Electrical Interface

EUROMAP 67 between Injection Moulding Machine

and Handling Device / Robot

Version 1.0, February 2003

(10 pages)

This recommendation was prepared by the Technical Commission of EUROMAP.

EUROMAP 67 Version 1.0

Content Page

1 Scope and Application ............................................................................ 3

2 Description ............................................................................................... 3
2.1 Plug and socket outlet ................................................................................................ 3
2.2 Switch contact specification ...................................................................................... 4
2.2.1 Emergency stop, safety devices and mould area free
2.2.2 Digital inputs
2.2.3 Digital outputs
2.2.4 Reference Potential

2.3 Plug contact assignment............................................................................................ 4

2.3.1 Table 1: Injection moulding machine signals.............................................................................. 4
2.3.2 Table 2: Handling device / robot signals .................................................................................... 6

3 Ejector sequences ................................................................................... 7

4 Core puller sequences ............................................................................ 7

4.1 Core puller 1 ................................................................................................................ 7
4.1.1 Core puller 1 ejector sequence .................................................................................................. 7
4.1.2 Core puller 1 sequence for part removal ................................................................................... 7
4.1.3 Core puller 1 sequence for insertion .......................................................................................... 7
4.1.4 Core puller 1 sequence for part removal and insertion .............................................................. 8

4.2 Core puller 2 ................................................................................................................ 8

4.2.1 Core puller 2 ejector sequence ................................................................................................. 8
4.2.2 Core puller 2 sequence for part removal .................................................................................... 8
4.2.3 Core puller 2 sequence for insertion .......................................................................................... 8
4.2.4 Core puller 2 sequence for part removal and insertion .............................................................. 9

5 Handling device / robot power supply ................................................... 9

6 Sources of supply.................................................................................... 9

EUROMAP 67 Page 2 of 10
EUROMAP 67 Version 1.0

1 Scope and Application

This EUROMAP recommendation defines the connection between the injection moulding machine and the
handling device / robot. This is intended to provide interchangeability. EUROMAP 67 shall generally be applied
six month after publication.

In addition recommendations are given for signal voltage and current levels. The mains connection of the
handling device / robot is also specified.

Please note that the risk assessment for the movements of the handling device / robot mostly require
redundancy which is achieved by two channels on Table1: ZA3, ZC3 and ZA4, ZC4 on the injection moulding
machine. EUROMAP 12 shall therefore only be applied for replacement purposes on existing equipment .

2 Description
The signals in both the injection moulding machine and the handling device / robot are given by contacts, e.g.
contacts of relays or switches, semiconductors, etc. The contact making is either potential-free or related to a
reference potential supplied to a contact of the plug mounted on the injection moulding machine or the handling
device / robot (see Tables 1 and 2). All signals which are not optional shall be supported by all injection
moulding machines and handling devices / robots.

2.1 Plug and socket outlet

The connection between the injection moulding machine and the handling device / robot is achieved by the
plugs specified below. For the injection moulding machine (see Figure 2) and the handling device / robot (see
Figure 1) the plug contacts should be capable of taking a minimum of 250 V and 10 A.

Arrangements of pins and sockets viewed from the mating side (Opposite the wiring side)

Figure 1 = Plug on the handling device Figure 2 = Plug on the injection moulding machine

EUROMAP 67 Page 3 of 10
EUROMAP 67 Version 1.0

2.2 Contact specification

2.2.1 Emergency stop, safety devices, mould area free

- The voltages of the signals must not exceed 50 V DC or 250 V AC.

- A current of at least 6 mA must be maintained during signalling

- The maximum current is 6A

2.2.2 Logical Signals

- These signals shall be in accordance with clause 3.3.1 of EN 61131-2, Table 9, Type 2 or with clause 3.3.3
of EN 61131-2,Table 11, 0,1 A max

2.2.3 Reference potential (Table 1: ZA9, ZC9 and Table 2: A9, C9)
- Voltage 18 – 36V DC

- Overlayed ripple max. 2,5Vpp

- Withstand against overvoltage bis 60V min. 10 msec

- Current max. 2A

2.3 Plug contact assignment

Notes on the tables below:
- Unless otherwise noted, the switch contacts are switching the reference potential
- plug contacts: Table1 / No ZA9 (Injection moulding machine signal) and Table 2 / No A9 (Handling device /
robot Signal)

- All signals are continuous signals unless otherwise noted.

- The signals are conducted from the signal source to the respective pin.

- Apart from the handling device / robot signals ”Handling device/robot operation mode” (Table 2; B2)
,”Enable mould closure” (Table 2, A6), "Mould area free” (Table 2; A3/C3), "Emergency stop channel 1"
(Table 2; A1/C1) and "Emergency stop channel 2" (Table2; A2/C2) the signals can assume any status
when the handling device / robot is switched off.

- Apart from the injection moulding machine signals "Emergency stop channel 1" (Table 1; ZA1/ZC1) ,
"Emergency stop channel 2" (Table1; ZA2/ZC2), “Safety devices of machine channel 1” (Table 1; ZA3,ZC3)
and “Safety devices of machine channel 2” (Table 1; ZA4,ZC4) the signals can assume any status when the
handling device / robot is switched off.

2.3.1 Table 1: Plug on the moulding injection machine (male).

Signals from the machine to the handling device / robot
Contact
No (male), Signal designation Description
see fig. 2
The switch contact must be open when the injection moulding machine emergency stop
ZA1 Emergency stop of machine
device is being actuated. Opening the switch contact causes emergency stop of the handling
ZC1 channel 1
device / robot.
The switch contact must be open when the injection moulding machine emergency stop
ZA2 Emergency stop of machine
device is being actuated. Opening the switch contact causes emergency stop of the handling
ZC2 channel 2
device / robot.

EUROMAP 67 Page 4 of 10
EUROMAP 67 Version 1.0

Contact
No (male), Signal designation Description
see fig. 2
The switch contact is closed when safety devices (e.g. safety guards, footboard safety, etc.)
on the injection moulding machine are operative so that dangerous movements of the
ZA3 Safety devices of machine
handling device / robot are possible. The signal is active in any operation mode. The signal
ZC3 channel 1
must be the result of limit switch contact series of mould area safety devices according to EN
201.
The switch contact is closed when safety devices (e.g. safety guards, footboard safety, etc.)
on the injection moulding machine are operative so that dangerous movements of the
ZA4 Safety devices of machine
handling device / robot are possible. The signal is active in any operation mode. The signal
ZC4 channel 2
must be the result of limit switch contact series of mould area safety devices according to EN
201.
HIGH signal when the moulding is a reject. HIGH signal when the mould is open and must
ZA5 remain HIGH at least until "Enable mould closure"
Reject
Optional (see table 2: handling device / robot signals contact No A6.). It is recommended to have
HIGH signal already when the mould opening starts.

HIGH signal when the mould closing is completed. Note: The signal "Enable mould closure"
ZA6 Mould closed
is then no longer required (see table 2: handling device / robot signals contact No A6)

HIGH signal when mould opening position is equal or more than required position.
Inadvertent alteration to mould opening stroke smaller than that required for the handling
ZA7 Mould open position
device / robot to approach must be impossible. The signal must remain HIGH as long as the
(handling device / robot)
mould is open and must not be interrupted by a change of operation mode or safety guard
opening.
HIGH signal when mould opening reaches a set position smaller than mould opening
position (see table 1: injection moulding machine signals contact No ZA7). The signal
remains HIGH to the end of mould opening position. Two sequences are possible with this
signal:
a) Mould opening stops on intermediate position and gives start signal to handling device
ZA8 Intermediate mould opening
/ robot. Mould opening restarts with the signal "Enable full mould opening" (see table 2:
Optional position
handling device / robot signals contact No A7).
b) Mould opening does not stop on intermediate position, however gives the signal to
handling device / robot. At this sequence the signals “ Enable full mould opening” (see
table 2: A7) and “Mould area free” (table2: A3/C3) are not in use.
LOW signal when intermediate mould opening position is not in use.
Handling device / robot
ZA9 24 V DC
reference potential
HIGH signal when the injection moulding machine is able to be operated with handling
Enable operation with device / robot. This signal shall not be used to start the handling device / robot. If the signal
ZB2 handling device / robot turns LOW during the operation mode of the handling device / robot "operation with injection
(Automatic) moulding machine", it is recommended that the handling device / robot continues its
automatic cycle until the end position.
HIGH signal when the ejector has been finally (e.g. after the number of its set cycles)
retracted regardless of the moving platen position. The signal is the acknowledgement for
ZB3 Ejector back position the "Enable ejector retraction" signal (see table 2: handling device / robot signals contact No
B3), when the ejector sequence is selected. It is recommended to have HIGH signal when
the ejector sequence is not in use.
HIGH signal when the ejector has been advanced. The signal is the acknowledgement signal
ZB4 Ejector forward position for the "Enable ejector advance,,(see table 2: handling device / robot signals contact No B4).
It is recommended to have HIGH signal when the ejector sequence is not in use.
Core pullers 1 in position 1
HIGH signal when the core pullers 1 are in position 1
ZB5 (Core pullers 1 free for
(see table 2: handling device / robot signals contact No B5).
Optional handling device / robot to
It is recommended to have LOW signal when the core puller sequence is not in use.
approach)
Core pullers 1 in position 2 HIGH signal when the core pullers 1 are in position 2
ZB6
(Core pullers 1 in position (see table 2: handling device / robot signals contact No B6).
Optional
to remove moulding) It is recommended to have LOW signal when the core puller sequence is not in use.
Core pullers 2 in position 1
HIGH signal when the core pullers 2 are in position 1
ZB7 (Core pullers 2 free for
(see table 2: handling device / robot signals contact No B7).
Optional handling device / robot to
It is recommended to have LOW signal when the core puller sequence is not in use.
approach)
Core pullers 2 in position 2 HIGH signal when the core pullers 2 are in position 2
ZB8
(Core pullers 2 in position (see table 2: handling device / robot signals contact No B8).It is recommended to have LOW
Optional
to remove moulding) signal when the core puller sequence is not in use.

ZC5 Reserved for future use of EUROMAP

ZC6 Reserved for future use of EUROMAP

ZC7 Reserved for future use of EUROMAP

EUROMAP 67 Page 5 of 10
EUROMAP 67 Version 1.0

Contact
No (male), Signal designation Description
see fig. 2
Not fixed by EUROMAP, manufacturer
ZC8
Dependent

Supply from handling

ZC9 0V
device / robot

2.3.2 Table 2: Plug on the moulding injection machine (female).

Signals from the handling device / robot to the machine

Contact
No (female), Signal designation Description
see fig. 2
The switch contact must be open when the handling device / robot emergency stop is being
Emergency stop of actuated. The switch contact opening causes emergency stop of the injection moulding
A1
handling device / robot machine. The switch contact must be operative if the handling device / robot is switched off. It
C1
Channel 1 is recommended that the switch contact is operative when the handling device / robot is
unselected.
The switch contact must be open when the handling device / robot emergency stop is being
Emergency stop of actuated. The switch contact opening causes emergency stop of the injection moulding
A2
handling device / robot machine. The switch contact must be operative if the handling device / robot is switched off. It
C2
Channel 2 is recommended that the switch contact is operative when the handling device / robot is
unselected.
The switch contact is closed when the handling device / robot is outside the mould area and
does not interfere with mould opening and closing movements. The switch contact must be
opened when the handling device / robot leaves its start position. If the switch contact is open
neither opening nor closing of the mould may occur. However the injection moulding machine
A3
Mould area free may ignore this signal when mould opening is carried out after e.g. an intermediate stop (see
C3
table 1: injection moulding machine signals contact No ZA8), if the optional sequence is
selected on the injection moulding machine. The signal must have the described effect even
when the handling device / robot is switched off. It is recommended to close the switch contact
when the handling device / robot is unselected.

A4
Reserved for future use by EUROMAP
C4

A5 Not fixed by EUROMAP, manufacturer dependent

A6 Enable mould closure HIGH signal when the handling device / robot is retracted enough for start of mould closure.
The signal must remain HIGH at least until "Mould closed" (see table 1: injection moulding
machine signals contact No ZA6) is available. If the signal is LOW as a result of a fault, mould
closing must be interrupted. The signal "Enable mould closure" must not be a logical "or" with
either other signals, e.g. "Close safety guard" or a push button in any operation mode. The
signal must be HIGH if the handling device / robot is switched off. It is recommended to have
HIGH signal when the handling device / robot is unselected.
HIGH signal when the handling device / robot has taken the part and allows to continue mould
A7 Enable full mould opening. The signal must remain HIGH until "Mould open" signal is given by the injection
Optional opening moulding machine (see table 1: injection moulding machine signals contact No ZA7).

A8 Reserved for future use by EUROMAP

Supply from injection

A9 moulding machine 24V DC
24V DC /2A

Handling device / robot

LOW signal when the handling device / robot mode switch is "Operation with injection moulding
operation mode
B2 machine". HIGH signal when the handling device / robot mode switch is "No operation with
(operation with handling
injection moulding machine". HIGH signal when the handling device / robot is switched off.
device / robot)
HIGH signal when the handling device / robot enables the movement for ejector back. The
B3 Enable ejector back signal must remain HIGH at least until "Ejector back" signal is given by injection moulding
machine (see table 1: injection moulding machine signals contact No ZB3).
HIGH signal when the handling device / robot enables the movement for ejector forward. The
B4 Enable ejector forward signal must remain HIGH at least until "Ejector forward" signal is given by the injection
moulding machine (see table 1: injection moulding machine signals contact No ZB4).

EUROMAP 67 Page 6 of 10
EUROMAP 67 Version 1.0

HIGH signal when the handling device / robot is in position to enable the movement of the core
Enable movement of core
pullers 1 to position 1. It is recommended that the signal remains HIGH at least until "Core
pullers 1 to position 1
pullers 1 in position 1" signal is given by injection moulding machine (see table 1: injection
B5 (Enable movement for
moulding machine signals contact No ZB5).
Optional handling device / robot to
The signal shall remain at least until position 2 has been left.
approach freely)
(see table 1: injection moulding machine signals contact No ZB6).
HIGH signal when the handling device / robot is in position to enable the movement of the core
Enable movement of core pullers 1 to position 2. It is recommended that the signal remains HIGH at least until "Core
pullers 1 to position 2 pullers 1 in position 2" signal is given by injection moulding machine
B6
(Enable core pullers 1 to (see table 1: injection moulding machine signals contact No ZB6).
Optional
remove the moulding) The signal shall remain at least until position 1 has been left.
(see table 1: injection moulding machine signals contact No ZB5).
HIGH signal when the handling device / robot is in position to enable the movement of the core
Enable movement of core
pullers 2 to position 1. It is recommended that the signal remains HIGH at least until "Core
pullers 2 to position 1
B7 pullers 2 in position 1" signal is given by injection moulding machine
(Enable movement for
Optional (see table 1: injection moulding machine signals contact No ZB7).
handling device / robot to
The signal shall remain at least until position 2 has been left.
approach freely)
(see table 1: injection moulding machine signals contact No ZB8).
HIGH signal when the handling device / robot is in position to enable the movement of the core
Enable movement of core pullers 2 to position 2. It is recommended that the signal remains HIGH at least until "Core
B8 pullers 2 to position 2 pullers 2 in position 2" signal is given by injection moulding machine
Optional (Enable core pullers 2 to (see table 1: injection moulding machine signals contact No ZB8).
remove the moulding) The signal shall remain at least until position 1 has been left.
(see table 1: injection moulding machine signals contact No ZB7).

C5 Not fixed by EUROMAP, manufacturer dependent

C6 Reserved for future use by EUROMAP

C7 Reserved for future use by EUROMAP

C8 Not fixed by EUROMAP, manufacturer dependent

Supply from injection

C9 0V
moulding machine

EUROMAP 67 Page 7 of 10
EUROMAP 67 Version 1.0

3 Ejector sequences (Example)

The following sequence as shown in the time diagram is used

Table2/B4: Enable ejector forward

Table1/ZB4: Ejector forward position
Table2/B3: Enable ejector back
Table1/ZB3: Ejector back position

4 Core puller sequences (Examples)

In general position 1 and 2 are used for synchronization between the injection moulding machine and the
handling device / robot, where position 1 is preferable the position for free movement of the handling device /
robot through the mould area. Position 1 and 2 are used alternating.

4.1 Core puller 1 or core puller 2

4.1.1 Core puller 1 (2) moving in two directions

Position 1 is equivalent to ejector back, position 2 is equivalent to ejector forward

Table1/ZB5 (ZB7): Core pullers 1 in

position 1
Table2/B6 (B8): Enable movement
of core pullers 1 to position 2
Table1/ZB6 (ZB8): Core pullers 1 in
position 2
Table2/B5 (B7): Enable movement
of core pullers 1 to position 1

4.1.2 Core puller 1 (2) moving in one direction

Example: Unscrewing gear box
Table2/B6 (B8): Enable movement
of core pullers 1 to position 1
Table1/ZB5 (ZB7): Core pullers 1 in
position 1

Explanation:

min. max. signal during

auxiliary line

EUROMAP 67 Page 8 of 10
EUROMAP 67 Version 1.0

5 Handling device / robot power supply

Power is supplied through a Cekon socket at a voltage of 3/N/PE 400 V / 16 A (see IEC-Pub. 617 part 2 for the
designation) or according to the specification of the user.

6 Sources of supply
Supplier HARTING
Plug type Han 50 D
Pin insert 09 21 025 3001
Pin insert “Z” 09 21 025 3011
Socket insert 09 21 025 3101
Socket insert “Z” 09 21 025 3111
Address HARTING Electric
GmbH & Co.KG
Wilhelm-Harting-Str. 1
32339 Espelkamp
Germany

EUROMAP 67 Page 9 of 10
EUROMAP 67 Version 1.0

EUROMAP

Europäisches Komitee der Hersteller von Kunststoff- und

Gummimaschinen

European Committee of Machinery Manufacturers for the Plastics

and Rubber Industries

Comité Européen des Constructeurs de Machines pour

Plastiques et Caoutchouc

Comitato Europeo Costruttori Macchine per Materie Plastiche e

Gomma

See you again

http://www.euromap.org

Copyright by EUROMAP

EUROMAP 67 Page 10 of 10