Honeywell Process Solution

Honeywell RC500
Software Installation User's Guide
RC-DCX210
R200
November 2011

Release 200
Honeywell
 Notices and Trademarks
Copyright 2011 by Honeywell International Sárl.
Release 200 November 2011

While this information is presented in good faith and believed to be accurate, Honeywell disclaims
the implied warranties of merchantability and fitness for a particular purpose and makes no
express warranties except as may be stated in its written agreement with and for its customers.

In no event is Honeywell liable to anyone for any indirect, special or consequential damages. The
information and specifications in this document are subject to change without notice.

Honeywell, PlantScape, Experion PKS, and TotalPlant are registered trademarks of Honeywell
International Inc.

Other brand or product names are trademarks of their respective owners.

Honeywell Process Solutions

1860 W. Rose Garden Lane
Phoenix, AZ 85027 USA
1-800 822-7673

ii Honeywell RC500 Software Installation User's Guide R200

Honeywell November 2011
 About This Document
This document describes how to install Honeywell RC500 I/O Tool Kit and ISaGRAF Open. It
also describes the procedure to register the licenses for the Tool Kit and ISaGRAF Open.
This documentation is intended for the following audience:
• System Engineers who would configure the Honeywell RC500 modules, create associated
applications, and operate the run-time Honeywell RC500 modules.
• Field Engineers who would install and maintain Honeywell RC500 modules.

Release Information
Document Name Document ID Release Publication
Number Date

Honeywell RC500 Software Installation User's RC-DCX210 200 November

Guide - SIUG 2011

References
The following list identifies all documents that may be sources of reference for material discussed
in this publication.

Document Title

Honeywell RC500 Ethernet I/O-2 User’s Guide

Honeywell RC500 MVACONTRL MVBCONTRL RTU User’s Guide

Honeywell RC500 SCONTRL RTU User’s Guide

Honeywell RC500 ISaGRAF User’s Guide

Honeywell RC500 Switch User’s Guide

R200 Honeywell RC500 Software Installation User's Guide iii

November 2011 Honeywell
Support and Other Contacts

Support and Other Contacts

United States and Canada
Contact: Honeywell Solution Support Center
Phone: 1-800-822-7673
Calls are answered by dispatcher between 6:00 am and 4:00 pm
Mountain Standard Time. Emergency calls outside normal working hours
are received by an answering service and returned within one hour.
Fascimile: 1-973-455-5000
Mail: Honeywell TAC, MS L17
1860 W. Garden Lane
Phoenix, AZ, 85027 USA

Europe, Middle East, and Africa (EMEA)

Contact: Honeywell TAC-EMEA
Phone: +32-2-728-2345
Fascimile: +32-2-728-2696
Mail: TAC-BE02
Hermes Plaza
Hermeslaan, 1H
B-1831 Diegem, Belgium

Pacific
Contact: Honeywell Global TAC – Pacific
Phone: 1300-364-822 (toll free within Australia)
+61-8-9362-9559 (outside Australia)
Fascimile: +61-8-9362-9564
Mail: Honeywell Limited Australia
5 Kitchener Way
Burswood 6100, Western Australia
Email: [email protected]

India
Contact: Honeywell Global TAC – India
Phone: +91-20- 6603-9400
Fascimile: +91-20- 6603-9800
Mail: Honeywell Automation India Ltd
56 and 57, Hadapsar Industrial Estate
Hadapsar, Pune –411 013, India
Email: [email protected]

iv Honeywell RC500 Software Installation User's Guide R200

Honeywell November 2011
 Support and Other Contacts

Korea
Contact: Honeywell Global TAC – Korea
Phone: +82-80-782-2255 (toll free within Korea)
Fascimile: +82-2-792-9015
Mail: Honeywell Co., Ltd
4F, Sangam IT Tower
1590, DMC Sangam-dong, Mapo-gu
Seoul, 121-835, Korea
Email: [email protected]

People’s Republic of China

Contact: Honeywell Global TAC – China
Phone: +86- 21-2219-6888
800-820-0237
400-820-0386
Mail: Honeywell (China) Co., Ltd
33/F, Tower A, City Center, 100 Zunyi Rd.
Shanghai 200051, People’s Republic of China
Email: [email protected]

Singapore
Contact: Honeywell Global TAC – South East Asia
Phone: +65-6580-3500
Fascimile: +65-6580-3501
+65-6445-3033
Mail: Honeywell Private Limited
Honeywell Building
17, Changi Business Park Central 1
Singapore 486073
Email: [email protected]

Taiwan
Contact: Honeywell Global TAC – Taiwan
Phone: +886-7-536-2567
Fascimile: +886-7-536-2039
Mail: Honeywell Taiwan Ltd.
17F-1, No. 260, Jhongshan 2nd Road.
Cianjhen District
Kaohsiung, Taiwan, ROC
Email: [email protected]

R200 Honeywell RC500 Software Installation User's Guide v

November 2011 Honeywell
Support and Other Contacts

Japan
Contact: Honeywell Global TAC – Japan
Phone: +81-3-6730-7160
Fascimile: +81-3-6730-7228
Mail: Honeywell Japan Inc.
New Pier Takeshiba, South Tower Building,
20th Floor, 1-16-1 Kaigan, Minato-ku,
Tokyo 105-0022, Japan
Email: [email protected]

Elsewhere
Call your nearest Honeywell office.

World Wide Web

Honeywell Solution Support Online:

http://www.honeywell.com/ps

Training Classes
Honeywell Automation College:

http://www.automationcollege.com

vi Honeywell RC500 Software Installation User's Guide R200

Honeywell November 2011
 Symbol Definitions

Symbol Definitions
The following table lists those symbols used in this document to denote certain conditions.

Symbol Definition

ATTENTION: Identifies information that requires special

consideration.

TIP: Identifies advice or hints for the user, often in terms of

performing a task.

REFERENCE -EXTERNAL: Identifies an additional source of

information outside of the bookset.

REFERENCE - INTERNAL: Identifies an additional source of

information within the bookset.

CAUTION Indicates a situation which, if not avoided, may result in equipment

or work (data) on the system being damaged or lost, or may result in
the inability to properly operate the process.

CAUTION: Indicates a potentially hazardous situation which, if not

avoided, may result in minor or moderate injury. It may also be used
to alert against unsafe practices.

CAUTION symbol on the equipment refers the user to the product

manual for additional information. The symbol appears next to
required information in the manual.

WARNING: Indicates a potentially hazardous situation, which, if not

avoided, could result in serious injury or death.

WARNING symbol on the equipment refers the user to the product

manual for additional information. The symbol appears next to
required information in the manual.

WARNING, Risk of electrical shock: Potential shock hazard where

HAZARDOUS LIVE voltages greater than 30 Vrms, 42.4 Vpeak, or
60 VDC may be accessible.

R200 Honeywell RC500 Software Installation User's Guide vii

November 2011 Honeywell
Symbol Definitions

Symbol Definition

ESD HAZARD: Danger of an electro-static discharge to which

equipment may be sensitive. Observe precautions for handling
electrostatic sensitive devices.

Protective Earth (PE) terminal: Provided for connection of the

protective earth (green or green/yellow) supply system conductor.

Functional earth terminal: Used for non-safety purposes such as

noise immunity improvement. NOTE: This connection shall be
bonded to Protective Earth at the source of supply in accordance
with national local electrical code requirements.

Earth Ground: Functional earth connection. NOTE: This

connection shall be bonded to Protective Earth at the source of
supply in accordance with national and local electrical code
requirements.

Chassis Ground: Identifies a connection to the chassis or frame of

the equipment shall be bonded to Protective Earth at the source of
supply in accordance with national and local electrical code
requirements.

viii Honeywell RC500 Software Installation User's Guide R200

Honeywell November 2011
 Contents

1. INTRODUCTION TO RC500 .........................................................11

1.1 RC500 overview ............................................................................................ 11
RC500 components ..................................................................................................12
1.2 RC500 compatibility with Experion ............................................................ 14

2. RC500 INSTALLATION ................................................................15

2.1 RC500 software installation components .................................................. 15
2.2 Software requirements for installing RC500 ............................................. 15
2.3 System requirements for installing RC500 ................................................ 16
2.4 Disabling antivirus software ....................................................................... 17
2.5 Protecting against antivirus software ........................................................ 18
Configuring antivirus software guidelines .................................................................18
Configuring McAfee VirusScan.................................................................................18
2.6 Installing Honeywell RC500 I/O Tool Kit .................................................... 19
2.7 Installing ISaGRAF Open ............................................................................. 20
2.8 Installing RC500 diagnostic display ........................................................... 22

3. POST-INSTALLATION TASKS ....................................................23

3.1 Registering Honeywell RC500 I/O Tool Kit license using CD-ROM drive23
3.2 Registering Honeywell RC500 I/O Tool Kit license manually .................. 25
3.3 Registering ISaGRAF Open license ........................................................... 28

4. SWITCH UTILITY INSTALLATION ...............................................31

4.1 Installing the Switch Utility.......................................................................... 31

5. RC500 MAINTENANCE ................................................................33

5.1 Overview of RC500 maintenance................................................................ 33
R200 Honeywell RC500 Software Installation User's Guide ix
November 2011 Honeywell
Contents

5.2 Taking backup of Honeywell RC500 I/O Tool Kit project ..........................33
5.3 Modifying Honeywell RC500 I/O Tool Kit components .............................34
5.4 Repairing Honeywell RC500 I/O Tool Kit components .............................35
5.5 Removing Honeywell RC500 I/O Tool Kit ...................................................36
5.6 Taking backup of ISaGRAF project.............................................................37
5.7 Removing ISaGRAF ......................................................................................38
5.8 Removing ISaGRAF Open license manager ..............................................39

x Honeywell RC500 Software Installation User's Guide R200

Honeywell November 2011
 1. Introduction to RC500
1.1 RC500 overview
RC500 modules in combination with Experion Supervisory Control and Data Acquisition
(SCADA) products provide an integrated solution for complex remote automation and
control needs. RC500 integrates with the Honeywell’s Experion using industry standard
protocols such as, Modbus and Distributed Network Protocol 3 (DNP3).

Figure 1 Experion and RC500 integration architecture

R200 Honeywell RC500 Software Installation User's Guide 11

November 2011 Honeywell
1. Introduction to RC500
1.1. RC500 overview

RC500 components
• Remote Terminal Unit (RTU)
− RC-SCONTRL
− RC-MVACONTRL
− RC-MVBCONTRL
• I/O module
− Ethernet I/O-2
• Honeywell RC500 I/O Tool Kit
• ISaGRAF Open

Remote Terminal Unit

RC500 offers the flexibility to choose the appropriate RTU model according to specific
application needs. The RTU variants are available based on the following features.
• Number of communication ports
• Memory
• System topology
• Protocol
• Type of input or output modules
The RC500 RTUs have the power of embedded Linux platform and are capable of
remote automation and control applications. They are designed to withstand the toughest
environment and consume less power, which makes them suitable to work using solar
power in remote applications.

12 Honeywell RC500 Software Installation User's Guide R200

Honeywell November 2011
 1. Introduction to RC500
1.1. RC500 overview

Table 1 RC500 RTU features

RC500 model Ports On-board I/O Memory

Ethern RS232 RS485 DI DO AI AO Datalogging Program DRAM
et Flash

RC- 5 2 1 2M 128M 64M

SCONTRL

RC- 1 2 2 12 4 8 2 512K 64M 32M

MVACONTRL

RC- 1 2 1 12 8 6 512K 64M 32M

MVBCONTRL

Ethernet I/O modules

RC500 Ethernet I/O-1/Ethernet I/O-2 and Windows software form a high performance
flexible I/O system. The I/O module is a DIN rail mounted I/O that provides direct field
wiring connections to different types of industry devices. It is connected to each
module’s base and setup choices are entered using the Honeywell RC500 I/O Tool Kit
software.

Honeywell RC500 I/O Tool Kit

The Honeywell RC500 I/O Tool Kit is an easy-to-use software package that is for
designing, configuring and maintaining the RC500 RTUs and Ethernet I/O modules. You
can assign tag names and configure modes of operation for the RC500 modules. The
optional feature sets provide exporting, datalogging, Linux features and other such
functionalities to the system. This software also enables easy configuration of IO
transfers between the RTUs.

ISaGRAF Open
ISAGRAF programming for RC500 provides IEC 61131 standard programming
languages such as, Sequential Function Chart (SFC), Ladder Diagram, Structured Text
(ST), Instruction List (IL), Function Block Diagram, and Flow Charting.
Graphical Programming: ISaGRAF combines ladder logic with powerful function
blocks to provide you the simplicity of a PLC, and the performance of a high-end process
controller.
Text Programming: IEC 61131 statement language uses simple text that is easy to learn
and maintain.

R200 Honeywell RC500 Software Installation User's Guide 13

November 2011 Honeywell
1. Introduction to RC500
1.2. RC500 compatibility with Experion

Multi-Tasking Organization: SFC organizes the programs into tasks or sequential steps.
Each SFC block may be a Ladder Diagram, Structured Text or Instruction list.
On-Line Program Changes: This helps to improve processes without waiting for
shutdowns. The ISaGRAF Workbench lets you make changes in program at any time.
Program Simulation: ISaGRAF has a program simulator that displays how your
program works before the actual startup. You can develop and debug your programs
quickly and easily, and then load them to a RC500 programmable node.
Direct RC500 tag references: The tag names from the Honeywell RC500 I/O Tool Kit
configuration appear automatically in ISaGRAF using Export option. These names are
reflected automatically in program logic and save significant programming time.

1.2 RC500 compatibility with Experion

Honeywell RC500 R200 is compatible with the following Experion version.
• Experion R400.1 with Server patch 2 Rev11

14 Honeywell RC500 Software Installation User's Guide R200

Honeywell November 2011
 2. RC500 Installation
2.1 RC500 software installation components
The following are the two software installation components.
• Honeywell RC500 I/O Tool Kit: It is an easy-to-use software package for
designing, configuring, and maintaining the RC500 RTUs and Ethernet I/O modules.
• ISaGRAF Open: ISAGRAF programming for RC500 provides IEC 61131 standard
programming languages such as Sequential Function Chart, Ladder Diagram,
Structured Text, Instruction List and Function Block Diagram, and Flow Charting.

2.2 Software requirements for installing RC500

Following are the software requirements to install Honeywell RC500 I/O Tool Kit and
ISaGRAF Open.

Software Honeywell RC500 I/O Tool ISaGRAF Open

requirements Kit

Installation media RC500 R200.1 CD RC500 R200.1 CD

Operating system Windows XP Windows XP with Service

Pack1 (SP1)

Antivirus software McAfee AV + VirusScan Engine + patch (8.7i + Engine 5400 +

Patch3)

Refer to the Honeywell Field Solutions Sales & Distribution web

site for more information about Honeywell-qualified antivirus
software.

For more information about configuring the antivirus software,

refer to the section, Protecting against antivirus software.

R200 Honeywell RC500 Software Installation User's Guide 15

November 2011 Honeywell
2. RC500 Installation
2.3. System requirements for installing RC500

2.3 System requirements for installing RC500

Following are the system requirements to install Honeywell RC500 I/O Tool Kit and
ISaGRAF Open.
System Honeywell RC500 I/O Tool ISaGRAF Open
requirements Kit

System • A computer with a • A computer with a Pentium

requirements Pentium or compatible or compatible processor,
processor and CD-ROM running at 166 MHz or faster
drive and CD-ROM drive
• 32 MB of RAM • 64 MB of RAM

• A hard disk with 100 MB • A hard disk with 200 MB of

of free space free space

16 Honeywell RC500 Software Installation User's Guide R200

Honeywell November 2011
 2. RC500 Installation
2.4. Disabling antivirus software

2.4 Disabling antivirus software

Before installing the software, disable the antivirus services to ensure proper installation
of the software.

ATTENTION
Ensure to restart your antivirus services after you completed the installation.

To disable the antivirus software, perform the following steps.

Step Action
1 Choose Start > All Programs > McAfee > VirusScan Console.
2 In the VirusScan Console window, choose Task > Properties.

The Access Protection Properties dialog box appears.

3 Clear Prevent McAfee services from being stopped check box.
4 Click Apply and then OK.
5 Close the VirusScan Console window.
6 Choose Start > Run.

The Run dialog box appears.

7 Type services.msc and click OK.

The Services window appears.

8 To disable the antivirus software, perform the following steps.
a) Right-click McAfee Framework Service and then click Properties.

The Properties dialog box appears.

b) In the General tab, click Stop.
c) In the Startup type box, select Disabled.
d) Click Apply and then OK.
9 Repeat steps 8a to 8d for McAfee McShield and McAfee Task Manager
Services.

R200 Honeywell RC500 Software Installation User's Guide 17

November 2011 Honeywell
2. RC500 Installation
2.5. Protecting against antivirus software

2.5 Protecting against antivirus software

Antivirus software must install on Honeywell RC500 I/O Tool Kit. Refer to the section,
Software requirements for installing RC500 for a list of antivirus programs qualified by
Honeywell.

Configuring antivirus software guidelines

Configure the antivirus software to exclude the directory and the subdirectories,
C:\Program Files\Honeywell from the virus scan.

Configuring McAfee VirusScan

McAfee VirusScan has the capability to scan scripts in HMIWeb displays. This
functionality can slow display call-up, as well as lead to memory leaks.

Step Action
1 Right-click the McAfee icon on the taskbar.
2 Click VirusScan Enterprise and VirusScan Console.

If the VirusScan console is not available in the notification area, then browse
to C:\Program Files\McAfee\VirusScan Enterprise\shcfg32.exe.
3 In the User Account Control dialog box, click Yes.
4 Double-click On-Access Scanner, and click the ScriptScan tab.
5 Clear Enable ScriptScan check box and click Apply.
6 Click All Processes in the left pane, and click the Detection tab.
7 Click Exclusions.
8 Click Add.
9 Click Browse and browse to the C:\Program Files\Honeywell directory, and
click OK.
10 Select Also exclude subfolders check box, and click OK to close the dialog
boxes.

18 Honeywell RC500 Software Installation User's Guide R200

Honeywell November 2011
 2. RC500 Installation
2.6. Installing Honeywell RC500 I/O Tool Kit

2.6 Installing Honeywell RC500 I/O Tool Kit

To install the Honeywell RC500 I/O Tool Kit, perform the following steps.

Step Action
1 Insert the RC500 R200.1 CD into the CD-ROM drive.
2 Browse to the folder containing the Honeywell RC500 I/O Tool Kit and
double-click the HoneywellIOTools.exe.

The Welcome to the Honeywell I/O Tool Kit Setup Wizard page appears.
3 Click Next.

The License Agreement page appears.

4 Click I Agree to accept the license agreement.

The Choose Components page appears.

5 Select the required components you want to install and then click Next.

The Choose Install Location page appears, displaying the default

destination folder.

If you want to change the default destination folder, click Browse to specify a
different destination folder.
6 Click Install.

After installation is complete, the Completing the Honeywell I/O Tool Kit
Setup Wizard page appears.
7 Click Finish.

R200 Honeywell RC500 Software Installation User's Guide 19

November 2011 Honeywell
2. RC500 Installation
2.7. Installing ISaGRAF Open

2.7 Installing ISaGRAF Open

ATTENTION
You must install the Honeywell RC500 I/O Tool Kit before installing ISaGRAF
Open.

To install ISaGRAF Open, perform the following steps.

Step Action
1 Insert the RC500 R200.1 CD into the CD-ROM drive.
2 Browse to the folder containing the ISaGRAF Open and double-click
isaopen.exe.

The Welcome to the InstallShield Wizard for License Manager page

appears.
3 Click Next.

The License Agreement page appears.

4 Click I accept the terms of the license agreement and then click Next.

A message appears displaying the information that the installation has

detected previously installed component and the installation shall proceed at
the following location: C:\Program Files\ISaGRAF Open\ISaGRAF.
5 Click OK.

The Welcome to the InstallShield Wizard for ISaGRAF Open page

appears.
6 Click Next.

The License Agreement page appears.

7 Click I accept the terms of the license agreement and then click Next.

A message appears informing you to add a shortcut to the product delivery

on your desktop.

20 Honeywell RC500 Software Installation User's Guide R200

Honeywell November 2011
 2. RC500 Installation
2.8. Installing RC500 diagnostic display

Step Action

The InstallShield Wizard Complete page appears.

8 Click Yes, I want to restart my computer now, if you want to restart the
computer.

or

Click No, I will restart my computer later.

ATTENTION
It is recommended to restart the computer after ISaGRAF
installation.
9 Click Finish.

R200 Honeywell RC500 Software Installation User's Guide 21

November 2011 Honeywell
2. RC500 Installation
2.8. Installing RC500 diagnostic display

2.8 Installing RC500 diagnostic display

To install RC500 diagnostic detail display, perform the following steps.

Step Action
1 Insert the RC500 R200.1 CD into the CD-ROM drive.
2 Copy “RTU_Display” folder to “C:\ProgramData\Honeywell\Experion
PKS\Client\Abstract.”

ATTENTION
Contents in RTU_Display folder are:
• Folder “Styles”

• Display files and subfolders

− RC500RTU_Navigation.htm and subfolder
"RC500RTU_Navigation_files”

− RC500RTUdiagnostic.htm and subfolder

"RC500RTUdiagnostic_files
− RC500RTUCommdiagnostic.htm and subfolder
"RC500RTUCommdiagnostic_files
− RC500RTUdatadiagnostic.htm and subfolder
"RC500RTUdatadiagnostic_files
− RC500DNP3RunTimeDisplay.htm and folder
RC500DNP3RunTimeDisplay _files
3 Launch the station.
4 Verify path “C:\ProgramData\Honeywell\Experion PKS\Client\Abstract”
mapped to the station display path.

22 Honeywell RC500 Software Installation User's Guide R200

Honeywell November 2011
 3. Post-installation Tasks
3.1 Registering Honeywell RC500 I/O Tool Kit license
using CD-ROM drive
ATTENTION
Ensure that Honeywell RC500 I/O Tool Kit is installed before you register the
Honeywell RC500 I/O Tool Kit license.

To register the Honeywell RC500 I/O Tool Kit license using the CD-ROM drive,
perform the following steps.
Step Action
1 Insert the RC500 R200.1 CD into the CD-ROM drive.

ATTENTION
If you do not have the Honeywell RC500 R200.1 CD, refer to
Registering Honeywell RC500 I/O Tool Kit license manually.
2 Choose Start > All Programs > Honeywell Tools > Honeywell RC500 I/O
Tool Kit .

The following message appears.

3 Click Yes to register.

The Registration Status dialog box appears.

4 Click Import.

The Select Registration File to Import dialog box appears.

R200 Honeywell RC500 Software Installation User's Guide 23

November 2011 Honeywell
3. Post-installation Tasks
3.2. Registering Honeywell RC500 I/O Tool Kit license manually

Step Action
5 Browse for the Honeywell.6rg file in the RC500 R200.1 CD and import it.

The following message appears.

24 Honeywell RC500 Software Installation User's Guide R200

Honeywell November 2011
 3. Post-installation Tasks
3.2. Registering Honeywell RC500 I/O Tool Kit license manually

3.2 Registering Honeywell RC500 I/O Tool Kit license

manually
ATTENTION
Ensure that Honeywell RC500 I/O Tool Kit is installed before you register the
Honeywell RC500 I/O Tool Kit license.

To register the Honeywell RC500 I/O Tool Kit license manually, perform the following
steps.

Step Action
1 Choose Start > All Programs > Honeywell Tools > Honeywell RC500 I/O
Tool Kit.

The following message appears.

2 Click Yes to register.

The Registration Status dialog box appears.

3 Click Request Registration Number.

The Contact Information dialog box appears.

3 Enter the details for all the mandatory fields. These details are available in
the document that is shipped along with the RC500 R200.1 CD.

Note:

• indicates that it is a mandatory field and must be provided.

• Enter the details for the other optional fields as required.

4 Click Next.

The Registration Levels dialog box appears.

R200 Honeywell RC500 Software Installation User's Guide 25

November 2011 Honeywell
3. Post-installation Tasks
3.2. Registering Honeywell RC500 I/O Tool Kit license manually

Step Action
5 Select the following features.
• Basic setup and maintenance of hardware modules

• Scalable Control System tools (tag sharing, ISaGRAF, IOmap)

• Datalogging use (confirmation and file retrieval)

Note: Do not type the Prepaid serial number.

6 Click Next.

The Request Registration Numbers dialog box appears.

7 Click Finish.

The registration status is updated as in the following Registration Status

dialog box.

26 Honeywell RC500 Software Installation User's Guide R200

Honeywell November 2011
 3. Post-installation Tasks
3.2. Registering Honeywell RC500 I/O Tool Kit license manually

Step Action
8 Click Enter Registration Number.

The Enter Registration Number dialog box appears.

9 Type the Registration number.

Note: If the registration is successful, the Registration status displays that

the registration is successful.
10 Close the Enter Registration Number dialog box and then click Register
Add-ons in the Registration Status dialog box.

The Add-on Registration dialog box appears.

11
In the Registration Number column, click for AGA Gas Flow
Calculations and DNP3.

A dialog box appears informing you to type the Registration number and
Number of stations authorized.
12 Enter information in the Registration number and Number of stations
authorized boxes and click OK.

ATTENTION
To edit the registration number, double-click it for the respective
Product Name.
13 In the Add-on Registration dialog box, click OK.
14 Close the Registration Status dialog box.

The Honeywell RC500 I/O Tool Kit registration is completed.

R200 Honeywell RC500 Software Installation User's Guide 27

November 2011 Honeywell
3. Post-installation Tasks
3.3. Registering ISaGRAF Open license

3.3 Registering ISaGRAF Open license

ATTENTION
• Ensure that ISaGRAF Open is installed on the same system where the
Honeywell RC500 I/O Tool Kit is installed.
• Ensure that USB Dongle (to be purchased by placing a purchase order)
is available.
• Ensure to register Honeywell RC500 I/O Tool Kit before registering
ISaGRAF.

To register the ISaGRAF license, perform the following steps.

Step Action
1 Connect the USB Dongle to the system where ISaGRAF is installed.
2 Choose Start > All Programs > Honeywell Tools > Honeywell RC500 I/O
Tool Kit.

The Honeywell RC500 I/O Tool Kit application opens.

3 Click Help > Registration.

The Registration Status dialog box appears.

4 Click Register ISaGRAF Open.

The Register ISaGRAF Open dialog box appears.

5 Type the ISaGRAF part number (RC-OW-1131-xx) that is available on the
USB Dongle you want to register.

Note: xx indicates the number of tags that can be exported.

For example, if you type the part number RC-OW-1131-32 that is available
with the USB Dongle, 32 indicates the number of tags that can be exported.

28 Honeywell RC500 Software Installation User's Guide R200

Honeywell November 2011
 3. Post-installation Tasks
3.3. Registering ISaGRAF Open license

Step Action

ATTENTION
Following are the part numbers for ISaGRAF that are available with
the respective registration numbers.

Part numbers Registration

numbers
RC-OW-1131-32 02P3-8E0A-0C6

RC-OW-1131-256 02P2-D9EC-317

RC-OW-1131-1000 02P3-8E0A-0C6

RC-OW-1131-BIG 02P4-C4BE-AB7
6 Enter version number and registration number for ISaGRAF. These details
are available in the document that is shipped along with the RC500 R200.1
CD.
7 Click OK.

The ISaGRAF is registered successfully.

R200 Honeywell RC500 Software Installation User's Guide 29

November 2011 Honeywell
3. Post-installation Tasks
3.3. Registering ISaGRAF Open license

30 Honeywell RC500 Software Installation User's Guide R200

Honeywell November 2011
 4. Switch Utility Installation
4.1 Installing the Switch Utility
To install the Switch Utility, perform the following steps.

Step Action
1 Insert the RC500 R200.1 CD into the CD-ROM drive.
2 Browse to the folder containing the Switch Utility and double-click the
SwitchUtility.exe.

The Welcome to the Switch Utility Setup Wizard page appears.

3 Click Next.

The License Agreement page appears.

4 Click I Agree to accept the license agreement.

The Choose Components page appears.

5 Select the required components you want to install and then click Next.

The Choose Install Location page appears, displaying the default

destination folder.

If you want to change the default destination folder, click Browse to specify a
different destination folder.

The Choose Start Menu Folder page appears.

6 Select the Start Menu folder in which you want to create the program
shortcut.
7 Click Next.

The Installing page appears.

R200 Honeywell RC500 Software Installation User's Guide 31

November 2011 Honeywell
4. Switch Utility Installation
4.1. Installing the Switch Utility

Step Action

ATTENTION
You must install Java runtime for Switch Utility to run, and load. If
Java runtime, was installed in your computer. A confirmation
message appears.
You can perform any one of the following:
• Click Yes to reinstall.
Or
• Click No to ignore.
8 Click Close after installing Java runtime.

The Completing the Switch Utility Setup Wizard page appears.

9 Click Finish.

32 Honeywell RC500 Software Installation User's Guide R200

Honeywell November 2011
 5. RC500 maintenance
5.1 Overview of RC500 maintenance
The Honeywell RC500 I/O Tool Kit installation supports the following:
• Modify: Using this option, you can add new components or remove the currently
installed components.
• Repair: Using this option, you can reinstall the selected components installed by the
previous setup.
• Remove: Using this option, you can remove all the selected components.

5.2 Taking backup of Honeywell RC500 I/O Tool Kit

project
Ensure to take backup of all RTU configuration details and save in any other location
other than the default location C:\Program Files\Honeywell Tools.
To save the configuration details of RTU, perform the following:

Step Action
1 Start the Honeywell RC500 I/O Tool Kit application.
2 On the menu bar, click File > Save Project As.

The SaveAs dialog box appears.

3 Browse to any location from Save In drop-down list and save the .6PJ file.

R200 Honeywell RC500 Software Installation User's Guide 33

November 2011 Honeywell
5. RC500 maintenance
5.3. Modifying Honeywell RC500 I/O Tool Kit components

5.3 Modifying Honeywell RC500 I/O Tool Kit components

Using the Modify option, you can remove the currently installed component or install a
new component along with the currently installed component.

Step Action
1 a) Choose Start > Control Panel > Add or Remove Programs.

The Add or Remove Programs dialog box appears.

b) Select Honeywell RC500 I/O Tool Kit and click Change/Remove.

The Welcome page appears.

or
a) Insert the RC500 R200.1 CD into the CD-ROM drive.
b) Browse to the folder containing the Honeywell RC500 I/O Tool Kit and
double-click the HoneywellIOTools.exe.
c) Click Run.

The Welcome page appears.

2 Click the Modify option button and then click Next.

The Select Components page appears.

3 Perform any one of the following to modify the installation, as required.
• If you want to remove a component, clear the check box corresponding to
the already installed component.

or
• If you want to add a component, select the component.

4 Click Next.

The Honeywell RC500 I/O Tool Kit is modified with the required components.

34 Honeywell RC500 Software Installation User's Guide R200

Honeywell November 2011
 5. RC500 maintenance
5.4. Repairing Honeywell RC500 I/O Tool Kit components

5.4 Repairing Honeywell RC500 I/O Tool Kit components

Using the Repair option, you can reinstall all the components installed during the
previous setup.
To repair Honeywell RC500 I/O Tool Kit components, perform the following steps.
Step Action
1 Insert the RC500 R200.1 CD into the CD-ROM drive.

ATTENTION
Repair option is currently not supported through Add/remove
programs.

The following error message appears, if you try to repair through

Add/remove programs.

2 Browse to the folder containing the Honeywell RC500 I/O Tool Kit and
double-click HoneywellIOTools.exe.

The File Download - Security Warning dialog box appears.

3 Click Run.

The Welcome page appears.

4 Click the Repair option button and then click Next.

All the components are reinstalled.

R200 Honeywell RC500 Software Installation User's Guide 35

November 2011 Honeywell
5. RC500 maintenance
5.5. Removing Honeywell RC500 I/O Tool Kit

5.5 Removing Honeywell RC500 I/O Tool Kit

Using the Remove option, you can remove all the Honeywell RC500 I/O Tool Kit
components, which are installed in the system.
To remove Honeywell RC500 I/O Tool Kit components, perform the following steps.
Step Action
1 a) Choose Start > Control Panel > Add or Remove Programs.

The Add or Remove Programs dialog box appears.

b) Select Honeywell RC500 I/O Tool Kit and click Change/Remove.

The Welcome page appears.

or
a) Insert the RC500 R200.1 CD into the CD-ROM drive.
b) Browse to the folder containing the Honeywell RC500 I/O Tool Kit and
double-click the HoneywellIOTools.exe.
c) Click Run.

The Welcome page appears.

2 Click the Remove option button and then click Next.

A confirmation message appears informing you to remove the selected

application and all its components.
3 Click OK.

The following message appears.

4 Select Don’t display this message again and then click Yes.

The Honeywell RC500 I/O Tool Kit components are removed.

36 Honeywell RC500 Software Installation User's Guide R200

Honeywell November 2011
 5. RC500 maintenance
5.6. Taking backup of ISaGRAF project

5.6 Taking backup of ISaGRAF project

Ensure to take backup of ISaGRAF project and save in any other location other than the
default location C:\Program Files\ISaGRAF Open\Projects\ISaGRAF\Prj.
To save the ISaGRAF project, perform the following:

Step Action
1 Browse for the folder that contains the ISaGRAF project at the following
location C:\Program Files\ISaGRAF Open\Projects\ISaGRAF \Prj.
2 Select the project folder that you want to take backup and zip it.
3 Browse to any location and save the zip file.

R200 Honeywell RC500 Software Installation User's Guide 37

November 2011 Honeywell
5. RC500 maintenance
5.7. Removing ISaGRAF

5.7 Removing ISaGRAF

Using the Remove option, you can remove all the ISaGRAF components, which are
installed in the system.
To remove ISaGRAF Open components, perform the following steps.
Step Action
1 a) Choose Start > Control Panel > Add or Remove Programs.

The Add or Remove Programs dialog box appears.

b) Select ISaGRAF Open and click Remove.

A confirmation message appears informing you to remove the selected

application and all its components.

or
a) Insert the RC500 R200.1 CD into the CD-ROM drive.
b) Browse to the folder containing the ISaGRAF Open and double-click the
isaopen.exe.
c) Click Run.

A confirmation message appears informing you to remove the selected

application and all its components.
2 Click Yes.

The InstallShield Wizard Complete page appears.

3 Click Yes, I want to restart my computer now, if you want to restart the
computer.

or

Click No, I will restart my computer later.

ATTENTION
It is recommended to restart the computer after you remove
ISaGRAF.
4 Click Finish.

The ISaGRAF Open setup is successfully removed.

38 Honeywell RC500 Software Installation User's Guide R200

Honeywell November 2011
 5. RC500 maintenance
5.8. Removing ISaGRAF Open license manager

5.8 Removing ISaGRAF Open license manager

To remove ISaGRAF Open license manager components, perform the following steps.

Step Action
1 Choose Start > Control Panel > Add or Remove Programs.

The Add or Remove Programs dialog box appears.

2 Select ISaGRAF Open and click Remove.

A confirmation message appears informing you to remove the selected

application and all its components.
3 Click Yes.

The ISaGRAF Open license manager is successfully removed.

R200 Honeywell RC500 Software Installation User's Guide 39

November 2011 Honeywell
Honeywell Process Solutions
1860 W. Rose Garden Lane
Phoenix, AZ 85027 USA