NAME:___________________________________________ COURSE CODE:___________________________ SCORE: __________________/30

If you think the answer is not in the choices, write the correct answer

1. An air receiver has a diameter of 30 in and a design pressure of 8000 psi. factor of 0.012 via the Morse formula. The wicket gate has a diameter of 2.5
The compressor is three staged with a total power of 75 hp. Air intake is 0.2 m. What is the brake power in MW if the mechanical efficiency is 65%.
kg/s, 10°C, 15 psi. Find thickness of the receiving tank in inches if it is A. 15 B. 20 C. 35 D. 38 E. 18 F. 16
cylindrical.
A. 0.55 B. 7.02 C. 0.70 D. 14.05 E. 1.40 F. 5.05 14. A hydroelectric turbine has an elevation head of 80 meters and a hv of 2
meters, Blade diameter is 3 meters. The head loss is based on a length of 130
2. A vertical tank 3 meters in diameter receives water from a pump 5 meters meters, with a friction factor of 0.012 using the Morse formula. The wicket
below its bottom. The pump suction is 1.5 meters below the pump gate has a diameter of 2.5 meters. Find the brake power in MW if we change
centerline. The tank is 0.5 mm thick with a maximum stress of 193 GPa. Find the blade diameter to 2.5 meters?
the water power in hp if the flowrate is 30 gpm. A. 8.74 B. 6.07 C. 20.68 D. 14.36 E. 26.09 F. 37.57
A. 63.2 B. 47.2 C. 0.47 D. 0.018 E. 0.025 F. 0.25
15. An 8 stage compressor has a suction of 100 kPa and a discharge of 8MPa.
3. The cylinder of a compressor is 2.5 x 7 in with a thickness of 0.25”. The If the intercoolers are cylindrical, find the longitudinal stress in the 5th
maximum stress of the metal used is 130 ksi. Assume the factor of safety is intercooler. The diameter is 2 inches and the thickness is 5.25 mm.
2.5. The compressor is single stage and intakes hot air at 14.7 psi and 18°C A. 3.74 B. 7.48 C. 1.87 D. 1.78 E. 7.84 F. 3.47
and discharges it at 194°F. What is the polytropic exponent “n”?
A. 1.022 B. 1.012 C. 1.022 D. 1.042 E. 1.032 F. 1.052 16. A compressor has 1 x 10^99 stages has a suction of 100 kPa and a
discharge of 1x10^99 kPa. Find the pressure(kPa) in the 9x10^98 intercooler.
4. The cylinder of a compressor is 2.5 x 7 in with a thickness of 0.25”. The A. 1 x10^89 B. 3x10^89 C. 5x10^99 D. Math Error E. Infinity F. 4x10^95
maximum stress of the metal used is 130 ksi. Assume the factor of safety is
2.5. The compressor is single stage and intakes hot air at 14.7 psi and 18°C 17. A compressor of 1 x 10^99 stages suction of 100 kPa and a discharge of
and discharges it at 194°F. What is the compressor power in kJ/kg? 1x10^99 kPa. Find the pressure(kPa) in the 95x10^95 intercooler.
A. 1742.666 B. 666C. 960 D. 418 E. 512.666 F. 353.95 A. 835 B. 8.35x10^97 C. 8.35x10^95 D. Math Error E. Infinity F. 9.5x10^95

5. A pump’s discharge is closed by a flange 8” in diameter with a bolt circle of 18. A compressor of 1 x 10^99 stages has a suction of 1 kPa and a discharge
6”. The pump power is 150 hp, Suction pressure is -5 psi with a volume flow of 1x10^99 kPa. Find the pressure(kPa) in the 95x10^95 intercooler.
rate of 1000 gpm. The Yield Strength of the bolt is 29000 ksi. The bolt length A. 8.72 B. 8.7x10^97 C. 8.7x10^95 D. Math Error E. 8700 F. 8.72x10^98
and diameter is 2.5” and 1/4” with a maximum deformation of 0.0015 inch.
How many bolts are needed? 19. A compressor has 8 stages, the discharge of each intercooler is 25°C while
A. 5 B. 6 C. 7 D. 8 E. 9 F. 10 entrance is at 80°C. Find the total heat rejected in BTU/s if the compressor
takes 5 m^3/s at 15°C at a pressure of 1 psig vacuum.
6. A pump’s discharge is closed by a flange 8” in diameter with a bolt circle of A. 315.59 B. 2524.75 C. 299.14 D. 2393.13 E. 2663.61 F. 332.95
6”. The pump power is 150 hp, Suction pressure is -5 psi , 1000 gpm. E=
29000 ksi. The bolt length and diameter is 2.5” and 1/4” , with a maximum 20. A fan whose static efficiency is 40% has a capacity of 1000 ft^3/min
deformation of 0.0015 inch. After rounding the number of bolts to the pushes against 2” H2O. What is the torque in lb-in at 60Hz, 4 poles.
nearest whole number, what is the force experienced by each bolt in kips? A. 9.00 B. 10.00 C. 11.00 D. 12.00 E. 0.015 F. 0.19
A. 0.8 B. 1.0 C. 1.2 D. 1.4 E. 1.6 F. 1.8
21. 10°F of air enters a 75°C coil and leaves at 603R. Find the Contact Factor.
7. A pump’s discharge is closed by a flange 8” in diameter with a bolt circle of A. 0.15 B. 0.51 C. 1.34 D. -8.12 E. 0.78 F. 0.85
6”. The pump power is 150 hp, Suction is -5 psig , 1000 gpm. E = 29000 ksi.
The bolt length and diameter is 2.5” and 1/4” with a maximum deformation 22. 35°C of air enters a coil and leaves at 10°C. The contact factor is .0.85,
of 0.0015 inch. What is the discharge pressure in kgf/cm^2? find the coil temperature in °F
A. 77.1 B. 71.7 C. 17.7 D. 11.7 E. 15.7 F. 14.7 A. -205 B. 141.48 C. 254.67 D. 42.06 E. -131.67 F. 102.94

8. A pump’s discharge is closed by a flange 8” in diameter with a bolt circle of 23. A 150 kPa container contains the gases N2O, CH4, SO2, CO2. What is the
6”. The pump power is 150 hp, Suction is at -5 psig , 1000 gpm. The Yield mass(kg) of N2O if it is isolated in a 0.8 m^3 tank at 8°C.
Strength of the bolt is 29000 ksi. The bolt length and diameter is 2.5” and A. 0.21 B. 0.86 C. 0.08 D. 0.013 E. 1.25 F. 0.59
1/4” with a deformation of 0.0015 inch. What force in kN is experienced by
the flange around the area enclosed by the bolt circle? 24. A 150 kPa container contains the gases N2O, CH4, SO2, CO2. What is the
A. 1.7 B. 1.8 C. 1.9 D. 2.0 E. 2.1 F. 2.2 mass(kg) of CO2 if it is isolated in a 0.8 m^3 tank at a temperature of 8°C.
A. 0.59 B. 1.25 C. 0.013 D. 0.65 E. 0.86 F. 0.21
9. A pump’s water power is 150 hp @ 1000 GPM. The mechanical efficiency is
80%. What Torque in lb-in is experienced by this pump if it runs at a specific 25. A 25m^3 vessel contains the gases N2O, CH4, SO2, CO2 at 15°C. What is
speed of 907.41 rpm ?. the Partial pressure of SO2 if each gas has a mass of 1 kg.
A. 285.44 B. 0.65 C. 1739.48 D. 13022 E. 0.21 F. 0.25 A. 13.22 B. 1.49 C. 1.6 D. 0.05 E. 11.25 F. 11.84

10. A pump’s water power is 150 hp @ 1000 GPM. The mechanical efficiency 26. Compute the enthalpy of air in kJ/kg at 85%RH and 21°C db.
is 80%. What is its shaft’s angle of twist in degrees if it has a specific speed of A. 74.54 B. 50.72 C. 54.76 D. 68.07 E. 57.74 F. 57.47
907.41 rpm. Shaft diameter is 65 mm , length is 1216 mm and G= 80GPa.
A. 0.30 B. 0.25 C. 0.20 D. 0.15 E. 0.5 F. 5.55 27. 2.5 m^3/s of Air enters a cooling tower at 21°C db and w=0.015, leaves at
95% RH 50°C. Find the change in enthalpy (kW).
11. A hydroelectric turbine has an elevation head of 80 meters and a hv of 2 A. 666.66 B. 202.15 C. 11.73 D. 261.34 E. 59.19 F. 606.56
meters. The head loss is based on a length of 130 meters, with a friction
factor of 0.012 using the darcy weisbach formula. The wicket gate has a 28. 2.5 m^3/s of Air enters a cooling tower at 21°C db and w=0.015, leaves at
diameter of 2.5 meters. What is the torque in kN-m if the efficiency is 75% 85% RH 50°C. Find the temperature rise in °C of cooling water at 5 Liters/s.
and the specific speed is 1000 rpm? A. 25.43 B. 9.65 C. 31.84 D. 6.85 E. 81.34 F. 67.58
A. 112.78 B. 100 C. 5.33 D. 5.53 E. 5.35 F. 211.87
29. 0.5m^3/s of Air enters an airconditioner at 50°F 85%RH and cools it to
12. A hydroelectric turbine used has an elevation head of 80 meters and a hv 21°C db at w=0.015. . Refrigerant (has n = 1.1, mw= 45 kg/kmol) flows at 10
of 2 meters. The head loss is based on a length of 130 meters, with a friction kg/min and compressed from -20°C to 100°C. Find the COP for cooling
factor of 0.012 using the darcy weisbach formula. The wicket gate has a A. 3.38 B. 2.38 C. 1.38 D. 4.38 E, 5.38 F. 6.38
diameter of 2.5 meters. What is the brake power in MW if the mechanical
efficiency is 65%. 30. A dryer has a 17% wet basis moisture wet feed and 3% wet basis
A. 15 B. 20 C. 35 D. 38 E. 18 F. 16 moisture of dried product. Find the moisture removed for every 5 kg of solids
in the final product.
13. A hydroelectric turbine has an elevation head of 80 meters and a hv of 2 A. 0.187 B. 0.395 C. 0.234 D. 0.0.934 E. 0.168 F. 0.84
meters. The head loss is based on a length of 130 meters, with a friction