IC-602B Image Controller
INSTALLATION MANUAL
Applied Machine: C1070P/C71hc
Product Code: A57P/A7V0
I.Confirmation Prior to Installation No. Name Shape Q’ty
1. Precautions against static electricity.
5. HDD/3
• Keep the security kit in an anti-static bag while
transporting it or storing it.
• When working in places where static electricity 1
tends to accumulate, such as on a carpet, dis-
charge electricity from your body by touching any A5XGIXC043CA
metallic portion before handling the security kit.
6. HDD installa-
2. Do not touch the contacts on the security kit with
tion plate
your hands, as that may result inpoor conductivity.
3. Do not physically damage the security kit by drop- 1
ping it, bending it, etc.
4. Take the same procedures, though the machine A5XGIXC040CA
photographs are different from the ones illus- 7. I/F cable
trated in the procedures.
Note: 1
• For the installation of the UK-104 and the
A5XGIXC004CA
UK-207, the IC-602 is required.
• When installing the UK-104, be sure to 8. Relay wiring
install it when the operation check by the harness
test print is completed after installing the IC- 1
602.
• For the installation procedures, refer to the A5XGIXC005CA
installation manuals of the UK-104 and the 9. Clamp/1
UK-207.
4
II. Accessory parts
A5XGIXC025CA
No. Name Shape Q’ty 10. Clamp/2
1. IC-602 2
1 A5XGIXC026CA
11. TP M3x4
A5A9IXC001CA
19
2. Memory
12. CD-ROM
2 each
A5XGIXC021CA
1
3. HDD/1
13. Install Manual
1 1
A5XGIXC041CA
4. HDD/2
1
After unpacking, be sure to get rid of the
A5XGIXC042CA
packaging materials and keep them out of
the reach of children.
Putting the head in the plastic bag involves
danger of suffocation.
E-1 A5XG955012
III.Installation procedure 4. Remove 7 caps, and then remove the filter cover
and the top cover/Rr. (Filter cover: 1 screw, top
1. Remove the duct cover. (3 screws)
cover/Rr: 6 screws)
Filter cover
Top cover/Rr
Caps
Duct cover
A5XGIXC045CA
2. Remove the rear cover/1 and the rear cover/2.
5. Remove the board cover.
(Rear cover/1: 4 screws, rear cover/2: 17 screws)
(1) Remove 20 screws of the board cover and pull
open the cover.
Note:
Be sure not to open the board cover at the 90
degrees angle or more.
Rear
cover/2
Board cover
Rear cover/1
A5A9IXC004CD
3. Remove the arm cover (Rr). (2 screws)
A5A9IXC007CB
(2) Unplug 1 connector and remove the wiring har-
ness from 2 clamps.
Connector
Arm cover (Rr)
A5A9IXC005CB
Clamps
A5XGIXC020CB
E-2
(3) Remove the board cover. (1 screw) 6. Remove the fan wiring harness from 7 clamps,
Note: and then remove 2 clamps A from the board
When removing the board cover, be sure to cover.
remove it opening at a 90-degree angle.
Clamps
Board cover
Fan wiring
harness
A5XGIXC009CB
Note:
Be sure to unlock the lock 1, and pull out
90°
toward the direction 2 when removing the
clamps A.
Board cover
A5A9IXC010CC
A5XGIXC011CA
7. Install 2 clamps A that are removed in the previ-
ous step to the positions shown in the picture.
Clamps A
A5XGIXC012CA
E-3
8. Install the clamps/1 to the HDD/1, the HDD/2 and 10.Install the clamps (clamp/1: 1 pc., clamp/2: 2
the HDD/3. (1 clamp each) pcs.) to the HDD installation plate.
Clamps/2
Clamp/1
Clamp/1
A5XGIXC033CA
9. Install the HDD/1, the HDD/2 and the HDD/3. (TP
screw M3x4: 15 pcs.) 11.Install the HDD installation plate. (TP screw
M3x4: 4 pcs.)
Outside of
board cover
HDD/1
HDD/2
Inside of
board cover
HDD/3
Note:
Be sure to align the numbers of the HDDs and
the numbers of the board cover when install- HDD installation
ing the HDDs. plate
A5XGIXC034CA
12.Set the fan wiring harness in the clamps.
A5XGIXC039CA
E-4
13.Connect 3 relay wiring harness connectors to (2) Connect the I/F cable connectors to each
each HDD and set the connectors in the clamps. HDD and set the connectors in the clamps.
Note:
Be sure to align the numbers of the I/F cable
connectors and the numbers of the HDDs when
installing the connectors.
Connectors
A5XGIXC032CA
14.Install the I/F cable.
(1) Set the cable so that the label "UP" comes to
the position shown in the picture.
Note: I/F cable
Be sure to set the locking section of the clamp connectors
in the direction as shown in the picture.
"UP" Locking section
of clamp
HDD installation
plate
A5XGIXC035CB
E-5
(3) Set the wiring harnesses in each clamp. 15.Install the IC-602.
Note: Note:
• Be sure to set the I/F cable to the clamps B. Be sure to align the concave part of the IC-602
• If the HDD is not added, be sure to set the and the concave part of the slot on the control-
relay wiring harness in the clamp C. ler board when installing the IC-602.
IC-602
B
A5A9IXC011CD
Align the concave
parts
IC-602
16.Replace the memory that is installed in the slot 1
to the slot 2.
A5XGIXC037CB
Slot 2 2
Slot 1
Clamp C
A5XGIXC044CA
E-6
17.Install the memories (2 pieces each) to the slot 1 (2) Set the board so that the label "FR" of the I/F
and the slot 3. cable comes to the position shown in the pic-
ture.
Memories
I/F cable
A5XGIXC024CB
Label "FR"
A5XGIXC030CA
(3) Connect 5 connectors and set the wiring har-
nesses in 3 clamps.
Note:
Be sure to connect the wiring harnesses align-
ing the numbers of the wiring harnesses and
the numbers of the board, and set the wiring
harnesses so that they are not floating.
18.Reinstall the board cover.
(1) Fix the board cover with 1 screw.
Note: Connectors
• When reinstalling the board cover, be sure
to align it with the projection.
• Be sure to reinstall the board cover outside
of the main body side.
Clamps
A5XGIXC031CB
Label "FR"
Board cover
A5A9IXC013CC
Board cover (4) Reinstall the board cover. (20 screws)
19.Reinstall the filter cover and the top cover/Rr, and
then reinstall 7 caps. (Filter cover: 1 screw, top
cover/Rr: 6 screws)
20.Reinstall the arm cover (Rr). (2 screws)
Projection
21.Reinstall the rear cover/2 (17 screws) and the
rear cover/1 (4 screws).
22.Reinstall the duct cover. (5 screws)
E-7
23. DIPSW Setting (2) Network setting initialization
Step Step
1. Turn ON the main power switch of the main body. 1. Touch the “Utility/Counter” key and then
touch the “Administrator Setting” key.
2. Enter Service Mode.
Note: 2. Touch the “Network Setting” key.
Refer to procedures in the Service Man- 3. Touch the “NIC Setting” key.
ual to enter into the Service Mode.
4. Touch the “Detail setting” key.
3. Touch the “System Setting” key and then
5. Touch the “Next” key 8 times and touch the
touch the “Software DIPSW Setting” key.
“Network Setting Clear” key.
4. Set the following DIPSW settings to ON (1).
6. Touch the “Start” key.
• 2-0: ON(1)
After the initialization, touch the “Close” key.
• 40-7: ON(1)
7. Turn the sub power switch and the main
5. Touch the “Exit [UTILITY]” key.
power switch OFF first and then turn them
24.Network connection and setup ON.
(1) Connect the network cable. Note:
Connect the network cable to the right side of By turning the sub power switch and the
the main body. main power switch OFF first and then
Note: turning them ON, the setting becomes
Be sure to use the network cable suited for the enabled.
usage environment.
(3) IP address allocation
Note:
• Usually a dedicated administrator handles
the network and PC environment at the user
end. When conducting the following setup
Network cable
procedure, always consult with proper per-
sonnel, get approval, and operate under that
person’s supervision.
• The network settings of the controller have
the DHCP function, however the initial set-
ting is OFF, so make sure to implement net-
work settings.
Step
A5A9IXC015CA 1. Touch the “Adminstrator Setting” key on the
“Utility Menu” screen.
[LED]
Both the NIC (outside) and the Machine NIC 2. 1. Touch the “Utility/Counter” key and then
(inside) have two LEDs (LED1 and LED2), each of touch the “Administrator Setting” key.
which represent the following conditions. 2. Touch the “Network Setting” key and then
touch the “NIC Setting” key. Touch the
LED 1 (top): Displays communication speed “TCP/IP Setting” key to set the following
Orange (1Gbps) items. After settings are done, touch the
Green (100Mbps) “OK” key.
OFF(10Mbps) • IP Address (IP address of the controller)
• Subnet Mask (Subnet Mask for the net-
LED 2 (bottom): Displays the link state work)
Lighting (Network is connected) • Default Gateway (IP address of the
Blinking (Data transfer state) default gateway)
OFF (Network is disconnected) 3. After the settings are done, be sure to turn
the Sub power switch and the Main power
switch OFF first and then turn them ON.
(Otherwise the settings will not be regis-
tered. When turning the Main power switch
and the Sub power switch ON, wait for more
than 10 seconds after turning them OFF
before turning them back ON.)
E-8
(4) Print a test copy to check operation
Note:
• Conduct this procedure when using the
Controller NIC.
• Output the required report.
Step
1. Turn the Main and Sub power switches ON.
2. Touch the “Controller” key on the [MACHINE]
screen.
3. Touch the “Report Type” key.
4. Select the type of report.
5. Touch the “Execute” key.
(5) Ping to check network connection.
Note:
Conduct this procedure when using the Con-
troller NIC.
Step
1. Touch the “Utility/Counter” key and then
touch the “Administrator Setting” key.
2. Touch the “Network Setting” key and then
touch the “NIC Setting” key.
3. Touch the “Detail Setting” key, and touch the
“Next” key four times.
On the [PING Confirmation] screen, touch
the “Host Name” key.
4. [Ping Send Address] screen
Enter a valid address, and touch the “OK” key.
5. Touch the “Check Connection” key.
6. Touch the “Start” key.
Check the message.
(1) If OK, <Completed normally> will appear.
(2) If there is a problem, <Error> will
appear.
=> Check if the address is correct and
the network is connected. Resend
again and make sure that the proce-
dure completes successfully.
7. Touch “Close” key and then touch “Exit” key.
E-9
