Scribd
Upload
67 views

Switch

The document provides help output for configuration commands on a network switch. It begins by listing the top-level configuration commands that can be used, including commands to configure interfaces, IP settings, MAC address tables, EtherChannel, spanning tree, usernames, VLANs and VTP. It then provides help for configuring an interface, including settings for switchport mode, CDP, spanning tree and other interface-level options. Finally, it lists top-level EXEC commands that can be run from privileged EXEC mode, such as commands to reset functions, manage the clock, copy files, debug issues and show information.

Uploaded by

samar
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
67 views

Switch

The document provides help output for configuration commands on a network switch. It begins by listing the top-level configuration commands that can be used, including commands to configure interfaces, IP settings, MAC address tables, EtherChannel, spanning tree, usernames, VLANs and VTP. It then provides help for configuring an interface, including settings for switchport mode, CDP, spanning tree and other interface-level options. Finally, it lists top-level EXEC commands that can be run from privileged EXEC mode, such as commands to reset functions, manage the clock, copy files, debug issues and show information.

Uploaded by

samar
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

Switch(config)#?

Configure commands: banner boot cdp clock do enable end exit hostname interface ip line Define a login banner Boot Commands Global CDP configuration subcommands Configure time-of-day clock To run exec commands in config mode Modify enable password parameters Exit from configure mode Exit from configure mode Set system's network name Select an interface to configure Global IP configuration subcommands Configure a terminal line

mac-address-table Configure the MAC address table no Negate a command or set its defaults EtherChannel configuration Modify use of network based services Spanning Tree Subsystem Establish User Name Authentication Vlan commands Configure global VTP state

port-channel service

spanning-tree username vlan vtp

Switch(config)#int fa0/1
Switch(config-if)#switchport ? access mode native Set access mode characteristics of the interface Set trunking mode of the interface Set trunking native characteristics when interface is in trunking mode

nonegotiate Device will not engage in negotiation protocol on this interface port-security Security related command trunk voice Set trunking characteristics of the interface Voice appliance attributes

Switch(config-if)#switchport mode ?
access Set trunking mode to ACCESS unconditionally dynamic Set trunking mode to dynamically negotiate access or trunk mode trunk Set trunking mode to TRUNK unconditionally

Switch(config-if)#switchport mode ?
access Set trunking mode to ACCESS unconditionally dynamic Set trunking mode to dynamically negotiate access or trunk mode trunk Set trunking mode to TRUNK unconditionally

Switch(config-if)#?
cdp Global CDP configuration subcommands Etherchannel/port bundling configuration

channel-group

channel-protocol Select the channel protocol (LACP, PAgP) description duplex exit Interface specific description Configure duplex operation. Exit from interface configuration mode Manually set interface MAC address

mac-address no shutdown spanning-tree speed

Negate a command or set its defaults Shutdown the selected interface Spanning Tree Subsystem

Configure speed operation.

switchport

Set switching mode characteristics

Switch(config-if)#cdp ?
enable Enable CDP on interface

Switch(config-if)#spanning-tree ?
guard Change an interface's spanning tree guard mode

link-type Specify a link type for spanning tree protocol use portfast Enable an interface to move directly to forwarding on link up vlan VLAN Switch Spanning Tree

Switch#?
Exec commands: <1-99> clear clock Session number to resume Reset functions Manage the system clock

configure Enter configuration mode connect copy debug delete dir disable Open a terminal connection Copy from one file to another Debugging functions (see also 'undebug') Delete a file List files on a filesystem Turn off privileged commands

disconnect Disconnect an existing network connection enable erase exit logout Turn on privileged commands Erase a filesystem Exit from the EXEC Exit from the EXEC

more no ping reload resume setup show telnet

Display the contents of a file Disable debugging informations Send echo messages Halt and perform a cold restart Resume an active network connection Run the SETUP command facility Show running system information Open a telnet connection

terminal Set terminal line parameters traceroute Trace route to destination undebug vlan write Disable debugging functions (see also 'debug')

Configure VLAN parameters Write running configuration to memory, network, or terminal

You might also like