2PSE

Low Noise Gear Pumps

Technical Brochure
E0.147.0421.11.00IM00
Final revised edition - April 2021
The data in this catalogue refers to the standard product.The policy of Salami S.p.A. consists of a continuous
improvement of its products. It reserves the right to change the specifications of the different products whenever
necessary and without giving prior information.
If any doubts, please contact our sales department.
Contents

Features................................................................... 4
Working Conditions.................................................. 5
Single Unit............................................................... 6
Ports.........................................................................7
Standard Configurations.......................................... 8
SINGLE UNITS ORDERING CODE ...................... 9
MULTIPLE UNITS ORDERING CODE ................. 10
2PSE GEAR PUMPS “SE” SERIES
Low Noise Gear Pumps Aluminium Gear Housing

Features

2PSE is a Low Noise Salami gear pump, available with displacements

from 4.6 cm3/rev to 26 cm3/rev (from 0.27 cu.in/rev to 1.62 cu.in/rev).
Intermittent pressure up to 280 bar (4060 psi).

• Reduction of the flow pulsations of 80%.

• Reduction of the noise emissions by up to 7-9 dB(A) (average)
compared to standard gear pumps.
• Vibration reduction
• Longer pump life

• Gear: Double flank engagement, tooth profile optimization to

reduce relative sliding, specific heat treatment to minimize the gear
deformation.
• Axial balancing bushings optimized to minimize the volume trapped
during teeth engagement.
• High volumetric efficiency achieved by floating bushings and axial
compensation.
• 12 teeth integral shaft: one piece, solid gear.
• Modular construction.
• Compact design.

• Aluminium gear housing, cast iron flanges and covers.

• Double shaft seal.
• Outrigger bearing available.
• Wide range of rear covers with built-in valves.
• Flanges: European, German, SAE A, SAE B.
• Ports: European, German and American standards.
• Shafts: European and American standards.
• Sharing the same gear housing, flanges and rear covers of 2PE
pump.

Applications

• Hydraulic presses, Waste compactors, Forklifts, Drives for elevators/

hoists, Farm vehicles, Municipal vehicles, Earthmoving machines,
Hydraulic steering systems.

Noise Level Reduction

E0.147.0421.11.00IM00

2PE 22.5D
2PE 11.3D
Standard gear pump
S.p.l. [dB(A)]

2PSE 22.5D
2PSE 11.3D

Low noise gear pump

p [bar]

4 www.salami.it
 GEAR PUMPS “SE” SERIES 2PSE
Aluminium Gear Housing Low Noise Gear Pumps

Features
Pressure Ripple Comparison
Pressure (bar)

Time (ms)

Low noise gear pump Standard gear pump

Working Conditions
HYDRAULIC FLUID
Mineral oil according to DIN 51524, other hydraulic fluids on request.

Pump inlet pressure (absolute pressure) 0.8 to 1.5 bar (11.6 to 21.7 psi)

Minimum operating fluid viscosity 12 mm2/sec

Viscosity Max starting viscosity 800 mm2/sec

Suggested fluid viscosity range 17 ÷ 65 mm2/sec

fluid operating temperature range -25 ÷ 80 °C

E0.147.0421.11.00IM00

Temperature fluid operating temperature range with FPM seals (Viton) -20 ÷ 110°C

fluid operating temperature range with HNBR seals* -30 ÷ 110°C

* Available on request

Definition of Pressures

p3 p3 = Peak pressure
p2
p2 = Intermittent operating pressure (1/3 of working time)
p1
p1 = Continuous operating pressure

www.salami.it 5
2PSE GEAR PUMPS “SE” SERIES
Low Noise Gear Pumps Aluminium Gear Housing

Single Unit

Displacements up to 26.6 cm3/rev - 1.62 cu.in./rev

Dimension Dimension Continuous Intermittent Peak Min. speed Max. speed

Displacement Weight
A C pressure p1 pressure p2 pressure p3 at p1 at p2**
TYPE
cm3/rev cu.in/rev mm in mm in bar psi bar psi bar psi min-1 kg lbs

2PSE - 3.2* 3.2 0.19 250 3625 280 4060 300 4350 600 4000 3.00 6.61

2PSE - 3.9* 3.9 0.24 47.1 1.83 23.55 0.93 250 3625 280 4060 300 4350 600 4000 3.05 6.72

2PSE - 4.5 4.6 0.27 250 3625 280 4060 300 4350 600 4000 3.10 6.83

2PSE - 6.5 6.5 0.4 49.95 1.97 25 0.98 250 3625 280 4060 300 4350 600 4000 3.50 7.72

2PSE - 8.3 8.2 0.5 52.8 2.07 26.4 1.04 250 3625 280 4060 300 4350 500 3500 3.60 7.94

2PSE - 10.5 ● 10.6 0.65 56.3 2.22 28.15 1.11 250 3625 280 4060 300 4350 500 3500 3.70 8.16

2PSE - 11.3 11.5 0.68 250 3625 280 4060 300 4350 500 3500 3.75 8.27
59.7 2.35 29.75 1.17
2PSE - 12.5 ● 12.7 0.77 250 3625 280 4060 300 4350 500 3500 3.78 8.33

2PSE - 13.8 13.8 0.84 63.5 2.5 31.75 1.25 250 3625 280 4060 300 4350 500 3500 3.86 8.51

2PSE - 16 16.6 1.01 67.5 2.65 33.75 1.33 250 3625 280 4060 300 4350 400 3000 4.00 8.82

2PSE - 19 19.4 1.15 75.6 2.97 37.80 1.49 220 3140 240 3480 260 3750 400 3000 4.18 9.22

2PSE - 22.5 22.9 1.37 81 3.19 40.5 1.59 200 2900 220 3140 240 3480 400 2750 4.29 9.46

2PSE - 26 26.6 1.62 86.8 3.42 43.4 1.71 180 2610 200 2900 220 3190 300 2500 4.54 10.1

*= Available only as rear pump - ●= Available only for quantity

**=Max speed allowed with p2 pressure working continously at p1 the max. speed must be reduced by10%.

For flanges code:

P1-B1-S2-S3-S6, this dimension is 19 mm (0.75 in.)
B2-B3-B4-B5-K3-K4, this dimension is 16.5 mm (0.65 in.)
E0.147.0421.11.00IM00

17

6 www.salami.it
 GEAR PUMPS “SE” SERIES 2PSE
Aluminium Gear Housing Low Noise Gear Pumps

Ports

TYPE INLET OUTLET

ØD ØA d e ØD ØA d e

From 3.2 13 30
M6
to 8.3 (0.51”) (1.19”)

From 11.3 to 20 13 13 30 13
M6
22.5 (0.79”) (0.51”) (0.51”) (1.18”) (0.51”)
40
M8
22 (1.57”)
26
(0.87”)
Flanged Port

P - European standard

TYPE INLET OUTLET

ØD ØA d e ØD ØA d e

From 3.2 to 20
22.5 (0.78”)
40 13 15 35 13
M6 M6
(1.56”) (0.51”) (0.59”) (1.38”) (0.51”)
22
26
(0.87”)

B - German standard

TYPE INLET OUTLET

A B ØC A B ØC

From 3.2 16 20 14 13
G3/4 G1/2
to 26 (0.62”) (0.78”) (0.54”) (0.51”)
Threaded Port
E0.147.0421.11.00IM00

G - GAS (BSPP)

TYPE INLET OUTLET

A B ØC Y K A B ØC Y K

1-1/16-12 7/8-14
From 3.2 16 20 41 3.3 14 13 34 2.5
UN UNF
to 26 (0.62”) (0.78”) (1.61”) (0.12”) (0.54”) (0.78”) (1.32”) (0.10”)
(SAE 12) (SAE 10)

R - SAE (ODT)

www.salami.it 7
2PSE GEAR PUMPS “SE” SERIES
Low Noise Gear Pumps Aluminium Gear Housing

Standard Configurations

Cover with Rear Ports Cover with Valves

Bearing Support+Continental Shaft

VS VSE
Cover with Valve Cover with Valve
28CP Internal discharge External discharge
European standard
+
Tapered 1:8

26CB
German standard
+
Tapered 1:5 VP/VP1/VPS/VPS1
Cover with
Priority Flow Valve

VPD/VPD1/VPDS/VPDS1
Cover with
Load Sensing Priority Valve

25CL
For Internal
combustion
engines
+
Tapered 1:5

25CF
For Internal
combustion
Flanges+Drive Shaft type
engines with axial
and radial loads
+
Tapered 1:5

52CS
SAE A
+ 03B2/B3 62B4/B5 25B1 52S2 28P1
E0.147.0421.11.00IM00

SAE A splined 9T
German standard German standard German standard SAE A 2 bolts European standard
54CS + + + + +
Tang drive for electric Splined 9T DIN 5482 Tapered 1:5 SAE A splined 9T Tapered 1:8
SAE A motors
+
SAE A splined 11T 25B4/B5 62B1 54S2 62P1
82CS German standard German standard SAE A 2 bolts European standard
SAE A
● + + + +
Tapered 1:5 Splined 9T DIN 5482 SAE A splined 11T Splined 9T DIN 5482
+
5/8 SAE A Parallel 85S2
85CS SAE A 2 bolts
SAE A
● ● ● + ●
3/4 SAE A Parallel
+
3/4 SAE A Parallel 82S2
SAE A 2 bolts
● ● ● + ●
5/8 SAE A Parallel

8 www.salami.it
 SINGLE UNITS ORDERING CODE 2PSE
Low Noise Gear Pumps

Adjustable flow l/min

2PSE - - - - - /

A B C D E F G H I pressure relief valve setting (bar)

TYPE DISPLACEMENTS ► REAR COVERS CODE

A I
4.5 4.6 cm /rev.
3
0.27 cu.in/rev. Adjustable pressure relief valve-Internal discharge VS
6.5 6.5 cm3/rev. 0.40 cu.in/rev. Adjustable setting pressure relief valve-External
VSE
discharge
8.3 8.2 cm3/rev. 0.50 cu.in/rev.
Priority flow valve with excess flow to 2nd actuator VP-VP1
10.5 10.6 cm3/rev. 0.65 cu.in/rev.
Priority flow valve with excess flow to 2nd actuator
VPS-VPS1
11.3 11.5 cm3/rev. 0.68 cu.in/rev. with pressure relief valve

12.5 12.5 cm3/rev. 0.77 cu.in/rev. Load sensing priority valve with dinamic signal VPD-VPD1

13.8 13.8 cm3/rev. 0.84 cu.in/rev. Load sensing priority valve with dinamic signal
VPDS-VPDS1
and pressure relief valve
16 16.6 cm /rev.
3
1.01 cu.in/rev.
Electric unloading valve (12V) EV1/EV3
19 19.4 cm3/rev. 1.18 cu.in/rev.
Electric unloading valve (24V) EV2/EV4
22.5 22.9 cm3/rev. 1.37 cu.in/rev.
Pressure relief and electric unloading valves
EVS1/EVS3
26 26.6 cm3/rev. 1.62 cu.in/rev. (12V)
Pressure relief and electric unloading valves
EVS2/EVS4
ROTATION CODE (24V)
B Pre-arranged for 1.5PE rear PD1.5
Clockwise D
Anti-clockwise S
►OUTRIGGER BEARING CODE
H
PORTS (page 5) CODE For Internal combustion engines CL
C For Internal combustion engines with axial and
Flanged ports CF
P radial loads
european standard
SAE A CS
Flanged ports
B
german standard German standard CB
Threaded ports European standard CP
G
GAS (BSPP)
Threaded ports PORTS POSITION CODE
SAE (ODT)
R G
Side ports (standard configuration) -
►DRIVE SHAFT CODE Rear ports 1
D
Tang drive for electric motors 03
SEAL CODE
Tang drive 04 F
Buna standard (standard configuration) -
Tapered 1:5 25
Viton V
Tapered 1:8 28
SAE A splined 9T 52 ►MOUNTING FLANGES CODE
E
SAE A splined 10T 53 European standard P1
SAE A splined 11T 54
German standard Ø80 B1
E0.147.0421.11.00IM00

SAE B splined 13T

55 German standard Ø52 B2-B3
(Coupling sleeve)
DIN 5480 internal splined German standard Ø50 B4-B5
60
(only for rear pumps)
SAE A 2 bolts S2
9 teeth DIN 5482 splined 62
SAE B 2 bolts S3
5/8” SAE A parallel 82
SAE A 2 bolts (with o-ring on the centering collar) S6
3/4” SAE A parallel 85
German standard with shaft seal Ø52 K3
Tapered 1:5 Continental shaft
26 German standard with shaft seal Ø52 K4
(Only for CB)
Order example: 2PSE 19D, ports SAE (R), drive shaft (54),
► See Technical Catalogue 2PE (E0.120.0219.02.00IM04) mounting flange (S2).
2PSE19D-R54S2

www.salami.it 9
2PSE
Low Noise Gear Pumps MULTIPLE UNITS ORDERING CODE

A1 Adjustable flow l/min

2PSE / - - - - - - /

A B C D E F G H I L pressure relief valve setting (bar)

TYPE DISPLACEMENTS ►REAR COVERS CODE

A L
4.5 4.6 cm /rev.
3
0.27 cu.in/rev. Adjustable pressure relief valve-Internal discharge VS
6.5 6.5 cm /rev.
3
0.40 cu.in/rev. Adjustable setting pressure relief valve-External
VSE
discharge
8.3 8.2 cm3/rev. 0.50 cu.in/rev.
Priority flow valve with excess flow to 2nd actuator VP-VP1
10.5 10.6 cm3/rev. 0.65 cu.in/rev.
Priority flow valve with excess flow to 2nd actuator
VPS-VPS1
11.3 11.5 cm3/rev. 0.68 cu.in/rev. with pressure relief valve

12.5 12.5 cm3/rev. 0.77 cu.in/rev. Load sensing priority valve with dinamic signal VPD-VPD1

13.8 13.8 cm3/rev. 0.84 cu.in/rev. Load sensing priority valve with dinamic signal
VPDS-VPDS1
and pressure relief valve
16 16.6 cm /rev.
3
1.01 cu.in/rev.
Electric unloading valve (12V) EV1/EV3
19 19.4 cm3/rev. 1.18 cu.in/rev.
Electric unloading valve (24V) EV2/EV4
22.5 22.9 cm3/rev. 1.37 cu.in/rev.
Pressure relief and electric unloading valves
EVS1/EVS3
26 26.6 cm3/rev. 1.62 cu.in/rev. (12V)
Pressure relief and electric unloading valves
EVS2/EVS4
(24V)
A1 ►COMBINATION WITH 2PE or 1.5PE
Pre-arranged for 1.5PE rear PD1.5

ROTATION CODE
B I ►OUTRIGGER BEARING CODE
Clockwise D
For Internal combustion engines CL
Anti-clockwise S For Internal combustion engines with axial and
CF
radial loads
PORTS (page 5) CODE SAE A CS
C
Flanged ports German standard CB
P
european standard
European standard CP
Flanged ports
B
german standard PORTS POSITION CODE
H
Threaded ports Side ports (standard configuration) -
G
GAS (BSPP)
Rear ports 1
Threaded ports
R
SAE (ODT)
SUCTION PORTS CODE
G
►DRIVE SHAFT CODE Common Inlet UA*
D
Tang drive for electric motors 03 Separated stages AS

Tang drive 04
SEAL CODE
Tapered 1:5 25
F
Buna standard (standard configuration) -
Tapered 1:8 28 Viton V
SAE A splined 9T 52
►MOUNTING FLANGES
E0.147.0421.11.00IM00

CODE
SAE A splined 10T 53 E
European standard P1
SAE A splined 11T 54
German standard Ø80 B1
SAE B splined 13T
55
(Coupling sleeve) German standard Ø52 B2-B3
DIN 5480 internal splined German standard Ø50 B4-B5
60
(only for rear pumps)
SAE A 2 bolts S2
9 teeth DIN 5482 splined 62
SAE B 2 bolts S3
5/8” SAE A parallel 82
SAE A 2 bolts (with o-ring on the centering collar) S6
3/4” SAE A parallel 85
German standard with shaft seal Ø52 K3
Tapered 1:5 Continental shaft
26 German standard with shaft seal Ø52 K4
(Only for CB)
*UA-Common suction: number 1 - 2 or 3, correspond to the body Order example: 2PSE 19D, ports SAE (R), drive shaft (54),
where inlet is located. mounting flange (S2).
► See Technical Catalogue 2PE (E0.120.0219.02.00IM04) 2PSE19/19D-R54S2

10 www.salami.it
 GEAR PUMPS “SE” SERIES
Aluminium Gear Housing Note

______________________________________________________________________________________________________

______________________________________________________________________________________________________

______________________________________________________________________________________________________

______________________________________________________________________________________________________

______________________________________________________________________________________________________

______________________________________________________________________________________________________

______________________________________________________________________________________________________

______________________________________________________________________________________________________

______________________________________________________________________________________________________

______________________________________________________________________________________________________

______________________________________________________________________________________________________

______________________________________________________________________________________________________

______________________________________________________________________________________________________

______________________________________________________________________________________________________

______________________________________________________________________________________________________

______________________________________________________________________________________________________

______________________________________________________________________________________________________
E0.147.0421.11.00IM00

______________________________________________________________________________________________________

______________________________________________________________________________________________________

______________________________________________________________________________________________________

______________________________________________________________________________________________________

______________________________________________________________________________________________________

www.salami.it 11
SALAMI S.P.A. SALAMI FRANCE
Via Emilia Ovest 1006 22, rue Louis Saillant
69120 Valux en Velin
41123 Modena (Italy)
Lyon
T. +39 059 387 411 T. +33-04-78809941
F. +39 059 387 639 F. +33-04-78803669
[email protected] [email protected]

SALAMI ESPAÑA SALAMI HYDRAULICS N.A INC

Poligono Industrial Armenteres 4630 Crossroads Park Drive
C/Primer de Maig, 18, Nave 4 Liverpool
08980 San Feliu de Llobregat NY 13088 - USA
Barcelona T. +1-315-295-2363
T. +34-93-6665451 F. +1-315-295-2364
F. +34-93-6667826 [email protected]
[email protected]

www.salami.it