BUNDELKHAND INSTITUTE OF ENGINEERING &TECHNOLOGY ,

JHANSI

Unit 1 design Philosophies and WSM (2018-19) CO1

1. Explain under reinforced, over reinforced and balance section in WSM by
deriving the equation of moment of Resistances.
2. Define Neutral Axis, Moment of Resistance, Lever Arm, Balance section in
WSM
3. Explain the advantages and limitation of working stress method over limit
state method.
4. Derive design constant [k, j & R] for neutral axis, lever arm and moment of
resistances constant for singly reinforced beam. Also calculate the values of
k, j & R for M20 grade concrete and Fe415 grade of steel. [By WSM].
5. Calculate the allowable of the singly reinforced beam by working stress
method. The width and effective depth are 450mm, 715mm. It is reinforced
with 8 Numbers of mild steel bars having dia 20mm assuming M20 grade
concrete.
6. A singly reinforced concrete beam is of 300 mm width and 500 mm
effective depth. It is reinforced with 6 Nos. of 16 mm HYSD bar. Assuming
M 20 concrete, determine its moment of resistance according to the working
stress Method
7. A R.C. beam of rectangular section 230 mm x 400 mm is reinforced with 4 x
12 mm dia.bars provided with an effective cover of 35 mm. Calculate
Moment of Resistance of the Section and the maximum uniformly
distributed super imposed load excluding self – weight of beam, this beam
can carry if it is simply supported over a span of 3.5 m. Use M 20 concrete
and Fe 415 steel. (use W.S.M.)
BUNDELKHAND INSTITUTE OF ENGINEERING &TECHNOLOGY ,
JHANSI

Unit 2 Design by beams LSM (2018-19) CO2

1) Derive Equation for limiting depth of neutral axis and moment of resistances
for balanced, under reinforced and over reinforced section by using LSM.
2) Explain. i) Stress strain relationship for concrete. ii) Stress stain relationship
for steel in LSM.
3) Rectangular beam is 23 cm wide and 40 cm deep up to the centre of
reinforcement. Find the area of reinforcement required if it has to resist a
moment of 50 kNm. Use M 20 concrete mix and Fe 415 steel.
4) A singly reinforced beam 300 mm X 600 mm is reinforced with 4 bars of 20
mm diameter with an effective cover of 50mm. effective span is 4.5m.
Assuming M20 concrete & Fe415 steel, find the value of central load P that
can be carried by the beam.
5) Calculate moment of Resistance of a Singly Reinforced RCC beam 300 mm
wide and 550 mm deep effective is reinforced with 4 x 20 mm  bars M 20
concrete & Fe 415 Steel. Find a concentrated load which a beam can support
at centre, if span of beam is 4.0 m (LSM).
6) Design a singly reinforced rectangular beam for a effective span of 5 m
subjected to live load of 12 kN/m over entire span. Calculate main
reinforcement and shear reinforcement. Give all necessary checks as per the
IS 456. Draw neat reinforcement sketch.
BUNDELKHAND INSTITUTE OF ENGINEERING &TECHNOLOGY ,
JHANSI

Unit 3 design for shear in RCC beam (2018-19) CO3

1. Write a note on causes and control of cracks in concrete.
2. Explain moment curvature relationship and deflection control of beams
3. A RCC beam 250 x 500 mm has a clear span of 5.5 m. The beam has 2 – 20
mm bars going in to the support. Factored shear force is 140 KN. Check for
development length of Fe 415 and M 20 grade of concrete is used.
4. Explain in brief the various measure for deflection control as per IS 456 :
2000.
5. A simply supported beam 300 mm x 600 mm effectives is reinforced with 5
bars of 25 mm dia bars. It carries a uniformly distributed load of 80KN/m
over an effective span of 6m. out of the 5 main bars two bars can be bent up
safely near the supports. Design the shear reinforcement for the beam. Use
M 20 grade concrete and Fe 415 steel.
BUNDELKHAND INSTITUTE OF ENGINEERING &TECHNOLOGY ,
JHANSI

Unit- 4 Analysis and design of slabs (2018-19) CO4

1. A hall of effective dimensions 7.5m x 15m provided with the beam at 3m c/c
forming the five slab panels each of 7.5m x 15m (effective).Design the slab
panel as continuous slab using LSM method for following details (a) Live
load = 2.5KN/Sqmtrs (b) Floor finish=0.5KN/Sqmtrs.Use M20 and Fe415
steel.

2. Design the continuous R.C.C slab for the hall 3 x 13.5m effective. The slab
is supported on three beams eachof 300mm wide and are equally placed. The
end of slab supported on 300mm brick wall. The slab carry L.L =3.5 KN/m
and floor finish =1 KN.Use M20 grade concrete and Fe415 steel. Draw the
reinforcement details

3. Design the one way continuous slab for the fig as shown below

Take L.L=3KN/Sqmtrs and F.F=0.5KN/Sqmts.Use M20 grade concrete and

Fe415 steel
4. Design a Two - way slab for panel size 4.5 m x 6.0 m (effective) carrying a
live load of 2 4 kN m and cement concrete flooring of 20 mm thick. The slab
is having one short edge discontinuous and all other edges are continuous.
Use M 20 Mix & Fe 415 steel. Sketch the reinforcement details.
5. Design a RCC slab for a room size 3m x 4m. center to center of support. The
corners of the slab is held down. Use Live load on the slab as 4kN/m2 ,
M20 grade concrete and Fe415 steel. Draw neat reinforcement sketch.
BUNDELKHAND INSTITUTE OF ENGINEERING &TECHNOLOGY ,
JHANSI

Unit -5 Assignment design of columns (2018-19) CO5

1. Design the short axially loaded column of size 420 mm x 600 mm and
having 3 m unsupported length of column .The column is subjected to axial
load of 2000 KN and is effectively held in position but not restrained against
rotation at both ends. Use M20 and Fe415 Steel. Draw the reinforcement
details also

2. Design the short helically reinforced circular column having unsupported

length is 3.7 m which carry an axial load of 1210KN.Assume effective
length is equal to unsupported length. Use M20 and Fe415 Steel. Draw the
reinforcement details also

3. Design the short axially loaded column which carry an axial load of
500KN.It is having the effective length of 3 m.Assume one least dimension
of column is 300 mm. Use M20 and Fe415 Steel. Draw the reinforcement
details also.

4. Design the short helically reinforced circular column having effective length
is 4.5 m. It is subjected to axial load of 1500KN. Use M20 and Fe415 Steel.
Draw the reinforcement details also

5. Design the column for ultimate axial load of 600KN and it is also subjected
to moment of 90KN-m acting @ An axis which is bisecting the depth of
column. Width of the supporting beam is 300 mm.Use M20 and Fe415
steel and draw reinforcement details.

6. Design the short axially circular column with helical rings for the load of
1200 KN and diameter of column 400 mm. Use M20 and Fe415 Steel.
Draw the reinforcement details also

7. Design the short axially loaded column which carry an axial load of 1450
KN.It is having the effective length of 4.5 m.Assume one least dimension of
column is 300 mm. Use M20 and Fe415 Steel. Draw the reinforcement
details also.
BUNDELKHAND INSTITUTE OF ENGINEERING &TECHNOLOGY ,
JHANSI

Unit 1 design Philosophies and WSM (2019-20) CO1

1. What are the limitation of WSM
2. Explain the advantages and limitation of working stress method over limit
state method.
3. Design a beam subjected to a bending moment of 50kNm by working stress
design. Adopt width of beam equal to half the effective depth. Assume the
permissible stresses in the concrete and steel are not to exceed 7 N/mm2 and
140 N/mm2, take m = 13.33
4. Discuss about the various test performed on the concrete
5. Design a beam subjected to a bending moment of 60kNm by working stress
design. Adopt width of beam equal to half the effective depth. Assume the
permissible stresse in the concrete and steel are not to exceed 7 N mm2 and
140 N mm2 , take m = 13.33
6. RCC beam 230 mm x 520 mm overall is reinforced with 4 bars of 20 mm
diameter. The beam has to carry a super imposed land of 55 KN/m including
self-weight of the beam over an effective span of 5m. Find the actual
stresses developed in steel and concrete. The effective cover is 40 mm. Take
modular ratio m = 13.33. Also find the compressive stress in concrete at 50
mm from top of the beam and draw bending stress diagram.
BUNDELKHAND INSTITUTE OF ENGINEERING &TECHNOLOGY ,
JHANSI

Unit 2 Design by beams LSM (2019-20) CO2

1. Explain causes and control of cracking in concrete due to loading
temperature and Shrinkage.
2. Explain in brief the various measure for deflection control as per IS
456:2000
3. Calculate the ultimate moment of Resistance of a Doubly Reinforced
Rectangular Beam of size 230 mm x 450 mm reinforced with 5x20 mm  on
tension side and 3 x 20 mm  on compression side at an effective cover of
50mm on either side. Use M20 concrete & Fe415 steel
4. A doubly reinforced beam 250 mm x 600 mm size is required to resist an
ultimate moment of 310 kNm and ultimate shear force of 70 kN. Using M20
concrete and Fe415 steel, calculate the quantity of steel required and shear
reinforcement. The effective cover to tension steel is 55 mm and for
compression steel is 40 mm.
5. Design a RC beam 700mm350 effective section, subjected to a bending
moment of 300kNm. Adopt M20concrete and Fe415 steel. Sketch
reinforcement details
6. Determine Moment of Resistances of a rectangular section reinforced with a
steel of area
2
600mm on the tension side. The width of the beam is 200mm, effective
depth 600mm. The grade of concrete is M20 & Fe250 grade steel is used.
7. A simply supported T beam has flange width of 2500mm and flange
thickness of 120 mm. The effective span of beam is 4m. The effective depth
of beam is 600 mm and its width 300 mm. It is reinforced with 8 – 20 mm
diameter, Fe415 grade steel. Determine the moment of resistances of the
section. Use M20 grade of concrete.
8. Determine Moment of Resistance of a T-Beam with following data.
Flange Width = 1200 mm, Depth of Flange = 110 mm, Effective Depth = 600
mm, Width of Web = 300 mm, Area of Steel in Tension = 6 x 20 mm dia.Use
M20 grade concrete and Fe415 steel.
9. A doubly reinforced beam 250 mm x 600 mm size is required to resist an
ultimate moment of 310 kNm and ultimate shear force of 70 kN. Using M20
concrete and Fe415 steel, calculate the quantity of steel required and shear
BUNDELKHAND INSTITUTE OF ENGINEERING &TECHNOLOGY ,
JHANSI

reinforcement. The effective cover to tension steel is 55 mm and for

compression steel is 40 mm.

10.Calculate the moment of Resistance of T - Beam as shown in fig. Assume M

20 Mix and Fe 415 grade steel.

11.Determine Moment of Resistance of a T-Beam with following data. Flange

Width = 1200 mm, Depth of Flange = 110 mm, Effective Depth = 600 mm,
Width of Web = 300 mm, Area of Steel in Tension = 6 x 20 mm dia. Use
M20 grade concrete and Fe415 steel.
12.Calculate the depth of neutral axis and ultimate moment of resistance of T
beam section for the following data. Flange width = 800 mm, Flange
thickness = 150mm, Web width = 300mm Effective depth = 420mm Area of
tension reinforcement = 14701mm2 Assume = M 25 grade concrete and Fe
415 grade of steel
13.A simply supported T beam has flange width of 2400 mm and flange
thickness of 120 mm. The effective span of beam is 3.6m. The effective
depth of beam is 580 mm and its width 300 mm. It is reinforced with 8 – 20
mm diameter, Fe 415 grade steel. Determine the moment of resistances of
the section. Use M 20 grade of concrete
14.Design a singly reinforced rectangular beam for a effective span of 5 m
subjected to live load of 12 kN/m over entire span. Calculate main
reinforcement and shear reinforcement. Give all necessary checks as per the
IS 456. Draw neat reinforcement sketch.
BUNDELKHAND INSTITUTE OF ENGINEERING &TECHNOLOGY ,
JHANSI

Unit-3 design for shear in RCC beam (2019-20) CO4

1. Explain in brief the various measure for deflection control as per IS 456 :
2000
2. Explain the behaviour of reinforced and plain concrete beam under the shear
force.
3. Discuss about the shear requirement in RCC beam as per the IS 456:2000
4. An R.C. Beam has an effective depth of 450 mm and a breadth of 300 mm.
It contains 6 x 20 mm bars. If fck 25N /mm2 and fy 415N/ mm2 , calculate
the shear reinforcement needed for factored shear force of 400 kN.
5. A Rectangular beam section is 300 mm wide and is subjected to an ultimate
moment of 80 kN - m and ultimate shear of 50 kN and an ultimate torsion of
35 kN-m. Design the section. Use M 20 concrete and Fe 415 Steel.
BUNDELKHAND INSTITUTE OF ENGINEERING &TECHNOLOGY ,
JHANSI

Unit- 4 Analysis and design of slabs (2019-20) CO4

1. Design the one way continuous slab for following details. A hall of effective
dimensions 8.5 m x 14m is Provided with beam 3.5m c/c forming the panels
of size 3.5x x8.5m (effective).The slab carry L.L =3.5 KN/m2 and floor
finish =1 KN. Use M20 grade concrete and Fe415 steel. Draw the
reinforcement

2. Design the one way continuous slab for the fig as shown below

Take L.L=3KN/Sqmtrs and F.F=0.5KN/Sqmts.Use M20 grade concrete and

Fe415 steel
3. Design the one way continuous slab for following details. A hall of effective
dimensions 7.5 m x 15 m is Provided with beam 3 m c/c forming the panels
of size 7.5 m x15 m (effective).The slab carry L.L =2.5 KN2 & floor finish
=1 KN/m2. Use M20 grade concrete and Fe415 steel. Draw the
reinforcement
4. Design the canopy slab(Cantilever slab) 4m x 1.5 m in plan fixed in 300 mm
thk wall carrying the L.L of 2.5 KN/Sqmtrs & F.F of 1KN/Sqmtrs . Use
M20 grade concrete and Fe415 steel. Draw the reinforcement details
5. Design the main reinforcement for a continuous SLAB for following details
No. of span = 3, Each span length = 3.5 m c/c, Live Load = 3.0 kN/m2
Concrete M20, Steel Fe415, Draw sketch.