NA101
Car Audio System Player
INSTRUCTION MANUAL
CD MP3 WMA USB AUX-IN
1A USB Universal Charge
Safety
WARNING Note: This quipment has been tested and found to comply with the
Stop the car before operating the unit. limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
Important to know... generates uses and can radiate radio frequency energy and, if not
To prevent a short circuit, never put or leave any metallic objects installed and used in accordance with the instructions, may cause
(such as coins or metal tools) inside the unit. harmful interference to radio communications. However, there is no
Caution: Adjust the volume so that you can hear sounds guarantee that interference will not occur in a particular installation.
outside the car. Driving with the volume too high may cause an If this equipment does cause harmful interference to radio or
accident. television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
Condensation: When the car is air-conditioned, moisture may interference by one or more of the following measures:
collect on the laser lens. This may cause disc read errors. In this case, Reorient or relocate the receiving antenna.
remove the disc and wait for the moisture to evaporate. Increase the separation between the equipment and receiver.
The illustrations in this manual are examples used to explain more Connect the equipment into an outlet on a circuit different from
clearly how the controls are used. Therefore, what appears on the that to which the receiver is connected.
illustrations may differ from what appears on the actual Consult the dealer or an experienced radio technician for help.
equipment.
If you experience problems during installation, consult your FCC Radiation Exposure Statement
Nakamichi dealer. This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This equipment should be
When you purchase external components, check with your installed and operated with minimum distance 20 cm between the
Nakamichi dealer to make sure that they work with your model and radiator & your body.
in your area.
Maintenance
Cleaning the unit: Wipe off the dirt on the panel with a dry silicon or
soft cloth. Failure to observe this precaution may result in damage to
the monitor or unit.
Cleaning the connector: Wipe off dirt on the connector of the unit and
faceplate. Use a cotton swab or cloth.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
EN 1
Preparation What’s in the box
How to attach/detach the faceplate Check and identify the contents of your package:
Attach Detach
1 1 Main unit Front panel Trim plate
(with sleeve)
2
2
Do not expose the faceplate to direct sunlight, excessive heat, or
humidity. Also avoid places with too much dust or the possibility of
water splashing. Carrying case Remote ISO male
Keep the faceplate in its casing while detached. (for front panel) control connector
The faceplate is a precision piece of equipment and can be
damaged by shocks or jolts.
To prevent deterioration, do not touch the terminals of the unit and
faceplate with your fingers. Disassembly tool Screw x 4pcs User manual
(2pcs)
How to reset your unit
1 3
2
Reset
If this unit fails to operate properly, press the reset button.
The unit returns to factory settings when the reset button is pressed.
2 EN
Installation / Connection
Basic Procedure Caution
1 Remove the key from the ignition switch, then disconnect If your car’s ignition does not have an ACC position, connect the ignition
wires to a power source that can be turned on and off with the ignition key. If
the terminal of the car battery. you connect the ignition wire to a power source with a constant voltage
2 Make proper input and output wire connections. supply, as with battery wires, the battery may die.
Install this unit in the console of your vehicle. Make sure the faceplate will
3 Install the unit to your car. not hit the lid of the console (if any) when closing and opening.
4 Reconnect the terminal of the car battery. After the unit is installed, check whether the brake lamps, blinkers, wipers,
etc. on the car are working properly.
5 Reset the unit. Mount the unit so that the mounting angle is 30° or less.
If the fuse blows, first make sure the wires are not touching to cause a short
Warning circuit, then replace the old fuse with one that has the same rating.
The unit can only be installed in a car with a 12 V DC power supply, negative Connect the speaker wires correctly to the terminals to which they
ground. correspond. The unit may be damaged or fail to work if you share
If you connect the ignition wire (red) and the battery wire (yellow) to the car the wires or ground them to any metal part in the car.
chassis (ground), you may cause a short circuit, that in turn may start a fire.
Always connect those wires to the power source running through the fuse box. When only two speakers are being connected to the system, connect the
connectors either to both the front output terminals or to both the rear
Disconnect the battery’s negative terminal and make all electrical output terminals (do not mix front and rear).
connections before installing the unit.
Mounting and wiring this product requires skills and experience. For
Insulate unconnected wires with vinyl tape or other similar material. To safety’s sake, leave this work to professionals.
prevent a short circuit, do not remove the caps on the ends of the If you experience problems during installation, consult your Nakamichi
unconnected wires or the terminals. dealer.
Be sure to ground this unit to the car’s chassis again after installation.
If the power is not turned ON, the speaker wire may have a short-circuit or
touched the chassis of the vehicle and the protection function may have
been activated. Therefore, the speaker wire should be checked.
Wiring Connection
FM/AM Antenna Socket
Rear RCA Output (Left) L
Rear RCA Output (Right) R
REAR
Antenna Jack(not included)
ISO Connector
1 3 5 7
B
2 4 6 8
5 7
A 4 8
ISO Connector Wiring Chart
Pin Color and function Pin Color and function
A4 Yellow Battery(+) B1/B2 Violet + / Violet/Black Right rear speaker
A5 Blue Connect to system control terminal B3/B4 Grey + / Grey/Black Right front speaker
of the power AMP or auto antenna
relaycontrol terminal(Max 150MA 12VDC)
A7 Red Ignition(ACC) B5/B6 White + / White/Black Left front speaker
A8 Black Ground B7/B8 Green + / Green/Black Left rear speaker
EN 3
Installing the unit
1
3
Sleeve Bend the appropriate
2
tabs to hold the sleeve
1
Trim plate firmly in place.
Control panel
2 Before attaching, make 18
2m
m
sure the direction of the
1 53
escutcheon is correct. mm
(Wider hooks on the Dashboard
bottom side.) 2
Screw
( not included in this packing )
3 Sleeve
4
Trim plate
Control panel
Removing the unit
1 Detach the control panel. Disassembly
2 Engage the catch pin on the removal tools into the holes on Trim plate
both sides of the escutcheon, then pull it out.
3 Insert the disassembly tools deeply into the slots on each Sleeve
side, then follow the arrows instructions as shown on the 3
right.
1 2
Disassembly
Control panel
4 EN
Basic Operation
Encoder Volume Knob Loading slot Ejects the disc
DBSS
XBASS BAND
SRC EQ
MENU
1 2 3 4 5 6 AUX IN
Detaches the Power / Mute Display window
control panel Push open the cover
USB terminal
Aux-In jack
When you press or hold the following button(s)...
Main unit General operation
SRC Select the available sources (Radio, Disc, USB , Aux-In ), if the power is turned on.
Rotatory Rotate it to increase or decrease the volume.
Volume knob Select items.
■ Turn mute or restore volume.
■ Turn the unit on. Press and hold again to turn the unit off.
Power / Mute ■ Confirms selection.
■ Select the FM bands (FM1/ FM2/ FM3) or AM1 (MW1) / AM2 (MW2)
BAND ■ Under media playback to access into search mode.
■ Press and hold to activate the Auto Store function.
1 Pause/resume playback of a Disc, USB.
■ Under Radio mode to enter into the Auto Seek mode, press and hold to enter into the Manual Seek mode.
■ Under Media playback mode to skip track / file, press and hold to fast forward / backward.
MENU To access into the Audio Menu mode, press and hold to enter into the System Menu mode.
DBSS Press to turn On or Off dynamic bass boost sound.
■ To view the Clock.
■ Under Media playback mode to view play informations.
XBASS Turn On or Off the Xbass bosster function.
EQ To adjust the EQ (Preset Equalizer) setting.
Returns to the previous item.
EN 5
Function Settings
1 Press MENU to access into the [AUDIO MENU] mode, press and hold to enter into the [MENU] mode.
2 Press repeatedly to select the item to be adjusted.
3 Turn the encoder volume knob to select a value / option.
[AUDIO MENU]...
Item Selectable Setting
BASS ADJUST
BASS LEVEL Adjust the level -7 to +7.
TREBLE ADJUST
TREBLE LEVEL Adjust the level -7 to +7.
BALANCE Adjust the balance between the right and left speakers from 12R (full right) to
12L (full left).
FADER Adjust the fader between the front and rear speakers from 12R (full rear) to
12L (full front).
[MENU]...
Item Selectable Setting
CLOCK
CLOCK SET Adjust the Hours and Minutes
CLOCK FORMAT Select the time format 12H or 24H
BEEP TONE Turn On or Off this beep sound
DIMMER Adjust the LCD display backlight level between Hight or Low
6 EN
Listening to the Radio
XBASS
DBSS
BAND
SRC EQ
MENU
1 2 3 4 5 6 AUX IN
■ Hold for about 2 seconds to memorize the current station .
■ Press briefly to recall memorized station.
1 Press BAND repeatedly to a band ( FM1, FM2, FM3, AM1(MW1) or AM2 (Mw2)).
2 Press to search for a station.
Adjust [MENU] mode settings
While listening to the radio...
1 Press and hold MENU to enter into the [MENU] mode.
2 Press repeatedly to select the item to be adjusted.
3 Turn the encoder volume knob to select a value / option.
Item Selectable Setting
Press the to access into Auto Store mode, the six strongest stations of the selected band
AUTO STORE
are saved in preset channel automatically: FM1, FM2, FM3(1-6), AM1, AM2.
Select suitable country region of the radio: USA; LATIN; EUROPE; RUSSIA(Oirt); M-EAST; ASIA; JAPAN;
AREA AUST (Australia)
To receive more radio stations or only stations with strong signal, you can adjust the radio
LOCAL SEEK
sensitivity.
EN 7
Listening to a Disc/ USB device
Detaches the ■ Press to select a track / file. ■ Press to repeat one track, press again to repeat all tracks.
control panel ■ Press and hold for fast forward / backward. ■ Press and hold repeat a folder.
Ejects
the disc
XBASS DBSS
BAND
SRC EQ
USB
terminal
MENU
1 2 3 4 5 6 AUX IN
Press into search mode Press to pause. Press again to resume playback. Press to move next/previous folder.
■ Press to start random play, press again to cancel random play.
■ Press and hold random a folder.
Playing a disc
Insert the disc into the Disc Slot with label side facing up, the MTP( Media Transfer Protocol) in Android
unit will play starts automatically. This model supports Android MTP function, You can use the
system to play the audio input from your Android phone.
Playing a USB device 1 Slide the USB socket cover market to the left.
1 Slide the USB socket cover market to the left. 2 Insert the Android Phone device into the USB socket.
2 Insert the USB device into the USB socket.
3 Press the SRC to select USB mode.
3 Press the SRC to select USB mode.The unit starts playing
from the USB device automatically. 4 The unit starts playing from the Android Phone.
Remark:
This function only supports part of the Android Phone.
Listening to the other external components
USB Smart Phone 1A charging XBASS
BAND
DBS S
SRC EQ
1 Slide the USB socket to left. MENU
1 2 3 4 5 6 AUX IN
2 Insert the iPhone or Smart Phone device into the USB socket.
3 Once the iPhone or Smart Phone is connected and recognized,
the iPhone/Smart Phone begins to charge.
Auxiliary input jack
3.5 mm Cable (not included)
1 Press the SRC to select AUX-IN mode.
2 Turn on the external component and start playing.
8 EN
Remote Control Operation
SRC AUDIO
When you press or hold the following button(s)...
Main unit General operation
Turn mute or restore volume.
Press turn the unit on or off.
Press increas the volume.
Press decreas the volume.
■ Under Radio mode to enter into the Auto Seek mode, press and hold to enter into the Manual Seek
mode.
■ Under Media playback mode to skip track / file, press and hold to fast forward / backward.
SRC Selects the available sources (Radio, Disc, USB or Aux-In ), if the power is turned on.
AUDIO Press to access into the Audio Menu mode.
EN 9
Product Information
General About Audio file
Power Supply: 12V DC (10.5-14.4V), negative ground ■ USB or memory file system: FAT16, FAT32
Fuse: 15A ■
MP3/WMA bit rate: 32-320kbps and varible bit rate
Suitable Speaker Impedance: 4 -8 ■ MP3 sampling frequencies: 8-48kHz
Aux-In level: 500mV ■ WMA sampling frequencies: 32kHz, 44.1kHz, 48kHz
■ ID3 tag v1.0 or later
Audio Section
Maximum Power Output: 50W x 4 Channels
Continous Power Output: 20W x 4 RMS
USB Smart Phone 1A charging
Pre-AMP Output Voltage: 1.5 V Output Voltage : 5 V DC
Output Current : 1000 mA (1A)
FM tuner section
Frequency Range: 87.5 -107.9MHz (USA)
87.5 - 108MHz (ASIA)
87.5 - 108MHz (Europe)
Usable Sensitivity: Better than 8dB at S/N 30dB
AM tuner section
Frequency Range: 530 - 1710KHz (USA)
522 - 1620KHz (ASIA)
522 - 1620KHz (Europe)
Usable Sensitivity: Better than 40dB at S/N 20dB
USB devices
USB Flash Memory: USB 1.1 & 2.0 Compatible
10 EN
www.nakamichicaraudio.com
