Scribd
Upload
112 views

Propagate A Default Route in OSPFv2

The document outlines steps to configure a default route on router R2 to the internet, propagate that route using OSPF to routers R1 and R3, and then verify connectivity from PCs 1-3 to a web server by confirming the default route is in the routing tables and ping tests to the web server IP are successful. It provides details on the network topology, device IP addresses, and configuration commands used to complete the objectives of propagating a default route and verifying connectivity.

Uploaded by

Muharam Rizqi Ananda
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
112 views

Propagate A Default Route in OSPFv2

The document outlines steps to configure a default route on router R2 to the internet, propagate that route using OSPF to routers R1 and R3, and then verify connectivity from PCs 1-3 to a web server by confirming the default route is in the routing tables and ping tests to the web server IP are successful. It provides details on the network topology, device IP addresses, and configuration commands used to complete the objectives of propagating a default route and verifying connectivity.

Uploaded by

Muharam Rizqi Ananda
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Name : Muharam Rizqi Ananda

ID : 01123656201-60
Class : A

Packet Tracer - Propagate a Default Route in OSPFv2


Addressing Table
Device Interface IPv4 Address Subnet Mask Default Gateway

R1 G0/0 172.16.1.1 255.255.255.0 N/A


R1 N/A

S0/0/0 172.16.3.1 255.255.255.252


R1 N/A

S0/0/1 192.168.10.5 255.255.255.252

R2 G0/0 172.16.2.1 255.255.255.0 N/A


R2 N/A

S0/0/0 172.16.3.2 255.255.255.252


R2

N/A

S0/0/1 192.168.10.9 255.255.255.252


R2 N/A

S0/1/0 209.165.200.225 255.255.255.224

R3 G0/0 192.168.1.1 255.255.255.0 N/A


R3 N/A

S0/0/0 192.168.10.6 255.255.255.252


R3 N/A

S0/0/1 192.168.10.10 255.255.255.252

PC1 NIC 172.16.1.2 255.255.255.0 172.16.1.1

PC2 NIC 172.16.2.2 255.255.255.0 172.16.2.1

PC3 NIC 192.168.1.2 255.255.255.0 192.168.1.1

Web Server NIC 64.100.1.2 255.255.255.0 64.100.1.1

Objectives
Part 1: Propagate a Default
Route Part 2: Verify
Connectivity

Background
In this activity, you will configure an IPv4 default route to the Internet and propagate that default
route to other OSPF routers. You will then verify the default route is in downstream routing tables
and that hosts can now access a web server on the Internet.

Instructions Part 1: Propagate a Default Route


Step 1: Test connectivity to the Web Server
a. From PC1, PC2, and PC3, attempt to ping the Web Server IP address, 64.100.1.2.
Questions:

Were any of the pings successful? No.


What message did you receive, and which device issued the message? Destination
unreachable from R2.
Type your answers here.
b. Examine the routing tables on routers R1, R2, and R3.
Open configuration window
Question:

What statement is present in the routing tables that indicates that the pings to the Web Server
will fail? Gateway of last resort is not set
Type your answers here.

Step 2: Configure a default route on R2.


Configure R2 with a directly attached default route to the Internet.
R2(config)# ip route 0.0.0.0 0.0.0.0 Serial0/1/0
Note: Router will give a warning that if this interface is not a point-to-point connection, it may
impact performance. You can ignore this warning because it is a point-to-point connection.

Step 3: Propagate the route in OSPF.


Configure OSPF to propagate the default route in OSPF routing updates.
R2(config)# router ospf 1
R2(config-router)# default-information originate

Step 4: Examine the routing tables on R1 and R3.


Examine the routing tables of R1 and R3 to verify that the route has been propagated.
R1> show ip route
<output omitted>
Gateway of last resort is 172.16.3.2 to network 0.0.0.0
<output omitted>
O*E2 0.0.0.0/0 [110/1] via 172.16.3.2, 00:00:08, Serial0/0/0
!-------------------
R3> show ip route
<output omitted>
Gateway of last resort is 192.168.10.9 to network 0.0.0.0
<output omitted>
O*E2 0.0.0.0/0 [110/1] via 192.168.10.9, 00:08:15, Serial0/0/1
Close configuration window

Part 2: Verify Connectivity


Verify that PC1, PC2, and PC3 can ping the web server.

You might also like