ER100-(M)

Flow Monitor

CERTIFICATE BINDER
E-SERIES CERTIFICATE BINDER
Disclaimer
This Certificate binder is created to provide as accurate and authoritative information regarding the
subjects covered as was available at the time of writing. The copyright owner of this Certificate
binder cannot take any responsibility or liability for any errors or omissions in this Certificate binder
or for discrepancies arising from the features of any actual item in the respective refit being different
from those shown in this Certificate binder. The publisher and copyright owner shall not be liable
under any circumstances, for any consequential, special, contingent, or incidental damages or injury,
financial or otherwise, suffered by any part arising out of, connected with, or resulting from the use
of this Certificate binder or the information contained therein.

Copyright
© 2016 Fluidwell B.V. - All rights reserved
Nothing from this Certificate binder may be reproduced, or transmitted in any form or by any means,
electronic or mechanical, including photocopying, recording or any information storage or retrieval
system without prior written approval by Fluidwell B.V..

Trademarks
All trademarks used in this publication are the property of their respective owners.

Document control
This Certificate binder is part of the documentation set that came with the E-Series. It is the
responsibility of the copy holder to keep the Certificate binder and the related appendices up-to-date.
We reserve the right to make changes of any kind without prior written notice. Please visit our internet
site for the latest information and (product) updates.

FW_E-SERIES_CB_A1_AE Page 3
CERTIFICATE BINDER E-SERIES
Certification
The CE marking is a mandatory conformity marking that allows the manufacturers
to circulate (industrial) products freely within the internal market of the European
Economic Area (EEA). The CE mark self-certifies that the products have met the
minimum EEA health, safety and environmental requirements for the consumer and
workplace safety.
The CE marking is also found on products sold outside the EEA that are manufactured
in, or designed to be sold in, the EEA.

The ATEX Directive uses a special logo in addition to the CE logo to show that the
product is suitable for use in an Explosive Atmosphere. The rating for the Explosive
Atmosphere is given on the related certificate and the product label.

The IEC System for Certification to Standards relating to Equipment for use in Explo-
sive Atmospheres uses a special logo to show that the product is suitable for use in
an Explosive Atmosphere. The rating for the Explosive Atmosphere is given on the
related certificate and the product label.

The Canadian Standards Association (CSA) is a nonprofit Nationally Recognized

Testing Laboratory that serves the business, the industry, the government and the
consumers in Canada and the global marketplace. The CSA-US Mark qualifies as
an alternative to the UL Mark.
The rating for the use of the product is given on the related certificate and the product
label.

The Factory Mutual Insurance Company (FM) is an international property insurance

and loss prevention engineering company, specilized in loss prevention services
primarily to large corporations throughout the world in the Highly Protected Risk
(HPR) property insurance market sector.
The FM APPROVED mark shows that that the product conforms to the highest na-
tional and international standards. The rating for the use of the product is given on
the related certificate and the product label.

Version a1
Checked in 2016-02-23

Page 4 FW_E-SERIES_CB_A1_AE
E-SERIES CERTIFICATE BINDER
Table of content
1 CE CERTIFICATION ..................................................................................................................... 6
2 ATEX CERTIFICATION ................................................................................................................. 7
3 IECEX CERTIFICATION ................................................................................................................ 9
4 C-CSA-US CERTIFICATION ......................................................................................................... 12
5 FM CERTIFICATION ..................................................................................................................... 17

FW_E-SERIES_CB_A1_AE Page 5
CERTIFICATE BINDER E-SERIES

1 CE certification

Page 6 FW_E-SERIES_CB_A1_AE
E-SERIES CERTIFICATE BINDER

2 ATEX certification

FW_E-SERIES_CB_A1_AE Page 7
CERTIFICATE BINDER E-SERIES

Page 8 FW_E-SERIES_CB_A1_AE
E-SERIES CERTIFICATE BINDER

3 IECEx certification

FW_E-SERIES_CB_A1_AE Page 9
CERTIFICATE BINDER E-SERIES

Page 10 FW_E-SERIES_CB_A1_AE
E-SERIES CERTIFICATE BINDER

FW_E-SERIES_CB_A1_AE Page 11
CERTIFICATE BINDER E-SERIES

4 c-CSA-us certification

Certificate of Compliance
Certificate: 70010647 Master Contract: 208772

Project: 70010647 Date Issued: August 27, 2015

Issued to: Fluidwell B.V.

Voltaweg 23
5466 AZ Veghel
NETHERLANDS

Attention: R.Amiot

The products listed below are eligible to bear the CSA Mark shown

Issued by: E.Giusti

E.Giusti

PRODUCTS

CLASS 2258 02 - PROCESS CONTROL EQUIPMENT - For Hazardous Locations

CLASS 2258 82 - PROCESS CONTROL EQUIPMENT - For Hazardous Locations - Certified to US Standards

Class I, Division 1, Grps A, B, C, D (except model codes Exxx - z - x- x - HC_ and Exxx - z - x_ - x_ - HU_). Which
are for groups B, C, D only)
Class II/III, Division 1, Grps E, F, G
Class I, Zone 1, AEx d IIC T6/T5 Gb
Zone 21, AEx tb IIIC T85°C/T100°C Db

Flowrate indicator/totalizer model Exxx-z with Analog and Pulse Signal Inputs, Alarm and/or pulse Outputs,
Linearization and communication options.
Electrical ratings: 8-30 Vdc or 65-250 Vac (incl. 10% tolerance), 50/60Hz, 4.5W for T6 and 9.2W for T5. Battery
powered and/or supplied externally, the indicators can be equipped with a pulse/relay output and a sensor supply
output.
Ambient operating temperature range is -40°C to +70°C.
The indicator enclosure ensures a degree of protection of at least IP66/IP67 in accordance with CAN/CSA 60529
and ANSI/IEC 60529 and Type 4X as well.

DQD 507 Rev. 2012-05-22 Page 1

Page 12 FW_E-SERIES_CB_A1_AE
E-SERIES CERTIFICATE BINDER

Certificate: 70010647 Master Contract: 208772

Project: 70010647 Date Issued: August 27, 2015

Model code is as follows:

Exxx - z - A_ - C_ - H_ _ - I_ - O_ - P_ - X_ - Z_

xxx = model number representing firmware in range 000 – 999 which does not affect approval
z = Primary sensor input
A_ = Analog output
C_ = Communication output
H_ _ = Enclosure
I_ = Additional input
O_ = Digital outputs
P_ = Power requirements
X_ = Hazardous area
Z_ = Options

For only the safety relevant options, the model code reduces to:
Exxx-z-xx-xx-H_ _-xx- O_-P_-xx-xx.

Symbol “z” and “x” represent a letter denoting different non-safety relevant options related to LV/LC signaling
and software functionality.

Digital output
OR mechanical relay(s) and passive transistor outputs
OT passive transistor outputs
OX No digital outputs

Power requirements
PB Lithium battery powered
PD 9 - 27V DC + sensor supply.
PX basic power input 9 - 27V DC

Note: following specifications appear in the manufacturer’s instructions:

-The property class of the hexagon socket head screw of process connection A (cylindrical joint) is A2-70 or
better;
-The details of the flameproof joints are specified in the manufacturer’s instructions;
-The painted aluminum enclosure shall be installed in such a way that danger of ignition due to electrostatic
charges is avoided.
-Guidance are given in the manufacturer’s instructions since the temperature at the entry point is above 70°C.

DQD 507 Rev. 2012-05-22 Page 2

FW_E-SERIES_CB_A1_AE Page 13
CERTIFICATE BINDER E-SERIES

Certificate: 70010647 Master Contract: 208772

Project: 70010647 Date Issued: August 27, 2015

APPLICABLE REQUIREMENTS

CAN/CSA C22.2 No. 0-10 General Requirements - Canadian Electrical Code, Part II
CAN/CSA C22.2 No. 61010-1-12 Safety requirements for electrical equipment for measurement, control,
and laboratory use - Part 1: General requirements
CAN/CSA C22.2 No. 60079-0:11 Electrical Apparatus for Explosive Gas Atmospheres - Part 0: General
Requirements
CAN/CSA C22.2 No. 60079-1:11 Electrical Apparatus for Explosive Gas Atmospheres - Part 1: Equipment
protection by flameproof enclosures "d"
CAN/CSA-C22.2 No. 60079-31:12 Explosive atmospheres - Part 31: Equipment dust ignition protection by
enclosure "t"
CAN/CSA-C22.2 No. 30-M1986 Explosion-Proof Enclosures for Use in Class I Hazardous Locations
CAN/CSA-C22.2 No. 25-1966 Enclosures for Use in Class II Groups E, F, and G Hazardous Locations
CAN/CSA C22.2 No. 60529:05(R2010) Degrees of protection provided by enclosures (IP Code)

ANSI/ISA 61010-1 (82.02.01) Safety requirements for electrical equipment for measurement, control,
and laboratory use - Part 1: General requirements
ANSI/ISA 60079-0 (12.00.01): 2013 Explosive atmospheres – Part 0: Equipment – General Requirements
ANSI/ISA 60079-1 (12.22.01): R2013 Explosive Atmospheres – Part 1: Equipment protection by flameproof
enclosures "d"
FM3600: 2011 Electrical Equipment for Use in Hazardous (Classified) Locations – General
Requirements
FM3615 :2006 Explosionproof Electrical Equipment
ANSI/IEC 60529:2004 Degrees of protection provided by enclosures (IP Code)

MARKINGS

The manufacturer is required to apply the following markings:

• Products shall be marked with the markings specified by the particular product standard.
• Products certified for Canada shall have all Caution and Warning markings in both English and French.

Additional bilingual markings not covered by the product standard(s) may be required by the Authorities Having
Jurisdiction. It is the responsibility of the manufacturer to provide and apply these additional markings, where
applicable, in accordance with the requirements of those authorities.

The products listed are eligible to bear the CSA Mark shown with adjacent indicators 'C' and 'US' for Canada and
US (indicating that products have been manufactured to the requirements of both Canadian and U.S. Standards) or
with adjacent indicator 'US' for US only or without either indicator for Canada only.

The permanent markings appear on a self-adhesive label manufactured by 3M (CUL MH18072) and is mounted
on the surface of the apparatus.

(1) Submittor's name, trademark

(2) Catalogue / Model designation.
(3) Date code / Serial number traceable to month and year of manufacture.

DQD 507 Rev. 2012-05-22 Page 3

Page 14 FW_E-SERIES_CB_A1_AE
E-SERIES CERTIFICATE BINDER

Certificate: 70010647 Master Contract: 208772

Project: 70010647 Date Issued: August 27, 2015

(4) The cCSAus Monogram

(5) Maximum ambient temperature
(6) Certificate number CSA.15.70010647
(7) Hazardous location ratings
(8) Warning: ‘Do not open when an explosive gas atmosphere is present’
Avertissement:’Ne pas ouvrir si une atmosphère explosive est présente’
‘Seal all conduit entries within 18 inches. For Group A seal at enclosure wall’
‘Scellez toutes les entrées de conduits à 18” max. Pour le grpe A, scellez les entrées au droit de
l’enveloppe’

Nameplate is as per drawing Exxx_Exd_XP_DIP_v0.9.1.

Note - Jurisdictions in Canada may require these markings to also be provided in French language. It is the
responsibility of the manufacturer to provide bilingual marking, where applicable, in accordance with the
requirements of the Provincial Regulatory Authorities.

Nameplate adhesive label material approval information:

The permanent markings appear on a self-adhesive label manufactured by 3M (CUL MH18072) and are mounted
on the surface of the apparatus.

DQD 507 Rev. 2012-05-22 Page 4

FW_E-SERIES_CB_A1_AE Page 15
CERTIFICATE BINDER E-SERIES

Supplement to Certificate of Compliance

Certificate: 70010647 Master Contract: 208772

The products listed, including the latest revision described below,

are eligible to be marked in accordance with the referenced Certificate.

Product Certification History

Project Date Description

70010647 August 27, 2015 Original Certification.

DQD 507 Rev. 2012-05-22 Page 1

Page 16 FW_E-SERIES_CB_A1_AE
E-SERIES CERTIFICATE BINDER

5 FM certification

FM Approvals
1151 Boston Providence Turnpike
P.O. Box 9102 Norwood, MA 02062 USA
T: 781 762 4300 F: 781-762-9375 www.fmapprovals.com

CERTIFICATE OF COMPLIANCE
HAZARDOUS (CLASSIFIED) LOCATION ELECTRICAL EQUIPMENT

This certificate is issued for the following equipment:

Exxx – z, a, c, h, l, o, p, x, z. General Purpose Flowrate Indicator

XP/ I/ 1/ ABCD/ T6/ T5 Ta = -40˚C to +70˚C, Type 4X, IP66/67.
DIP/ II, III/ 1/EFG /T6 /T5 Ta = -40˚C to +70˚C.
I/ 1/ AEx d IIC /T6 /T5 Gb Ta = -40˚C to +70˚C.
21/ AEx tb IIIC/ T85˚C/ T100˚C Db Ta = -40˚C to +70˚C.
xxx = Model number representing firmware range: 000 – 999 (Does not affect FM Approval)
z = Primary Sensor Input: A, P or X.
a = Analog Output: AH or AX
c = Communication Output: CB, CH, CR, CU, CT or CX.
h = Enclosure: HA_, HS_, H_A, H_B, H_C, H_D, H_E, H_F, H_G, H_H, HB_, HC_HD_, HT_, HU_, HV_,
H_A, H_C or H_E.
i = Additional Input: IB, IR or IX.
o = Digital Outputs: OR, OT and OX.
p = Power Requirements: PB, PD or PX.
x = Hazardous Area: XD.
z = Options: ZA, ZB, ZF, ZG, ZL or ZX.

Specific Conditions of Use:

1. The property class of the hexagon socket head screws of process connection A (cylindrical joint) is
A2-70 or better.
2. The details of the flameproof joints are specified in the manufacturer’s instructions.
3. The painted aluminum enclosure shall be installed in such a way that danger of ignition due to
electrostatic discharge is avoided. Possible electrostatic hazard – clean only with a moist cloth. Use
only in fixed installations and do not place in areas with rapid airflow.

To verify the availability of the Approved product, please refer to www.approvalguide.com

FM Approvals HLC 5/13 3054369
Page 1 of 3

FW_E-SERIES_CB_A1_AE Page 17
CERTIFICATE BINDER E-SERIES

Equipment Ratings:
Explosionproof for use in Class I, Division 1, Groups A, B, C and D; Dust-ignitionproof for Class II/III,
Division 1, Groups E, F and G; Class I, Flameproof for Class I, Zone 1, AEx d IIC T6/ T5 Gb; and Zone 21,
AEx tb IIIC T85˚C/ T100°C Db Ta = -40°C + 70°C hazardous (classified) locations, indoor/ outdoor use
Type 4X, IP66/67.

FM Approved for:

Fluidwell bv
Veghel, Netherlands

To verify the availability of the Approved product, please refer to www.approvalguide.com

FM Approvals HLC 5/13 3054369
Page 2 of 3

Page 18 FW_E-SERIES_CB_A1_AE
E-SERIES CERTIFICATE BINDER

This certifies that the equipment described has been found to comply with the following
Approval Standards and other documents:

Class 3600 2011

Class 3615 2006
Class 3616 2011
Class 3810 2005
ANSI/ISA 60079-0 2013
ANSI/ISA 60079-1 2013
ANSI/ISA 60079-31 2013
ANSI/ISA 60529 2004
ANSI/NEMA 250 2008

Original Project ID: 3054369 Approval Granted: January 22, 2016

Subsequent Revision Reports / Date Approval Amended

Report Number Date Report Number Date

FM Approvals LLC

22 January 2016
J.E. Marquedant Date
Manager of Electrical Systems

To verify the availability of the Approved product, please refer to www.approvalguide.com

FM Approvals HLC 5/13 3054369
Page 3 of 3

FW_E-SERIES_CB_A1_AE Page 19
 Brodie International

P.O. Box 450 (30459-0450)

19267 Highway 301 North
Statesboro, GA, 30461
USA

Email: [email protected]
Phone: +1 (912) 489-0200
Fax: +1 (912) 489-0294

BR_ER100_CB_v1706_01.docx