Scribd
Upload
83 views

Lab 4

This document describes a laboratory experiment on seven-segment displays. The experiment involves investigating 1-digit and 2-digit seven-segment displays, understanding code conversion, and comparing 1-digit and 2-digit displays. Students are asked to learn about seven-segment displays, draw a circuit diagram, and answer preparatory questions. The experiment involves connecting segments of 1-digit and 2-digit displays to power or ground to display numbers. Connections for common anode and common cathode 2-digit displays are explored. The conclusion compares the 1-digit display to the 2-digit displays and notes the difference between common anode and cathode configurations.

Uploaded by

Алмас Бейсебаев
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
83 views

Lab 4

This document describes a laboratory experiment on seven-segment displays. The experiment involves investigating 1-digit and 2-digit seven-segment displays, understanding code conversion, and comparing 1-digit and 2-digit displays. Students are asked to learn about seven-segment displays, draw a circuit diagram, and answer preparatory questions. The experiment involves connecting segments of 1-digit and 2-digit displays to power or ground to display numbers. Connections for common anode and common cathode 2-digit displays are explored. The conclusion compares the 1-digit display to the 2-digit displays and notes the difference between common anode and cathode configurations.

Uploaded by

Алмас Бейсебаев
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

JSC “Kazakh-British Technical University”

Faculty of Information Technology


Electrical Engineering and Computer Science Department

Electronics and Digital Design


Laboratory Work №4

Prepared by: Beisebaev Almas


Accepted by: Bulganbayev Muratbek

Almaty, 2023
SEVEN-SEGMENT DISPLAYS
Aims: investigate 1-digit and 2-digit seven-segment displays operation, understand the process of
code conversion for the device, and make a comparison between 1 and 2 digit sevensegment
displays.

PREPARATION TO LAB WORK.


1 Learn the information about seven-segment displays
2 Consider scheme of experiment 4A and draw it using Scheme Design System.
3 Answer the questions below in written form.
3.1 What is an order to count pins of a chip?
The pins on an IC are numbered counterclockwise, starting with the upper-left pin
closest to the clocking mark
3.2 What is a code conversion?
The method or technique used to convert code from one format to another is
termed code conversion.
3.3 What is a BCD-to-seven-segment decoder?
A seven-segment decoder is a logic circuit often used for the visual display of digital
information
3.4 What is the way to obtain #6 (or 2, or3 and so on) on the display?
A, C, D, E, F, G
3.5 Show the situation of segments from a to g on the display. 3.9
3.6 If we apply +5V to segments b and c we can see #1 on the display.
3.7 How many pins has the chip of seven-segment display got? 10 pins
3.8 What shall we do with pins #3, 5, 8? Ground
3.9 Show seven-segment display internal structure with LEDs.

3.10 What is another name of a seven-segment display? Seven-segment indicator


3.11 What is the difference between conversion and coding of a decimal number?
Binary-coded decimal (English binary-coded decimal), BCD, 8421-BCD - a form of
writing rational numbers, when each decimal digit of a number is written as its
four-bit binary code.
3.12 Show the differences between 1- and 2-digit seven-segment display.
More pins in 2 digit

Experiment 4A. Realize the following circuit on a breadboard. Connecting Va, Vb, Vc, Vd, Ve,
Vf and Vg inputs to either GND or VCC based on the following table, fill in the blanks.
Va Vb Vc Vd Ve Vf Vg Display
1 5V 5V 5V 5V 5V 5V 0V 0
2 0V 5V 5V 0V 0V 0V 0V 1
3 5V 5V 0V 5V 5V 0V 5V 2
4 5V 5V 5V 5V 0V 0V 5V 3
5 0V 5V 5V 0V 0V 5V 5V 4
6 5V 0V 5V 5V 0V 5V 5V 5
7 5V 0V 5V 5V 5V 5V 5V 6
8 5V 5V 5V 0V 0V 0V 0V 7
9 5V 5V 5V 5V 5V 5V 5V 8
10 5V 5V 5V 0V 0V 5V 5V 9
11 5V 0V 5V 5V 0V 5V 5V 5
12 0V 5V 5V 5V 5V 0V 5V D
13 0V 5V 5V 5V 5V 0V 5V D

Experiment 4B. Use 2-digit seven- segment display. Situate it on the breadboard. Pins 13 and 14
are connected to GND. Define which pin corresponds to which segment, show them in the picture.
Fill in the table, showing the voltage for the numbers obtained. For example, V 1 is a voltage,
applied to pin 1 and so on. Use resistors of 330(220)Ω to avoid the LED’s burning.

# V1 V2 V3 V4 V5 V6 V7 V8 V9 V10 V11 V12 V15 V16 V17 V18 #


1 0V 5V 5V 0V 0 V 0V 0V 0V 5V 0V 5V 5V 0V 5V 5V 0V 15
2 5 5 0 5 5 0 5 0 0 5 5 0 0 5 5 0 24
3 5 5 5 5 0 0 5 0 5 5 5 0 0 0 0 0 37
4 5 0 5 5 5 5 5 0 5 5 5 5 5 5 0 0 60
5 5 5 5 5 5 5 5 0 5 5 5 5 0 5 5 0 89
6 0 5 5 0 0 5 5 0 0 5 5 0 0 0 0 0 41
7 5 0 5 5 0 5 5 0 5 5 0 5 5 0 5 0 52
8 5 5 5 0 0 0 0 0 5 5 5 5 0 0 5 0 73
9 5 5 5 5 0 5 5 0 5 0 5 5 5 5 5 0 96
10 5 5 5 5 5 5 0 0 5 5 5 5 5 5 5 0 08

Experiment 4C. Use another type of 2-digit seven segment display (common anode). Make
appropriate connections and fill in the table.

# V1 V2 V3 V4 V5 V6 V7 V8 V9 V10 V11 V12 V15 V16 V17 V18 #


1 5 0 0 5 5 5 5 0 0 5 0 0 5 0 0 0 15
2 0 0 5 0 0 5 0 0 5 0 0 5 5 0 0 0 24
3 0 0 0 0 5 5 0 0 0 0 0 5 5 5 5 0 37
4 0 5 0 0 0 0 0 0 0 0 0 0 0 0 5 0 60
5 0 0 0 0 0 0 0 0 0 0 0 0 5 0 0 0 89
6 5 0 0 5 5 0 0 0 5 0 0 5 5 5 5 0 41
7 0 5 0 0 5 0 0 0 0 0 5 0 0 5 0 0 52
8 0 0 0 5 5 5 5 0 0 0 0 0 5 5 0 0 73
9 0 0 0 0 5 0 0 0 0 5 0 0 0 0 0 0 96
10 0 0 0 0 0 0 5 0 0 0 0 0 0 0 0 0 08
TEST QUESTIONS

1С 2C 3B 4B 5A 6E 7C 8D 9E 10E

Conclusion
In this laboratory work, we used a seven-segment screen connecting it to the current sources and
to ground via a key. We also used a resistor to prevent the screen from burning out. Then we used
a double seven-segment screen with 16 inputs cathode version as well as anode version. The
difference is that the anode version is like NOT Gate.

You might also like