Holtek e-Link for 8-bit MCU OCDS

User’s Guide

Revision: V1.10 Date: ����������������

October 31, 2016
Holtek e-Link for 8-bit MCU OCDS
User’s Guide

Contents
HT8OCDS-ICE Introduction.................................................................................................... 3
HT8OCDS-ICE Composition.................................................................................................. 3
e-Link(for HT8OCDS)........................................................................................................................ 3
Target Board (with EV)....................................................................................................................... 4
HT8OCDS-ICE Usage Flow Description................................................................................ 4

Contents
IDE3000 Software Update................................................................................................................. 4
Hardware Connection........................................................................................................................ 4
Connect to the USB Port to Programming Using the IDE3000.......................................................... 6
HT8OCDS-ICE Usage Considerations................................................................................... 7
About the HT-IDE3000 Version.......................................................................................................... 7
About the e-Link (for HT8OCDS) Version.......................................................................................... 8
System Frequency............................................................................................................................. 8
Voltage and Current........................................................................................................................... 9
Emulation Function Comparison of HT8OCDS-ICE and e-ICE....................................................... 10
Multiple Breakpoint Modes...............................................................................................................11
RAM Real-time Monitor Function..................................................................................................... 12
OCDS or I/O Selection Option Function.......................................................................................... 13
HT8OCDS-ICE Usage Restriction........................................................................................ 14
HT8OCDS-ICE Switch and Indicators.................................................................................. 15
Switch.............................................................................................................................................. 15
Indicator........................................................................................................................................... 15
e-Link Size............................................................................................................................ 16

Rev. 1.10 2 of 17 October 31, 2016

Holtek e-Link for 8-bit MCU OCDS
User’s Guide

HT8OCDS-ICE Introduction
The HT8OCDS-ICE is Holtek’s third generation simulator, especially for use with Flash MCU
devices.

Compared with the e-ICE, the differences are as follows:

▀ The EV uses the OCDS (On-Chip Debug Support) structure that requires only two signal lines to
debug.

Holtek e-Link for OCDS User’s Guide

▀ The EV pin number is the same or has 1 to 2 more pins than the IC pins which can be soldered to
the application board making tests more convenient.

▀ Provides multiple breakpoint functions

▀ Provides a RAM real monitor function
▀ Wider operating voltage range of 1.7V~5.5V

HT8OCDS-ICE Composition
The HT8OCDS-ICE is composed of an e-Link (for HT8OCDS) + Target Board (with EV)

e-Link(for HT8OCDS)
▀ e-Link is the common name for the Holtek ICE series and has the same appearance. Holtek will
provide an e-LinkBox.cmd for the updates for different applications. Here it should be updated
as Holtek 8-Bits MCU OCDS.

▀ e-Link Appearance:

Rev. 1.10 3 of 17 October 31, 2016

Holtek e-Link for 8-bit MCU OCDS
User’s Guide

Target Board (with EV)

The EV is an IC with an OCDS interface

▀ During the debug process, the e-Link will implement a series of operations such as single step,
full speed, stop, breakpoint setting etc. by transmitting instructions to the EV.

▀ During the non-debug process, the EV is the same as an IC and works in the same way.

HT8OCDS-ICE Usage Flow Description

Holtek e-Link for OCDS User’s Guide

IDE3000 Software Update
The third generation emulator software still uses the IDE3000 but is only supported by versions
starting from V7.6.

Log on to Holtek official website to download the latest IDE3000.

Hardware Connection
▀ e-Link(for HT8OCDS) Pin Assignment

Rev. 1.10 4 of 17 October 31, 2016

Holtek e-Link for 8-bit MCU OCDS
User’s Guide

HT8OCDS-ICE Pin Definition

Name Description Direction Paremeter

e-Link voltage output pin when the power is supplied to the
e-Link→ 1.7V~5.5V
Target Board.
VDD
e-Link voltage input pin when the external power is
e-Link← 1.7V~5.5V
supplied to the Target Board.
OCDSCK The OCDS CLK signal during programming e-Link→ 1.7V~5.5V

Holtek e-Link for OCDS User’s Guide

OCDSDA The OCDS Data signal during programming e-Link ↔ 1.7V~5.5V
GND e-Link Ground e-Link ↔ 0V
Reserved Reserved e-Link signal pin Unknown Unknown
Note: The VDD, OCDSCK, OCDSDA and GND are the necessary pins of the HT8OCDS-ICE. Even if the
external power is supplied to the Target Board, the same VDD is still necessary so as to be used
as the reference voltage of the output potential for the e-Link. Simultaneously the Options in the
IDE3000 must be set to VDD External.
Pins marked as Reserved in the e-Link are not NC pins for which the user should note that the
voltage is unknown.

▀ HT8OCDS-ICE Hardware Connection

Rev. 1.10 5 of 17 October 31, 2016

Holtek e-Link for 8-bit MCU OCDS
User’s Guide

Connect to the USB Port to Programming Using the IDE3000

▀ If the connection is successful, the following message will pop up:

Holtek e-Link for OCDS User’s Guide

Online Prompt

▀ If the connection failed or no connection, the following message will pop up:

Offline Prompt

Rev. 1.10 6 of 17 October 31, 2016

Holtek e-Link for 8-bit MCU OCDS
User’s Guide

HT8OCDS-ICE Usage Considerations

About the HT-IDE3000 Version
Before using the HT8OCDS-ICE, ensure that the IDE3000 is the latest version.

▀ Check the “Help\About HT-IDE3000…” in the function menu for the version information.
▀ If it is version is 7.6 or newer, when the IDE3000 is enabled, the IDE will automatically detect
if it is the latest version by prompting whether an update is required, or click “Help\Check Live

Holtek e-Link for OCDS User’s Guide

Update…” for a manual update.

Windows Screen

Rev. 1.10 7 of 17 October 31, 2016

Holtek e-Link for 8-bit MCU OCDS
User’s Guide

Help Window

Holtek e-Link for OCDS User’s Guide

About the e-Link (for HT8OCDS) Version
▀ If the e-Link(for HT8OCDS) f/w is an old version, the following message will pop up when
connecting to the IDE3000

▀ If the EV is an old version, the following message will pop up when connecting to the IDE3000.

System Frequency
▀ The e-Link (for HT8OCDS) is not able to provide the system frequency for the EV. When using
the HT8OCDS-ICE, it is necessary to connect the required HXT, ERC or LXT according to
actual application requirements.

▀ Generally the HIRC calibration for the EV has been to the value at 5V when manufactured.
Operation under other voltage points may cause some HIRC deviation.

Rev. 1.10 8 of 17 October 31, 2016

Holtek e-Link for 8-bit MCU OCDS
User’s Guide

Voltage and Current

▀ The operating voltage of the HT8OCDS-ICE ranges from 1.7V~5.5V.
● e-Link supplies power to the Target Board and setup the voltage parameters:

e-Link supplies power to the Target Board

Holtek e-Link for OCDS User’s Guide

● External power supplies to the Target Board, check the External square:

External power supplies to the Target Board

▀ When e-Link supplies power to Target Board, if there is still an external power supply to Target
Board, in the IDE3000 Build process, the prompt window which requires the removal of the
external power supply will pop up to avoid power conflict.

power supply prompt window

▀ When the e-Link supplies power to the Target Board, if the current load is large, some VDD
output errors may occur.
eg: When the load current is 100mA~200mA, the actual VDD output will have a rather low
value of 0.1V~0.2V.
It is recommended to configure the VDD together with the consideration of this error range.

Rev. 1.10 9 of 17 October 31, 2016

Holtek e-Link for 8-bit MCU OCDS
User’s Guide

Emulation Function Comparison of HT8OCDS-ICE and e-ICE

Differences between the HT8OCDS-ICE and e-ICE.

Description Paremeter

FW Update The emulator can update the FW through the IDE3000. Need to change MEV

The EV is of 128QFP or
Pins can be soldered on to the application board for
208QFP Requires DuPont line
Pin Assignment direct adjustment.
or other connectors to connect

Holtek e-Link for OCDS User’s Guide

Good signal connection, quick and convenient
with the application board.
Total of 7 Breakpoint modules; Breakpoint number unlimited;
Breakpoint setting during free run; No Bbreakpoint setting during
Break Point
Breakpoint setup available in ROM, RAM, EEDATA; free run;
Diverse Breakpoint format Breakpoint setting only in ROM;
RAM Monitor Supported Not supported
Cannot be placed at the last
HALT Available at any location
address of ROM Bank0
OCDSDA/ OCDSCK Pin Share function unavailable during rogramming No restriction
Trace Not supported Instruction tracing
SysFreq e-Link not provided
Reset circuit required when executing the Reset
Reset Pin
function

Rev. 1.10 10 of 17 October 31, 2016

Holtek e-Link for 8-bit MCU OCDS
User’s Guide

Multiple Breakpoint Modes

▀ In the IDE3000 tool menu, select “Debug\Breakpoints” or use shortcut “Ctrl+B”
▀ Although only seven breakpoint modules are available, each breakpoint module can setup the
object control and control range:
Code type: When the PC access an address or a range is setup, it will break automatically.
Data\EEData type: when an address or a range of RAM/EEData is read / written, it will break
automatically.

Holtek e-Link for OCDS User’s Guide

▀ An Auto Break can be setup when any of the following conditions is satisfied, just tick in the
Event condition box.
PC \ Stack \ Cycle Count Overflow \ Stack Underflow \ LVR \ Wakeup

Breakpoint Setting Window

Rev. 1.10 11 of 17 October 31, 2016

Holtek e-Link for 8-bit MCU OCDS
User’s Guide

RAM Real-time Monitor Function

▀ In the IDE3000 tool menu, select “Debug\RAM Monitor”
▀ Set the RAM monitor range, and tick it
▀ Monitor up to 256 RAM unit at the maximum , each group monitor addresses can not be repeated
▀ Click “start” to begin to monitor the RAM status
▀ Move “Update Speed” to control the refresh rate

Holtek e-Link for OCDS User’s Guide

RAM Monitor Window

Rev. 1.10 12 of 17 October 31, 2016

Holtek e-Link for 8-bit MCU OCDS
User’s Guide

OCDS or I/O Selection Option Function

▀ When OCDSDA/OCDSCK is pin-shared with I/O, most of the EV can divide the shared pins
into the OCDSEV mode and the Real IC mode through the OCDS or I/O Selection option;
OCDSEV mode: whether e-Link is online or offline, the pin-shared function of OCDSDA/
OCDSCK is invalid;
Real IC mode: when e-Link is offline, the pin-shared function of OCDSDA/OCDSCK is the
same as the IC pins function; when e-Link is online, the function is still invalid;
Note: When the EV is setup to be in the Real IC mode, then if the target board power is

Holtek e-Link for OCDS User’s Guide

externally supplied, no emulation can be carried out. However if emulation is required,
then the external power must be first removed and it must be switched to the OCDS mode.

▀ OCDS or I/O Selection option usage

After e-Link connects successfully, click “Tools\Switch OCDS Mode” in the IDE3000 menu, the
OCDS Mode selection screen will pop up.

OCDS Mode selection

In the OCDS Mode selection screen, the current EV mode is default. Users select the OCDS
mode or the Real IC mode according to their needs, click OK to complete switch.
Note: when switching mode, the power supply to the Target Board must be removed.

▀ If the EV has no OCDS or I/O Selection option, when e-Link connects successfully, the IDE3000
menu “Tools\Switch OCDS Mode” in gray is unavailable.
When e-Link is online, the pin-shared function of OCDSDA/OCDSCK is invalid.
When e-Link is offline, the pin-shared function of OCDSDA/OCDSCK is the same as the IC
pins function.

Rev. 1.10 13 of 17 October 31, 2016

Holtek e-Link for 8-bit MCU OCDS
User’s Guide

HT8OCDS-ICE Usage Restriction

▀ EV and IC Pin Assignment
OCDSDA\OCDSCK may be pin-shared with an I/O or alone, so the pin number of the EV
maybe the same or 1~2 pins more than that of the IC.

▀ OCDSDA/OCDSCK can not connect to capacitor, when OCDSCK is pin-shared with the reset
pin, please refer to the following reset circuit.

Holtek e-Link for OCDS User’s Guide

Recommended Reset Circuit

OCDSCK should
be connected here

▀ When e-Link supplies power to the Target Board, the maximum current consumption is 200mA.
If the power consumption of the Target Board exceeds 200mA, the external power supply to the
Target Board should be selected.

▀ When e-Link supplies power to the Target Board, the maximum capacitance which the VDD pin
links to is 100uF.

Rev. 1.10 14 of 17 October 31, 2016

Holtek e-Link for 8-bit MCU OCDS
User’s Guide

HT8OCDS-ICE Switch and Indicators

Switch
The switch is used to reset the HT8OCDS-ICE.

Indicator
▀ Status
Yellow shows if the e-Link is providing power “to the Target Board”.

Holtek e-Link for OCDS User’s Guide

Continuously on: Power to the Target Board
Continuously off: No power to the Target Board

▀ Error
Red means that the e-Link operation has an “error”
Continuously on: Abnormal operation
Continuously off: Normal operation

▀ Active
Blue means the “duty load” of the e-Link
Slow Flashing: Idle, standing by ready at an interval of 1s (IDE3000 not operational)
Flasghin: Busy, the flash frequency and duration depends upon the number of duties.

Rev. 1.10 15 of 17 October 31, 2016

Holtek e-Link for 8-bit MCU OCDS
User’s Guide

e-Link Size
▀ Back and side e-Link dimensions (unit: mm)

Holtek e-Link for OCDS User’s Guide

▀ e-Link back slot dimensions (unit: mil)

Rev. 1.10 16 of 17 October 31, 2016

Holtek e-Link for 8-bit MCU OCDS
User’s Guide

Holtek e-Link for OCDS User’s Guide

Copyright© 2016 by HOLTEK SEMICONDUCTOR INC.
The information appearing in this Data Sheet is believed to be accurate at the time
of publication. However, Holtek assumes no responsibility arising from the use of
the specifications described. The applications mentioned herein are used solely for
the purpose of illustration and Holtek makes no warranty or representation that such
applications will be suitable without further modification, nor recommends the use of
its products for application that may present a risk to human life due to malfunction
or otherwise. Holtek's products are not authorized for use as critical components in
life support devices or systems. Holtek reserves the right to alter its products without
prior notification. For the most up-to-date information, please visit our web site at
http://www.holtek.com.tw/en/home.

Rev. 1.10 17 of 17 October 31, 2016