International Journal of Advances in Applied Sciences (IJAAS)

Vol. 11, No. 3, September 2022, pp. 253~262

ISSN: 2252-8814, DOI: 10.11591/ijaas.v11.i3.pp253-262  253

Simulation model of 1-phase pulse-width modulation rectifier

by using MATLAB/Simulink

Salam Waley Shneen1, Ghada Adel Aziz2, Fatin Nabeel Abdullah2, Dina Harith Shaker2
1
Nanotechnology and Advanced Material Research Center, University of Technology, Baghdad, Iraq
2
Department of Electromechanical Engineering, University of Technology, Baghdad, Iraq

Article Info ABSTRACT

Article history: One of the problems that need to be solved is the difference in the type of
nutrition from the load. The feeding may be from a constant current source
Received Apr 23, 2022 such as batteries and solar cells, and there are alternating current sources such
Revised Jul 31, 2022 as diesel machines, wind energy, and various power plants. All of these
Accepted Aug 28, 2022 sources need electronic power devices that help convert and regulate the
control and control of the type of feeding on the one hand and its amount on
the other. From here, we show the size of the challenge occupied by electronic
Keywords: power transformers, as they are considered the solution to many problems of
transmission, distribution, and feeding systems for different loads. The current
1-phase rectifier study sheds light on one of the types of electronic power systems, which is
Full wave rectifier unified. Choosing and suggesting a set of single-phase unifying circuits to
Half-wave rectifier conduct simulations and come up with results that are analyzed to show the
Power electronic device function of the non-electronic modulators. In the current simulation, tests were
carried out for a group of circuits that need direct current (DC) power, and
their available source of supply is an alternating current source to different
departments to access a set of data that enables researchers to conduct
appropriate analyzes to perform them, by discussing those results.
This is an open access article under the CC BY-SA license.

Corresponding Author:
Salam Waley Shneen
Nanotechnology and advanced material research Center, University of Technology
Al Senaha St, Baghdad, Iraq
Email: [email protected]

1. INTRODUCTION
Electronic power devices are important in many applications, which is why they are a source of
interest for researchers with specialists [1]–[3]. Electronic power devices are of four forms, including changing
the type of supply from continuous to alternating and vice versa, and second from a fixed source to a variable
[4]–[6]. The first is called the unified, which converts from alternating current to continuous single-phase or
three-phase [7]–[9]. The second inverter, which is the opposite of the unified, converts the continuous into
alternating [10]–[12]. The third is a constant current transformer and works on obtaining a variable supply from
a fixed source [13]–[15]. The fourth is the same as the third, but with a different type of current, it is a constant
alternating current (AC) transformer to a variable [16]–[19]. All types can be standardized full waves or unified
half waves [20]–[22]. Electronic power devices are important as they are used in various applications such as
household and industrial appliances and others that need to be fed a constant current and with an alternating
current supply source [23]–[25]. It is necessary for the specialists to see the behavior of the various unified
circuits [26]–[28]. Therefore, researchers focused on all types, including single-phase, and there is also another
three-phase type [29]–[31].
In the current simulation, verify the possibility of using the computer program to test more types that
represent a uniform full wave and half wave. Current simulation using MATLAB/Simulink program for a

Journal homepage: http://ijaas.iaescore.com

254  ISSN: 2252-8814

single-phase modulator that converts alternating current to direct current (DC). It is proposed to simulate this
type with a 314 V source and a frequency of 50 Hz. The proposed circuits for simulation are firstly, half wave
unified and secondly” full wave unified. Electronic switches and it is called unified uncontrolled using diode
again and again unified controller using thyristor. The simulation depends on the unified test in three cases
from the load end, resistance load 30 ohm, 40 ohm, and 50 ohm.
The results are in a form. Therefore, it can be said in the cases included in the simulation. First, “a
unified half-wave without a controller, the number of which is three, it is a unified half-wave without a
controller using an electronic switch, the diode, and the circuit load is (resistance, at 30 ohm, 40 ohm, and 50
ohm). Secondly, a unified half-wave with a controller and its number three is a unified half-wave controlled
by a thyristor electronic switch and the circuit load is (resistance, at 30 ohm, 40 ohm, and 50 ohm). Third, a
unified full-wave without a controller, and the three number are unified half-wave without a controller using
an electronic switch, the diode, and the circuit load is (resistance, at 30 ohm, 40 ohm, and 50 ohm). Fourth, a
unified full-wave with a controller, and the three are unified half-wave with a controller using an electronic
switch, a thyristor and circuit load are (resistance, at 30 ohm, 40 ohm, and 50 ohm).

2. SIMULATION AND MATHEMATICAL REPRESENTATION

Power electronic devices (PED) are classified into four types in terms of conversion. A transformer is
called an inverter, which has a continuous input and an alternating output [32]–[34]. Another has an alternating
input and a continuous output called the unified. There are transformers for the same supply and output, both
continuous or alternating. All the mentioned types are used using electronic switches such as diode, transistor
and thyristor. Some of them are single-phase and three-phase [29], [35], [36]. Their selection depends on the
type of supply, type of load, and the required amount of frequency, current and voltage. Electronic transformers
are built on two types, including half-wave and full-wave [37]–[40].
The simulation is carried out for a full-wave and half-wave unifier, which can be represented
mathematically by (1) to (12), which can be represented in Figures 1-4. Equation (1) is root mean square of
output voltage (Vrms).

𝑇 0.5
𝑉𝑟𝑚𝑠 = {𝑇1 ∫0 𝑉 2 (𝑡)𝑑𝑡} (1)

Equation (2) is root mean square of output current (Irms).

𝑇 0.5
𝐼𝑟𝑚𝑠 = {𝑇1 ∫0 𝐼 2 (𝑡)𝑑𝑡} (2)

Equation (3) is average of voltage (Vavg).

𝑇
𝑉𝑎𝑣𝑔 = 𝑇1 ∫0 𝑉(𝑡)𝑑𝑡 (3)

Equation (4) is average of current (Iavg).

𝑇
𝐼𝑎𝑣𝑔 = 𝑇1 ∫0 𝐼(𝑡)𝑑𝑡 (4)

Equation (5) is root mean square of input power (Pac).

𝑃𝑎𝑐 = 𝑉𝑟𝑚𝑠 . 𝐼𝑟𝑚𝑠 (5)

Equation (6) is average of output power (Pdc).

𝑃𝑑𝑐 = 𝑉𝑎𝑣𝑔 . 𝐼𝑎𝑣𝑔 (6)

Equation (7) is efficiency (η).

𝜂 = 𝑃𝑃𝑎𝑐=𝑉𝑉𝑟𝑚𝑠 .𝐼𝑟𝑚𝑠
𝑎𝑣𝑔 .𝐼𝑎𝑣𝑔
(7)
𝑑𝑐

Equation (8) is ripple factor (RF).

Int J Adv Appl Sci, Vol. 11, No. 3, September 2022: 253-262
Int J Adv Appl Sci ISSN: 2252-8814  255
𝑉𝑎𝑐
𝑅𝐹 = (8)
𝑉𝑑𝑐

Equation (9) is form factor (FF).

𝑉𝑟𝑚𝑠
𝐹𝐹 = (9)
𝑉𝑎𝑣𝑔

Equation (10) is harmonic factor (HF).

2 0.5
𝐼𝑠1
𝐻𝐹 = [( ⁄𝐼 ) − 1]
𝑠
(10)
Equation (11) is crest factor (CF).
𝐼𝑠(𝑝𝑒𝑎𝑘)
𝐶𝐹 = (11)
𝐼𝑠

Equation (12) is power factor (PF) [41]–[44].

𝐼𝑠1
𝑃𝐹 = ⁄𝐼 𝑐𝑜𝑠∅ (12)
𝑠

In Figure 1 show 1-ph of uncontrolled for half wave rectifier (H.W.R) by using one diode with R load.
In Figure 2 show 1-ph of controlled for H.W.R by using one thyristor with R load. In Figure 3 show 1-ph of
uncontrolled for full wave rectifier (F.W.R) by using four diode with R load. In Figure 4 show 1-ph of
controlled for F.W.R by using four thyristor with R load.

Figure 1. 1-ph of uncontrolled for H.W.R with R Figure 2. 1-ph of controlled for H.W.R with R load
load

Figure 3. 1-ph of uncontrolled for F.W.R with R Figure 4. 1-ph of controlled for F.W.R with R load
load

Simulation model of 1-phase PWM rectifier by using MATLAB/Simulink (Salam Waley Shneen)
256  ISSN: 2252-8814

3. MODELLING AND SIMULATION RESULTS

To conduct the simulation, a model was proposed for each circuit representing a unified full wave or
a unified half wave with the parameters of the load for each case and the supply source voltage, frequency, and
resistance in tables for all cases for which the simulation was proposed. Using the simulation of these types,
the results can be shown as in the tables and figures, which shows the possibility of obtaining verification
results and shows the work of the rectifier in obtaining a constant current from an alternating current source to
feed the load. Simulation results can be documented in tables and figures and under different headings
according to the type of rectifier used, as in the following figures and tables. Table 1 shows values for parameter
of models.

Table 1. Values for parameter of models

Parameter Sym poles Values Units
I/P Voltage Vin 220 volts
I/P Frequency Fin 50 Hz
Resistance R 30, 40, 50 Ω

In Figure 5 show three models for 1-phase uncontrolled H.W.R that use in this simulation,
Figures 5(a) at load 30 ohm, 5(b) at load 40 ohm, and 5(c) at load 50 ohm. In Figure 6 show three models for
1-phase controller H.W.R that use in this simulation, Figures 6(a) at load 30 ohm, 6(b) at load 40 ohm, and
6(c) at load 50 ohm. In Figure 7 show three models for 1-phase uncontrolled F.W.R that use in this simulation,
Figures 7(a) at load 30 ohm, 7(b) at load 40 ohm, and 7(c) at load 50 ohm. In Figure 8 show three models for
1-phase controller F.W.R that use in this simulation, Figure 8(a) at load 30 ohm, 8(b) at load 40 ohm, and 8(c)
at load 50 ohm.

(a)

(b)

(c)

Figure 5. 1-ph uncontrolled H.W.R: (a) load 30 ohm, (b) load 40 ohm, and (c) load 50 ohm

Int J Adv Appl Sci, Vol. 11, No. 3, September 2022: 253-262
Int J Adv Appl Sci ISSN: 2252-8814  257

(a)

(b)

(c)

Figure 6. 1-ph controlled H.W.R: (a) load 30 ohm, (b) load 40 ohm, and (c) load 50 ohm

(a) (b)

(c)

Figure 7. 1-ph uncontrolled F.W.R: (a) load 30 ohm, (b) load 40 ohm, and (c) load 50 ohm

Simulation model of 1-phase PWM rectifier by using MATLAB/Simulink (Salam Waley Shneen)
258  ISSN: 2252-8814

(a)

(b)

(c)

Figure 8. 1-ph controlled F.W.R: (a) load 30 ohm, (b) load 40 ohm, and (c) load 50 ohm

In Figure 9 show three states for response of 1-phase uncontrolled H.W.R that use in this simulation,
Figures 9(a) at load 30 ohm, 9(b) at load 40 ohm, and 9(c) at load 50 ohm. In Figure 10 show three states for
response of 1-phase controller H.W.R that use in this simulation, Figures 10(a) at load 30 ohm, 10(b) at load
40 ohm, and 10(c) at load 50 ohm. In Figure 11 show three states for response of 1-phase uncontrolled F.W.R
that use in this simulation, Figures 11(a) at load 30 ohm, 11(b) at load 40 ohm, and 11(c) at load 50 ohm.
In Figure 12 show three states for response of 1-phase controller F.W.R that use in this simulation,
Figures 12(a) at load 30 ohm, 12(b) at load 40 ohm, and 12(c) at load 50 ohm.

Int J Adv Appl Sci, Vol. 11, No. 3, September 2022: 253-262
Int J Adv Appl Sci ISSN: 2252-8814  259

(a) (b)

(c)
Figure 9. MATLAB/Simulink response of 1-phase uncontrolled H.W.R with R load: (a) load 30 ohm, (b)
load 40 ohm, and (c) load 50 ohm

(a) (b)

(c)
Figure 10. MATLAB/Simulink response of 1-phase controlled H.W.R with R load: (a) load 30 ohm, (b) load
40 ohm, and (c) load 50 ohm

Simulation model of 1-phase PWM rectifier by using MATLAB/Simulink (Salam Waley Shneen)
260  ISSN: 2252-8814

(a) (b)

(c)
Figure 11. MATLAB/Simulink response of 1-phase uncontrolled F.W.R with R load: (a) load 30 ohm, (b)
load 40 ohm, and (c) load 50 ohm

(a) (b)

(c)
Figure 12. MATLAB/Simulink response of 1-phase controller F.W.R with R load: (a) load 30 ohm, (b) load
40 ohm, and (c) load 50 ohm

Int J Adv Appl Sci, Vol. 11, No. 3, September 2022: 253-262
Int J Adv Appl Sci ISSN: 2252-8814  261

In Table 2 show four states uncontrolled H.W.R, controller H.W.R, uncontrolled F.W.R, and
controller F.W.R. In all states whenever change load, the voltage is constant but the current was change.
Increase the value of load give decrease in current. For example, in first state uncontrolled H.W.R, Vavrg was
constant at 69.6 V, Vrms (V) was constant at 109.5 v with load 30, 40, and 50 ohm. Also, the current was change
with load, Irms was 3.5 A at 30 ohm, 2.7 at 40 ohm, and 2.1 at 50 ohm and I avrg was 2.3 A at 30 ohm, 1.7 at 40
ohm, and 1.3 at 50 ohm.

Table 2. Behavior of 1-phase of AC-DC rectifier

Type of AC-DC converter RL (ohm) Vavrg Iavrg Vrms (V) Irms (A)
Uncontrolled H.W.R 30 69.6 3.5 109.5 2.3
40 69.6 2.7 109.5 1.7
50 69.6 2.1 109.5 1. 3
Controlled H.W.R 30 65.9 3.6 108.3 2.1
40 65.9 2.7 108.3 1.6
50 65.9 2.1 108.3 1.3
Uncontrolled F.W.R 30 138.5 4.615 154.1 5.137
40 138.5 3.461 154.1 3.853
50 138.5 2.769 154.1 3.082
Controlled F.W.R 30 126.5 4.217 157.1 5.238
40 126.5 3.163 157.1 3.929
50 126.5 2.53 157.1 3.143

4. CONCLUSION
After conducting the simulation, a number of conclusions were reached as a result of obtaining results
stating that the voltage is stable with the change of load, but the current changes. We suggest the use of pulse
width control systems and traditional and expert control systems to adjust the value of the current as future
works. Where the results proved the possibility of converting from alternating current to continuous current on
the one hand and controlling the current and voltage with the change of load on the other hand, which enabled
us to reach how to employ the uniters in different power systems. The simulation also showed the difference
in the voltage value according to the type of unifier used. The current study showed, through computer
simulation, the possibility of using MATLAB/Simulink to verify the work of electronic circuits in a short time.

REFERENCES
[1] T. G. Habetler, “A space vector-based rectifier regulator for AC/DC/AC converters,” IEEE Trans. Power Electron., vol. 8, no. 1,
pp. 30–36, Jan. 1993, doi: 10.1109/63.208497.
[2] K. Zhang, “Online Fault Diagnosis for Single-Phase PWM Rectifier Using Data-Driven Method,” CPSS Trans. Power Electron.
Appl., vol. 7, no. 1, pp. 49–57, Mar. 2022, doi: 10.24295/CPSSTPEA.2022.00005.
[3] Z. Gong, D. Huang, L. Ma, N. Qin, and H. U. K. Jadoon, “Grid voltage sensor fault‐tolerant control for single‐phase two‐level
PWM rectifier,” IET Electr. Power Appl., vol. 16, no. 7, pp. 776–788, Jul. 2022, doi: 10.1049/elp2.12103.
[4] R. Bibave, P. Thokal, R. Hajare, A. Deulkar, P. William, and A. T. Chandan, “A Comparative Analysis of Single Phase to Three
Phase Power Converter for Input Current THD Reduction,” in 2022 International Conference on Electronics and Renewable
Systems (ICEARS), Mar. 2022, pp. 325–330, doi: 10.1109/ICEARS53579.2022.9752161.
[5] S. W. Shneen, “Advanced Optimal for Power-Electronic Systems for the Grid Integration of Energy Sources,” Indones. J. Electr.
Eng. Comput. Sci., vol. 1, no. 3, p. 543, Mar. 2016, doi: 10.11591/ijeecs.v1.i3.pp543-555.
[6] H. Zhou, L. Kang, X. Duan, and M. Zhao, “Secondary ripple suppression strategy for a single-phase PWM rectifier based on
constant frequency current predictive control,” IEICE Trans. Electron., p. 2021ESP0004, 2022, doi:
10.1587/transele.2021ESP0004.
[7] L. A. Garcia-Reyes, A. Beltrán-Telles, F. Bañuelos-Ruedas, M. Reta-Hernández, J. M. Ramírez-Arredondo, and R. Silva-Casarín,
“Level-Shift PWM Control of a Single-Phase Full H-Bridge Inverter for Grid Interconnection, Applied to Ocean Current Power
Generation,” Energies, vol. 15, no. 5, p. 1644, Feb. 2022, doi: 10.3390/en15051644.
[8] J. Deng, Y. Lei, J.-S. Kang, and M. Yu, “A Harmonic Current Suppression Method for Single-Phase PWM Rectifier Based on
Feedback Linearization,” in 2022 International Conference on Power Energy Systems and Applications (ICoPESA), Feb. 2022, pp.
90–95, doi: 10.1109/ICoPESA54515.2022.9754411.
[9] Y. Zhu, Z. Wang, C. Wang, Y. Zhu, and X. Cao, “A Novel Improved Coordinate Rotated Algorithm for PWM Rectifier THD
Reduction,” Electronics, vol. 11, no. 9, p. 1435, Apr. 2022, doi: 10.3390/electronics11091435.
[10] L. Peng, L. Ma, W. Song, and H. Liu, “A Simple Model Predictive Instantaneous Current Control for Single-Phase PWM Converters
in Stationary Reference Frame,” IEEE Trans. Power Electron., vol. 37, no. 7, pp. 7629–7639, Jul. 2022, doi:
10.1109/TPEL.2022.3141793.
[11] S. W. Shneen, C. Mao, and D. Wang, “Advanced Optimal PSO, Fuzzy and PI Controller with PMSM and WTGS at 5Hz Side of
Generation and 50Hz Side of Grid,” Int. J. Power Electron. Drive Syst., vol. 7, no. 1, p. 173, Mar. 2016, doi:
10.11591/ijpeds.v7.i1.pp173-192.
[12] M. Arehpanahi and A. M. Entekhabi, “A New Technique for Online Open Switch Fault Detection and Location in Single-phase
Pulse Width Modulation Rectifier,” Int. J. Eng., vol. 35, no. 9, pp. 1759–1764, 2022, doi: 10.5829/IJE.2022.35.09C.12.
[13] M. Chaker et al., “Design and Simulation of High Input Power Factor AC/DC Converter Based on a Single-Phase PWM Rectifier,”
in The Proceedings of the International Conference on Electrical Systems & Automation, Singapore: Springer Singapore, 2022, pp.
81–90.
Simulation model of 1-phase PWM rectifier by using MATLAB/Simulink (Salam Waley Shneen)
262  ISSN: 2252-8814

[14] R. Sharma, P. Sharma, D. Nagaria, and A. Srivastava, “Active control of ripple energy in single-phase pulse width modulated
rectifier,” Int. J. Syst. Assur. Eng. Manag., vol. 13, no. 2, pp. 713–720, Apr. 2022, doi: 10.1007/s13198-021-01333-2.
[15] O. Stihi and Boon-Teck Ooi, “A single-phase controlled-current PWM rectifier,” IEEE Trans. Power Electron., vol. 3, no. 4, pp.
453–459, Oct. 1988, doi: 10.1109/63.17967.
[16] N. Ashraf et al., “Investigation of the Power Quality Concerns of Input Current in Single-Phase Frequency Step-Down Converter,”
Appl. Sci., vol. 12, no. 7, p. 3663, Apr. 2022, doi: 10.3390/app12073663.
[17] V. Safonov and M. Dziuba, “Voltage regulation and phase quantity increase of two high-power 12-phase rectifiers,” Int. J. Power
Electron. Drive Syst., vol. 10, no. 3, pp. 1454–1460, 2019, doi: 10.11591/ijpeds.v10.i3.1454-1460.
[18] B. Singh, B. N. Singh, A. Chandra, K. Al-Haddad, A. Pandey, and D. P. Kothari, “A review of single-phase improved power quality
ac~dc converters,” IEEE Trans. Ind. Electron., vol. 50, no. 5, pp. 962–981, Oct. 2003, doi: 10.1109/TIE.2003.817609.
[19] A. Taybi, A. Tajmouati, J. Zbitou, A. Errkik, M. Latrach, and L. El Abdellaoui, “A new design of high output voltage rectifier for
rectenna system at 2.45 GHz,” Indones. J. Electr. Eng. Comput. Sci., vol. 13, no. 1, p. 226, Jan. 2019, doi:
10.11591/ijeecs.v13.i1.pp226-234.
[20] S. W. Shneen, “Advanced Optimal For Three Phase Rectifier in Power Electronic System,” Indones. J. Electr. Eng. Comput. Sci.,
vol. 11, no. 3, p. 821, Sep. 2018, doi: 10.11591/ijeecs.v11.i3.pp821-830.
[21] M. M. S. Khan, M. S. Arifin, M. R. T. Hossain, M. A. Kabir, A. H. Abedin, and M. A. Choudhury, “Input switched single phase
buck and buck-boost AC-DC converter with improved power quality,” in 2012 7th International Conference on Electrical and
Computer Engineering, Dec. 2012, pp. 189–192, doi: 10.1109/ICECE.2012.6471517.
[22] A. Taybi, A. Tajmouati, J. Zbitou, A. Errkik, M. Latrach, and L. El Abdellaoui, “A New Configuration of A High Output Voltage
2.45 GHz Rectifier For Wireless Power Transmission Applications,” TELKOMNIKA (Telecommunication Comput. Electron.
Control., vol. 16, no. 5, p. 1939, Oct. 2018, doi: 10.12928/telkomnika.v16i5.9707.
[23] R. Miyauchi, K. Tanno, and H. Tamura, “New active diode with bulk regulation transistors and its application to integrated voltage
rectifier circuit,” Int. J. Electr. Comput. Eng., vol. 9, no. 2, p. 902, Apr. 2019, doi: 10.11591/ijece.v9i2.pp902-908.
[24] S. W. Shneen, M. A. A. Hussein, J. A. Kadhum, and S. M. Ali, “Application of LFAC (16 2/3Hz) for electrical power transmission
system: a comparative simulation study,” TELKOMNIKA (Telecommunication Comput. Electron. Control., vol. 17, no. 2, p. 1055,
Apr. 2019, doi: 10.12928/telkomnika.v17i2.10353.
[25] R. Ghosh and G. Narayanan, “A Simple Analog Controller for Single-Phase Half-Bridge Rectifier,” IEEE Trans. Power Electron.,
vol. 22, no. 1, pp. 186–198, Jan. 2007, doi: 10.1109/TPEL.2006.886621.
[26] S. W. Shneen, “BBO Tuned FLC for Three Phase Rectifier,” Int. Res. J. Adv. Eng. Sci., vol. 3, no. 1, pp. 262–267, 2018, [Online].
Available: http://irjaes.com/wp-content/uploads/2020/10/IRJAES-V3N1P716Y18.pdf.
[27] K. Kumar, K. R. Prabhu, N. Ramesh Babu, and P. Sanjeevikumar, “A Novel Six-Switch Power Converter for Single-Phase Wind
Energy System Applications,” in Advances in Smart Grid and Renewable Energy, 2018, pp. 267–275.
[28] R. Griñó, E. Fossas, and D. Biel, “Sliding mode control of a full-bridge unity power factor rectifier,” in Nonlinear and Adaptive
Control, Berlin, Heidelberg: Springer Berlin Heidelberg, 2002, pp. 139–148.
[29] A. N. F. Asli and Y. C. Wong, “3.3V DC output at -16dBm sensitivity and 77% PCE rectifier for RF energy harvesting,” Int. J.
Power Electron. Drive Syst., vol. 10, no. 3, p. 1398, Sep. 2019, doi: 10.11591/ijpeds.v10.i3.pp1398-1409.
[30] S. W. Shneen, “Utilization of DC motor-AC generator system to convert the solar direct current into 220v alternating current,” Int.
J. Comput. Appl. Sci., vol. 5, no. 3, pp. 391–396, 2018.
[31] N. A. Ahmed, “Modeling and simulation of ac–dc buck-boost converter fed dc motor with uniform PWM technique,” Electr. Power
Syst. Res., vol. 73, no. 3, pp. 363–372, Mar. 2005, doi: 10.1016/j.epsr.2004.08.010.
[32] N. Mohamed, T. Hamza, and G. Brahim, “Novel DTC induction machine drive improvement using controlled rectifier for DC
voltage tuning,” Int. J. Power Electron. Drive Syst., vol. 10, no. 3, p. 1223, Sep. 2019, doi: 10.11591/ijpeds.v10.i3.pp1223-1228.
[33] R. Sasikala and R. Seyezhai, “Review of AC-DC power electronic converter topologies for power factor correction,” Int. J. Power
Electron. Drive Syst., vol. 10, no. 3, p. 1510, Sep. 2019, doi: 10.11591/ijpeds.v10.i3.pp1510-1519.
[34] R. Baharom and M. N. Seroji, “Dynamic analysis of the high-power factor three-phase AC to DC converter using current injection
hybrid resonant Technique,” Int. J. Power Electron. Drive Syst., vol. 10, no. 1, p. 538, Mar. 2019, doi:
10.11591/ijpeds.v10.i1.pp538-547.
[35] S. W. Shneen, “Advanced Optimal For PV system coupled with PMSM,” Indones. J. Electr. Eng. Comput. Sci., vol. 1, no. 3, p.
556, Mar. 2016, doi: 10.11591/ijeecs.v1.i3.pp556-565.
[36] A. Bouafassa, L. Rahmani, and S. Mekhilef, “Design and real time implementation of single phase boost power factor correction
converter,” ISA Trans., vol. 55, pp. 267–274, Mar. 2015, doi: 10.1016/j.isatra.2014.10.004.
[37] G. Sarowar and M. A. Hoque, “High Efficiency Single Phase Switched Capacitor AC to DC Step Down Converter,” Procedia -
Soc. Behav. Sci., vol. 195, pp. 2527–2536, Jul. 2015, doi: 10.1016/j.sbspro.2015.06.437.
[38] A. K. Tyagi, MATLAB and SIMULINK for Engineers. OUP Higher Education Division, 2011.
[39] N. Susheela and P. S. Kumar, “Performance evaluation and comparison of diode clamped multilevel inverter and hybrid inverter
based on PD and APOD modulation techniques,” Int. J. Adv. Appl. Sci., vol. 8, no. 2, p. 143, Jun. 2019, doi:
10.11591/ijaas.v8.i2.pp143-153.
[40] S. W. Shneen, D. H. Shaker, and F. N. Abdullah, “Simulation model of PID for DC-DC converter by using MATLAB,” Int. J.
Electr. Comput. Eng., vol. 11, no. 5, p. 3791, Oct. 2021, doi: 10.11591/ijece.v11i5.pp3791-3797.
[41] R. K. Bhukya and P. S. Kumar, “Simplified down sampling factor based modified SVPWM technique for cascaded inverter fed
induction motor drive,” Int. J. Adv. Appl. Sci., vol. 9, no. 1, p. 20, Mar. 2020, doi: 10.11591/ijaas.v9.i1.pp20-26.
[42] H. K. Khleaf, A. K. Nahar, and A. S. Jabbar, “Intelligent control of DC-DC converter based on PID-neural network,” Int. J. Power
Electron. Drive Syst., vol. 10, no. 4, p. 2254, Dec. 2019, doi: 10.11591/ijpeds.v10.i4.pp2254-2262.
[43] S. W. Shneen and G. A. Aziz, “Simulation model of 3-phase PWM rectifier by using MATLAB/Simulink,” Int. J. Electr. Comput.
Eng., vol. 11, no. 5, p. 3736, Oct. 2021, doi: 10.11591/ijece.v11i5.pp3736-3746.
[44] S. W. Shneen, R. T. Ahmedhamdi, and M. K. S. Al-Ghezi, “A-review of Simulink for single-phase rectifier,” Int. J. Adv. Appl. Sci.,
vol. 11, no. 1, p. 76, Mar. 2022, doi: 10.11591/ijaas.v11.i1.pp76-87.

Int J Adv Appl Sci, Vol. 11, No. 3, September 2022: 253-262