THE STRUT-AND-TIE MODEL

OF CONCRETE STRUCTURES

By
Dr. Samith Buddika

Faculty of Engineering
University of Peradeniya
 Introduction
The Strut-and-Tie is a unified approach that
considers all load effects (M, N, V, T)
simultaneously
The Strut-and-Tie model approach evolves as one
of the most useful design methods for shear critical
structures and for other disturbed regions in
concrete structures
The model provides a rational approach by
representing a complex structural member with an
appropriate simplified truss models
There is no single, unique STM for most design
situations encountered. There are, however, some
techniques and rules, which help the designer,
develop an appropriate model
History and Specifications
The subject was presented by Schlaich et al
(1987) and also contained in the texts by
Collins and Mitchell (1991) and MacGregor
(1992)
One form of the STM has been introduced in
the new AASHTO LRFD Specifications (1994),
which is its first appearance in a design
specification in the US
It will be included in ACI 318-02 Appendix A
Bernoulli Hypothesis
Bernoulli hypothesis states that: " Plane
section remain plane after bending…"
Bernoulli's hypothesis facilitates the flexural
design of reinforced concrete structures by
allowing a linear strain distribution for all
loading stages, including ultimate flexural
capacity
N.A.
St. Venant’s Principle
St. Venant's Principle states that: " The
localized effects caused by any load
acting on the body will dissipate or
smooth out within regions that are
sufficiently away from the location of the
load…"
 B- & D-
Regions
for
Various
Types of
Members
Design of B & D Regions
The design of B (Bernoulli or Beam) region is
well understood and the entire flexural
behavior can be predicted by simple
calculation
Even for the most recurrent cases of D
(Disturbed or Discontinuity) regions (such as
deep beams or corbels), engineers' ability to
predict capacity is either poor (empirical) or
requires substantial computation effort (finite
element analysis) to reach an accurate
estimation of capacity
 STM
for
Simple
Span
Beam
 Feasible Inclined Angle 
Swiss Code: 0.5  Cot   2.0 (=26° to 64°)
European Code: 3/5  Cot   5/3 (=31° to 59°)
Collin’s & Mitchells
min = 10 + 110(Vu/[fcbwjd]) deg
max = 90 - min deg
ACI 2002: min =25°; (25°  recom  65° here)
If small  is assumed in the truss model, the
compression strength of the inclined strut is
decreased.
 STM of a Deep Beam

ACI Section 10.7.1 For Deep Beam:

L/d < 5/2 for continuous span; < 5/4 for simple span
ACI Section 11.8: L/d <5 (Shear requirement)
 Deep
Beam
Stress
and I ts
STM
Model
 Transition
from Deep Beam to Beam
STM Model
for a
Tw o-span
Continuous
Beam
 Basic Concepts
Strut-and-Tie Model: A conceptual framework
where the stress distribution in a structure is
idealized as a system of

Strut Compression Concrete

Member
Tie or Tension Reinforcement
Stirrup Member
Node Connection Concrete
Examples of STM Models
 Strut Angle of STM Model
A STM developed with struts parallel to the
orientation of initial cracking will behave very well
A truss formulated in this manner also will make the
most efficient use of the concrete because the
ultimate mechanism does not require reorientation of
the struts
Low er Bound Theorem
of Plasticity
A stress field that satisfies equilibrium
and does not violate yield criteria at any
point provides a lower-bound estimate
of capacity of elastic-perfectly plastic
materials
For this to be true, crushing of concrete
(struts and nodes) does not occur prior
to yielding of reinforcement (ties or
stirrups)
Limitation of The Truss Analogy
The theoretical basis of the truss analogy is
the lower bound theorem of plasticity
However, concrete has a limited capacity to
sustain plastic deformation and is not an
elastic-perfectly plastic material
AASHTO LRFD Specifications adopted the
compression theory to limit the compressive
stress for struts with the consideration of the
condition of the compressed concrete at
ultimate
 Prerequisites
Equilibrium must be maintained
Tension in concrete is neglected
Forces in struts and ties are uni-axial
External forces apply at nodes
Prestressing is treated as a load
Detailing for adequate anchorage
 Problems
in STM Applications

1.How to construct a Strut-and-Tie

model?
2.If a truss can be formulated, is it
adequate or is there a better one?
3.If there are two or more trusses for the
same structure, which one is better?
 Struts
A. Compression struts fulfill two functions in
the STM:
1. They serve as the compression chord of
the truss mechanism which resists
moment
2. They serve as the diagonal struts which
transfer shear to the supports

B. Diagonal struts are generally oriented

parallel to the expected axis of cracking
 Types of Struts
There are three types of struts that will be
discussed:

1. The simplest type is the “prism” which has a

constant width
2. The second form is the “bottle” in which the
strut expands or contracts along its length
3. The final type is the “fan” where an array of
struts with varying inclination meet at or
radiate from a single node
Three Types of Struts
Compression Struts
 Ties
Tensions ties include stirrups, longitudinal
(tension chord) reinforcement, and any
special detail reinforcement
A critical consideration in the detailing of the
STM is the provision of adequate anchorage
for the reinforcement
If adequate development is not provided, a
brittle anchorage failure would be likely at a
load below the anticipated ultimate capacity
 Nodes
Nodes are the connections of the STM,
i.e., the locations at which struts and
ties converge
Another way of describing a node is the
location at which forces are redirected
within a STM
 Type of
Singular
Nodes
( Schlaich
et al
1987)
I dealized Forces
at Nodal Zones
Singular
and
Smeared
Nodes
STM Model Design Concept
The successful use of the STM requires an
understanding of basic member behavior and
informed engineering judgment
In reality, there is almost an art to the
appropriate use of this technique
The STM is definitely a design tool for
thinking engineers, not a cookbook analysis
procedure
The process of developing an STM for a
member is basically an iterative, graphical
procedure
 STM
Model
Design
Flow
Chart
 Methods for
Formulating STM Model

Elastic Analysis based on Stress

Trajectories
Load Path Approach
Standard Model
 Elastic
Analysis
for the
STM
Model A
 Elastic Analysis
for the STM Models B & C
 Elastic Analysis Approach
Procedures
1. Isolate D-regions
2. Complete the internal stresses on the
boundaries of the element
3. Subdivide the boundary and compute
the force resultants on each sub-length
4. Draw a truss to transmit the forces from
boundary to boundary of the D-region
5. Check the stresses in the individual
members in the truss
 STM
Model C
Example
using
Elastic
Analysis
STM Model C Example
Reinforcement
 Load
Path
Approach
( Schlaich
et al.
1987)
Example of
Determining
STM Model
Geometry
Factors Affecting Size of
Compression Strut

Location and distribution of

reinforcement (tie) and its anchorage
Size and location of bearing
 Nodal Zones
These dimensions are determined for each
element using
(1) the geometry of the member and the STM,
(2) the size of bearings,
(3) the size of loaded areas,
(4) the location and distribution of reinforcement, and
(5) the size of tendon anchorages, if any
Struts and ties should be dimensioned so that
the stresses within nodes are hydrostatic, i.e.,
the stress on each face of the node should be
the same
Hydrostatic Nodal Zones
 Cracking of Compression Strut

bef=a+/6

T=C(1-a/bef)/4
STM Models A & B for
Anchorage Zones
STM Models C & D for
Anchorage Zones
Examples
of Good
and Poor
STM
Models
• Good Model is more closely approaches to the elastic stress trajectories
• Poor model requires large deformation before the tie can yield; violate the
rule that concrete has a limited capacity to sustain plastic deformation
 Nonlinear finite element comparison of
three possible models of a short cantilever
(d) behaves almost elastically
until anticipated failure load

(c) requires the largest

amount of plastic
deformation; thus it is more
likely to collapse before
reaching the failure load level
STM Model for a Ledged End
Beam-Column Opening Joints
Efficiency of Opening Joints
T-Joints
Concentrated Load on a
Bearing Wall
 STM
Models
( a)
Tensile Flange
w / Opening
( b)
Compression
Flange
w / Opening
 STM Models
(c) ) Web supported by Diaphragm
(d) )Pier and Diaphragm w / Single
Support
 STM Models
(e) ) Other Model for
Diaphragm
(f) ) Pier and Diaphragm w / Tw o
Supports
 STM
Models
(g) Piers on
a Pile Cap
 Examples of STM Models &
Reinforcement ( Schlaich et al 1987)
Limiting
Stresses
for Truss
Elements
Limiting Compressive Stress in Strut
AASHTO LRFD 5.6.3.3.3
'
fc
f cu   0.85 f c'
0.8 1701
where:

e1 = (es + 0.002) cot2 a s

fcu = the limiting compressive stress

as = the smallest angle between the compressive

strut and adjoining tension ties (DEG)

es = the tensile strain in the concrete in the

direction of the tension tie (IN/IN)
Simplified Values for Limiting Compressive
Stress in Strut, f cu ( Schlaich et al. 1987)
For an undisturbed and uniaxial state of compressive stress:

fcu = 1.0 (0.85 fc?) = 0.85 fc?

If tensile strains in the cross direction or transverse tensile
reinforcement may cause cracking parallel to the strut with
normal crack width:
fcu = 0.8 (0.85 fc?) = 0.68 fc?
As above for skew cracking or skew reinforcement:
fcu = 0.6 (0.85 fc?) = 0.51 fc?
For skew cracks with extraordinary crack width – such cracks
must be expected if modeling of the struts departs
significantly from the theory of elasticity’s flow of internal
forces:
fcu = 0.4 (0.85 fc?) = 0.34 fc?
 Strength of Compressive Strut
AASHTO LRFD 5.6.3.3.3

Pr = F Pn (LRFD 5.6.3.2-1)

Pn = fcu Acs (LRFD 5.6.3.3.1-1)

where:

F = 0.70 for compression in strut-and-tie models

(LRFD 5.5.4.2.1)

Acs = effective cross-sectional area of strut

(LRFD 5.6.3.3.2)
 ACI 2002 STM Model
Design of struts, ties, and nodal zones shall be based on:
Fn  Fu
The nominal compressive strength of a strut without
longitudinal reinforcement:
Fns  f cu Ac
The effective compressive strength of the concrete
in a strut is:
f cu  0.85 s f c'
 ACI 2002 STM Model
The strength of a longitudinally reinforced strut is:
Fns  f cu Ac  As f s
' '

The nominal strength of a tie shall be taken as:

Fnt  A f  A f  f 
st y ps se p

The nominal compression strength of a nodal zone shall be:

Fnn  f A
cu n
 Findings of STM Model
The STM formulation that requires the least
volume of steel will be the solution that best
models the behavior of a concrete member
This approach holds great promise for DOTs
and design offices which could develop or
obtain standard STMs for certain commonly
encountered situations
Standard reinforcement details based on an
STM could be developed for common situations
The STM then could be reviewed and revised if
any parameters change
Thank You