CB2S Module Datasheet

Version: 20220913

Online Version
 Contents

Contents

1 Product overview 2
1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.2 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2 Module interfaces 4
2.1 Dimensions and package . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2 Pin definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3 Electrical parameters 11
3.1 Absolute electrical parameters . . . . . . . . . . . . . . . . . . . . . 11
3.2 Normal working conditions . . . . . . . . . . . . . . . . . . . . . . . 11
3.3 RF power consumption . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.4 Working current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4 RF parameters 15
4.1 Basic RF features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.2 Wi-Fi transmission performance . . . . . . . . . . . . . . . . . . . . . 15
4.3 Wi-Fi receiving performance . . . . . . . . . . . . . . . . . . . . . . . 16
4.4 Bluetooth transmission performance . . . . . . . . . . . . . . . . . . 16
4.5 Bluetooth receiving performance . . . . . . . . . . . . . . . . . . . . 17

5 Antenna information 18
5.1 Antenna type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.2 Antenna interference reduction . . . . . . . . . . . . . . . . . . . . . 18

6 Packaging information and production instructions 19

6.1 Mechanical dimensions . . . . . . . . . . . . . . . . . . . . . . . . . 19
6.2 Production instructions . . . . . . . . . . . . . . . . . . . . . . . . . 22
6.3 Recommended oven temperature curve and temperature . . . . . . . 24
6.4 Storage conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

7 MOQ and packaging information 27

8 Appendix-Statement 28

I
 Contents

CB2S is an embedded low-power Wi-Fi module that Tuya has developed. It consists
of a highly integrated RF chip BK7231N and a few peripherals. CB2S not only sup-
ports the Wi-Fi AP and STA modes, but also supports the Bluetooth LE.

1 / 30
 1 Product overview

1 Product overview

CB2S is built in with a 32-bit MCU whose running speed can be up to 120 MHz, a
2-MB flash memory, and a 256-KB RAM, so as to support the Tuya IoT cloud connec-
tion. The MCU instructions specially extended for signal processing can effectively
implement audio encoding and decoding.

Besides, it has rich peripherals, such as PWM and UART. There are 5 channels of
32-bit PWM output, making the chip very suitable for high-quality LED control.

1.1 Features

• Built in with the low-power 32-bit CPU, which can also function as an application
processor
• The clock rate: 120 MHz
• Working voltage: 3.0 to 3.6V
• Peripherals: 5 PWMs and 1 UART
• Wi-Fi connectivity

– 802.11 b/g/n
– Channels 1 to [email protected] GHz
– Support WEP, WPA/WPA2, WPA/WPA2 PSK (AES), WPA3 security modes
– Up to +16 dBm output power in 802.11b mode
– Support STA/AP/STA+AP working mode
– Support SmartConfig and AP network configuration manners for Android
and iOS devices
– Onboard PCB antenna with a gain of 0 dBi
– Working temperature: -40°C to 85°C

• Bluetooth connectivity

– Support the Bluetooth LE V5.2

– Support the transmit power of 6 dBm in the Bluetooth mode
– Complete Bluetooth coexistence interface
– Onboard PCB antenna with a gain of 0 dBi

1.2 Applications

• Intelligent building

2 / 30
 1 Product overview

• Smart household and home appliances

• Smart socket and light
• Industrial wireless control
• Baby monitor
• Network camera
• Intelligent bus

3 / 30
 2 Module interfaces

2 Module interfaces

2.1 Dimensions and package

The dimensions of CB2S are 14.99±0.35 mm (W)×17.91±0.35 mm (L) ×2.8±0.15

mm (H). The dimensions of CB2S are as follows:

4 / 30
 2 Module interfaces

5 / 30
 2 Module interfaces

2.2 Pin definition

Pin number Symbol I/O type Function

1 3V3 P Power supply

3V3
2 P6 I/O Support
hardware
PWM and
correspond to
P6 of the IC

6 / 30
 2 Module interfaces

Pin number Symbol I/O type Function

3 GND P Power supply

reference
ground
4 P7 I/O Support
hardware
PWM and
correspond to
P7 of the IC
5 RX1 I/O UART_RX1,
which is used
for receiving
user data and
corresponds
to P10 of the
IC. Do not pull
it up. By
default, the
MCU serial
port should be
in low-level or
high-
impedance
state.
6 P8 I/O Support
hardware
PWM and
correspond to
P8 of the IC

7 / 30
 2 Module interfaces

Pin number Symbol I/O type Function

7 TX1 I/O UART_TX1,

which is used
for
transmitting
user data and
corresponds
to P11 of the
IC. Do not pull
it up. By
default, the
MCU serial
port should be
in low-level or
high-
impedance
state.
8 ADC I/O ADC, which
corresponds
to P23 of the
IC
9 P24 I/O Support
hardware
PWM and
correspond to
P24 of the IC
10 CEN I/O Reset pin
11 P26 I/O Support
hardware
PWM and
correspond to
P26 of the IC

8 / 30
 2 Module interfaces

Pin number Symbol I/O type Function

Test point RX2 I/O UART_RX2,

which
corresponds
to P1 of the
IC. This pin is
not allowed to
use.
Test point TX2 I/O UART_TX2,
which is used
for outputting
logs and
corresponds
to P0 of the IC

9 / 30
 2 Module interfaces

Pin number Symbol I/O type Function

Test point CSN I/O Mode

selection pin.
If it is
connected to
the ground
before being
powered on,
enter the
firmware test
mode. If it is
not connected
or connected
to VCC before
being
powered on,
enter the
firmware
application
mode. It
corresponds
to P21 of the
IC.

Note:

• P indicates a power supply pin and I/O indicates an input/output pin.

• For the MCU solution, see CBx Module.

10 / 30
 3 Electrical parameters

3 Electrical parameters

3.1 Absolute electrical parameters

Minimum Maximum
Parameter Description value value Unit

Ts Storage -55 125 °C

temperature
VBAT Power supply -0.3 3.9 V
voltage
Static TAMB-25°C -4 4 KV
electricity
discharge
voltage
(human body
model)
Static TAMB-25°C -200 200 V
electricity
discharge
voltage
(machine
model)

3.2 Normal working conditions

Minimum Typical Maximum

Parameter Description value value value Unit

Ta Working -40 - 85 °C
tempera-
ture
VBAT Power 3 3.3 3.6 V
supply
voltage

11 / 30
 3 Electrical parameters

Minimum Typical Maximum

Parameter Description value value value Unit

VOL I/O low VSS - VSS+0.3 V

level
output
VOH I/O high VBAT-0. 3 - VBAT V
level
output
Imax I/O drive - 6 20 mA
current

3.3 RF power consumption

Peak
Transmit value
Working power/re- Average (Typical
status Mode Rate ceive value value)) Unit

Transmit 11b 11Mbps +16dBm 81 240 mA

Transmit 11g 54Mbps +15dBm 82 238 mA
Transmit 11n MCS7 +14dBm 85 234 mA
Receive 11b 11Mbps Constantly 73 82 mA
receive
Receive 11g 54Mbps Constantly 75 82 mA
receive
Receive 11n MCS7 Constantly 75 82 mA
receive

3.4 Working current

12 / 30
 3 Electrical parameters

Working Maximum
status, Ta = value (Typical
Working mode 25°C Average value value) Unit

Quick network The module is 63 245 mA

connection in the fast
state network
(Bluetooth) connection
state and the
Wi-Fi indicator
flashes fast
Quick network The module is 80 270 mA
connection in the hotspot
state (AP) network
connection
state and the
Wi-Fi indicator
flashes slowly
Quick network The module is 78 246 mA
connection in the fast
state (EZ) network
connection
state and the
Wi-Fi indicator
flashes fast
Network The module is 25 342 mA
connected connected to
state the network
and the Wi-Fi
indicator is
always on
Network The module is 63 242 mA
disconnected disconnected
state and the Wi-Fi
indicator is
always off

13 / 30
 3 Electrical parameters

Working Maximum
status, Ta = value (Typical
Working mode 25°C Average value value) Unit

Module The CEN pin 330 - μA

disabled of the module
is connected
to the ground.

14 / 30
 4 RF parameters

4 RF parameters

4.1 Basic RF features

Parameter Description

Working frequency 2.412 to 2.484 GHz

Wi-Fi standard IEEE 802.11 b/g/n (channels 1 to 14)
Data transmission rate 11b: 1, 2, 5.5, 11 (Mbps)
11g: 6, 9, 12, 18, 24, 36, 48, 54 (Mbps)
11n: HT20 MCS 0 to 7
11n: HT40 MCS 0 to 7
Antenna type PCB antenna

4.2 Wi-Fi transmission performance

Minimum Maximum
Parameter value Typical value value Unit

Average RF - 16 - dBm
output power,
802.11b CCK
Mode 11M
Average RF - 15 - dBm
output power,
802.11g
OFDM Mode
54M
Average RF - 14 - dBm
output power,
802.11n
OFDM Mode
MCS7

15 / 30
 4 RF parameters

Minimum Maximum
Parameter value Typical value value Unit

Frequency -20 - 20 ppm

error

4.3 Wi-Fi receiving performance

Minimum Maximum
Parameter value Typical value value Unit

PER<8%, RX - -88 - dBm

sensitivity,
802.11b DSSS
Mode 11M
PER<10%, RX - -74 - dBm
sensitivity,
802.11g
OFDM Mode
54M
PER<10%, RX - -73 - dBm
sensitivity,
802.11n
OFDM Mode
MCS7
PER<10%, RX - -96 - dBm
sensitivity,
Bluetooth LE
1M

4.4 Bluetooth transmission performance

16 / 30
 4 RF parameters

Minimum Maximum
Parameter value Typical value value Unit

Working 2402 - 2480 MHz

frequency
Air rate - 1 - Mbps
Transmit -20 6 20 dBm
power
Frequency -150 - 150 KHz
error

4.5 Bluetooth receiving performance

Minimum Maximum
Parameter value Typical value value Unit

RX sensitivity - -96 - dBm

Maximum RF -10 - - dBm
signal input
Inter- - - -23 dBm
modulation
Co-channel - 10 - dB
suppression
ratio

17 / 30
 5 Antenna information

5 Antenna information

5.1 Antenna type

CB2S uses the PCB antenna.

5.2 Antenna interference reduction

To ensure optimal Wi-Fi performance when the Wi-Fi module uses an onboard PCB
antenna, it is recommended that the antenna be at least 15 mm away from other
metal parts.

To prevent adverse impact on the antenna radiation performance, avoid copper or

traces within the antenna area on the PCB.

18 / 30
 6 Packaging information and production instructions

6 Packaging information and production instructions

6.1 Mechanical dimensions

The dimensions of CB2S are 14.99±0.35 mm (W)×17.91±0.35 mm (L) ×0.8±0.1

mm (H)

19 / 30
6 Packaging information and production instructions

20 / 30
6 Packaging information and production instructions

21 / 30
 6 Packaging information and production instructions

6.2 Production instructions

1. For the Tuya in-line module, wave soldering is most preferred and manual sol-
dering is less preferred. After being unpacked, the module must be soldered
within 24 hours. Otherwise, it must be put into the drying cupboard where
the RH is not greater than 10%; or it needs to be packaged under vacuum
again and record the exposure time (the total exposure time cannot exceed
168 hours).
2. Wave soldering devices and materials:

• Wave soldering equipment

• Wave soldering fixture
• Constant-temperature soldering iron
• Tin bar, tin wire, and flux

22 / 30
 6 Packaging information and production instructions

• Thermal profiler

3. Baking devices:

• Cabinet oven
• Anti-electrostatic and heat-resistant trays
• Anti-electrostatic and heat-resistant gloves

4. The module needs to be baked in the following cases:

• The packaging bag is damaged before unpacking.

• There is no humidity indicator card (HIC) in the packaging bag.
• After unpacking, circles of 10% and above on the HIC become pink.
• The total exposure time has lasted for over 168 hours since unpacking.
• More than 12 months have passed since the sealing of the bag.

5. Baking settings:

• Temperature: 40°C and ≤ 5% RH for reel package and 125°C and ≤5% RH
for tray package (please use the heat-resistant tray rather than a plastic
container).
• Time: 168 hours for reel package and 12 hours for tray package.
• Alarm temperature: 50°C for reel package and 135°C for tray package.
• Production-ready temperature after natural cooling: < 36°C.
• Re-baking situation: If a module remains unused for over 168 hours after
being baked, it needs to be baked again.
• If a batch of modules is not baked within 168 hours, do not use the wave
soldering to solder them. Because these modules are Level-3 moisture-
sensitive devices, they are very likely to get damp when exposed beyond
the allowable time. In this case, if they are soldered at high temperatures,
it may result in device failure or poor soldering.

6. In the whole production process, take electrostatic discharge (ESD) protective

measures.
7. To guarantee the quality of products, you must pay attention to the following
items: The amount of soldering flux, the height of the wave peak, whether
the tin slag and copper content in the wave soldering tank exceed standards,
whether the window and thickness of the wave soldering fixture are appropri-
ate, and whether the wave soldering oven temperature curve is appropriate.

23 / 30
 6 Packaging information and production instructions

6.3 Recommended oven temperature curve and temperature

Set oven temperatures according to the following temperature curve of wave sol-
dering. The peak temperature is 260°C±5°C.

Recommended soldering temperature:

Suggestions on
oven temperature Suggestions on
curve of wave manual soldering
soldering temperature

Preheat 80 to 130°C Soldering 360±20°C

temperature temperature
Preheat time 75 to 100s Soldering time ＜ 3s/point
Peak contact time 3 to 5s NA NA
Temperature of tin 260±5°C NA NA
cylinder

24 / 30
 6 Packaging information and production instructions

Suggestions on
oven temperature Suggestions on
curve of wave manual soldering
soldering temperature

Ramp-up slope ≤2°C/s NA NA

Ramp-down slope ≤6°C/s NA NA

6.4 Storage conditions

Storage conditions for a delivered module:

• The moisture-proof bag is placed in an environment where the temperature is

below 40°C and the relative humidity is lower than 90%.

• The shelf life of a dry-packaged product is 12 months from the date when the
product is packaged and sealed.

• There is a humidity indicator card (HIC) in the packaging bag.

Figure 1: HIC-In-line module.png

25 / 30
 6 Packaging information and production instructions

Figure 2: HIC-In-line module.png

26 / 30
 7 MOQ and packaging information

7 MOQ and packaging information

Shipping The number The number

Product packaging of modules of reels per
number MOQ (pcs) method per reel carton

CB2S 4400 Tape reel 1100 4

27 / 30
 8 Appendix-Statement

8 Appendix-Statement

FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this device.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Note: This device has been tested and found to comply with the limits for a Class
B digital device, according to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential instal-
lation. This device generates, uses, and can radiate radio frequency energy and, if
not installed and used following the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this device does cause harmful interference to radio or television reception, which
can be determined by turning the device off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the device and receiver.
• Connect the device to an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement

This device complies with FCC radiation exposure limits set forth for an uncontrolled
rolled environment. This device should be installed and operated with a minimum
distance of 20cm between the radiator and your body.
Important Note
This radio module must not be installed to co-locate and operate simultaneously
with other radios in the host system except following FCC multi-transmitter product
procedures. Additional testing and device authorization may be required to operate
simultaneously with other radios.
The availability of some specific channels and/or operational frequency bands are
country-dependent and are firmware programmed at the factory to match the in-
tended destination. The firmware setting is not accessible by the end-user.

28 / 30
 8 Appendix-Statement

The host product manufacturer is responsible for compliance with any other FCC
rules that apply to the host not covered by the modular transmitter grant of certi-
fication. The final host product still requires Part 15 Subpart B compliance testing
with the modular transmitter installed.

The end-user manual shall include all required regulatory information/warnings as

shown in this manual, including “This product must be installed and operated with
a minimum distance of 20 cm between the radiator and user body”.

This device has got an FCC ID: 2ANDL-CB2S. The end product must be labeled in a
visible area with the following: “Contains Transmitter Module FCC ID: 2ANDL-CB2S”
.

This device is intended only for OEM integrators under the following conditions:

The antenna must be installed such that 20cm is maintained between the antenna
and users, and the transmitter module may not be co-located with any other trans-
mitter or antenna.

As long as the 2 conditions above are met, further transmitter tests will not be re-
quired. However, the OEM integrator is still responsible for testing their end-product
for any additional compliance requirements required with this module installed.

Declaration of Conformity European Notice

Hereby, Hangzhou Tuya Information Technology Co., Ltd declares that this module
product is in compliance with essential requirements and other relevant provisions
of Directive 2014/53/EU, 2011/65/EU. A copy of the Declaration of conformity can
be found at https://www.tuya.com.

29 / 30
 8 Appendix-Statement

This product must not be disposed of as normal household waste, in accordance with
the EU directive for waste electrical and electronic equipment (WEEE-2012/19/EU).
Instead, it should be disposed of by returning it to the point of sale, or to a municipal
recycling collection point.

The device could be used with a separation distance of 20cm from the hu-
man body.

30 / 30