. Provide battery backup
power capable of operating the audible signaling device for at least one
hour.
2.6.3 Elevator In-Car Position Indicators
For all elevators, provide illuminating position indicator in the Car
Operating Panel.
2.6.4 Elevator In-Car Direction Indicators
For 2-stop elevator installations, provide visual direction indicators and
audible car arrival signal in the elevator car door jamb, in accordance
with ABA Standards. Visual indicators must be visible from the hall call
fixture.
2.6.5 Hall Call Landing Fixtures
Provide a hall call fixture adjacent to each elevator. Provide a single
push-button for terminal landings and dual push-buttons, up and down, at
intermediate landings.
2.6.5.1 Designated Landing Hall Call Fixture
2.6.5.1.1 Location of COMMUNICATION MEANS FAILURE (CMF) Visual Signal
When required by ASME A17.1/CSA B44, provide an elevator CMF audible and
illuminating signal, and reset switch, in the FEO Designated Landing hall
call fixture. Mount the signal and reset switch at a minimum of 7 inches
above the "UP" hall call button.
2.6.5.1.2 COMMUNICATION MEANS FAILURE (CMF) Visual and Audible Signal
Operation
Provide a CMF visual and audible signal system that conforms to
ASME A17.1/CSA B44. Provide continuous verification of operability of the
telephone line and immediate activation of audible and visual signals when
verification means determines that the telephone line is not functioning.
Provide illumination of visual signal at one second intervals. Provide a
minimum of 65 dBA audible signal at 30 second intervals.
2.6.5.1.3 Firefighters' Emergency Operation Phase I Switch and Visual Signal
When required by ASME A17.1/CSA B44, provide an elevator Firefighters'
Emergency Operation Phase I switch and illuminating visual signal in the
FEO Designated Landing hall call fixture. Provide FEO Phase I visual
signal that is designed with intermittent, flashing, illumination when
SECTION 14 24 23 Page 14
Bldg 615 FSH19B615
actuated by the machine room, control room, or hoistway fire alarm
initiating device. Locate FEO Phase I key switch above the CMF visual
signal with a minimum of 6 inches vertical between the centerlines of the
CMF signal and the FEO Phase I key switch. Locate FEO Phase I visual
signal directly above the Phase I switch. In addition, locate Elevator
Corridor Call Station Pictograph at top of hall call fixture.
2.6.6 Elevator Car Position and Direction Indicators and Car Arrival Signal
For elevator installations with three or more stops, provide a separate
hall landing fixture that includes the visual elevator position indicator,
visual direction indicators, and audible car arrival signal, in accordance
with ABA Standards.
2.6.7 Designated Landing Elevator Identification Fixture
For duplex and group elevator installations, provide a separate elevator
identification fixture for each elevator, with identification engraved and
backfilled with a contrasting color. Number elevators from left to right,
as seen during primary approach from building main entrance to elevator
lobby. For multiple elevator groups, begin numbering with group that is
closest to the building main entrance.
2.7 CAR DOOR EQUIPMENT
2.7.1 Car Door Operator
Provide elevator door operator equipment and circuitry that is designed and
installed as discreet communication. Serial communication must not be used
for this system.
2.7.2 Infra-red Curtain Unit
Provide Infra-red Curtain Unit (ICU) with multiple infra-red beams that
protect to the full height and width of the door opening. Provide door
nudging operation.
2.8 PASSENGER ELEVATOR GUIDES, PLATFORM, AND ENCLOSURE
2.8.1 Roller Guides
Provide coil-spring loaded roller guide assemblies in adjustable mountings
on each side of car and counterweight frames in accurate alignment at top
and bottom of frames.
2.8.2 Car Enclosure Wall Panels, Return Panels, Doors, Entrance Columns,
and Transom
Provide 14 Gauge minimum stainless steel cab wall panels and entrance
components. Use same material and finish for all hoistway and car entrance
assemblies. Apply sound-deadening material on exterior of all cab wall
panels.
2.8.3 Car Enclosure Top
Provide reinforced, 12 gauge minimum steel car enclosure top. Provide
hinged emergency exit with lock that complies with the seismic risk zone 2
or greater design requirements of ASME A17.1/CSA B44. Locate emergency
exit hinge towards the rear of the elevator cab. Design and configure the
SECTION 14 24 23 Page 15
Bldg 615 FSH19B615
elevator cab interior ceiling to provide convenient and unobstructed access
to, and use of, emergency exit from inside the elevator cab.
2.8.4 Car Door
Provide 16 gauge minimum stainless steel car doors of sandwich construction
with flush surfaces on car and landing sides. Provide a minimum of 2 door
guide assemblies per door panel, one guide at leading and one at trailing
door edge with guides in the sill groove their entire length of travel.
2.8.5 Car Entrance Sill
Provide one piece cast nickel silver, stainless steel, or white bronze
entrance sill(s). Set sills level and flush with floor finish. Use same
material for hoistway and car entrance sills.
2.8.6 Cab Finish Floor
Provide cab finish floor with top of finish floor flush with the cab sill.
2.8.7 Car Fan
Provide 2-speed fan for car enclosure forced ventilation. Fan must be
mounted in the car enclosure top.
2.8.8 Car Lighting
Utilize LED lighting for elevator car interior illumination. Provide a
minimum of 10 foot-candles, measured at all areas of the car enclosure
floor. Provide automatic car lighting operation that will turn off car
lights after 3 minutes of inactivity. Car lights must automatically turn
on upon actuation of an elevator car or hall call.
2.8.9 Car Protection Pads and Hooks
Provide fire retardant, hanging car protection pads that provide protection
for all car interior wall panels. Provide permanently installed studs in
car that are designed for hanging the car protection pads in the car.
2.9 PASSENGER ELEVATOR HOISTWAY DOORS AND ENTRANCES
Provide hoistway entrance assemblies with a minimum 1-1/2 hour fire
rating. Use same material and finish for all hoistway and car entrance
assemblies.
2.9.1 Hoistway Entrance Frames
Provide 14 gage minimum stainless steel hoistway entrance frames. Solidly
grout uprights of entrance ways to height of 5 feet.
2.9.2 Hoistway Entrance Sills
Provide one-piece cast nickel silver, stainless steel, or white bronze
entrance sills. Set top of landing sill flush with top of finish floor.
Solidly grout under full length of sill. Use same material for all
hoistway and car entrance sills.
SECTION 14 24 23 Page 16
Bldg 615 FSH19B615
2.9.3 Hoistway Entrance Doors
Provide stainless steel non-vision construction hoistway entrance doors
with flush surfaces on car and landing sides. Provide a minimum of 2 door
guide assemblies per door panel, one guide at leading edge and one at
trailing edge with guides in the sill groove the entire length of door
travel. Use same material and finish for all hoistway and car entrance
assemblies.
2.9.4 Hoistway Entrance Door Track Dust Covers
Provide sheet metal hoistway door track dust covers at each landing. Dust
covers must cover top and hoistway side of door locks and door roller
tracks, and extend the full width of the door track and associated
hardware. Dust cover sections will not exceed 3 feet in length.
2.10 HOISTWAY EQUIPMENT
2.10.1 Car Guide Rails and Fastenings
Provide T-section type guide rails for car. Paint rail shanks with one
coat of black enamel.
2.10.2 Pit Equipment and Support Channels
Provide rail-to-rail pit channels to serve as mounting surface for main
guide rails , hydraulic cylinder and car buffers. Method of installation
of channels, brackets and buffer mounts must be such that pit waterproofing
is not punctured.
2.10.3 Pit "STOP" Switch
Provide push-to-stop/pull-to-run type pit "STOP" switch.
2.10.4 Traveling Cables
Suspend traveling cables by means of self-tightening webbed devices or
internal suspension members.
2.10.5 Hoistway Pit Ladder
Provide continuous horizontal rungs for the full height of the pit ladder.
PART 3 EXECUTION
3.1 INSTALLATION
Install in accordance with DOD design criteria, contract specifications,
manufacturer's instructions, NEII-1 Building Transportation Standards and
Guidelines, and all applicable building and safety code requirements.
3.1.1 Structural Members and Finish Materials
Do not cut or alter structural members. Do not alter finish materials from
manufacturer's original design. Restore any damaged or defaced work to
original condition.
SECTION 14 24 23 Page 17
Bldg 615 FSH19B615
3.1.2 Miscellaneous Requirements
Provide recesses, cutouts, slots, holes, patching, grouting, and
refinishing to accommodate elevator installation. Use core drilling to
drill all new holes in concrete. Finish work to be straight, level, and
plumb. During installation, protect machinery and equipment from dirt,
water, or mechanical damage. At completion, clean all work and spot paint.
3.2 FIELD QUALITY CONTROL
The Contractor will provide and utilize a third-party licensed and
certified Qualified Elevator Inspector (QEI) to conduct elevator
pre-acceptance inspection and testing. The QEI must perform inspections
and witness tests to ensure that the installation conforms to all
applicable safety codes and contract requirements. The QEI will be
directly employed by the Contractor and independent of the elevator
contractor.
Upon completion, the QEI must provide written test data for all
ASME A17.1/CSA B44 Acceptance Tests and written certification that the
elevator is complete and ready for final Acceptance Inspection, Testing,
and Commissioning.
3.3 ACCEPTANCE INSPECTION, TESTING AND COMMISSIONING
When elevator system installation is complete and ready for final
inspection, notify Contracting Officer that elevator system is ready for
Acceptance Inspection, Testing, and Commissioning. Provide QEI
certification specified in Article FIELD QUALITY CONTROL.
Contracting Officer will obtain the services of a third-party QEI Certified
Elevator Inspector. The QEI must utilize an Elevator Acceptance Inspection
Form to record the results of inspection and all testing and to identify
safety code and contract deficiencies. Specific values must be provided
for all tests required by ASME A17.1/CSA B44, ASME A17.2, and contract
documents. Upon completion of inspection and testing, the QEI must sign a
copy of the completed forms and provide to the Contracting Officer. Within
2 weeks of the inspection, the QEI must also prepare a formal inspection
report, including all test results and deficiencies. Upon successful
completion of inspection and testing, the QEI will complete, sign, and
provide a certificate of compliance with ASME A17.1/CSA B44.
3.3.1 Acceptance Inspection Support
Prime and Elevator Contractors must provide inspection support and perform
all required tests, in order to demonstrate proper operation of each
elevator system and to prove that each system complies with contract
requirements and all applicable building and safety codes. Inspection
procedures in ASME A17.2 form a part of this inspection and acceptance
testing. All inspection and testing must be conducted in the presence of
the Qualified Elevator Inspector (QEI).
If the elevator does not comply with all contract and safety code
requirements on the initial Acceptance Inspection and Test, the Contractor
is responsible for all costs involved with re-inspection and re-testing
required as a result of contractor delays and discrepancies discovered
during inspection and testing.
SECTION 14 24 23 Page 18
Bldg 615 FSH19B615
3.3.2 Testing Materials and Instruments
Furnish all testing materials and instruments necessary for Acceptance
Inspection, Testing and Commissioning. At a minimum, include calibrated
test weights, tachometer, accelerometer, hydraulic pressure gauge, 600-volt
mega ohm meter, volt meter and ammeter, infrared temperature gauge, door
pressure gage, dynamometer, and 20 foot tape measure.
3.3.3 Field Tests
3.3.3.1 Endurance Tests
Test each elevator for a period of one hour continuous, automatic
operation, with specified rated load in the elevator cab. During the one
hour test, stop car at each floor, in both directions of travel, and allow
automatic door open and close operation. The requirements for Automatic
Operation, Rated Speed, Leveling, Temperature Rise and Motor Amperes must
be met throughout the duration of the Endurance Test. Restart the one hour
test period from the beginning, following any shutdown or failure.
3.3.3.2 Speed Tests
Determine actual speed of each elevator, in both directions of travel, with
rated load and with no load in elevator car. Make Speed tests at the
beginning and at the end of the Endurance test. Determine speed by
tachometer reading or accelerometer, excluding accelerating and slow-down
zones. Under all conditions, minimum acceptable elevator speed is the
Rated speed specified. Maximum acceptable elevator speed is 110 percent of
Rated speed.
3.3.3.3 Leveling Tests
Test elevator car leveling operation and provide a leveling accuracy equal
to or less than 1/8 inch at each floor with no load in car, and with rated
load in car, in both directions of travel. Determine leveling accuracy at
the beginning and at the end of the endurance tests.
3.3.3.4 Temperature Rise Tests
Determine temperature rise of elevator pump motor and hydraulic fluid
during one-hour full-load test run. Under these conditions, maximum
temperature rise must not exceed acceptable temperature rise indicated on
manufacturer's data plate. Start test only when equipment is within 5
degrees C of ambient temperature.
3.3.3.5 Motor Ampere Tests
At beginning and end of Endurance test, measure and record motor amperage
in both directions of travel and in both no-load and rated load conditions.
3.3.3.6 Elevator Performance and Ride Quality Testing
Evaluate elevator performance to ensure compliance with specification
requirements related to the NEII-1 Performance Standards Matrix for New
Elevator Installations.
3.3.3.7 Hydraulic Safety Valve (Automatic Shutoff Valve) Tests
In order to ensure consistent performance, regardless of hydraulic oil
SECTION 14 24 23 Page 19
Bldg 615 FSH19B615
temperature, test the Hydraulic Safety Valve twice. Test once before the
one-hour endurance test and once immediately after the one-hour test. For
elevator certification, safety valve must perform to code in both tests.
3.3.3.8 Hydraulic Pressure Tests
Check the hydraulic static pressure and rated-speed operating pressure at
the hydraulic control valve, under both no load and rated load conditions.
3.3.3.9
-- End of Section --
SECTION 14 24 23 Page 20