Scribd
Upload
50 views5 pages

HITACHI

This document provides information about connecting a HITACHI H series PLC to a MT500 HMI including: - A list of compatible HITACHI PLC models from the H series - Recommended settings for the HMI such as PLC type, communication port, baud rate, and parity - Device address formats and ranges for reading and writing PLC data - Wiring diagrams for connecting the MT500 to different HITACHI PLC ports including RS232, RS485 4-wire, and RS485 2-wire configurations

Uploaded by

Eta Courses
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
50 views5 pages

HITACHI

This document provides information about connecting a HITACHI H series PLC to a MT500 HMI including: - A list of compatible HITACHI PLC models from the H series - Recommended settings for the HMI such as PLC type, communication port, baud rate, and parity - Device address formats and ranges for reading and writing PLC data - Wiring diagrams for connecting the MT500 to different HITACHI PLC ports including RS232, RS485 4-wire, and RS485 2-wire configurations

Uploaded by

Eta Courses
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

HITACHI H series (CPU port)

Compatible PLCs
Family Model
HITACHI EH-150, Micro-EH, H20, H40, H64, H200, H250, H252, H300, H302, H700, H702,
H series H1000, H1002, H2000, H4010
HITACHI Web site: http://www.vanet.hitachi.co.jp/public/Div/iced/english/products/

HMI Setting:
Parameters Recommend Option Notes
PLC type HITACHI
Com port RS232 RS232, RS485 Must match the PLC’s port setting.
Baud rate 19200 9600, 19200, 38400 Must match the PLC’s port setting.
Parity bit Even Even Must match the PLC’s port setting.
Data Bits 7 7 Must match the PLC’s port setting.
Stop Bits 1 1 Must match the PLC’s port setting.
HMI Station No. 0 0-255 Does not apply to this protocol.
PLC Station No. 0 0-255 Does not apply to this protocol.

Online Simulator OK
Direct Online Simulator OK
Extend address mode Does not Support

PLC Setting:
Communication mode 19200,E,7,1(default)
Select

Device address :
Device
Bit/Word Format Range Memo
Type
B X hhh(h) hhh: 0~FFFF (h):0~F External Input-bit(X)
B Y hhh(h) hhh: 0~FFFF (h):0~F External Output-bit(Y)
B M hhh(h) hhh: 0~FFFF (h):0~F Data area-bit(M)
B T hhh(h) hhh: 0~FFFF (h):0~F Timer(T)
B R hhh(h) hhh: 0~FFFF (h):0~F Internal Output(R)
B L hhh(h) hhh: 0~FFFF (h):0~F Link area-bit(L)
W TC hhh hhh: 0~FF Timer/Counter current value
W WX hhh hhh: 0~270F External Input-word(X)
W WY hhh hhh: 0~270F External Output-word(Y)
W WR hhh hhh: 0~270F Internal Output-word(R)
W WL hhh hhh: 0~270F Link area-word(L)
W WM hhh hhh: 0~270F Data area-word(M)
Wiring diagram :
WARNING: If your communications cable is not wired exactly as shown in our cable assembly
instructions, damage to the MT500 or loss of communications can result.

CPU TYPE Port 1 Port 2


EH-150/CPU 104A RS-232 RS-232
EH-150/CPU 208A RS-232 RS-232
EH-150/CPU 308A RS-232/RS-485 RS-232
Port 1
EH-150/CPU 316A RS-232/RS-485 RS-232
Port 2 EH-150/CPU 448A RS-232/RS-485 RS-232

Switch Number
1 OFF Normal mode
2 OFF TRNS0 operation
3, 4 3 4 Port1 transmission speed
ON ON 4,800 bps Doesn’t support
OFF ON 9,600 bps
ON OFF 19,200 bps Default
OFF OFF 38,400 bps
5 ON Dedicated port
6 6 PHL Port2 transmission speed
Toggle-Switch
ON Low 9,600 bps
PHL
ON High 38,400 bps
Low
OFF Low 4,800 bps Doesn’t support
OFF High 19,200 bps Default
PHL
7 OFF (System mode) Do not turn on. High
8 OFF (System mode) Do not turn on.

EH-150 port1 RS232


MT500 PLC[232] HITACHI EH-150 port1
9P D-SUB Male 8pin RJ45 Male
2 TX 6 RD
3 RX 5 SD
5 GND 1 SG
7 CTS 8 RS Port 1
8 RTS 7 DR 8pin RJ45 Female
EH-150 port1 RS485 4wire (RS422)
MT500 PLC[485] HITACHI EH-150 port1
9P D-SUB Female 8pin RJ45 Male
1 RX- 5 TX-
2 RX+ 4 TX+
3 TX- 6 RX-
4 TX+ 7 RX+ Port 1
5 GND 1 SG 8pin RJ45 Female

MT500 PLC[232]
9P D-SUB Male
7 CTS
8 RTS
EH-150 RS-485 connect must short the PLC[232] port pin 7,8.

EH-150 port1 RS485 2wire


MT500 PLC[485] HITACHI EH-150 port1
9P D-SUB Female 8pin RJ45 Male
1 RX- 5 TX-
2 RX+ 4 TX+
3 TX- 6 RX-
4 TX+ 7 RX+ Port 1
5 GND 1 SG 8pin RJ45 Female

MT500 PLC[232]
9P D-SUB Male
7 CTS
8 RTS
EH-150 RS-485 connect must short the PLC[232] port pin 7,8.

EH-150 port2 RS232


MT500 PLC[232] HITACHI EH-150 port2
9P D-SUB Male 8pin RJ45 Male
2 TX 6 RD
3 RX 5 SD
5 GND 1 SG
7 CTS 8 RS Port 2
8 RTS 7 DR 8pin RJ45 Female
H series CPU RS232 port
MT500 PLC[232] HITACHI H series CPU RS232
9P D-SUB Male 15p D-SUB Male
2 TX 3 RXD
3 RX 2 TXD
5 GND 9 SG
7 CTS 4 RTS
10 SG
5 CTS
7 DSR
8 PHL
14 PV12

You might also like