Scribd
Upload
77 views2 pages

Indrivetec PPS

The document discusses Indrivetec AG's FlexConvert-BESS-PPS energy storage system. It provides technical specifications for four models with output power ratings ranging from 580 kVA to 2320 kVA. The system can correct all nine IEEE-defined power problems including power failures, surges, sags, under/over voltages, frequency variations, switching transients, and harmonic distortions. It has advantages such as voltage independence, scalability, voltage control, parallel operation for redundancy, and integrated UPS with sag compensation.

Uploaded by

hermanto
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
77 views2 pages

Indrivetec PPS

The document discusses Indrivetec AG's FlexConvert-BESS-PPS energy storage system. It provides technical specifications for four models with output power ratings ranging from 580 kVA to 2320 kVA. The system can correct all nine IEEE-defined power problems including power failures, surges, sags, under/over voltages, frequency variations, switching transients, and harmonic distortions. It has advantages such as voltage independence, scalability, voltage control, parallel operation for redundancy, and integrated UPS with sag compensation.

Uploaded by

hermanto
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

INDRIVETEC AG

"bricks up" flexible energy storage systems


INNOVATION “BRICK” FlexConvert-BESS-PPS

Technical data
Output FC-PCS-580 FC-PCS-1160 FC-PCS-1740 FC-PCS-2320
Rated Power 580 kVA 1160 kVA 1740 kVA 2320 kVA

Indrivetec AG - Hagenholzstrasse 71 - CH-8050 Zürich – Phone + 41 44 515 37 00 - [email protected] – www.indrivetec.com


Rated apparent power 464 kW 928 kW 1392 kW 1856 kW
Maximum current 700 A 1400 A 2100 A 2800 A
Rated voltage 480 V
Frequency 50 Hz / 60 Hz
Power factor 0.8
FlexConvert FC500 FC1000 FC1500 FC2000
Input
Rated voltage 480 V
Frequency 50 Hz / 60 Hz
Current distortion <3%
Power factor 0.99
General data
Dimensions (D x W x H) 3200x800x2000 mm 4400x800x2000 mm 6000x800x2000 mm 6800x800x2000 mm
Weight 6 tons 8 tons 10 tons 12 tons
Technical data are subject to change, even for reasons on country-specific deviations.
Indrivetec assumes no liability for errors and omissions.

FlexConvert BESS-PPS corrects all nine IEEE defined power problems

Power Failure Power Surge Power Sag

A total loss of utility Short-term high voltage Short-term low voltage


power (>110% of normal) (a dip in AC power)

Under Voltage Over Voltage Electrical Line Noise

Reduced line voltage Increased line voltage High power frequency


for an extended period for an extended period wave usually from ra-
(minutes to days) dio frequency interfer-
ence
Frequency Variation Switching Transient Harmonic Distortion

Loss of stability in the Instantaneous under- Distortion in the nor-


power’s normal fre- voltage in the range of mal power wave, gen-
quency (50-60Hz) nanoseconds erally transmitted by
unequal power loads

SWISS engineering
INDRIVETEC AG
INNOVATION “BRICK” FlexConvert-BESS-PPS

FlexConvert-BESS-PPS
Power Protection System (UPS) with integrated ESS

Indrivetec AG - Hagenholzstrasse 71 - CH-8050 Zürich – Phone + 41 44 515 37 00 - [email protected] – www.indrivetec.com


System advantages
Voltage independent, parallel on-line single conversion static UPS with flexible ESS integration
Modular and scalable design for grid voltage and power quality
Voltage control at all times
Parallel operation for Power and Redundancy
No transfer time from or to Bypass
Minimum number of parts in the main power flow
High efficiency on-line mode with voltage control
UPS integrated with SAG compensation features
Load power factor correction
Continuous load harmonic cancellation

Block diagram FlexConvert-BESS-PPS

SWISS engineering

You might also like