® STANDARD DUAL MAGNET
MOUNT THERMOMETER
SINGLE OR DUAL MAX-MIN
LAZY HANDS
FOUR MAGNET INDUSTRIAL
RAILROAD THERMOMETER
S UR FACE
THER MOMET E R S FULLY ENCLOSED
SURFACE THERMOMETER
DIRECT CONTACT
SPOT CHECK®
SPRING HELD
PIPE-SURFACE
CLIP-ON PIPE-SURFACE
THERMOMETER
MINIATURE SPOT CHECK®
THERMOMETER
IR OVEN & SURFACE
THERMOMETER
31 0 -478-1134 LOW COST DIGITAL
THERMOMETERS & PROBES
2301 FEDERAL AVENUE
DIGITAL THERMOMETER
LOS ANGELES, CA 90064-1482 WITH PROBE ATTACHED
310-312-0826 FAX
email:
[email protected] website: http://www.ptc1.com DIGITAL THERMOCOUPLE
THERMOMETER
STANDARD DUAL MAGNET MOUNT
Over one million of these accurate,
affordable surface thermometers are
in service throughout the world. For
more than fifty years PTC® has been
manufacturing this series of special-
ized thermometers. MODEL RANGE DIVISIONS
312F 0°F to 250°F 2°F
Fahrenheit
With many temperature ranges to 313F 0°F to 500°F 5°F
choose from, the dual magnet surface 314F 50°F to 750°F 10°F
thermometer is the logical choice for
making surface measurements. 315F 0°F to 50°F 1°F
330F -100°F to +160°F 2°F
Model 313F 312C -20°F to +120°C 1°C
Celsius
313C -20°C to+250°C 2°C
314C 10°C to 400°C 5°C
315C -15°C to +65°C 1°C
Cross-section of our 330C -70°C to +70°C 2°C
surface thermometer
SINGLE OR DUAL MAX-MIN LAZY HANDS
SINGLE ANCILLARY HAND Features
this handy, resettable peak reading hand is available as
an accessory on PTC®’s Dual Magnet Mount, Four Magnet Accuracy is ±2% of Full Scale Range
Mount, and Tab Mount Surface Thermometers. The ancil- 2” Diameter x 1/2” High
lary hand is reset by turning the reset knob on the front
Weighs only 1-1/2 oz.
of the thermometer. A non-impeding magnetic clutch holds
the hand in place at either the maximum or minimum tem- Select from Fahrenheit or Celsius Ranges
perature reached during a cycle. Optional Single or Dual Max-Min Hands
DUAL MAX-MIN ANCILLARY HANDS Optional Tab Mounts
Max-min hands are available on PTC®’s Dual Magnet
Mount, Four Magnet Mount, and Tab Surface Thermom-
eters as an accessory. The max-min hands remain at the
highest and lowest temperatures reached until they are
reset. Hands are reset by using the reset knob and mag-
netic wand (Part number 314.5 MM).
Magnetic Wand (Part number 314.5 MM).
Model 312F MM shown above
®
FOUR MAGNET INDUSTRIAL RAILROAD
MODEL RANGE DIVISIONS
350FRR -20°F to +160°F 2°
Fahrenheit
312FRR 0°F to 250°F 2°
Model 350FRR 313FRR 0°F to 500°F 5°
314FRR 50°F to 750°F 10°
315FRR 0°F to 150°F 1°
330FRR -100°F to +160°F 2°
Features 350CRR
312CRR
-30°C
-20°C
to +70°C
to +120°C
1°
1°
Celsius
Accuracy of ± 2% of Full Scale Range 313CRR -20°C to +250°C 2°
314CRR 10°C to 400°C 5°
2” Diameter X 1/2” High
315CRR -15°C to +65°C 1°
Weighs only 2 oz. 330CRR -70°C to +70°C 2°
Select from Fahrenheit or Celsius Ranges
Optional Single or Dual Max-Min Hands
ON-SURFACE & IN-SURFACE TAB MOUNTED
Tab mounts can be ordered in place of the standard dual
magnets. Two types of tabs are available for these ther-
mometers. Tab 1 is an on-surface mount and Tab 2 is an in- MODEL RANGE DIVISIONS
312FT1 or T2 0°F to 250°F 2°
Fahrenheit
surface type mount. The drawings show both styles of
mounting. 313FT1 or T2 0°F to 500°F 5°
314FT1 or T2 50°F to 750°F 10°
For in-surface mounting, a hole 1-1/8” diameter by 1/4” 315FT1 or T2 0°F to 150°F 1°
deep needs to be machined in the surface to be measured. 330FT1 or T2 -100°F to +160°F 2°
Pilot holes also need to be drilled for the tab mounting
screws. Both styles of tabs have holes for the screws. 312CT1 or T2 -20°C to +120°C 1°
Celsius
When ordering, please specify whether Tab 1 or Tab 2 313CT1 or T2 -20°C to +250°C 2°
mounting is required. 314CT1 or T2 10°C to 400°C 5°
315CT1 or T2 -15°C to +65°C 1°
330CT1 or T2 -70°C to +70°C 2°
TAB 1 On-Surface Mount TAB 2 In-Surface Mount
310-478-1134
FULLY ENCLOSED SURFACE THERMOMETER
Features
Fully Enclosed--Bimetal Protected from Damage
Accuracy is ±2% of Full Scale Range
2” Diameter X 1/2” High
Weighs only 1 oz.
Select from Fahrenheit or Celsius Ranges
Model 310C
These handy surface temperature ther-
mometers have served the industry for
MODEL RANGE DIVISIONS over fifty years. With their unique design,
Fahrenheit
the bimetal sensor is protected from
309F -50°F to +250°F 2°F
contaminants and damage from handling.
310F 0°F to 300°F 2°F
311F 70°F to 370°F 2°F
With an accuracy of ±2% of full scale
range, these thermometers give fast and
Celsius
309C -50°C to + 110°C 2°C
accurate temperature measurements
310C -10°C to +150°C 2°C
with an inexpensive instrument.
311C 20°C to 180°C 2°C
ACCESSORIES
Part No. 310.7 Magnet & Leaf Spring.
Part No. 310.8 Silicone Grease Adhesive.
These accessories can be used to attach the ther-
mometer to almost any flat nonhorizontal sur-
face. The magnet & Leaf Spring will hold the ther-
mometer to any magnetic (ferrous) surface. Ap- Cross-section of fully enclosed surface
plying a thin coat of the silicone grease to the thermometer shown with optional magnet &
leaf spring accessory.
back of the thermometer will hold it to a non-
magnetic surface.
®
DIRECT CONTACT SPOT CHECK®
CENTER POST 575.8 SPRING HANDLE
DIAL MAX-MIN HANDS (optional)
BIMETAL SPIRAL POINTER
MODEL 573C
BASIC WITH MAGNET & WITH MAX-MIN WITH STAINLESS
RANGE DIV THERMOMETER LEAF SPRING HANDS & 310.7 STEEL DIAL
MODEL NO. MODEL NO. MODEL NO. MODEL NO.
Fahrenheit
0°F to 270°F 2° 570F 570FM 577FM -
50°F to 320°F 2° 571F 571FM 578FM -
50°F to 500°F 5° 572F 572FM 574FM -
50°F to 1000°F 10° 573F 573FM 575FM 575FMSS
Celsius
10°C to 160°C 1° 571C 571CM - -
10°C to 260°C 2° 572C 572CM 574CM -
0°C to 525°C 5° 573C 573CM 575CM 575CMSS
PTC®’s Spot Check® Series of thermometers feature Features
outstanding response and sensitivity. Their extremely
low thermal mass and weight (1/2 ounce), along with a Very Fast Response Time
unique design, assure intimate contact and a very Accuracy is ±2% of Full Scale Range
rapid readout.
1-3/4” Diameter X 1/2” High
The basic thermometer is intended for horizontal or Weighs only 1/2 oz.
slightly curved surfaces. Three options for this basic Select from Fahrenheit or Celsius Ranges
model are available:
Optional Dual Max-Min Hands
1. Thermometer with Magnet & Leaf Spring (310.7) for
attaching to nonhorizontal ferrous surfaces
Magnet & Leaf Spring (Optional)
2. Thermometer with Max-Min Hands and Magnet & Leaf
Spring (310.7)
3. Thermometer with Stainless Steel Dial, Max-Min
Hands, and Magnet & Leaf Spring (310.7)
310-478-1134
SPRING HELD PIPE-SURFACE THERMOMETER
Features
For Pipes with O.D.’s of 3/4” and up
Accuracy is ±2% of Full Scale Range
2” Diameter X 1” High
Weighs only 1-1/2 oz.
Select from Fahrenheit or Celsius Ranges
Spring Kit Included with Each Thermometer Model 483F shown
MODEL RANGE DIVISIONS
Fahrenheit
483F 0°F to 150°F 2°F
486F -50°F to +250°F 2°F
487F 70°F to 370°F 2°F
488F 70°F to 500°F 5°F
MODEL RANGE DIVISIONS
483C -20°C to +70°C 2°C
Celsius
486C -40°C to +120°C 2°C
487C 20°C to 180°C 2°C
488C 20°C to 260°C 2°C Cross-section of spring held
pipe-surface thermometer shown
mounted to pipe
These handy pipe-surface thermometers will fit pipes having
O.D.’s of 3/4” and up. An included spring kit allows the in-
strument to be attached to a pipe or cylinder up to 6” in diam-
eter. Additional kits can be ordered and the springs combine
to accommodate larger diameters. The spring kit (Part No.
486.84) includes three stainless steel springs 3/4”, 2”, and
4” in length. Clips are also included to attach the springs to
the thermometer.
The bimetal sensor is protected from drafts by an insulating
cup which also acts as the unit’s base. The cup is made from
high-temperature plastic for the lower ranges. Models 488F
& 488C have an aluminum insulating cup for higher tempera-
ture use (up to 500°F).
®
CLIP-ON PIPE-SURFACE THERMOMETER
Cross-section of clip-on
pipe-surface thermometer
Model 484 shown with Large, Medium and Small Clip
shown mounted to pipe.
RANGE DIV. For Pipe O.D.’s For Pipe O.D.’s For Pipe O.D.’s
3/4” to 7/8” 1” to 1-5/8” 1-5/8” to 2-3/8”
Fahrenheit
0°F to 150°F 2° 483FS 483FM 483FL
-50°F to +250°F 2° 484FS 484FM 484FL
70°F to 370°F 2° 485FS 485FM 485FL
Celsius
-20°C to +70°C 2° 483CS 483CM 483CL
-40°C to +120°C 2° 484CS 484CM 484CL
20°C to 180°C 2° 485CS 485CM 485CL
Features
Calibrated and designed for pipe-surface tempera- Accuracy is ±2% of Full Scale Range
ture measurement, these thermometers can be used
Snaps Instantly Into Place
on pipes up to 2-3/8” diameter (3/4” minimum diam-
eter). For larger diameter pipes, our spring held Sizes to Fit 3/4” to 2-3/8” O.D. Pipes
thermometers are available. 2” Diameter X 1” High
Ease of use and low cost make these instruments Weighs Approximately 1 oz.
indispensable for monitoring pipe temperatures. Select from Six Temperature Ranges
Thermometers have an accuracy of ±2% of full
Fast Response Time
scale range.
310-478-1134
MINIATURE SPOT CHECK® THERMOMETER
Features
3/4” Diameter X 3/8” High
Weighs only 0.2 oz.
Accuracy is ±2% of Full Scale Range
Model 675F shown actual size Select from Fahrenheit or Celsius Ranges
These thermometers will measure surface temperatures
MODEL RANGE DIVISIONS in a space as small as 1” x 1”; with an accuracy of ±2% of
Fahrenheit
full scale range. The small size of these instruments
674F 0°F to 250°F 2°F
allows minimum “heat-stealing” from the heated surface.
675F 0°F to 500°F 2°F
676F 50°F to 750°F 10°F
The bimetal sensor is protected from drafts with a cup
which also acts as the unit’s base. The bimetal sensor
comes in close thermal contact with the surface to be
measured, providing the thermometer with a fast re-
MODEL RANGE DIVISIONS sponse time.
Celsius
674C 0°C to 135°C 5°C the 675 Series can be used for testing the temperature
675C -20°C to +250°C 5°C of electronic parts. An isotherm of an area can be con-
676C 10°C to 400°C 5°C structed by employing several of these instruments and
then plotting the readings.
DIAL POINTER
LAZY HAND
BIMETAL SPIRAL
Cross-section of thermometer
on heated surface.
®
IR OVEN & SURFACE
MODEL RANGE DIVISIONS
Fahrenheit
580F 50°F to 800°F 10°F
580FM 50°F to 800°F 10°F
With 310.7
MODEL RANGE DIVISIONS
Celsius
580C 10°C to 425°C 5°F
580CM 10°C to 425°C 5°F
With 310.7
Model 580F shown above
Cross-section of thermometer
held in place with 310.7 magnet & leaf
spring shown on heated surface.
These I/R thermometers are designed to measure
the radiation temperature of a source. Al- Features
though specifically intended for radiation tem-
peratures, these thermometers will also accu- I.R. Oven & Surface Thermometer
rately measure surface temperatures. Accuracy is ±3% of Full Scale Range
1-21/32” Diameter X 9/16” High
Radiation temperatures from sources such as:
Calrods, wire and ribbon resistance heating Weighs Approximately 0.2 oz.
elements, gas operated heat transfer panels,
Very Fast Response
and incandescent lamps can be measured.
Models 580FM & 580CM Come with Magnet
These models come with a maximum reading hand, & Leaf Spring
which will retain the highest temperature
reached during a cycle.
310-478-1134
LOW COST DIGITAL
THERMOMETER & PROBES
MODEL RANGE DIVISIONS
31308-KF -100°F to +1000°F 1°F
31308-KC -120°C to +550°C 1°C
This low cost digital model features interchangeable
probes for all applications with a range of -100°F to
+1000°F or -120°C to +550°C. Instrument includes a 9-
Volt battery which provides up to 2,000 hours of op-
eration. Display is easy to read with 3/8” high numerals.
Chose from four different probe styles: surface
(31907-K), air (31903-K), immersion (31901-K), and bare
tip (31905-K). Probes are ANSI type K with mini connec-
tors. Probes are not included with the instrument and
Model must be ordered as separate items.
31308-KF
shown with
Part No. PROBE TYPES MODEL
31901-K
Immersion SURFACE 31907-K
Probe AIR 31903-K
IMMERSION 31901-K
BARE TIP 31905-K
DIGITAL THERMOMETER WITH PROBE ATTACHED
MODEL RANGE DIVISIONS
33035 -115.0°F to +500.0°F .1° or1°
-80.0°C to+260.0°C
This model features outstanding accuracy and ease of use,
combined with durability and low cost. The unit’s display is
switchable between °F and °C readouts. Accuracy is ±0.9°F
(or±o.5°C).
The thermometer is sealed against moisture, dirt, and other
contaminants. The instrument’s handle and cable can with-
stand temperatures up to 400°F, Cable length is 32”.
Model 33035 Digital Thermometer
® with Flat Surface Bell Probe
DIGITAL THERMOCOUPLE
THERMOMETER
Model 39658 Model 38653
Interchangeable probes provide Stainless Steel Housing
versatility for this accurate and This digital thermometer is rug-
durable digital thermometer. ged, accurate, and pocket-
The thermometer is switchable sized. This thermometer can be
from °F or °C readings and the switched to read in either °F or
display digits are 1/2” tall, mak- °C and can be used with any
ing them very easy to read. probe listed below. Display is
black-on-silver LCD digits,
Accuracy is ±1% of reading ±1° 0.35” tall. The thermometer
over range of -122°F to +1999°F weighs only 5 ounces.
with the instrument itself at
room temperature (20°C to Accuracy is ±0.7% of reading
30°C). three thermocouple ±1°C (1.8°F). Three different
types are available and probe ranges are available using Type Model 38653
Model 39658
styles are listed below. J,K, or T thermocouples.
TYPE RANGE TYPE RANGE
J -112°F to +1382°F & -80°C to +750°C J -76°F to +1400°F & -60°C to +760°C
K -112°F to +1999°F & -80°C to +1100°C K -40°F to +1832°F & -40°C to+1000°C
T -112°F to +752°F & -80°C to +400°C T -76°F to + 662°F & -60°C to +350°C
PROBE TYPES FOR MODEL 39658 & 38653 DIGITAL THERMOMETERS
310-478-1134
IMMERSION
THERMOMETERS RECORDING THERMOMETER
Model 615
AIR IMMERSION THERMOMETER OVEN RECORDING OVEN THERMOMETER
Model 819F with optional desk stand Model 618
STAINLESS STEEL
STEM THERMOMETER
AIR IMMERSION WALL THERMOMETER
Model 815F
STAINLESS STEEL
ALL-ANGLE STEM THERMOMETER
