Scribd
Upload
86 views1 page

Tds 51 PDF

This technical data sheet provides specifications for the "51" series centrifugal blower. The blower comes in 1 to 10 stages, has a 6" flanged inlet and outlet, and operates at speeds between 3600 to 4400 rpm. Materials of construction include cast iron, cast aluminum, steel, and stainless steel. Dimensions, weights, and performance curves for inlet air flow and discharge pressure are provided for each blower size.

Uploaded by

Amazonas Manutenção
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
86 views1 page

Tds 51 PDF

This technical data sheet provides specifications for the "51" series centrifugal blower. The blower comes in 1 to 10 stages, has a 6" flanged inlet and outlet, and operates at speeds between 3600 to 4400 rpm. Materials of construction include cast iron, cast aluminum, steel, and stainless steel. Dimensions, weights, and performance curves for inlet air flow and discharge pressure are provided for each blower size.

Uploaded by

Amazonas Manutenção
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

TECHNICAL DATA SHEET

TECHNICAL DATA “51” SERIES


Number of stage : 1 thru 10 (cast)
Inlet connection : 6” (152 mm) flange, DN 150 PN 10
Outlet connection : 6” (152 mm) flange, DN 150 PN 10
Operating speed : 3600 rpm in direct drive (60Hz), 4400 with
V-belt
Lubrication : Grease lubricated
Impeller diameter : 24” (611 mm)
Impeller tip speed : 374 f/s (114 m/s)
First critical speed : 4706 rpm (9-stage)
Drive : Direct drive or gear box or V-belts
Vibration tolerance : 1.34 mils peak-to-peak (4,5 mm/s RMS)
Shaft end : 1” 3/4 (45 mm), inlet end drive standard.

Air & GAS


MATERIALS OF CONSTRUCTION

Head, Bearing housings : Cast iron FGL 250


Sections : Cast aluminium Al Si 7 Mg (cast iron optional)
Tie rods : 13/16” (20 mm) diameter cold drawn steel A60
Joint sealing compound : RTV IS502 Silicone
Seals (air) : Two graphit rings each end
Seals (gas) : Four carbon rings each end with inert gas injection
Bearings : Ball bearings 6410 C3 per AFBMA B1­0 STANDARD
Shaft : Carbon steel C35 (stainless steel available)
Impellers : Cast aluminium Al Si 10 Mg
Baffle rings : Stainless steel
Motor pedestal : Structural steel.
Base frame installation : Antivibrations pads
1000

WEIGHT
BLOWER
“A“ “B“ “C“
900
Rotor moment of
SIZE inertia kg.m²
Inlet air condition : Pbar = 1013.25 mbar
LBS Kg 800
discharge pressure in mbar

51.01 9.21 (234) 46 (1168) 48 (1219) 937 425 0.35 700


T = 20°C - R.H. = 36 %

51.02 12.83 (326) 52 (1321) 54 (1372) 1047 475 0.71 600

51.03 16.46 (418) 64 (1626) 66 (1676) 1168 530 1.06


500
MODEL 51
51.04 20.08 (510) 64 (1626) 66 (1676) 1256 570 1.41
400
Working Area
51.05 23.71 (602) 70 (1778) 72 (1829) 1366 620 1.76
300
51.06 27.33 (694) 82 (2083) 84 (2134) 1488 675 2.11

51.07 30.96 (786) 82 (2083) 84 (2134) 1576 715 2.47


200

51.08 34.57 (878) 94 (2388) 96 (2438) 1697 770 2.82 100

51.09 38.19 (970) 94 (2388) 96 (2438) 1785 810 3.17 0


0 1000 2000 3000 4000
51.10 41.81 (1062) 98 (2489) 100 (2540) 1895 860 3.52 500 1500 2500 3500 4500

DIMENSIONS ARE IN INCHES AND (MM)


inlet flow in m3/h
ACTUAL DIMENSIONS MAYVARY SLIGHTLY TO SUIT APPLICATION

Values, dimensions and reference in this brochure are approximate and intended as a guide only, not for construction and are subject to change without notice.

CONTINENTAL INDUSTRIE SAS . CONTINENTAL INDUSTRIE SAS . CONTINENTAL INDUSTRIE SAS .


Rev
SP09/2010

You might also like