INDEX

SOLID TANTALUM CHIP CAPACITORS

PAGE
GENERAL PERFORMANCE CHARACTERISTICS..................................................................................................3-14
T491 SERIES — INDUSTRIAL GRADE .................................................................................................................15-19
T492 SERIES — CWR11 STYLE PER MIL-PRF-55365/8.....................................................................................20-21
T493 SERIES — MILITARY COTS ........................................................................................................................22-26
T494 SERIES — LOW ESR, INDUSTRIAL GRADE ...............................................................................................27-30
T495 SERIES — LOW ESR, SURGE ROBUST .....................................................................................................31-34
T496 SERIES — FAIL-SAFE WITH BUILT-IN FUSE .............................................................................................35-36
T510 SERIES — ULTRA-LOW ESR ......................................................................................................................37-39

POLYMER TANTALUM CHIP CAPACITORS

PAGE
GENERAL PERFORMANCE CHARACTERISTICS................................................................................................40-45
T520 SERIES — KO-CAP POLYMER ...................................................................................................................46-48
T525 SERIES — KO-CAP POLYMER - HIGH TEMPERATURE............................................................................49-50
T530 SERIES — KO-CAP POLYMER - MULTIPLE ANODE .................................................................................51-52

CERAMIC CHIP CAPACITORS

PAGE
GENERAL PERFORMANCE CHARACTERISTICS................................................................................................53-57
CERAMIC CHIP-STANDARD ................................................................................................................................58-63
LAND DIMENSIONS ...................................................................................................................................................62
THICKNESS CODE REEL QUANTITY REFERENCE CHART.....................................................................................63
CERAMIC OPEN-MODE........................................................................................................................................64-65
CERAMIC HIGH VOLTAGE ...................................................................................................................................66-69
CERAMIC CAPACITOR ARRAY ............................................................................................................................70-71
MIL-PRF-55681 ESTABLISHED RELIABILITY ......................................................................................................72-76
MIL-PRF-55681 TAPE AND REEL QUANTITIES ........................................................................................................76
Mil-PRF-123 and GR900 high-reliability ceramic chips are also available. Refer to KEMET Catalog F-3054 for
detailed information.

TANTALUM & CERAMIC CHIP PACKAGING

PAGE
TANTALUM CHIP PACKAGING INFORMATION .............................................................................................77,79-80
CERAMIC CHIP PACKAGING INFORMATION .....................................................................................................78-82
EMBOSSED CARRIER TAPE REELING INFORMATION............................................................................................80
PUNCHED CARRIER TAPE (PAPER TAPE) REELING INFORMATION .....................................................................81
BULK CASSETTE PACKAGING .................................................................................................................................82
CERAMIC CHIP MARKING.........................................................................................................................................82

Notice
Although the information in this catalog has been carefully checked for accuracy, and is believed to be cor-
rect and current, no warranty, either express or implied, is made as to either its applicability to, or its com-
patibility with, specific requirements; nor does KEMET Electronics Corporation assume any responsibility
for correctness of this information, nor for damages consequent to its use. All design characteristics, speci-
fications, tolerances, and the like are subject to change without notice.

The KEMET website (www.kemet.com) should be consulted for the very latest information on design char-
acteristics, specifications, applications, and newly-released products, since previously-issued printed infor-
mation may not be current.

Any capacitors misapplied may fail and thereby damage other circuit components. Please refer to applica-
tion notes and recommendations in this catalog for a complete description of capacitor characteristics.

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 TANTALUM CHIP CAPACITORS
PRODUCT DESCRIPTION
KEMET’s family of solid tantalum chip capacitors is T493 Series — Military - COTS
designed and manufactured with the demanding The T493 series is designed for the COTS
requirements of surface mount technology in mind. (Commercial-Off-The-Shelf) requirements of
These devices extend the advantages of solid tan- military/aerospace applications. This series is a sur-
talum technology to today’s surface mount circuit face mount tantalum product offering various lead-
applications. Complementing multilayer ceramic chip frame surface finishes, Weibull grading and surge cur-
convenience with capacitance ratings through 1500 rent testing options. The full part number includes a
µF, tantalum chip capacitors permit circuit designers code defining the terminations, the Weibull reliability,
to take full advantage of the benefits of surface mount surge test conditions, and the ESR range. The possi-
technology. ble terminations include gold plated, hot solder
dipped, solder plated, and solder fused. Reliability
grading of B level (0.1%/kHours) and C level
T491 Series — Industrial (0.01%/kHours) are available. Surge current testing
The leading choice in today’s surface mount options include: 10 cycles at 25ºC, or 10-cycles at -
designs is the KEMET T491 Series. This product 55ºC and +85ºC. Both standard and low ESR options
meets or exceeds the requirements of EIA standard are available. All lots of this series are conditioned with
535BAAC. The physical outline and dimensions of MIL-PRF-55365 Group A testing.
this series conform to this global standard.
Five low profile case sizes have been added to the
T494 Series — Low ESR, Industrial Grade
T491 family. The R/2012-12, S/3216-12 and T/3528-
The T494 is a low ESR series that is available in all
12 case sizes have a maximum height of 1.2 mm. The
the same case sizes and CV ratings as the popular
U/6032-15 size has a maximum height of 1.5 mm,
T491 series. The T494 offers low ESR performance
and the V/7343-20 has a maximum height of 2.0 mm.
with the economy of an industrial grade device. This
This product was designed specifically for today’s series is targeted for output filtering and other applica-
highly automated surface mount processes and equip- tions that may benefit from improved efficiency due to
ment. This series uses the same proven solid tanta- low ESR.
lum KEMET technology acclaimed and respected
throughout the world. Added to this is the latest in
materials, processes and automation which result in a T495 Series — Low ESR, Surge Robust
component unsurpassed worldwide in total perfor- The low ESR, surge robust T495 series is an impor-
mance and value. tant member of KEMET’s tantalum chip family.
The standard terminations are 100% matte tin and Designed primarily for output filtering in switch-mode
provide excellent wetting characteristics and compatibil- power supplies and DC-to-DC converters, the standard
ity with today’s surface mount solder systems. Tin-Lead CV T495 values are also an excellent choice for battery-
(SnPb) terminations are available upon request for any to-ground input filter applications.
part number. Gold-plated terminations are also available This series builds upon proven technology used for
for use with conductive epoxy attachment processes. industrial grade tantalum chip capacitors to offer sev-
The symmetrical terminations offer total compliancy to eral important advantages: very low ESR, high ripple
provide the thermal and mechanical stress relief current capability, excellent capacitance stability, plus
required in today’s technology. Lead frame attachments improved ability to withstand high inrush currents.
to the tantalum pellet are made via a microprocessor- These benefits are achieved through a combination of
controlled welding operation, and a high temperature proprietary design, material, and process parameters,
silver epoxy adhesive system. as well as high-stress, low impedance electrical con-
Standard packaging of these devices is tape and ditioning performed prior to screening. Capacitance
reel in accordance with EIA 481-1. This system pro- values range from 4.7µF to 1000µF, in voltage ratings
vides perfect compatibility with all tape-fed from 4 to 50.
placement units.
T496 Series — Fused
T492 Series — Military KEMET also offers a “fail-safe” fused solid tantalum
KEMET is approved to MIL-PRF-55365/8 chip capacitor. The built-in fuse element provides
(CWR11), Weibull failure rate “B” level or 0.1% fail- excellent protection from damaging short circuit condi-
ures per 1,000 hours, “C” level or 0.01% failures per tions in applications where high fault currents exist.
1,000 hours, and “D” level or 0.001% failures per Protection from costly circuit damage due to reversed
1,000 hours. This CWR11 product — designated as installation is offered with this device. Package sizes
KEMET’s T492 Series — is a precision-molded include the EIA standard 3528-12, 6032-15, 7343-31,
device, with compliant leadframe terminations and and 7343-43 case size. Capacitance values range from
indelible laser marking. This is the military version of 0.15 µF to 470.0 µF, in voltage ratings from 4 to 50.
the global IEC/EIA standard represented by Standard capacitance tolerances include ±20% and
KEMET’s T491 Series. Tape and reeling per EIA ±10%. Tape and reeling per EIA 481-1 is standard.
481-1 is standard.
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 3
 TANTALUM CHIP CAPACITORS
PRODUCT DESCRIPTION
T510 Series — Ultra–Low ESR T525 SERIES — High Temperature Organic Polymer
The ultra-low ESR T510 Series is a breakthrough in The T525 Series is a version of KEMET’s Tantalum
solid tantalum capacitor technology. KEMET’s T510 Polymer Capacitor rated up to 125ºC. This part type
Series offers the low ESR in the popular EIA 7343-43 was introduced as Lead (Pb) Free and offers the
and 7360-38 case sizes. The ultra-low ESR and high same advantages as to KO-CAP. This includes low
ripple current capability make the T510 an ideal ESR, high frequency capacitance retention and
choice for SMPS filtering and power decoupling of benign failure mode.
today’s high speed microprocessors.
KEMET has developed an innovative construction T530 SERIES — Organic Polymer Multiple Anode
platform that incorporates multiple capacitor elements, KEMET is offering a multiple anode tantalum chip
in parallel, inside a single package. This unique capacitor with a polymer material replacing the MnO2
assembly, combined with KEMET’s superior process- offering non-ignition, self-healing, 125C performance
ing technology, provides the best combination of high capability with higher conductivity material that low-
CV, low ESR, and small size in a user friendly, molded, ers the ESR. Packaged as multiple anodes to reduce
surface mount package. the depth that the signal must penetrate, this parallel
arrangement reduces the ESR further still to achieve
T520 SERIES — Organic Polymer Tantalum the highest capacitance and lowest ESR of any other
The KO-CAP is a Tantalum capacitor, with Ta type of SMT capacitor with typical ESR of 7 mil-
anode and Ta2O5 dielectric. However, a conductive, liohms. With the reduced ESR, the enhanced capaci-
organic, polymer replaces the MnO2 as the cathode tance retention in higher frequencies results in the
plate of the capacitor. This results in very low ESR lowest total capacitance solution and provides for the
and improved cap retention at high frequency. The most economical solution in high power applications.
KO-CAP also exhibits a benign failure mode, which
eliminates the ignition failures that can occur in stan-
dard MnO2 Tantalum types. Note also that KO-CAPs
may be operated at voltages up to 90% of rated
voltage for part types with rated voltage ≤ 10 volts
and up to 80% of rated voltage for part types > 10
volts with equivalent or better reliability than stan-
dard tantalums operated at 50% of
rated voltage.
The T520 series captures the best features of mul-
tilayer ceramic caps (low ESR and high frequency
cap retention), aluminum electrolytics (benign failure
mode), and proven solid tantalum technology (volu-
metric efficiency, surface mount capability, and no
wearout mechanism). The KO-CAP can reduce
component counts, eliminate through-hole assem-
bly by replacing cumbersome leaded aluminum
capacitors, and offer a more cost effective solution
to high-cost high-cap ceramic capacitors. These
benefits allow the designer to save both board
space and money. See pages 40-45 for complete
details.

4 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 SOLID TANTALUM CHIP CAPACITORS
TANTALUM MnO2 COMPONENT PERFORMANCE CHARACTERISTICS
Introduction of equilibrium with the environment, is approxi-
KEMET solid tantalum capacitors are identified by mately -5% to +12% over the range from 25% to
the initial “T,” followed by a unique “Series” num- 95% RH, referred to the standard 50% RH. The
ber; for example, T491, T492, etc. Each Series amount of change is dependent upon size (capaci-
denotes a general physical form and type of tance and voltage rating, ie: CV product); small
encapsulation, as well as limits on dimensions and sizes might change no more than ±5%.
certain electrical characteristics under standard Equilibrium at such extremes is seldom attained by
conditions of 25°C, 50% relative humidity, and one plastic-cased capacitors, and the change in

Solid Tantalum Surface Mount

atmosphere pressure. Specific requirements are capacitance is consequently less. The rate of
set forth in the respective Product Series in this response to humidity changes increases with
catalog. All series are 100% screened for leakage, increasing temperature. Dissipation factor and
capacitance, dissipation factor, and ESR. All ESR also increase with increasing RH.
Series are inspected to electrical limits using a DC leakage current may rise upon exposure to a
minimum .1% AQL sampling plan, according to combination of high temperature and high humidi-
the Military Standard MIL-STD-105, even after ty, but is normally restored by voltage conditioning
100% testing. This sampling plan, to the best of under standard conditions. The increase will be
KEMET Electronics’ knowledge, meets or exceeds greater than that experienced under temperature
the generally accepted industry standard for simi- influence alone because of conduction through
lar products. KEMET capacitors may also be sup- absorbed water.
plied, with prior agreement, to meet specifications
Tantalum chips may be affected by absorption of
with requirements differing from those of KEMET cat-
water on external insulating surfaces.The water
alogs.
film may also attract a layer of dust from the air,
increasing the effect. The most sensitive parame-
ELECTRICAL ter is leakage current.
1. General Application Class 4. Capacitance
Solid tantalum capacitors are usually applied in • 0.1 µF to 1000 µF
circuits where the AC component is small com- Refer to part number tables for available capaci-
pared to the DC component. Typical uses known tance ratings and tolerances by series.
to KEMET Electronics include blocking, by-pass-
Capacitance is measured at 120 Hz, up to 1.0
ing, decoupling, and filtering. They are also used in
volt rms maximum and up to 2.5 volts DC maximum, at
timing circuits. General purpose devices are rec-
+25°C.DC bias causes only a small reduction in capaci-
ommended to have an external series resistance of
tance, up to about 2% when full rated voltage is applied.
0.1Ω/volt to reduce the failure due to surge cur-
DC bias is not commonly used at room temperature, but
rent. Newer devices designed for power applica-
is more commonly used at elevated temperatures.
tions (T495, T5XX), are built to eliminate this series
Capacitance decreases with increasing frequency.
resistance requirement. Because tantalum capaci-
tors can experience scintillation (self-healing) in
their life, the circuit impedence should not exceed
100KΩ or this will circumvent the scintillation and
degrade leakage.
2. Operating Temperature Range
• –55 °C to +125 °C
Voltage derating is specified in Section 5.
Performance characteristics over this temperature
range are presented within the following sections.
FIGURE 1 Typical Effect of Frequency upon Capacitance
3. Non-Operating Temperature Range
Capacitance increases with increasing temperature.
• –55 °C to +125 °C
Tantalum capacitors do not lose capacitance from
the “de-forming” effect as do liquid-electrolytic +20%
Percent Change in +25⬚C

capacitors. Storage at high temperature may +10%

Capacitance Value

cause a small, temporary increase in leakage cur-

rent (measured under standard conditions), but the 0

original value is usually restored within a few min-

-10%
utes after application of rated voltage.
Tantalum chips are not hermetically sealed, there- -20%

fore they do exhibit reversible changes in parame-

ters with respect to relative humidity (RH). -80 -60 -40 -20 0 +20 +40 +60 +80 +100 +120
Operating Temperature—⬚C
Capacitance increases with increasing humidity.
The limiting change, reached upon establishment FIGURE 2 Typical Effect of Temperature upon Capacitance

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 5
 SOLID TANTALUM CHIP CAPACITORS

TANTALUM MnO2 COMPONENT PERFORMANCE CHARACTERISTICS (con’t.)

TABLE 1 Maximum Capacitance Change conditions, including the sum of peak AC ripple,
with Temperature (ref: 25°C) DC bias and any transients.
Ambient Temperature Surge voltage tests are performed at +25°C,
+85°C and +125°C with the applicable surge volt-
–55°C +85°C +125°C
age. The surge voltage is applied for 1000 cycles
–10% +10% *+12% or +15%to20% of 30 seconds at voltage through a 33 ohm series
resistor and 30 seconds off voltage with the
*+12% is standard. +15% and 20% apply to certain capacitor discharged through a 33 ohm resistor.
extended CV values as noted in part number tables.
Upon completing the test, the capacitors are
5. Working DC Voltage (WVDC) allowed to stabilize at room temperature. Capaci-
• 3 to 50 volts tance, DCL and DF are then tested:
Refer to part number tables for available voltage a. Capacitance — within ± 5% of initial value
ratings by series. b. DC Leakage — within initial limit
These voltages are the maximum recommended peak c. Dissipation Factor — within initial limit
DC operating voltages from –55°C to +85°C for d. ESR — within initial limit
continuous duty. These voltages are derated linearly above
7. Reverse Voltage and Polarity
+85°C to 2/3 rated voltage for operation at
+125°C (See Figure 3). For added reliability it is TABLE 3 Reverse Voltage Ratings
recommended to operate at a 50% derating of the working Temperature Permissible Reverse Voltage
voltage for tantalum capacitors with MnO2 as a cathode. +25°C 15% of Rated Voltage
+85°C 5% of Rated Voltage
+125°C 1% of Rated Voltage
100%
Working DC Voltage

Solid tantalum capacitors are polarized devices

Percent Change in

80%
and may be permanently damaged or destroyed if
60% connected with the wrong polarity. The positive
40%
terminal is identified on the capacitor body by a
stripe and a beveled edge. A small degree of tran-
20% sient reverse voltage is permissible for short peri-
ods per Table 3. The capacitors should not be
-60 -40 -20 0 +20 +40 +60 +80 +100 +120 +140 operated continuously in reverse mode, even with-
Operating Temperature—⬚C
in these limits.
FIGURE 3 Working DC Voltage Change with Temperature
8. DC Leakage Current (DCL)
6. Surge Voltage Refer to part number tables for maximum leakage
current limits.
TABLE 2 Surge Voltage Ratings DC leakage current is the current that, after a one-
at +25°C, +85°C & +125°C to five-minute charging period, flows through a
Rated capacitor when voltage is applied. Leakage is
Working Surge Derated measured at +25°C with full rated DC voltage
Volts Voltage DC Surge applied to the capacitor through a 1000 ohm resis-
@ +25°C @ +25°C Volts Voltage tor in series with the capacitor.
& +85°C & +85°C @ +125°C @ +125°C DC leakage current increases with increasing tem-
3 4 2 2.4 perature.
4 5.2 2.7 3.2
6 8 4 5 TABLE 4 Leakage Limit Multipliers at Specified
10 13 7 8 Temperatures (ref: 25°C limits)
16 20 10 12 Ambient Temperature
20 26 13 16
–55°C +85°C +125°C
25 33 17 20 N/A 10X 12X
35 46 23 28
50 65 33 40
Surge voltage is the maximum voltage to which
the capacitor can be subjected under transient
6 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 SOLID TANTALUM CHIP CAPACITORS

TANTALUM MnO2 COMPONENT PERFORMANCE CHARACTERISTICS (con’t.)

20.0

Multiplier of 120 Hz D.F.

10.0
10.0
Multiplier of DC Leakage Current

5.0

Solid Tantalum Surface Mount

Reference 1.0 Reference
at + 25°C 1.0 at 120 Hz

1.0
1.0
100 1k 10k
Frequency — Hertz

FIGURE 6 Typical Effect of Frequency upon Dissipation

Factor
Dissipation factor is a very useful low frequency
(120 Hz) measurement of the resistive component
0.1 of a capacitor. It is the ratio of the equivalent series
-60 -40 -20 0 +20 +40 +60 +80 +100 +125
resistance (ESR) to the capacitive reactance, (XC)
Operating Temperature—⬚C
and is usually expressed as a percentage. It is
FIGURE 4 Typical Effect of Temperature upon directly proportional to both capacitance and fre-
DC Leakage Current quency. Dissipation factor loses its importance at
higher frequencies, (above about 1 kHz), where
DC leakage current decreases with decreasing impedance (Z) and equivalent series resistance
applied voltage. (ESR) are the normal parameters of concern.
DF = R = 2fCR DF = Dissipation Factor
1.0 XC R = Equivalent Series
Resistance (Ohms)
X C = Capacitive Reactance
Multiplier of DC Leakage Current

(Ohms)
0.1 f = Frequency (Hertz)
C = Series Capacitance
(Farads)

0.01 DF is also referred to as tan  or “loss tangent.”

The “Quality Factor,” “Q,” is the reciprocal of DF.
DF decreases with temperature above +25°C and
may also increase at lower temperatures.
0.001 Unfortunately, one general limit for DF cannot be
0 10 20 30 40 50 60 70 80 90 100 110 specified for all capacitance/voltage combinations,
Percentage of Rated Voltage nor can response to temperature be simply stated.
FIGURE 5 Typical Effect of Applied Voltage on DC DC bias is not commonly used at room tempera-
Leakage Current. ture, but is more commonly used at elevated tem-
peratures.
9. Dissipation Factor (DF)
Refer to part number tables for maximum DF 10. Equivalent Series Resistance (ESR) and
limits. Impedance (Z)
Equivalent Series Resistance (ESR) is the pre-
Dissipation factor is measured at 120 Hz, up to ferred high-frequency statement of the resistance
1.0 volt rms maximum, and up to 2.0 volts DC unavoidably appearing in these capacitors. ESR
maximum at +25°C. The application of DC bias is not a pure resistance, and it decreases with
causes a small reduction in DF, about 0.2% when increasing frequency.
full rated voltage is applied. DF increases with Total impedance of the capacitor is the vector
increasing frequency. sum of capacitive reactance (XC) and ESR, below
resonance; above resonance total impedance is
the vector sum of inductive reactance (XL) and
ESR.
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 7
 SOLID TANTALUM CHIP CAPACITORS
TANTALUM MnO2 COMPONENT PERFORMANCE CHARACTERISTICS (con’t.)
RS — Represents the actual ohmic series resis-
tance in series with the capacitance. Lead wires
and capacitor electrodes are contributing sources.
RL — Capacitor Leakage Resistance. Typically it
can reach 50,000 megohms in a tantalum capaci-
tor. It can exceed 1012 ohms in monolithic ceram-
XC = 1 ohm ics and in film capacitors.
2fC Rd — The dielectric loss contributed by dielectric
absorption and molecular polarization. It becomes
where: very significant in high frequency measurements
f = frequency, Hertz
and applications. Its value varies with frequency.
C = capacitance, Farad
Cd — The inherent dielectric absorption of the
solid tantalum capacitor which typically equates to
FIGURE 7a Total Impedance of the Capacitor Below 1-2% of the applied voltage.
Resonance
As frequency increases, XC continues to decrease
according to its equation above. There is unavoid-
able inductance as well as resistance in all capaci-
tors, and at some point in frequency, the reac-
tance ceases to be capacitive and becomes
inductive. This frequency is called the self-reso-
nant point. In solid tantalum capacitors, the reso-
XL = 2fL nance is damped by the ESR, and a smooth,
rather than abrupt, transition from capacitive to
where: inductive reactance follows.
f = frequency, Hertz
L = inductance, Henries Typical ESR/Z frequency response curves are
shown in Figures 9a and 9b. These curves are
for selected ratings and represent typical T491
Series performance. Maximum limits for 100 kHz
ESR are listed in the part number tables for
each series. Note that the T494 Series offers low
FIGURE 7b Total Impedance of the Capacitor Above ESR and the T495 Series is specially designed
Resonance for very low ESR performance. Refer to pages 27
To understand the many elements of a capaci- and 31 for more information. See also KEMET’s
tor, see Figure 8. T510 Series low ESR ratings on page 37.

L RS C

RL

Cd Rd

FIGURE 8 The Real Capacitor

A capacitor is a complex impedance consisting of

many series and parallel elements, each adding
to the complexity of the measurement system.
L — Represents lead wire and construction
inductance. In most instances (especially in solid FIGURE 9a ESR & Impedance (Z) vs Frequency
tantalum and monolithic ceramic capacitors) it is
insignificant at the basic measurement frequen-
cies of 120 and 1000 Hz.
8 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 SOLID TANTALUM CHIP CAPACITORS
TANTALUM MnO2 COMPONENT PERFORMANCE CHARACTERISTICS (con’t.)
12. AC Operation
Permissible AC ripple voltage and current are
related to equivalent series resistance (ESR) and
power dissipation capability.
Permissible AC ripple voltage which may be
applied is limited by three criteria:

Solid Tantalum Surface Mount

a. The positive peak AC voltage plus the DC
bias voltage, if any, must not exceed the DC
voltage rating of the capacitor.
b. The negative peak AC voltage, in combination
with the bias voltage, if any, must not exceed
FIGURE 9b ESR & Impedance (z) vs Frequency the permissible reverse voltage ratings pre-
ESR and Z are also affected by temperature. At sented in Table 3.
100 kHz, ESR decreases with increasing temper- c. The power dissipated in the ESR of the capa-
ature. The amount of change is influenced by the citor must not exceed the appropriate value
size of the capacitor and is generally more pro- specified in Table 5.
nounced on smaller ratings. Actual power dissipated may be calculated from
the following:
Multiplier of 100KHz ESR
10 P =l R 2

Substituting I = E , P = E2R
Z Z2
where:
1 I = rms ripple current (amperes)
E = rms ripple voltage (volts)
P = power (watts)
Z = impedance at specified frequency (ohms)
0.1 R = equivalent series resistance at specified
-50 -25 0 25 50 75 100 125 frequency (ohms)
Temperature - Degrees Centigrade Using P max from Table 5, maximum allowable
FIGURE 10 Typical Effect of Temperature on 100 kHz ESR rms ripple current or voltage may be determined
as follows:
11. AC Power Dissipation I (max) = P max/R E (max) = Z P max/R
Power dissipation is a function of capacitor size These values should be derated at elevated tem-
and materials. Maximum power ratings have been peratures as follows:
established for all case sizes to prevent overheat- Temperature Derating Factor
ing. In actual use, the capacitor’s ability to dissi- 85C .9
pate the heat generated at any given power level 125C .4
may be affected by a variety of circuit factors.
These include board density, pad size, heat sinks ENVIRONMENTAL
and air circulation. 13. Temperature Stability
TABLE 5 Tantalum Chip Power Dissipation Ratings TABLE 6 Temperature Stability Limits
Case Code Maximum Power Dissipation Step Leakage Dissipation
No. Temp.  Capacitance Current Factor
KEMET EIA mW @ +25°C w/+20°C Rise
1 +25C within specified within original within original
R 2012-12 25 tolerance limit limit
S 3216-12 60 2 -55C within ± 10% N/A within original
T 3528-12 70 of initial value limit**
U 6032-15 90 3 +25C within ± 5% within original within original
V 7343-20 125 of initial value limit limit**
4 + 85C within ± 10% within 10X within original
A 3216-18 75
of initial value original limit limit***
B 3528-21 85 5 +125C *within ± 12%or within 12X within original
C 3062-28 110 20% of initial original limit limit***
D 7343-31 150 value
X 7343-43 165 6 +25C within ± 5% within original within original
E 7260-38 200 of initial value limit limit
T530D 7343-31 255 *+12% is standard. +15% or +20% applies to certain CV values
T510X, T530X 7343-43 270 as noted in part number table.
T510E, T530E 7260-38 285 **within 1.5x initial limit for extended CV values.
***within 1.15x initial limit for extended CV values.
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 9
 SOLID TANTALUM CHIP CAPACITORS

TANTALUM MnO2 COMPONENT PERFORMANCE CHARACTERISTICS (con’t.)

Mounted capacitors withstand extreme temperature The same comparative change has been
testing at a succession of continuous steps at observed in shelf tests at +25°C extending for
+25°C, -55°C, +25°C, +85°C, +125°C, +25°C, in the 50,000 hours. (Some of this change may stem
order stated. Capacitors shall be brought to thermal from instrument or fixture error.)
stability at each test temperature. Capacitance, DF Dissipation factor exhibits no typical trend. Data
and DCL are measured at each test temperature from 10,000 hour life test at +85°C show that ini-
except that DCL is not measured at -55°C. DC bias tial limits (at standard conditions) are not exceeded
of 2.0± 0.5 is recommended for the capacitance at the conclusion of these tests.
and D F requirements.
Leakage current is more variable than capaci-
14. Thermal Shock tance or DF; in fact, leakage current typically
• Mil-Std-202, Method 107, Condition B exhibits a logarithmic dependence in several
Minimum temperature -55°C, mounted respects. Military Specifications permit leakage
Post Test Performance: current (measured at standard conditions) to rise
by a factor of four over 10,000 hour life tests.
a. Capacitance — within ±5% of initial value Typical behavior shows a lower rate of change,
b. DC Leakage — within initial limit which may be negative or positive. Initial leakage
c. Dissipation Factor — within initial limit currents are frequently so low (less than 0.1
d. ESR — within initial limit nanoampere in the smallest CV capacitors) that
changes of several orders of magnitude have no
15. Moisture Resistance discernable effect on the usual circuit designs.
• Mil-Std-202, Method 106
18. Failure Mode
Steps 7a and 7b excluded, rated voltage, Capacitor failure may be induced by exceeding
42 cycles, mounted 50% of rated voltage of the capacitor with forward
Post Test Performance: DC voltage, reverse DC voltage, power dissipation,
a. Capacitance — within ±10% of initial value or temperature. As with any practical device, these
b. DC Leakage — within initial limit capacitors also possess an inherent, although low,
failure rate when operated at less than 50% of the
c. Dissipation Factor — within initial limit
rated voltage of the capacitor.
d. ESR — within initial limit
The dominant failure mode is by short-circuit.
16. Electrostatic Discharge (ESD) Minor parametric drifts are of no consequence in
• Human Body Model circuits suitable for solid tantalum capacitors.
2,000 ±50 volts, 1,500 ±5% ohms, 40 nano- Catastrophic failure occurs as an avalanche in DC
second pulse each polarity, 1 pulse each leakage current over a short (millisecond) time
polarity, 5 seconds between pulses, +25C. span. The failed capacitor, while called “short-cir-
• Charged Device Model cuited”, may exhibit a DC resistance of 10 to 104
200 ± 5 volts, 0 ohms, 40 nanosecond ohm.
pulse, each polarity, 9 pulses each polarity, If a failed capacitor is in an unprotected low-
5 seconds between pulses, +25C. impedance circuit, continued flow of current
Product subjected to above test condition through the capacitor may obviously produce
demonstrate no sensitivity to electrostatic severe overheating. The over-heated capacitor
discharge. may damage the circuit board or nearby compo-
17. Long Term Stability nents. Protection against such occurrence is
Within the general class of electrolytic capacitors, obtained by current-limiting devices or fuses pro-
solid tantalum capacitors offer unusual stability of vided by the circuit design. KEMET’s T496 series
the three important parameters: capacitance, dis- offers a built-in fuse to convert the normal short
sipation factor and leakage current. These solid- circuit failure mode to an open circuit.
state devices are not subject to the effects of Fortunately, the inherent failure rate of KEMET
electrolysis, deforming or drying-out associated solid tantalum capacitors is low, and this failure
with liquid-electrolyte capacitors. rate may be further improved by circuit design.
When stabilized for measurement at standard Statistical failure rates are provided for military
conditions, capacitance will typically change less capacitors. Relating circuit conditions to failure
than ±3% during a 10,000 hour life test +85°C. rate is aided by the guides in the section following.

10 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 SOLID TANTALUM CHIP CAPACITORS

TANTALUM MnO2 COMPONENT PERFORMANCE CHARACTERISTICS (con’t.)

RELIABILITY (1) λV = λbπTπCπVπSRπQπE x 1000

19. Reliability Prediction (2) λb = 0.00005CWR or 0.0004CSR

Solid tantalum capacitors exhibit no degradation
failure mode during shelf storage and show a (3) πT = exp [
-0.15
( 1
8.617 • 10-5 TAmb 298
1
)]
constantly decreasing failure rate (i.e., absence

Solid Tantalum Surface Mount

of any wear out mechanism) during life tests. Application-Voltage
( )
17
(4) S=
Rated-Voltage πV = S +1
This failure rate is dependent upon three impor- 0.6
tant application conditions; DC Voltage, ambient
temperature, and circuit impedance. Additional (5) πC = 1.0 • C.023
effects are attributable to the capacitance of the
(6) πSR = Lookup Table πE = Lookup Table
device and atmospheric and mechanical expo-
sure of the assembled circuit. The 1000 multiplier
at the end converts the failure rate to parts-per-
(7) ( Pcs. Fail
πQ = Pcs. Tested x Hrs. Tested x 100,000 )
billion piece-hours. A prediction of the failure rate
FIGURE 11a. MIL-HDBK-217F Notice 2 formulas.
can be made using these application conditions
and the formulas and tables listed in MIL-HDBK-
217F (Notice 2).
Base Multiplier: The first multiplier is the base CR (ΩV) πSR
multiplier (2) established for the capacitor type. >0.8 0.66
For “CWR-Chips” or surface mount components 0.6-0.8 1.0
the base multiplier is 0.00005, and for “CSR- 0.4-0.6 1.3
0.2-0.4 2.0
Leaded” devices, the base multiplier is 0.00040.
0.1-0.2 2.7
Temperature: The temperature factor is given as <0.1 3.3
(3). From this formula, it can be seen that the unity
factor, or 1, is derived at an ambient temperature FIGURE 11b. Table for circuit resistance multipiers.
of +25C (+298K), and that at temperatures
below this the multiplier is decreasing and at tem-
peratures above this the multiplier is increasing. Quality Factor: All of these multipliers are
Voltage: The multiplier for application voltage (4) applied to the established or base failure rate of
is a two step process: first, the application volt- the part. The T492 Series is qualified under U.S.
age is compared to 60% of rated voltage, and military specification MIL-PRF-55365. Failure
then this ratio is raised to an exponential power rates as low as 0.001% kHr are available under
of 17 and added to unity. Consider applications this test program.
of 50%, 60%, 70%, 80% and 90% of rated volt- For series not covered by military specifications,
age. The multipliers for these applications would an internal sampling program is operated by
be 1.045, 2.00, 14.7, 134, and 986, respectively. KEMET Quality Assurance whereby parts are put
From these results it is evident why manufactur- on life test at rated voltage for 2000 hours. The
ers recommend application voltages not to confidence level chosen for the reporting data is
exceed 50% rated voltages. 60%. (The cost of sampling each batch would be
Capacitance: There is a factor (5) applied to the prohibitive, and no claim is made to guarantee
capacitance (in µF) which effectively increases the failure rate of each batch.) With this testing
the failure rate for increasing capacitance and each new qualification test for new parts, the
(increases in effective area resulting in increases average failure rate for all commercial Series lies
in possible faults). between 0.1% and 1.0% per thousand-
Series Resistance: The series resistance is only piece-hours.
concerned with the resistance per application FIT Calculator
bias (ohms per volt) external to the capacitor, All of these factors are gathered into a Windows
and does not include the ESR as a factor. based software, available free from the KEMET
Environmental: The environmental factor is web site (www.kemet.com). The “FIT Calculator”
determined by the harshness of the ambient software does all the calculations and look-ups
conditions beyond temperature. An explanation based on information entered or selected by the
of these ratings is included in the MIL specifica- operator. A manual may also be downloaded
tion and are too extensive to be covered here. In from the same web page to explain the controls
most cases, this factor is set to ground benign or and displays The manual as well as a help
GB, with the resulting factor equal to “1”. screen also detail the environmental conditions.
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 11
 SOLID TANTALUM CHIP CAPACITORS

TANTALUM MnO2 COMPONENT PERFORMANCE CHARACTERISTICS (con’t.)

20. Surge Current MECHANICAL
All conventional reliability testing is conducted
under steady-state DC voltage. Experience indi- 24. Resistance to Solvents
cates that AC ripple, within the limits prescribed, • Mil-Std-202, Method 215
has little effect on failure rate. Heavy surge cur- Post Test Performance:
rents are possible in some applications, howev- a. Capacitance — within ±10% of initial value
er. Circuit impedance may be very low (below the b. DC Leakage — within initial limit
recommended 0.1 ohm/volt) or there may be dri- c. Dissipation Factor -— within initial limit
ving inductance to cause voltage “ringing.” Surge d. Physical — no degradation of case, termi-
current may appear during turn-on of equipment, nals or marking.
for example. Failure rate under current-surge
conditions may not be predictable from conven- 25. Fungus
tional life test data. • Mil-Std-810, Method 508
Capacitors are capable of withstanding a 4 ±1
second charge of rated voltage (±2%) through a 26. Flammability
total circuit resistance (excluding the capacitor) of • UL94 VO Classification
1 ±0.2 ohms at +25°C, followed by a 4 ±1 second Encapsulant materials meet this
discharge to a voltage below 1% of the rated volt- classification.
age. This cycle is repeated consecutively three 27. Resistance to Soldering Heat
(3) times. Post test performance:
• Wave Solder
a. Capacitance — within ±5% of initial value
b. DC Leakage — within initial limit +260 ±5 C, 10 Seconds
c. Dissipation Factor — within initial limit • Infrared Reflow
100% production surge current testing is per- +230 ±5 C, 30 Seconds
formed on all Tantalum Chip series for case sizes • Vapor Phase Reflow
C, D, E, X, U, V. The total test circuit resistance +215 ±5 C, 2 minutes
is ≤ 0.5 ohms. The applied voltage is 75% of Post Test Performance:
rated voltage for all series except the T495 and a. Capacitance — within ±10% of Initial Value
T510 which are surged at 100% of rated voltage. b. DC Leakage — within Initial Limit
Four surge cycles are applied. Parts not capable c. Dissipation Factor — within Initial Limit
of surviving this test are removed at subsequent
electrical screening. See T493 Series on page 22 28. Solderability
for specific surge options. • Mil-Std-202, Method 208
• ANSI/J-STD-002, Test B
21. Storage Life Test Applies to Solder and Tin Coated terminations
• 2,000 hours, +125 C, Unbiased, Mounted only. Does not apply to optional gold-plated ter-
Post Test Performance: minations.
a. Capacitance — within ±10% of initial value
b. DC Leakage — within initial limit 29. Vibration
c. Dissipation Factor — within initial limit • Mil-Std-202, Method 204, Condition D,
d. ESR — within initial limit 10 Hz to 2,000 Hz, 20G Peak
e. Physical — no degradation of function Post Test Performance:
a. Capacitance — within ± 10% of initial value
22. Standard Life Test b. DC Leakage — within initial limit
• 2,000 hours, +85 C, Rated Voltage, Mounted c. Dissipation Factor — within initial limit
Post Test Performance:
a. Capacitance — within ±10% of initial value 30. Shock
b. DC Leakage — within 125% of initial limit • Mil-Std-202, Method 213, Condition I,
c. Dissipation Factor — within initial limit 100 G Peak
d. ESR — within initial limit Post Test Performance:
e. Physical — no degradation of function a. Capacitance — within ±10% of initial value
b. DC Leakage — within initial limit
23. High Temperature Life Test c. Dissipation Factor — within initial limit
• 2,000 hours, +125 C, 2/3 Rated Voltage,
Mounted 31. Terminal Strength
Post Test Performance: • Pull Force
a. Capacitance — within ±10% of initial value • One Pound (454 grams), 30 Seconds
b. DC Leakage — within 125% of initial limit
c. Dissipation Factor — within initial limit
d. ESR — within initial limit
e. Physical — no degradation of function
12 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 SOLID TANTALUM CHIP CAPACITORS

TANTALUM MnO2 COMPONENT PERFORMANCE CHARACTERISTICS (con’t.)

• Tensile Force gold termination finish is available, at additional cost,
• Four Pounds (1.8 kilograms), 60 Seconds on the T491, T494 and T495 Series only.The gold
finish is not recommended for solder attachment.
Refer to specific lead frame options available on
T493 Series. Refer to www.kemet.com for details
on Pb free transition.

Solid Tantalum Surface Mount

34. Recommended Mounting Pad Geometries
Proper mounting pad geometries are essential
for successful solder connections. These dimen-
4 lb. (1.8 Kg) sions are highly process sensitive and should be
• Shear Force designed to maximize the integrity of the solder
Table 8 Maximum Shear Loads joint, and to minimize component rework due to
Case Code Maximum Shear Loads unacceptable solder joints.
KEMET EIA Kilograms Pounds Figure 12 illustrates pad geometry. Tables 9 &
R 2012-12 2.4 5.3 10 provide recommended pad dimensions for
S 3216-12 3.2 7.0 both wave and reflow soldering techniques.
T 3528-12 3.6 8.0 These dimensions are intended to be a starting
U 6032-15 4.5 10.0
point for circuit board designers, to
V 7343-20 5.0 11.0
be fine tuned, if necessary, based upon the pecu-
A 3216-18 3.2 7.0
B 3528-21 3.6 8.0
liarities of the soldering process and/or circuit
C 6032-28 4.5 10.0 board design.
D 7343-31 5.0 11.0 Contact KEMET for Engineering Bulletin Number
X 7343-43 5.0 11.0 F-2100 entitled “Surface Mount Mounting Pad
E 7260-38 5.0 11.0 Dimensions and Considerations” for further
details on this subject.

Grid
X Placement
Courtyard

Post Test Performance: G Y

a. Capacitance — within ±5% of initial value
b. DC Leakage — within initial limit Z
c. Dissipation Factor — within initial limit Figure 12

APPLICATIONS Table 9 – Land Pattern Dimensions for Reflow Solder

Pad Dimensions - mm
32. Handling KEMET/EIA Size Code Y C
Automatic handling of encapsulated components Z G X (ref) (ref)
is enhanced by the molded case which provides R/2012-12 3.90 0.80 1.80 1.55 2.35
compatibility with all types of high speed pick and A/3216-18, S/3216-12 4.70 0.80 1.50 1.95 2.75
B/3528-21, T/3528-12 5.00 1.10 2.50 1.95 3.05
place equipment. Manual handling of these C/6032-28, U/6032-15 7.60 2.50 2.50 2.55 5.05
devices presents no unique problems. Care D/7343-31, V/7343-20, X/7343-43 8.90 3.80 2.70 2.55 6.35
should be taken with your fingers, however, to E/7260-38 8.90 3.80 4.40 2.55 6.35
avoid touching the solder-coated terminations as Table 10 – Land Pattern Dimensions for Wave Solder
body oils, acids and salts will degrade the sol- Pad Dimensions - mm
derability of these terminations. Finger cots KEMET/EIA Size Code Y C
should be used whenever manually handling all Z G X (ref) (ref)
solderable surfaces. R/2012-12 4.30 0.80 1.26 1.75 2.55
A/3216-18, S/3216-12 5.10 0.80 1.10 2.15 2.95
33. Termination Coating B/3528-21, T/3528-12 5.40 1.10 1.80 2.15 3.25
After May 1, 2004, the standard finish coating for C/6032-28, U/6032-15 8.00 2.50 1.80 2.75 5.25
D/7343-31, V/7343-20, X/7343-43 9.70 3.80 2.70 2.95 6.75
all molded series is transitioning to 100% tin. E/7260-38 9.70 3.80 4.40 2.95 6.75
For conductive adhesive attachment processes, a
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 13
 SOLID TANTALUM CHIP CAPACITORS

TANTALUM MnO2 COMPONENT PERFORMANCE CHARACTERISTICS (con’t.)

35. Soldering During typical reflow operations a slight darken-
KEMET’s families of surface mount tantalum ing of the gold-colored epoxy may be observed.
capacitors are compatible with wave (single or This slight darkening is normal and is not harmful
dual) soldering and IR or vapor phase reflow to the product. Marking permanency is not affect-
techniques. Solder-coated terminations have ed by this change.
excellent wetting characteristics for high integrity
36. Washing
solder fillets. Preheating of these components is
Standard washing techniques and solvents are
recommended to avoid extreme thermal stress.
compatible with all KEMET surface mount tanta-
The maximum recommended preheat rate is 2°C
lum capacitors. Solvents such as Freon TMC and
per second. Figure 13 represents recommended
TMS, Trichlorethane, methylene chloride, prelete,
maximum solder temperature / time combinations
and isopropyl alcohol are not harmful to these
for these devices.
components.
Note that although the X/7343-43 case size can
If ultrasonic agitation is utilized in the cleaning
withstand wave soldering, the tall profile (4.3mm
process, care should be taken to minimize ener-
maximum) dictates care in wave process devel-
gy levels and exposure times to avoid damage to
opment.
the terminations.
Sn-Pb Profile KEMET tantalum chips are also compatible with
300
newer aqueous and semi-aqueous processes.
5 Sec.
250 Please follow the recommendations for cleaning
Temperature (°C)

200 as defined by the solder vendor.

150 37. Encapsulations
45 Sec. 45 Sec.
100 Under normal circumstances, potting or encap-
90 Sec. sulation of KEMET tantalum chips is not required.
50

0
95 Sec. 38. Storage Environment
0 50 100 150 200 250 300 Tantalum chip capacitors should be stored in
60 Sec. Time (Seconds) normal working environments. While the chips
themselves are quite robust in other environ-
ments, solderability will be degraded by expo-
Pb-Free Profile sure to high temperatures, high humidity, corro-
sive atmospheres, and long term storage. In
addition, packaging materials will be degraded
by high temperature – reels may soften or warp,
and tape peel force may increase. KEMET rec-
ommends that maximum storage temperature
not exceed 40 degrees C, and maximum storage
humidity not exceed 60% relative humidity. In
addition, temperature fluctuations should be
minimized to avoid condensation on the parts,
and atmospheres should be free of chlorine and
sulfur bearing compounds. For optimized solder-
FIGURE 13 Time/Temperature Soldering Profile ability, chip stock should be used promptly,
preferably within 3 years of receipt.
Hand-soldering should be performed with care
due to the difficulty in process control. If per-
formed, care should be taken to avoid contact of
the soldering iron to the molded case. The iron
should be used to heat the solder pad, applying
solder between the pad and the termination, until
reflow occurs. The iron should be removed.
“Wiping” the edges of a chip and heating the top
surface is not recommended.

14 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 SOLID TANTALUM CHIP CAPACITORS
T491 SERIES - Precision Molded Chip
FEATURES
• Meets or Exceeds EIA Standard 535BAAC • Tolerance: ±10%, ±20%
• Taped and Reeled per EIA 481-1 • Voltage: 3-50 VDC
• Symmetrical, Compliant Terminations • Extended Range Values
• Optional Gold-plated Terminations • Low Profile Case Sizes
• Laser-marked Case • RoHS Compliance
• 100% Surge current test on C, D, E, U, V, X sizes • Lead Free Terminations (See www.kemet.com for
• Halogen Free Epoxy transition information)
• Capacitance: 0.1 F to 1000 F
CAPACITOR OUTLINE DRAWING

Solid Tantalum Surface Mount

CATHODE (-) END SIDE VIEW ANODE (+) END BOTTOM VIEW
VIEW VIEW
B
W
B

H E F
K T P

S S R Termination A
X G cutout at L
KEMET’s
Option,
either end

STANDARD T491 DIMENSIONS

Millimeters (inches)
CASE SIZE COMPONENT
KEMET EIA L* W* H* K* ±± 0.20
(.008) F*
± 0.1 ± 0.3 B ± 0.15
± (.004) S* ± (.012) (Ref) ± (.006)
X
(Ref)
P R T A G E
(Ref) (Ref) (Ref) (Min) (Ref) (Ref)
A 3216-18 3.2 ± 0.2 1.6 ±0.2 1.6 ± 0.2 0.9 1.2 0.8 0.4 0.10 ± 0.10 0.4 0.4 0.13 0.8 1.1 1.3
(.126 ± .008) (.063 ±.008) (.063 ± .008) (.035) (.047) (.031) (.016) (.004 ± .004) (.016) (.016) (.005) (.031) (.043) (.051)
B 3528-21 3.5 ± 0.2 2.8 ± 0.2 1.9 ± 0.2 1.1 2.2 0.8 0.4 0.10 ± 0.10 0.5 1.0 0.13 1.1 1.8 2.2
(.138 ± .008) (.110 ± .008) (.075 ± .008) (.043) (.087) (.031) (.016) (.004 ± .004) (.020) (.039) (.005) (.043) (.071) (.087)
C 6032-28 6.0 ± 0.3 3.2 ± 0.3 2.5 ± 0.3 1.4 2.2 1.3 0.5 0.10 ± 0.10 0.9 1.0 0.13 2.5 2.8 2.4
(.236 ± .012) (.126 ± .012) (.098 ± .012) (.055) (.087) (.051) (.020) (.004 ± .004) (.035) (.039) (.005) (.098) (.110) (.094)
D 7343-31 7.3 ± 0.3 4.3 ± 0.3 2.8 ± 0.3 1.5 2.4 1.3 0.5 0.10 ± 0.10 0.9 1.0 0.13 3.8 3.5 3.5
(.287 ± .012) (.169 ± .012) (.110 ± .012) (.059) (.094) (.051) (.020) (.004 ± .004) (.035) (.039) (.005) (.150) (.138) (.138)
X 7343-43 7.3 ± 0.3 4.3 ± 0.3 4.0 ± 0.3 2.3 2.4 1.3 0.5 0.10 ± 0.10 1.7 1.0 0.13 3.8 3.5** 3.5**
(.287 ± .012) (.169 ± .012) (.157 ± .012) (.091) (.094) (.051) (.020) (.004 ± .004) (.067) (.039) (.005) (.150) (.138) (.138)
E 7260-38 7.3 ± 0.3 6.0 ± 0.3 3.6 ± 0.2 2.3 4.1 1.3 0.5 0.10 ± 0.10 0.9 1.0 0.13 3.8 3.5 3.5
(.287 ± .012) (.236 ± .012) (.142 ± .008) (.091) (.161) (.051) (.020) (.004 ± .004) (.035) (.039) (.005) (.150) (.138) (.138)

Notes: 1. Metric dimensions govern.

2. (Ref) - Dimensions provided for reference only.
* Mil-C-55365/8 Specified Dimensions
** Round Glue Pad: 2.9 ±0.1mm (0.114" ± 0.004") in diameter at KEMET’s option

LOW PROFILE T491 DIMENSIONS

Millimeters (inches)
CASE SIZE COMPONENT
X T A G E
KEMET EIA L W H Max. K Min. F ± 0.1 S ± 0.3
(Ref) (Ref) (Min) (Ref) (Ref)
R 2012-12 2.0 ± 0.2 1.3 ± 0.2 1.2 0.3 0.9 0.5 0.05 0.13 0.8 0.5 0.8
(.079 ± .008) (.051 ± .008) (.047) (.012) (.035) (.020) (.002) (.005) (.031) (.020) (.031)
S 3216-12 3.2 ± 0.2 1.6 ± 0.2 1.2 0.3 1.2 0.8 0.05 0.13 0.8 1.1 1.3
(.126 ± .008) (.063 ± .008) (.047) (.012) (.047) (.031) (.002) (.005) (.031) (.043) (.051)
3528-12 3.5 ± 0.2 2.8 ± 0.2 1.2 0.3 2.2 0.8 0.05 0.13 1.1 1.8 2.2
T
(.138 ± .008) (.110 ± .008) (.047) (.012) (.087) (.031) (.002) (.005) (.043) (.071) (.087)
6032-15 6.0 ± 0.3 3.2 ± 0.3) 1.5 0.5 2.2 1.3 0.05 0.13 2.5 2.8 2.4
U
(.236 ± .012) (.126 ± .012) (.059) (.020) (.087) (.051) (.002) (.005) (.098) (.110) (.094)
V 7343-20 7.3 ± 0.3 4.3 ± 0.3 2.0 0.9 2.4 1.3 0.05 0.13 3.8 3.5 3.5
(.287 ± .012) (.169 ± .012) (.079) (.035) (.094) (.051) (.002) (.005) (.150) (.138) (.138)
Notes: 1. Metric dimensions govern.
2. (Ref) - Dimensions provided for reference only.
3. No dimensions provided for B, P or R because low profile cases do not have a bevel or a notch.

T491 ORDERING INFORMATION

T 491 B 105 M 035 A S*
Lead Material
Tantalum S = 100% Tin (Sn) Plated
H = Standard Solder - Coated (90% Sn 10% Pb)
Series G = Gold Plated (A,B,C,D,X only)
T491 - Precision Molded T = 100% Tin (Sn) Plated
Case Size Failure Rate
A,B,C,D,E,R,S,T,U,V,X A = Not Applicable
Capacitance Picofarad Code Voltage
First two digits represent significant figures. As shown
Third digit specifies number of zeros to follow. Capacitance Tolerance
*Part number example: T491B105M035AS (14 digits - no spaces). See www.kemet.com for Pb Free transition. M = ±20%; K = ±10%
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 15
 SOLID TANTALUM CHIP CAPACITORS
T491 SERIES—Precision Molded Chip

T491 TANTALUM CHIP CAPACITANCE VALUES

Case Size by Capacitance and Voltage
Capacitance Rated Voltage @ +85°C
µF Code 2.5 3 4 6 10 16 20 25 35 50
0.10 104 A A

0.15 154 A A/B

0.22 224 A B

0.33 334 A A B

0.47 474 A A/B B/C

0.68 684 A A A/B B/C

1.0 105 A R/S/A A/B A/B V/C

1.5 155 A A S/A A/B B/C C/D

2.2 225 R/A A/B R/S/A A/B B/C B/C C/D

3.3 335 A A R/S/A A/B T/A/B B/C B/C D

A/B
4.7 475 A S/A A/B/T A/B/C B/C C/D D
R/S
R/S S/T
6.8 685 S/A A/B/C U/B/C B/C C/D D/X
A/B A/B
R/S R/S/T S/T/A B/C/U
10.0 106 U/B/C C/D V/C/D X
A/B A/B B/C T/A
S/T S/T T/U
15.0 156 U/B/C C/D C/D D/X X
A/B A/B/C A/B/C
S/T U/T T/U U/B
22.0 226 V/C/D V/C/D D/X
A/B/C A/B/C A/B/C C/D
T/U T/U U/V
33.0 336 A U/C/D V/C/D D/X X
A/B/C A/B/C B/C/D
T/U T/U/A U/V
47.0 476 V/C/D D D/X X/E
A/B/C B/C/D B/C/D
U/A U/B U/V
68.0 686 V/D D/X X
B/C/D C/D B/C/D
T/U/A U/V
100.0 107 T V/C/D V/D/X X
B/C/D B/C/D
V/B V/C
150.0 157 V/C/D D/X
C/D D/X
V/C
220.0 227 V V/D/X X
D/X

330.0 337 V/C/D D/X D/X

470.0 477 D/X D/X X/E

680.0 687 D/X E

1000.0 108 X/E

16 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 SOLID TANTALUM CHIP CAPACITORS
T491 SERIES - Precision Molded Chip
T491 RATINGS & PART NUMBER REFERENCE
DC DF % ESR Ω DC DF % ESR Ω
Capaci- Capaci-
Case KEMET Leakage @ +25ºC @ +25°C Case KEMET Leakage @ +25ºC @ +25°C
tance tance
Size Part Number µA @ 25ºC 120 Hz 100 kHz Size Part Number µA @ 25ºC 120 Hz 100 kHz
µF µF
Max Max Max Max Max Max
2.5 Volt Rating at +85ºC (1.7 Volt Rating at +125ºC) **6 Volt Rating at +85ºC (4 Volt Rating at +125ºC)
100.0 T T491T107(1)2R5A(2) 2.5 24.0 3.9 15.0 C T491C156(1)006A(2) 0.9 6.0 1.8
3 Volt Rating at +85ºC (2 Volt Rating at +125ºC) 15.0 B T491B156(1)006A(2) 0.9 6.0 3.5
#33.0 *A T491A336(1)003A(2) 1.0 6.0 4.0 #15.0 A T491A156(1)006A(2) 0.9 6.0 4.0
4 Volt Rating at +85ºC (2.7 Volt Rating at +125ºC) #15.0 T T491T156(1)006A(2) 0.9 6.0 5.0
3.3 A T491A335(1)004A(2) 0.5 6.0 8.0 #15.0 *S T491S156M006A(2) 0.9 15.0 10.0
4.7 A T491A475(1)004A(2) 0.5 6.0 8.0 22.0 C T491C226(1)006A(2) 1.4 6.0 1.8
6.8 A T491A685(1)004A(2) 0.5 6.0 6.0 22.0 U T491U226(1)006A(2) 1.4 6.0 1.8

Solid Tantalum Surface Mount

6.8 S T491S685(1)004A(2) 0.5 6.0 15.0 22.0 B T491B226(1)006A(2) 1.4 6.0 3.5
10.0 B T491B106(1)004A(2) 0.5 6.0 3.5 #22.0 A T491A226(1)006A(2) 1.4 6.0 4.0
10.0 A T491A106(1)004A(2) 0.5 6.0 6.0 #22.0 T T491T226M006A(2) 1.4 8.0 5.0
#10.0 *S T491S106(1)004A(2) 0.5 6.0 15.0 33.0 C T491C336(1)006A(2) 2.0 6.0 1.8
#10.0 *R T491R106M004A(2) 0.5 8.0 10.0 33.0 U T491U336(1)006A(2) 2.0 6.0 1.8
15.0 B T491B156(1)004A(2) 0.6 6.0 3.5 #33.0 B T491B336(1)006A(2) 2.0 6.0 3.0
15.0 A T491A156(1)004A(2) 0.6 6.0 4.0 #33.0 *A T491A336(1)006A(2) 2.0 12.0 2.5
15.0 T T491T156(1)004A(2) 0.6 6.0 5.0 #33.0 *T T491T336M006A(2) 2.0 12.0 6.0
#15.0 *S T491S156M004A(2) 0.6 10.0 15.0 47.0 D T491D476(1)006A(2) 2.9 6.0 0.8
22.0 C T491C226(1)004A(2) 0.9 6.0 1.8 47.0 C T491C476(1)006A(2) 2.9 6.0 1.6
22.0 B T491B226(1)004A(2) 0.9 6.0 3.5 #47.0 U T491U476(1)006A(2) 2.9 6.0 1.8
#22.0 A T491A226(1)004A(2) 0.9 6.0 4.0 #47.0 B T491B476(1)006A(2) 2.9 6.0 3.5
#22.0 *T T491T226(1)004A(2) 0.9 6.0 5.0 †47.0 *A T491A476M006A(2) 3.0 12.0 3.5
22.0 *S T491S226M004A(2) 0.9 10.0 10.0 *47.0 *T T491T476(1)006A(2) 3.0 24.0 4.4
33.0 C T491C336(1)004A(2) 1.3 6.0 1.8 68.0 D T491D686(1)006A(2) 4.1 6.0 0.8
33.0 U T491U336(1)004A(2) 1.3 6.0 1.8 #68.0 C T491C686(1)006A(2) 4.1 6.0 1.2
33.0 B T491B336(1)004A(2) 1.3 6.0 3.5 #68.0 *U T491U686(1)006A(2) 4.1 10.0 1.8
#33.0 A T491A336(1)004A(2) 1.3 6.0 4.0 #68.0 *B T491B686(1)006A(2) 4.1 8.0 1.0
#33.0 *T T491T336M004A(2) 1.3 8.0 5.0 100.0 D T491D107(1)006A(2) 6.0 8.0 0.8
47.0 C T491C476(1)004A(2) 1.9 6.0 1.8 100.0 V T491V107(1)006A(2) 6.0 8.0 0.7
47.0 U T491U476(1)004A(2) 1.9 6.0 1.8 #100.0 C T491C107(1)006A(2) 6.0 8.0 1.2
#47.0 B T491B476(1)004A(2) 1.9 6.0 3.0 #100.0 *U T491U107M006A(2) 6.0 10.0 1.8
#47.0 A T491A476M004A(2) 1.9 12.0 2.5 #100.0 *B T491B107M006A(2) 6.3 15.0 3.0
#47.0 *T T491T476M004A(2) 1.9 12.0 6.0 150.0 D T491D157(1)006A(2) 9.0 8.0 0.7
68.0 D T491D686(1)004A(2) 2.7 6.0 0.8 #150.0 *C T491C157(1)006A(2) 9.0 8.0 1.2
68.0 C T491C686(1)004A(2) 2.7 6.0 1.6 #150.0 *V T491V157(1)006A(2) 9.0 8.0 0.7
#68.0 *U T491U686(1)004A(2) 2.7 6.0 1.8 220.0 X T491X227(1)006A(2) 13.2 8.0 0.7
#68.0 B T491B686(1)004A(2) 2.7 6.0 3.5 #220.0 D T491D227(1)006A(2) 13.2 8.0 0.7
#68.0 *A T491A686(1)004A(2) 2.8 30.0 4.0 #220.0 *C T491C227M006A(2) 13.2 10.0 1.2
100.0 D T491D107(1)004A(2) 4.0 8.0 0.8 #220.0 *V T491V227M006A(2) 13.2 12.0 0.7
#100.0 C T491C107(1)004A(2) 4.0 8.0 1.2 330.0 *X T491X337(1)006A(2) 19.8 8.0 0.5
#100.0 *U T491U107(1)004A(2) 4.0 10.0 1.8 330.0 *D T491D337(1)006A(2) 19.8 8.0 0.5
#100.0 *B T491B107M004A(2) 4.0 8.0 1.0 470.0 *X T491X477(1)006A(2) 28.2 10.0 0.5
†100.0 *A T491A107M004A(2) 4.0 30.0 4.0 470.0 *D T491D477M006A(2) 28.2 12.0 0.5
†100.0 *T T491T107M004A(2) 4.0 30.0 5.0 680.0 *E T491E687M006A(2) 40.8 12.0 0.5
150.0 D T491D157(1)004A(2) 6.0 8.0 0.8 10 Volt Rating at +85ºC (7 Volt Rating at +125ºC)
150.0 V T491V157(1)004A(2) 6.0 8.0 0.7 1.5 A T491A155(1)010A(2) 0.5 6.0 8.0
#150.0 *C T491C157(1)004A(2) 6.0 8.0 1.2 2.2 B T491B225(1)010A(2) 0.5 6.0 3.5
†150.0 *B T491B157M004A(2) 6.0 12.0 2.0 2.2 A T491A225(1)010A(2) 0.5 6.0 8.0
#220.0 *V T491V227(1)004A(2) 8.8 8.0 0.7 3.3 A T491A335(1)010A(2) 0.5 6.0 6.0
330.0 D T491D337(1)004A(2) 13.2 8.0 0.7 3.3 S T491S335(1)010A(2) 0.5 6.0 15.0
†330.0 *V T491V337(1)004A(2) 13.2 12.0 0.7 #3.3 *R T491R335(1)010A(2) 0.3 8.0 15.0
#330.0 *C T491C337(1)004A(2) 13.2 10.0 1.2 4.7 B T491B475(1)010A(2) 0.5 15.0 3.5
#470.0 X T491X477(1)004A(2) 18.8 8.0 0.5 4.7 A T491A475(1)010A(2) 0.5 6.0 6.0
#470.0 *D T491D477(1)004A(2) 18.8 8.0 0.8 #4.7 S T491S475(1)010A(2) 0.5 6.0 15.0
#680.0 *X T491X687M004A(2) 27.2 12.0 0.5 #4.7 *R T491R475M010A(2) 0.5 8.0 10.0
#680.0 *D T491D687M004A(2) 27.2 12.0 0.5 6.8 B T491B685(1)010A(2) 0.7 6.0 3.5
#1000.0 *X T491X108(1)004A(2) 40.0 12.0 0.5 6.8 A T491A685(1)010A(2) 0.7 6.0 6.0
#1000.0 *E T491E108M004A(2) 40.0 15.0 0.2 6.8 T T491T685(1)010A(2) 0.7 6.0 5.0
**6 Volt Rating at +85ºC (4 Volt Rating at +125ºC) #6.8 *S T491S685M010A(2) 0.7 10.0 15.0
2.2 R T491R225(1)006A(2) 0.5 6.0 25.0 10.0 C T491C106(1)010A(2) 1.0 6.0 1.8
2.2 A T491A225(1)006A(2) 0.5 6.0 8.0 10.0 B T491B106(1)010A(2) 1.0 6.0 3.5
3.3 A T491A335(1)006A(2) 0.5 6.0 8.0 #10.0 A T491A106(1)010A(2) 1.0 6.0 4.0
4.7 A T491A475(1)006A(2) 0.5 6.0 6.0 #10.0 T T491T106(1)010A(2) 1.0 6.0 5.0
4.7 S T491S475(1)006A(2) 0.5 6.0 15.0 #10.0 *S T491S106M010A(2) 1.0 10.0 15.0
6.8 B T491B685(1)006A(2) 0.5 6.0 3.5 15.0 C T491C156(1)010A(2) 1.5 6.0 1.8
6.8 A T491A685(1)006A(2) 0.5 6.0 6.0 15.0 U T491U156(1)010A(2) 1.5 6.0 1.8
#6.8 S T491S685(1)006A(2) 0.5 6.0 15.0 15.0 B T491B156(1)010A(2) 1.5 6.0 3.5
#6.8 *R T491R685(1)006A(2) 0.5 8.0 15.0 #15.0 *A T491A156(1)010A(2) 1.5 8.0 6.0
10.0 B T491B106(1)006A(2) 0.6 6.0 3.5 #15.0 *T T491T156M010A(2) 1.5 8.0 5.0
10.0 A T491A106(1)006A(2) 0.6 6.0 4.0
10.0 T T491T106(1)006A(2) 0.6 6.0 5.0
#10.0 *S T491S106M006A(2) 0.6 10.0 15.0
#10.0 *R T491R106(1)006A(2) 0.6 8.0 10.0
*Extended Values
**6 Volt product equivalent to 6.3 volt product.
#Maximum Capacitance Change @ 125ºC=+15%.
†Maximum Capacitance Change @ 125ºC=+20%.

(1) To complete KEMET Part Number, insert M for ±20% tolerance or K for ±10% tolerance.
Higher voltage ratings and tighter capacitance tolerance product may be
substituted within the same size at KEMET’s option. Voltage substitutions
will be marked with the higher voltage rating.

Note: Refer to T491 Ordering Information on page 15 for lead termination options.

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 17
 SOLID TANTALUM CHIP CAPACITORS
T491 SERIES—Precision Molded Chip

T491 RATINGS & PART NUMBER REFERENCE

DC DF % ESR Ω DC DF % ESR Ω
Capaci- Capaci-
Case KEMET Leakage @ +25ºC @ +25°C Case KEMET Leakage @ +25ºC @ +25°C
tance tance
Size Part Number µA @ 25ºC 120 Hz 100 kHz Size Part Number µA @ 25ºC 120 Hz 100 kHz
µF µF
Max Max Max Max Max Max
10 Volt Rating at +85ºC (7 Volt Rating at +125ºC) 16 Volt Rating at +85ºC (10 Volt Rating at +125ºC)
22.0 C T491C226(1)010A(2) 2.2 6.0 1.8 100.0 X T491X107(1)016A(2) 16.0 8.0 0.7
22.0 U T491U226(1)010A(2) 2.2 6.0 1.8 †100.0 *V T491V107(1)016A(2) 16.0 12.0 0.7
#22.0 B T491B226(1)010A(2) 2.2 6.0 3.0 #100.0 *D T491D107(1)016A(2) 16.0 8.0 0.7
#22.0 *A T491A226M010A(2) 2.2 10.0 6.0 #150.0 *X T491X157(1)016A(2) 24.0 8.0 0.5
#22.0 *T T491T226M010A(2) 2.2 12.0 8.0 #150.0 *D T491D157(1)016A(2) 24.0 12.0 0.7
33.0 D T491D336(1)010A(2) 3.3 6.0 0.8 #270.0 *X T491X227(1)016A(2) 35.2 10.0 0.5
33.0 V T491V336(1)010A(2) 3.3 6.0 0.7
20 Volt Rating at +85ºC (13 Volt Rating at + 125ºC)
33.0 C T491C336(1)010A(2) 3.3 6.0 1.6
#33.0 U T491U336(1)010A(2) 3.3 6.0 1.8 0.68 A T491A684(1)020A(2) 0.5 4.0 12.0
#33.0 B T491B336(1)010A(2) 3.3 6.0 3.5 1.0 A T491A105(1)020A(2) 0.5 4.0 10.0
47.0 D T491D476(1)010A(2) 4.7 6.0 0.8 1.0 S T491S105(1)020A(2) 0.5 6.0 18.0
47.0 V T491V476(1)010A(2) 4.7 6.0 0.7 #1.0 R T491R105M020A(2) 0.5 6.0 20.0
#47.0 C T491C476(1)010A(2) 4.7 6.0 1.2 1.5 A T491A155(1)020A(2) 0.5 6.0 8.0
#47.0 *U T491U476(1)010A(2) 4.7 10.0 2.2 1.5 S T491S155(1)020A(2) 0.5 6.0 15.0
#47.0 *B T491B476M010A(2) 4.7 8.0 1.0 2.2 B T491B225(1)020A(2) 0.5 6.0 3.5
68.0 D T491D686(1)010A(2) 6.8 6.0 0.8 2.2 A T491A225(1)020A(2) 0.5 6.0 7.0
68.0 V T491V686(1)010A(2) 6.8 6.0 0.7 3.3 B T491B335(1)020A(2) 0.7 6.0 3.5
#68.0 C T491C686(1)010A(2) 6.8 6.0 1.2 #3.3 *A T491A335(1)020A(2) 0.7 6.0 7.0
#68.0 *U T491U686M010A(2) 6.8 10.0 1.8 3.3 *T T491T335(1)020A(2) 0.7 6.0 5.0
#68.0 *B T491B686M010A(2) 6.8 10.0 3.0 4.7 C T491C475(1)020A(2) 1.0 6.0 2.4
100.0 D T491D107(1)010A(2) 10.0 8.0 0.7 4.7 B T491B475(1)020A(2) 1.0 6.0 3.5
#100.0 *C T491C107(1)010A(2) 10.0 8.0 1.2 #4.7 *A T491A475(1)020A(2) 1.0 8.0 6.0
#100.0 V T491V107(1)010A(2) 10.0 8.0 0.7 6.8 C T491C685(1)020A(2) 1.4 6.0 1.9
150.0 X T491X157(1)010A(2) 15.0 8.0 0.7 6.8 U T491U685(1)020A(2) 1.4 6.0 1.9
#150.0 D T491D157(1)010A(2) 15.0 8.0 0.7 #6.8 *B T491B685(1)020A(2) 1.4 6.0 3.5
#150.0 *C T491C157(1)010A(2) 15.0 10.0 1.2 10.0 C T491C106(1)020A(2) 2.0 6.0 1.8
#150.0 *V T491V157M010A(2) 15.0 8.0 0.7 10.0 U T491U106(1)020A(2) 2.0 6.0 1.8
#220.0 X T491X227(1)010A(2) 22.0 8.0 0.5 #10.0 *B T491B106(1)020A(2) 2.0 6.0 3.0
#220.0 *D T491D227(1)010A(2) 22.0 8.0 0.5 15.0 D T491D156(1)020A(2) 3.0 6.0 1.0
#220.0 *V T491V227(1)010A(2) 22.0 12.0 0.7 15.0 C T491C156(1)020A(2) 3.0 6.0 1.7
#330.0 *D T491D337M010A(2) 33.0 10.0 0.5 22.0 D T491D226(1)020A(2) 4.4 6.0 0.8
#330.0 *X T491X337(1)010A(2) 33.0 10.0 0.5 22.0 V T491V226(1)020A(2) 4.4 6.0 0.7
#470.0 *X T491X477(1)010A(2) 47.0 10.0 0.2 #22.0 *C T491C226(1)020A(2) 4.4 6.0 1.2
#470.0 *E T491E477M010A(2) 47.0 12.0 0.5 33.0 D T491D336(1)020A(2) 6.6 6.0 0.8
16 Volt Rating at +85ºC (10 Volt Rating at +125ºC) #33.0 *C T491C336M020A(2) 6.6 6.0 1.2
†33.0 *V T491V336(1)020A(2) 6.6 8.0 0.7
1.0 A T491A105(1)016A(2) 0.5 4.0 10.0 47.0 *D T491D476(1)020A(2) 9.4 6.0 0.7
1.5 A T491A155(1)016A(2) 0.5 6.0 8.0 68.0 X T491X686(1)020A(2) 13.6 6.0 0.7
2.2 A T491A225(1)016A(2) 0.5 6.0 6.0 #68.0 *D T491D686(1)020A(2) 13.6 8.0 0.7
2.2 *S T491S225(1)016A(2) 0.5 6.0 15.0 #100.0 *X T491X107(1)020A(2) 20.0 8.0 0.5
#2.2 *R T491R225(1)016A(2) 0.5 8.0 25.0
25 Volt Rating at +85ºC (17 Volt Rating at +125ºC)
3.3 B T491B335(1)016A(2) 0.5 6.0 3.5
3.3 A T491A335(1)016A(2) 0.5 6.0 6.0 0.33 A T491A334(1)025A(2) 0.5 4.0 15.0
4.7 B T491B475(1)016A(2) 0.8 6.0 3.5 0.47 A T491A474(1)025A(2) 0.5 4.0 14.0
4.7 A T491A475(1)016A(2) 0.8 6.0 6.0 0.68 A T491A684(1)025A(2) 0.5 4.0 10.0
4.7 T T491T475(1)016A(2) 0.8 6.0 5.0 1.0 B T491B105(1)025A(2) 0.5 4.0 5.0
6.8 C T491C685(1)016A(2) 1.1 6.0 1.9 1.0 *A T491A105(1)025A(2) 0.5 4.0 8.0
6.8 B T491B685(1)016A(2) 1.1 6.0 3.5 1.5 B T491B155(1)025A(2) 0.5 6.0 5.0
#6.8 *A T491A685(1)016A(2) 1.1 6.0 7.0 1.5 *A T491A155(1)025A(2) 0.5 6.0 10.0
10.0 C T491C106(1)016A(2) 1.6 6.0 1.8 2.2 C T491C225(1)025A(2) 0.6 6.0 3.5
10.0 U T491U106(1)016A(2) 1.6 6.0 1.8 2.2 B T491B225(1)025A(2) 0.6 6.0 4.5
10.0 B T491B106(1)016A(2) 1.6 6.0 3.5 3.3 C T491C335(1)025A(2) 0.9 6.0 2.5
#10.0 *A T491A106(1)016A(2) 1.6 10.0 7.0 3.3 B T491B335(1)025A(2) 0.9 6.0 3.5
#10.0 *T T491T106M016A(2) 1.6 8.0 8.0 4.7 C T491C475(1)025A(2) 1.2 6.0 2.4
15.0 C T491C156(1)016A(2) 2.4 6.0 1.8 #4.7 *B T491B475(1)025A(2) 1.2 6.0 1.5
15.0 U T491U156(1)016A(2) 2.4 6.0 1.8 6.8 C T491C685(1)025A(2) 1.7 6.0 1.9
#15.0 *B T491B156(1)016A(2) 2.4 6.0 3.0 6.8 *B T491B685(1)025A(2) 1.7 8.0 3.0
22.0 D T491D226(1)016A(2) 3.6 6.0 0.8 10.0 D T491D106(1)025A(2) 2.5 6.0 1.0
22.0 C T491C226(1)016A(2) 3.6 6.0 1.6 10.0 C T491C106(1)025A(2) 2.5 6.0 1.5
#22.0 *U T491U226(1)016A(2) 3.6 10.0 3.0 15.0 D T491D156(1)025A(2) 3.8 6.0 1.0
#22.0 *B T491B226(1)016A(2) 3.6 6.0 2.2 #15.0 *C T491C156(1)025A(2) 3.8 6.0 1.5
33.0 D T491D336(1)016A(2) 5.3 6.0 0.8 22.0 D T491D226(1)025A(2) 5.5 6.0 0.8
#33.0 *C T491C336(1)016A(2) 5.3 6.0 1.2 22.0 *C T491C226(1)025A(2) 5.5 8.0 1.5
#33.0 *U T491U336(1)016A(2) 5.3 12.0 3.0 22.0 *V T491V226(1)025A(2) 5.5 6.0 0.7
47.0 D T491D476(1)016A(2) 7.5 6.0 0.8 33.0 X T491X336(1)025A(2) 8.3 6.0 0.7
47.0 V T491V476(1)016A(2) 7.5 6.0 0.7 #33.0 *D T491D336(1)025A(2) 8.3 6.0 0.7
#47.0 *C T491C476(1)016A(2) 7.5 6.0 1.2 #47.0 *X T491X476(1)025A(2) 11.8 6.0 0.7
68.0 *V T491V686(1)016A(2) 10.9 6.0 0.7 †47.0 *D T491D476(1)025A(2) 11.8 10.0 0.7
68.0 D T491D686(1)016A(2) 10.9 6.0 0.7 †68.0 *X T491X686M025A(2) 17.0 8.0 0.7
*Extended Values
**6 Volt product equivalent to 6.3 volt product.
#Maximum Capacitance Change @ 125ºC=+15%.
†Maximum Capacitance Change @ 125ºC=+20%.

(1) To complete KEMET Part Number, insert M for ±20% tolerance or K for ±10% tolerance.
Higher voltage ratings and tighter capacitance tolerance product may be
substituted within the same size at KEMET’s option. Voltage substitutions
will be marked with the higher voltage rating.

Note: Refer to T491 Ordering Information on page 15 for lead termination options.

18 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 SOLID TANTALUM CHIP CAPACITORS
SOLID TANTALUM CHIP CAPACITORS
T491 SOLIDd Chip
T491 SERIES - Precision Molded Chip

T49T491 RATINGS & PART NUMBER REFERENCE

DC DF % ESR Ω
Capaci-
Case KEMET Leakage @ +25ºC @ +25°C
tance
Size Part Number µA @ 25ºC 120 Hz 100 kHz
µF
Max Max Max
35 Volt Rating at +85ºC (23 Volt Rating at +125ºC)
0.10 A T491A104(1)035A(2) 0.5 4.0 20.0
0.15 A T491A154(1)035A(2) 0.5 4.0 19.0
0.22 A T491A224(1)035A(2) 0.5 4.0 18.0
0.33 A T491A334(1)035A(2) 0.5 4.0 15.0
0.47 B T491B474(1)035A(2) 0.5 4.0 8.0

Solid Tantalum Surface Mount

0.47 A T491A474(1)035A(2) 0.5 4.0 14.0
0.68 B T491B684(1)035A(2) 0.5 4.0 6.5
0.68 *A T491A684(1)035A(2) 0.5 4.0 10.0
1.0 B T491B105(1)035A(2) 0.5 4.0 5.0
1.0 *A T491A105(1)035A(2) 0.5 4.0 10.0
1.5 C T491C155(1)035A(2) 0.5 6.0 4.5
1.5 B T491B155(1)035A(2) 0.5 6.0 5.0
2.2 C T491C225(1)035A(2) 0.8 6.0 3.5
2.2 *B T491B225(1)035A(2) 0.8 6.0 4.0
3.3 C T491C335(1)035A(2) 1.2 6.0 2.5
#3.3 *B T491B335(1)035A(2) 1.2 6.0 3.5
4.7 D T491D475(1)035A(2) 1.7 6.0 1.5
4.7 C T491C475(1)035A(2) 1.7 6.0 2.5
6.8 D T491D685(1)035A(2) 2.4 6.0 1.3
6.8 *C T491C685(1)035A(2) 2.4 6.0 2.0
10.0 D T491D106(1)035A(2) 3.5 6.0 1.0
#10.0 *C T491C106M035A(2) 3.5 6.0 2.0
#10.0 *V T491V106(1)035A(2) 3.5 6.0 2.0
15.0 X T491X156(1)035A(2) 5.3 6.0 0.9
15.0 D T491D156(1)035A(2) 5.3 6.0 0.8
22.0 X T491X226(1)035A(2) 7.7 6.0 0.7
#22.0 *D T491D226(1)035A(2) 7.7 6.0 0.7
#33.0 *X T491X336(1)035A(2) 11.6 6.0 0.6
†47.0 *X T491X476(1)035A(2) 16.5 8.0 0.6
#47.0 *E T491E476(1)035A(2) 16.5 10.0 0.5
50 Volt Rating at +85ºC (33 Volt Rating at + 125ºC)
0.10 A T491A104(1)050A(2) 0.5 4.0 20.0
0.15 B T491B154(1)050A(2) 0.5 4.0 16.0
0.15 *A T491A154(1)050A(2) 0.5 4.0 19.0
0.22 B T491B224(1)050A(2) 0.5 4.0 14.0
0.33 B T491B334(1)050A(2) 0.5 4.0 10.0
0.47 C T491C474(1)050A(2) 0.5 4.0 8.0
0.47 *B T491B474(1)050A(2) 0.5 4.0 9.0
0.68 C T491C684(1)050A(2) 0.5 4.0 7.0
0.68 *B T491B684(1)050A(2) 0.5 4.0 8.0
1.0 C T491C105(1)050A(2) 0.5 4.0 5.5
1.0 *V T491V105M050A(2) 0.5 4.0 6.0
1.5 D T491D155(1)050A(2) 0.8 6.0 3.5
1.5 *C T491C155(1)050A(2) 0.8 6.0 4.5
2.2 D T491D225(1)050A(2) 1.1 6.0 2.5
2.2 *C T491C225(1)050A(2) 1.1 6.0 3.5
3.3 D T491D335(1)050A(2) 1.7 6.0 2.0
4.7 D T491D475(1)050A(2) 2.4 6.0 1.5
6.8 X T491X685(1)050A(2) 3.5 6.0 1.0
#6.8 *D T491D685(1)050A(2) 3.4 6.0 1.0
#10.0 *X T491X106M050A(2) 5.0 6.0 0.7
†15.0 *X T491X156(1)050A(2) 7.5 8.0 0.7
* Extended Values
** 6 Volt product equivalent to 6.3 volt product
# Maximum Capacitance Change @ 125°C = +15%
† Maximum Capacitance Change @ 125°C = +20%
(1) To complete KEMET Part Number, insert M for ±20% tolerance or K for ±10% tolerance.
High voltage ratings and tighter capacitance tolerance product may be substituted
within the same size at KEMET's option. Voltage substitutions will be marked with the
higher voltage rating.
Note: Refer to T491 Ordering Information on page 15 for lead termination options.

CAPACITOR MARKINGS CONSTRUCTION

T491 Series — All Case Sizes
Negative Silver Adhesive Polarity
Termination* Washer Stripe (+)
Molded Polarity
Case Bevel (+)
Polarity
Indicator (+)
Tantalum
Wire

226 Picofarad
Code

Rated
Voltage
20K KEMET
I. D. Symbol

Tantalum

442 (Ta2O5)

Mn02 Coat
(First Layer)
Weld

Carbon
(Second Layer)
Print Week Code: Positive
1st Digit = Year
Silver Paint Termination*
(Third Layer)
2nd & 3rd Digits = Week *100% tin
"442" = The 42nd week of 2004

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 19
 SOLID TANTALUM CHIP CAPACITORS
T492 SERIES—Style CWR11 Per Mil-PRF-55365/8
• Established reliability military version of • Qualified to MIL-PRF-55365/8, Style CWR11:
Industrial Grade T491 series – Termination Code H, solder-plated
• Taped and reeled per EIA 481-1 – Weibull failure rate codes B, C and D
• Precision-molded, laser-marked case – Capacitance values and voltages as shown
• Symmetrical, compliant terminations in following part number table. (Contact
• 100% Surge Current test on C, D sizes KEMET for latest qualification status)

T492 OUTLINE DRAWINGS

CATHODE (-) END SIDE VIEW ANODE (+) END BOTTOM VIEW
VIEW VIEW
B
W
B

H E F
K T P

S S R Termination A
X G cutout at L
KEMET’s
Option,
either end

DIMENSIONS – Millimeters (Inches)

CASE SIZE COMPONENT
±0.20 B ±0.15 X P R T A G E
F* ±-0.1 ±0.3
L* W* H* K* ±(.008) S* ±(.012)
KEMET EIA ±(.004) (Ref) ± (.006) (Ref) (Ref) (Ref) (Ref) (Min) (Ref) (Ref)
A 3216-18 3.2 ± 0.2 1.6 ± 0.2 1.6 ± 0.2 0.9 1.2 0.8 0.4 0.10 ± 0.10 0.4 0.4 0.13 0.8 1.1 1.3
(.126 ± .008) (.063 ± .008) (.063 ± .008) (.035) (.047) (.031) (.016) (.004 ± .004) (.016) (.016) (.005) (.031) (.043) (.051)
B 3528-21 3.5 ± 0.2 2.8 ± 0.2 1.9 ± 0.2 1.1 2.2 0.8 0.4 0.10 ± 0.10 0.5 1.0 0.13 1.1 1.8 2.2
(.138 ± .008) (.110 ± .008) (.075 ± .008) (.043) (.087) (.031) (.016) (.004 ± .004) (.020) (.039) (.005) (.043) (.071) (.087)
C 6032-28 6.0 ± 0.3 3.2 ± 0.3 2.5 ± 0.3 1.4 2.2 1.3 0.5 0.10 ± 0.10 0.9 1.0 0.13 2.5 2.8 2.4
(.236 ± .012) (.126 ± .012) (.098 ± .012) (.055) (.087) (.051) (.020) (.004 ± .004) (.035) (.039) (.005) (.098) (.110) (.094)
D 7343-31 7.3 ± 0.3 4.3± 0.3 2.8 ± 0.3 1.5 2.4 1.3 0.5 0.10 ± 0.10 0.9 1.0 0.13 3.8 3.5 3.5
(.287 ± .012) (.169 ± .012) (.110 ± .012) (.059) (.094) (.051) (.020) (.004 ± .004) (.035) (.039) (.005) (.150) (.138) (.138)

Notes: 1. Metric dimensions govern. * Mil-C-55365/8 Specified Dimensions

2. (Ref) - Dimensions provided for reference only.

ORDERING INFORMATION — MIL-PRF-55365 Part Number

CWR11 M H 105 K B Z

Style Surge Current Option

Capacitors, Chip, Fixed Tantalum A = +25°C after Weibull
A =Weibull
B = -55° +85° after +25°C
Established Reliability, (encapsulated) C = -55°, 0°, & +85°C before Weibull
Z = None
Z = None
Voltage Failure Rate Symbol*
D = 6V J = 20V (*See Note Below)
F = 10V K = 25V B = (0.1%/1000 hrs.
H = 15V M - 35V C = (0.01%/1000 hrs.
Termination Finish Code D = (0.001%/1000 hrs.
H = Solder Plated Capacitance Tolerance
Capacitance Picofarad Code M = ±20%
First two digits represent significant figures. K = ±10%
Third digit specifies number of zeros to follow. J = ±5%

T492 SERIES ORDERING INFORMATION — KEMET Part Number

T 492 B 105 K 035 B S*
Tantalum Lead Material
S - Tin-Lead (Sn/Pb) Coated
Series (Contact KEMET Sales Rep. for additional Lead Material options)
T492 - Precision Molded, Style CWR11 Failure Rate Symbol*
Case Size (*See Note Below)
A, B, C, D B (0.1%/1000 hrs.)
C (0.01%/1000 hrs.)
Capacitance Picofarad Code
D (0.001%/1000 hrs.)
First two digits represent significant figures.
Third digit specifies number of zeros to follow. Voltage
Capacitance Tolerance
M - ± 20%
* Part Number Example: T492B105K035BS (14 digits - no spaces) K - ± 10%
* See www.kemet.com for Pb Free transition. J - ± 5%
*Note on Failure Rates: Exponential failure rate levels M, P, R and S are inactive for new design per Mil-C-55365.
Parts qualified to Weibull failure rate levels are substitutable for exponential failure rate levels.
20 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 SOLID TANTALUM CHIP CAPACITORS
T492 SERIES—Style CWR11 Per Mil-PRF-55365/8

T492 (CWR11) RATINGS AND PART NUMBER REFERENCE

DC DF ESR
Capaci- Leakage % @ +25C  @ +25C
tance Case KEMET Mil-C-55365/8 A @ +25C 120 Hz 100kHz
F Size Part Number Part Number Max Max Max
6 Volt Rating at +85C (4 Volt Rating at +125C)
1.5 A T492A155(1)006(2)S CWR11DH155(1)(2) 0.5 6.0 8.0
2.2 A T492A225(1)006(2)S CWR11DH225(1)(2) 0.5 6.0 8.0
3.3 A T492A335(1)006(2)S CWR11DH335(1)(2) 0.5 6.0 8.0

Solid Tantalum Surface Mount

4.7 B T492B475(1)006(2)S CWR11DH475(1)(2) 0.5 6.0 5.5
6.8 B T492B685(1)006(2)S CWR11DH685(1)(2) 0.5 6.0 4.5
10.0 B T492B106(1)006(2)S CWR11DH106(1)(2) 0.6 6.0 3.5
15.0 C T492C156(1)006(2)S CWR11DH156(1)(2) 0.9 6.0 3.0
22.0 C T492C226(1)006(2)S CWR11DH226(1)(2) 1.4 6.0 2.2
47.0 D T492D476(1)006(2)S CWR11DH476(1)(2) 2.8 6.0 1.1
10 Volt Rating at +85C (7 Volt Rating at 125C)
1.0 A T492A105(1)010(2)S CWR11FH105(1)(2) 0.5 4.0 10.0
1.5 A T492A155(1)010(2)S CWR11FH155(1)(2) 0.5 6.0 8.0
2.2 A T492A225(1)010(2)S CWR11FH225(1)(2) 0.5 6.0 8.0
3.3 B T492B335(1)010(2)S CWR11FH335(1)(2) 0.5 6.0 5.5
4.7 B T492B475(1)010(2)S CWR11FH475(1)(2) 0.5 6.0 4.5
6.8 B T492B685(1)010(2)S CWR11FH685(1)(2) 0.7 6.0 3.5 CONSTRUCTION
15.0 C T492C156(1)010(2)S CWR11FH156(1)(2) 1.5 6.0 2.5
Negative Silver Adhesive Polarity
33.0 D T492D336(1)010(2)S CWR11FH336(1)(2) 3.3 6.0 1.1 Termination* Washer Stripe (+)
Molded Polarity
15 Volt Rating at +85C (10 Volt Rating at +125C) Case Bevel (+)
0.68 A T492A684(1)015(2)S CWR11HH684(1)(2) 0.5 4.0 12.0 Tantalum
Wire
1.0 A T492A105(1)015(2)S CWR11HH105(1)(2) 0.5 4.0 10.0
1.5 A T492A155(1)015(2)S CWR11HH155(1)(2) 0.5 6.0 8.0
2.2 B T492B225(1)015(2)S CWR11HH225(1)(2) 0.5 6.0 5.5
3.3 B T492B335(1)015(2)S CWR11HH335(1)(2) 0.5 6.0 5.0
4.7 B T492B475(1)015(2)S CWR11HH475(1)(2) 0.7 6.0 4.0
Tantalum
Weld
10.0 C T492C106(1)015(2)S CWR11HH106(1)(2) 1.6 6.0 2.5 (Ta2O5)

Mn02 Coat
22.0 D T492D226(1)015(2)S CWR11HH226(1)(2) 3.3 6.0 1.1 (First Layer)
Carbon
20 Volt Rating at +85C (13 Volt Rating at +125C) (Second Layer)
Positive
Silver Paint Termination*
0.47 A T492A474(1)020(2)S CWR11JH474(1)(2) 0.5 4.0 14.0 (Third Layer)
*100% tin
0.68 A T492A684(1)020(2)S CWR11JH684(1)(2) 0.5 4.0 12.0
1.0 A T492A105(1)020(2)S CWR11JH105(1)(2) 0.5 4.0 10.0
1.5 B T492B155(1)020(2)S CWR11JH155(1)(2) 0.5 6.0 6.0
2.2 B T492B225(1)020(2)S CWR11JH225(1)(2) 0.5 6.0 5.0 CAPACITOR MARKINGS
3.3 B T492B335(1)020(2)S CWR11JH335(1)(2) 0.7 6.0 4.0
4.7 C T492C475(1)020(2)S CWR11JH475(1)(2) 1.0 6.0 3.0 T492 Series — All Case Sizes
6.8 C T492C685(1)020(2)S CWR11JH685(1)(2) 1.4 6.0 2.4
15.0 D T492D156(1)020(2)S CWR11JH156(1)(2) 3.0 6.0 1.1

0.33 A
25 Volt Rating at +85C (17 Volt Rating at +125C)
T492A334(1)025(2)S CWR11KH334(1)(2) 0.5 4.0 15.0
Jan
Brand J Polarity
Indicator (+)
0.47 A T492A474(1)025(2)S CWR11KH474(1)(2) 0.5 4.0 14.0 Picofarad
0.68
1.0
B
B
T492B684(1)025(2)S CWR11KH684(1)(2)
T492B105(1)025(2)S CWR11KH105(1)(2)
0.5
0.5
4.0
4.0
7.5
6.5
156 Code

1.5
2.2
B
C
T492B155(1)025(2)S CWR11KH155(1)(2)
T492C225(1)025(2)S CWR11KH225(1)(2)
0.5
0.6
6.0
6.0
6.5
3.5
Rated
Voltage 20K KEMET
I. D. Symbol
3.3
4.7
C
C
T492C335(1)025(2)S CWR11KH335(1)(2)
T492C475(1)025(2)S CWR11KH475(1)(2)
0.9
1.2
6.0
6.0
3.5
2.5 413
6.8 D T492D685(1)025(2)S CWR11KH685(1)(2) 1.7 6.0 1.4
10.0 D T492D106(1)025(2)S CWR11KH106(1)(2) 2.5 6.0 1.2 Print Week Code:
35 Volt Rating at +85C (23 Volt Rating at +125C) 1st Digit = Year
0.10 A T492A104(1)035(2)S CWR11MH104(1)(2) 0.5 4.0 24.0 2nd & 3rd Digits = Week
"413" = The 13th week of 2004
0.15 A T492A154(1)035(2)S CWR11MH154(1)(2) 0.5 4.0 21.0
0.22 A T492A224(1)035(2)S CWR11MH224(1)(2) 0.5 4.0 18.0
0.33 A T492A334(1)035(2)S CWR11MH334(1)(2) 0.5 4.0 15.0 Note on Failure Rates:
Exponential failure rate
0.47 B T492B474(1)035(2)S CWR11MH474(1)(2) 0.5 4.0 10.0 levels M, P, R and S are
0.68 B T492B684(1)035(2)S CWR11MH684(1)(2) 0.5 4.0 8.0 inactive for new design
1.0 B T492B105(1)035(2)S CWR11MH105(1)(2) 0.5 4.0 6.5 per MIL-C-55365. Parts
1.5 C T492C155(1)035(2)S CWR11MH155(1)(2) 0.5 6.0 4.5 qualified to Weibull failure
rate levels are substitutable
2.2 C T492C225(1)035(2)S CWR11MH225(1)(2) 0.8 6.0 3.5 for exponential failure
3.3 C T492C335(1)035(2)S CWR11MH335(1)(2) 1.2 6.0 2.5 rate levels.
4.7 D T492D475(1)035(2)S CWR11MH475(1)(2) 1.7 6.0 1.5 Note: ESR limits are per
Mil-C-55365/8
To complete Part Numbers:
(1) Insert “M” for ±20% tolerance, “K” for ±10% tolerance or “J” for ±5% tolerance.
(2) Insert Failure Rate Symbol: B (0.1%/1000 hours), C (0.01%/1000 hours) or
D (0.001%/1000 hours).

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 21
 SOLID TANTALUM CHIP CAPACITORS
T493 SERIES—Military COTS

Features
FEATURES
• Standard Cases Sizes A - X per EIA535BAAC
• Termination Finishes offered per MIL-PRF-55365: Gold Plated, Hot Solder Dipped, Solder Plated,
Solder Fused
• Weibull Grading Available: B (0.1%/1000hrs) and C (0.01%/1000hrs)
• Surge Current Testing Available per MIL-PRF-55365: 10 cycles @ +25°C; 10 cycles @ -55°C and +85°C
• Standard and Low ESR Options
• Operating Temperature Range: -55°C to +125°C
• Capacitance: 0.1 to 330µF
• Voltage: 4 to 50 Volts

OUTLINE
Outline DRAWING
Drawing
CATHODE (-) END SIDE VIEW ANODE (+) END BOTTOM VIEW
VIEW VIEW
B
W
B

H E F
K T

A
X S G S Termination Notch L
at KEMET’s Option,
Either End

DIMENSIONS-
Dimensions MILLIMETERS (INCHES)
- Millimeters (Inches)
Case Size ±0.20 ±0.1 ±0.3 B ±0.15
KEMET EIA/IECQ L W H K ±(.008) F ±(.004) S ±(.012) (Ref) ±.006 X(Ref) T(Ref) A(Min) G(ref) E(ref)

A 3216-18 3.2 ± 0.2 1.6 ± 0.2 1.6 ± 0.2 0.9 1.2 0.8 0.4 0.10 ± 0.10 0.13 0.8 1.1 1.3
(.126 ± .008) (.063 ± .008) (.063 ± .008) (.035) (.047) (.031) (.016) (.004 ± .004) (.005) (.031) (.043) (.051)
B 3528-21 3.5 ± 0.2 2.8 ± 0.2 1.9 ± 0.2 1.1 2.2 0.8 0.4 0.10 ± 0.10 0.13 1.1 1.8 2.2
(.138 ± .008) (.110 ± .008) (.075 ± .008) (.043) (.087) (.031) (.016) (.004 ± .004) (.005) (.043) (.071) (.087)
C 6032-28 6.0 ± 0.3 3.2 ± 0.3 2.5 ± 0.3 1.4 2.2 1.3 0.5 0.10 ± 0.10 0.13 2.5 2.8 2.4
(.236 ± .012) (.126 ± .012) (.098 ± .012) (.055) (.087) (.051) (.020) (.004 ± .004) (.005) (.098) (.110) (.094)
D 7343-31 7.3 ± 0.3 4.3 ± 0.3 2.8 ± 0.3 1.5 2.4 1.3 0.5 0.10 ± 0.10 0.13 3.8 3.5 3.5
(.287 ± .012) (.169 ± .012) (.110 ± .012) (.059) (.094) (.051) (.020) (.004 ± .004) (.005) (.150) (.138) (.138)
X 7343-43 7.3 ± 0.3 4.3 ± 0.3 4.0 ± 0.3 2.3 2.4 1.3 0.5 0.10 ± 0.10 0.13 3.8 3.5** 3.5**
(.287 ± 0.12) (.169 ± .012) (.157 ± .012) (.091) (.094) (.051) (.020) (.004 ± .004) (.005) (.150) (.138) (.138)
Notes: 1. Metric dimensions govern.
2. (ref) - Dimensions provided for reference only.
**Round Glue Pad: 2.9 ±0.1mm (0.114 ±.004”) in diameter at KEMET’s option.

COMPONENT
ComponentMARKING
Marking

(+) KEMET Polarity

T493 COTS + Indicator

336 Picofarad Code

Rated
Voltage 20 K KEMET ID

315
415 Print Week Code
1st Digit = Year
2nd & 3rd Digit + Week
“315”==15th
“415 15th week
Weekof
of 2004
2003

22 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 SOLID TANTALUM CHIP CAPACITORS
T493 SERIES—Military COTS
ORDERING INFORMATION
Ordering Information
T 493 D 227 K 006 C H 6XXX

Tantalum ESR/Surge Designator

6110 Surge = None
Series ESR = Standard
T493 Military Commercial Off-The-Shelf 6120 Surge = None
Case Size ESR = Low
A, B, C, D, X 6210 Surge = 10 Cycles, +25ºC
ESR = Standard
Capacitance Picofarad Code 6220 Surge + 10 Cycles, +25ºC
First two digits represent significant figures. ESR = Low
Third digit specifies number of zeros to follow. 6410 Surge = 10 Cycles, -55ºC and +85ºC

Solid Tantalum Surface Mount

ESR = Standard
Capacitance Tolerances 6420 Surge = 10 Cycles, -55ºC and +85ºC
M = ±10% ESR = Low
K = ±10% Note: For order entry purposes the last 4-digits
of the part number will be entered in the
J = ±5% (For 5% tolerance contact KEMET sales rep.) KEMET Customer Specification (C-Spec)Field.
Voltage Termination Finish
As shown B - Gold plated
Reliability Level C - Hot solder dipped
A - Non-ER H - Solder plated
B - 0.1%/K hrs. K - Solder fused
C - 0.01%/K hrs.

T493 RATINGS AND PART NUMBER REFERENCE

Std. ESR Low ESR
DCL DF %
Capaci- Ohms Ohms
Case KEMET µA @ @ +25ºC
tance @+25°C @+25°C
Size Part Number 25ºC 120 Hz
µF 100 kHz 100 kHz
Max Max
Max Max
4 Volt Rating at +85ºC (2.7 Volt Rating at +125ºC)
2.2 A T493A225(1)004(2)(3)(4)(5) 0.5 6.0 8.0 6.0
3.3 A T493A335(1)004(2)(3)(4)(5) 0.5 6.0 8.0 4.0
4.7 A T493A475(1)004(2)(3)(4)(5) 0.5 6.0 8.0 3.5
6.8 A T493A685(1)004(2)(3)(4)(5) 0.5 6.0 6.0 3.0
6.8 B T493B685(1)004(2)(3)(4)(5) 0.5 6.0 5.5 2.0
10.0 A T493A106(1)004(2)(3)(4)(5) 0.5 6.0 6.0 2.0
10.0 B T493B106(1)004(2)(3)(4)(5) 0.5 6.0 3.5 1.2
15.0 A T493A156(1)004(2)(3)(4)(5) 0.6 6.0 4.0 1.5
15.0 B T493B156(1)004(2)(3)(4)(5) 0.6 6.0 3.5 1.2
22.0 A T493A226(1)004(2)(3)(4)(5) 0.9 6.0 4.0 1.5
22.0 B T493B226(1)004(2)(3)(4)(5) 0.9 6.0 3.5 0.6
22.0 C T493C226(1)004(2)(3)(4)(5) 0.9 6.0 1.8 0.5
33.0 A T493A336(1)004(2)(3)(4)(5) 1.3 6.0 4.0 3.0
33.0 B T493B336(1)004(2)(3)(4)(5) 1.3 6.0 3.5 0.5
33.0 C T493C336(1)004(2)(3)(4)(5) 1.3 6.0 1.8 0.5
47.0 B T493B476(1)004(2)(3)(4)(5) 1.9 6.0 3.0 0.5
47.0 C T493C476(1)004(2)(3)(4)(5) 1.9 6.0 1.8 0.5
68.0 B T493B686(1)004(2)(3)(4)(5) 2.7 6.0 3.5 2.0
68.0 C T493C686(1)004(2)(3)(4)(5) 2.7 6.0 1.6 0.25
68.0 D T493D686(1)004(2)(3)(4)(5) 2.7 6.0 0.8 0.2
100.0 B T493B107(1)004(2)(3)(4)(5) 4.0 8.0 1.0 0.7
100.0 C T493C107(1)004(2)(3)(4)(5) 4.0 8.0 1.2 0.2
100.0 D T493D107(1)004(2)(3)(4)(5) 4.0 8.0 0.8 0.2
150.0 C T493C157(1)004(2)(3)(4)(5) 6.0 8.0 1.2 0.3
150.0 D T493D157(1)004(2)(3)(4)(5) 6.0 8.0 0.8 0.15
220.0 D T493D227(1)004(2)(3)(4)(5) 8.8 8.0 0.9 0.7
330.0 D T493D337(1)004(2)(3)(4)(5) 13.2 8.0 0.7 0.15
330.0 X T493X337(1)004(2)(3)(4)(5) 13.2 8.0 0.5 0.2
6 Volt Rating at +85ºC (4 Volt Rating at +125ºC)
1.5 A T493A155(1)006(2)(3)(4(5) 0.5 6.0 8.0 6.0
2.2 A T493A225(1)006(2)(3)(4)(5) 0.5 6.0 8.0 6.0
3.3 A T493A335(1)006(2)(3)(4)(5) 0.5 6.0 8.0 6.0
4.7 A T493A475(1)006(2)(3)(4)(5) 0.5 6.0 6.0 3.5
4.7 B T493B475(1)006(2)(3)(4)(5) 0.5 6.0 5.5 3.5
6.8 A T493A685(1)006(2)(3)(4)(5) 0.5 6.0 6.0 2.0
6.8 B T493B685(1)006(2)(3)(4)(5) 0.5 6.0 3.5 1.2
10.0 A T493A106(1)006(2)(3)(4)(5) 0.6 6.0 4.0 2.0
10.0 B T493B106(1)006(2)(3)(4)(5) 0.6 6.0 3.5 1.0
15.0 A T493A156(1)006(2)(3)(4)(5) 0.9 6.0 4.0 1.5
15.0 B T493B156(1)006(2)(3)(4)(5) 0.9 6.0 3.5 0.7
15.0 C T493C156(1)006(2)(3)(4)(5) 0.9 6.0 1.8 0.6
22.0 A T493A226(1)006(2)(3)(4)(5) 1.4 6.0 4.0 3.0
22.0 B T493B226(1)006(2)(3)(4)(5) 1.4 6.0 3.5 0.6
(1) To complete KEMET part number, insert M for ±20% or K for ±10% capacitance tolerance. To request ±5%
tolerance,contact KEMET sales representative.
(2) To complete KEMET part number, insert A for Non-ER; B for 0.1%/1000 Hrs.; or C for 0.01%/1000 Hrs. Reliability Level.
(3) To complete KEMET part number, insert B for Gold Plated (50 µ inch minimum); C for Hot Solder Dipped (60 µ inch
minimum); H for Solder Plated (100 µ inch minimum); or K for Solder Fused (60 µ inch minimum Termination Finish.
(4) To complete KEMET part number for Surge Current testing, insert 61 for none; 62 for 10 cycles +25°C; or 64 for 10
cycles, -55°C & +85°C.
(5) To complete KEMET part number, insert 10 for Standard ESR; or 20 for Low ESR Option.

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 23
 SOLID TANTALUM CHIP CAPACITORS
T493 SERIES—Military COTS

T493 RATINGS AND PART NUMBER REFERENCE

Std. ESR Low ESR
DCL DF %
Capaci- Ohms Ohms
Case KEMET µA @ @ +25ºC
tance @+25°C @+25°C
Size Part Number 25ºC 120 Hz
µF 100 kHz 100 kHz
Max Max
Max Max
6 Volt Rating at +85ºC (4 Volt Rating at +125ºC) (con't)
22.0 C T493C226(1)006(2)(3)(4)(5) 1.4 6.0 1.8 0.5
33.0 B T493B336(1)006(2)(3)(4)(5) 2.0 6.0 3.0 0.6
33.0 C T493C336(1)006(2)(3)(4)(5) 2.0 6.0 1.8 0.3
47.0 B T493B476(1)006(2)(3)(4)(5) 2.9 6.0 3.5 2.0
47.0 C T493C476(1)006(2)(3)(4)(5) 2.9 6.0 1.6 0.25
47.0 D T493D476(1)006(2)(3)(4)(5) 2.9 6.0 0.8 0.22
68.0 B T493B686(1)006(2)(3)(4)(5) 4.1 8.0 1.0 0.65
68.0 C T493C686(1)006(2)(3)(4)(5) 4.1 6.0 1.2 0.2
68.0 D T493D686(1)006(2)(3)(4)(5) 4.1 6.0 0.8 0.2
100.0 B T493B107(1)006(2)(3)(4)(5) 6.3 15.0 10.0 8.0
100.0 C T493C107(1)006(2)(3)(4)(5) 6.0 8.0 1.2 0.15
100.0 D T493D107(1)006(2)(3)(4)(5) 6.0 8.0 0.8 0.15
150.0 C T493C157(1)006(2)(3)(4)(5) 9.0 8.0 1.2 0.3
150.0 D T493D157(1)006(2)(3)(4)(5) 9.0 8.0 0.7 0.15
220.0 C T493C227(1)006(2)(3)(4)(5) 13.2 10.0 1.2 0.3
220.0 D T493D227(1)006(2)(3)(4)(5) 13.2 8.0 0.7 0.1
220.0 X T493X227(1)006(2)(3)(4)(5) 13.2 8.0 0.7 0.15
10 Volt Rating at +85ºC (7 Volt Rating at +125ºC)
1.0 A T493A105(1)010(2)(3)(4)(5) 0.5 4.0 10.0 6.0
1.5 A T493A155(1)010(2)(3)(4)(5) 0.5 6.0 8.0 6.0
2.2 A T493A225(1)010(2)(3)(4)(5) 0.5 6.0 8.0 6.0
3.3 A T493A335(1)010(2)(3)(4)(5) 0.5 6.0 6.0 4.0
3.3 B T493B335(1)010(2)(3)(4)(5) 0.5 6.0 5.5 3.5
4.7 A T493A475(1)010(2)(3)(4)(5) 0.5 6.0 6.0 3.0
4.7 B T493B475(1)010(2)(3)(4)(5) 0.5 6.0 3.5 1.5
6.8 A T493A685(1)010(2)(3)(4)(5) 0.7 6.0 6.0 3.0
6.8 B T493B685(1)010(2)(3)(4)(5) 0.7 6.0 3.5 1.2
10.0 A T493A106(1)010(2)(3)(4)(5) 1.0 6.0 4.0 1.8
10.0 B T493B106(1)010(2)(3)(4)(5) 1.0 6.0 3.5 0.8
10.0 C T493C106(1)010(2)(3)(4)(5) 1.0 6.0 1.8 0.6
15.0 A T493A156(1)010(2)(3)(4)(5) 1.5 8.0 6.0 4.0
15.0 B T493B156(1)010(2)(3)(4)(5) 1.5 6.0 3.5 0.7
15.0 C T493C156(1)010(2)(3)(4)(5) 1.5 6.0 1.8 0.5
22.0 B T493B226(1)010(2)(3)(4)(5) 2.2 6.0 3.0 0.7
22.0 C T493C226(1)010(2)(3)(4)(5) 2.2 6.0 1.8 0.4
33.0 B T493B336(1)010(2)(3)(4)(5) 3.3 6.0 3.5 2.0
33.0 C T493C336(1)010(2)(3)(4)(5) 3.3 6.0 1.6 0.3
33.0 D T493D336(1)010(2)(3)(4)(5) 3.3 6.0 0.8 0.3
47.0 C T493C476(1)010(2)(3)(4)(5) 4.7 6.0 1.2 0.3
47.0 D T493D476(1)010(2)(3)(4)(5) 4.7 6.0 0.8 0.2
68.0 C T493C686(1)010(2)(3)(4)(5) 6.8 6.0 1.2 0.3
68.0 D T493D686(1)010(2)(3)(4)(5) 6.8 6.0 0.8 0.2
68.0 X T493X686(1)010(2)(3)(4)(5) 5.4 4.0 0.5 0.15
100.0 C T493C107(1)010(2)(3)(4)(5) 10.0 8.0 1.2 0.3
100.0 D T493D107(1)010(2)(3)(4)(5) 10.0 8.0 0.7 0.1
150.0 D T493D157(1)010(2)(3)(4)(5) 15.0 8.0 0.7 0.1
150.0 X T493X157(1)010(2)(3)(4)(5) 15.0 8.0 0.7 0.2
220.0 D T493D227(1)010(2)(3)(4)(5) 22.0 8.0 0.5 0.2
220.0 X T493X227(1)010(2)(3)(4)(5) 22.0 8.0 0.5 0.1
330.0 X T493X337(1)010(2)(3)(4)(5) 33.0 10.0 0.5 0.1
16 Volt Rating at +85ºC (10 Volt Rating at +125ºC)
0.68 A T493A684(1)016(2)(3)(4)(5) 1.1 6.0 12.0 8.0
1.0 A T493A105(1)016(2)(3)(4)(5) 0.5 4.0 10.0 6.0
1.5 A T493A155(1)016(2)(3)(4)(5) 0.5 6.0 8.0 6.0
2.2 A T493A225(1)016(2)(3)(4)(5) 0.5 6.0 6.0 4.0
3.3 A T493A335(1)016(2)(3)(4)(5) 0.5 6.0 6.0 3.5
3.3 B T493B335(1)016(2)(3)(4)(5) 0.5 6.0 3.5 2.0
4.7 A T493A475(1)016(2)(3)(4)(5) 0.8 6.0 6.0 3.0
4.7 B T493B475(1)016(2)(3)(4)(5) 0.8 6.0 3.5 1.5
6.8 A T493A685(1)016(2)(3)(4)(5) 1.1 6.0 7.0 3.0
6.8 B T493B685(1)016(2)(3)(4)(5) 1.1 6.0 3.5 1.2
6.8 C T493C685(1)016(2)(3)(4)(5) 1.1 6.0 1.9 0.8
10.0 B T493B106(1)016(2)(3)(4)(5) 1.6 6.0 3.5 0.8
10.0 C T493C106(1)016(2)(3)(4)(5) 1.6 6.0 1.8 0.6
15.0 B T493B156(1)016(2)(3)(4)(5) 2.4 6.0 3.0 0.8
15.0 C T493C156(1)016(2)(3)(4)(5) 2.4 6.0 1.8 0.4
22.0 B T493B226(1)016(2)(3)(4)(5) 3.5 6.0 2.2 0.8
22.0 C T493C226(1)016(2)(3)(4)(5) 3.6 6.0 1.6 0.4
22.0 D T493D226(1)016(2)(3)(4)(5) 3.6 6.0 0.8 0.3
(1) To complete KEMET part number, insert M for ±20% or K for ±10% capacitance tolerance. To request ±5%
tolerance,contact KEMET sales representative.
(2) To complete KEMET part number, insert A for Non-ER; B for 0.1%/1000 Hrs.; or C for 0.01%/1000 Hrs. Reliability Level.
(3) To complete KEMET part number, insert B for Gold Plated (50 µ inch minimum); C for Hot Solder Dipped (60 µ inch
minimum); H for Solder Plated (100 µ inch minimum); or K for Solder Fused (60 µ inch minimum Termination Finish.
(4) To complete KEMET part number for Surge Current testing, insert 61 for none; 62 for 10 cycles +25°C; or 64 for 10
cycles, -55°C & +85°C.
(5) To complete KEMET part number, insert 10 for Standard ESR; or 20 for Low ESR Option.

24 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 SOLID TANTALUM CHIP CAPACITORS
T493 SERIES—Military COTS

T493 RATINGS AND PART NUMBER REFERENCE

Std. ESR Low ESR
DCL DF %
Capaci- Ohms Ohms
Case KEMET µA @ @ +25ºC
tance @+25°C @+25°C
Size Part Number 25ºC 120 Hz
µF 100 kHz 100 kHz
Max Max
Max Max
16 Volt Rating at +85ºC (10 Volt Rating at +125ºC) cont.
33.0 C T493C336(1)016(2)(3)(4)(5) 5.3 6.0 1.2 0.3
33.0 D T493D336(1)016(2)(3)(4)(5) 5.3 6.0 0.8 0.25
33.0 D T493D336(1)016(2)(3)(4)(5) 5.3 6.0 0.8 0.3
47.0 C T493C476(1)016(2)(3)(4)(5) 7.5 6.0 1.2 0.5

Solid Tantalum Surface Mount

47.0 D T493D476(1)016(2)(3)(4)(5) 7.5 6.0 0.8 0.2
68.0 D T493D686(1)016(2)(3)(4)(5) 10.9 6.0 0.7 0.2
100.0 D T493D107(1)016(2)(3)(4)(5) 16.0 8.0 0.7 0.125
100.0 X T493X107(1)016(2)(3)(4)(5) 16.0 8.0 0.7 0.1
150.0 X T493X157(1)016(2)(3)(4)(5) 24.0 8.0 0.5 0.2
20 Volt Rating at +85ºC (13 Volt Rating at +125ºC)
0.47 A T493A474(1)020(2)(3)(4)(5) 0.5 4.0 14.0 9.0
0.68 A T493A684(1)020(2)(3)(4)(5) 0.5 4.0 12.0 8.0
1.0 A T493A105(1)020(2)(3)(4)(5) 0.5 4.0 10.0 5.5
1.5 A T493A155(1)020(2)(3)(4)(5) 0.5 6.0 8.0 4.5
1.5 B T493B155(1)020(2)(3)(4)(5) 0.5 6.0 6.0 4.0
2.2 A T493A225(1)020(2)(3)(4)(5) 0.5 6.0 7.0 4.0
2.2 B T493B225(1)020(2)(3)(4)(5) 0.5 6.0 3.5 1.5
3.3 A T493A335(1)020(2)(3)(4)(5) 0.7 6.0 7.0 4.0
3.3 B T493B335(1)020(2)(3)(4)(5) 0.7 6.0 3.5 1.3
4.7 A T493A475(1)020(2)(3)(4)(5) 1.0 8.0 6.0 1.8
4.7 B T493B475(1)020(2)(3)(4)(5) 1.0 6.0 3.5 1.0
4.7 C T493C475(1)020(2)(3)(4)(5) 1.0 6.0 2.4 0.6
6.8 B T493B685(1)020(2)(3)(4)(5) 1.4 6.0 3.5 1.0
6.8 C T493C685(1)020(2)(3)(4)(5) 1.4 6.0 1.9 0.6
10.0 B T493B106(1)020(2)(3)(4)(5) 2.0 6.0 3.0 1.0
10.0 C T493C106(1)020(2)(3)(4)(5) 2.0 6.0 1.8 0.5
15.0 C T493C156(1)020(2)(3)(4)(5) 3.0 6.0 1.7 0.4
15.0 D T493D156(1)020(2)(3)(4)(5) 3.0 6.0 1.0 0.35
22.0 C T493C226(1)020(2)(3)(4)(5) 4.4 6.0 1.2 0.4
22.0 D T493D226(1)020(2)(3)(4)(5) 4.4 6.0 0.8 0.3
33.0 D T493D336(1)020(2)(3)(4)(5) 6.6 6.0 0.8 0.2
47.0 D T493D476(1)020(2)(3)(4)(5) 9.4 6.0 0.7 0.2
47.0 X T493X476(1)020(2)(3)(4)(5) 7.5 4.0 0.7 0.15
68.0 D T493D686(1)020(2)(3)(4)(5) 13.6 8.0 0.7 0.2
68.0 X T493X686(1)020(2)(3)(4)(5) 13.6 6.0 0.7 0.15
25 Volt Rating at +85ºC (17 Volt Rating at +125ºC)
0.33 A T493A334(1)025(2)(3)(4)(5) 0.5 4.0 15.0 10.0
0.47 A T493A474(1)025(2)(3)(4)(5) 0.5 4.0 14.0 9.0
0.68 A T493A684(1)025(2)(3)(4)(5) 0.5 4.0 10.0 6.0
0.68 B T493B684(1)025(2)(3)(4)(5) 0.5 4.0 7.5 5.5
1.0 A T493A105(1)025(2)(3)(4)(5) 0.5 4.0 8.0 4.0
1.0 B T493B105(1)025(2)(3)(4)(5) 0.5 4.0 5.0 2.0
1.5 A T493A155(1)025(2)(3)(4)(5) 0.5 6.0 10.0 3.0
1.5 B T493B155(1)025(2)(3)(4)(5) 0.5 6.0 5.0 1.5
2.2 B T493B225(1)025(2)(3)(4)(5) 0.6 6.0 4.5 1.2
2.2 C T493C225(1)025(2)(3)(4)(5) 0.6 6.0 3.5 2.2
3.3 B T493B335(1)025(2)(3)(4)(5) 0.9 6.0 3.5 2.0
3.3 C T493C335(1)025(2)(3)(4)(5) 0.9 6.0 2.5 1.2
4.7 B T493B475(1)025(2)(3)(4)(5) 1.2 6.0 1.5 1.0
4.7 C T493C475(1)025(2)(3)(4)(5) 1.2 6.0 2.4 0.6
6.8 C T493C685(1)025(2)(3)(4)(5) 1.7 6.0 1.9 0.6
6.8 D T493D685(1)025(2)(3)(4)(5) 1.7 6.0 1.4 1.0
10.0 C T493C106(1)025(2)(3)(4)(5) 2.5 6.0 1.5 0.5
10.0 D T493D106(1)025(2)(3)(4)(5) 2.5 6.0 1.0 0.4
15.0 C T493C156(1)025(2)(3)(4)(5) 3.8 6.0 1.5 0.9
15.0 D T493D156(1)025(2)(3)(4)(5) 3.8 6.0 1.0 0.35
15.0 X T493X156(1)025(2)(3)(4)(5) 3.0 6.0 0.7 0.2
22.0 D T493D226(1)025(2)(3)(4)(5) 5.5 6.0 0.8 0.2
22.0 X T493X226(1)025(2)(3)(4)(5) 4.4 4.0 0.7 0.23
33.0 X T493X336(1)025(2)(3)(4)(5) 8.3 6.0 0.7 0.3
47.0 X T493X476(1)025(2)(3)(4)(5) 11.8 6.0 0.7 0.3

(1) To complete KEMET part number, insert M for ±20% or K for ±10% capacitance tolerance. To request ±5%
tolerance,contact KEMET sales representative.
(2) To complete KEMET part number, insert A for Non-ER; B for 0.1%/1000 Hrs.; or C for 0.01%/1000 Hrs. Reliability Level.
(3) To complete KEMET part number, insert B for Gold Plated (50 µ inch minimum); C for Hot Solder Dipped (60 µ inch
minimum); H for Solder Plated (100 µ inch minimum); or K for Solder Fused (60 µ inch minimum Termination Finish.
(4) To complete KEMET part number for Surge Current testing, insert 61 for none; 62 for 10 cycles +25°C; or 64 for 10
cycles, -55°C & +85°C.
(5) To complete KEMET part number, insert 10 for Standard ESR; or 20 for Low ESR Option.

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 25
 SOLID TANTALUM CHIP CAPACITORS
T493 SERIES—Military COTS
T493 RATINGS AND PART NUMBER REFERENCE
Std. ESR Low ESR
DCL DF %
Capaci- Ohms Ohms
Case KEMET µA @ @ +25ºC
tance @+25°C @+25°C
Size Part Number 25ºC 120 Hz
µF 100 kHz 100 kHz
Max Max
Max Max
35 Volt Rating at +85ºC (23 Volt Rating at +125ºC)
0.10 A T493A104(1)035(2)(3)(4)(5) 0.5 4.0 20.0 10.0
0.15 A T493A154(1)035(2)(3)(4)(5) 0.5 4.0 19.0 6.0
0.22 A T493A224(1)035(2)(3)(4)(5) 0.5 4.0 18.0 6.0
0.33 A T493A334(1)035(2)(3)(4)(5) 0.5 4.0 15.0 6.0
0.47 A T493A474(1)035(2)(3)(4)(5) 0.5 4.0 14.0 4.0
0.47 B T493B474(1)035(2)(3)(4)(5) 0.5 4.0 8.0 2.5
0.68 A T493A684(1)035(2)(3)(4)(5) 0.5 4.0 10.0 6.0
0.68 B T493B684(1)035(2)(3)(4)(5) 0.5 4.0 6.5 2.5
1.0 A T493A105(1)035(2)(3)(4)(5) 0.5 4.0 10.0 6.0
1.0 B T493B105(1)035(2)(3)(4)(5) 0.5 4.0 5.0 2.0
1.5 B T493B155(1)035(2)(3)(4)(5) 0.5 6.0 5.0 3.0
1.5 C T493C155(1)035(2)(3)(4)(5) 0.5 6.0 4.5 2.5
2.2 B T493B225(1)035(2)(3)(4)(5) 0.8 6.0 4.0 2.5
2.2 C T493C225(1)035(2)(3)(4)(5) 0.8 6.0 3.5 1.5
3.3 B T493B335(1)035(2)(3)(4)(5) 1.2 6.0 3.5 1.3
3.3 C T493C335(1)035(2)(3)(4)(5) 1.2 6.0 2.5 0.8
4.7 C T493C475(1)035(2)(3)(4)(5) 1.7 6.0 2.5 0.6
4.7 D T493D475(1)035(2)(3)(4)(5) 1.7 6.0 1.5 0.7
6.8 C T493C685(1)035(2)(3)(4)(5) 2.4 6.0 2.0 0.9
6.8 D T493D685(1)035(2)(3)(4)(5) 2.4 6.0 1.3 0.5
10.0 C T493C106(1)035(2)(3)(4)(5) 3.5 6.0 2.0 1.2
10.0 D T493D106(1)035(2)(3)(4)(5) 3.5 6.0 1.0 0.3
10.0 X T493X106(1)035(2)(3)(4)(5) 2.8 4.0 0.9 0.25
15.0 D T493D156(1)035(2)(3)(4)(5) 5.3 6.0 0.8 0.3
15.0 X T493X156(1)035(2)(3)(4)(5) 5.3 6.0 0.9 0.3
22.0 D T493D226(1)035(2)(3)(4)(5) 7.7 6.0 0.7 0.4
22.0 X T493X226(1)035(2)(3)(4)(5) 7.7 6.0 0.7 0.3
33.0 X T493X336(1)035(2)(3)(4)(5) 11.6 6.0 0.6 0.3
50 Volt Rating at +85ºC (33 Volt Rating at +125ºC)
0.10 A T493A104(1)050(2)(3)(4)(5) 0.5 4.0 20.0 10.0
0.15 A T493A154(1)050(2)(3)(4)(5) 0.5 4.0 19.0 10.0
0.15 B T493B154(1)050(2)(3)(4)(5) 0.5 4.0 16.0 10.0
0.22 B T493B224(1)050(2)(3)(4)(5) 0.5 4.0 14.0 10.0
0.33 B T493B334(1)050(2)(3)(4)(5) 0.5 4.0 10.0 2.5
0.47 B T493B474(1)050(2)(3)(4)(5) 0.5 4.0 9.0 2.0
0.47 C T493C474(1)050(2)(3)(4)(5) 0.5 4.0 8.0 1.8
0.68 C T493C684(1)050(2)(3)(4)(5) 0.5 4.0 7.0 1.6
1.0 C T493C105(1)050(2)(3)(4)(5) 0.5 4.0 5.5 1.6
1.5 C T493C155(1)050(2)(3)(4)(5) 0.8 6.0 4.5 1.5
1.5 D T493D155(1)050(2)(3)(4)(5) 0.8 6.0 3.5 1.0
2.2 C T493C225(1)050(2)(3)(4)(5) 1.1 6.0 3.5 1.5
2.2 D T493D225(1)050(2)(3)(4)(5) 1.1 6.0 2.5 0.8
3.3 D T493D335(1)050(2)(3)(4)(5) 1.7 6.0 2.0 0.8
4.7 D T493D475(1)050(2)(3)(4)(5) 2.4 6.0 1.5 0.6
4.7 X T493X475(1)050(2)(3)(4)(5) 1.9 4.0 0.9 0.3
6.8 X T493X685(1)050(2)(3)(4)(5) 3.5 6.0 1.0 0.5

(1) To complete KEMET part number, insert M for ±20% or K for ±10% capacitance tolerance. To request ±5%
tolerance,contact KEMET sales representative.
(2) To complete KEMET part number, insert A for Non-ER; B for 0.1%/1000 Hrs.; or C for 0.01%/1000 Hrs. Reliability Level.
(3) To complete KEMET part number, insert B for Gold Plated (50 µ inch minimum); C for Hot Solder Dipped (60 µ inch
minimum); H for Solder Plated (100 µ inch minimum); or K for Solder Fused (60 µ inch minimum Termination Finish.
(4) To complete KEMET part number for Surge Current testing, insert 61 for none; 62 for 10 cycles +25°C; or 64 for 10
cycles, -55°C & +85°C.
(5) To complete KEMET part number, insert 10 for Standard ESR; or 20 for Low ESR Option.

26 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 SOLID TANTALUM CHIP CAPACITORS
T494 SERIES — Low ESR, Industrial Grade
FEATURES
• Low ESR values in EIA 535BAAC sizes • Tolerance: ±10%, ±20%
• Taped and Reeled per EIA 481-1 • Voltage: 3-50 VDC
• Symmetrical, Compliant Terminations • Extended Range Values
• Optional Gold-plated Terminations • Low Profile Case Sizes
• Laser-marked Case • RoHS Compliant & Leadfree Terminations
• 100% Surge Current test on C, D, E, U, V, X sizes (See www.kemet.com for lead transition)
• Capacitance: 0.1 F to 1000 F
CAPACITOR OUTLINE DRAWING

Solid Tantalum Surface Mount

CATHODE (-) END SIDE VIEW ANODE (+) END BOTTOM VIEW
VIEW VIEW
B
W
B

H E F
K T P

S S R Termination A
X G cutout at L
KEMET’s
Option,
either end

STANDARD T494 DIMENSIONS

Millimeters (inches)
CASE SIZE COMPONENT
KEMET EIA L* W* H* K* ±± 0.20
(.008) F*
± 0.1 ± 0.3 B ± 0.15
± (.004) S* ± (.012) (Ref) ± (.006)
X
(Ref)
P R T A G E
(Ref) (Ref) (Ref) (Min) (Ref) (Ref)
A 3216-18 3.2 ± 0.2 1.6 ±0.2 1.6 ± 0.2 0.9 1.2 0.8 0.4 0.10 ± 0.10 0.4 0.4 0.13 0.8 1.1 1.3
(.126 ± .008) (.063 ±.008) (.063 ± .008) (.035) (.047) (.031) (.016) (.004 ± .004) (.016) (.016) (.005) (.031) (.043) (.051)
B 3528-21 3.5 ± 0.2 2.8 ± 0.2 1.9 ± 0.2 1.1 2.2 0.8 0.4 0.10 ± 0.10 0.5 1.0 0.13 1.1 1.8 2.2
(.138 ± .008) (.110 ± .008) (.075 ± .008) (.043) (.087) (.031) (.016) (.004 ± .004) (.020) (.039) (.005) (.043) (.071) (.087)
C 6032-28 6.0 ± 0.3 3.2 ± 0.3 2.5 ± 0.3 1.4 2.2 1.3 0.5 0.10 ± 0.10 0.9 1.0 0.13 2.5 2.8 2.4
(.236 ± .012) (.126 ± .012) (.098 ± .012) (.055) (.087) (.051) (.020) (.004 ± .004) (.035) (.039) (.005) (.098) (.110) (.094)
D 7343-31 7.3 ± 0.3 4.3 ± 0.3 2.8 ± 0.3 1.5 2.4 1.3 0.5 0.10 ± 0.10 0.9 1.0 0.13 3.8 3.5 3.5
(.287 ± .012) (.169 ± .012) (.110 ± .012) (.059) (.094) (.051) (.020) (.004 ± .004) (.035) (.039) (.005) (.150) (.138) (.138)
X 7343-43 7.3 ± 0.3 4.3 ± 0.3 4.0 ± 0.3 2.3 2.4 1.3 0.5 0.10 ± 0.10 1.7 1.0 0.13 3.8 3.5** 3.5**
(.287 ± .012) (.169 ± .012) (.157 ± .012) (.091) (.094) (.051) (.020) (.004 ± .004) (.067) (.039) (.005) (.150) (.138) (.138)
E 7260-38 7.3 ± 0.3 6.0 ± 0.3 3.6 ± 0.2 2.3 4.1 1.3 0.5 0.10 ± 0.10 0.9 1.0 0.13 3.8 3.5 3.5
(.287 ± .012) (.236 ± .012) (.142 ± .008) (.091) (.161) (.051) (.020) (.004 ± .004) (.035) (.039) (.005) (.150) (.138) (.138)

Notes: 1. Metric dimensions govern.

2. (Ref) - Dimensions provided for reference only.
* Mil-C-55365/8 Specified Dimensions
** Round Glue Pad: 2.9 ±0.1mm (0.114" ± 0.004") in diameter at KEMET’s option

LOW PROFILE T494 DIMENSIONS

Millimeters (inches)
CASE SIZE COMPONENT
X T A G E
KEMET EIA L W H Max. K Min. F ± 0.1 S ± 0.3
(Ref (Ref) (Min) (Ref) (Ref)
2012-12 2.0 ± 0.2 1.3 ± 0.2 1.2 0.3 0.9 0.5 0.05 0.13 0.8 0.5 0.8
R
(.079 ± .008) (.051 ± .008) (.047) (.012) (.035) (.020) (.002) (.005) (.031) (.020) (.031)
3216-12 3.2 ± 0.2 1.6 ± 0.2 1.2 0.3 1.2 0.8 0.05 0.13 0.8 1.1 1.3
S
(.126 ± .008) (.063 ± .008) (.047) (.012) (.047) (.031) (.002) (.005) (.031) (.043) (.051)
3528-12 3.5 ± 0.2 2.8 ± 0.2 1.2 0.3 2.2 0.8 0.05 0.13 1.1 1.8 2.2
T
(.138 ± .008) (.110 ± .008) (.047) (.012) (.087) (.031) (.002) (.005) (.043) (.071) (.087)
6032-15 6.0 ± 0.3 3.2 ± 0.3) 1.5 0.5 2.2 1.3 0.05 0.13 2.5 2.8 2.4
U
(.236 ± .012) (.126 ± .012) (.059) (.020) (.087) (.051) (.002) (.005) (.098) (.110) (.094)
7343-20 7.3 ± 0.3 4.3 ± 0.3 2.0 0.9 2.4 1.3 0.05 0.13 3.8 3.5 3.5
V
(.287 ± .012) (.169 ± .012) (.079) (.035) (.094) (.051) (.002) (.005) (.150) (.138) (.138)
Notes: 1. Metric dimensions govern.
2. (Ref) - Dimensions provided for reference only.
3. No dimensions provided for B, P or R because low profile cases do not have a bevel or a notch.

T494 ORDERING INFORMATION

T 494 B 105 M 035 A S*
Lead Material
Tantalum S - 100% Tin (Sn) Plated
H - Standard Solder -Coated (90% Sn/10% Pb)
Series G - Gold Plated (A, B, C, D, X only)
T494 - Low ESR, Industrial Grade T - 100% Tin (Sn) Plated
Case Size Failure Rate
A, B, C, D, E, R, S, T, U, V, X A - Not Applicable
Capacitance Picofarad Code Voltage
First two digits represent significant figures.
Third digit specifies number of zeros to follow. Capacitance Tolerance
*Part number example: T494B105M035AS (14 digits - no spaces) M - ± 20%
See www.kemet.com for Pb Free transition K - ±10%

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 27
 SOLID TANTALUM CHIP CAPACITORS
T494 SERIES—Low ESR, Industrial Grade

T494 RATINGS & PART NUMBER REFERENCE

DC DF % ESR Ω DC DF % ESR Ω
Capaci- Capaci-
Case KEMET Leakage @ +25ºC @ +25ºC Case KEMET Leakage @ +25ºC @ +25ºC
tance tance
Size Part Number µA @ 25°C 120 Hz 100 kHz Size Part Number µA @ 25°C 120 Hz 100 kHz
µF µF
Max Max Max Max Max Max
**6 Volt Rating at +85ºC (4 Volt Rating at +125ºC)
2.5 Volt Rating at +85ºC (1.7 Volt Rating at +125ºC)
15.0 C T494C156(1)006A(2) 0.9 6.0 0.6
100.0 *T T494T107(1)2R5A(2) 2.5 24.0 3.5
15.0 B T494B156(1)006A(2) 0.9 6.0 0.7
3 Volt Rating at +85ºC (2 Volt Rating at +125ºC) #15.0 *A T494A156(1)006A(2) 0.9 6.0 2.0
#33.0 *A T494A336(1)003A(2) 1.0 6.0 2.0 #15.0 *T T494T156(1)006A(2) 0.9 6.0 2.5
4 Volt Rating at +85ºC (2.7 Volt Rating at +125ºC) #15.0 S T494S156M006A(2) 0.9 10.0 10.0
3.3 A T494A335(1)004A(2) 0.5 6.0 4.0 22.0 C T494C226(1)006A(2) 1.4 6.0 0.5
4.7 A T494A475(1)004A(2) 0.5 6.0 3.5 22.0 U T494U226(1)006A(2) 1.4 6.0 0.8
6.8 A T494A685(1)004A(2) 0.5 6.0 3.0 22.0 B T494B226(1)006A(2) 1.4 6.0 0.6
6.8 S T494S685(1)004A(2) 0.5 6.0 7.0 #22.0 *A T494A226(1)006A(2) 1.4 6.0 3.0
10.0 B T494B106(1)004A(2) 0.5 6.0 1.2 #22.0 *T T494T226M006A(2) 1.4 8.0 3.5
10.0 A T494A106(1)004A(2) 0.5 6.0 2.0 33.0 C T494C336(1)006A(2) 2.0 6.0 0.3
#10.0 *S T494S106(1)004A(2) 0.5 6.0 9.0 33.0 U T494U336(1)006A(2) 2.0 6.0 0.6
#10.0 *R T494R106M004A(2) 0.5 8.0 6.0 #33.0 *B T494B336(1)006A(2) 2.0 6.0 0.6
15.0 B T494B156(1)004A(2) 0.6 6.0 1.2 #33.0 *A T494A336(1)006A(2) 2.0 12.0 2.0
15.0 A T494A156(1)004A(2) 0.6 6.0 1.5 #33.0 T T494T336M006A(2) 2.0 12.0 4.0
15.0 T T494T156(1)004A(2) 0.6 6.0 2.0 47.0 D T494D476(1)006A(2) 2.9 6.0 0.22
#15.0 *S T494S156M004A(2) 0.6 10.0 9.0 47.0 C T494C476(1)006A(2) 2.9 6.0 0.25
22.0 C T494C226(1)004A(2) 0.9 6.0 0.5 #47.0 *U T494U476(1)006A(2) 2.9 6.0 0.60
22.0 B T494B226(1)004A(2) 0.9 6.0 0.6 #47.0 *B T494B476(1)006A(2) 2.9 6.0 0.50
#22.0 *A T494A226(1)004A(2) 0.9 6.0 1.5 †47.0 *A T494A476M006A(2) 3.0 12.0 2.50
#22.0 *S T494S226M004A(2) 0.9 10.0 8.0 47.0 *T T494T476(1)006A(2) 3.0 24.0 4.00
#22.0 *T T494T226(1)004A(2) 0.9 6.0 2.5 68.0 D T494D686(1)006A(2) 4.1 6.0 0.20
33.0 C T494C336(1)004A(2) 1.3 6.0 0.5 #68.0 *C T494C686(1)006A(2) 4.1 6.0 0.20
33.0 U T494U336(1)004A(2) 1.3 6.0 0.6 #68.0 *U T494U686(1)006A(2) 4.1 10.0 1.00
33.0 B T494B336(1)004A(2) 1.3 6.0 0.5 #68.0 *B T494B686M006A(2) 4.1 8.0 0.65
#33.0 *A T494A336(1)004A(2) 1.3 6.0 3.0 100.0 D T494D107(1)006A(2) 6.0 8.0 0.15
#33.0 *T T494T336M004A(2) 1.3 8.0 3.5 100.0 V T494V107(1)006A(2) 6.0 8.0 0.20
47.0 C T494C476(1)004A(2) 1.9 6.0 0.5 #100.0 *C T494C107(1)006A(2) 6.0 8.0 0.30
47.0 U T494U476(1)004A(2) 1.9 6.0 0.6 #100.0 U T494U107M006A(2) 6.0 10.0 1.20
#47.0 *B T494B476(1)004A(2) 1.9 6.0 0.5 #100.0 *B T494B107M006A(2) 6.0 15.0 1.50
#47.0 *A T494A476M004A(2) 1.9 12.0 2.0 150.0 D T494D157(1)006A(2) 9.0 8.0 0.15
#47.0 T T494T476M004A(2) 1.9 12.0 4.0 #150.0 *C T494C157M006A(2) 9.0 8.0 0.30
68.0 D T494D686(1)004A(2) 2.7 6.0 0.20 #150.0 *V T494V157(1)006A(2) 9.0 8.0 0.30
68.0 C T494C686(1)004A(2) 2.7 6.0 0.25 220.0 X T494X227(1)006A(2) 13.2 8.0 0.15
#68.0 *U T494U686(1)004A(2) 2.7 6.0 0.60 #220.0 *D T494D227(1)006A(2) 13.2 8.0 0.15
#68.0 *B T494B686(1)004A(2) 2.7 6.0 2.00 #220.0 *C T494C227M006A(2) 13.2 10.0 0.30
#68.0 A T494A686(1)004A(2) 2.8 30.0 3.00 #220.0 *V T494V227M006A(2) 13.2 12.0 0.30
100.0 D T494D107(1)004A(2) 4.0 8.0 0.20 #330.0 *X T494X337(1)006A(2) 19.8 8.0 0.15
#100.0 *C T494C107(1)004A(2) 4.0 8.0 0.20 #330.0 *D T494D337(1)006A(2) 19.8 8.0 0.15
#100.0 *U T494U107(1)004A(2) 4.0 10.0 1.00 #470.0 *X T494X477(1)006A(2) 28.2 10.0 0.10
#100.0 *B T494B107M004A(2) 4.0 8.0 0.65 #470.0 *D T494D477M006A(2) 28.2 12.0 0.15
†100.0 *A T494A107M004A(2) 4.0 30.0 3.00 #680.0 E T494E687M006A(2) 40.8 12.0 0.10
†100.0 *T T494T107M004A(2) 4.0 30.0 4.50 10 Volt Rating at +85ºC (7 Volt Rating at +125ºC)
150.0 D T494D157(1)004A(2) 6.0 8.0 0.15 1.5 A T494A155(1)010A(2) 0.5 6.0 6.0
150.0 V T494V157(1)004A(2) 6.0 8.0 0.20 2.2 B T494B225(1)010A(2) 0.5 6.0 1.5
#150.0 *C T494C157(1)004A(2) 6.0 8.0 0.30 2.2 A T494A225(1)010A(2) 0.5 6.0 6.0
†150.0 *B T494B157M004A(2) 6.0 12.0 1.00 3.3 A T494A335(1)010A(2) 0.5 6.0 4.0
#220.0 *V T494V227(1)004A(2) 8.8 8.0 0.30 3.3 S T494S335(1)010A(2) 0.5 6.0 9.0
#330.0 *D T494D337(1)004A(2) 13.2 8.0 0.15 #3.3 *R T494R335(1)010A(2) 0.3 8.0 10.0
#330.0 *C T494C337(1)004A(2) 13.2 10.0 0.09 4.7 B T494B475(1)010A(2) 0.5 6.0 1.5
†330.0 *V T494V337(1)004A(2) 13.2 12.0 0.30 4.7 A T494A475(1)010A(2) 0.5 6.0 3.0
#470.0 *X T494X477(1)004A(2) 18.8 8.0 0.15 #4.7 *S T494S475(1)010A(2) 0.5 6.0 9.0
#470.0 *D T494D477(1)004A(2) 18.8 8.0 0.15 #4.7 *R T494R475M010A(2) 0.5 8.0 8.0
#680.0 *X T494X687M004A(2) 27.2 12.0 0.10 6.8 B T494B685(1)010A(2) 0.7 6.0 1.2
#680.0 D T494D687M004A(2) 27.2 12.0 0.15 6.8 A T494A685(1)010A(2) 0.7 6.0 3.0
#1000.0 *X T494X108(1)004A(2) 40.0 12.0 0.10 6.8 T T494T685(1)010A(2) 0.7 6.0 2.0
#1000.0 *E T494E108M004A(2) 40.0 15.0 0.08 #6.8 *S T494S685M010A(2) 0.7 10.0 9.0
**6 Volt Rating at +85ºC (4 Volt Rating at +125ºC) 10.0 C T494C106(1)010A(2) 1.0 6.0 0.6
2.2 R T494R225(1)006A(2) 0.5 6.0 20.0 10.0 B T494B106(1)010A(2) 1.0 6.0 0.8
2.2 A T494A225(1)006A(2) 0.5 6.0 6.0 #10.0 *A T494A106(1)010A(2) 1.0 6.0 1.8
3.3 A T494A335(1)006A(2) 0.5 6.0 6.0 #10.0 *T T494T106(1)010A(2) 1.0 6.0 3.5
4.7 A T494A475(1)006A(2) 0.5 6.0 3.5 #10.0 S T494S106M010A(2) 1.0 10.0 12.0
4.7 S T494S475(1)006A(2) 0.5 6.0 8.0 15.0 C T494C156(1)010A(2) 1.5 6.0 0.5
6.8 B T494B685(1)006A(2) 0.5 6.0 1.2 15.0 U T494U156(1)010A(2) 1.5 6.0 0.8
6.8 A T494A685(1)006A(2) 0.5 6.0 2.0 15.0 B T494B156(1)010A(2) 1.5 6.0 0.7
#6.8 *S T494S685(1)006A(2) 0.5 6.0 9.0 #15.0 *A T494A156(1)010A(2) 1.5 8.0 4.0
#6.8 *R T494R685(1)006A(2) 0.5 8.0 10.0 #15.0 *T T494T156M010A(2) 1.5 8.0 3.5
10.0 B T494B106(1)006A(2) 0.6 6.0 1.0
10.0 A T494A106(1)006A(2) 0.6 6.0 2.0
10.0 T T494T106(1)006A(2) 0.6 6.0 1.2
#10.0 *S T494S106M006A(2) 0.6 10.0 9.0
#10.0 *R T494R106M006A(2) 0.6 8.0 6.0
*Extended Values
**6 Volt product equivalent to 6.3 volt product.
(1) To complete KEMET Part Number, insert M for ±20% tolerance or K for ±10% tolerance.
Higher voltage ratings, lower ESR, and tighter capacitance tolerance product may be
substituted within the same size at KEMET's option. Voltage substitutions will be marked
with the higher voltage rating.
#Maximum Capacitance Change @ 125ºC=+15%.
†Maximum Capacitance Chan ge @ 125ºC=+20%.

28 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 SOLID TANTALUM CHIP CAPACITORS
T494 SERIES—Low ESR, Industrial Grade

T494 RATINGS & PART NUMBER REFERENCE

DC DF % ESR Ω DC DF % ESR Ω
Capaci- Capaci-
Case KEMET Leakage @ +25ºC @ +25ºC Case KEMET Leakage @ +25ºC @ +25ºC
tance tance
Size Part Number µA @ 25°C 120 Hz 100 kHz Size Part Number µA @ 25°C 120 Hz 100 kHz
µF µF
Max Max Max Max Max Max
10 Volt Rating at +85ºC (7 Volt Rating at +125ºC) 16 Volt Rating at +85ºC (10 Volt Rating at + 125ºC)
22.0 C T494C226(1)010A(2) 2.2 6.0 0.4 100.0 X T494X107(1)016A(2) 16.0 8.0 0.15
22.0 U T494U226(1)010A(2) 2.2 6.0 0.8 #100.0 *D T494D107(1)016A(2) 16.0 8.0 0.15
#22.0 *B T494B226(1)010A(2) 2.2 6.0 0.7 †100.0 *V T494V107(1)016A(2) 16.0 12.0 0.5
#22.0 *A T494A226M010A(2) 2.2 10.0 4.5 #150.0 *X T494X157(1)016A(2) 24.0 8.0 0.15
#22.0 T T494T226M010A(2) 2.2 12.0 6.0 #150.0 *D T494D157(1)016A(2) 24.0 12.0 0.4

Solid Tantalum Surface Mount

33.0 D T494D336(1)010A(2) 3.3 6.0 0.25 #220.0 *X T494X227(1)016A(2) 35.2 10.0 0.4
33.0 V T494V336(1)010A(2) 3.3 6.0 0.30 20 Volt Rating at +85ºC (13 Volt Rating at +125ºC)
33.0 C T494C336(1)010A(2) 3.3 6.0 0.30 0.68 A T494A684(1)020A(2) 0.5 4.0 8.0
#33.0 *U T494U336(1)010A(2) 3.3 6.0 0.60 1.0 A T494A105(1)020A(2) 0.5 4.0 5.5
#33.0 *B T494B336(1)010A(2) 3.3 6.0 2.00 1.0 S T494S105(1)020A(2) 0.5 6.0 10.0
47.0 D T494D476(1)010A(2) 4.7 6.0 0.22 †1.0 R T494R105M020A(2) 0.2 6.0 15.0
47.0 V T494V476(1)010A(2) 4.7 6.0 0.30 1.5 A T494A155(1)020AS(2) 0.5 6.0 4.5
#47.0 *C T494C476(1)010A(2) 4.7 6.0 0.30 1.5 S T494S155(1)020A(2) 0.5 6.0 9.0
#47.0 *U T494U476(1)010A(2) 4.7 10.0 1.20 2.2 B T494B225(1)020A(2) 0.5 6.0 1.5
#47.0 *B T494B476M010A(2) 4.7 8.0 0.65 2.2 A T494A225(1)020A(2) 0.5 6.0 4.0
68.0 D T494D686(1)010A(2) 6.8 6.0 0.20 3.3 B T494B335(1)020A(2) 0.7 6.0 1.3
#68.0 *C T494C686(1)010A(2) 6.8 6.0 0.30 #3.3 *A T494A335(1)020A(2) 0.7 6.0 4.0
68.0 V T494V686(1)010A(2) 6.8 6.0 0.30 3.3 *T T494T335(1)020A(2) 0.7 6.0 4.0
#68.0 U T494U686M010A(2) 6.8 10.0 1.20 4.7 C T494C475(1)020A(2) 1.0 6.0 0.6
#68.0 *B T494B686M010A(2) 6.8 10.0 1.50 4.7 B T494B475(1)020A(2) 1.0 6.0 1.0
100.0 D T494D107(1)010A(2) 10.0 8.0 0.15 #4.7 *A T494A475(1)020A(2) 1.0 8.0 3.0
#100.0 *C T494C107(1)010A(2) 10.0 8.0 0.20 6.8 C T494C685(1)020A(2) 1.4 6.0 0.6
#100.0 *V T494V107(1)010A(2) 10.0 8.0 0.40 6.8 U T494U685(1)020A(2) 1.4 6.0 1.4
150.0 X T494X157(1)010A(2) 15.0 8.0 0.15 #6.8 *B T494B685(1)020A(2) 1.4 6.0 1.0
#150.0 *D T494D157(1)010A(2) 15.0 8.0 0.15 10.0 C T494C106(1)020A(2) 2.0 6.0 0.5
#150.0 *C T494C157(1)010A(2) 15.0 10.0 0.90 10.0 U T494U106(1)020A(2) 2.0 6.0 0.8
#150.0 V T494V157M010A(2) 15.0 8.0 0.30 #10.0 *B T494B106(1)020A(2) 2.0 6.0 1.0
#220.0 *X T494X227(1)010A(2) 22.0 8.0 0.15 15.0 D T494D156(1)020A(2) 3.0 6.0 0.35
#220.0 *D T494D227(1)010A(2) 22.0 8.0 0.15 15.0 *C T494C156(1)020A(2) 3.0 6.0 0.40
#220.0 *V T494V227(1)010A(2) 22.0 12.0 0.50 22.0 D T494D226(1)020A(2) 4.4 6.0 0.3
#330.0 X T494X337(1)010A(2) 33.0 10.0 0.10 22.0 V T494V226(1)020A(2) 4.4 6.0 0.4
#330.0 *D T494D337M010A(2) 33.0 10.0 0.15 #22.0 *C T494C226(1)020A(2) 4.4 6.0 0.4
#470.0 *X T494X477(1)010A(2) 47.0 10.0 0.10 33.0 D T494D336(1)020A(2) 6.6 6.0 0.25
#470.0 E T494E477M010A(2) 47.0 12.0 0.10 #33.0 *C T494C336M020A(2) 6.6 6.0 0.40
16 Volt Rating at +85ºC (10 Volt Rating at + 125ºC) †33.0 V T494V336(1)020A(2) 6.6 8.0 0.40
1.0 A T494A105(1)016A(2) 0.5 4.0 6.0 47.0 *D T494D476(1)020A(2) 9.4 6.0 0.2
1.5 A T494A155(1)016A(2) 0.5 6.0 6.0 68.0 X T494X686(1)020A(2) 13.6 6.0 0.2
2.2 A T494A225(1)016A(2) 0.5 6.0 4.0 #68.0 *D T494D686(1)020A(2) 13.6 8.0 0.2
2.2 *S T494S225(1)016A(2) 0.5 6.0 10.0 #100.0 *X T494X107(1)020A(2) 20.0 8.0 0.15
#2.2 *R T494R225(1)016A(2) 0.5 8.0 20.0 25 Volt Rating at +85ºC (17 Volt Rating at +125ºC)
3.3 B T494B335(1)016A(2) 0.5 6.0 2.0 0.33 A T494A334(1)025A(2) 0.5 4.0 10.0
3.3 A T494A335(1)016A(2) 0.5 6.0 4.0 0.47 A T494A474(1)025A(2) 0.5 4.0 9.0
4.7 B T494B475(1)016A(2) 0.8 6.0 1.5 0.68 A T494A684(1)025A(2) 0.5 4.0 6.0
4.7 A T494A475(1)016A(2) 0.8 6.0 3.0 1.0 B T494B105(1)025A(2) 0.5 4.0 2.0
4.7 T T494T475(1)016A(2) 0.8 6.0 3.0 1.0 *A T494A105(1)025A(2) 0.5 4.0 4.0
6.8 C T494C685(1)016A(2) 1.1 6.0 0.8 1.5 B T494B155(1)025A(2) 0.5 6.0 1.5
6.8 B T494B685(1)016A(2) 1.1 6.0 1.2 1.5 *A T494A155(1)025A(2) 0.5 6.0 3.0
#6.8 *A T494A685(1)016A(2) 1.1 6.0 3.0 2.2 C T494C225(1)025A(2) 0.6 6.0 2.2
10.0 C T494C106(1)016A(2) 1.6 6.0 0.6 2.2 B T494B225(1)025A(2) 0.6 6.0 1.2
10.0 U T494U106(1)016A(2) 1.6 6.0 1.0 3.3 C T494C335(1)025A(2) 0.9 6.0 1.2
10.0 B T494B106(1)016A(2) 1.6 6.0 0.8 3.3 *B T494B335(1)025A(2) 0.9 6.0 2.0
#10.0 *A T494A106(1)016A(2) 1.6 10.0 3.0 4.7 C T494C475(1)025A(2) 1.2 6.0 0.6
#10.0 *T T494T106M016A(2) 1.6 8.0 6.0 #4.7 *B T494B475(1)025A(2) 1.2 6.0 1.0
15.0 C T494C156(1)016A(2) 2.4 6.0 0.4 6.8 C T494C685(1)025A(2) 1.7 6.0 0.6
15.0 U T494U156(1)016A(2) 2.4 6.0 0.8 6.8 *B T494B685(1)025A(2) 1.7 8.0 2.0
#15.0 *B T494B156(1)016A(2) 2.4 6.0 0.8 10.0 D T494D106(1)025A(2) 2.5 6.0 0.4
22.0 D T494D226(1)016A(2) 3.6 6.0 0.25 10.0 *C T494C106(1)025A(2) 2.5 6.0 0.6
22.0 C T494C226(1)016A(2) 3.6 6.0 0.35 15.0 D T494D156(1)025A(2) 3.8 6.0 0.35
#22.0 *U T494U226(1)016A(2) 3.6 10.0 1.80 #15.0 *C T494C156(1)025A(2) 3.8 6.0 0.90
#22.0 *B T494B226(1)016A(2) 3.6 6.0 1.00 22.0 D T494D226(1)025A(2) 5.5 6.0 0.3
33.0 D T494D336(1)016A(2) 5.3 6.0 0.25 22.0 *C T494C226(1)025A(2) 5.5 8.0 1.0
#33.0 *C T494C336(1)016A(2) 5.3 6.0 0.30 22.0 *V T494V226(1)025A(2) 5.5 6.0 0.5
#33.0 *U T494U336(1)016A(2) 5.3 12.0 2.20 33.0 X T494X336(1)025A(2) 8.3 6.0 0.3
47.0 D T494D476(1)016A(2) 7.5 6.0 0.2 #33.0 *D T494D336(1)025A(2) 8.3 6.0 0.4
47.0 V T494V476(1)016A(2) 7.5 6.0 0.3 #47.0 *X T494X476(1)025A(2) 11.8 6.0 0.3
#47.0 *C T494C476(1)016A(2) 7.5 6.0 0.5 †47.0 *D T494D476(1)025A(2) 11.8 10.0 0.2
68.0 *D T494D686(1)016A(2) 10.9 6.0 0.15 †68.0 *X T494X686M025A(2) 17.0 8.0 0.3
#68.0 *V T494V686(1)016A(2) 10.9 6.0 0.5
Note: Refer to T494 Ordering Information on page 27 for lead termination options.
*Extended Values
**6 Volt product equivalent to 6.3 volt product.
(1) To complete KEMET Part Number, insert M for ±20% tolerance or K for ±10% tolerance.
Higher voltage ratings, lower ESR, and tighter capacitance tolerance product may be
substituted within the same size at KEMET's option. Voltage substitutions will be marked
with the higher voltage rating.
#Maximum Capacitance Change @ 125ºC=+15%.
†Maximum Capacitance Change @ 125ºC=+20%.

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 29
 SOLID TANTALUM CHIP CAPACITORS
T494 SERIES—Low ESR, Industrial Grade

T494 RATINGS & PART NUMBER REFERENCE

DC DF ESR DC DF ESR
Capaci- Capaci-
Case KEMET Leakage % @ +25°C Ω @ +25°C Case KEMET Leakage % @ +25°C Ω @ +25°C
tance tance
Size Part Number µA @ 25°C 120 Hz 100 kHz Size Part Number µA @ 25°C 120 Hz 100 kHz
µF µF
Max Max Max Max Max Max
25 Volt Rating at +85ºC (17 Volt Rating at +125ºC) 50 Volt Rating at +85ºC (33 Volt Rating at +125ºC)
0.33 A T494A334(1)025AS 0.5 4.0 10.0 0.1 A T494A104(1)050AS 0.5 4.0 10.0
0.47 A T494A474(1)025AS 0.5 4.0 9.0 0.15 B T494B154(1)050AS 0.5 4.0 10.0
0.68 A T494A684(1)025AS 0.5 4.0 6.0 0.15 *A T494A154(1)050AS 0.5 4.0 10.0
1.0 B T494B105(1)025AS 0.5 4.0 2.0 0.22 B T494B224(1)050AS 0.5 4.0 10.0
1.0 *A T494A105(1)025AS 0.5 4.0 4.0 0.33 B T494B334(1)050AS 0.5 4.0 2.5
1.5 B T494B155(1)025AS 0.5 6.0 1.5 0.47 C T494C474(1)050AS 0.5 4.0 1.8
1.5 *A T494A155(1)025AS 0.5 6.0 5.0 0.47 *B T494B474(1)050AS 0.5 4.0 2.0
2.2 C T494C225(1)025AS 0.6 6.0 2.2 0.68 C T494C684(1)050AS 0.5 4.0 1.6
2.2 B T494B225(1)025AS 0.6 6.0 1.2 0.68 *B T494B684(1)050AS 0.5 4.0 3.0
3.3 C T494C335(1)025AS 0.9 6.0 1.2 1.0 C T494C105(1)050AS 0.5 4.0 1.6
3.3 *B T494B335(1)025AS 0.9 6.0 2.0 #1.0 *V T494V105M050AS 0.5 4.0 4.0
4.7 C T494C475(1)025AS 1.2 6.0 0.6 1.5 D T494D155(1)050AS 0.8 6.0 1.0
#4.7 *B T494B475(1)025AS 1.2 6.0 1.0 1.5 *C T494C155(1)050AS 0.8 6.0 1.5
6.8 C T494C685(1)025AS 1.7 6.0 0.6 2.2 D T494D225(1)050AS 1.1 6.0 0.8
10.0 D T494D106(1)025AS 2.5 6.0 0.4 2.2 *C T494C225(1)050AS 1.1 6.0 1.5
10.0 *C T494C106(1)025AS 2.5 6.0 0.6 3.3 D T494D335(1)050AS 1.7 6.0 0.8
15.0 D T494D156(1)025AS 3.8 6.0 0.35 4.7 D T494D475(1)050AS 2.4 6.0 0.6
#15.0 *C T494C156(1)025AS 3.8 6.0 0.90 6.8 X T494X685(1)050AS 3.5 6.0 0.5
22.0 D T494D226(1)025AS 5.5 6.0 0.3 #6.8 D T494D685(1)050AS 3.4 6.0 0.7
22.0 *V T494V226(1)025AS 5.5 6.0 0.5 #10.0 X T494X106M050AS 5.0 6.0 0.4
33.0 X T494X336(1)025AS 8.3 6.0 0.3 †15.0 *X T494X156(1)050AS 7.5 6.0 0.4
#33.0 *D T494D336(1)025AS 8.3 6.0 0.4 *Extended Values
#47.0 *X T494X476(1)025AS 11.8 6.0 0.3 **6 Volt product equivalent to 6.3 volt product.
†47.0 D T494D476(1)025AS 11.8 10.0 0.2 (1) To complete KEMET Part Number, insert M for ±20% tolerance or K for ±10% tolerance.
†68.0 X T494X686M025AS 17.0 8.0 0.3 Higher voltage ratings, lower ESR, and tighter capacitance tolerance product may be
35 Volt Rating at +85ºC (23 Volt Rating at +125ºC) substituted within the same size at KEMET's option. Voltage substitutions will be marked
0.1 A T494A104(1)035AS 0.5 4.0 10.0 with the higher voltage rating.
0.15 A T494A154(1)035AS 0.5 4.0 6.0 #Maximum Capacitance Change @ 125ºC=+15%.
0.22 A T494A224(1)035AS 0.5 4.0 6.0 †Maximum Capacitance Change @ 125ºC=+20%.
0.33 A T494A334(1)035AS 0.5 4.0 6.0
0.47 B T494B474(1)035AS 0.5 4.0 2.5 Note: Refer to T494 Ordering Information on page 27 for lead termination options.
0.47 A T494A474(1)035AS 0.5 4.0 4.0
0.68 B T494B684(1)035AS 0.5 4.0 2.5
0.68 *A T494A684(1)035AS 0.5 4.0 6.0
1.0 B T494B105(1)035AS 0.5 4.0 2.0
1.0 *A T494A105(1)035AS 0.5 4.0 6.0
1.5 C T494C155(1)035AS 0.5 6.0 2.5
1.5 B T494B155(1)035AS 0.5 6.0 3.0
2.2 C T494C225(1)035AS 0.8 6.0 1.5
2.2 *B T494B225(1)035AS 0.8 6.0 2.5
3.3 C T494C335(1)035AS 1.2 6.0 0.8
#3.3 B T494B335(1)035AS 1.2 6.0 1.3
4.7 D T494D475(1)035AS 1.7 6.0 0.7
4.7 C T494C475(1)035AS 1.7 6.0 0.7
6.8 D T494D685(1)035AS 2.4 6.0 0.5
6.8 *C T494C685(1)035AS 2.4 6.0 0.9
10.0 D T494D106(1)035AS 3.5 6.0 0.4
#10.0 *C T494C106M035AS 3.5 6.0 1.2
#10.0 *V T494V106(1)035AS 3.5 6.0 0.8
15.0 X T494X156(1)035AS 5.3 6.0 0.30
15.0 *D T494D156(1)035AS 5.3 6.0 0.35
#22.0 X T494X226(1)035AS 7.7 6.0 0.3
#22.0 *D T494D226(1)035AS 7.7 6.0 0.4
#33.0 *X T494X336(1)035AS 11.6 6.0 0.3
†47.0 *X T494X476(1)035AS 16.5 8.0 0.5
#47.0 E T494E476(1)035AS 16.5 10.0 0.3

CAPACITOR MARKINGS CONSTRUCTION

T494 Series — All Case Sizes Negative
Termination*
Silver Adhesive
Washer
Polarity
Stripe (+)
Molded Polarity
Case Bevel (+)
Polarity
Indicator (+) Tantalum
(• Denotes T494) Wire

107 Picofarad
Code

Rated
Voltage
10K KEMET
I. D. Symbol
Tantalum
Weld
427 (Ta2O5)

Mn02 Coat
(First Layer)
Carbon
Print Week Code: (Second Layer)
Positive
1st Digit = Y ear Silver Paint Termination*
2nd & 3rd Digits = Week (Third Layer)
"427" = The 27th week of 2004 *100% tin

30 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 SOLID TANTALUM CHIP CAPACITORS
T495 SERIES—Low ESR, Surge Robust

FEATURES
• Designed for very low ESR • New Extended Values for Low ESR
• High ripple current capability • Low Equivalent Series Inductance (2.5nH ESL)
• High surge current capability • Precision-molded, laser-marked case
• 100% accelerated steady-state aging • Symmetrical, compliant terminations
• 100% Surge Current test • Taped and reeled per EIA 481-1
• Meets or Exceeds EIA Standard 535BAAC • RoHS Compliant & Leadfree Terminations (see
• Available tested per DSCC Dwg. 95158 www.kemet.com for lead transition)

Solid Tantalum Surface Mount

OUTLINE DRAWING
CATHODE (-) END SIDE VIEW ANODE (+) END BOTTOM VIEW
VIEW VIEW
B
W
B

H E F
K T P

S S R Termination A
X G cutout at L
KEMET’s
Option,
either end

STANDARD T495 DIMENSIONS

Millimeters (Inches)
CASE SIZE COMPONENT
± 0.20 ± 0.1 ± 0.3 B ± 0.15 X P R T A G E
KEMA EIA L W H K ± (.008) F S ± (.012) (Ref) ± (.006)
± (.004) (Ref) (Ref) (Ref) (Ref) (Min) (Ref) (Ref)
B 3528-21 3.5 ± 0.2 2.8 ± 0.2 1.9 ± 0.2 1.1 2.2 0.8 0.4 0.10 ± 0.10 0.5 1.0 0.13 1.1 1.8 2.2
(.138 ± .008) (.110 ± .008) (.075 ± .008) (.043) (.087) (.031) (.016) (.004 ± .004) (.020) (.039) (.005) (.043) (.071) (.087)
C 6032-28 6.0 ± 0.3 3.2 ± 0.3 2.5 ± 0.3 1.4 2.2 1.3 0.5 0.10 ± 0.10 0.9 1.0 0.13 2.5 2.8 2.4
(.236 ± .012) (.126 ± .012) (.098 ± .012) (.055) (.087) (.051) (.020) (.004 ± .004) (.035) (.039) (.005) (.098) (.110) (.094)
D 7343-31 7.3 ± 0.3 4.3 ± 0.3 2.8 ± 0.3 1.5 2.4 1.3 0.5 0.10 ± 0.10 0.9 1.0 0.13 3.8 3.5 3.5
(.287 ± .012) (.169 ± .012) (.110 ± .012) (.059) (.094) (.051) (.020) (.004 ± .004) (.035) (.039) (.005) (.150) (.138) (.138)
X 7343-43 7.3 ± 0.3 4.3 ± 0.3 4.0 ± 0.3 2.3 2.4 1.3 0.5 0.10 ± 0.10 1.7 1.0 0.13 3.8 3.5* 3.5*
(.287 ± .012) (.169 ± .012) (.157 ± .012) (.091) (.094) (.051) (.020) (.004 ± .004) (.067) (.039) (.005) (.150) (.138) (.138)

Notes: 1. Metric dimensions govern.

2. (Ref) - Dimensions provided for reference only.
* Round Glue Pad; 2.9 ±0.1mm (0.114" ± 0.004") in diameter at KEMET's option.

LOW PROFILE T495 DIMENSIONS

Millimeters (Inches)
CASE SIZE COMPONENT
X T A G E
KEMET EIA L W H Max. K Min. F ± 0.1 S ± 0.3
(Ref (Ref) (Min) (Ref) (Ref)
T 3528-12 3.5 ± 0.2 2.8 ± 0.2 1.2 0.3 2.2 0.8 0.05 0.13 1.1 1.8 2.2
(.138 ± .008) (.110 ± .008) (.047) (.012) (.087) (.031) (.002) (.005) (.043) (.071) (.087)
V 7343-20 7.3 ± 0.3 4.3 ± 0.3 2.0 0.9 2.4 1.3 0.05 0.13 3.8 3.5 3.5
(.287 ± .012) (.169 ± .012) (0.079) (.035) (.094) (.051) (.002) (.005) (.150) (.138) (.138)
Notes: 1. Metric dimensions govern.
2. (Ref) - Dimensions provided for reference only.
3. No dimensions provided for B, P or R because low profile cases do not have a bevel or a notch.

ORDERING INFORMATION
T 495 X 107 M 010 A S E100
Tantalum ESR
E100 = ESR in Milliohmns = 100 mOhms
Series E1K5 = ESR in Ohms = 1.5 Ohms
T495 - Low ESR, Surge Robust 4095 = DSCC Dwg. 95158 Designator

Case Size Lead Material

S = 100% Tin (Sn) Plated
B, C, D, T, V, X
H = (Sn) Solder-Coated (90% Sn/10% Pb)
Capacitance Picofarad Code G = Gold Plated
First two digits represent significant figures. Third digit T = 100% Tin (Sn) Plated
specifies number of zeros to follow. Failure Rate
A = Not Applicable
Capacitance Tolerance
M = ±20%, K = ±10% See www.kemet.com for Pb Free transition information. Voltage

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 31
 SOLID TANTALUM CHIP CAPACITORS
T495 SERIES—Low ESR, Surge Robust

T495 RATINGS & PART NUMBER REFERENCE

DC DF% ESR mΩ
DSCC Dwg. Ripple Current mA rms @
Capaci- Case KEMET Leakage @ 25°C @ 25°C
No. 95158 25°C, 100 kHz Max
tance µF Size Part Number µA @ 25°C 120 Hz 100 kHz
Part Number
Max Max Max 25°C 85°C 125°C
2.5 Volt Rating @ +85°C (1.7 Volt Rating at +125°C)
100.0 T T495T107M2R5A(2) E3K0 2.5 24.0 3000 153 137 61
4 Volt Rating @ +85°C (2.7 Volt Rating at +125°C)
150.0 B T495B157M004A(2) E900 6.0 12.0 900 307 277 123
330.0 C T495C337(1)004A(2) E700 13.2 12.0 700 396 357 159
1000.0 X T495X108(1)004A(2) E070 40.0 12.0 70 1535 1381 614
6/6.3 Volt Rating @ +85°C (4 Volt Rating at +125°C)
68.0 D T495D686(1)006A(2)E175 3.3 4.0 175 926 833 370
68.0 D T495D686(1)006A(2)4095 95158-01(1)(2) 3.3 4.0 175 926 833 370
100.0 C T495C107(1)006A(2)E150 6.0 8.0 150 856 770 342
100.0 V T495V107(1)006A(2)E150 6.0 8.0 150 913 822 365
100.0 *B T495B107M006A(2)E700 6.3 15.0 700 348 313 139
150.0 *C T495C157M006A(2)E200 9.0 8.0 200 742 668 297
150.0 X T495X157(1)006A(2)E100 7.2 6.0 100 1285 1156 514
150.0 X T495X157(1)006A(2)4095 95158-02(1)(2) 7.2 6.0 125 1150 1040 460
220.0 *C T495C227(1)006A(2)E225 13.9 10.0 225 700 600 300
220.0 D T495D227(1)006A(2)E100 13.2 8.0 100 1225 1102 490
220.0 D T495D227(1)006A(2)4095 95158-25(1)(2) 13.2 8.0 100 1225 1102 490
220.0 X T495X227(1)006A(2)E100 13.2 8.0 100 1285 1156 514
220.0 X T495X227(1)006A(2)4095 95158-03(1)(2) 13.2 8.0 100 1285 1156 514
330.0 *D T495D337(1)006A(2)E100 20.8 8.0 100 1225 1102 490
330.0 *X T495X337(1)006A(20E100 19.8 8.0 100 1285 1156 514
330.0 *X T495X337(1)006A(2)E065 19.8 8.0 65 1593 1434 637
470.0 *D T495D477(1)006A(2)E125 29.6 12.0 125 1095 986 438
470.0 *X T495X477(1)006A(2)E065 28.2 10.0 65 1593 1434 637
470.0 *X T495X477(1)006A(2)E050 28.2 10.0 50 1816 1634 726
10 Volt Rating @ +85°C (7 Volt Rating at +125°C)
22.0 C T495C226(1)010A(2)E290 2.2 6.0 290 616 554 246
22.0 C T495C226(1)010A(2)E345 2.2 6.0 345 565 508 226
47.0 D T495D476(1)010A(2)E080 3.8 4.0 80 1369 1232 548
47.0 D T495D476(1)010A(2)E090 4.7 6.0 90 1291 1162 516
47.0 D T495D476(1)010A(2)E200 3.8 4.0 200 866 780 346
47.0 D T495D476(1)010A(2)4095 95158-04(1)(2) 3.8 4.0 200 866 780 346
68.0 B T495B686(1)010A(2)E750 1.5 10.0 750 337 303 135
68.0 *B T495B686M010A(2)E900 6.8 10.0 900 307 276 123
68.0 C T495C686(1)010A(2)E225 6.8 6.0 225 700 630 280
68.0 V T495V686(1)010A(2)E140 6.8 6.0 140 945 850 378
68.0 D T495D686(1)010A(2)E090 6.8 6.0 90 1291 1162 516
68.0 D T495D686(1)010A(2)E150 6.8 6.0 150 1000 900 400
68.0 X T495X686(1)010A(2)E150 5.4 4.0 150 1049 944 420
68.0 X T495X686(1)010A(2)4095 95158-05(1)(2) 5.4 4.0 150 1049 944 420
100.0 V T495V107(1)010A(2)E150 10.0 8.0 150 913 822 365
100.0 D T495D107(1)010A(2)E100 10.0 8.0 100 1220 1100 490
100.0 D T495D107(1)010A(2)4095 95158-06(1)(2) 10.0 8.0 100 1220 1100 490
100.0 *D T495D107(1)010A(20E080 10.0 8.0 80 1369 1232 548
100.0 X T495X107(1)010A(2)E100 8.0 6.0 100 1285 1156 514
100.0 X T495X107(1)010A(2)4095 95158-07(1)(2) 8.0 6.0 100 1285 1156 514
150.0 *V T495V157M010A(2)E150 15.0 8.0 150 913 822 365
150.0 D T495D157(1)010A(2)E100 15.0 8.0 100 1225 1102 490
150.0 D T495D157(1)010A(2)E080 15.0 8.0 80 1369 1232 548
150.0 D T495D157(1)010A(2)4095 95158-26(1)(2) 15.0 8.0 100 1225 1102 490
150.0 X T495X157(1)010A(2)E100 15.0 8.0 100 1285 1156 514
150.0 X T495X157(1)010A(2)4095 95158-08(1)(2) 15.0 8.0 100 1285 1156 514
150.0 X T495X157(1)010A(2)E085 15.0 8.0 85 1393 1254 557
220.0 *V T495V227(1)010A(2)E150 22.0 12.0 150 913 822 365
220.0 D T495D227(1)010A(2)E075 22.0 8.0 75 1414 1273 566
220.0 D T495D227(1)010A(2)E100 22.0 8.0 100 1225 1102 490
220.0 D T495D227(1)010A(2)E125 22.0 8.0 125 1095 986 438
220.0 X T495X227(1)010A(2)E100 22.0 8.0 100 1285 1156 514
220.0 X T495X227(1)010A(2)4095 95158-28(1)(2) 15.0 8.0 100 1285 1156 514
220.0 X T495X227(1)010A(2)E070 22.0 8.0 70 1535 1382 614
330.0 *D T495D337(1)010A(2)E125 33.0 10.0 125 1095 986 438
330.0 *X T495X337(1)010A(2)E050 33.0 10.0 50 1817 1635 727
330.0 *X T495X337(1)010A(2)E060 33.0 10.0 60 1658 1492 663
16 Volt Rating @ +85°C (10 Volt Rating at +125°C)
10.0 *T T495T106M016A(2)E4K0 1.6 8.0 4000 132 119 53
33.0 C T495C336(1)016A(2)E225 5.3 6.0 225 699 629 280
33.0 *C T495C336(1)016A(2)E275 5.3 6.0 275 632 569 253
33.0 D T495D336(1)020A(2)E150 6.6 6.0 150 1000 900 400
33.0 D T495D336(1)016A(2)E175 5.3 6.0 175 926 833 370
33.0 D T495D336(1)016A(2)E225 4.2 4.0 225 816 735 327
33.0 D T495D336(1)016A(2)4095 95158-09(1)(2) 4.2 4.0 250 770 700 310
47.0 D T495D476(1)016A(2)E100 7.5 6.0 100 1225 1102 490
47.0 D T495D476(1)016A(2)E150 7.5 6.0 150 1000 900 400
47.0 D T495D476(1)016A(2)4095 95158-10(1)(2) 7.5 6.0 200 870 780 345
68.0 *V T495V686(1)016A(2)E300 10.9 6.0 300 645 581 258
68.0 D T495D686(1)016A(2)E150 10.9 6.0 150 1000 900 400
100.0 *D T495D107(1)016(2)E100 16.0 8.0 100 1225 1102 490
100.0 *D T495D107(1)016A(2)E125 16.0 8.0 125 1095 986 438
100.0 X T495X107(1)016A(2)E100 16.0 8.0 100 1285 1156 514
100.0 X T495X107(1)016A(2)4095 95158-11(1)(2) 16.0 8.0 125 1149 1034 460
100.0 X T495X107(1)016A(2)E080 16.0 8.0 80 1436 1293 574
150.0 *X T495X157(1)016A(2)E100 24.0 8.0 100 1285 1156 514

(1) To complete KEMET Part Number, insert M for ±20% or K for ±10% tolerance. Higher voltage ratings, lower ESR and tighter capacitance tolerance product may be
(2) To complete KEMET Part Number, insert termination finish as designated on page 31. substituted within the same size at KEMET’s option. Voltage substitutions will be marked
*Extended Values**6 Volt product equivalent to 6.3 volt product. with the higher voltage rating.
Note: Refer to T495 Ordering Information on page 31 for lead termination options.

32 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 SOLID TANTALUM CHIP CAPACITORS
T495 SERIES—Low ESR, Surge Robust

T495 RATINGS & PART NUMBER REFERENCE

DC DF% ESR mΩ Ripple Current mA rms @
DSCC Dwg.
Capaci- Case KEMET Leakage @ 25°C @ 25°C 25°C, 100 kHz Max
No. 95158
tance µF Size Part Number µA @ 25°C 120 Hz 100 kHz
Part Number
Max Max Max 25°C 85°C 125°C
20 Volt Rating @ +85°C (13 Volt Rating at +125°C)
15.0 D T495D156(1)020A(2)E275 2.4 4.0 275 738 665 295
15.0 D T495D156(1)020A(2)4095 95158-12(1)(2) 2.4 4.0 275 738 665 295
22.0 D T495D226(1)020A(2)E225 3.5 4.0 225 816 735 326
22.0 D T495D226(1)020A(2)4095 95158-13(1)(2) 3.5 4.0 275 739 665 295
33.0 D T495D336(1)020A(2)E150 6.6 6.0 150 1000 900 400
33.0 D T495D336(1)020A(2)E200 6.6 6.0 200 866 780 346
47.0 D T495D476(1)020A(2)E175 9.4 6.0 175 926 833 370

Solid Tantalum Surface Mount

47.0 X T495X476(1)020A(2)E100 9.4 6.0 100 1285 1156 514
47.0 X T495X476(1)020A(2)E125 9.4 6.0 125 1149 1034 460
47.0 X T495X476(1)020A(2)E150 7.5 4.0 150 1049 944 420
47.0 X T495X476(1)020A(2)4095 95158-14(1)(2) 7.5 4.0 150 1049 944 420
68.0 *D T495D686(1)020A(2)E150 13.6 8.0 150 1000 900 400
68.0 X T495X686(1)020A(2)E120 13.6 6.0 120 1173 1055 469
68.0 X T495X686(1)020A(2)E150 13.6 6.0 150 1049 944 420
68.0 X T495X686(1)020A(2)4095 95158-15(1)(2) 13.6 6.0 150 1049 944 420
25 Volt Rating @ +85°C (17 Volt Rating at +125°C)
6.8 *B T495B685(1)025A(2)E1K5 1.7 6.0 1500 238 214 95
6.8 C T495C685(1)025A(2)E490 1.7 6.0 490 474 426 190
6.8 C T495C685(1)025A(2)E500 1.7 6.0 500 469 422 188
10.0 *C T495C106(1)025A(2)E450 2.5 6.0 450 494 445 198
15.0 D T495D156(1)025A(2)E275 3.8 6.0 275 738 665 295
15.0 D T495D156(1)025A(2)4095 95158-16(1)(2) 3.8 6.0 275 738 665 295
15.0 X T495X156(1)025A(2)E200 3.0 4.0 200 908 817 363
15.0 X T495X156(1)025A(2)4095 95158-17(1)(2) 3.0 4.0 200 908 817 363
22.0 *C T495C226(1)025A(2)E900 5.5 6.0 900 350 315 140
22.0 *D T495D226(1)025A(2)E200 5.5 6.0 200 866 780 346
22.0 X T495X226(1)025A(2)E225 4.4 4.0 225 856 771 343
22.0 X T495X226(1)025A(2)4095 95158-18(1)(2) 4.4 4.0 225 856 771 343
33.0 D T495D336(1)025A(2)E225 8.3 6.0 225 816 735 327
33.0 *D T495D336(1)025A(2)E300 8.3 6.0 300 707 636 283
33.0 X T495X336(1)025A(2)E175 6.6 4.0 175 971 874 388
33.0 X T495X336(1)025A(2)4095 95158-19(1)(2) 6.6 4.0 175 971 874 388
47.0 *X T495X476M025A(2)E185 16.5 8.0 185 944 850 378
47.0 *X T495X476M025A(2)E200 11.8 6.0 200 908 817 363
68.0 *X T495X686(1)025A(2)E200 17.0 8.0 200 908 817 363
35 Volt Rating @ +85°C (23 Volt Rating at +125°C)
4.7 C T495C475(1)035A(2)E500 1.7 6.0 500 469 422 188
4.7 *C T495C475(1)035A(2)E600 1.7 6.0 600 428 385 171
4.7 *C T495C475(1)035A(2)4095 95158-29(1)(2) 1.7 6.0 600 428 385 171
6.8 D T495D685(1)035A(2)E400 2.4 6.0 400 612 551 245
6.8 X T495X685(1)035A(2)E300 1.9 4.0 300 742 667 297
6.8 X T495X685(1)035A(2)4095 95158-20(1)(2) 1.9 4.0 300 742 667 297
10.0 D T495D106(1)035A(2)E300 3.5 6.0 300 707 636 283
10.0 D T495D106(1)035A(2)4095 95158-27(1)(2) 3.5 4.0 300 707 636 283
10.0 X T495X106(1)035A(2)E175 3.5 6.0 175 971 874 388
10.0 X T495X106(1)035A(2)E200 3.5 6.0 200 908 817 363
10.0 X T495X106(1)035A(2)E250 2.8 4.0 250 812 731 325
10.0 X T495X106(1)035A(2)4095 95158-21(1)(2) 2.8 4.0 250 812 731 325
15.0 D T495D156(1)035A(2)E225 5.3 6.0 225 816 735 327
15.0 *D T495D156(1)035A(2)E300 5.3 6.0 300 707 636 283
15.0 *X T495X156(1)035A(2)E225 5.3 6.0 225 856 771 343
15.0 *X T495X156(1)035A(2)4095 95158-22(1)(2) 5.3 6.0 225 856 771 343
22.0 D T495D226(1)035A(2)E200 7.7 6.0 200 866 779 346
22.0 D T495D226(1)035A(2)E250 7.7 6.0 250 775 697 310
22.0 *D T495D226(1)035A(2)E300 7.7 6.0 300 707 636 283
22.0 *X T495X226(1)035A(2)E275 7.7 6.0 275 775 697 410
22.0 *X T495X226(1)035A(2)4095 95158-23(1)(2) 7.7 6.0 300 742 667 297
33.0 X T495X336(1)035A(2)E175 11.6 6.0 175 971 874 388
33.0 *X T495X336(1)035A(2)E250 11.6 6.0 250 812 731 325
47.0 X T495X476(1)035A(2)E185 16.5 8.0 185 944 850 378
47.0 X T495X476(1)035A(2)E200 16.5 8.0 200 908 817 363
47.0 *X T495X476(1)035A(2)E300 16.5 8.0 300 742 667 297
50 Volt Rating @ +85°C (33 Volt Rating at +125°C)
4.7 D T495D475(1)050A(2)E300 2.4 6.0 300 707 636 283
4.7 X T495X475(1)050A(2)E300 1.9 4.0 300 742 667 297
4.7 X T495X475(1)050A(2)4095 95158-24(1)(2) 1.9 4.0 300 742 667 297
6.8 D T495D685(1)050A(2)E275 3.4 6.0 275 739 665 295
6.8 *D T495D685(1)050A(2)E300 3.4 8.0 300 700 600 300
10.0 *X T495X106(1)050A(2)E300 5.0 6.0 300 741 667 297
15.0 *X T495X156(1)050A(2)E300 7.5 8.0 300 742 667 297

(1) To complete KEMET Part Number, insert M for ±20% or K for ±10% tolerance. Higher voltage ratings, lower ESR and tighter capacitance tolerance product may be
(2) To complete KEMET Part Number, insert termination finish as designated on page 31. substituted within the same size at KEMET’s option. Voltage substitutions will be marked
*Extended Values**6 Volt product equivalent to 6.3 volt product. with the higher voltage rating.

Note: Refer to T495 Ordering Information on page 31 for lead

termination options.

CONSTRUCTION CAPACITOR MARKINGS

Negative Silver Adhesive Polarity

R+
Termination* Washer Stripe (+) Low
Molded Polarity ESR Polarity
Case Bevel (+) Device Indicator (+)
(Solid Stripe)
Tantalum
Wire

107 Picofarad
Code

Rated
Voltage
10K KEMET
I. D. Symbol

Tantalum
(Ta2O5)

Mn02 Coat
Weld 427
(First Layer)
Carbon Print Week Code:
(Second Layer)
Positive 1st Digit = Y ear
Silver Paint Termination* 2nd & 3rd Digits = Week
(Third Layer) "427" = The 27th week of 2004
*100% tin

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 33
 SOLID TANTALUM CHIP CAPACITORS

T495 TANTALUM CHIP CAPACITANCE VALUES

Ω ) by Capacitance & Voltage
Case Size and Max. ESR (mΩ
Capacitance Rated Voltage @ +85°C

µF Code 2.5 4 6 10 16 20 25 35 50

C,500,600 D,300
4.7 475
D,400 X,300

B,1500 D,400
6.8 685 D,275,300
C,490,500 X,300

D,300
10.0 106 T,4000 C,450 X,175,200 X,300
X,250

D,275 D,225,300
15.0 156 D,275 X,300
X,200 X,225

C, 900 D,200,250
D,225,275
22.0 226 C,290,345 D,200 D300
X,225 X,275,300

C,225,275
D,225,300
33.0 336 D,150,175, D,150,200 X,175,250
X,175
D,225,250

D,175
D,80,90,100, D,100,150, X,185,200,
47.0 476 X,100,125, X,200
200 200 300
150

V,140
B,750,900
V,300 D,150
68.0 686 D,175 C,225 X,200
D,150 X,120,150
D,90,150
X,150

V,150 V,150 D,100,125

100.0 107 T, 3000 B,700 D, 80,100 X,80,100,
C,150 X,100 125

D,80,100
C,200
150.0 157 B,900 X,85,100 X,100
X,100,125
V,150

C,225 V,150
220.0 227 D,100 D,75,100,125
X,100 X, 70,100

X,65,100 D,125
330.0 337 C,700
D,100 X,50,60

X,50, 65
470.0 477
D,125

680.0 687

1000.0 108 X,70

Note that standard values are preferred, especially where high surge currents are possible.
Extended values are available to increase capacitance and reduce ESR. Note that standard
CV values demonstrate inherently lower failure rates than extended CV values, especially in
low impedance applications.

34 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 SOLID TANTALUM CHIP CAPACITORS
T496 SERIES—Fail-Safe Fused

FEATURES
• Built-in fuse protects against damaging short • Fuse actuation, 25C: within 1 second at fault
circuit failure mode currents of 4 amps and higher.
• Precision-molded, laser-marked case • Continuous current capability: 0.75 amps
• Symmetrical, compliant terminations • Post-actuation resistance,
• Taped and reeled per EIA 481-1 25C: 10 megohms minimum
• Case geometry and footprints equivalent to • Test tabs on the sides of the case bypass the
Industrial Grade T491 Series. (Case sizes capacitor element to allow direct testing of the

Solid Tantalum Surface Mount

B, C, D and X only) fuse assembly.
• 100% Surge Current test on C, D, X sizes • RoHS Compliant & Leadfree Terminations (See
• Patented fuse assembly www.kemet.com for lead transition)

OUTLINE DRAWINGS
CATHODE (-) END SIDE VIEW ANODE (+) END BOTTOM VIEW
VIEW VIEW
B
W
B
Test Tab
0.15(0.006) Max.
H E F
K T P

S S R Termination A
X G cutout at L
KEMET’s
Option,
either end

DIMENSIONS — Millimeters (Inches)

CASE SIZE COMPONENT
± 0.20 ± 0.1 ± 0.3 ± 0.15 P R T A G E
L W H K ± (.008) F ± (.004) S ± (.012) B X
KEMET EIA (Ref) ± (.006) (Ref) (Ref) (Ref) (Ref) (Min) (Ref) (Ref)
B 3528-21 3.5 ± 0.2 2.8 ± 0.2 1.9 ± 0.2 1.1 2.2 0.8 0.4 0.10 ± 0.10 0.5 1.0 0.13 1.1 1.8 2.2
(.138 ± .008) (.110 ± .008) (.075 ± .008) (.043) (.087) (.031) (.016) (.004 ± .004) (.020) (.039) (.005) (.043) (.071) (.087)
C 6032-28 6.0 ± 0.3 3.2 ± 0.3 2.5 ± 0.3 1.4 2.2 1.3 0.5 0.10 ± 0.10 0.9 1.0 0.13 2.5 2.8 2.4
(.236 ± .012) (.126 ± .012) (.098 ± .012) (.055) (.087) (.051) (.020) (.004 ± .004) (.035) (.039) (.005) (.098) (.110) (.094)
D 7343-31 7.3 ± 0.3 4.3 ± 0.3 2.8 ± 0.3 1.5 2.4 1.3 0.5 0.10 ± 0.10 0.9 1.0 0.13 3.8 3.5 3.5
(.287 ± .012) (.169 ± .012) (.110 ± .012) (.059) (.094) (.051) (.020) (.004 ± .004) (.035) (.039) (.005) (.150) (.138) (.138)
X 7343-43 7.3 ± 0.3 4.3 ± 0.3 4.0 ± 0.3 2.3 2.4 1.3 0.5 0.10 ± 0.10 1.7 1.0 0.13 3.8 3.5* 3.5*
(.287 ± .012) (.169 ± .012) (.157 ± .012) (.091) (.094) (.051) (.020) (.004 ± .004) (.067) (.039) (.005) (.150) (.138) (.138)

Notes: 1. Metric dimensions govern.

2. (Ref) - Dimensions provided for reference only.
* Round glue pad: 2.9 ± 0.1mm (.114" ± .004") in diameter at KEMET’s option.

T496 Series – ORDERING INFORMATION

T 496 B 105 M 025 A S*
Lead Material
Tantalum H - Sn/Pb (Tin Lead) Solder-Coated
*S - 100% Sn (Tin) Plated
Series T - 100% Tin (Sn) Plated
T496 - Precision Molded, Fail-safe Failure Rate
Case Size A - Not Applicable
B, C, D, X Voltage
Capacitance Picofarad Code Capacitance Tolerance
First two digits represent significant figures. M - ± 20%
Third digit specifies number of zeros to follow. K - ± 10%
* Part Number Example: T496B105M025AS (14 digits - no spaces)
* See www.kemet.com for Pb Free transition information.

TYPICAL FUSE ACTUATION PROFILE

Current (Amps)

10

1
.0001 .001 .01 .1 1 10

Time (Seconds)
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 35
 SOLID TANTALUM CHIP CAPACITORS
T496 SERIES—Fail-Safe Fused

T496 RATINGS & PART NUMBER REFERENCE

DF ESR
Capaci- DCL A % @ +25C  @ +25C DF ESR
tance Case KEMET @ +25C 120 Hz. 100 kHz DCL µA % @ +25°C Ω @ +25°C
F Size Part Number Max. Max. Max. Capaci- Case KEMET @ 25°C 120 Hz. 100 kHz
4 Volt Rating at +85C (2.7 Volt Rating at +125C) tance µF Size Part Number Max. Max. Max.
68.0 *C T496C686(1)004AS 2.7 6.0 1.6 20 Volt Rating at +85°C (13 Volt Rating at +125°C)
100.0 *C T496C107(1)004AS 4.0 8.0 1.2
150.0 D T496D157(1)004AS 6.0 8.0 0.8 1.5 B T496B155(1)020AS 0.5 6.0 5.0
220.0 *D T496D227(1)004AS 8.8 8.0 0.7 2.2 B T496B225(1)020AS 0.5 6.0 3.5
#330.0 *D T496D337(1)004AS 13.2 8.0 0.7
330.0 *X T496X337(1)004AS 13.2 8.0 0.7 3.3 B T496B335(1)020AS 0.7 6.0 3.5
#470.0 *X T496X477(1)004AS 18.8 8.0 0.5 4.7 C T496C475(1)020AS 1.0 6.0 2.0
**6 Volt Rating at +85C (4 Volt Rating at +125C) 6.8 C T496C685(1)020AS 1.4 6.0 2.0
4.7 B T496B475(1)006AS 0.5 6.0 3.5 10.0 C T496C106(1)020AS 2.0 6.0 2.0
6.8 B T496B685(1)006AS 0.5 6.0 3.5
10.0 B T496B106(1)006AS 0.6 6.0 3.5 15.0 D T496D156(1)020AS 3.0 6.0 1.0
22.0 B T496B226(1)006AS 1.3 6.0 3.5 22.0 D T496D226(1)020AS 4.4 6.0 1.0
15.0 C T496C156(1)006AS 0.9 6.0 2.0 33.0 X T496X336(1)020AS 6.6 6.0 0.9
22.0 C T496C226(1)006AS 1.4 6.0 2.0 47.0 X T496X476(1)020AS 9.4 6.0 0.3
33.0 C T496C336(1)006AS 2.0 6.0 2.0 25 Volt Rating at +85°C (17 Volt Rating at +125°C)
47.0 D T496D476(1)006AS 2.9 6.0 1.0
47.0 *C T496C476(1)006AS 2.9 6.0 1.6 0.68 B T496B684(1)025AS 0.5 4.0 6.5
68.0 D T496D686(1)006AS 4.1 6.0 1.0 1.0 B T496B105(1)025AS 0.5 4.0 5.0
#68.0 *C T496C686(1)006AS 4.1 6.0 1.2 1.5 B T496B155(1)025AS 0.5 6.0 5.0
100.0 X T496X107(1)006AS 6.0 8.0 0.9
100.0 D T496D107(1)006AS 6.0 8.0 0.8 2.2 C T496C225(1)025AS 0.6 6.0 3.5
150.0 *D T496D157(1)006AS 9.0 8.0 0.7 3.3 C T496C335(1)025AS 0.9 6.0 2.5
#220.0 *D T496D227(1)006AS 13.2 8.0 0.7 4.7 C T496C475(1)025AS 1.2 6.0 2.5
220.0 *X T496X227(1)006AS 13.2 8.0 0.7
#330.0 *X T496X337(1)006AS 19.8 8.0 0.5 6.8 C T496C685(1)025AS 1.7 6.0 2.0
10 Volt Rating at +85C (7 Volt Rating at + 125C) 10.0 C T496C106(1)025AS 2.5 6.0 0.6
3.3 B T496B335(1)010AS 0.5 6.0 3.5 10.0 D T496D106(1)025AS 2.5 6.0 1.2
4.7 B T496B475(1)010AS 0.5 6.0 3.5 15.0 D T496D156(1)025AS 3.8 6.0 1.0
6.8 B T496B685(1)010AS 0.7 6.0 3.5
22.0 X T496X226(1)025AS 5.5 6.0 0.9
15.0 B T496B156(1)010AS 1.5 6.0 3.5
10.0 C T496C106(1)010AS 1.0 6.0 2.0 22.0 D T496D226(1)025AS 5.5 6.0 0.8
15.0 C T496C156(1)010AS 1.5 6.0 2.0 35 Volt Rating at +85°C (23 Volt Rating at +125°C)
22.0 C T496C226(1)010AS 2.2 6.0 2.0 0.47 B T496B474(1)035AS 0.5 4.0 8.0
33.0 D T496D336(1)010AS 3.3 6.0 1.0 0.68 B T496B684(1)035AS 0.5 4.0 6.5
33.0 *C T496C336(1)010AS 3.3 6.0 1.6
47.0 D T496D476(1)010AS 4.7 6.0 1.0 1.0 B T496B105(1)035AS 0.5 4.0 5.0
#47.0 *C T496C476(1)010AS 4.7 6.0 1.2 1.5 C T496C155(1)035AS 0.5 6.0 4.5
68.0 X T496X686(1)010AS 6.8 6.0 0.9
68.0 D T496D686(1)010AS 6.8 6.0 0.8 2.2 C T496C225(1)035AS 0.8 6.0 3.5
100.0 D T496D107(1)010AS 10.0 8.0 0.7 3.3 C T496C335(1)035AS 1.2 6.0 2.5
150.0 *X T496X157(1)010AS 15.0 8.0 0.7 4.7 D T496D475(1)035AS 1.7 6.0 1.5
#150.0 *D T496D157(1)010AS 15.0 8.0 0.7
#220.0 *X T496X227(1)010AS 22.0 8.0 0.5 6.8 D T496D685(1)035AS 2.4 6.0 1.3
16 Volt Rating at +85C (10 Volt Rating at +125C) 10.0 X T496X106(1)035AS 3.5 6.0 1.0
2.2 B T496B225(1)016AS 0.5 6.0 3.5 15.0 *X T496X156(1)035AS 5.3 6.0 0.9
3.3 B T496B335(1)016AS 0.5 6.0 3.5 50 Volt Rating at +85°C (33 Volt Rating at +125°C)
4.7 B T496B475(1)016AS 0.8 6.0 3.5
0.15 B T496B154(1)050AS 0.5 4.0 16.0
10.0 B T496B106(1)016AS 1.6 6.0 3.5
0.22 B T496B224(1)050AS 0.5 4.0 14.0
6.8 C T496C685(1)016AS 1.1 6.0 2.0
10.0 C T496C106(1)016AS 1.6 6.0 2.0 0.33 B T496B334(1)050AS 0.5 4.0 10.0
15.0 C T496C156(1)016AS 2.4 6.0 2.0 0.47 C T496C474(1)050AS 0.5 4.0 8.0
22.0 D T496D226(1)016AS 3.6 6.0 1.0 0.68 C T496C684(1)050AS 0.5 4.0 7.0
22.0 *C T496C226(1)016AS 3.6 6.0 1.6
33.0 D T496D336(1)016AS 5.3 6.0 1.0 1.0 C T496C105(1)050AS 0.5 4.0 5.5
47.0 X T496X476(1)016AS 7.5 6.0 0.9 1.5 C T496C155(1)050AS 0.8 6.0 5.0
47.0 D T496D476(1)016AS 7.5 6.0 0.8 2.2 D T496D225(1)050AS 1.1 6.0 2.5
100.0 *X T496X107(1)016AS 16.0 8.0 0.7 3.3 D T496D335(1)050AS 1.7 6.0 2.0
** Note: 6V rating equivalent to 6.3 rating *Extended Ratings
(1) To complete KEMET Part Number, insert M for ±20% tolerance or K for
# Maximum capacitance change @ 125C = +15% (all others =12%)
±10% tolerance.
Higher voltage ratings and tighter capacitance tolerance product may
T496 SERIES CONSTRUCTION be substituted within the same size at KEMET’s option. Voltage substi-
Negative Silver Adhesive
tutions will be marked with the higher voltage rating.
Termination* Washer Polarity
Molded
Stripe (+)
Polarity CAPACITOR MARKING
Case Bevel (+)
Fused
Fuse
Fail-Safe
Device F+ Polarity
Indicator (+)
(Solid Stripe)

227 Picofarad
Code

Tantalum
(Ta2O5) Weld
Rated
Voltage 20K KEMET
I. D. Symbol
Mn02 Coat
(First Layer)
Carbon
(Second Layer)
Positive
Termination*
442
Silver Paint Tantalum
(Third Layer)
Wire *100% Tin
Print Week Code:
1st Digit = Year
2nd & 3rd Digits = Week
"442" = The 42nd week of 2004

36 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 SOLID TANTALUM CHIP CAPACITORS
T510 SERIES—Ultra-Low ESR
FEATURES
• Ultra Low ESR < 30 mΩ • 100% accelerated steady-state aging
• New E/7260 Case with ESR < 18 mΩ • 100% Surge current test
• Up to 4 Amps ripple current • Precision - molded, laser-marked case
• RoHS Compliant & Leadfree Termination (see • Symmetrical compliant terminations
www. kemet.com for lead transitions) • Taped and reeled per EIA 481-1
OUTLINE DRAWING
CATHODE (-) END SIDE VIEW ANODE (+) END BOTTOM VIEW

Solid Tantalum Surface Mount

VIEW VIEW
B
W
B

H E F
K T P

S S R Termination A
X G cutout at L
KEMET’s
Option,
either end

DIMENSIONS - Millimeters (Inches)

CASE SIZE COMPONENT
± 0.20 ± 0.1 ± 0.3 B ± 0.15 X P R T A G E
KEMET EIA L W H K ± (.008) F ± (.004) S ± (.012) (Ref) ± (.006) (Ref) (Ref) (Ref) (Ref) (Min) (Ref) (Ref)
X 7343-43 7.3 ± 0.3 4.3 ± 0.3 4.0 ± 0.3 2.3 2.4 1.3 0.5 0.10 ± 0.10 0.9 1.0 0.13 3.8 3.5 3.5
(.287 ± .012) (.169 ± .012) (.157 ± .012) (.091) (.094) (.051) (.020) (.004 ± .004) (.035) (.039) (.005) (.150) (.138) (.138)
E 7260-38 7.3 ± 0.3 6.0 ± 0.3 3.6 ± 0.2 2.3 4.1 1.3 0.5 0.10 ± 0.10 0.9 1.0 0.13 3.8 3.5 3.5
(.287 ± .012) (.236 ± .012) (.142 ± .008) (.091) (.161 (.051) (.020) (.004 ± .004) (.035) (.039) (.005) (.150) (.138) (.138)
Notes: Metric Dimensions govern
(Ref) - Dimensions provided for reference only.
T510 RATINGS & PART NUMBER REFERENCE
DC Leakage ESR m Ω @
Capaci- Case µA @ 25°C DF % @ 25°C 100 kHz Ripple Current A rms @ 25°C
tance µF Size KEMET Part Number Max 25°C Max Max 100 kHz, max
25°C 85°C 125°C
4 Volt Rating at +85°C (2.7 Volt Rating at 125°C)
680.0 X T510X687(1)004AS 27.2 6.0 30.0 3.0 2.7 1.2
1000.0 X T510X108(1)004AS 40.0 6.0 18.0 3.9 3.5 1.5
1000.0 E T510E108(1)004AS 40.0 6.0 18.0 4.0 3.6 1.6
1000.0 E T510E108(1)004AS4115 40.0 6.0 10.0 5.3 4.8 2.1
6/6.3 Volt Rating at +85°C (4 Volt Rating at 125°C)
470.0 X T510X477(1)006AS 28.2 6.0 30.0 3.0 2.7 1.2
680.0 E T510E687(1)006AS 40.8 6.0 23.0 3.5 3.2 1.4
680.0 E T510E687(1)006AS4115 40.8 6.0 12.0 4.8 4.3 1.9
10 Volt Rating at +85°C (7 Volt Rating at 125°C)
330.0 X T510X337(1)010AS 33.0 6.0 35.0 2.8 2.5 1.1
25 Volt Rating at +85°C (17 Volt Rating at 125°C)
100.0 E T510E107(1)025AS 25.0 8.0 50.0 2.4 2.1 1.0
(1) To complete the KEMET part number, insert “K” – 10% or “M” – 20% capacitance tolerance.
Note: Refer to T510 Ordering Information for lead termination options.

T510 ORDERING INFORMATION

T 510 X 477 M 006 A S
Lead Material
Tantalum *S - 100% Tin (Sn) Plated
H - Standard Solder -Coated (SnPb)
Series T - 100% Tin (Sn) Plated
T510 - Ultra-Low ESR Failure Rate
Case Size A - Not Applicable
X, E Voltage
Capacitance Picofarad Code Capacitance Tolerance
First two digits represent significant figures. M - ± 20%
Third digit specifies number of zeros to follow. K - ± 10%
*See www.kemet.com for Pb Free transition information.
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 37
 SOLID TANTALUM CHIP CAPACITORS
T510 Series - Ultra-Low ESR

TYPICAL CAP FREQUENCY SCAN @25˚C TYPICAL ESR/Z FREQUENCY SCAN @25˚C
T510X477M006AS T510X477M006AS
500 10

450

400

) (Ω)
350
1
Capacitance (µF)

300

Z(
250

200

)
.1
150

ESR (
100

50
0 .01
100Hz 1kHz 10kHz 100kHz 1MHz 100Hz 1kHz 10kHz 100kHz 1MHz

T510
CAPACITOR MARKINGS

Ultra-Low
ESR Device M+ Polarity
Indicator (+)
(Solid Stripe)

477 Picofarad
Code
Rated
Voltage 6K KEMET
I. D. Symbol

1st Digit
=Year
414 2nd & 3rd Digits
= Week

“414” = The 14th week

of 2004.

T510X SERIES CONSTRUCTION

Negative Silver Adhesive
Termination* Washer Polarity
Stripe (+)
Molded Polarity
Case Bevel (+)

Weld

Tantalum
(Ta2O5)

Silver Paint
(Third Layer) Carbon Positive
(Second Layer) Termination*
MnO2 Coat Tantalum *100% Tin
(First Layer) Wire

38 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 SOLID TANTALUM CHIP CAPACITORS
T510 Series - Ultra-Low ESR

TYPICAL CAP FREQUENCY SCAN @ 25°C TYPICAL ESR/Z FREQUENCY SCAN @ 25°C
T510E108M004AS T510E108M004AS
1500 10

1400

1300

) (Ω)
1200

Solid Tantalum Surface Mount

1
Capacitance (µF)

1100

Z(
1000

)
900
.1

ESR (
800

700

600

500 .01
100Hz 1kHz 10kHz 100kHz 1MHz 100Hz 1kHz 10kHz 100kHz 1MHz

T510E
CAPACITOR MARKINGS
CAPACITOR MARKINGS

Ultra-Low
ESR Device M+ Polarity
Indicator (+)
(Solid Stripe)

Rated
108 Picofarad
Code

Voltage
4K KEMET
I. D. Symbol

1st Digit
=Year
435 2nd & 3rd Digits
= Week

“435” = The 35th week

of 2004.

T510E SERIES CONSTRUCTION

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 39
 POLYMER TANTALUM CHIP CAPACITORS

COMPONENT PERFORMANCE CHARACTERISTICS

Introduction 4. Voltage Ratings
KEMET has developed a new type of tantalum capacitor that • 2V-25V DC Rated Voltage
replaces the solid manganese dioxide electrode with a solid This is the maximum peak DC operating voltage from
conductive polymer. This product is named the KO-CAP for -55ºC to +105ºC for continuous duty. Above 105ºC, this
KEMET Organic Capacitor. The basic families are the T520, voltage is derated linearly to 2/3 rated voltage for
T525 and T530 series. A separate detail of performance operation at 125ºC for T525 and T530 Series.
characteristics is presented here as there are some differ- • Surge Voltage Ratings
ences between the polymer tantalums and the standard Surge voltage capability is demonstrated by applica-
MnO2 types. Like all KEMET tantalum chips, these series tion of 1000 cycles of the relevant voltage, at 25ºC,
are 100% screened for all electrical parameters: 85ºC or 105ºC. The parts are charged through a 33
Capacitance @ 120 Hz, Dissipation Factor (DF) @ 120 Hz, ohm resistor for 30 seconds and then discharged
ESR @ 100 kHZ and DC Leakage. It is also 100% surge cur- through a 33 ohm resistor for 30 seconds for each
rent tested at full rated voltage through a low impedance cir- cycle.Surge voltage is the maximum voltage to which
cuit. The advantages of the polymer include very low ESR the part can be subjected under transient conditions
and elimination of the potentially catastrophic failure mode including the sum of peak AC ripple, DC bias and any
that may occur with standard tantalum capacitors in a high transients.
current application. Although the natural KO-CAP series fail-
• Voltage Ratings • Table 1
ure mechanism is a short circuit, it does not exhibit an
Rated Surge Derated Derated
explosive failure mode.
Voltage Voltage Voltage Surge
Voltage
ELECTRICAL -55ºC to +105ºC +125ºC
1. Operating Temperature Range 2V 2.6V 1.6V 2.1V
• -55ºC to +105ºC for T520; -55ºC to +125ºC for 2.5V 3.3V 2.0V 2.6V
T525 and T530 3V 3.9V 2.4V 3.1V
For T525 and T530 Series above 105ºC, the 4V 5.2V 3.2V 4.2V
voltage rating is reduced linearly from 1.0 x rated volt- 6.3V 8.2V 5V 6.5V
age to 0.8 x rated voltage at 125ºC. 8V 10.4V 6.4V 8.3V
10V 13V 8V 10.4V
2. Non-Operating Temperature Range
16V 20.8V 12.8V 16.6V
• -55ºC to +105ºC for T520
• -55ºC to +125ºC for T525 and T530 25V 32.5V 20V 26V
5. Reverse Voltage Rating & Polarity
3. Capacitance and Tolerance Polymer tantalum capacitors are polar devices and
• 15µF to 1500µF may be permanently damaged or destroyed if con-
• ±20% Tolerance nected in the wrong polarity. The positive terminal is
Capacitance is measured at 120 Hz, up to 1.0 volt rms identified by a laser-marked stripe and may also
maximum and up to 2.5V DC maximum. DC bias causes include a beveled edge. These capacitors will with-
only a small reduction in capacitance, up to about 2% stand a small degree of transient voltage reversal for
when full rated voltage is applied. DC bias is not common- short periods as shown in the following table. Please
ly used for room temperature measurements but is more note that these parts may not be operated continu-
commonly used when measuring at temperature extremes. ously in reverse, even within these limits.
Capacitance does decrease with increasing frequency, but Table 2
not nearly as much or as quickly as standard tantalums. Temperature Permissible Transient Reverse Voltage
Figure 1 compares the frequency induced cap roll-off 25ºC 15% of Rated Voltage
between the KO-CAP and traditional MnO2 types. 55ºC 10% of Rated Voltage
Capacitance also increases with increasing temperature. 85ºC 5% of Rated Voltage
See section 12 for temperature coefficients. 105ºC 3% of Rated Voltage
6. DC Leakage Current
Capacitance (uF)
150
Because of the high conductivity of the polymer, the
KO-CAP family has higher leakage currents than tradi-
tional MnO2 type Tantalum caps. The DC Leakage
100 limits at 25ºC are calculated as 0.1 x C x V, where C is
Polymer cap in µF and V is rated voltage in Volts. Limits for all
MnO 2
50
part numbers are listed in the ratings tables.
DC Leakage current is the current that flows through
the capacitor dielectric after a five minute charging
0
10 1,000 100,000 10,000,000 period at rated voltage. Leakage is measured at 25ºC
100 10,000 1,000,000 100,000,000
Frequency (Hz)
with full rated voltage applied to the capacitor through
a 1000 ohm resistor in series with the capacitor.
FIGURE 1

40 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 POLYMER TANTALUM CHIP CAPACITORS

COMPONENT PERFORMANCE CHARACTERISTICS

DC Leakage current does increase with tempera- 9. Equivalent Series Resistance (ESR) and
ture. The limits for 85ºC @ Rated Voltage and Impedance (Z)
105ºC @ 0.8 x Rated Voltage are both 10 times The Equivalent Series Resistance (ESR) of the KO-
the 25ºC limit. CAP is much lower than standard Tantalum caps
because the polymer cathode has much higher
7. Surge Current Capability conductivity. ESR is not a pure resistance, and it
Certain applications may induce heavy surge cur- decreases with increasing frequency.
rents when circuit impedance is very low (<0.1
ohm per volt). Driving inductance may also cause Total impedance of the capacitor is the vector
voltage ringing. Surge currents may appear as sum of capacitive reactance (XC) and ESR, below
transients during turn-on of equipment. resonance; above resonance total impedance is
the vector sum of inductive reactance (X L) and
The KO-CAP has a very high tolerance for surge
current. And although the failure mechanism is a ESR.
short circuit, they do not ignite as may occur with
standard tantalums in such applications.
The KO-CAP series receives 100% screening for
surge current in our production process.
Capacitors are surged 4 times at full rated voltage
applied through a total circuit resistance of <0.5

Polymer Tantalum Surface Mount

ohms. Failures are removed during subsequent
electrical testing.
XC = 1 ohm
8. Dissipation Factor (DF) 2fC
Refer to part number tables for maximum DF
limits. where:
f = frequency, Hertz
Dissipation factor is measured at 120 Hz, up to 1.0 C = capacitance, Farad
volt rms maximum, and up to 2.5 volts DC maxi-
mum at +25ºC. The application of DC bias causes
a small reduction in DF, about 0.2% when full FIGURE 2a Total Impedance of the Capacitor Below
rated voltage is applied. DF increases with Resonance
increasing frequency.
Dissipation factor is the ratio of the equivalent
series resistance (ESR) to the capacitive reac-
tance, (XC) and is usually expressed as a percent-
age. It is directly proportional to both capacitance
and frequency. Dissipation factor loses its impor-
tance at higher frequencies, (above about 1 kHz),
where impedance (Z) and equivalent series resis-
tance (ESR) are the normal parameters of concern. XL = 2fL
DF = R = 2 f CR DF= Dissipation Factor
where:
XC R= Equivalent Series f = frequency, Hertz
Resistance (Ohms) L = inductance, Henries
XC= Capacitive Reactance
(Ohms)
f= Frequency (Hertz)
C= Series Capacitance FIGURE 2b Total Impedance of the Capacitor Above
(Farads) Resonance

DF is also referred to as tan  or “loss tangent.” To understand the many elements of a capaci-
The “Quality Factor,” “Q,” is the reciprocal of DF. tor, see Figure 3.

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 41
 POLYMER TANTALUM CHIP CAPACITORS

COMPONENT PERFORMANCE CHARACTERISTICS

ESR and Impedance
T495D 150 uF (MnO2 ) vs. T520D 150 uF (Polymer)
Impedance & ESR (Ohms)
L RS C 100

10
RL
1

Cd Rd MnO 2
0.1

FIGURE 3 The Real Capacitor

Polymer
0.01
A capacitor is a complex impedance consisting 100 1,000 10,000 100,000 1,000,000 10,000,000

of many series and parallel elements, each Frequency (Hz)

FIGURE 4
adding to the complexity of the measurement
system. 10. AC Power Dissipation
L — Represents lead wire and construction Power dissipation is a function of capacitor size
inductance. In most instances (especially in and materials. Maximum power ratings have been
solid tantalum and monolithic ceramic capaci- established for all case sizes to prevent overheat-
tors) it is insignificant at the basic measurement ing. In actual use, the capacitor’s ability to dissi-
frequencies of 120 and 1000 Hz. pate the heat generated at any given power level
may be affected by a variety of circuit factors.
RS — Represents the actual ohmic series resis- These include board density, pad size, heat sinks
tance in series with the capacitance. Lead wires and air circulation.
and capacitor electrodes are contributing
sources. Table 3
Tantalum Chip Power Dissipation Ratings
RL — Capacitor Leakage Resistance. Typically it Case Code Maximum Power Dissipation
can reach 50,000 megohms in a tantalum KEMET EIA mWatts @ +25ºC w/+20ºC Rise
capacitor. It can exceed 1012 ohms in monolithic T520/T 3528-12 70
ceramics and in film capacitors. T52x/B 3528-21 85
Rd — The dielectric loss contributed by dielectric T520/V 7343-20 125
absorption and molecular polarization. It T52x/D 7343-31 150
becomes very significant in high frequency mea- T520/Y 7343-40 161
surements and applications. Its value varies with T520/X 7343-43 165
frequency. T530/D 7343-31 255
T530/Y 7343-40 263
Cd — The inherent dielectric absorption of the
solid tantalum capacitor which typically equates T530/X 7343-43 270
to 1-2% of the applied voltage. T530/E 7260-38 285

As frequency increases, X C continues to 11. AC Operation

decrease according to its equation above. There Permissible AC ripple voltage and current are
is unavoidable inductance as well as resistance related to equivalent series resistance (ESR) and
in all capacitors, and at some point in frequency, power dissipation capability.
the reactance ceases to be capacitive and
becomes inductive. This frequency is called the Permissible AC ripple voltage which may be
self-resonant point. In solid tantalum capacitors, applied is limited by three criteria:
the resonance is damped by the ESR, and a
smooth, rather than abrupt, transition from a. The positive peak AC voltage plus the DC bias
capacitive to inductive reactance follows. voltage, if any, must not exceed the DC voltage
rating of the capacitor.
Figure 4 compares the frequency response of a
KO-CAP to a standard Tantalum chip. See also b. The negative peak AC voltage, in combination
frequency curves shown in the T520 section, with bias voltage, if any, must not exceed the
p.46. Maximum limits for 100 kHz ESR are listed permissible reverse voltage ratings presented
in the part number tables for each series. in Section 5.
The T530 Capacitance, Impedance and ESR vs. c. The power dissipated in the ESR of the capaci-
Frequency Comparisions are located on page tor must not exceed the appropriate value
52. Maximum limits for 100 kHz are listed in the specified in Section 10.
part number table on page 51.
42 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 POLYMER TANTALUM CHIP CAPACITORS

COMPONENT PERFORMANCE CHARACTERISTICS

Actual power dissipated may be calculated from 14. High Temperature Life Test
the following: • 105ºC, 0.8 x Rated Voltage, 2000 hours, 125ºC
P =I2R for T525, T530 Series
Substituting I = E, P = E2R Post Test Performance:
Z Z2 a. Capacitance: within -20%/+10% of initial value
b. DF: within initial limit
where: c. DC Leakage: within 1.25 initial limits for T520;
I = rms ripple current (amperes) 2 x initial limit for T525, T530
E = rms ripple voltage (volts) d. ESR: within 2 x initial limit for T520, T530
P = power (watts) ESR: within initial limit for T525
Z = impedance at specified frequency (ohms)
15. Storage Life Test
R = equivalent series resistance at specified
• 105ºC, 0VDC, 2000 Hours for T520; 125ºC for
frequency (ohms) T525, T530
Using P max from Table 3, maximum allowable Post Test Perfomance:
rms ripple current or voltage may be determined as a. Capacitance: within -20%/+10% of initial value
follows: b. DF: within initial limit
I(max) = P max/R E(max) = Z P max/R c. DC Leakage: within 1.25 initial limits for T520;
These values should be derated at elevated tem- 2 x initial limit for T525, T530
peratures as follows: d. ESR: within 2 x initial limit for T520, T530
Temperature Derating Factor ESR: within initial limit for T525
85ºC .9 16. Thermal Shock

Polymer Tantalum Surface Mount

125ºC .4 • Mil-Std-202, Method 107, Condition B
Minimum temperature is -55ºC
ENVIRONMENTAL Maximum temperature is +105ºC for T520; 125ºC
for T525, T530
12. Temperature Stability 500 Cycles
Mounted capacitors withstand extreme tempera- Post Test Performance:
ture testing at a succession of continuous steps a. Capacitance: within +10%/-20% of initial value
at +25ºC, -55ºC, +25ºC, +85ºC, +105ºC, +25ºC in b. DF: within initial limit
that order*. Capacitors are allowed to stabilize at c. DC Leakage: within initial limit
each temperature before measurement. Cap, DF, d. ESR: within 2 x initial limit
and DCL are measured at each temperature
17. Moisture Resistance Testing
except DC Leakage is not measured at -55ºC.
• J-Std-020
*Maximum temperature 125ºC for T525 and T530 series.
Steps 7a and 7b excluded, 0V, 21 cycles
Table 4 Post Test Performance:
Acceptable limits are as follows: a. Capacitance: within ±30% of initial value
b. DF: within initial limit
Step Temp. ∆Cap DCL DF
c. DC Leakage: within initial limit
1 +25ºC Specified Catalog Catalog d. ESR: within initial limit
Tolerance Limit Limit e. Meets MSL Level 3
2 -55ºC ±20% of N/A Catalog
initial value Limit 18. Load Humidity
• 85ºC, 85% RH, Rated Voltage, 500 Hours
3 +25ºC ±10% of Catalog Catalog
Post Test Performance:
initial value Limit Limit a. Capacitance: within +35%/-5% of initial value
4 +85ºC ±20% of 10x Catalog 1.2x Catalog b. DF: within initial limit
initial value Limit Limit c. DC Leakage: within 5 x initial limit
5 +105ºC ±30% of 10x Catalog 1.5x Catalog d. ESR: within 2 x initial limit
(125ºC for initial value Limit Limit
19. ESD
T525, T530)
• Polymer tantalum capacitors are not sensitive
6 +25ºC ±10% of Catalog Catalog to Electro-Static Discharge (ESD).
initial value Limit Limit
20. Failure Mechanism and Reliability
13. Standard Life Test The normal failure mechanism is dielectric break-
• 85ºC, Rated Voltage, 2000 Hours down. Dielectric failure can result in high DC
Post Test Performance: Leakage current and may proceed to the level of a
a. Capacitance: within -20%/+10% of initial value short circuit. With sufficient time to charge, heal-
b. DF: within initial limit ing may occur by one of two potential mecha-
c. DC Leakage: within initial limit nisms. The polymer adjacent to the dielectric fault
d. ESR: within initial limit site may overheat and vaporize, disconnecting the
fault site from the circuit. The polymer may also
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 43
 POLYMER TANTALUM CHIP CAPACITORS

COMPONENT PERFORMANCE CHARACTERISTICS

oxidize into a more resistive material that elimi- 26. Vibration
nates the defect site in the dielectric and reduces • Mil-Std-202, Method 204, Condition D, 10 Hz
the flow of current. to 2,000 Hz, 20G Peak
Post Test Performance:
Capacitor failure may be induced by exceeding a. Capacitance — within ±10% of initial value
the rated conditions of forward DC voltage, b. DC Leakage — within initial limit
reverse DC voltage, surge current, power dissipa- c. Dissipation Factor — within initial limit
tion or temperature. Excessive environmental d. ESR — within initial limit
stress, such as prolonged or high temperature
reflow processes may also trigger dielectric failure. 27. Shock
• Mil-Std-202, Method 213, Condition I,
Failure rates may be improved in application by 100 G Peak
derating the voltage applied to the capacitor. Post Test Performance:
KEMET recommends that KO-CAPs be derated a. Capacitance — within ±10% of initial value
b. DC Leakage — within initial limit
to 90% or less of the rated voltage in application
c. Dissipation Factor — within initial limit
for part types ≤ 10V. Parts > 10V should be derat- d. ESR - within initial limit
ed to 80% or less of the rated voltage.
28. Terminal Strength
KO-CAPs exhibit a benign failure mode in that • Pull Force
they do not fail catastophically even under typical • One Pound (454 grams), 30 Seconds
fault conditions. If a shorted capacitor is allowed
to pass unlimited current, it may overheat and the
case may discolor. But this is distinctly different
from the “ignition” that may occur with standard
MnO2 cathode tantalums. Replacement of the
MnO2 by the polymer removes the oxygen that
fuels ignition during a failure event. • Tensile Force
• Four Pounds (1.8 kilograms), 60 Seconds
MECHANICAL
21. Resistance to Solvents
• Mil-Std-202, Method 215
Post Test Performance:
a. Capacitance — within ±10% of initial value
b. DC Leakage — within initial limit
c. Dissipation Factor — within initial limit
d. ESR — within initial limit
4 lb. (1.8 Kg)
e. Physical — no degradation of case, terminals
or marking • Shear Force
Table 5 Maximum Shear Loads
22. Fungus Case Code Maximum Shear Loads
• Mil-Std-810, Method 508 KEMET EIA Kilograms Pounds
T 3528-12 3.6 8.0
23. Flammability B 3528-21 3.6 8.0
• UL94 VO Classification V 7343-20 5.0 11.0
Encapsulant materials meet this classifaction D 7343-31 5.0 11.0
Y 7343-40 5.0 11.0
24. Resistance to Soldering Heat X 7343-43 5.0 11.0
• Maximum Reflow
+240 ±5ºC, 10 seconds Post Test Performance:
• Typical Reflow a. Capacitance — within ±5% of initial value
+230 ±5ºC, 30 seconds b. DC Leakage — within initial limit
Post Test Performance: c. Dissipation Factor — within initial limit
a. Capacitance — within ±10% of initial value d. ESR - within initial limit
b. DC Leakage — within initial limit
c. Dissipation Factor — within initial limit
d. ESR — within initial limit
25. Solderability
• Mil-Std-202, Method 208
• ANSI/J-STD-002, Test B
Applies to Solder Coated terminations only.
44 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 POLYMER TANTALUM CHIP CAPACITORS

COMPONENT PERFORMANCE CHARACTERISTICS

APPLICATIONS
Hand-soldering should be avoided. If necessary, it
29. Handling should be performed with care due to the difficulty in
Automatic handling of encapsulated components is process control. Care should be taken to avoid contact
enhanced by the molded case which provides compat- of the soldering iron to the molded case. The iron
ibility with all types of high speed pick and place should be used to heat the solder pad, applying solder
equipment. Manual handling of these devices presents between the pad and the termination, until reflow
no unique problems. Care should be taken with your occurs. The iron should be removed. “Wiping” the
fingers, however, to avoid touching the solder-coated edges of a chip and heating the top surface is not rec-
terminations as body oils, acids and salts will degrade ommended.
the solderability of these terminations. Finger cots
should be used whenever manually handling all During typical reflow operations a slight darkening of
solderable surfaces. the gold-colored epoxy may be observed. This slight
darkening is normal and is not harmful to the product.
30. Termination Coating Marking permanency is not affected by this change.
After May 1, 2004, the standard finish coating for T520,
T525 and T530 is transitioning to 100% tin. 33. Washing
Standard washing techniques and solvents are com-
31. Recommended Mounting Pad Geometries patible with all KEMET surface mount tantalum capaci-
Proper mounting pad geometries are essential for tors. Solvents such as Freon TMC and TMS,
successful solder connections. These dimensions are Trichlorethane, methylene chloride, prelete, and iso-
highly process sensitive and should be designed to propyl alcohol are not harmful to these components.
maximize the intergrity of the solder joint, and to Please note that we are not endorsing the use of

Polymer Tantalum Surface Mount

minimize component rework due to unacceptable sol- banned or restricted solvents. We are simply stating
der joints. that they would not be harmful to the components.
Figure 5 illustrates pad geometry. The table provides If ultrasonic agitation is utilized in the cleaning process,
recommended pad dimensions for reflow soldering care should be taken to minimize energy levels and
techniques. These dimensions are intended to be a exposure times to avoid damage to the terminations.
starting point for circuit board designers, to be fine
tuned, if necessary, based upon the peculiarities of the KEMET tantalum chips are also compatible with newer
soldering process and/or circuit board design. aqueous and semi-aqueous processes.

Contact KEMET for Engineering Bulletin Number 34. Encapsulations

F-2100 entitled “Surface Mount Mounting Pad Under normal circumstances, potting or encapsulation
Dimensions and Considerations” for further details on of KEMET tantalum chips is not required.
this subject. 35. Storage Environment
Tantalum polymer series (T520, T525, T530) are
C
shipped in moisture barrier bags with a desiccant and
moisture indicator card. These series are classified as
Grid
Placement MSL (Moisture Sensitivity Level 3). Upon opening the
X
Courtyard moisture barrier bag, parts should be mounted within 7
days to prevent moisture absorption and outgassing. If
G the 7 day window is exceeded, the parts can be baked
Y
per the instructions on the bag (168 hours at 40±5ºC).
Z
Figure 5
Tantalum chip capacitors should be stored in normal
working environments. While the chips themselves are
quite robust in other environments, solderability will be
Table 6 - Land Pattern Dimensions for Reflow Solder degraded by exposure to high temperatures, high
Pad Dimensions humidity, corrosive atmospheres, and long term
KEMET/EIA Size Code Y C storage. In addition, packaging materials will be
Z G X (ref) (ref) degraded by high temperature - reels may soften or
B/3528-21, T/3528-12 5.00 1.10 2.50 1.95 3.05 warp, and tape peel force may increase. KEMET
D/7343-31, V/7343-20, 8.90 3.80 2.70 2.55 6.35 recommends that maximum storage temperature not
X/7343-43, Y/7343-40 exceed 40 degrees C, and the maximum storage
humidity not exceed 60% relative humidity. In
32. Soldering addition, temperature fluctuations should be minimized
The T52X KO-CAP family has been designed for reflow to avoid condensation on the parts, and atmospheres
solder processes. Solder-coated terminations have should be free of chlorine and sulfur bearing
excellent wetting characteristics for high integrity sol- compounds. For optimized solderability, chip stock
der fillets. Preheating of these components is recom- should be used promptly, preferably within 1.5 years
mended to avoid extreme thermal stress. The maxi- of receipt.
mum recommended preheat rate is 2ºC per second.
See page 14 for SnPb soldering profile.
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 45
 POLYMER TANTALUM CHIP CAPACITORS
T520 Series - KO Cap
FEATURES
• Polymer Cathode Technology • Use Up to 80% of Rated Voltage (20% Derating)
• Low ESR for part types > 10 Volts
• High Frequency Cap Retention • Capacitance 15 to 1000µF (±20%)
• No-Ignition Failure Mode • Voltage 2V to 25V
• Use Up to 90% of Rated Voltage (10% Derating) • EIA Standard Case Sizes
for part types ≤ 10 Volts • 100% Surge Current Tested
• Halogen Free Epoxy • Operating Temperature -55ºC to +105ºC
• 100% Accelerated Steady State Aging • Self Healing Mechanism
• Volumetrically Efficient • RoHS Compiant & Leadfree Terminations (see
www.kemet.com for lead transition)
OUTLINE DRAWING
CATHODE (-) END SIDE VIEW ANODE (+) END BOTTOM VIEW
VIEW VIEW

H E F
K T

A
X S G S
L

DIMENSIONS - MILLIMETERS
Case Size
KEMET EIA L W H K ±0.20 F ±0.1 S ±0.3 X(Ref) T(Ref) A(Min) G(ref) E(ref)
A 3216-18 3.2 ± 0.2 1.6 ± 0.2 1.6 ± 0.2 0.9 1.2 0.8 0.10 ± 0.10 0.13 0.8 1.1 1.3
T 3528-12 3.5 ± 0.2 2.8 ± 0.2 1.2 max 0.3 2.2 0.8 0.05 0.13 1.1 1.8 2.2
B 3528-21 3.5 ± 0.2 2.8 ± 0.2 1.9 ± 0.2 0.9 2.2 0.8 0.10 ± 0.10 0.13 1.1 1.8 2.2
C 6032-28 6.0 ± 0.3 3.2 ± 0.3 2.5 ± 0.3 1.4 2.2 1.3 0.10 ± 0.10 0.13 2.5 2.8 2.4
W 7343-15 7.3 ± 0.3 4.3 ± 0.3 1.5 max 0.6 2.4 1.3 0.05 0.13 3.8 3.5 3.5
V 7343-20 7.3 ± 0.3 4.3 ± 0.3 1.9 max 0.9 2.4 1.3 0.05 0.13 3.8 3.5 3.5
D 7343-31 7.3 ± 0.3 4.3 ± 0.3 2.8 ± 0.3 1.5 2.4 1.3 0.10 ± 0.10 0.13 3.8 3.5 3.5
Y 7343-40 7.3 ± 0.3 4.3 ± 0.3 4.0 max 1.9 2.4 1.3 0.10 ± 0.10 0.13 3.8 3.5 3.5
X 7343-43 7.3 ± 0.3 4.3 ± 0.3 4.0 ± 0.3 2.3 2.4 1.3 0.10 ± 0.10 0.13 3.8 3.5 3.5

T520 ORDERING INFORMATION

T 520 V 157 M 006 A S E015
Tantalum ESR
Lead Material
Series *S - 100% Tin (Sn) Plated
T520 - Low ESR Polymer H - Standard Solder Coated
T - 100% Tin (Sn) Plated
Case Size
A, T, B, C, W, V, D, Y, X Failure Rate
A - Not Applicable
Capacitance Picofarad Code Voltage
First two digits represent significant figures.
Third digit specifies number of zeros to follow.
Capacitance Tolerance
M = ± 20%
*See www.kemet.com for Pb Free transition information.
T520 SERIES CONSTRUCTION
COMPONENT MARKING

KEMET Polarity (+)

Organic KO Indicator

Picofarad
157 Code
Rated
Voltage 6K KEMET ID

412 PWC
*100% Tin

412 = 12th week of 2004

46 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 POLYMER TANTALUM CHIP CAPACITORS
T520 Series - KO Cap
T520 RATINGS & PART NUMBER REFERENCE
Ripple Current
DF% @ Arms @
DC Leakage ESR mΩ @
Capaci- Case 25°C 120 100 kHz Max
KEMET Part Number µA @ 25°C 25°C 100 kHz
tance µF Size Hz
Max Max w/∆T=20°C
Max w/∆T= 2°C
@ -55°C
@ 105°C
to 85°C
2 Volt Rating @ 105°C
470.0 V T520V477M002A(1)E040 94 10 40 1.8 0.6
2.5 Volt Rating @ 105°C
56.0 T T520T566M2R5A(1)E070 14 8 70 1.0 0.3
68.0 A T520A686M2R5A(1)E080 17 8 80 1.0 0.3
100.0 T T520T107M2R5A(1)E070 25 8 70 1.0 0.3
100.0 B T520B107M2R5A(1)E040 25 8 40 1.5 0.5
100.0 B T520B107M2R5A(1)E070 25 8 70 1.1 0.3
220.0 B T520B227M2R5A(1)E035 55 8 35 1.6 0.5
220.0 B T520B227M2R5A(1)E070 55 8 70 1.1 0.3
220.0 V T520V227M2R5A(1)E009 55 10 9 3.7 1.2
220.0 V T520V227M2R5A(1)E012 55 10 12 3.2 1.0
220.0 V T520V227M2R5A(1)E015 55 10 15 2.9 0.9
220.0 V T520V227M2R5A(1)E025 55 10 25 2.2 0.7
220.0 V T520V227M2R5A(1)E045 55 10 45 1.7 0.5
330.0 C T520C337M2R5A(1)E025 83 8 25 2.1 0.7
330.0 C T520C337M2R5A(1)E045 83 8 45 1.6 0.5
330.0 V T520V337M2R5A(1)E009 83 10 9 3.7 1.2
330.0 V T520V337M2R5A(1)E015 83 10 15 2.9 0.9
330.0 V T520V337M2R5A(1)E025 83 10 25 2.2 0.7
470.0 V T520V477M2R5A(1)E009 118 10 9 3.7 1.2
470.0 V T520V477M2R5A(1)E012 118 10 12 3.2 1.0
470.0 V T520V477M2R5A(1)E015 118 10 15 2.9 0.9
470.0 D T520D477M2R5A(1)E009 118 10 9 4.1 1.3
680.0 D T520D687M2R5A(1)E010 170 10 10 3.9 1.2
680.0 D T520D687M2R5A(1)E015 170 10 15 3.2 1.0
680.0 D T520D687M2R5A(1)E040 170 10 40 1.9 0.6
680.0 Y T520Y687M2R5A(1)E015 170 10 15 3.3 1.0
680.0 Y T520Y687M2R5A(1)E025 170 10 25 2.5 0.8

Polymer Tantalum Surface Mount

1000.0 Y T520Y108M2R5A(1)E010 250 10 10 4.0 1.3
1000.0 Y T520Y108M2R5A(1)E015 250 10 15 3.3 1.0
1000.0 Y T520Y108M2R5A(1)E025 250 10 25 2.5 0.8
1000.0 X T520X108M2R5A(1)E010 250 10 10 4.1 1.3
3 Volt Rating @ 105°C
100.0 B T520B107M003A(1)E040 30 8 40 1.5 0.5
100.0 B T520B107M003A(1)E070 30 8 70 1.1 0.3
150.0 B T520B157M003A(1)E040 45 8 40 1.5 0.5
150.0 B T520B157M003A(1)E070 45 8 70 1.1 0.3
330.0 V T520V337M003A(1)E009 99 10 9 3.7 1.2
330.0 V T520V337M003A(1)E012 99 10 12 3.2 1.0
330.0 V T520V337M003A(1)E015 99 10 15 2.9 0.9
330.0 V T520V337M003A(1)E025 99 10 25 2.2 0.7
680.0 D T520D687M003A(1)E015 204 10 15 3.2 1.0
680.0 D T520D687M003A(1)E040 204 10 40 1.9 0.6
1000.0 X T520X108M003A(1)E015 300 10 15 3.3 1.0
1000.0 X T520X108M003A(1)E030 300 10 30 2.3 0.7
4 Volt Rating @ 105°C
15.0 T T520T156M004A(1)E100 6 8 100 0.8 0.3
33.0 A T520A336M004A(1)E080 13 8 80 1.0 0.3
47.0 A T520A476M004A(1)E080 19 8 80 1.0 0.3
47.0 T T520T476M004A(1)E070 19 8 70 1.0 0.3
68.0 T T520T686M004A(1)E070 27 8 70 1.0 0.3
68.0 B T520B686M004A(1)E040 27 8 40 1.5 0.5
68.0 B T520B686M004A(1)E070 27 8 70 1.1 0.3
100.0 B T520B107M004A(1)E035 40 8 35 1.6 0.5
100.0 B T520B107M004A(1)E040 40 8 40 1.5 0.5
100.0 B T520B107M004A(1)E070 40 8 70 1.1 0.3
150.0 B T520B157M004A(1)E035 60 8 35 1.6 0.5
150.0 B T520B157M004A(1)E040 60 8 40 1.5 0.5
150.0 B T520B157M004A(1)E070 60 8 70 1.1 0.3
150.0 V T520V157M004A(1)E009 60 10 9 3.7 1.2
150.0 V T520V157M004A(1)E012 60 10 12 3.2 1.0
150.0 V T520V157M004A(1)E015 60 10 15 2.9 0.9
150.0 V T520V157M004A(1)E025 60 10 25 2.2 0.7
220.0 C T520C227M004A(1)E025 88 8 25 2.1 0.7
220.0 C T520C227M004A(1)E045 88 8 45 1.6 0.5
220.0 V T520V227M004A(1)E009 88 10 9 3.7 1.2
220.0 V T520V227M004A(1)E012 88 10 12 3.2 1.0
220.0 V T520V227M004A(1)E015 88 10 15 2.9 0.9
220.0 V T520V227M004A(1)E025 88 10 25 2.2 0.7
220.0 V T520V227M004A(1)E040 88 10 40 1.8 0.6
220.0 V T520V227M004A(1)E045 88 10 45 1.7 0.5
220.0 D T520D227M004A(1)E065 88 10 65 1.5 0.5
330.0 V T520V337M004A(1)E009 132 10 9 3.7 1.2
330.0 V T520V337M004A(1)E012 132 10 12 3.2 1.0
330.0 V T520V337M004A(1)E025 132 10 25 2.2 0.7
330.0 V T520V337M004A(1)E040 132 10 40 1.8 0.6
330.0 D T520D337M004A(1)E009 132 10 9 4.1 1.3
330.0 D T520D337M004A(1)E015 132 10 15 3.2 1.0
330.0 D T520D337M004A(1)E040 132 10 40 1.9 0.6
330.0 D T520D337M004A(1)E045 132 10 45 1.8 0.6
470.0 D T520D477M004A(1)E010 188 10 10 3.9 1.2
470.0 D T520D477M004A(1)E012 188 10 12 3.5 1.1
470.0 D T520D477M004A(1)E015 188 10 15 3.2 1.0
470.0 D T520D477M004A(1)E018 188 10 18 2.9 0.9
470.0 D T520D477M004A(1)E025 188 10 25 2.4 0.8
470.0 D T520D477M004A(1)E040 188 10 40 1.9 0.6
680.0 D T520D687M004A(1)E025 272 10 25 2.4 0.8
680.0 Y T520Y687M004A(1)E010 272 10 10 4.0 1.3
680.0 Y T520Y687M004A(1)E015 272 10 15 3.3 1.0
680.0 Y T520Y687M004A(1)E025 272 10 25 2.5 0.8
680.0 X T520X687m004A(1)E010 272 10 10 4.1 1.3
680.0 X T520X687M004A(1)E015 272 10 15 3.3 1.0
680.0 X T520X687M004A(1)E035 272 10 35 2.2 0.7

(1) To complete the KEMET part number, insert the lead material designator as shown on page 46.
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 47
 POLYMER TANTALUM CHIP CAPACITORS
T520 Series - KO Cap

T520 RATINGS & PART NUMBER REFERENCE

Ripple Current
DF% @ Arms @
DC Leakage ESR mΩ @
Capaci- Case 25°C 120 100 kHz Max
KEMET Part Number µA @ 25°C 25°C 100 kHz
tance µF Size Hz
Max Max w/∆T= 20°C
Max w/∆T= 2°C
@ -55°C to
@ 105°C
85°C
6.3 Volt Rating @ 105°C
15.0 T T520T156M006A(1)E100 9.5 8 100 0.8 0.3
22.0 A T520A226M006A(1)E100 14 8 100 0.9 0.3
33.0 A T520A336M006A(1)E080 21 8 80 1.0 0.3
33.0 B T520B336M006A(1)E040 21 8 40 1.5 0.5
33.0 B T520B336M006A(1)E070 21 8 70 1.1 0.3
47.0 T T520T476M006A(1)E070 30 8 70 1.0 0.3
47.0 B T520B476M006A(1)E040 30 8 40 1.5 0.5
47.0 B T520B476M006A(1)E070 30 8 70 1.1 0.3
68.0 B T520B686M006A(1)E040 43 8 40 1.5 0.5
68.0 B T520B686M006A(1)E070 43 8 70 1.1 0.3
100.0 B T520B107M006A(1)E040 63 8 40 1.5 0.5
100.0 B T520B107M006A(1)E070 63 8 70 1.1 0.3
100.0 V T520V107M006A(1)E009 63 10 9 3.7 1.2
100.0 V T520V107M006A(1)E012 63 10 12 3.2 1.0
150.0 C T520C157M006A(1)E025 95 8 25 2.1 0.7
150.0 C T520C157M006A(1)E045 95 8 45 1.6 0.5
150.0 W T520W157M006A(1)E040 95 10 40 1.7 0.5
150.0 V T520V157M006A(1)E009 95 10 9 3.7 1.2
150.0 V T520V157M006A(1)E012 95 10 12 3.2 1.0
150.0 V T520V157M006A(1)E015 95 10 15 2.9 0.9
150.0 V T520V157M006A(1)E025 95 10 25 2.2 0.7
150.0 V T520V157M006A(1)E040 95 10 40 1.8 0.6
150.0 V T520V157M006A(1)E045 95 10 45 1.7 0.5
150.0 D T520D157M006A(1)E015 95 10 15 3.2 1.0
150.0 D T520D157M006A(1)E025 95 10 25 2.4 0.8
150.0 D T520D157M006A(1)E055 95 10 55 1.7 0.5
220.0 V T520V227M006A(1)E009 139 10 9 3.7 1.2
220.0 V T520V227M006A(1)E012 139 10 12 3.2 1.0
220.0 V T520V227M006A(1)E015 139 10 15 2.9 0.9
220.0 V T520V227M006A(1)E025 139 10 25 2.2 0.7
220.0 V T520V227M006A(1)E040 139 10 40 1.8 0.6
220.0 D T520D227M006A(1)E009 139 10 9 4.1 1.3
220.0 D T520D227M006A(1)E015 139 10 15 3.2 1.0
220.0 D T520D227M006A(1)E040 139 10 40 1.9 0.6
220.0 D T520D227M006A(1)E050 139 10 50 1.7 0.5
330.0 V T520V337M006A(1)E025 208 10 25 2.2 0.7
330.0 V T520V337M006A(1)E040 208 10 40 1.8 0.6
330.0 D T520D337M006A(1)E010 208 10 10 3.9 1.2
330.0 D T520D337M006A(1)E015 208 10 15 3.2 1.0
330.0 D T520D337M006A(1)E025 208 10 25 2.4 0.8
330.0 D T520D337M006A(1)E040 208 10 40 1.9 0.6
330.0 D T520D337M006A(1)E045 208 10 45 1.8 0.6
330.0 Y T520Y337M006A(1)E015 208 10 15 3.3 1.0
330.0 Y T520Y337M006A(1)E025 208 10 25 2.5 0.8
470.0 Y T520Y477M006A(1)E010 296 10 10 4.0 1.3
470.0 Y T520Y477M006A(1)E015 296 10 15 3.3 1.0
470.0 Y T520Y477M006A(1)E018 296 10 18 3.0 0.9
470.0 Y T520Y477M006A(1)E025 296 10 25 2.5 0.8
470.0 X T520X477M006A(1)E010 296 10 10 4.1 1.3
470.0 X T520X477M006A(1)E018 296 10 18 3.0 1.0
470.0 X T520X477M006A(1)E035 296 10 35 2.2 0.7
470.0 X T520X477M006A(1)E040 296 10 40 2.0 0.6
8 Volt Rating @ 105°C
33.0 B T520B336M008A(1)E040 26 8 40 1.5 0.5
33.0 B T520B336M008A(1)E070 26 8 70 1.1 0.3
150.0 D T520D157M008A(1)E025 120 10 25 2.4 0.8
150.0 D T520D157M008A(1)E040 120 10 40 1.9 0.6
150.0 D T520D157M008A(1)E055 120 10 55 1.7 0.5
10 Volt Rating @ 105°C
33.0 B T520B336M010A(1)E040 33 8 40 1.5 0.5
33.0 B T520B336M010A(1)E070 33 8 70 1.1 0.3
68.0 V T520V686M010A(1)E045 68 10 45 1.7 0.5
68.0 V T520V686M010A(1)E060 68 10 60 1.4 0.5
100.0 V T520V107M010A(1)E018 100 10 18 2.6 0.8
100.0 V T520V107M010A(1)E025 100 10 25 2.2 0.7
100.0 V T520V107M010A(1)E045 100 10 45 1.7 0.5
100.0 V T520V107M010A(1)E050 100 10 50 1.6 0.5
100.0 D T520D107M010A(1)E018 100 10 18 2.9 0.9
100.0 D T520D107M010A(1)E055 100 10 55 1.7 0.5
100.0 D T520D107M010A(1)E080 100 10 80 1.4 0.4
150.0 D T520D157M010A(1)E025 150 10 25 2.4 0.8
150.0 D T520D157M010A(1)E040 150 10 40 1.9 0.6
150.0 D T520D157M010A(1)E055 150 10 55 1.7 0.5
220.0 D T520D227M010A(1)E018 220 10 18 2.9 0.9
220.0 D T520D227M010A(1)E025 220 10 25 2.4 0.8
220.0 D T520D227M010A(1)E040 220 10 40 1.9 0.6
330.0 Y T520Y337M010A(1)015 330 10 15 3.3 1.0
330.0 X T520X337M010A(1)E025 330 10 25 2.6 0.8
330.0 X T520X337M010A(1)E040 330 10 40 2.0 0.6
16 Volt Rating @ 105°C
33.0 V T520V336M016A(1)E060 53 10 60 1.4 0.5
47.0 V T520V476M016A(1)E070 76 10 70 1.3 0.4
47.0 D T520D476M016A(1)E035 75 10 35 2.1 0.7
47.0 D T520D476M016A(1)E070 75 10 70 1.5 0.5
20 Volt Rating @ 105°C
22.0 V T520V226M020A(1)E090 44 10 90 1.2 0.4
25 Volt Rating @ 105°C
15.0 V T520V156M025A(1)E090 38 10 90 1.2 0.4
15.0 D T520D156M025A(1)E060 38 10 60 1.6 0.5
15.0 D T520D156M025A(1)E080 38 10 80 1.4 0.4

(1) To complete the KEMET part number, insert the lead material designator as shown on page 46.

48 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 POLYMER TANTALUM CHIP CAPACITORS
T525 SERIES - High Temperature

FEATURES
• Polymer Cathode Technology • Operating Temperature -55ºC to +125ºC
• 125ºC Maximum Temperature Capability • 100% Accelerated Steady State Aging
• High Frequency Capacitance Retention • 100% Surge Current Testing
• Non-Ignition Failure Mode • Self-Healing Mechanism
• Capacitance: 33 - 680µF • Volumetrically Efficient
• Voltage: 2.5 to 16 volts • Extremely Stable ESR at 125ºC
• Halogen Free Epoxy • EIA Standard Case Size
• Use up to 90% of Rated Voltage (10% Derating) • RoHS Compliant / Leadfree Termination
for part types ≤ 10 Volts (See www.kemet.com for lead transition)
• Use up to 80% of Rated Voltage (20% Derating) for part
types >10 Volts

OUTLINE DRAWING
CATHODE (-) END SIDE VIEW ANODE (+) END BOTTOM VIEW
VIEW VIEW

H E F
K T

A
X S G S
L

Polymer Tantalum Surface Mount

DIMENSIONS - MILLIMETERS
Case Size
KEMET EIA L W H K ±0.20 F ±0.1 S ±0.3 X(Ref) T(Ref) A(Min) G(ref) E(ref)

B 3528-21 3.5 ± 0.2 2.8 ± 0.2 1.9 ± 0.1 0.9 2.2 0.8 0.10 ± 0.10 0.13 1.1 1.8 2.2
D 7343-31 7.3 ± 0.3 4.3 ± 0.3 2.8 ± 0.3 1.5 2.4 1.3 0.10 ± 0.10 0.13 3.8 3.5 3.5

RECOMMENDED TEMPERATURE/VOLTAGE
Ω Ω
DERATING
100%
100% 100% 100% 100% Ω
T525 Rated Voltage
90%
90% 90% 90% 90% T525 Recommended
Application Voltage
% Rated Voltage

80% (Vr<10VDC)
80% 80% 80% 80%
T525 Recommended
Application Voltage
70% (Vr>10VDC)
67%

60% 60%

53%
50%
-55 25 85 105 125
Temperature (°C)
COMPONENT MARKING
KEMET High Temperature
Tantalum Polymer (KT) KT Polarity
Indicator (+)
(Solid Stripe)

477 Picofarad
Code
Rated
Voltage 4K KEMET
I. D. Symbol

1st Digit
=Year
414 2nd & 3rd Digits
= Week
“414” = The 14th week of 2004
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 49
 POLYMER TANTALUM CHIP CAPACITORS
T525 SERIES - High Temperature

T525 RATINGS & PART NUMBER REFERENCE

Ripple Current
DC DF% ESR mΩ (Arms)
Capaci- Case Leakage @ 25°C @ 25°C 100 kHz Max
KEMET Part Number
tance µF Size µA @ 25°C 120 Hz 100 kHz
w/∆T= 20°C
Max Max Max @ -55°C to
w/∆T= 2°C
@ 125°C
105°C

2.5 Volt Rating at 105°C (1.7 Volt Rating at 125°C)

100.0 T T525T107M2R5A(1)E080 25 8.0 80 0.9 0.3
330.0 D T525D337M2R5A(1)E025 83 10.0 25 2.4 0.8
470.0 D T525D477M2R5A(1)E025 118 10.0 25 2.4 0.8
680.0 D T525D687M2R5A(1)E025 170 10.0 25 2.4 0.8
3 Volt Rating at 105°C (2 Volt Rating at 125°C)
100.0 B T525B107M003A(1)E080 30 8.0 80 1.0 0.3
150.0 B T525B157M003A(1)E080 45 8.0 80 1.0 0.3
330.0 D T525D337M003A(1)E025 99 10.0 25 2.4 0.8
470.0 D T525D477M003A(1)E025 141 10.0 25 2.4 0.8
680.0 D T525D687M003A(1)E025 204 10.0 25 2.4 0.8
4 Volt Rating at 105°C (2.7 Volt Rating at 125°C)
68.0 T T525T686M004A(1)E080 27 8.0 80 0.9 0.3
68.0 B T525B686M004A(1)E080 28 8.0 80 1.0 0.3
100.0 B T525B107M004A(1)E080 40 8.0 80 1.0 0.3
220.0 D T525D227M004A(1)E025 88 10.0 25 2.4 0.8
330.0 D T525D337M004A(1)E025 132 10.0 25 2.4 0.8
470.0 D T525D477M004A(1)E025 188 10.0 25 2.4 0.8
470.0 D T525D477M004A(1)E040 188 10.0 40 1.9 0.6
6.3 Volt Rating at 105°C (4.2 Volt Rating at 125°C)
33.0 B T525B336M006A(1)E080 21 8.0 80 1.0 0.3
47.0 T T525T476M006A(1)E080 30 8.0 80 0.9 0.3
47.0 B T525B476M006A(1)E080 30 8.0 80 1.0 0.3
68.0 B T525B686M006A(1)E080 43 8.0 80 1.0 0.3
150.0 D T525D157M006A(1)E025 95 10.0 25 2.4 0.8
220.0 D T525D227M006A(1)E025 139 10.0 25 2.4 0.8
330.0 D T525D337M006A(1)E025 208 10.0 25 2.4 0.8
330.0 D T525D337M006A(1)E040 208 10.0 40 1.9 0.6
10 Volt Rating at 105°C (6.6 Volt Rating at 125°C)
22.0 B T525B226M010A(1)E080 22 8.0 80 1.0 0.3
33.0 T T525T336M006A(1)E080 33 8.0 80 0.9 0.3
33.0 B T525B336M010A(1)E080 33 8.0 80 1.0 0.3
100.0 D T525D107M010A(1)E025 100 10.0 25 2.4 0.8
100.0 D T525D107M010A(1)E055 100 10.0 55 1.7 0.5
150.0 D T525D157M010A(1)E025 150 10.0 25 2.4 0.8
150.0 D T525D157M010A(1)E055 150 10.0 55 1.7 0.5
220.0 D T525D227M010A(1)E025 220 10.0 25 2.4 0.8
16 Volt Rating at 105°C (10.6 Volt Rating at 125°C)
47.0 D T525D476M016A(1)E035 76 10.0 35 2.1 0.7
47.0 D T525D476M016A(1)E065 76 10.0 65 1.5 0.5
(1) To complete the KEMET part number, insert the lead material designator as shown below.

T525 ORDERING INFORMATION

T 525 D 337 M 006 A T E040
Tantalum ESR
Series
T525 - High Temperature Lead Material
Tantalum Polymer (KT) T - 100% Tin (Sn)
Case Size Failure Rate
D B, D
T, A - Not Applicable
Capacitance Picofarad Code Voltage
First two digits represent significant figures. Note: 006 - 6.3
Third digit specifies number of zeros to follow.
Capacitance Tolerance
M = ± 20%

50 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 POLYMER TANTALUM CHIP CAPACITORS
T530 SERIES - Multiple Anode
FEATURES
• Highest CV in Standard EIA Size • 100% Surge Current Testing
• Extremely Low ESR • Utilizes Multiple Tantalum Anode Technology
• 125C Max, Temperature Capability • Volumetric Efficiency
• Polymer Cathode Technology • Use Up to 90% of Rated Voltage (10% Derating)
• High Frequency Capacitance Retention • Self-Healing Mechanism
• Non-Ignition Failure Mode • True SMT Capability
• Capacitance: 220 to 1500 F
• Voltage: 2.5V to 10V
• Molded Case (pick-and-place precision)
• 100% Accelerated Steady State Aging

OUTLINE DRAWINGS
CATHODE (-) END SIDE VIEW ANODE (+) END BOTTOM VIEW
VIEW VIEW
B
W
B

H E F
K T

A
X S G S
L

DIMENSIONS - MILLIMETERS (INCHES)

Case Size
KEMET EIA L W H K ±0.20 F ±0.1 S ±0.3 X(Ref) T(Ref) A(Min) G(ref) E(ref)
D 7343-31 7.3 ± 0.3 4.3 ± 0.3 2.8 ± 0.3 1.5 2.4 1.3 0.10 ± 0.10 0.13 3.8 3.5 3.5
Y 7343-40 7.3 ± 0.3 4.3 ± 0.3 4.0 max 1.9 2.4 1.3 0.10 ± 0.10 0.13 3.8 3.5 3.5
X 7343-43 7.3 ± 0.3 4.3 ± 0.3 4.0 ± 0.3 2.3 2.4 1.3 0.10 ± 0.10 0.13 3.8 3.5 3.5

T530 SERIES RATINGS & PART NUMBER REFERENCE

ESR Ripple Current
Capaci- DCL DF % mΩ @100 (Arms) @ 100 kHz
Case Size KEMET Part Number
tance µF VR 120Hz kHz 25°C w/∆T= 20°C
w/∆T= 2°C
@ -55°C to
Max 105°C
@ 125°C

2.5 Volt Rating at 105°C (1.7 Volt Rating at 125°C)

470.0 D/7343-31 T530D477M2R5A(1)E005 118µA 8.0 5.0 7.1 2.3
470.0 D/7343-31 T530D477M2R5A(1)E006 118µA 8.0 6.0 6.5 2.1
470.0 D/7343-31 T530D477M2R5A(1)E010 118µA 10.0 10.0 5.0 1.6
560.0 D/7343-31 T530D567M2R5A(1)E005 140µA 8.0 5.0 7.1 2.3
680.0 Y/7343-40 T530Y687M2R5A(1)E005 170µA 8.0 5.0 7.2 2.3
680.0 Y/7343-40 T530Y687M2R5A(1)E006 170µA 8.0 6.0 6.6 2.1
680.0 D/7343-31 T530D687M2R5A(1)E006 170µA 8.0 6.0 6.5 2.1
680.0 D/7343-31 T530D687M2R5A(1)E010 170µA 8.0 10.0 5.0 1.6
1000.0 X/7343-43 T530X108M2R5A(1)E005 250µA 8.0 5.0 7.3 2.3
1000.0 X/7343-43 T530X108M2R5A(1)E006 250µA 8.0 6.0 6.7 2.1
1500.0 X/7343-43 T530X158M2R5A(1)E005 375µA 8.0 5.0 7.3 2.3
3 Volt Rating at 105°C (2 Volt Rating at 125°C)
470.0 D/7343-31 T530D477M003A(1)E010 141µA 8.0 10.0 5.0 1.6
680.0 D/7343-31 T530D687M003A(1)E010 204µA 8.0 10.0 5.0 1.6
1000.0 X/7343-43 T530X108M003A(1)E010 300µA 8.0 10.0 5.2 1.6
1500.0 X/7343-43 T530X158M003A(1)E008 450µA 8.0 8.0 5.8 1.8
4 Volt Rating at 105°C (2.7 Volt Rating at 125°C)
330.0 D/7343-31 T530D337M004A(1)E005 132µA 8.0 5.0 7.1 2.3
330.0 D/7343-31 T530D337M004A(1)E006 132µA 8.0 6.0 6.5 2.1
470.0 D/7343-31 T530D477M004A(1)E010 188µA 8.0 10.0 5.0 1.6
470.0 Y/7343-40 T530Y477M004A(1)E005 188µA 8.0 5.0 7.2 2.3
470.0 Y/7343-40 T530Y477M004A(1)E006 188µA 8.0 6.0 6.6 2.1
680.0 X/7343-43 T530X687M004A(1)E005 272µA 8.0 5.0 7.3 2.3
680.0 X/7343-43 T530X687M004A(1)E006 272µA 8.0 6.0 6.7 2.1
680.0 X/7343-43 T530X687M004A(1)E010 272µA 8.0 10.0 5.2 1.6
1000.0 X/7343-43 T530X108M004A(1)E006 400µA 8.0 6.0 6.7 2.1
6.3 Volt Rating at 105°C (4.2 Volt Rating at 125°C)
220.0 D/7343-31 T530D227M006A(1)E005 139µA 8.0 5.0 7.1 2.3
220.0 D/7343-31 T530D227M006A(1)E006 139µA 8.0 6.0 6.5 2.1
330.0 Y/7343-40 T530Y337M006A(1)E005 208µA 8.0 5.0 7.2 2.3
330.0 Y/7343-40 T530Y337M006A(1)E006 208µA 8.0 6.0 6.6 2.1
330.0 Y/7343-40 T530Y337M006A(1)E010 208µA 8.0 10.0 5.1 1.6
330.0 D/7343-31 T530D337M006A(1)E010 208µA 8.0 10.0 5.0 1.6
470.0 X/7343-43 T530X477M006A(1)E005 296µA 8.0 5.0 7.3 2.3
470.0 X/7343-43 T530X477M006A(1)E006 296µA 8.0 6.0 6.7 2.1
470.0 X/7343-43 T530X477M006A(1)E010 296µA 8.0 10.0 5.2 1.6
10 Volt Rating at 105°C (6.6 Volt Rating at 125°C)
150.0 D/7343/31 T530D157M010A(1)E005 150µA 8.0 5.0 7.1 2.3
150.0 D/7343/31 T530D157M010A(1)E006 150µA 8.0 6.0 6.5 2.1
220.0 D/7343/31 T530D227M010A(1)E010 220µA 8.0 10.0 5.0 1.6
330.0 X/7343-43 T530X337M010A(1)E005 330µA 8.0 5.0 7.3 2.3
330.0 X/7343-43 T530X337M010A(1)E006 330µA 8.0 6.0 6.7 2.1
330.0 X/7343-43 T530X337M010A(1)E010 330µA 8.0 10.0 5.2 1.6
(1) To complete the KEMET part number, insert the lead material designator as shown on page 52.
51
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 POLYMER TANTALUM CHIP CAPACITORS
T530 SERIES - Multiple Anode

T530 ORDERING INFORMATION

T 530 X 158 M 003 A S E008
Tantalum ESR
Lead Material
Series *S - 100% Tin (Sn) Plated
T530 - Multiple Anode H - Standard Solder Coated
Polymer Tantalum T - 100% Tin
G - Gold
Case Size Failure Rate
D, X, Y A - Not Applicable
Capacitance Picofarad Code Voltage
Note: 006 = 6.3
Capacitance Tolerance
M - ± 20%
*Refer to www.kemet.com for Pb Free transition information
COMPONENT MARKING T530 SERIES CONSTRUCTION

(KM) KEMET
Polarity
Multi Polymer
Anode
KM Indicator

158 Picofarad Co
Rated
Voltage 3K KEMET ID

405 PWC*

“405” = The 5th week

of 2004.

T530X/T510E/T491E 1,000µF T530X/T510E/T491E 1,000µF

Capacitance vs. Frequency Impedance & ESR vs. Frequency
100 kHz
1000 100 kHz
10
900
800
Z & ESR (Ohms)

T510E
Capacitance

700 1 T491E
600 T491E T530X
500 0.1
400
T510E
300
200 0.01
100
T530X
0 0.001
1.E+02 1.E+03 1.E+04 1.E+05 1.E+06 1.E+07 1.E+02 1.E+03 1.E+04 1.E+05 1.E+06 1.E+07 1.E+08
Frequency (Hz ) Frequency (Hz )

RECOMMENDED TEMPERATURE/VOLTAGE DERATING

52 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 CERAMIC CHIP CAPACITORS

INTRODUCTION Table 1 – EIA Temperature Characteristic

Codes for Class I Dielectrics
Ceramic chips consist of formulated ceramic Significant Figure
of Temperature
Multiplier Applied
to Temperature
Tolerance of
Temperature
Coefficient Coefficient Coefficient
dielectric materials which have been fabricated into thin
PPM per Letter Multi- Number PPM per Letter
layers, interspersed with metal electrodes alternately Degree C Symbol plier Symbol Degree C Symbol
exposed on opposite edges of the laminated structure. 0.0 C -1 0 ± 30 G
0.3 B -10 1 ± 60 H
The entire structure is then fired at high temperature to 0.9 A -100 2 ± 120 J
1.0 M -1000 3 ± 250 K
produce a monolithic block which provides high capaci- 1.5 P -10000 4 ± 500 L
KEMET supplies the C0G characteristic.
tance values in a small physical volume. After firing, con-
ductive terminations are applied to opposite ends of the For Class II and III dielectrics (including X7R,
chip to make contact with the exposed electrodes. X5R, Z5U & Y5V), the first symbol indicates the
Standard end terminations use a nickel barrier layer and lower limit of the operating temperature range, the
a tin overplate to provide excellent solderability for the second indicates the upper limit of the operating
customer. temperature range, and the third indicates the
KEMET multilayer ceramic chip capacitors are maximum capacitance change allowed over the
produced in plants designed specifically for chip capa- operating temperature range. EIA type designa-
citor manufacture. The process features a high degree tion codes for Class II and III dielectrics are
of mechanization as well as precise controls over raw shown in Table 2.
materials and process conditions. Manufacturing is
supplemented by extensive Technology, Engineering
Table 2 – EIA Temperature Characteristic Codes for
and Quality Assurance programs. Class II & III Dielectrics
KEMET ceramic chip capacitors are offered in the Low Temperature
Rating
High Temperature
Rating
Maximum Capacitance
Shift
five most popular temperature characteristics. These Degree Letter Degree Number Letter EIA
are designated by the Electronics Industies Association Celsius Symbol Celsius Symbol Percent Symbol Class

(EIA) as the ultra-stable C0G (also known as NP0, +10C Z +45C 2 ± 1.0% A II
-30C Y +65C 4 ± 1.5% B II
military version BP), the stable X7R (military BX or -55C X +85C 5 ± 2.2% C II
+105C 6 ± 3.3% D II
BR), the stable X5R, and the general purpose Z5U and +125C 7 ± 4.7% E II
+150C 8 ± 7.5% F II
Y5V. A wide range of sizes are available. KEMET multi- +200C 9 ± 10.0% P II
± 15.0% R II
layer ceramic chip capacitors are available in KEMET's ± 22.0% S III
+ 22/-33% T III
tape and reel packaging, compatible with automatic +22/-56% U III
+22/-82% V III
placement equipment. Bulk cassette packaging is also
KEMET supplies the X7R, X5R, Z5U and Y5V characteristics.
available (0805,0603 and 0402 only) for those pick and
place machines requiring its use. 3. Capacitance Tolerance:
ELECTRICAL CHARACTERISTICS See tables on pages 59-62.
4. Capacitance:
1. Working Voltage: Within specified tolerance when measured per

Ceramic Surface Mount

Refers to the maximum continuous DC working Table 3.
voltage permissible across the entire operating The standard unit of capacitance is the farad.
temperature range. The reliability of multilayer For practical capacitors, capacitance is usually
ceramic capacitors is not extremely sensitive to expressed in microfarads (10 -6 farad), nanofarads
voltage, and brief applications of voltage above (10 -9 farad), or picofarads (10 -12 farad). Standard
rated will not result in immediate failure. However, measurement conditions are listed in Table 3 -
reliability will be degraded by sustained exposure Specified Electrical Limits.
to voltages above rated. Like all other practical capacitors, multilayer
2. Temperature Characteristics: ceramic capacitors also have resistance and
Within the EIA classifications, various tempera- inductance. A simplified schematic for the single
ture characteristics are identified by a three-symbol frequency equivalent circuit is shown in Figure 1.
code; for example: C0G, X7R, X5R, Z5U and Y5V. At high frequency more complex models apply -
For Class I temperature compensating see KEMET SPICE models at www.kemet.com for
dielectrics (includes C0G), the first symbol desig- details.
nates the significant figures of the temperature
coefficient in PPM per degree Celsius, the second
designates the multiplier to be applied, and the
third designates the tolerance in PPM per
degrees Celsius. EIA temperature characteristic
codes for Class I dielectrics are shown in Table 1.

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 53
 CERAMIC CHIP CAPACITORS

Figure 1 IR 6. Impedance:
Since the parallel resistance (IR) is normally very
high, the total impedance of the capacitor can be
approximated by:
ESL ESR
Figure 3
C
2 2
C = Capacitance ESR = Equivalent Series Resistance ESR + (X - X )
Z= L C
ESL = Equivalent Series Inductance IR = Insulation Resistance

Where : Z = Total Impedance

5. Dissipation Factor:
ESR = Equivalent Series Resistance
Measured under same conditions as
capacitance. (See Table 3) X = Capacitive Reactance = 1/(2 πfC)
Dissipation factor (DF) is a measure of the losses in C
a capacitor under AC application. It is the ratio of the X = Inductive Reactance = (2 πf) (ESL)
L
equivalent series resistance to the capacitive reac- The variation of a capacitor's impedance with fre-
tance, and is usually expressed in percent. It is normal- quency determines its effectiveness in many applica-
ly measured simultaneously with capacitance, and tions. At high frequency more detailed models apply -
under the same conditions. The vector diagram below see KEMET SPICE models for such instances.
illustrates the relationship between DF, ESR and
7. Insulation Resistance:
impedance. The reciprocal of the dissipation factor is
Measured after 2 minutes electrification at 25°C and
called the “Q” or quality factor. For convenience, the
rated voltage: Limits per Table 3.
“Q” factor is often used for very low values of dissipa-
Insulation Resistance is the measure of a capacitor
tion factor especially when measured at high frequen-
to resist the flow of DC leakage current. It is sometimes
cies. DF is sometimes called the “loss tangent” or “tan-
referred to as “leakage resistance”. Insulation resis-
gent ”, as shown in Figure 2.
tance (IR) is the DC resistance measured across the
terminals of a capacitor, represented by the parallel
ESR
Figure 2 resistance (IR) shown in Figure 1. For a given dielectric
O type, electrode area increases with capacitance, result-
DF(%) = ESR x 100 ing in a decrease in the insulation resistance.
Xc
δ Consequently, insulation resistance limits are usually
specified as the “RC” (IR x C) product, in terms of ohm-
X
c Ζ farads or megohm-micro-farads. The insulation resis-
tance for a specific capacitance value is determined by
1 dividing this product by the capacitance. However, as
Xc =
2 π fC the nominal capacitance values become small, the
insulation resistance calculated from the RC product
reaches values which are impractical. Consequently, IR
specifications usually include both a minimum RC prod-
uct and a maximum limit based on the IR calculated

Table 3 – Specified Electrical Limits

Temperature Characteristics
Parameter
C0G X7R/X5R Z5U Y5V
Capacitance & Dissipation Factor: Measured at following
conditions:
C0G – 1kHz and 1 vrms if capacitance >1000 pF
1MHz and 1 vrms if capacitance ≤1000 pF
X7R/X5R/Y5V – 1kHz and 1 vrms* if capacitance ≤ 10 µF
X7R/X5R/Y5V – 120Hz and 0.5 vrms if capacitance > 10 µF
Z5U – 1kHz and 0.5 vrms
DF Limits: **X5R Cap DF 50 - 200 volts – 0.10% 2.5% 2.5% 4.0% 5.0%
25 volts – 0.10% 3.5% 5.0% 4.0% 7.0%
<25V <564 5.0%
16 volts – -------- 3.5% ** ------- 7.0%
<25V ≥564 8.0% 6.3/10 volts – -------- 5.0% 10.0%
**

Dielectric Strength: At 2.5 times rated DC voltage Pass Subsequent IR Test

1,000 MΩ – µF 1,000 MΩ – µF 100 MΩ – µF 100 MΩ – µF
Insulation Resistance (IR): At rated DC voltage, whichever or 100 GΩ or 100 GΩ or 10 GΩ or 10 G (≥16 volt)
of the two is smaller. To get IR limit, divide MΩ−µF value by (100,000 MΩ) (100,000 MΩ) (10,000 MΩ) 50 MΩ – µF
the capacitance and compare to GΩ limit. Select the lower or 10G (≤10v)
of the two limits. (10,000 MΩ)
Temperature: Range, °C -55 to +125 X7R: -55 to +125 ± 15% +10 to +85 -30 to +85
Capacitance Change (without DC voltage) 0 ± 30 ppm/°C X5R: -55 to +85 ± 15% +22% -56% +22% -82%

*Note: Some values measured at 1⁄2 volt, see X7R Table for specific details on pages 60 and 61.

54 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 CERAMIC CHIP CAPACITORS
from that value. For example, a typical IR specification However, this only defines an “envelope” bounded
might read “1,000 megohm-microfarads or 100 by the upper and lower operating temperatures and the
gigohms, whichever is less”. The DC leakage current minimum and maximum capacitance values. Within this
may be calculated by dividing the applied voltage by “envelope”, the variation with temperature depends
the insulation resistance (Ohm's Law). upon the specific dielectric formulation.
Insulation resistance decreases with increasing tem-
8. Dielectric Withstanding Voltage:
250% of rated voltage for 5 seconds with current lim- perature. Typically, the insulation resistance limit at
ited to 50mA at 25°C. Limits per Table 3. maximum rated temperature is 10% of the 25°C value.
Dielectric withstanding voltage (DWV) is the peak DC 11. Effect of Voltage:
voltage which a capacitor is designed to withstand with- Certain high dielectric constant ceramic capacitors
out damage for short periods of time. All KEMET multi- may show variation in values of capacitance and dissi-
layer ceramic surface mount capacitors will withstand a pation factor with various levels of applied AC and DC
DC test voltage of 2.5 x the rated voltage for 60 sec- voltages. Such variation is a natural characteristic of
onds. ceramic capacitors, and should be considered by the
KEMET specification limits for all electrical character- circuit designer.
istics at standard measurement conditions are shown in In general, ceramic capacitors with the lowest dielec-
Table 3. Variations in these properties caused by tric constant (C0G or NP0) are extremely stable, and
changing conditions (temperature, voltage, frequency, show little or no variation in capacitance and/or dissipa-
and time) are covered in the following sections. tion factor. On the other hand, ceramic capacitors with
9. Aging Rate: the highest dielectric constant (Z5U & Y5V) may show
Maximum % Capacitance Loss/Decade Hour significant variation, particularly in capacitance. Other
C0G - 0% dielectric formulations such as X7R and X5R will show
X7R - 2.0% less variation than Y5V, but more than C0G.
X5R - 3.5% The application of AC voltages in the range of 10 to
Z5U - 7.0% 20 VAC tends to increase the values of both the capaci-
Y5V - 7.0% tance and dissipation factor, while higher AC voltages
Actual rates may be lower. Consult factory for
tend to produce decreases in both.
details.
However, the variation of capacitance with applied
The capacitance of Class II and III dielectric changes DC is the parameter of most interest to design engi-
with time as well as with temperature, voltage and fre- neers. Figure 8 shows typical variation of capacitance
quency. The change with time is known as “aging”. It is with applied DC voltage for some standard dielectrics.
caused by gradual realignment of the crystalline struc- As can be seen, the decrease in capacitance is greatest
ture of the ceramic dielectric material as it is cooled for the Y5V dielectric (the C0G is not plotted, since it
below its Curie temperature, which produces a loss of would not have a perceptible capacitance nor dissipa-
capacitance with time. The aging process is predictable tion factor change.)

Ceramic Surface Mount

and follows a logarithmic decay.
The aging process is reversible. If the capacitor is
heated to a temperature above its Curie point for some
period of time, de-aging will occur and the capacitor will
regain the capacitance lost during the aging process.
The amount of de-aging depends on both the elevated
temperature and the length of time at that temperature.
Exposure to 150°C for one-half hour is sufficient to
return the capacitor to its initial value.
Figure 8 - Typical Variation of Capacitance with Applied DC Voltage
Because the capacitance changes rapidly immedi-
ately after de-aging, capacitance measurements are More detailed modelling information on the effect of
usually delayed for at least 10 - 24 hours after the de- various voltages on specific capacitor ratings can be
aging process, which is often referred to as the “last obtained by use of the KEMET SPICE models, available
heat”. In addition, manufacturers utilize the aging rates for free downloading at our website (www.kemet.com).
to set factory test limits which will bring the capacitance 12. Effect of Frequency:
within the specified tolerance at some future time, to Frequency affects both capacitance and dissipation
allow for customer receipt and use. factor. Typical curves for KEMET multilayer ceramic
10. Effect of Temperature: capacitors are shown in Figures 4, 5, 6 and 7.
Both capacitance and dissipation factor are affected The variation of impedance with frequency is an
by variations in temperature. The maximum capacitance important consideration in the application of multilayer
change with temperature is defined by the temperature ceramic capacitors. Total impedance of the capacitor is
characteristic. the vector summation of the capacitive reactance, the
inductive reactance, and the ESR, as illustrated in
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 55
 CERAMIC CHIP CAPACITORS
Figure 2. As frequency increases, the capacitive reac- low, failure rate when operated within rated conditions.
tance decreases. However, the series inductance (L) The primary failure mode is by short-circuit or low insu-
shown in Figure 1 produces some inductive reactance, lation resistance, resulting from cracks or from dielectric
which increases with frequency. At some frequency, the breakdown at a defect site. KEMET monitors reliability
impedance ceases to be capacitive and becomes with a periodic sampling program for selected values.
Results are available in our FIT (Failure in Time) report
inductive. This point, at the bottom of the V-shaped
for commercial chips.
impedance versus frequency curves, is the self-reso-
nant frequency. At the self-resonant frequency, the 21. Storage and Handling:
reactance is zero, and the impedance consists of the Ceramic chip capacitors should be stored in normal
ESR only. At high frequency more detailed models working environments. While the chips themselves are
apply - See KEMET SPICE models for such instances. quite robust in other environments, solderability will be
Typical impedance versus frequency curves for degraded by exposure to high temperatures, high
KEMET multilayer ceramic capacitors are shown in humidity, corrosive atmospheres, and long term stor-
Figures 4, 5, 6 and 7. age. In addition, packaging materials will be degraded
by high temperature – reels may soften or warp, and
ENVIRONMENTAL AND PHYSICAL tape peel force may increase. KEMET recommends
13. Thermal Shock: that maximum storage temperature not exceed 40
EIA-198, Method 202, Condition B (5 cycles degrees C, and maximum storage humidity not exceed
-55° to + 125°C). 70% relative humidity. In addition, temperature fluctua-
tions should be minimized to avoid condensation on
14. Life Test: the parts, and atmospheres should be free of chlorine
EIA-198, Method 201, 1000 hours at 200% of rated and sulfur bearing compounds. For optimized solder-
voltage at 125°C. (Except 85°C for Z5U and Y5V). ability, chip stock should be used promptly, preferably
See Table 4 on page 48 for limits.
within 1.5 years of receipt.
15. Humidity Test: MISAPPLICATION
EIA-198, Method 206, ( Except 1000 hours,85°C,
85% RH, Rated Voltage).
See Table 4 on page 48 for limits. 22. Ceramic capacitors, like any other capacitors, may fail if
they are misapplied. Some misapplications include
16. Moisture Resistance: mechanical damage, such as impact or excessive flex-
EIA-198, Method 204, Condition B (20 cycles with ing of the circuit board. Others include severe mounting
50 volts applied. or rework cycles that may also introduce thermal shock.
See Table 4 on page 48 for limits. Still others include exposure to excessive voltage, cur-
rent or temperature. If the dielectric layer of the capaci-
17. Solderability: tor is damaged by misapplication, the circuit may fail.
EIA-198, Method 301 (245°, 5 secs, Sn62 solder) The electrical energy of the circuit can be released as
95% smooth solder on terminations. See page 14 heat, which may damage the circuit board and other
for recommended profiles. components as well.

18. Resistance to Soldering Heat: ADDITIONAL INFORMATION

EIA-198, Method 302, Condition B (260°C, 10 sec-
onds) no leaching of nickel barrier. 23. Detailed application information can be found in KEMET
Engineering Bulletins.
19. Terminal Strength:
EIA-198, Method 303, Condition D . F-2100 Surface Mount-Mounting Pad
Dimensions and Considerations
RELIABILITY F-2102 Reflow Soldering Process
F-2105 Wave Solder Process
20. A well constructed multilayer ceramic capacitor chip is F-2103 Surface Mount Repair
extremely reliable and, for all practical purposes, has no F-2110 Capacitance Monitoring while Flex Testing
wearout mechanism when used within the maximum F-2111 Ceramic Chip Capacitors “Flex Cracks” -
voltage and temperature ratings. Most failures occur as Understanding and Solutions
a result of mechanical or thermal damage during
mounting on the board, or during subsequent testing. For analysis of high frequency applications, KEMET
Capacitor failure may also be induced by sustained has SPICE models of most chip capacitors. Models
operation at voltages that exceed the rated DC voltage, may be downloaded from KEMET’s website
voltage spikes or transients that exceed the dielectric's www.kemet.com.
voltage capability, sustained operation at temperatures Additional information is also available - See
above the maximum rated temperature, internal your KEMET representative for details or post your
defects, or excessive temperature rise due to power questions to KEMET's homepage on the web
dissipation. As with any practical device, multilayer http://www.kemet.com.
ceramic capacitors also possess an inherent, although

56 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 CERAMIC CHIP CAPACITORS

TABLE 4 – ENVIRONMENTAL LIMITS

Cap Shift (% or pf, IR (GΩ or ΩF)
IR DF (%) whichever is greater) whichever is less
(GΩ or ΩF) Post Life/ Post Life/ Post Life/
Rated DC Initial whichever is Hum/Moisture Hum/Moisture Hum/Moisture
Body Voltage DF (%) less Resistance Resistance Resistance
C0G 200 ∗ 0.1 100/1000 0.5 0.3% or ± 0.25 pf 10/100
100 0.1 100/1000 0.5 0.3% or ± 0.25 pf 10/100
50 0.1 100/1000 0.5 0.3% or ± 0.25 pf 10/100
25 0.1 100/1000 0.5 0.3% or ± 0.25 pf 10/100
16 0.1 100/1000 0.5 0.3% or ± 0.25 pf 10/100
X7R 200 ∗ 2.5 100/1000 3.0 ± 20% 10/100
100 2.5 100/1000 3.0 ± 20% 10/100
50 2.5 100/1000 3.0 ± 20% 10/100
25 3.5 100/1000 5.0 ± 20% 10/100
16 3.5 100/1000 5.0 ± 20% 10/100
6.3/10 5.0 100/1000 7.5 ± 20% 10/100
X5R 50V all cap values 2.5 100/1000 3.0 ± 20% 10/100
25V all cap values 3.5 100/1000 5.0 ± 20% 10/100
<25V≥564 cap value 5.0 100/1000 7.5 ± 20% 10/100
<564 cap value 8.0 100/1000 12.0 ± 20% 10/100
Z5U 100 4.0 10/100 5.0 ± 30% 1/10
50 4.0 10/100 5.0 ± 30% 1/10
25 4.0 10/100 7.5 ± 30% 1/10
Y5V 100 5.0 10/100 7.5 ± 30% 1/10
50 5.0 10/100 7.5 ± 30% 1/10
25 7.0 10/100 10.0 ± 30% 1/10
16 7.0 10/100 10.0 ± 30% 1/10
6.3/10 10.0 10/50 15.0 ± 30% 1/5
*200 Volt limits not currently included in EIA-198.

PERFORMANCE CURVES
EFFECT OF FREQUENCY
(See SPICE models for specific ratings.)

Impedance (Ohms) Impedance (Ohms)

100,000 1,000

10,000
100

Ceramic Surface Mount

1,000

100
10
10 0805
103
1 1
0805 1206
104 103
0.1 0603 0805
101 101 0.1 0603
2225 103
0.01 103 1206
102 1206
104
0.001 0.01
0.1 0.3 1 3 10 30 100 300 1,000 0.1 0.3 1 3 10 30 100 300 1,000
Frequency (MHz) Frequency (MHz)
FIGURE 4. Impedance versus Frequency C0G Dielectric FIGURE 5 Impedance versus Frequency X7R Dielectric

Impedance (Ohms) Impedance (Ohms)

30 10

10
1

3
0.1
1 0603
0805 104
104 Y5V 1206
1206 Y5V 104 0.01
0.3 105 Z5U
Y5V

0.1 0.001
0.1 1 10 100 1000
0.03 Frequency (MHz)
0.1 0.3 1 3 10 30 100 300 1,000
Frequency (MHz) C0603C105K8P AC C1206C105K8P AC
C0805C106K9P AC C1206C106K8P AC
FIGURE 6. Impedance versus Frequency Z5U/Y5V Dielectric
FIGURE 7. Impedence versus Frequency X5R Dielectric

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 57
 CERAMIC CHIP CAPACITORS

FEATURES
• C0G (NP0), X7R, X5R, Z5U and Y5V Dielectrics • Tape and reel packaging per EIA481-1. (See page
• 10, 16, 25, 50, 100 and 200 Volts 63 for specific tape and reel information.) Bulk
• Standard End Metalization: Tin-plate over nickel Cassette packaging (0402, 0603, 0805 only) per
barrier IEC60286-6 and EIAJ 7201.
• Available Capacitance Tolerances: ±0.10 pF; ±0.25 • RoHS Compliant
pF; ±0.5 pF; ±1%; ±2%; ±5%; ±10%; ±20%; and
+80%-20%
CAPACITOR OUTLINE DRAWINGS
TIN PLATE
L
W

T B

NICKEL PLATE
S
ELECTRODES CONDUCTIVE
METALLIZATION

DIMENSIONS—MILLIMETERS AND (INCHES)

EIA METRIC L# W# B S MOUNTING
SIZE CODE
SIZE CODE (Ref only) LENGTH WIDTH BANDWIDTH MIN. SEPARATION TECHNIQUE
0402* 1005 1.0 (.04) ± .05(.002) 0.5 (.02) ± .05 (.002) 0.20 (0.008)-0.40 (0.016) 0.3 (.012) Solder Reflow
0603* 1608 1.6 (.063) ± 0.15 (.006) 0.8 (.032) ± 0.15 (.006) 0.35 (.014) ±0.15 (.006) 0.7 (.028)
0805* 2012 2.0 (.079) ± 0.2 (.008) 1.25 (.049) ± 0.2 (.008)
See page 63 0.5 (.02) ±.25 (.010) 0.75 (.030) Solder Wave †
1206* 3216 3.2 (.126) ± 0.2 (.008) 1.6 (.063) ± 0.2 (.008)
for thickness 0.5 (.02) ±.25 (.010) N/A
or
Solder Reflow
1210* 3225 3.2 (.126) ± 0.2 (.008) 2.5 (.098) ± 0.2 (.008) dimensions. 0.5 (.02) ±.25 (.010) N/A
1812 4532 4.5 (.177) ± 0.3 (.012) 3.2 (.126) ± 0.3 (.012) 0.6 (.024) ±.35 (.014) N/A
1825* 4564 4.5 (.177) ± 0.3 (.012) 6.4 (.252) ± 0.4 (.016) 0.6 (.024) ±.35 (.014) N/A Solder
2220 5650 5.6 (.220) ± 0.4 (.016) 5.0 (.197) ± 0.4 (.016) 0.6 (.024) ±.35 (.014) N/A Reflow

2225 5664 5.6 (.220) ± 0.4 (.016) 6.3 (.248) ± 0.4 (.016) 0.6 (.024) ±.35 (.014) N/A

* Note: Indicates EIA Preferred Case Sizes (Tightened tolerances apply for 0402, 0603, and 0805 packaged in bulk cassette, see page 82.)
† For extended value 1210 case size – solder reflow only.

CAPACITOR ORDERING INFORMATION (Standard Chips - For

C 0805 C 103 K 5 R A C* Military see page 72)
CERAMIC END METALLIZATION
SIZE CODE C-Standard
SPECIFICATION (Tin-plated nickel barrier)
C - Standard FAILURE RATE LEVEL
CAPACITANCE CODE A- Not Applicable
Expressed in Picofarads (pF)
First two digits represent significant figures. TEMPERATURE CHARACTERISTIC
Third digit specifies number of zeros. (Use 9 Designated by Capacitance
Change Over Temperature Range
for 1.0 through 9.9pF. Use 8 for 0.5 through 0.99pF)
G – C0G (NP0) (±30 PPM/°C)
(Example: 2.2pF = 229 or 0.50 pF = 508)
R – X7R (±15%) (-55°C + 125°C)
CAPACITANCE TOLERANCE P– X5R (±15%) (-55°C + 85°C)
B – ±0.10pF J – ±5% U – Z5U (+22%, -56%) (+10°C + 85°C)
C – ±0.25pF K – ±10% V – Y5V (+22%, -82%) (-30°C + 85°C)
D – ±0.5pF M – ±20% VOLTAGE
F – ±1% P – (GMV) – special order only 1 - 100V 3 - 25V
G – ±2% Z – +80%, -20% 2 - 200V 4 - 16V
5 - 50V 8 - 10V
* Part Number Example: C0805C103K5RAC (14 digits - no spaces) 9 - 6.3V
58 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 CERAMIC CHIP/STANDARD

C0G CAPACITANCE RANGE – 0402, 0603, 0805, 1206

Cap Cap Cap C0402* C0603* C0805* C1206*
pF Code Tol. 10V 16V 25V 50V 10V 16V 25V 50V 100V 200V 10V 16V 25V 50V 100V 200V 10V 16V 25V 50V 100V 200V
0.50 508 C,D BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC
0.75 758 C,D BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC
1.0 109 C,D BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
1.1 119 C,D BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
1.2 129 C,D BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
1.5 159 C,D BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
1.6 169 C,D BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
1.8 189 C,D BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
2.0 209 C,D BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
2.2 229 C,D BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
2.4 249 C,D BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
2.7 279 C,D K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
3.0 309 C,D K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
3.3 339 C,D K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
3.9 399 C,D K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
4.3 439 C,D K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
4.7 479 C,D K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
5.1 519 C,D K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
5.6 569 C,D J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
6.0 609 C,D J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
6.2 629 C,D J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
6.8 689 C,D J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
7.0 709 C,D J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
7.5 759 C,D J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
8.2 829 C,D J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
9.1 919 C,D J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
10.0 100 C,D J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
11.0 110 C,D J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
12.0 120 C,D J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
13.0 130 C,D J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
15.0 150 C,D G,J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
16.0 160 C,D G,J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
18.0 180 C,D G,J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
20.0 200 C,D G,J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
22.0 220 C,D G,J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
24.0 240 C,D G,J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
27.0 270 D,F,G,J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
30.0 300 D,F,G,J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
33.0 330 D,F,G,J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
36.0 360 D,F,G,J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
39.0 390 D,F,G,J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
43.0 430 D,F,G,J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
47.0 470 D,F,G,J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
51.0 510 D,F,G,J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
56.0 560 F,G,J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
62.0 620 F,G,J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
68.0 680 F,G,J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
75.0 750 F,G,J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
82.0 820 F,G,J,K,M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
91.0 910 F,G,J,K,M BB BB BB BB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
100.0 101 F,G,J,K,M BB BB BB BB CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
110.0 111 F,G,J,K,M CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
120.0 121 F,G,J,K,M CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
130.0 131 F,G,J,K,M CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
150.0 151 F,G,J,K,M CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
160.0 161 F,G,J,K,M CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
180.0 181 F,G,J,K,M CB CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
200.0 201 F,G,J,K,M CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
220.0 221 F,G,J,K,M CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
240.0 241 F,G,J,K,M CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
270.0 271 F,G,J,K,M CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
300.0 301 F,G,J,K,M CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB

Ceramic Surface Mount

330.0 331 F,G,J,K,M CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
360.0 361 F,G,J,K,M CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
390.0 391 F,G,J,K,M CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
430.0 431 F,G,J,K,M CB CB CB CB DC DC DC DC DC DC EB EB EB EB EB EB
470.0 471 F,G,J,K,M CB CB CB CB DC DC DC DC DC DD EB EB EB EB EB EB
510.0 511 F,G,J,K,M CB CB CB CB DC DC DC DC DC EB EB EB EB EB EB
560.0 561 F,G,J,K,M CB CB CB CC DC DC DC DC DC EB EB EB EB EB EB
620.0 621 F,G,J,K,M CB CB CB CC DC DC DC DC DC EB EB EB EB EB EC
680.0 681 F,G,J,K,M CB CB CB CC DC DC DC DC DC EB EB EB EB EB EC
750.0 751 F,G,J,K,M CB CB CB CC DC DC DC DC DC EB EB EB EB EB EC
820.0 821 F,G,J,K,M CB CB CB CC DC DC DC DC DC EB EB EB EB EB EC
910.0 911 F,G,J,K,M CB CB CB CC DC DC DC DC DD EB EB EB EB EB ED
1000.0 102 F,G,J,K,M CB CB CB CC DC DC DC DC DD EB EB EB EB EB EE
1100.0 112 F,G,J,K,M DC DC DC DC EB EB EB EB EB EB
1200.0 122 F,G,J,K,M DC DC DC DC EB EB EB EB EB EB
1300.0 132 F,G,J,K,M DD DD DD DD EB EB EB EB EC EC
1500.0 152 F,G,J,K,M DD DD DD DD EB EB EB EB ED EC
1600.0 162 F,G,J,K,M DD DD DD DD EB EB EB EB ED ED
1800.0 182 F,G,J,K,M DD DD DD DD EB EB EB EB ED ED
2000.0 202 F,G,J,K,M DC DC DC EB EB EB EB ED
2200.0 222 F,G,J,K,M DC DC DC EB EB EB EB ED
2400.0 242 F,G,J,K,M DC DC DC EB EB EB EB EC
2700.0 272 F,G,J,K,M DC DC DC EB EB EB EB EC
3000.0 302 F,G,J,K,M DD DD DD EC EC EC EC EC
3300.0 332 F,G,J,K,M DD DD DD EC EC EC EC EC
3600.0 362 F,G,J,K,M DD DD DD EC EC EC EC EE
3900.0 392 F,G,J,K,M DE DE DE EC EC EC EC EF
4300.0 432 F,G,J,K,M EC EC EC EC
4700.0 472 F,G,J,K,M EC EC EC EC
5100.0 512 F,G,J,K,M ED ED ED ED
5600.0 562 F,G,J,K,M ED ED ED ED
6200.0 622 F,G,J,K,M EB EB EB
6800.0 682 F,G,J,K,M EB EB EB
7500.0 752 F,G,J,K,M EB EB EB
8200.0 822 F,G,J,K,M EC EC EC
9100.0 912 F,G,J,K,M EC EC EC
10,000.0 103 F,G,J,K,M ED ED ED

* Indicates EIA preferred chip sizes.

NOTE: For non-standard capacitance values or voltages, contact your local KEMET sales representative.
50 Volt Ceramic Chips can be used in 63 volt applications.

Improved product with higher ratings and tighter capacitance tolerance product may be substituted within the same size (length, width, and thickness) at KEMET’s option.
Reels with such substitutions will be marked with the improved KEMET part numbers.

See page 63 for Thickness Code Reference Chart.

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 59
 I
CERAMIC CHIP/STANDARD
C0G CAPACITANCE RANGE – 1210, 1812, 1825, 2220, 2225
Cap Cap Cap C1210*
C1210* C1812*
C1812* C1825*
C1825* C2220
C2220 C2225
C2225
pF Code Tol. 50V100V
50V 100V 200V
200V 50V
50V 100V
100V 200V
200V 50V
50V 100V
100V 200V
200V50V
50V100V
100V200V 50V50V
200V 100V100V
200V200V
10 100 D J,K,M FB FB FB
12 120 D J,K,M FB FB FB
15 150 D G,J,K,M FB FB FB
18 180 D G,J,K,M FB FB FB
22 220 D G,J,K,M FB FB FB
27 270 D,F,G,J,K,M FB FB FB
33 330 D,F,G,J,K,M FB FB FB
39 390 D,F,G,J,K,M FB FB FB
47 470 D,F,G,J,K,M FB FB FB
56 560 F,G,J,K,M FB FB FB
68 680 F,G,J,K,M FB FB FB
82 820 F,G,J,K,M FB FB FB
100 101 F,G,J,K,M FB FB FB
120 121 F,G,J,K,M FB FB FB
150 131 F,G,J,K,M FB FB FB
180 181 F,G,J,K,M FB FB FB
220 221 F,G,J,K,M FB FB FB
270 271 F,G,J,K,M FB FB FB
330 331 F,G,J,K,M FB FB FB
390 391 F,G,J,K,M FB FB FB
470 471 F,G,J,K,M FB FB FB GB
GB GB
GB GB
GB
560 561 F,G,J,K,M FB FB FB GB
GB GB
GB GB
GB
680 681 F,G,J,K,M FB FB FB GB
GB GB
GB GB
GB
820 821 F,G,J,K,M FB FB FB GB
GB GB
GB GB
GB
1,000 102 F,G,J,K,M FB FB FB GB
GB GB
GB GB
GB
1,200 122 F,G,J,K,M FB FB FB GB
GB GB
GB GB
GB
1,500 152 F,G,J,K,M FB FB FE GB
GB GB
GB GB
GB
1,800 182 F,G,J,K,M FB FB FE GB
GB GB
GB GB
GB
2,200 222 F,G,J,K,M FB FC FG GB
GB GB
GB GB
GB
2,700 272 F,G,J,K,M FB FC FC GB
GB GB
GB GB
GB
3,300 332 F,G,J,K,M FB FF FF GB
GB GB
GB GB
GB
3,900 392 F,G,J,K,M FB FF GB
GB GB
GB GB
GB HB
HB HB
HB HBHB
4,700 472 F,G,J,K,M FF FF GB
GB GB
GB GD
GD HB
HB HB
HB HBHB KB KBKB KBKB KB
5,600 562 F,G,J,K,M FB FF GB
GB GB
GB GH
GH HB
HB HB
HB HBHB KB KBKB KBKB KB
6,800 682 F,G,J,K,M FB FG GB
GB GB
GB GJ HB
HB HB
HB HBHB JB JB JBJB KB KBKB KBKB KB
8,200 822 F,G,J,K,M FC GB
GB GB
GB HB
HB HB
HB HBHB JB JB JBJB KB KBKB KBKB KB
10,000 103 F,G,J,K,M FF GB
GB GD
GD HB
HB HB
HB HEHE JB JB JBJB KB KBKB KBKB KB
12,000 123 F,G,J,K,M FG GB GD HB
HB HB
HB HEHE JB JB JB JB KB KBKB KBKB KB
15,000 153 F,G,J,K,M HB
HB HB
HB JB JB JBJB KB KBKB KBKE KE
18,000 183 F,G,J,K,M HB
HB HB
HB JB JB JBJB KB KBKB KB
22,000 223 F,G,J,K,M HB
HB HE
HE JB JB KB KBKB KB
I 27,000 273 F,G,J,K,M HB
HB HE
HE JB JB KB KBKB KB
33,000 333 F,G,J,K,M KB KB
X7R CAPACITANCE RANGE – 0402, 0603, 0805, 1206
Cap Cap Cap C0402* C0603* C0805* C1206*
pF Code Tol. 6.3V 10V 16V 25V 50V 6.3V 10V 16V 25V 50V 100V 200V 6.3V 10V 16V 25V 50V 100V 200V 6.3V 10V 16V 25V 50V 100V 200V
150 151 K,M,J BB BB BB BB BB
180 181 K,M,J BB BB BB BB BB CB CB CB CB CB CB CB
220 221 K,M,J BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC
270 271 K,M,J BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC
330 331 K,M,J BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC
390 391 K,M,J BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC
470 471 K,M,J BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC
560 561 K,M,J BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC
680 681 K,M,J BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC
820 821 K,M,J BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC
1,000 102 K,M,J BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC EB EB EB EB EB EB EB
1,200 122 K,M,J BB BB BB BB BB CB CB CB CB CB CB CC DC DC DC DC DC DC DC EB EB EB EB EB EB EB
1,500 152 K,M,J BB BB BB BB BB CB CB CB CB CB CB CC DC DC DC DC DC DC DC EB EB EB EB EB EB EB
1,800 182 K,M,J BB BB BB BB BB# CB CB CB CB CB CB CC DC DC DC DC DC DC DC EB EB EB EB EB EB EB
2,200 222 K,M,J BB BB BB BB BB# CB CB CB CB CB CB CC DC DC DC DC DC DC DC EB EB EB EB EB EB EB
2,700 272 K,M,J BB BB BB BB BB# CB CB CB CB CB CB CC DC DC DC DC DC DC DC EB EB EB EB EB EB EB
3,300 332 K,M,J BB BB BB BB BB# CB CB CB CB CB CB CC DC DC DC DC DC DC DC EB EB EB EB EB EB EB
3,900 392 K,M,J BB BB BB BB BB# CB CB CB CB CB CB CC DC DC DC DC DC DC DC EB EB EB EB EB EB EB
4,700 472 K,M,J BB BB BB BB BB# CB CB CB CB CB CB CC DC DC DC DC DC DC DC EB EB EB EB EB EB EB
5,600 562 K,M,J BB BB BB BB BB# CB CB CB CB CB CB CC DC DC DC DC DC DC DC EB EB EB EB EB EB EB
6,800 682 K,M,J BB BB BB BB BB# CB CB CB CB CB CB CC DC DC DC DC DC DC DC EB EB EB EB EB EB EB
8,200 822 K,M,J BB BB BB BB BB# CB CB CB CB CB CB CC DC DC DC DC DC DC DC EB EB EB EB EB EB EB
10,000 103 K,M,J BB BB BB BB BB# CB CB CB CB CB CB CC DC DC DC DC DC DC DC EB EB EB EB EB EB EB
12,000 123 K,M,J** BB BB BB CB CB CB CB CB CC DC DC DC DC DC DC DC EB EB EB EB EB EB EB
15,000 153 K,M,J** BB BB BB CB CB CB CB CB CC DD DD DD DD DD DD DC EB EB EB EB EB EB EB
18,000 183 K,M,J** BB BB BB CB CB CB CB CB CC DC DC DC DC DC DD DC EB EB EB EB EB EB EB
22,000 223 K,M,J** BB BB BB CB CB CB CB CB CC DC DC DC DC DC DD DC EB EB EB EB EB EB EB
27,000 273 K,M,J** BB BB BB CB CB CB CB CB CC DC DC DC DC DC DD DE EB EB EB EB EB EB EB
33,000 333 K,M,J** BB BB BB CB CB CB CB CB CC DC DC DC DC DC DD DE EB EB EB EB EB EB EB
39,000 393 K,M,J** BB BB BB CB CB CB CB CB CC DD DD DD DD DD DD DE EB EB EB EB EB EC EB
47,000 473 K,M,J** BB BB BB CB CB CB CB CB DD DD DD DD DD DE DG EB EB EB EB EB EC ED
56,000 563 K,M,J** BB BB BB CB CB CB CB CC DD DD DD DD DD# DE DG EB EB EB EB EB EB ED
68,000 683 K,M,J** BB BB BB CB CB CB CB CC DD DD DD DD DD# DE EB EB EB EB EB EB ED
82,000 823 K,M,J** BB BB BB CB CB CB CB CC DD DD DD DD DD# DE EB EB EB EB EB EB ED
100,000 104 K,M,J** BB BB BB CB# CB# CB# CB# CC# DD DD DD DD DD# DE EB EB EB EB EB EB EM
120,000 124 K,M,J** CB# CB# CB# DC DC DC DC DD# DG EC EC EC EC EC EC EM
150,000 154 K,M,J** CB# CB# CB# DC DC DC DC DD# EC EC EC EC EC EC EG
180,000 184 K,M,J** CB# CB# CB# DC DC DC DC DD# EC EC EC EC EC# EC#
220,000 224 K,M,J** CB# CB# CB# DC DC DC DC DD# EC EC EC EC EC# EC#
270,000 274 K,M,J** CB# CB# CB# DD DD DD DD EB EB EB EB EC# EM
330,000 334 K,M,J** CB# CB# CB# DE DE DE DE EB EB EB EB EC# EG
390,000 394 K,M,J** CB# CB# CB# DG DG DG DG EB EB EB EB EG# EG
470,000 474 K,M,J** CB# CB# CB# DG DG DG DG EC EC EC EC EC#
560,000 564 K,M,J** DG DG DG DG ED ED ED ED EC#
680,000 684 K,M,J** DG DG DG EE EE EE EE ED#
820,000 824 K,M,J* DG DG DG EF EF EF EF
1,000,000 105 K,M,J** DG DG DG EE EE EF EG
1,200,000 125 K,M,J** DE DE DE ED ED ED EG
1,500,000 155 K,M,J** DG DG DG EF EF EF EG
1,800,000 185 K,M,J** DG DG DG EF EF EF
2,200,000 225 K,M,J** DG DG DG EG EG EG
2,700,000 275 K,M,J** EN EN EK
3,300,000 335 K,M,J** ED ED ED
3,900,000 395 K,M,J** EL EL EL
4,700,000 475 K,M,J** EM EM EM
5,600,000 565 K,M,J** EH EH EH
6,800,000 685 K,M,J** EH EH EH
8,200,000 825 K,M,J** EH EH
10,000,000 106 K,M,J** EH EH

* Indicates EIA preferred chip sizes. NOTE: For non-standard apacitance values or voltages, contact your local KEMET sales representative. #X7R dielectric - Extended
Range Values - Cap and DF measured @ 0.5 Vms. Improved product with higher ratings and tighter tolerance product may be substituted within the same size
(length, width, and thickness) at KEMET's option. Reels with substitutions will be marked with the improved KEMET part numbers. **Contact KEMET Sales for "J"
tolerance availability.
60 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 CERAMIC CHIP/STANDARD

X7R CAPACITANCE RANGE – 1210, 1812, 1825, 2220, 2225

CAP.
Cap CAP
Cap CAP.
Cap C1210*
C1210* C1812*
C1812* C1825*
C1825* C2220
C2220 C2225
C2225
PF
pF CODE
Code TOL.
Tol. 6.3V
6.3V 10V 16V 25V
10V 16V 25V 50V
50V100V
100V200V 50V100V
200V50V 100V200V
200V 50V100V
50V 100V200V
200V50V
50V 100V
100V 200V
200V 50V 100V
50V 100V 200V
200V
2200
2,200 222
222 K,M,J FB
K,M,J FB FB FB
FB FB FB FB FBFB FBFB FBFB
2700
2,700 272
272 K,M,J
K,M,J FB
FB FB
FB FBFB FB
FB FBFB FBFB FBFB
3300 332
3,300 332 K,M,J FB
K,M,J FB FB FB
FB FB FB FB FBFB FBFB FBFB
3900
3,900 392
392 K,M,J FB
K,M,J FB FB FB
FB FB FB FB FBFB FBFB FBFB
4700
4,700 472
472 K,M,J FB
K,M,J FB FB FB
FB FB FB FB FBFB FBFB FBFB
5600 562
5,600 562 K,M,J FB
K,M,J FB FB FB
FB FB FB FB FBFB FBFB FBFB
6800
6,800 682
682 K,M,J FB
K,M,J FB FB FB
FB FB FB FB FBFB FBFB FBFB GBGB GBGB GBGB
8200
8,200 822
822 K,M,J FB
K,M,J FB FB FB
FB FB FB FB FBFB FBFB FBFB GBGB GBGB GBGB
10,000 103
10,000 103 K,M,J
K,M,J FB
FB FB
FB FBFB FB FBFB FBFB FBFB GBGB GBGB GBGB
FB
12,000
12,000 123
123 K,M,J FB
K,M,J FB FB FB
FB FB FB FB FBFB FBFB FBFB GBGB GBGB GBGB
15,000
15,000 153
153 K,M,J FB
K,M,J FB FB FB
FB FB FB FB FBFB FBFB FBFB GBGB GBGB GBGB
18,000
18,000 183
183 K,M,J FB
K,M,J FB FB FB
FB FB FB FB FBFB FBFB FBFB GBGB GBGB GBGB
22,000 223
22,000 223 K,M,J
K,M,J FB
FB FB
FB FBFB FB FBFB FBFB FBFB GBGB GBGB GBGB HBHB HBHB HB
FB HB
27,000
27,000 273
273 K,M,J FB
K,M,J FB FB FB
FB FB FB FB FBFB FBFB FBFB GBGB GBGB GBGB HBHB HBHB HB HB
33,000
33,000 333
333 K,M,J FB
K,M,J FB FB FB
FB FB FB FB FBFB FBFB FBFB GBGB GBGB GBGB HBHB HBHB HB HB
39,000 393
39,000 393 K,M,J
K,M,J FB
FB FB
FB FBFB FB
FB FBFB FBFB FBFB GB GB GBGB GB GB HBHB HBHB HB HB
47,000
47,000 473
473 K,M,J FB
K,M,J FB FB FB
FB FB FB FB FBFB FBFB FCFC GBGB GBGB GBGB HBHB HBHB HB HB KC
KC KC
KC KC
KC
56,000
56,000 563
563 K,M,J FB
K,M,J FB FB FB
FB FB FB FB FBFB FBFB FCFC GBGB GBGB GBGB HBHB HBHB HB HB KC
KC KC
KC KC
KC
68,000 683
68,000 683 K,M,J
K,M,J FB
FB FB FB
FB FB FB FB FBFB FBFB FCFC GB GB GB GB GB GB HBHB HBHB HB HB KC
KC KC
KC KC
KC
82,000
82,000 823
823 K,M,J FB
K,M,J FB FB FB
FB FB FB FB FC FC FCFC FFFF GBGB GBGB GBGB HBHB HBHB HB HB KC
KC KC
KC KC
KC
100,000
100,000 104
104 K,M,J FB
K,M,J FB FB FB
FB FB FB FB FBFB FDFD FGFG GBGB GBGB GBGB HBHB HBHB HB HB KC
KC KC
KC KC
KC
120,000
120,000 124
124 K,M,J FB
K,M,J FB FB FB
FB FB FB FB FBFB FDFD GBGB GBGB GBGB HBHB HBHB HB HB KC
KC KC
KC KC
KC
150,000
150,000 154
154 K,M,J
K,M,J FC
FC FC
FC FCFC FC
FC FC FC FDFD GB GB GBGB GE GE HBHB HBHB HB HB KC
KC KC
KC KC
KC
180,000
180,000 184
184 K,M,J FC
K,M,J FC FC FC
FC FC FC FC FC FC FDFD GBGB GBGB GGGG HBHB HBHB HB HB KC
KC KC
KC KC
KC
220,000
220,000 224
224 K,M,J FC
K,M,J FC FC FC
FC FC FC FC FC FC FDFD GBGB GBGB HBHB HBHB HB HB KC
KC KC
KC KC
KC
270,000 274
270,000 274 K,M,J
K,M,J FC
FC FC FC
FC FC FC FC FC#FC#FD#FD# GB GB GHGH HBHB HBHB HB HB JC JC JC JC JC
JC KB
KB KC
KC KC
KC
330,000
330,000 334
334 K,M,J FD
K,M,J FD FD FD
FD FD FD FD FD#FD#FD#FD# GBGB GHGH HBHB HBHB HB HB JC JC JC JC JC
JC KB
KB KC
KC KC
KC
390,000
390,000 394
394 K,M,J FD
K,M,J FD FD FD
FD FD FD FD FD#FD# GBGB HBHB HBHB HD HD JC JC JC JC JC
JC KB
KB KC
KC KC
KC
470,000
470,000 474
474 K,M,J FD
K,M,J FD FD FD
FD FD FD FD FD#FD# GBGB HBHB HBHB JC JC
JC JC KB
KB KC
KC KD
KD
560,000 564
560,000 564 K,M,J FD
FD FD
FD FDFD FD
FD FD# FD# GC GC HBHB HDHD JC
JC JC
JC KB
KB KC
KC
680,000
680,000 684
684 K,M,J FD
FD FD FD
FD FD FD FD FD#FD# GCGC HBHB HDHD JC JD
JC JD KB
KB KC
KC
820,000
820,000 824
824 K,M,J FF
FF FF FF FF
FF FF FF#FF# GEGE HBHB JC JF
JC JF KB
KB KC
KC
1,000,000 105
1,000,000 105 K,M,J FH
FH FH FH
FH FH FH FH FH#FH# GE GE HBHB JC
JC KB
KB KD
KD
1,200,000
1,200,000 125
125 K,M,J FH
FH FH FH
FH FH FH FH HBHB JC
JC KB
KB
1,500,000
1,500,000 155
155 K,M,J FH
FH FH FH
FH FH FH FH HBHB JC
JC KC
KC
1,800,000
1,800,000 185
185 K,M,J FH
FH FH FH
FH FH FH FH HDHD JD
JD KD
KD
2,200,000
2,200,000 225
225 K,M,J FJ
FJ FJ FJ FJ
FJ FJ HFHF JF
JF KD
KD
* Indicates EIA preferred chip sizes.
NOTE: For non-standard capacitance values or voltages, contact your local KEMET sales representative.
50 Volt Ceramic Chips can be used for 63 volt applications.
# Extended Range Values – Cap and DF measured @ 0.5 Vrms.
Improved product with higher ratings and tighter capacitance tolerance product may be substituted within the same size (length, width, and thickness) at KEMET's option.
Reels with such substitutions will be marked with the improved KEMET part numbers.
X5R CAPACITANCE RANGE
Cap Cap Cap C0402* C0603* C0805* C1206* C1210*
pF Code Tol. 6.3V 10V 6.3V 10V 16V 6.3V 10V 16V 25V 6.3V 10V 16V 25V 6.3V 10V 16V 25V 50V
12,000 123 K,M BB BB
15,000 153 K,M BB BB
18,000 183 K,M BB BB
22,000 223 K,M BB BB
27,000 273 K,M BB BB
33,000 333 K,M BB BB
39,000 393 K,M BB BB
47,000 473 K,M BB BB

Ceramic Surface Mount

56,000 563 K,M BB BB
68,000 683 K,M BB BB
82,000 823 K,M BB BB
100,000 104 K,M BB BB
120,000 124 K,M BB
150,000 154 K,M BB
180,000 184 K,M BB
220,000 224 K,M BB
270,000 274 K,M BB CC CC CC EB
330,000 334 K,M BB CC CC CC EB
390,000 394 K,M BB CC CC CC EB
470,000 474 K,M BB CC CC CC DC EC
560,000 564 K,M BB CC CC CC DD ED
680,000 684 K,M BB CC CC CC DE EE
820,000 824 K,M BB CC CC CC DF EF
1,000,000 105 K,M BB CC CC CC DG EH FH+ FH+ FH+
1,200,000 125 K,M CC DD DD DD EC FD+ FD+
1,500,000 155 K,M CC DE DE DE EC EC EC EC FD+ FD+
1,800,000 185 K,M CC DH DH DH EC EC EC EC FD+ FD+
2,200,000 225 K,M CC DH DH DH EE EE EE EE FG+ FG+
2,700,000 275 K,M CD DD DD DD EF EF EF EF FG+ FG+
3,300,000 335 K,M CD DE DE DH EH EH EH EH FH+ FH+
4,700,000 475 K,M CD DH DH DH EH EH EH EH FK+ FK+ FK+ FK+
6,800,000 685 K,M DH EK EK EH FJ+ FJ+ FJ+ FJ+
8,200,000 825 K,M DH EK EK EH FK+ FK+ FK+ FK+
10,000,000 106 K,M DH EL EL EH FK+ FK+ FK+ FK+
12,000,000 126 K,M EH FD+ FD+ FG+
15,000,000 156 K,M EH FD+ FD+ FL+
18,000,000 186 K,M EH FL+ FL+ FH+
22,000,000 226 K,M EH FH+ FH+ FJ+
27,000,000 276 K,M FM+
33,000,000 336 K,M FM+
39,000,000 396 K,M FM+
47,000,000 476 K,M FM+
Improved product with higher ratings and tighter capacitance tolerance product may be substituted within the same size (length, width, and thickness) at KEMET's option.
Reels with such substitutions will be marked with the improved KEMET part numbers.
NOTE: For non-standard capacitance values or voltages, contact your local KEMET sales representative.
+ Reflow Only
See page 63 for Thickness Code Reference Chart.
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 61
 CERAMIC CHIP/STANDARD
Z5U CAPACITANCE RANGE
(KEMET's Z5U also meets Y5V Characteristics)
CAP.
Cap CapCAP Cap C0805*
CAP C0805* C1206*
C1206* C1210*
C1210* C1812*
C1812* C1825*
C1825* C2225
C2225
PF
pF CODETol.
Code 50V 100V
TOL 50V 100V 50V
50V 100V
100V 50V
50V 100V 50V 100V
100V 50V 100V 50V
50V 100V
100V 50V 100V
50V 100V
6800
6,800 682682 M,Z
M,Z DCDC DCDC
8200
8,200 822822 M,Z
M,Z DCDC DCDC
10,000
10,000 103103 M,Z
M,Z DCDC DCDC EB EB EBEB
12,000
12,000 123123 M,Z
M,Z DCDC EBEB EBEB
15,000
15,000 153153 M,Z
M,Z DCDC EBEB EBEB
18,000
18,000 183183 M,Z
M,Z DCDC EBEB EBEB
22,000
22,000 223223 M,Z
M,Z DCDC EBEB EB
EB
27,000
27,000 273273 M,Z
M,Z DCDC EBEB EB
EB
33,000
33,000 333333 M,Z
M,Z DCDC EBEB EBEB
39,000
39,000 393393 M,Z
M,Z DDDD EBEB EC
EC
47,000
47,000 473473 M,Z
M,Z DDDD EBEB EC FB
EC FB FBFB
56,000
56,000 563563 M,Z
M,Z DDDD EBEB EBEB FB FB FBFB
68,000
68,000 683683 M,Z
M,Z DDDD EBEB EBEB FB FB FBFB
82,000
82,000 823823 M,Z
M,Z DDDD EBEB EB
EB FBFB FC GB
FC GB GB GB
100,000
100,000 104104 M,Z
M,Z DDDD EBEB EBEB FB FB FDFD GBGB GB GB
120,000
120,000 124124 M,Z
M,Z ECEC FBFB FDFD GBGB GB GB
150,000
150,000 154154 M,Z
M,Z ECEC FCFC FD
FD GB
GB GB
GB
180,000
180,000 184184 M,Z
M,Z ECEC FCFC GB
GB HB HB
HB HB
220,000
220,000 224224 M,Z
M,Z ECEC FCFC GB
GB HB HB
HB HB
270,000
270,000 274274 M,Z
M,Z FCFC GB
GB HB HB
HB HB
330,000
330,000 334334 M,Z
M,Z FDFD GB
GB HB
HB HB
HB KB
KB KC
KC
390,000
390,000 394394 M,Z
M,Z FDFD GB
GB HB HD
HB HD KB
KB KC
KC
470,000
470,000 474474 M,Z
M,Z FDFD GB
GB HB
HB KB
KB KC
KC
560,000
560,000 564564 M,Z
M,Z FDFD GC
GC HB
HB KB
KB
680,000
680,000 684684 M,Z
M,Z FDFD GC
GC HB
HB KB
KB
820,000
820,000 824824 M,Z
M,Z FF
FF GE
GE HB
HB KB
KB
1,000,000
1,000,000 105105 M,Z
M,Z FHFH GE
GE HB
HB KB
KB
1,200,000
1,200,000 125125 M,Z
M,Z HB
HB KB
KB
1,500,000
1,500,000 155155 M,Z
M,Z HB
HB KC
KC
1,800,000
1,800,000 185185 M,Z
M,Z HB
HB KD
KD
2,200,000
2,200,000 225225 M,Z
M,Z HB
HB KD
KD
2,700,000
2,700,000 275275 M,Z
M,Z KD
KD
NOTE: For non-standard capacitance values or voltages, contact your local KEMET sales representative.
50 Volt Ceramic Chips can be used for 63 volt applications.
* EIA preferred chip sizes

Y5V CAPACITANCE RANGE

Cap
Cap. CapCAPCapCap. C0402* C0402 C0603*
C0603 C0805*
C0805 C1206*
C1206 C1210*
C1210
pFpF CODE
Code Tol.Tol.6.3V
6.3V10V
10V16V 6.3V 10V
16V 6.3V 10V 16V
16V 25V 6.3V 10V 16V
25V 6.3V 16V 25V
25V 50V 6.3V 10V
10V 16V 25V 10V 16V
25V 50V 6.3V 10V 16V 25V 50V
25V 50V
22,000 223 223 Z Z
22,000 DC
DC EB
EB
33,000 333 333 Z Z
33,000 DC
DC EB
EB
47,000 473 473 Z Z BB
47,000 BB BB BB BBBB DD
DD EB
EB
68,000 683 683 Z Z BB
68,000 BB BB BB BBBB DD
DD EB
EB
100,000 104 104 Z Z BB
100,000 BB BB BB BBBB CBCB CBCB CBCB CB
CB DD
DD EB
EB
150,000 154 154 Z Z
150,000 CB CB
CB CB CBCB CB DC
CB DC DC
DC DCDC DC
DC EC
EC
220,000 224 224 Z Z
220,000 CB CB
CB CB CBCB CB DC
CB DC DC
DC DCDC DC
DC EC
EC FD+ FD+
FD+ FD+
330,000 334 334 Z Z
330,000 CB CB
CB CB CBCB CB DC
CB DC DC
DC DCDC DC
DC EB
EB FD+ FD+
FD+ FD+
470,000 474 474 Z Z
470,000 CC CC
CC CC DC DC DC
DC DC DC DC
DC EC
EC FD+ FD+
FD+ FD+
680,000 684 684 Z Z
680,000 CC CC
CC CC DE DE DE
DE DE DE DE
DE EB
EB FD+ FD+
FD+ FD+
1,000,000 105 105 Z Z
1,000,000 CC CC
CC CC DG DG DG
DG DG DG DG
DG EB
EB FH+ FH+
FH+ FH+
1,500,000 155 155 Z Z
1,500,000 DG DG DG
DG DG DG EC
EC EC
EC EC
EC FD+
FD+
2,200,000 225 225 Z Z
2,200,000 DG DG DG
DG DG DG ED
ED ED
ED ED
ED FD+
FD+
3,300,000 335 335 Z Z
3,300,000 DE
DE DE
DE EF
EF EF
EF EF
EF FE+
FE+
4,700,000 475 475 Z Z
4,700,000 DG
DG DGDG E
EF EJ
EF EJ
EF FG+
FG+ FG+
FG+ FG+
FG+
6,800,000 685 685 Z Z
6,800,000 DH
DH EJ
EJ EJ
EJ FH+
FH+ FH+
FH+ FH+
FH+
10,000,000 106 106 Z Z
10,000,000 DH
DH EJ
EJ EJ
EJ FH+
FH+ FH+
FH+ FH+
FH+
15,000,000 156 156 Z Z
15,000,000 EJ
EJ FD+
FJ+ FD+
FJ+ FL+
22,000,000 226 226 Z Z
22,000,000 EJ
EJ FK+
FH+ FK+
FH+ FJ+
NOTE: For non-standard capacitance values or voltages, contact your local KEMET sales representative.
50 Volt Ceramic Chips can be used for 63 volt applications.
* EIA preferred chip sizes
+ Reflow only
Improved product with higher ratings and tighter capacitance tolerance product may be substituted within the same size (length, width, and thickness) at KEMET’s option.
Reels with such substitutions will be marked with the improved KEMET part numbers.

See page 63 for Thickness Code Reference Chart.

SURFACE MOUNT LAND DIMENSIONS - CERAMIC CHIP CAPACITORS - MM

Grid
Grid
placement Reflow Solder Wave Solder
Placement
courtyard
Dimension Z G X Y(ref) C(ref) Z G X Y(ref) Smin
CourtyardC 0402 2.14 0.28 0.74 0.93 1.21 Not Recommended
0603 2.78 0.68 1.08 1.05 1.73 3.18 0.68 0.80 1.25 1.93
C 0805 3.30 0.70 1.60 1.30 2.00 3.70 0.70 1.10 1.50 2.20
1206 4.50 1.50 2.00 1.50 3.00 4.90 1.50 1.40 1.70 3.20
1210 4.50 1.50 2.90 1.50 3.00 4.90 1.50 2.00 1.70 3.20
1812 5.90 2.30 3.70 1.80 4.10
X
X 1825 5.90 2.30 6.90 1.80 4.10
Not Recommended
2220 7.00 3.30 5.50 1.85 5.15
2225 7.00 3.30 6.80 1.85 5.15
Calculation Formula
GG Y Z = Lmin + 2Jt + Tt
G = Smax - 2Jh -Th
Y Z X = Wmin + 2Js + Ts
Z Tt, Th, Ts = Combined tolerances

62 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 CERAMIC CHIP CAPACITORS

THICKNESS CODE REFERENCE CHART

PACKAGING QTY BASED ON FINISHED CHIP THICKNESS SPECIFICATIONS
Thickness Chip Chip Thickness Qty per Reel Qty per Reel Qty per Reel Qty per Reel Qty per Bulk
Code Size Range (mm) 7" Plastic 13" Plastic 7" Paper 13" Paper Cassette

AA 0201 .30 ± .03 N/A N/A 15,000 N/A N/A

BB 0402 .50 ± .05 N/A N/A 10,000 50,000 50,000
CB 0603 .80 ± .07 N/A N/A 4,000 10,000 15,000
CC 0603 .80 ± .10 N/A N/A 4,000 10,000 N/A
CD 0603 .80 ± .15 N/A N/A 4,000 10,000 N/A
DB 0805 .60 ± .10 N/A N/A N/A N/A 10,000
DC 0805 .78 ± .10 4,000 10,000 4,000 10,000 N/A
DD 0805 .90 ± .10 4,000 10,000 N/A N/A N/A
DE 0805 1.00 ± .10 2,500 10,000 N/A N/A N/A
DF 0805 1.10 ± .10 2,500 10,000 N/A N/A N/A
DG 0805 1.25 ± .15 2,500 10,000 N/A N/A N/A
DH 0805 1.25 ± .20 2,500 10,000 N/A N/A N/A
EB 1206 .78 ± .10 4,000 10,000 4,000 10,000 N/A
EC 1206 .90 ± .10 4,000 10,000 N/A N/A N/A
ED 1206 1.00 ± .10 2,500 10,000 N/A N/A N/A
EE 1206 1.10 ± .10 2,500 10,000 N/A N/A N/A
EF 1206 1.20 ± .15 2,500 10,000 N/A N/A N/A
EG 1206 1.60 ± .15 2,000 8,000 N/A N/A N/A
EH 1206 1.60 ± .20 2,000 8,000 N/A N/A N/A
EJ 1206 1.70 ± .20 2,000 8,000 N/A N/A N/A
EK 1206 .80 ± .10 2,000 8,000 N/A N/A N/A
EL 1206 1.15 ± .15 2,000 8,000 N/A N/A N/A
EM 1206 1.25 ± .15 2,500 10,000 N/A N/A N/A
EN 1206 0.95 ± 0.1 4,000 10,000 N/A N/A N/A
FB 1210 .78 ± .10 4,000 10,000 N/A N/A N/A
FC 1210 .90 ± .10 4,000 10,000 N/A N/A N/A
FD 1210 .95 ± .10 4,000 10,000 N/A N/A N/A
FE 1210 1.00 ± .10 2,500 10,000 N/A N/A N/A
FF 1210 1.10 ± .10 2,500 10,000 N/A N/A N/A
FG 1210 1.25 ± .15 2,500 10,000 N/A N/A N/A
FH 1210 1.55 ± .15 2,000 8,000 N/A N/A N/A
FJ 1210 1.85 ± .20 2,000 8,000 N/A N/A N/A
FK 1210 2.10 ± .20 2,000 8,000 N/A N/A N/A
FL 1210 1.40 ± .15 2,000 8,000 N/A N/A N/A
FM 1210 1.70 ± .20 2,000 8,000 N/A N/A N/A
FN 1210 1.85 ± .20 2,000 8,000 N/A N/A N/A

Ceramic Surface Mount

GB 1812 1.00 ± .10 1,000 4,000 N/A N/A N/A
GC 1812 1.10 ± .10 1,000 4,000 N/A N/A N/A
GD 1812 1.25 ± .15 1,000 4,000 N/A N/A N/A
GE 1812 1.30 ± .10 1,000 4,000 N/A N/A N/A
GF 1812 1.50 ± .10 1,000 4,000 N/A N/A N/A
GG 1812 1.55 ± .10 1,000 4,000 N/A N/A N/A
GH 1812 1.40 ± .15 1,000 4,000 N/A N/A N/A
GJ 1812 1.70 ± .15 1,000 4,000 N/A N/A N/A
GK 1812 1.60 ± .20 1,000 4,000 N/A N/A N/A
GL 1812 1.90 ± .20 1,000 4,000 N/A N/A N/A
GM 1812 2.00 ± .20 1,000 4,000 N/A N/A N/A
HB 1825 1.10 ± .15 1,000 4,000 N/A N/A N/A
HC 1825 1.15 ± .15 1,000 4,000 N/A N/A N/A
HD 1825 1.30 ± .15 1,000 4,000 N/A N/A N/A
HE 1825 1.40 ± .15 1,000 4,000 N/A N/A N/A
HF 1825 1.50 ± .15 1,000 4,000 N/A N/A N/A
JB 2220 1.00 ± .15 1,000 4,000 N/A N/A N/A
JC 2220 1.10 ± .15 1,000 4,000 N/A N/A N/A
JD 2220 1.30 ± .15 1,000 4,000 N/A N/A N/A
JE 2220 1.40 ± .15 1,000 4,000 N/A N/A N/A
JF 2220 1.50 ± .15 1,000 4,000 N/A N/A N/A
KB 2225 1.00 ± .15 1,000 4,000 N/A N/A N/A
KC 2225 1.10 ± .15 1,000 4,000 N/A N/A N/A
KD 2225 1.30 ± .15 1,000 4,000 N/A N/A N/A
KE 2225 1.40 ± .15 1,000 4,000 N/A N/A N/A
This chart refers to ceramic chip thickness codes on pages 59-62.

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 63
 CERAMIC OPEN MODE CAPACITORS

FEATURES
KEMET’s Open Mode Ceramic Surface Mount Capacitor is designed to significantly minimize the probability
of a low IR or Short Circuit Condition when forced to failure in a board flex situation. This reduces the poten-
tial for causing catastrophic failures. This product is RoHS Compliant.

Applications: Markets:
• Input side filtering (power plane/bus) • Automotive
• High current applications (battery line) - All applications connected directly to the battery
• Circuits that cannot be fused to open when - Conversion to 42V power system
short circuits occur due to flex cracks • Power Conversion
- Raw power input side filtering

OUTLINE DRAWING
TIN PLATE
L
W

T B

NICKEL PLATE
S
ELECTRODES CONDUCTIVE
METALLIZATION

TABLE 1 - DIMENSIONS - MILLIMETERS (INCHES)

Metric
Metric EIAEIA
Size
Size
L - Length W - Width B - Bandwidth Separation
Size Code
Size Code Code
Code L - Length W - Width B - Bandwidth Separation
20122012 08050805 2.00 2.0
(.079) ± .20
(.079) ± .20(.008)
(.008) 1.25 (.049)
1.25 ± ±.20
(.049) 0.2(.008)
(.008) 0.50
0.50(.02)
(.02)±±.25
.25 (.010)
(.010) 0.75
0.75 (.030)
(.030)
3216 1206
3216 1206 3.20 3.2 (.126) ± .20 (.008)
(.126) ± .20 (.008) 1.601.6(.063)
(.063) ± 0.2 (.008)
± .20 (.008) 0.50 (.02) ± .25 (.010)
0.50 (.02) ± .25 (.010) N/A
N/A
3225 1210 3.2 (.126) ± .20 (.008) 2.5 (.098) ± 0.2 (.008) 0.50 (.02) ± .25 (.010) N/A
32254532
12101812
3.20 4.5
(.126) ± .20 (.008) 2.503.2(.098)
(.177) ± 0.3 (.012)
± .20 (.008)
(.126) ± 0.3 (.012)
0.50 (.02) ± .25 (.010)
0.60 (.024) ± .35 (.014)
N/A
N/A

Note: For thickness dimensions, see Table 2.

CAPACITOR ORDERING INFORMATION

OPEN-MODE INTERNAL DESIGN

The open-mode dimension (OM)

exceeds the termination bandwidth
dimensions: OM >BW

64 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 CERAMIC OPEN MODE CAPACITORS

TABLE 2
X7R DIELECTRIC CAPACITANCE RANGE AND THICKNESS TARGETS (mm)
Cap 0805 1206 1210 1812
Code 16V 25V 50V 100V 200V 16V 25V 50V 100V 200V 16V 25V 50V 100V 200V 25V 50V 100V 200V
103 DD DD DD DD DD
123 DD DD DD DD DG
153 DD DD DD DD DG
183 DD DD DD DD EC
223 DD DD DD DG EC
273 DD DD DD DG EC
333 DD DD DD DG EC
393 DD DD DD DG EC
473 DD DD DD EC EC EC EC EG GB
563 DD DD DD EC EC EC EC EG GB
683 DD DD DG EC EC EC EC EG FD GB
823 DD DD DG EC EC EC EC EG FD GB
104 DG DG DG EC EC EC EC EG FD FD FD FD FG GB GB GB GB
124 DG DG EC EC EC EC FD FD FD FD FG GB GB GB GB
154 DG DG EC EC EC EG FD FD FD FD FH GB GB GB GB
184 DG DG EC EC EC EG FD FD FD FD FH GB GB GB GB
224 DG EC EC EC FD FD FD FG FJ GB GB GB GC
274 EC EC EC FD FD FD FG GB GB GB GF
334 EG EG FD FD FD FH GB GB GB GK
394 EG EG FD FD FG FH GB GB GB GL
474 EG EG FD FD FG FJ GB GB GC
564 EG FD FD FG FO GB GB GD
684 EG FD FG FH FO GD GD GF
824 EG FD FG FJ GD GD GK
105 EG FD FH FJ GJ GJ GM
125 FG
155 FH
185 FH
225 FJ

OPEN MODE THICKNESS CODE (MM) AND REELING QUANTITIES

Thickness
Series Dimension 7" Reel Qty. 13" Reel Qty.
Code
DD 805 .90 ± .10 4000 10000
DG 805 1.25 ± .15 2500 10000

Ceramic Surface Mount

EC 1206 .90 ± .10 4000 10000
EG 1206 1.60 ± .15 2000 8000
FD 1210 .95 ± .10 4000 10000
FG 1210 1.25 ± .15 4000 10000
FH 1210 1.55 ± .15 2000 8000
FJ 1210 1.85 ± .20 2000 8000
FO 1210 2.25 ± .20 2000 8000
GB 1812 1.0 ± .10 1000 4000
GC 1812 1.1 ± .10 1000 4000
GD 1812 1.25 ± .15 1000 4000
GF 1812 1.50 ± .15 1000 4000
GK 1812 1.60 ± .20 1000 4000
GJ 1812 1.70 ± .20 1000 4000
GL 1812 1.90 ± .20 1000 4000
GM 1812 2.00 ± .20 1000 4000

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 65
 CERAMIC CHIP / HIGH VOLTAGE

KEMET's High Voltage Surface Mount Capacitors are designed to withstand high voltage applications. They
offer high capacitance with low leakage current and low ESR at high frequency. The capacitors have pure tin
(Sn) plated external electrodes for good solderability. X7R dielectrics are not designed for AC line filtering
applications. An insulating coating may be required to prevent surface arcing. These components are RoHS
compliant.
Applications Markets
• Switch Mode Power Supply • Power Supply
• Input Filter • High Voltage Power Supply
• Resonators • DC-DC Converter
• Tank Circuit • LCD Fluorescent Backlight Ballast
• Snubber Circuit • HID Lighting
• Output Filter • Telecommunications Equipment
• High Voltage Coupling • Industrial Equipment/Control
• High Voltage DC Blocking • Medical Equipment/Control
• Lighting Ballast • Computer (LAN/WAN Interface)
• Voltage Multiplier Circuits • Analog and Digital Modems
• Coupling Capacitor/CUK • Automotive

Outline Drawing

Table 1 – Dimensions - Millimeters (Inches)

Metric EIA Size Band
L - Length W - Width B - Bandwidth
Code Code Separation
2.0 (0.079) 1.2 (0.049) 0.5 (0.02
2012 0805 0.75 (0.030)
± 0.2 (0.008) ± 0.2 (0.008) ±0.25 (0.010)
3.2 (0.126) 1.6 (0.063) 0.5 (0.02)
3216 1206 N/A
± 0.2 (0.008) ± 0.2 (0.008) ± 0.25 (0.010)
3.2 (0.126) 2.5 (0.098) 0.5 (0.02)
3225 1210 N/A
± 0.2 (0.008) ± 0.2 (0.008) ± 0.25 (0.010)
4.5 (0.177) 2.0 (0.079 0.6 (0.024)
4520 1808 N/A
± 0.3 (0.012) ± 0.2 (0.008) ± 0.35 (0.014)
4.5 (0.177) 3.2 (0.126) 0.6 (0.024)
4532 1812 N/A
± 0.3 (0.012) ± 0.3 (0.012) ± 0.35 (0.014)
4.5 (0.177) 6.4 (0.250) 0.6 (0.024)
4564 1825 N/A
± 0.3 (0.012) ± 0.4 (0.016) ± 0.35 (0.014)
5.6 (0.224) 5.0 (0.197) 0.6 (0.024)
5650 2220 N/A
± 0.4 (0.016) ± 0.4 (0.016) ± 0.35 (0.014)
5.6 (0.224) 6.4 (0.250) 0.6 (0.024)
5664 2225 N/A
± 0.4 (0.016) ± 0.4 (0.016) ± 0.35 (0.014)

66 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 CERAMIC CHIP / HIGH VOLTAGE

C0G DIELECTRIC CAPACITANCE VALUES AND THICKNESS TARGETS (in.)

Series 0805 1206 1210 1808 1812 1825 2220 2225
Capac
Capacitance Max

0.050

0.050
0.065
0.065
0.065
0.065
0.101
0.101
0.101
0.101
0.080
0.080
0.080
0.080
0.080
0.080
0.067
0.067
0.067
0.067
0.067
0.067
0.067
0.067
0.067
0.067
0.067
0.067
0.067
0.067
0.067
0.067
0.067
0.067
0.067
0.067
0.067
0.067
0.067
0.067
Cap Tolerance ness
Thicknes
pF n)
(in)
*

1000

1000
Cap
ap Code/
Code/

1500

2000

1000

1500

2000

1000
1500
2000
2500
3000

1000
1500
2000
2500

3000

1000

1500

2000

2500

3000

1000
1500
2000

2500
3000

1000
1500
2000
2500

3000
500

500

500

500

500

500

500

500
Voltage
age
1.0-2.4 C,D 109-249
2.7-5.1 C,D K,M 279-519
5.6-9.1 C,D J,K,M 569-919
10 C,D J,K,M 100
11 C,D J,K,M 110
12 C,D J,K,M 120
13 C,D J,K,M 130
15 C,D G,J,K,M 150
16 C,D G,J,K,M 160
18 C,D G,J,K,M 180
20 C,D G,J,K,M 200
22 C,D G,J,K,M 220
24 C,D G,J,K,M 240
27 D,F,G,J,K,M 270
30 D,F,G,J,K,M 300
33 D,F,G,J,K,M 330
36 D,F,G,J,K,M 360
39 D,F,G,J,K,M 390
43 D,F,G,J,K,M 430
47 D,F,G,J,K,M 470
51 D,F,G,J,K,M 510
56 F,G,J,K,M 560
62 F,G,J,K,M 620
68 F,G,J,K,M 680
75 F,G,J,K,M 750
82 F,G,J,K,M 820
91 F,G,J,K,M 910
100 F,G,J,K,M 101
110 F,G,J,K,M 111
120 F,G,J,K,M 121
130 F,G,J,K,M 131
150 F,G,J,K,M 151
160 F,G,J,K,M 161
180 F,G,J,K,M 181
200 F,G,J,K,M 201
220 F,G,J,K,M 221
240 F,G,J,K,M 241
270 F,G,J,K,M 271
300 F,G,J,K,M 301
330 F,G,J,K,M 331
360 F,G,J,K,M 361
390 F,G,J,K,M 391
430 F,G,J,K,M 431
470 F,G,J,K,M 471
510 F,G,J,K,M 511

Ceramic Surface Mount

560 F,G,J,K,M 561
620 F,G,J,K,M 621
680 F,G,J,K,M 681
750 F,G,J,K,M 751
820 F,G,J,K,M 821
910 F,G,J,K,M 911
1000 F,G,J,K,M 102
1100 F,G,J,K,M 112
1200 F,G,J,K,M 122
1300 F,G,J,K,M 132
1500 F,G,J,K,M 152
1600 F,G,J,K,M 162
1800 F,G,J,K,M 182
2000 F,G,J,K,M 202
2200 F,G,J,K,M 222
2400 F,G,J,K,M 242
2700 F,G,J,K,M 272
3000 F,G,J,K,M 302
3300 F,G,J,K,M 332
3600 F,G,J,K,M 362
3900 F,G,J,K,M 392
4300 F,G,J,K,M 432
4700 F,G,J,K,M 472
5100 F,G,J,K,M 512
5600 F,G,J,K,M 562
6200 F,G,J,K,M 622
6800 F,G,J,K,M 682
7500 F,G,J,K,M 752
8200 F,G,J,K,M 822
9100 F,G,J,K,M 912
10,000 F,G,J,K,M 103

* Contact KEMET Sales Representative for C, D, F & G Capacitance Tolerance availability.

Note: Actual thickness dimensions may be less than stated maximum. Check the KEMET website, www.kemet.com, for additional values and chip sizes available.

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 67
 CERAMIC CHIP / HIGH VOLTAGE

X7R DIELECTRIC CAPACITANCE VALUES AND THICKNESS TARGETS (in.)

Series 0805 1206 1210 1808 1812 1825 2220 2225
Max

0.050

0.050

0.065

0.065

0.065

0.065

0.080

0.080

0.080

0.080

0.080

0.080

0.080

0.080
0.080
0.080
0.067
0.067
0.067
0.067

0.067

0.067

0.067

0.067
0.067

0.067

0.067

0.067

0.067

0.067

0.067

0.067

0.067

0.067

0.067

0.067

0.067

0.067

0.067

0.067
Cap Capacitance Thickness
pF Tolerance (in)
Cap Code/

1000

1000

1500

2000

1000

1500

2000

1000

1500

2000
2500
3000

1000
1500
2000

2500

3000

1000
1500

2000

2500

3000

1000

1500

2000

2500

3000

1000

1500

2000

2500

3000
500

500

500

500

500

500

500

500
Voltage
10 J,K,M 100
11 J,K,M 110
12 J,K,M 120
13 J,K,M 130
15 J,K,M 150
16 J,K,M 160
18 J,K,M 180
20 J,K,M 200
22 J,K,M 220
24 J,K,M 240
27 J,K,M 270
30 J,K,M 300
33 J,K,M 330
36 J,K,M 360
39 J,K,M 390
43 J,K,M 430
47 J,K,M 470
51 J,K,M 510
56 J,K,M 560
62 J,K,M 620
68 J,K,M 680
75 J,K,M 750
82 J,K,M 820
91 J,K,M 910
100 J,K,M 101
110 J,K,M 111
120 J,K,M 121
130 J,K,M 131
150 J,K,M 151
180 J,K,M 181
220 J,K,M 221
270 J,K,M 271
330 J,K,M 331
390 J,K,M 391
470 J,K,M 471
560 J,K,M 561
680 J,K,M 681
820 J,K,M 821
1000 J,K,M 102
1200 J,K,M 122
1500 J,K,M 152
1800 J,K,M 182
2200 J,K,M 222
2700 J,K,M 272
3300 J,K,M 332
3900 J,K,M 392
4700 J,K,M 472
5600 J,K,M 562
6800 J,K,M 682
8200 J,K,M 822
10,000 J,K,M 103
12,000 J,K,M 123
15,000 J,K,M 153
18,000 J,K,M 183
22,000 J,K,M 223
27,000 J,K,M 273
33,000 J,K,M 333
39,000 J,K,M 393
47,000 J,K,M 473
56,000 J,K,M 563
62,000 J,K,M 623
68,000 J,K,M 683
82,000 J,K,M 823
100,000 J,K,M 104
120,000 J,K,M 124
150,000 J,K,M 154
180,000 J,K,M 184
220,000 J,K,M 224

Note: Actual thickness dimensions may be less than stated maximum.

Check the KEMET website, www.kemet.com, for additional values and chip sizes available.

KEMET HIGH VOLTAGE SURFACE MOUNT CHIP (VOLTAGE CODES C,D,F,G,H, and Z)
THICKNESS AND REELING QUANTITIES
Chip size Max. Max. Tape Width Qty per Reel Qty per Reel
EIA Metric Thickness (in) Thickness (mm) (mm) 7" Plastic 13" Plastic
0805 2012 0.050 1.27 8 2,500 10,000
1206 3216 0.065 1.65 8 2,000 8,000
1210 3225 0.101 2.57 8 2,000 8,000
1808 4520 0.080 2.03 12 1,000 4,000
1812/1813 4532 0.067 1.70 12 1,000 4,000
1825 4564 0.067 1.70 12 1,000 4,000
2220 5650 0.067 1.70 12 1,000 4,000
2225 5664 0.067 1.70 12 1,000 4,000

68 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 CERAMIC CHIP / HIGH VOLTAGE

CAPACITOR ORDERING
Capacitor INFORMATION
Ordering Information
C 0805 C 102 K C R A C
Style
C - Ceramic
Chip Size
End Metallization
0805; 1206; 1210; 1808;
C = Standard
1812; 1825; 2220; 2225
Specification Failure Rate Level
C - Standard A = Not Applicable
Capacitance Code, pF Temperature Characteristic
First two digits represent significant figures. Designated by Capacitance
Third digit specifies number of zeros. 100 pF = 101. Change over Temperature Range
(Use “9” for 1.0 through 9.9 pF) G – (C0G) (±30ppm/C) (-55°C +125°C)
(Use “8” for 0.1 through .99 pF) R – X7R (±15%) (-55°C +125°C)
Capacitance Tolerance
Voltage
C = ±0.25pF* J = ±5%
C = 500V G = 2000V
D = ±0.5pF* K = ±10%
D = 1000V Z = 2500V
F = ±1%* M = ±20%
F = 1500V H = 3000V
G = ±2%*
* Contact KEMET Sales for availability.

ELECTRICAL
Electrical PARAMETERS
Parameters
Property Specification
C0G: 1 pF to 0.010 µF
Capacitance X7R: 10 pF
pf to 0.22 µF
25°C, 1.0 ± 0.2 Vrms, 1 kHz (1 MHz for ≤ 1000 pF (C0G only)
C0G: C*, D*, F*, G*, J, K, M * Contact KEMET Sales for availability.
Cap Tolerance
X7R: J, K, M
C0G: 0.1% Max
DF
X7R: 2.5% Max
Voltage Ratings 500 V, 1000 V, 1500 V, 2000 V, 2500 V, 3000 V
Operating Temperature Range From -55ºC
-55C to
to +125C
+125ºC
25ºC IR @ 500V 100 GΩ or 1000 MΩ-µF, whichever is less
125ºC IR @ 500V 10 GΩ or 100 MΩ-µF, whichever is less
-55ºC TCC X7R: + 15%
+125ºC TCC C0G: + 30 ppm / ºC
150% of Rated Voltage for Rated Voltage <1000 V
Dielectric Strength
120% of Rated Voltage for Rated Voltage >=1000V
Ripple Current Consult KEMET Sales Representative

Ceramic Surface Mount

MARKING
Marking
These chips are supplied unmarked. If required, they can be supplied LASER-marked at an extra cost.
Details on the marking format is located on page 82.
Packaging
PACKAGING
KEMET High Voltage Surface Mount MLCC are available packaged in tape and reel configuration, or bulk
bag as outlined on page 78. Please consult factory for waffle packaging options.

SOLDERING PROCESS
Soldering Process
The 0805 and 1206 case sizes are suitable for either reflow or wave soldering processes. Sizes 1210 and
larger should be limited to reflow soldering only. All sizes incorporate the standard KEMET barrier layer of
pure nickel with an overplating of pure tin (Sn) for excellent solderability and resistance to solder leaching of
the termination.
RecommendedSOLDER
RECOMMENDED Solder Pad
PADDimensions
DIMENSIONS
T (Total Length) S (Separation W (Pad Width) L (Pad Length)
Chip Size
mm in. mm in. mm in. mm in.
0805 3.30 0.130 0.70 0.028 1.60 0.063 1.30 0.051
1206 4.50 0.177 1.50 0.059 2.00 0.079 1.50 0.059
1210 4.50 0.177 1.50 0.059 2.90 0.114 1.50 0.059
1808 5.90 0.232 2.30 0.091 2.40 0.094 1.80 0.071
1812 5.90 0.232 2.30 0.091 3.70 0.146 1.80 0.071
1825 5.90 0.232 2.30 0.091 6.90 0.272 1.80 0.071
2220 7.00 0.276 3.30 0.130 5.50 0.217 1.85 0.073
2225 7.00 0.276 3.30 0.130 6.80 0.268 1.85 0.073

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 69
 CERAMIC CAPACITOR ARRAY

FEATURES
• Four individual capacitors inside • Easier to handle and solder than 4 smaller chips
one 1206 monolithic structure • Tape and reel per EIA 481-1
• Saves board and inventory space • RoHS Compliant
• One placement instead of four - less costly

CAPACITOR OUTLINE DRAWING

L
CL

BW P
BW1
P/2
W Ref

TABLE 1
EIA DIMENSIONS – MILLIMETERS (INCHES)
Size Length Width Thickness Bandwidth Bandwidth Pitch
Code L W T (max.) BW BW1 P

1632 3.2 (0.126) 1.6 (.063) 0.7 - 1.35 0.40 (0.016) 0.1 - 0.5 0.8 (0.031)
± 0.2 (0.008) ± 0.2 (.008) (0.027 - 0.053) ± 0.2 (0.008) (0.004 - 0.020) ± 0.1 (0.004)
Notes:
1. Metric is controlling - English for reference only.
2. Pitch (P) tolerances are non-cumulative along the package.
3. Thickness (T) depends on capacitance.

CERAMIC ARRAY ORDERING INFORMATION

C 1632 C 103 K 5 R A C
CERAMIC END METALLIZATION
EIA SIZE CODE C-Standard
Ceramic chip array (Tin-plated nickel barrier)
FAILURE RATE LEVEL
SPECIFICATION
A- Not Applicable
C - Standard
CAPACITANCE CODE TEMPERATURE CHARACTERISTIC
Expressed in Picofarads (pF) Designated by Capacitance
First two digits represent significant figures. Change Over Temperature Range
Third digit specifies number of zeros. (Use 9 G – C0G (NP0) (±30 PPM/°C)
for 1.0 thru 9.9pF. (Example: 2.2pF = 229 R – X7R (±15%)
VOLTAGE
CAPACITANCE TOLERANCE
5 = 50v; 3 = 25v; 4 = 16v; 8=10v
K – ±10%: M – ±20% Standard Tolerances
Contact factory for any special requirements.

70 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 CERAMIC CHIP ARRAY

TABLE 2A 1632 CERAMIC ARRAY

C0G DIELECTRIC – CAPACITANCE RANGE LAND PATTERN LAYOUT
Capacitance Capacitance 10V
Values (pF) KEMET Part Number Tolerance 16V 25V 50V 100V 200V 6 Places P X 8 Places
10 C1632C100(1)(2)GAC K,M 100 100 100 100 100
12 C1632C120(1)(2)GAC K,M 120 120 120 120 120
15 C1632C150(1)(2)GAC K,M 150 150 150 150 150
18 C1632C180(1)(2)GAC K,M 180 180 180 180 180
22 C1632C220(1)(2)GAC K,M 220 220 220 220 220
27 C1632C270(1)(2)GAC K,M 270 270 270 270 270 G C
33 C1632C330(1)(2)GAC K,M 330 330 330 330 330 Z
39 C1632C390(1)(2)GAC K,M 390 390 390 390 390
47 C1632C470(1)(2)GAC K,M 470 470 470 470 470
Y
56 C1632C560(1)(2)GAC K,M 560 560 560 560 560
68 C1632C680(1)(2)GAC K,M 680 680 680 680 680
82 C1632C820(1)(2)GAC K,M 820 820 820 820 820
100 C1632C101(1)(2)GAC K,M 101 101 101 101 Additional pad dimension information is available in
120 C1632C121(1)(2)GAC K,M 121 121 121 121 KEMET Technical Bulletin F-2100.
150 C1632C151(1)(2)GAC K,M 151 151 151 151
180 C1632C181(1)(2)GAC K,M 181 181 181 181
220 C1632C221(1)(2)GAC K,M 221 221 221
270 C1632C271(1)(2)GAC K,M 271 271 271
330 C1632C331(1)(2)GAC K,M 331 331 331
390 C1632C391(1)(2)GAC K,M 391 391 391
470 C1632C471(1)(2)GAC K,M 471 471 471
(1) To complete the KEMET part number, insert the alpha code for the tolerance desired.
K = ±10% and M = ±20% – standard tolerance. Contact factory for any special requirements. LAND PATTERN DIMENSIONS - CERAMIC CHIP
(2) To complete the KEMET part number, insert appropriate number for voltage desired:
"5" = 50 volts, "3" = 25 volts, "4" = 16 volts, and "8" = 10 volts. CAPACITOR ARRAYS - MM
Reflow Solder
Dimension Z G X Y(ref) C(ref) P(ref)
TABLE 2B 3216 2.80 0.40 0.52 1.20 1.60 0.80
X7R DIELECTRIC – CAPACITANCE RANGE Calculation Formula
Capacitance Capacitance 10V Z = Lmin + 2Jt + Tt
Values (pF) KEMET Part Number Tolerance 16V 25V 50V 100V 200V G = Smax - 2Jh -Th
X = Wmin + 2Js + Ts
330 C1632C331(1)(2)RAC K,M 331 331 331 331 331 Tt, Th, Ts = Combined
390 C1632C391(1)(2)RAC K,M 391 391 391 391 391 tolerances
470 C1632C471(1)(2)RAC K,M 471 471 471 471 471
560 C1632C561(1)(2)RAC K,M 561 561 561 561 561
680 C1632C681(1)(2)RAC K,M 681 681 681 681
820 C1632C821(1)(2)RAC K,M 821 821 821 821

Ceramic Surface Mount

1000 C1632C102(1)(2)RAC K,M 102 102 102 102
1200 C1632C122(1)(2)RAC K,M 122 122 122 122
1500 C1632C152(1)(2)RAC K,M 152 152 152 152
1800 C1632C182(1)(2)RAC K,M 182 182 182 182
2200 C1632C222(1)(2)RAC K,M 222 222 222 222
2700 C1632C272(1)(2)RAC K,M 272 272 272 272
3300 C1632C332(1)(2)RAC K,M 332 332 332 332
3900 C1632C392(1)(2)RAC K,M 392 392 392 392
4700 C1632C472(1)(2)RAC K,M 472 472 472 472
5600 C1632C562(1)(2)RAC K,M 562 562 562
6800 C1632C682(1)(2)RAC K,M 682 682 682
8200 C1632C822(1)(2)RAC K,M 822 822 822
10,000 C1632C103(1)(2)RAC K,M 103 103 103
12,000 C1632C123(1)(2)RAC K,M 123 123 123
15,000 C1632C153(1)(2)RAC K,M 153 153 153
18,000 C1632C183(1)(2)RAC K,M 183 183 183
22,000 C1632C223(1)(2)RAC K,M 223 223 223
27,000 C1632C273(1)(2)RAC K,M 273
33,000 C1632C333(1)(2)RAC K,M 333
39,000 C1632C393(1)(2)RAC K,M 393
47,000 C1632C473(1)(2)RAC K,M 473
56,000 C1632C563(1)(2)RAC K,M 563
68,000 C1632C683(1)(2)RAC K,M 683
82,000 C1632C823(1)(2)RAC K,M 823
100,000 C1632C104(1)(2)RAC K,M 104
(1) To complete the KEMET part number, insert the alpha code for the tolerance desired:
K = ±10% and M = ±20% – standard tolerances. Contact factory for any special requirements.
(2) To complete the KEMET part number, insert appropriate number for voltage desired:
"5" = 50 volts, "3" = 25 volts, "4" = 16 volts, and "8" = 10 volts.

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 71
 CERAMIC CHIP/MIL-PRF-55681

CAPACITOR OUTLINE DRAWINGS

CHIP DIMENSIONS “SOLDERGUARD I” * “SOLDERGUARD II”

SOLDER TINNED
L
W

T BW

NICKEL NICKEL

ELECTRODES SILVER ELECTRODES SILVER

METALLIZATION METALLIZATION
Military Designation - “S” or “U” Military Designation - “W” or “Y”
KEMET Designation - “H” KEMET Designation - “C”

DIMENSIONS—MILLIMETERS AND (INCHES)

KEMET
SIZE T
STYLE CODE L W MIN. MAX. BW
CDR01 C0805 2.03 ±.38 (.080 ±.015) 1.27 ±.38 (.050 ±.015) .56 (.022) 1.40 (.055) .51 ± 0.25 (.020 ±.010)
CDR02 C1805 4.57 ±.38 (.180 ±.015) 1.27 ±.38 (.050 ±.015) .56 (.022) 1.40 (.055) .51 ± 0.25 (.020 ±.010)
CDR03 C1808 4.57 ±.38 (.180 ±.015) 2.03 ±.38 (.080 ±.015) .56 (.022) 2.03 (.080) .51 ± 0.25 (.020 ±.010)
CDR04 C1812 4.57 ±.38 (.180 ±.015) 3.18 ±.38 (.125 ±.015) .56 (.022) 2.03 (.080) .51 ± 0.25 (.020 ±.010)
+.51 +.020 +.51 +.020
CDR05 C1825 4.57
–.38
( .180
–.015
) 6.35
–.38
( .250
–.015
) .51 (.020) 2.03 (.080) .51 ± 0.25 (.020 ±.010)

CDR06 C2225 5.72 ±.51 (.225 ±.020) 6.35 ±.51 (.250 ±.020) .51 (.020) 2.03 (.080) .51 ± 0.25 (.020 ±.010)
CDR31 C0805 2.00 ±.20 (.078 ±.008) 1.25 ±.20 (.049 ±.008) 1.30 (.051) .50 ± 0.20 (.020 ±.008)
CDR32 C1206 3.20 ±.20 (.125 ±.008) 1.60 ±.20 (.062 ±.008) 1.30 (.051) .50 ± 0.20 (.020 ±.008)
CDR33 C1210 3.20 ±.25 (.125 ±.010) 2.50 ±.25 (.098 ±.010) 1.50 (.059) .50 ± 0.25 (.020 ±.010)
CDR34 C1812 4.50 ±.25 (.176 ±.010) 3.20 ±.25 (.125 ±.010) 1.50 (.059) .50 ± 0.25 (.020 ±.010)
CDR35 C1825 4.50 ±.30 (.176 ±.012) 6.40 ±.30 (.250 ±.012) 1.50 (.059) .50 ± 0.30 (.020 ±.012)
Note: For Solderguard I (MIL-C55681 “S” or “U” Endmets), the length, width and thickness positive tolerances (including bandwidth) cited above are allowed to increase by the following
amounts:
Length Width/Thickness
CDR01 0.51MM (.020) 0.38MM (.015)
CDR02-06 0.64MM (.025) 0.38MM (.015)
CDR31-35 0.60MM (.023) 0.30MM (.012)

MIL-PRF-55681 PART NUMBER ORDERING INFORMATION

CDR01 B P 101 B K S M

STYLE & SIZE CODE FAILURE RATE LEVEL (%/1000 hrs.)

STYLE M — 1.0 R — 0.01
C — Ceramic P — 0.1 S — 0.001
D — Dielectric, Fixed Chip
R — Established Reliability TERMINATION FINISH
S — Solder Coated, Final W — Base Metalization—
RATED TEMPERATURE (SolderGuard I) Barrier Metal—Tinned
–55°C to +125°C U — Base Metalization— Tin or (Tin/Lead Alloy)
Barrier Metal—Solder SolderGuard II
DIELECTRICS Coated (SolderGuard I) Y — Base Metalization
P —± 30 PPM/°C—WITH OR WITHOUT VOLTAGE Barrier Metal—Tinned
X —± 15%—without voltage (100% Tin) Solderguard II
+ 15%, –25%—with voltage
CAPACITANCE TOLERANCE
CAPACITANCE
Expressed in picofarads (pF). B C D F J K M
First 2 digits represent significant figures and the last digit specifies the number of zeros to follow. ±.1 pF ±.25 pF ±.5 pF ±1% ±5% ±10% ±20%
(Use 9 for 1.0 through 9.9pF. Example: 2.2pF = 229)
RATED VOLTAGE
A — 50; B — 100

KEMET/MIL-PRF-55681 PART NUMBER EQUIVALENTS

C 0805 P 101 K 1 G M C*

CERAMIC END METALIZATION

C — SolderGuard II (Military equiv: Y, W)
SIZE CODE H — SolderGuard I (Military equiv: S, U)
See Table Above
FAILURE RATE (%/1,000 hrs.)
SPECIFICATION M — 1.0 R — 0.01
P -MIL-PRF-55681 = CDR01-CDR06 P — 0.1 S — 0.001
N-MIL-PRF-55681 = CDR31-CDR35
VOLTAGE TEMPERATURE CHARACTERISTIC
CAPACITANCE CODE Designated by Capacitance
Expressed in picofarads (pF). Change Over Temperature Range
First two digits represent significant figures. G — BP (C0G/NP0) (±30 PPM/°C)
Third digit specifies number of zeros. (Use 9 X — BX (±15% Without Voltage
for 1.0 thru 9.9 pF. Example: 2.2 pF –229) +15% -25% With Voltage)

CAPACITANCE TOLERANCE VOLTAGE

1 — 100V, 5 — 50V
B C D F J K M
±.1 pF ±.25 pF ±.5 pF ±1% ±5% ±10% ±20%

* Part Number Example: C0805P101K1GMC (14 digits - no spaces)

72 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 CERAMIC CHIP/MIL-PRF-55681
Established Reliability

RATINGS & PART NUMBER REFERENCE

CHARAC- CAP. AVAIL. MIL-PRF-55681 CHARAC- CAP. AVAIL. MIL-PRF-55681
KEMET CAPACITORS KEMET CAPACITORS
TERISTIC pF TOL. PART NUMBER TERISTIC pF TOL. PART NUMBER
100 Volt — C0805 SIZE (MILITARY CDR01) 100 Volt — C1808 SIZE (MILITARY CDR03) (Cont’d)
10 J,K C0805P100(3)1G(4)C CDR01BP100B(3)W(4) 560 J C1808P561J1G(4)C CDR03BP561BJW(4)
12 J C0805P120J1G(4)C CDR01BP120BJW(4) 680 J,K C1808P681(3)1G(4)C CDR03BP681B(3)W(4)

BP
15 J,K C0805P150(3)1G(4)C CDR01BP150B(3)W(4) 820 J C1808P821J1G(4)C CDR03BP821BJW(4)
18 J C0805P180J1G(4)C CDR01BP180BJW(4) 1,000 J,K C1808P102(3)1G(4)C CDR03BP102B(3)W(4)
22 J,K C0805P220(3)1G(4)C CDR01BP220B(3)W(4) 12,000 K C1808P123K1X(4)C CDR03BX123BKW(4)
27 J C0805P270J1G(4)C CDR01BP270BJW(4) 15,000 K,M C1808P153(3)1X(4)C CDR03BX153B(3)W(4)
BP

33 J,K C0805P330(3)1G(4)C CDR01BP330B(3)W(4) 18,000 K C1808P183K1X(4)C CDR03BX183BKW(4)

BX
39 J C0805P390J1G(4)C CDR01BP390BJW(4) 22,000 K,M C1808P223(3)1X(4)C CDR03BX223B(3)W(4)
47 J,K C0805P470(3)1G(4)C CDR01BP470B(3)W(4) 27,000 K C1808P273K1X(4)C CDR03BX273BKW(4)
56 J C0805P560J1G(4)C CDR01BP560BJW(4) 33,000 K,M C1808P333(3)1X(4)C CDR03BX333B(3)W(4)
68 J,K C0805P680(3)1G(4)C CDR01BP680B(3)W(4) 50 Volt — C1808 SIZE (MILITARY CDR03)
82 J C0805P820J1G(4)C CDR01BP820BJW(4) 39,000 K C1808P393K5X(4)C CDR03BX393AKW(4)
100 J,K C0805P101(3)1G(4)C CDR01BP101B(3)W(4) 47,000 K,M C1808P473(3)5X(4)C CDR03BX473A(3)W(4)

BX
120 J,K C0805P121(3)1(2)(4)C CDR01B(1)121B(3)W(4)
BP or

56,000 K C1808P563K5X(4)C CDR03BX563AKW(4)

BX

150 J,K C0805P151(3)1(2)(4)C CDR01B(1)151B(3)W(4) 68,000 K,M C1808P683(3)5X(4)C CDR03BX683A(3)W(4)

180 J,K C0805P181(3)1(2)(4)C CDR01B(1)181B(3)W(4) 100 Volt — C1812 SIZE (MILITARY CDR04)
220 K,M C0805P221(3)1X(4)C CDR01BX221B(3)W(4)
1,200 J C1812P122J1G(4)C CDR04BP122BJW(4)
270 K C0805P271K1X(4)C CDR01BX271BKW(4)
1,500 J,K C1812P152(3)1G(4)C CDR04BP152B(3)W(4)
330 K,M C0805P331(3)1X(4)C CDR01BX331B(3)W(4)
1,800 J C1812P182J1G(4)C CDR04BP182BJW(4)

BP
390 K C0805P391K1X(4)C CDR01BX391BKW(4)
2,200 J,K C1812P222(3)1G(4)C CDR04BP222B(3)W(4)
470 K,M C0805P471(3)1X(4)C CDR01BX471B(3)W(4)
2,700 J C1812P272J1G(4)C CDR04BP272BJW(4)
560 K C0805P561K1X(4)C CDR01BX561BKW(4)
3,300 J,K C1812P332(3)1G(4)C CDR04BP332B(3)W(4)
680 K,M C0805P681(3)1X(4)C CDR01BX681B(3)W(4)
39,000 K C1812P393K1X(4)C CDR04BX393BKW(4)
BX

820 K C0805P821K1X(4)C CDR01BX821BKW(4)

BX 47,000 K,M C1812P473(3)1X(4)C CDR04BX473B(3)W(4)
1,000 K,M C0805P102(3)1X(4)C CDR01BX102B(3)W(4)
1,200 K C0805P122K1X(4)C CDR01BX122BKW(4) 56,000 K C1812P563K1X(4)C CDR04BX563BKW(4)
1,500 K,M C0805P152(3)1X(4)C CDR01BX152B(3)W(4) 50 Volt — C1812 SIZE (MILITARY CDR04)
1,800 K C0805P182K1X(4)C CDR01BX182BKW(4) 82,000 K C1812P823K5X(4)C CDR04BX823AKW(4)
2,200 K,M C0805P222(3)1X(4)C CDR01BX222B(3)W(4) 100,000 K,M C1812P104(3)5X(4)C CDR04BX104A(3)W(4)
BX

2,700 K C0805P272K1X(4)C CDR01BX272BKW(4) 120,000 K C1812P124K5X(4)C CDR04BX124AKW(4)

3,300 K,M C0805P332(3)1X(4)C CDR01BX332B(3)W(4) 150,000 K,M C1812P154(3)5X(4)C CDR04BX154A(3)W(4)
50 Volt — C0805 SIZE (MILITARY CDR01) 180,000 K C1812P184K5X(4)C CDR04BX184AKW(4)
3,900 K C0805P392K5X(4)C CDR01BX392AKW(4) 100 Volt — C1825 SIZE (MILITARY CDR05)
BX

4,700 K,M C0805P472(3)5X(4)C CDR01BX472A(3)W(4) 3,900 J,K C1825P392(3)1G(4)C CDR05BP392B(3)W(4)

BP

100 Volt — C1805 SIZE (MILITARY CDR02) 4,700 J,K C1825P472(3)1G(4)C CDR05BP472B(3)W(4)
220 J,K C1805P221(3)1G(4)C CDR02BP221B(3)W(4) 5,600 J,K C1825P562(3)1G(4)C CDR05BP562B(3)W(4)
BP

270 J C1805P271J1G(4)C CDR02BP271BJW(4) 68,000 K,M C1825P683(3)1X(4)C CDR05BX683B(3)W(4)

3,900 K C1805P392K1X(4)C CDR02BX392BKW(4) 82,000 K C1825P823K1X(4)C CDR05BX823BKW(4)
BX

4,700 K,M C1805P472(3)1X(4)C CDR02BX472B(3)W(4) 100,000 K,M C1825P104(3)1X(4)C CDR05BX104B(3)W(4)

5,600 K C1805P562K1X(4)C CDR02BX562BKW(4) 120,000 K C1825P124K1X(4)C CDR05BX124BKW(4)
BX

6,800 K,M C1805P682(3)1X(4)C CDR02BX682B(3)W(4) 150,000 K,M C1825P154(3)1X(4)C CDR05BX154B(3)W(4)

8,200 K C1805P822K1X(4)C CDR02BX822BKW(4) 50 Volt — C1825 SIZE (MILITARY CDR05)

Ceramic Surface Mount

10,000 K,M C1805P103(3)1X(4)C CDR02BX103B(3)W(4) 220,000 K,M C1825P224(3)5X(4)C CDR05BX224A(3)W(4)
BX

50 Volt — C1805 SIZE (MILITARY CDR02) 270,000 K C1825P274K5X(4)C CDR05BX274AKW(4)

12,000 K C1805P123K5X(4)C CDR02BX123AKW(4) 330,000 K,M C1825P334(3)5X(4)C CDR05BX334A(3)W(4)
15,000 K,M C1805P153(3)5X(4)C CDR02BX153A(3)W(4) 100 Volt — C2225 SIZE (MILITARY CDR06)
BX

18,000 K C1805P183K5X(4)C CDR02BX183AKW(4) 6,800 J,K C2225P682(3)1G(4)C CDR06BP682B(3)W(4)

BP

22,000 K,M C1805P223(3)5X(4)C CDR02BX223A(3)W(4) 8,200 J,K C2225P822(3)1G(4)C CDR06BP822B(3)W(4)

100 Volt — C1808 SIZE (MILITARY CDR03) 10,000 J,K C2225P103(3)1G(4)C CDR06BP103B(3)W(4)
330 J,K C1808P331(3)1G(4)C CDR03BP331B(3)W(4) 50 Volt — C2225 SIZE (MILITARY CDR06)
BP

390 J C1808P391J1G(4)C CDR03BP391BJW(4) 390,000 K C2225P394K5X(4)C CDR06BX394AKW(4)

BX

470 J,K C1808P471(3)1G(4)C CDR03BP471B(3)W(4) 470,000 K,M C2225P474(3)5X(4)C CDR06BX474A(3)W(4)

(1) To complete Part Number for Dielectric, insert P or X symbol – as defined by Military specification.
(2) To complete Part Number for Dielectric, insert G or X symbol. (“G” for Military “BP,” or “X” for Military “BX.”)
(3) To complete Part Number, insert Capacitance Tolerance Symbol (when applicable) as available in MIL-PRF-55681: B – ±0.1 pF, C – ±0.25 pF,
D – ±0.5pF, F – ±1%, J – ±5%, K – ±10%, M – ±20%. NOTE: Available tolerances are listed in columns above.
(4) To complete Part Number, insert Failure Rate Symbol: M –1.0%; P –0.1%; R –0.01%; S –.001%.

Note: All MIL-PRF-55681 and KEMET Part Numbers tabulated above assume use of Solderguard II (MIL-PRF-55681 “W”; KEMET “C”) end metaliza-
tion. If MIL-PRF-55681 “U” or “S” (KEMET “H”) or MIL-PRF-55681 “Y” (KEMET “C”) is required, please change designators accordingly.

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 73
 CERAMIC CHIP/MIL-PRF-55681
Established Reliablility

RATINGS & PART NUMBER REFERENCE

CAP. AVAIL. MIL-PRF-55681 CAP. AVAIL. MIL-PRF-55681
KEMET CAPACITORS KEMET CAPACITORS
pF TOL. PART NUMBER pF TOL. PART NUMBER
100 Volt — BP — C0805 SIZE (MILITARY CDR31) 100 Volt — BP — C0805 SIZE (MILITARY CDR31)
1.0 B,C C0805N109(3)1G(4)C CDR31BP1R0B(3)W(4) 91 F,J,K C0805N910(3)1G(4)C CDR31BP910B(3)W(4)
1.1 B,C C0805N119(3)1G(4)C CDR31BP1R1B(3)W(4) 100 F,J,K C0805N101(3)1G(4)C CDR31BP101B(3)W(4)
1.2 B,C C0805N129(3)1G(4)C CDR31BP1R2B(3)W(4) 110 F,J,K C0805N111(3)1G(4)C CDR31BP111B(3)W(4)
1.3 B,C C0805N139(3)1G(4)C CDR31BP1R3B(3)W(4) 120 F,J,K C0805N121(3)1G(4)C CDR31BP121B(3)W(4)
1.5 B,C C0805N159(3)1G(4)C CDR31BP1R5B(3)W(4) 130 F,J,K C0805N131(3)1G(4)C CDR31BP131B(3)W(4)
1.6 B,C C0805N169(3)1G(4)C CDR31BP1R6B(3)W(4) 150 F,J,K C0805N151(3)1G(4)C CDR31BP151B(3)W(4)
1.8 B,C C0805N189(3)1G(4)C CDR31BP1R8B(3)W(4) 160 F,J,K C0805N161(3)1G(4)C CDR31BP161B(3)W(4)
2.0 B,C C0805N209(3)1G(4)C CDR31BP2R0B(3)W(4) 180 F,J,K C0805N181(3)1G(4)C CDR31BP181B(3)W(4)
2.2 B,C C0805N229(3)1G(4)C CDR31BP2R2B(3)W(4) 200 F,J,K C0805N201(3)1G(4)C CDR31BP201B(3)W(4)
2.4 B,C C0805N249(3)1G(4)C CDR31BP2R4B(3)W(4) 220 F,J,K C0805N221(3)1G(4)C CDR31BP221B(3)W(4)
2.7 B,C,D C0805N279(3)1G(4)C CDR31BP2R7B(3)W(4) 240 F,J,K C0805N241(3)1G(4)C CDR31BP241B(3)W(4)
3.0 B,C,D C0805N309(3)1G(4)C CDR31BP3R0B(3)W(4) 270 F,J,K C0805N271(3)1G(4)C CDR31BP271B(3)W(4)
3.3 B,C,D C0805N339(3)1G(4)C CDR31BP3R3B(3)W(4) 300 F,J,K C0805N301(3)1G(4)C CDR31BP301B(3)W(4)
3.6 B,C,D C0805N369(3)1G(4)C CDR31BP3R6B(3)W(4) 330 F,J,K C0805N331(3)1G(4)C CDR31BP331B(3)W(4)
3.9 B,C,D C0805N399(3)1G(4)C CDR31BP3R9B(3)W(4) 360 F,J,K C0805N361(3)1G(4)C CDR31BP361B(3)W(4)
4.3 B,C,D C0805N439(3)1G(4)C CDR31BP4R3B(3)W(4) 390 F,J,K C0805N391(3)1G(4)C CDR31BP391B(3)W(4)
4.7 B,C,D C0805N479(3)1G(4)C CDR31BP4R7B(3)W(4) 430 F,J,K C0805N431(3)1G(4)C CDR31BP431B(3)W(4)
5.1 B,C,D C0805N519(3)1G(4)C CDR31BP5R1B(3)W(4) 470 F,J,K C0805N471(3)1G(4)C CDR31BP471B(3)W(4)
5.6 B,C,D C0805N569(3)1G(4)C CDR31BP5R6B(3)W(4) 50 Volt — BP — C0805 SIZE (MILITARY CDR31)
6.2 B,C,D C0805N629(3)1G(4)C CDR31BP6R2B(3)W(4) 510 F,J,K C0805N511(3)5G(4)C CDR31BP511A(3)W(4)
6.8 B,C,D C0805N689(3)1G(4)C CDR31BP6R8B(3)W(4) 560 F,J,K C0805N561(3)5G(4)C CDR31BP561A(3)W(4)
7.5 B,C,D C0805N759(3)1G(4)C CDR31BP7R5B(3)W(4) 620 F,J,K C0805N621(3)5G(4)C CDR31BP621A(3)W(4)
8.2 B,C,D C0805N829(3)1G(4)C CDR31BP8R2B(3)W(4) 680 F,J,K C0805N681(3)5G(4)C CDR31BP681A(3)W(4)
9.1 B,C,D C0805N919(3)1G(4)C CDR31BP9R1B(3)W(4) 100 Volt — BX — C0805 SIZE (MILITARY CDR31)
10 F,J,K C0805N100(3)1G(4)C CDR31BP100B(3)W(4)
11 F,J,K C0805N110(3)1G(4)C CDR31BP110B(3)W(4) 470 K,M C0805N471(3)1X(4)C CDR31BX471B(3)W(4)
12 F,J,K C0805N120(3)1G(4)C CDR31BP120B(3)W(4) 560 K,M C0805N561(3)1X(4)C CDR31BX561B(3)W(4)
13 F,J,K C0805N130(3)1G(4)C CDR31BP130B(3)W(4) 680 K,M C0805N681(3)1X(4)C CDR31BX681B(3)W(4)
15 F,J,K C0805N150(3)1G(4)C CDR31BP150B(3)W(4) 820 K,M C0805N821(3)1X(4)C CDR31BX821B(3)W(4)
16 F,J,K C0805N160(3)1G(4)C CDR31BP160B(3)W(4) 1,000 K,M C0805N102(3)1X(4)C CDR31BX102B(3)W(4)
18 F,J,K C0805N180(3)1G(4)C CDR31BP180B(3)W(4) 1,200 K,M C0805N122(3)1X(4)C CDR31BX122B(3)W(4)
1,500 K,M C0805N152(3)1X(4)C CDR31BX152B(3)W(4)
20 F,J,K C0805N200(3)1G(4)C CDR31BP200B(3)W(4)
1,800 K,M C0805N182(3)1X(4)C CDR31BX182B(3)W(4)
22 F,J,K C0805N220(3)1G(4)C CDR31BP220B(3)W(4)
2,200 K,M C0805N222(3)1X(4)C CDR31BX222B(3)W(4)
24 F,J,K C0805N240(3)1G(4)C CDR31BP240B(3)W(4)
2,700 K,M C0805N272(3)1X(4)C CDR31BX272B(3)W(4)
27 F,J,K C0805N270(3)1G(4)C CDR31BP270B(3)W(4)
3,300 K,M C0805N332(3)1X(4)C CDR31BX332B(3)W(4)
30 F,J,K C0805N300(3)1G(4)C CDR31BP300B(3)W(4)
3,900 K,M C0805N392(3)1X(4)C CDR31BX392B(3)W(4)
33 F,J,K C0805N330(3)1G(4)C CDR31BP330B(3)W(4)
4,700 K,M C0805N472(3)1X(4)C CDR31BX472B(3)W(4)
36 F,J,K C0805N360(3)1G(4)C CDR31BP360B(3)W(4)
39 F,J,K C0805N390(3)1G(4)C CDR31BP390B(3)W(4) 50 Volt — BX — C0805 SIZE (MILITARY CDR31)
43 F,J,K C0805N430(3)1G(4)C CDR31BP430B(3)W(4) 5,600 K,M C0805N562(3)5X(4)C CDR31BX562A(3)W(4)
47 F,J,K C0805N470(3)1G(4)C CDR31BP470B(3)W(4) 6,800 K,M C0805N682(3)5X(4)C CDR31BX682A(3)W(4)
51 F,J,K C0805N510(3)1G(4)C CDR31BP510B(3)W(4) 8,200 K,M C0805N822(3)5X(4)C CDR31BX822A(3)W(4)
56 F,J,K C0805N560(3)1G(4)C CDR31BP560B(3)W(4) 10,000 K,M C0805N103(3)5X(4)C CDR31BX103A(3)W(4)
62 F,J,K C0805N620(3)1G(4)C CDR31BP620B(3)W(4) 12,000 K,M C0805N123(3)5X(4)C CDR31BX123A(3)W(4)
68 F,J,K C0805N680(3)1G(4)C CDR31BP680B(3)W(4) 15,000 K,M C0805N153(3)5X(4)C CDR31BX153A(3)W(4)
75 F,J,K C0805N750(3)1G(4)C CDR31BP750B(3)W(4) 18,000 K,M C0805N183(3)5X(4)C CDR31BX183A(3)W(4)
82 F,J,K C0805N820(3)1G(4)C CDR31BP820B(3)W(4)

(1) To complete Part Number for Dielectric, insert P or X symbol – as defined by Military specification.
(2) To complete Part Number for Dielectric, insert G or X symbol. (“G” for Military “BP,” or “X” for Military “BX.”)
(3) To complete Part Number, insert Capacitance Tolerance Symbol (when applicable) as available in MIL-PRF-55681: B – ±0.1 pF, C – ±0.25 pF.
D – ±0.5pF, F – ±1%, J – ±5%, K – ±10%, M – ±20%. NOTE: Available tolerances are listed in columns above.
(4) To complete Part Number, insert Failure Rate Symbol: M –1.0%; P –0.1%; R –0.01%; S –.001%.

Note: All MIL-PRF-55681 and KEMET Part Numbers tabulated above assume use of Solderguard II (MIL-PRF-55681 “W”; KEMET “C”) end metal-
ization. If MIL-PRF-55681 “U” or “S” (KEMET “H”) or MIL-PRF-55681 “Y” (KEMET “C”) is required, please change designators accordingly.

MARKING
See page 82 for MIL-PRF-55681 Marking

74 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 CERAMIC CHIP/MIL-PRF-55681
Established Reliability

RATINGS & PART NUMBER REFERENCE

CAP. AVAIL. MIL-PRF-55681 CAP. AVAIL. MIL-PRF-55681
KEMET CAPACITORS KEMET CAPACITORS
pF TOL. PART NUMBER pF TOL. PART NUMBER
100 Volt — BP — C1206 SIZE (MILITARY CDR32) 100 Volt — BP — C1206 SIZE (MILITARY CDR32)
1.0 B,C C1206N109(3)1G(4)C CDR32BP1R0B(3)W(4) 110 F,J,K C1206N111(3)1G(4)C CDR32BP111B(3)W(4)
1.1 B,C C1206N119(3)1G(4)C CDR32BP1R1B(3)W(4) 120 F,J,K C1206N121(3)1G(4)C CDR32BP121B(3)W(4)
1.2 B,C C1206N129(3)1G(4)C CDR32BP1R2B(3)W(4) 130 F,J,K C1206N131(3)1G(4)C CDR32BP131B(3)W(4)
1.3 B,C C1206N139(3)1G(4)C CDR32BP1R3B(3)W(4) 150 F,J,K C1206N151(3)1G(4)C CDR32BP151B(3)W(4)
1.5 B,C C1206N159(3)1G(4)C CDR32BP1R5B(3)W(4) 160 F,J,K C1206N161(3)1G(4)C CDR32BP161B(3)W(4)
1.6 B,C C1206N169(3)1G(4)C CDR32BP1R6B(3)W(4) 180 F,J,K C1206N181(3)1G(4)C CDR32BP181B(3)W(4)
1.8 B,C C1206N189(3)1G(4)C CDR32BP1R8B(3)W(4) 200 F,J,K C1206N201(3)1G(4)C CDR32BP201B(3)W(4)
2.0 B,C C1206N209(3)1G(4)C CDR32BP2R0B(3)W(4) 220 F,J,K C1206N221(3)1G(4)C CDR32BP221B(3)W(4)
2.2 B,C C1206N229(3)1G(4)C CDR32BP2R2B(3)W(4) 240 F,J,K C1206N241(3)1G(4)C CDR32BP241B(3)W(4)
2.4 B,C C1206N249(3)1G(4)C CDR32BP2R4B(3)W(4) 270 F,J,K C1206N271(3)1G(4)C CDR32BP271B(3)W(4)
2.7 B,C,D C1206N279(3)1G(4)C CDR32BP2R7B(3)W(4) 300 F,J,K C1206N301(3)1G(4)C CDR32BP301B(3)W(4)
3.0 B,C,D C1206N309(3)1G(4)C CDR32BP3R0B(3)W(4) 330 F,J,K C1206N331(3)1G(4)C CDR32BP331B(3)W(4)
3.3 B,C,D C1206N339(3)1G(4)C CDR32BP3R3B(3)W(4) 360 F,J,K C1206N361(3)1G(4)C CDR32BP361B(3)W(4)
3.6 B,C,D C1206N369(3)1G(4)C CDR32BP3R6B(3)W(4) 390 F,J,K C1206N391(3)1G(4)C CDR32BP391B(3)W(4)
3.9 B,C,D C1206N399(3)1G(4)C CDR32BP3R9B(3)W(4) 430 F,J,K C1206N431(3)1G(4)C CDR32BP431B(3)W(4)
4.3 B,C,D C1206N439(3)1G(4)C CDR32BP4R3B(3)W(4) 470 F,J,K C1206N471(3)1G(4)C CDR32BP471B(3)W(4)
4.7 B,C,D C1206N479(3)1G(4)C CDR32BP4R7B(3)W(4) 510 F,J,K C1206N511(3)1G(4)C CDR32BP511B(3)W(4)
5.1 B,C,D C1206N519(3)1G(4)C CDR32BP5R1B(3)W(4) 560 F,J,K C1206N561(3)1G(4)C CDR32BP561B(3)W(4)
5.6 B,C,D C1206N569(3)1G(4)C CDR32BP5R6B(3)W(4) 620 F,J,K C1206N621(3)1G(4)C CDR32BP621B(3)W(4)
6.2 B,C,D C1206N629(3)1G(4)C CDR32BP6R2B(3)W(4) 680 F,J,K C1206N681(3)1G(4)C CDR32BP681B(3)W(4)
6.8 B,C,D C1206N689(3)1G(4)C CDR32BP6R8B(3)W(4) 750 F,J,K C1206N751(3)1G(4)C CDR32BP751B(3)W(4)
7.5 B,C,D C1206N759(3)1G(4)C CDR32BP7R5B(3)W(4) 820 F,J,K C1206N821(3)1G(4)C CDR32BP821B(3)W(4)
8.2 B,C,D C1206N829(3)1G(4)C CDR32BP8R2B(3)W(4) 910 F,J,K C1206N911(3)1G(4)C CDR32BP911B(3)W(4)
9.1 B,C,D C1206N919(3)1G(4)C CDR32BP9R1B(3)W(4) 1,000 F,J,K C1206N102(3)1G(4)C CDR32BP102B(3)W(4)
10 F,J,K C1206N100(3)1G(4)C CDR32BP100B(3)W(4) 50 Volt — BP — C1206 SIZE (MILITARY CDR32)
11 F,J,K C1206N110(3)1G(4)C CDR32BP110B(3)W(4) 1,100 F,J,K C1206N112(3)5G(4)C CDR32BP112A(3)W(4)
12 F,J,K C1206N120(3)1G(4)C CDR32BP120B(3)W(4) 1,200 F,J,K C1206N122(3)5G(4)C CDR32BP122A(3)W(4)
13 F,J,K C1206N130(3)1G(4)C CDR32BP130B(3)W(4) 1,300 F,J,K C1206N132(3)5G(4)C CDR32BP132A(3)W(4)
15 F,J,K C1206N150(3)1G(4)C CDR32BP150B(3)W(4) 1,500 F,J,K C1206N152(3)5G(4)C CDR32BP152A(3)W(4)
16 F,J,K C1206N160(3)1G(4)C CDR32BP160B(3)W(4) 1,600 F,J,K C1206N162(3)5G(4)C CDR32BP162A(3)W(4)
18 F,J,K C1206N180(3)1G(4)C CDR32BP180B(3)W(4) 1,800 F,J,K C1206N182(3)5G(4)C CDR32BP182A(3)W(4)
20 F,J,K C1206N200(3)1G(4)C CDR32BP200B(3)W(4) 2,000 F,J,K C1206N202(3)5G(4)C CDR32BP202A(3)W(4)
22 F,J,K C1206N220(3)1G(4)C CDR32BP220B(3)W(4) 2,200 F,J,K C1206N222(3)5G(4)C CDR32BP222A(3)W(4)
24 F,J,K C1206N240(3)1G(4)C CDR32BP240B(3)W(4) 100 Volt — BX — C1206 SIZE (MILITARY CDR32)
27 F,J,K C1206N270(3)1G(4)C CDR32BP270B(3)W(4) 4,700 K,M C1206N472(3)1X(4)C CDR32BX472B(3)W(4)
30 F,J,K C1206N300(3)1G(4)C CDR32BP300B(3)W(4) 5,600 K,M C1206N562(3)1X(4)C CDR32BX562B(3)W(4)
33 F,J,K C1206N330(3)1G(4)C CDR32BP330B(3)W(4) 6,800 K,M C1206N682(3)1X(4)C CDR32BX682B(3)W(4)
36 F,J,K C1206N360(3)1G(4)C CDR32BP360B(3)W(4) 8,200 K,M C1206N822(3)1X(4)C CDR32BX822B(3)W(4)
39 F,J,K C1206N390(3)1G(4)C CDR32BP390B(3)W(4) 10,000 K,M C1206N103(3)1X(4)C CDR32BX103B(3)W(4)
43 F,J,K C1206N430(3)1G(4)C CDR32BP430B(3)W(4) 12,000 K,M C1206N123(3)1X(4)C CDR32BX123B(3)W(4)
47 F,J,K C1206N470(3)1G(4)C CDR32BP470B(3)W(4) 15,000 K,M C1206N153(3)1X(4)C CDR32BX153B(3)W(4)
51 F,J,K C1206N510(3)1G(4)C CDR32BP510B(3)W(4) 50 Volt — BX — C1206 SIZE (MILITARY CDR32)

Ceramic Surface Mount

56 F,J,K C1206N560(3)1G(4)C CDR32BP560B(3)W(4) 18,000 K,M C1206N183(3)5X(4)C CDR32BX183A(3)W(4)
62 F,J,K C1206N620(3)1G(4)C CDR32BP620B(3)W(4) 22,000 K,M C1206N223(3)5X(4)C CDR32BX223A(3)W(4)
68 F,J,K C1206N680(3)1G(4)C CDR32BP680B(3)W(4) 27,000 K,M C1206N273(3)5X(4)C CDR32BX273A(3)W(4)
75 F,J,K C1206N750(3)1G(4)C CDR32BP750B(3)W(4) 33,000 K,M C1206N333(3)5X(4)C CDR32BX333A(3)W(4)
82 F,J,K C1206N820(3)1G(4)C CDR32BP820B(3)W(4) 39,000 K,M C1206N393(3)5X(4)C CDR32BX393A(3)W(4)
91 F,J,K C1206N910(3)1G(4)C CDR32BP910B(3)W(4)
100 F,J,K C1206N101(3)1G(4)C CDR32BP101B(3)W(4)

(1) To complete Part Number for Dielectric, insert P or X symbol – as defined by Military specification.
(2) To complete Part Number for Dielectric, insert G or X symbol. (“G” for Military “BP,” or “X” for Military “BX.”)
(3) To complete Part Number, insert Capacitance Tolerance Symbol (when applicable) as available in MIL-PRF-55681: B – ±0.1 pF, C – ±0.25 pF.
D – ±0.5pF, F – ±1%, J – ±5%, K – ±10%, M – ±20%. NOTE: Available tolerances are listed in columns above.
(4) To complete Part Number, insert Failure Rate Symbol: M –1.0%; P –0.1%; R –0.01%; S –.001%.

Note: All MIL-PRF-55681 and KEMET Part Numbers tabulated above assume use of Solderguard II (MIL-PRF-55681 “W”; KEMET “C”) end metaliza-
tion. If MIL-PRF-55681 “U” or “S” (KEMET “H”) or MIL-PRF-55681 “Y” (KEMET “C”) is required, please change designators accordingly.

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 75
 CERAMIC CHIP/MIL-PRF-55681
Established Reliability

RATINGS & PART NUMBER REFERENCE

CAP. AVAIL. MIL-PRF-55681 CAP. AVAIL. MIL-PRF-55681

KEMET CAPACITORS KEMET CAPACITORS
pF TOL. PART NUMBER pF TOL. PART NUMBER
100 Volt — BP — C1210 SIZE (MILITARY CDR33) 100 Volt — BX — C1812 SIZE (MILITARY CDR34)
1,000 F,J,K C1210N102(3)1G(4)C CDR33BP102B(3)W(4) 27,000 K,M C1812N273(3)1X(4)C CDR34BX273B(3)W(4)
1,100 F,J,K C1210N112(3)1G(4)C CDR33BP112B(3)W(4) 33,000 K,M C1812N333(3)1X(4)C CDR34BX333B(3)W(4)
1,200 F,J,K C1210N122(3)1G(4)C CDR33BP122B(3)W(4) 39,000 K,M C1812N393(3)1X(4)C CDR34BX393B(3)W(4)
1,300 F,J,K C1210N132(3)1G(4)C CDR33BP132B(3)W(4) 47,000 K,M C1812N473(3)1X(4)C CDR34BX473B(3)W(4)
1,500 F,J,K C1210N152(3)1G(4)C CDR33BP152B(3)W(4) 56,000 K,M C1812N563(3)1X(4)C CDR34BX563B(3)W(4)
1,600 F,J,K C1210N162(3)1G(4)C CDR33BP162B(3)W(4) 50 Volt — BX — C1812 SIZE (MILITARY CDR34)
1,800 F,J,K C1210N182(3)1G(4)C CDR33BP182B(3)W(4) 100,000 K,M C1812N104(3)5X(4)C CDR34BX104A(3)W(4)
2,000 F,J,K C1210N202(3)1G(4)C CDR33BP202B(3)W(4) 120,000 K,M C1812N124(3)5X(4)C CDR34BX124A(3)W(4)
2,200 F,J,K C1210N222(3)1G(4)C CDR33BP222B(3)W(4) 150,000 K,M C1812N154(3)5X(4)C CDR34BX154A(3)W(4)
50 Volt — BP — C1210 SIZE (MILITARY CDR33) 180,000 K,M C1812N184(3)5X(4)C CDR34BX184A(3)W(4)
2,400 F,J,K C1210N242(3)5G(4)C CDR33BP242A(3)W(4) 100 Volt — BP — C1825 SIZE (MILITARY CDR35)
2,700 F,J,K C1210N272(3)5G(4)C CDR33BP272A(3)W(4) 4,700 F,J,K C1825N472(3)1G(4)C CDR35BP472B(3)W(4)
3,000 F,J,K C1210N302(3)5G(4)C CDR33BP302A(3)W(4) 5,100 F,J,K C1825N512(3)1G(4)C CDR35BP512B(3)W(4)
3,300 F,J,K C1210N332(3)5G(4)C CDR33BP332A(3)W(4) 5,600 F,J,K C1825N562(3)1G(4)C CDR35BP562B(3)W(4)
100 Volt — BX — C1210 SIZE (MILITARY CDR33) 6,200 F,J,K C1825N622(3)1G(4)C CDR35BP622B(3)W(4)
15,000 K,M C1210N153(3)1X(4)C CDR33BX153B(3)W(4) 6,800 F,J,K C1825N682(3)1G(4)C CDR35BP682B(3)W(4)
18,000 K,M C1210N183(3)1X(4)C CDR33BX183B(3)W(4) 7,500 F,J,K C1825N752(3)1G(4)C CDR35BP752B(3)W(4)
22,000 K,M C1210N223(3)1X(4)C CDR33BX223B(3)W(4) 8,200 F,J,K C1825N822(3)1G(4)C CDR35BP822B(3)W(4)
27,000 K,M C1210N273(3)1X(4)C CDR33BX273B(3)W(4) 9,100 F,J,K C1825N912(3)1G(4)C CDR35BP912B(3)W(4)
50 Volt — BX — C1210 SIZE (MILITARY CDR33) 10,000 F,J,K C1825N103(3)1G(4)C CDR35BP103B(3)W(4)
39,000 K,M C1210N393(3)5X(4)C CDR33BX393A(3)W(4) 50 Volt — BP — C1825 SIZE (MILITARY CDR35)
47,000 K,M C1210N473(3)5X(4)C CDR33BX473A(3)W(4) 11,000 F,J,K C1825N113(3)5G(4)C CDR35BP113A(3)W(4)
56,000 K,M C1210N563(3)5X(4)C CDR33BX563A(3)W(4) 12,000 F,J,K C1825N123(3)5G(4)C CDR35BP123A(3)W(4)
68,000 K,M C1210N683(3)5X(4)C CDR33BX683A(3)W(4) 13,000 F,J,K C1825N133(3)5G(4)C CDR35BP133A(3)W(4)
82,000 K,M C1210N823(3)5X(4)C CDR33BX823A(3)W(4) 15,000 F,J,K C1825N153(3)5G(4)C CDR35BP153A(3)W(4)
100,000 K,M C1210N104(3)5X(4)C CDR33BX104A(3)W(4) 16,000 F,J,K C1825N163(3)5G(4)C CDR35BP163A(3)W(4)
100 Volt — BP — C1812 SIZE (MILITARY CDR34) 18,000 F,J,K C1825N183(3)5G(4)C CDR35BP183A(3)W(4)
2,200 F,J,K C1812N222(3)1G(4)C CDR34BP222B(3)W(4) 20,000 F,J,K C1825N203(3)5G(4)C CDR35BP203A(3)W(4)
2,400 F,J,K C1812N242(3)1G(4)C CDR34BP242B(3)W(4) 22,000 F,J,K C1825N223(3)5G(4)C CDR35BP223A(3)W(4)
2,700 F,J,K C1812N272(3)1G(4)C CDR34BP272B(3)W(4) 100 Volt — BX — C1825 SIZE (MILITARY CDR35)
3,000 F,J,K C1812N302(3)1G(4)C CDR34BP302B(3)W(4) 56,000 K,M C1825N563(3)1X(4)C CDR35BX563B(3)W(4)
3,300 F,J,K C1812N332(3)1G(4)C CDR34BP332B(3)W(4) 68,000 K,M C1825N683(3)1X(4)C CDR35BX683B(3)W(4)
3,600 F,J,K C1812N362(3)1G(4)C CDR34BP362B(3)W(4) 82,000 K,M C1825N823(3)1X(4)C CDR35BX823B(3)W(4)
3,900 F,J,K C1812N392(3)1G(4)C CDR34BP392B(3)W(4) 100,000 K,M C1825N104(3)1X(4)C CDR35BX104B(3)W(4)
4,300 F,J,K C1812N432(3)1G(4)C CDR34BP432B(3)W(4) 120,000 K,M C1825N124(3)1X(4)C CDR35BX124B(3)W(4)
4,700 F,J,K C1812N472(3)1G(4)C CDR34BP472B(3)W(4) 150,000 K,M C1825N154(3)1X(4)C CDR35BX154B(3)W(4)
50 Volt — BP — C1812 SIZE (MILITARY CDR34) 50 Volt — BX — C1825 SIZE (MILITARY CDR35)
5,100 F,J,K C1812N512(3)5G(4)C CDR34BP512A(3)W(4) 180,000 K,M C1825N184(3)5X(4)C CDR35BX184A(3)W(4)
5,600 F,J,K C1812N562(3)5G(4)C CDR34BP562A(3)W(4) 220,000 K,M C1825N224(3)5X(4)C CDR35BX224A(3)W(4)
6,200 F,J,K C1812N622(3)5G(4)C CDR34BP622A(3)W(4) 270,000 K,M C1825N274(3)5X(4)C CDR35BX274A(3)W(4)
6,800 F,J,K C1812N682(3)5G(4)C CDR34BP682A(3)W(4) 330,000 K,M C1825N334(3)5X(4)C CDR35BX334A(3)W(4)
7,500 F,J,K C1812N752(3)5G(4)C CDR34BP752A(3)W(4) 390,000 K,M C1825N394(3)5X(4)C CDR35BX394A(3)W(4)
8,200 F,J,K C1812N822(3)5G(4)C CDR34BP822A(3)W(4) 470,000 K,M C1825N474(3)5X(4)C CDR35BX474A(3)W(4)
9,100 F,J,K C1812N912(3)5G(4)C CDR34BP912A(3)W(4)
10,000 F,J,K C1812N103(3)5G(4)C CDR34BP103A(3)W(4)
(1) To complete Part Number for Dielectric, insert P or X symbol – as defined by Military specification.
(2) To complete Part Number for Dielectric, insert G or X symbol. (“G” for Military “BP,” or “X” for Military “BX.”)
(3) To complete Part Number, insert Capacitance Tolerance Symbol (when applicable) as available in MIL-PRF-55681: B – ±0.1 pF, C – ±0.25 pF,
D – ±0.5pF, F – ±1%, J – ±5%, K – ±10%, M – ±20%. NOTE: Available tolerances are listed in columns above.
(4) To complete Part Number, insert Failure Rate Symbol: M –1.0%; P –0.1%; R –0.01%; S –.001%.

Note: All MIL-PRF-55681 and KEMET Part Numbers tabulated above assume use of Solderguard II (MIL-PRF-55681 “W”; KEMET “C”) end metal-
ization. If MIL-PRF-55681 “U” or “S” (KEMET “H”) or MIL-PRF-55681 “Y” (KEMET “C”) is required, please change designators accordingly.

MIL-PRF-55681 MAXIMUM INDIVIDUAL PACKAGING QUANTITIES

BULK - BULK -
CHIP BULK - ANTI-STATIC CHIP BULK - ANTI-STATIC
SIZE REELED STD BAG BAG SIZE REELED STD BAG BAG
C0805 2,500 25,000 10,000 C1808 2,500 7,500 3,000
C1206 2,500 25,000 10,000 C1812 1,100 7,500 3,000
C1210 2,500 25,000 10,000 C1825 1,100 7,500 1,000
C1805 2,500 7,500 3,000 C2225 1,100 5,000 1,000
MIL-PRF-55681 chips available in 7" reels only.
76 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 TANTALUM CHIP CAPACITORS
Packaging Information

Tape & Reel Packaging

KEMET’s Molded Tantalum Chip Capacitor families are

packaged in 8 mm and 12 mm plastic tape on 7" and 13"
reels, in accordance with EIA Standard 481-1: Taping of
Surface Mount Components for Automatic Handling. This
packaging system is compatible with all tape fed auto-
matic pick and place systems.
Right Hand
Orientation
Only Embossed Carrier

(+)
(–)

Embossment

8mm8mm ±.30
(0.315")
(.315or±.012")
or
12mm
12mm (0.472")
±.30 178mm
180mm (7.00")
(7.0")
Top Tape Thickness (.472 ±.012") oror
.10mm (.004") Max Thickness 330mm
330mm(13.00")
(13.0")

Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes.
Refer to EIA-556.

QUANTITIES PACKAGED PER REEL

Case Code Tape

KEMET EIA Width-mm 7" Reel* 13" Reel*
R 2012-12 8 2,500 10,000
S 3216-12 8 2,500 10,000
T 3528-12 8 2,500 10,000
U 6032-15 12 1,000 5,000
V 7343-20 12 1,000 3,000
A 3216-18 8 2,000 9,000
B 3528-21 8 2,000 8,000
C 6032-28 12 500 3,000
Packaging

D 7343-31 12 500 2,500

Y 7343-40 12 500 2,000
X 7343-43 12 500 2,000
E 7260-38 12 500 2,000
* No c-spec required for 7" reel packaging. C-7280 required for 13" reel packaging.

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 77
 CERAMIC CHIP CAPACITORS
Packaging Information

Tape & Reel Packaging KEMET offers Multilayer Ceramic Chip Capacitors
packaged in 8mm and 12mm plastic tape on 7" and
13" reels in accordance with EIA standard 481-1:
Taping of surface mount components for automatic
handling. This packaging system is compatible with all
tape fed automatic pick and place systems. See page 63
for details on reeling quantities for commercial chips
and page 76 for MIL-PRF-55681 chips.
g
handling. This packaging system is compatible with all
tape fed automatic pick and place systems. See page 63
for details on reeling quantities for commercial chips
and page 76 for MIL-PRF-55681 chips.
Anti-Static Reel
®
Embossed Carrier* Chip Orientation
T
ME 0402 and 0603 case sizes in Pocket
KE available on punched paper only. (except 1825 Commercial, and 1825 & 2225 Military)

Embossment

8mm ±.30
(.315 ±.012") Anti-Static Cover Tape
178mm (7.00") or (.10mm (.004") Max Thickness)
or 12mm ±.30
330mm (13.00") (.472 ±.012") * Punched paper carrier used for 0402 and 0603 case size.

78 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 TANTALUM & CERAMIC CHIP CAPACITORS
Packaging Information

Performance Notes
1. Cover Tape Break Force: 1.0 Kg Minimum.
2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be:
Tape Width Peel Strength
8 mm 0.1 Newton to 1.0 Newton (10g to 100g)
12 mm 0.1 Newton to 1.3 Newton (10g to 130g)
The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier
tape shall be 165 to 180 from the plane of the carrier tape. During peeling, the carrier and/or cover tape
shall be pulled at a velocity of 300 ±10 mm/minute.
3. Reel Sizes: Molded tantalum capacitors are available on either 180 mm (7") reels (standard) or 330 mm (13")
reels (with C-7280). Note that 13” reels are preferred.
4. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes.
Refer to EIA-556.
Embossed Carrier Tape Configuration: Figure 1

Table 1 — EMBOSSED TAPE DIMENSIONS (Metric will govern)

Constant Dimensions — Millimeters (Inches)
Tape Size D0 E P0 P2 T Max T1 Max
8 mm 1.5 1.75 ±0.10 4.0 ±0.10 2.0 ±0.05 0.600 0.100
and +0.10 -0.0
12 mm (0.059 (0.069 ±0.004) (0.157 ±0.004) (0.079 ±0.002) (0.024) (0.004)
+0.004, -0.0)
Variable Dimensions — Millimeters (Inches)
Tape Size Pitch B1 Max. D1 Min. F P1 R Min. T2 Max W A0B0K0
Note 1 Note 2 Note 3 Note 4
8 mm Single 4.4 1.0 3.5 ±0.05 4.0 ±0.10 25.0 2.5 8.0 ±0.30
(4 mm)
(0.173) (0.039) (0.138 ±0.002) (0.157 ±0.004) (0.984) (0.098) (.315 ±0.012)

12 mm Double 8.2 1.5 5.5 ±0.05 8.0 ±0.10 30.0 4.6 12.0 ±0.30
(8 mm) (0.323) (0.059) (0.217 ±0.002) (0.315 ±0.004) (1.181) (0.181) (0.472 ±0.012)

NOTES
1. B1 dimension is a reference dimension for tape feeder clearance only.
2. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of
Packaging

embossment location and hole location shall be applied independent of each other.
3. Tape with components shall pass around radius “R” without damage (see sketch A). The minimum trailer length (Fig. 2) may require
additional length to provide R min. for 12 mm embossed tape for reels with hub diameters approaching N min. (Table 2)
4. The cavity defined by A0, B0, and K0 shall be configured to surround the part with sufficient clearance such that the chip does not pro-
trude beyond the sealing plane of the cover tape, the chip can be removed from the cavity in a vertical direction without mechanical
restriction, rotation of the chip is limited to 20 degrees maximum in all 3 planes, and lateral movement of the chip is restricted to 0.5 mm
maximum in the pocket (not applicable to vertical clearance.)

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 79
 TANTALUM & CERAMIC CHIP CAPACITORS
Packaging Information

Embossed Carrier Tape Configuration (cont.)

Sketch D: Tape Camber (Top View)

1mm (0.039) Max.

1mm (0.039) Max.

250mm (9.843)
Allowable camber to be 1 mm/250 mm.

400mm (15.75) Min.

Figure 2:
Tape Leader
& Trailer
Dimensions
(Metric
Dimensions
Will Govern)

Figure 3: Reel Dimensions (Metric Dimensions will govern)

Table 2 – REEL DIMENSIONS (Metric will govern)
Tape Size A Max B* Min C D* Min N Min W1 W2 Max W3
8 mm 330.0 1.5 13.0 ± 0.20 20.2 50.0 8.4 14.4 7.9 Min
(12.992) (0.059) (0.512 ± 0.008) (0.795) (1.969) +1.5, -0.0 (0.567) (0.311)
See (0.331 10.9 Max
Note 3 +0.059, -0.0) (0.429)
12 mm 330.0 1.5 13.0 ± 0.20 20.2 Table 1 12.4 18.4 11.9 Min
(12.992) (0.059) (0.512 ± 0.008) (0.795) +2.0, -0.0 (0.724) (0.469)
(0.488 15.4 Max
+0.078, -0.0) (0.606)

80 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 CERAMIC CHIP CAPACITORS
Packaging Information

Punched Carrier (Paper Tape) Configuration (Ceramic Chips Only):

P0 10 pitches cumulative
tolerance on tape
T ±0.2 (±0.008)
D0 P2
E
Top
Tape
Cover A0
Bottom G F
Tape
Cover W
B0

G2
T1 P1 Center lines
Max. Cavity Size of cavity
User Direction of Feed See Note 1
Table 1

Table 1: 8 & 12mm Punched Tape

(Metric Dimensions Will Govern)
Constant Dimensions - Millimeters (Inches)
Tape D0 E P0 P2 T1 G1 G2 R Min.
Size
8mm 1.5 1.75 ±0.10 4.0 ± 0.10 2.0 ± 0.05 0.10 0.75 0.75 25 (.984)
and +0.10, -0.0 (.004) (.030) (.030) See Note 2
12mm (.059 (.069 ±0.004) (.157 ± 0.004) (.079 ± 0.002) Max. Min. Min. Table 1
+0.004, -0.0)

Table 1: 8 & 12mm Punched Tape

(Metric Dimensions Will Govern)
Variable Dimensions - Millimeters
1
(Inches)
Tape P1 W A0B0 T
F
Size
8mm 2.0 ± 0.10 1.1mm (.043)
1/2 (.079 ±.004) Max. for Paper
Pitch See Require- 3.5 ± 0.05 8.0 ± 0.3 See Note 1
Table 1 Base Tape and
ments
Section 3.3 (d) (.138 ± .002) (.315 ± 0.012) 1.6mm (.063)
Max. for Non-
8mm 4.0 ± 0.10 Paper Base
(0.157 ± .004)
Compositions.
12mm 4.0 ± 0.10 See Note 3.
(0.157 ± .004) 5.5 ± 0.05 12.0 ± 0.3
12mm 8.0 ± 0.10 (.217 ± .002) (.472 ± .012)
Double (0.315 ± .004)
Pitch
Note:
1. A0, B0 and T determined by the maximum dimensions to the ends of the terminals extending from the
body and/or the body dimensions of the component. The clearance between the ends of the terminals or
body of the component to the sides and depth of the cavity (A0, B0 and T) must be within 0.05mm (.002)
minimum and 0.50mm (.020) maximum. The clearance allowed must also prevent rotation of the component
within the cavity of not more than 20 degrees (see sketches A and B).
2. Tape with components shall pass around radius "R" without damage.
3. KEMET nominal thicknesses are: 0402 = 0.6mm and all others 0.95mm minimum.
Sketch C:
Packaging

Sketch B: Component Rotation - Top View

R Max. Component Maximum
Sketch A: (Min.) Rotation - Front 20° component rotation.
Bending Radius Cross Sectional View
See Note 2
Table 1 Typical
20° component
center line

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 81
 CERAMIC CHIP CAPACITORS
Packaging Information

Bulk Cassette Packaging (Ceramic Chips only) Table 2 – Capacitance Values Available
(Meets Dimensional Requirements IEC-286-6 and EIAJ 7201) In Bulk Cassette Packaging
Min. Max.

12.0 ± 0.1
6.8 ± 0.1
8.8 ± 0.1
Case Cap Cap
53.3*
Unit: mm
Size Dielectric Voltage Value Value
* Reference
0402 All All All All

10* 1.5 ± 0.1

0
0603 All All All All
2.0 ± 0
0.1
3.0 ± 0.2
0 0805 C0G 200 109 181
100 109 331
50 109 102

X7R 200 221 392

100 221 103

31.5 ± 0.2

36 ± 00.2
0

19.0*
50 221 273
25 221 104
16 221 104

110 ± 0.7 5.0* Y5V 25 104 224

16 104 224

Table 1 – Capacitor Dimensions for Bulk

Cassette Packaging – Millimeters
Metric EIA Minimum
Size Size Length Width Thickness Bandwidth Separation Number of
Code Code L W T B S Pcs/Cassette
1005 0402 1.0 ± 0.05 0.5 ± 0.05 0.5 ± .05 0.2 to 0.4 0.3 50,000
1608 0603 1.6 ± 0.07 0.8 ± 0.07 0.8 ± .07 0.2 to 0.5 0.7 15,000
2012 0805 2.0 ± 0.10 1.25 ± 0.10 0.6 ± .10 0.5 to 0.75 0.75 10,000
Terminations: KEMET nickel barrier layer with a tin overplate.

CAPACITOR MARKING TABLE

(Marking Optional - Not Available
for 0402 Size or Y5V Dielectric)

Alpha
Numeral Capacitance (pF) For Various Numeral Identifiers Laser marking is available as an extra-cost option for
Character 9 0 1 2 3 4 5 6 7 most KEMET ceramic chips. Such marking is two
A 0.10 1.0 10 100 1000 10,000 100,000 1,000,000 10,000,000
B 0.11 1.1 11 110 1100 11,000 110,000 1,100,000 11,000,000
sided, and includes a K to identify KEMET, followed by
C 0.12 1.2 12 120 1200 12,000 120,000 1,200,000 12,000,000 two characters (per EIA-198 - see table below) to
D 0.13 1.3 13 130 1300 13,000 130,000 1,300,000 13,000,000 identify the capacitance value. Note that marking is
E 0.15 1.5 15 150 1500 15,000 150,000 1,500,000 15,000,000
F 0.16 1.6 16 160 1600 16,000 160,000 1,600,000 16,000,000
not available for size 0402 nor for any Y5V chip. In
G 0.18 1.8 18 180 1800 18,000 180,000 1,800,000 18,000,000 addition, the 0603 marking option is limited to the K
H 0.20 2.0 20 200 2000 20,000 200,000 2,000,000 20,000,000 only.
J 0.22 2.2 22 220 2200 22,000 220,000 2,200,000 22,000,000
K 0.24 2.4 24 240 2400 24,000 240,000 2,400,000 24,000,000
L 0.27 2.7 27 270 2700 27,000 270,000 2,700,000 27,000,000
M 0.30 3.0 30 300 3000 30,000 300,000 3,000,000 30,000,000
N 0.33 3.3 33 330 3300 33,000 330,000 3,300,000 33,000,000
P 0.36 3.6 36 360 3600 36,000 360,000 3,600,000 36,000,000
Q 0.39 3.9 39 390 3900 39,000 390,000 3,900,000 39,000,000 KA3 Example shown is 1,000 pF capacitor.
R 0.43 4.3 43 430 4300 43,000 430,000 4,300,000 43,000,000
S 0.47 4.7 47 470 4700 47,000 470,000 4,700,000 47,000,000
T 0.51 5.1 51 510 5100 51,000 510,000 5,100,000 51,000,000
U 0.56 5.6 56 560 5600 56,000 560,000 5,600,000 56,000,000
V 0.62 6.2 62 620 6200 62,000 620,000 6,200,000 62,000,000
W 0.68 6.8 68 680 6800 68,000 680,000 6,800,000 68,000,000
X 0.75 7.5 75 750 7500 75,000 750,000 7,500,000 75,000,000
Y 0.82 8.2 82 820 8200 82,000 820,000 8,200,000 82,000,000
Z 0.91 9.1 91 910 9100 91,000 910,000 9,100,000 91,000,000
a 0.25 2.5 25 250 2500 25,000 250,000 2,500,000 25,000,000
b 0.35 3.5 35 350 3500 35,000 350,000 3,500,000 35,000,000
d 0.40 4.0 40 400 4000 40,000 400,000 4,000,000 40,000,000
e 0.45 4.5 45 450 4500 45,000 450,000 4,500,000 45,000,000
f 0.50 5.0 50 500 5000 50,000 500,000 5,000,000 50,000,000
m 0.60 6.0 60 600 6000 60,000 600,000 6,000,000 60,000,000
n 0.70 7.0 70 700 7000 70,000 700,000 7,000,000 70,000,000
t 0.80 8.0 80 800 8000 80,000 800,000 8,000,000 80,000,000
y 0.90 9.0 90 900 9000 90,000 900,000 9,000,000 90,000,000

82 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
 World Sales Headquarters
P.O. Box 5928 • Greenville, SC 29606 • www.kemet.com
Phone: (864) 963-6300 • Fax: (864) 963-6521

USA/Canada Locations
KEMET Electronics Corporation KEMET Electronics Corporation KEMET Electronics Canada Ltd.
2350 Mission College Blvd., Suite 972 444 Washington Street, Suite 510 105-7145 West Credit Ave., Bldg. #2
Santa Clara, CA 95054 Woburn, MA 01801 Mississauga, L5N 6J7, ON
Phone: 408-986-0424 Phone: 781-933-1010 Canada
Fax: 408-986-1442 Fax: 781-376-0929 Phone: 905-542-7930
Fax: 905-542-7949
KEMET Electronics Corporation KEMET Electronics Corporation
Schaumburg Corporate Center 8445 Freeport Parkway, Suite 320 KEMET Electronics Canada Ltd.
Suite 350, 1515 Woodfield Road Irving, TX 75063 6001 35th Avenue
Schaumburg, IL 60173 Phone: 972-870-9530 LavaL West, Quebec, Canada H7R 3P7
Phone: 847-517-1030 Fax: 972-870-9537 Phone: 450-962-0806
Fax: 847-517-1037 Fax: 450-962-6462

Europe/Africa Locations
KEMET Electronics S.A. KEMET Electronics Ltd. KEMET Electronics S.A.R.L.
1-3, Avenue de la Paix Waterfront House, 55/61 South St. ZAC Paris Rive Gauche
P.O.B. 76 Bishop’s Stortford 118-122, avenue de France
CH-1211 Geneva 20, Hertfordshire, CM23 3AL 75013 Paris, France
Switzerland United Kingdom Phone: 01-33-01-4646-1009
Phone: 41-22-715-0100 Phone: 44-1279-757201 Fax: 01-33-01-4646-1599
Fax: 41-22-715-0170 Fax: 44-1279-757188
Arrow Altech Distribution PTY LTD
KEMETElectronics GmbH Aviv Electronics Ltd. P.O. Box 701
Elisabethstrasse 89-91 Hayetzira St. No. 4 Isando, 1600
D-80797 Munich P.O. Box 2433 South Africa
Germany Ra’anana, 43100, Israel Phone: 27-11-923-9699
Phone: 49-89-456-4200 Phone: 972-9-748-3232 Fax: 27-11-923-9720
Fax: 972-9-741-6510

Asia Locations
KEMET Electronics (Shanghai) Co., Ltd. KEMET Electronics Marketing PTE Ltd. WesTech Electronics & System Co. Ltd
2/F, No. 7 Bldg., 330 Xiya Rd. 8-2-04, Sunny Point Kompleks 302/12 Central Condominum
Waigaoqiao Free Trade Zone Jalan Batu Uban, 11700 Penang Ladproa Soil, Ladproa Road
Pudong, Shanghai 200131, China Penang, Malaysia Ladyao, Jatujak
Phone: 86-21-5046-0983 Phone: 60-4-6595200 Bangkok, Thailand 109000
Fax: 86-21-5046-0981 Fax: 60-4-6595220 Phone: 662-939-3482-6
Fax: 662-939-3481
KEMET Electronics Asia Ltd. KEMET Electronics Marketing PTE Ltd.
Rm 605, Citic Bldg. 101 Thomson Road, #23-03 Crusader Electronics Pty. Ltd.
No. 19 Jian Guo Men Wai Da Jie United Square Unit 3, 92 Bryant Street
Beijing, 100004, China Singapore, 307591, Singapore Padstow, NSW 2211, Australia
Phone: 8610-8526-3628 Phone: 65-6353-6636 Phone: 612-9792-3922
Fax: 8610-8526-3626 Fax: 65-6353-6656 Fax: 612-9792-1446

KEMET Electronics Asia Ltd. KEMET Electronics Corporation Unicom International Corporation
30 Canton Rd., Room 1512 Taiwan Branch, 3-4F, No. 148, Section 4 702 Shinhwa Bldg., Mapo-Gu
Silvercord Tower II Chung-Hsaio E. Rd. Seoul, 121050, Korea
Tsimshatshui, Kowloon Bay, Hong Kong Taipei, Taiwan ROC Phone: 82-2712-5821
Phone: 852-2305-1168 Phone: 886-2-27528585 Fax: 82-2712-5823
Fax: 852-2759-0345 Fax: 886-2-27213129

NOTICE: Place 011 in front of the above Phone and Fax numbers for Europe and Asia, when dialing from a United States exchange.
Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement.
KEMET does not assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs.
© “KEMET” is a registered trademark of KEMET Electronics Corporation. © KEMET Electronics Corporation

06/04