Cios Select

Software
System
VA10 Software Installation

Answers for life.

2 Document Version / Disclaimer / Copyright

Document Version
Siemens reserves the right to change its products and services at any time.
In addition, manuals are subject to change without notice. The hardcopy documents cor‐
respond to the version at the time of system delivery and/or printout. Versions to hard‐
copy documentation are not automatically distributed.
Please contact your local Siemens office to order a current version or refer to our website
http://www.healthcare.siemens.com.

Disclaimer
Siemens provides this documentation “as is” without the assumption of any liability under
any theory of law.
The content described herein requires superior understanding of our equipment and may
only be performed by qualified personnel who are specially trained for such installation
and/or service.

Copyright
“© Siemens, 2015” refers to the copyright of a Siemens entity such as:
Siemens Healthcare GmbH - Germany
Siemens Aktiengesellschaft - Germany
Siemens Shenzhen Magnetic Resonance Ltd. - China
Siemens Shanghai Medical Equipment Ltd. - China
Siemens Medical Solutions USA Inc. - USA
Siemens Healthcare Diagnostics Inc. - USA and/or
Siemens Healthcare Diagnostics Products GmbH - Germany

Cios Select XPR2-140.816.01.01.02 Page 2 of 55 © Siemens, 2015

01.16 SSME CS PLM
 Table of Contents 3

1 Software Installation 4

1.1 Manufacturer’s Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.1.1 How to use these instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1.2 Screenshots & graphics in this document . . . . . . . . . . . . . . . . . . . 4
1.1.3 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.2 Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2.1 Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2.2 Starting the service software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2.3 Reading out the service key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.2.4 Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.2.5 Making a note of the customer data . . . . . . . . . . . . . . . . . . . . . . . 7
1.2.6 Uninstalling system management. . . . . . . . . . . . . . . . . . . . . . . . . 12
1.3 Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.3.1 Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.3.2 New installation of software without partitioning of the HD . . . . 16
1.3.3 New installation of software, including partitioning of the HD . . 16
1.3.4 Copying the image contents to the system partition . . . . . . . . . . 17
1.4 Starting the service software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
1.5 Reestablishing the system configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
1.5.1 Restoring the backup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
1.5.2 Firmware upgrade (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
1.5.3 Image rescue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
1.5.4 Reconfiguring the SRS location . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
1.5.5 Internet Based Connection (IBC) . . . . . . . . . . . . . . . . . . . . . . . . . . 34
1.5.6 Reinstalling system management . . . . . . . . . . . . . . . . . . . . . . . . . 37
1.5.7 Reinstalling service online help and online user manuals. . . . . . . 44
1.5.8 Installing the service CDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
1.5.9 Local printer installation (optional). . . . . . . . . . . . . . . . . . . . . . . . 44
1.5.10 Final work steps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
1.5.11 Setting the language for the keyboard and for the customer 45
user interface (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.5.12 Reconfiguring the link speed of the network interface card . . . . . 48
1.5.13 Reconfiguring the “DICOM Net” network settings. . . . . . . . . . . . . 48
1.5.14 Reconfiguring the time zone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
1.5.15 Restoring the HIPAA backup (optional) . . . . . . . . . . . . . . . . . . . . . 48
1.5.16 Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
1.5.17 Restoring available RUH packages. . . . . . . . . . . . . . . . . . . . . . . . . 48
1.5.18 Recovery image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

2 Local printer installation (option) 50

2.1 General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

2.2 Reconfiguring the local Sony UP-971AD / 991AD /D898MD printer (option‐ 51
al) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3 Changes to previous Version 53

4 List of Hazard IDs 54

© Siemens, 2015 XPR2-140.816.01.01.02 Page 3 of 55 Cios Select

01.16 SSME CS PLM
4 1 Software Installation

1.1 Manufacturer’s Note

1.1.1 How to use these instructions

System knowledge (training, online help), knowledge of Windows 7 and patience
are required for the following work steps.
You will be successful only if you follow these instructions step by step and do not
skip any points.
n Please first read the entire paragraph in advance to have a better understanding
of the work steps.
n Go back to the beginning of the paragraph and follow the instructions step by
step.

1.1.2 Screenshots & graphics in this document

Screenshots and graphics used in this document should be viewed as examples only.
They cannot describe all possible input combinations; they have an informative character
and are used only for better orientation.
The actual parameters that must be configured can either be found in the text and the
tables or they depend on the requirements and configuration (items included in the ship‐
ment) of the individual system.

1.1.3 Introduction

This document describes the software installation procedure for Cios Select systems on a
Celsius W530 PC. It is valid only for the SW versions mentioned on the cover sheet. Usu‐
 ally software installation using the system SW DVD is not necessary since the re-installa‐
tion is performed using the COBR Tool. See the Cios Select CB-DOC, chapter installation /
FLUOROSPOT Compact / Software on the CS Intranet (Print Number AX41-060.816.14).

To install the software, you will need the corresponding system SW installation DVD,
which is not included in the system shipment. Check the spare parts catalog for the appli‐
cable version of your system.

Cios Select XPR2-140.816.01.01.02 Page 4 of 55 © Siemens, 2015

01.16 SSME CS PLM
 Software Installation 1 5

1.2 Preparations

1.2.1 Prerequisites

Make sure that there is an up-to-date recovery image of the system partition.

 If necessary, create a recovery image of the system partition; refer to ( Recovery im‐
age / Page 49).

n Switch the system OFF.

n Connect the trolley to the main unit (plug in the SG cable).
n Switch the system ON.

1.2.2 Starting the service software

Starting the service software on the Cios Select system
n With the system powered up, press the<Settings>
icon on the plastic foil keyboard
n The following screen is displayed in the top left corner of the live display
( Fig. 1 Page 6).
n Press the service login icon ( 1/Fig. 1 Page 6) to display the SSW login page
( Fig. 15 Page 21).
Starting the service software in an error situation
n If XCS communication between the FL-C and XCU is interrupted, the service tab card
can be activated as follows:
- Click in the control area of the live display.
The control area is the small portion on the left side of the live display.
- Simultaneously press the <Ctrl> <Shift> <M> keys.
 The service software can be activated by clicking on the service login icon,
( 1/Fig. 1 Page 6)

© Siemens, 2015 XPR2-140.816.01.01.02 Page 5 of 55 Cios Select

01.16 SSME CS PLM
6 1 Software Installation

Fig. 1: Service login

(1) Service login icon

1.2.3 Reading out the service key

n Since the service key is not restored automatically, it must be read out manually prior
to installing the software.
- At the service software login, read out the service key and make a note of it in the
table below .( Tab. 1 Page 6)
- Start the service software, see ( Starting the service software / Page 5).
Tab. 1 Service key

14 digits 6 digits

Cios Select XPR2-140.816.01.01.02 Page 6 of 55 © Siemens, 2015

01.16 SSME CS PLM
 Software Installation 1 7

1.2.4 Backup

1.2.4.1 HIPAA backup

n If you have the HIPAA option installed, in cooperation with the network administrator
make sure that an up-to-date backup of the HIPAA users exists.

1.2.4.2 System backup

n Perform the following work steps to generate an up-to-date system backup.
- Select <Backup & Restore> from the service software main menu
( Fig. 17 Page 22).
 The Backup & Restore page appears.
- Select <Backup>.
- From the Backup Medium: list box, select <Local>.
- - Press the <Go> button to start the backup routine.
 The backup may take a couple of minutes.
 During the backup routine, status messages are displayed in the progress win‐
dow.
- Press <Exit> to return to the SSW main menu.

1.2.5 Making a note of the customer data

1.2.5.1 Reading out the link speed of the primary network interface card
n Simultaneously press the <Ctrl> <Esc> keys.
 The Windows Start menu appears.
- Press the <Control Panel> button.
n Click on <Control Panel Home> on the control panel (top left).
Then select View by: small icons from the pull-down menu in the top right corner, if
View by: small icons is not already displayed.
- Type in network ↵ in the search screen (top right).
 The search results will be narrowed and displayed.
- Click on View Network Connections.
- Double-click on DICOM Net.
- Select <Configure ...> in the DICOM Net Properties window.
- Click on the <Link Speed> tab in the window that pops up next.
- Check for <Speed and Duplex>.
- Make a note of the entry for the link speed in ( Tab. 2 Page 8).
- Close the <Intel(R) Ethernet Connection I217-LM Properties> window with <OK>.

© Siemens, 2015 XPR2-140.816.01.01.02 Page 7 of 55 Cios Select

01.16 SSME CS PLM
8 1 Software Installation

Tab. 2 Network properties

Link speed

1.2.5.2 Reading out the “DICOM Net” network settings

When reconfiguring the settings later on (after SW installation), make a note of the fol‐


lowing:
Instructions for opening the DICOM Net Properties window can be found here:
( Reading out the link speed of the primary network interface card / Page 7)

n Double-click on DICOM Net.

 The DICOM Net Properties window appears.
n Double-click on Internet Protocol Version 4 (TCP/IPv4).
 The Internet Protocol Version 4 (TCP/IPv4) Properties dialog box opens.
n Make a note of the default gateway and the DNS server addresses in the table below
( Tab. 3 Page 8).
Tab. 3 Server addresses

Default gateway _____ . _____ . _____ . _____

Preferred DNS server _____ . _____ . _____ . _____
Alternate DNS server _____ . _____ . _____ . _____

n Press the <Advanced> button.

 The Advanced TCP/IP Settings window appears ( Fig. 2 Page 9).
n Click on the <DNS> tab.

Cios Select XPR2-140.816.01.01.02 Page 8 of 55 © Siemens, 2015

01.16 SSME CS PLM
 Software Installation 1 9

n Make a note of the settings in the table below ( Tab. 4 Page 9).
Fig. 2: Advanced TCP/IP Settings_DNS

Tab. 4 Advanced DNS settings

Append primary and connection specific OFF / ON radio button

DNS suffixes
Append parent suffixes of the primary DNS Check box UNCHECKED / CHECKED
suffix
Append these DNS suffixes (in order): OFF / ON radio button
___________________________________
___________________________________
___________________________________
DNS suffix for this connection: ________________________________

© Siemens, 2015 XPR2-140.816.01.01.02 Page 9 of 55 Cios Select

01.16 SSME CS PLM
10 1 Software Installation

Register this connection’s addresses in DNS Check box UNCHECKED / CHECKED

Use this connection’s DNS suffix in DNS reg‐ Check box UNCHECKED / CHECKED
istration

n Close all open windows and go back to the control panel home menu.

1.2.5.3 Reading out the time zone

n Go back to the control panel home menu.
n Then select View by: small icons from the drop-down menu in the top right corner if
View by: small icons is not already displayed).
n Click on the <Date and Time> icon.
 The Date and Time window appears.
n Note the Time Zone in the table, e.g. (UTC -6.00) Central Time (US & Canada)
( Tab. 5 Page 10).
n Close the Date and Time window.
n Close the Control Panel.
Tab. 5 Time zone

Time zone

1.2.5.4 Reading out the SRS location

1. Select <FLC Service> <Configuration> <SRS Configuration> <Central SRS Configu‐

ration> from the SSW Main menu.
2. Click on <Continue>.
 The Central SRS Configuration page is displayed.
3. Make a note of the Location in the table, e.g. America ( Tab. 6 Page 10).
Fig. 3: Activate the IE Proxy configuration from the Central SRS Configuration page

Tab. 6 SRS location

Location

Cios Select XPR2-140.816.01.01.02 Page 10 of 55 © Siemens, 2015

01.16 SSME CS PLM
 Software Installation 1 11

4. Go back to the SSW main menu.

1.2.5.5 Checking internet-based connection (IBC) for SRS

Perform the following check to determine whether IBC is used:
n Start the FL-C SSW and select <Configuration> <Central SRS Configuration>.
 The system management install.log appears.
- Check in the line Internet-based Connectivity: whether installed is displayed for
the status.
- Mark the appropriate check box in ( Tab. 7 Page 11).
Tab. 7 Internet-based connectivity

IBC used Yes No

Q Q

n Return to the FL-C SSW main menu.

Fig. 4: Checking whether IBC is used

© Siemens, 2015 XPR2-140.816.01.01.02 Page 11 of 55 Cios Select

01.16 SSME CS PLM
12 1 Software Installation

1.2.6 Uninstalling system management

n System management needs to be uninstalled, e.g. prior to every update of the System
SW or prior to when the host name needs to be changed for any reason.
- Select <Configuration> <System Management> in the FL-C SSW.
- Close the system management install.log window with <Continue>.
- Activate the Uninstallation check box H and then press the <Go> button to trig‐
ger the uninstallation.
 The uninstallation process is displayed in a new window.
 Uninstallation may take up to 10 minutes; do not interfere with the uninstalla‐
tion by pressing any other buttons!
 Please wait patiently until the <Continue> button is displayed at the lower right
corner of the browser window.

Fig. 5: System Management - Deinstallation is selected

- Press <Continue> when uninstallation is complete and the system management in‐
stall.log is displayed ( Fig. 37 Page 39).
- A reboot request is displayed on the following page, see ( Fig. 6 Page 13).
 Confirm the reboot request with <OK>.
 The FL-C will reboot.

Cios Select XPR2-140.816.01.01.02 Page 12 of 55 © Siemens, 2015

01.16 SSME CS PLM
 Software Installation 1 13

Fig. 6: System Management uninstalled, reboot request

Uninstallation Successful
n Following the reboot, again select <Configuration> <System Management> in the
FL-C service mode.
n No check boxes for Installed and Activated may be selected and the status
must be set to not installed.
n No template version may be displayed under Template update.
 System management has been uninstalled successfully.
n Exit the service mode.
n Switch OFF the system.
n If support is necessary, contact the SRS Help Desk( Tab. 8 Page 13).
Tab. 8 SRS Help Desk

SRS Help Desk Worldwide SRS Help Desk USA (only)

Service days Monday - Friday. Monday - Friday.
Service hours 24 hrs. 8:30 AM - 7:00 PM EST
Phone +49 9191 18 8080, Code 1-9-1 + 1 800 576 7336, Code 2-3-13

© Siemens, 2015 XPR2-140.816.01.01.02 Page 13 of 55 Cios Select

01.16 SSME CS PLM
14 1 Software Installation

SRS Help Desk Worldwide SRS Help Desk USA (only)

FAX +49 9131 84 13 7388 n.a.
E-mail [email protected] [email protected]

Cios Select XPR2-140.816.01.01.02 Page 14 of 55 © Siemens, 2015

01.16 SSME CS PLM
 Software Installation 1 15

1.3 Software Installation

1.3.1 Preparations

With a Celsius W530 PC, the boot menu is always enabled and is accessible using the F12

 key, but is password-protected.

After the reboot password is entered, the boot priority can be changed.

1.3.1.1 Booting the system DVD

n Switch OFF the system.
n Switch ON the system.
n The PC will now start to reboot.
- Press the <F12> key several times while the FL-C reboots.
n A pop-up appears that prompts the user to enter the password. It is the same as the
reboot password. See the corresponding entry in the XP password list (Doc ID
SKB0005932), which is published in the CS knowledge base.
n In the Boot Menu that follows, select <P4: TSSTcorp ...> by using the arrow keys.
n Insert the first software installation medium into the DVD drive and wait until the LED
on the drive stops blinking.
n Press the return key to confirm.
 The PC will now reboot from the DVD.
 Windows PE starts and Windows is Loading files ... is displayed on the screen.
 A command window opens and several boot-up messages are displayed.
 Be patient!

 A section window appears. Please select your system and confirm.

Fig. 7: Cios system selection

 Finally, the SW Installation window appears, ( Fig. 8 Page 16).

© Siemens, 2015 XPR2-140.816.01.01.02 Page 15 of 55 Cios Select

01.16 SSME CS PLM
16 1 Software Installation

Fig. 8: FL-C software installation

- Load application
This option is used if you need to install only the operating system and the application.
The second partition of the HD with the medical studies is not affected. The existing
medical studies are retained. Continue at ( New installation of software without parti‐

 tioning of the HD / Page 16).

- Prepare hard disk + load application (clean installation)
This option is used if you want to install the entire application, the operating system and
an empty image partition. If you choose this option, you will lose your medical studies.
Continue at( New installation of software, including partitioning of the HD / Page 16).

1.3.2 New installation of software without partitioning of the HD

The patient studies will not be deleted!
n Click on <Load application>, which is the default and continue with <OK>
( Fig. 8 Page 16).
n Continue with ( Copying the image contents to the system partition / Page 17).

1.3.3 New installation of software, including partitioning of the HD

n Click on <Prepare HD and Load Application>.
n Reenter the reboot password and click on <OK> to start the process
( Fig. 9 Page 16).
Fig. 9: Entering the password dialog

After a few seconds, a new window comes up displaying the installation progress.

Cios Select XPR2-140.816.01.01.02 Page 16 of 55 © Siemens, 2015

01.16 SSME CS PLM
 Software Installation 1 17

n Continue with( Copying the image contents to the system partition / Page 17).

1.3.4 Copying the image contents to the system partition

n A new window appears and displays the installation progress ( Fig. 10 Page 17).

The SW installation and subsequent component download process may take up to 80

minutes. During that time, no mouse / keyboard activity is necessary (except when in‐
serting the second installation medium).
The window ( Fig. 10 Page 17) will be displayed for approximately 30 minutes.
After approx. 10 minutes, a pop-up appears. It will prompt you to insert the second (also


approx. 10 min.) and later the third installation medium.
Follow the instructions on the screen accordingly.
Do not remove the SW DVD until you are prompted to insert the second medium. Once
the download process has ended, the FL-C remains in the boot-up screen
( Fig. 11 Page 18).
Do not remove the last installation medium unless the FL-C has finally booted up to the
boot-up screen!!

Fig. 10: Copy Ghost

n For your information:

After the ghost files have been copied to the HDD, an automatic reboot is performed:
- Setup starts, “Services & Devices” is displayed.
- The second display is initialized.
- Setup is applying system settings is displayed.
 Another reboot is performed.
 The Win 7 boot screen comes up.
 Another reboot is performed.
- Several msi installer packages will be installed; this will take a while.
 Another reboot is performed.

© Siemens, 2015 XPR2-140.816.01.01.02 Page 17 of 55 Cios Select

01.16 SSME CS PLM
18 1 Software Installation

- A command window will open, the XCU, several components (C-Arm control panel/
Trolley control panel), firmware downloads of drives, and the generator download
will be performed. This procedure may take up to 30 minutes!
 Finally another reboot is performed.
 This is the end of the SW installation procedure.
n When finished, the FL-C application boot up( Fig. 11 Page 18).
 Remove the software installation DVD from the drive.
n Switch OFF the system and wait until the system has shut down.
Fig. 11: Cios select bootup

n Switch the system ON again.

 The PC reboots again and displays the boot-up screen.

Cios Select XPR2-140.816.01.01.02 Page 18 of 55 © Siemens, 2015

01.16 SSME CS PLM
 Software Installation 1 19

1.4 Starting the service software

English is set as the default layout for the keyboard. ( Fig. 12 Page 19) shows the
 English layout for the keyboard. This is intended to serve as an aid in finding keys if the
existing keyboard does not have the English layout.

Fig. 12: Default keyboard layout

The system must be booted and the application software started to start the service soft‐
ware.
n Start the SSW as described here ( Starting the service software / Page 5).
n Two user messages may possibly appear, ( Fig. 13 Page 20) and
( Fig. 14 Page 20).
 Close them with <Cancel>.

© Siemens, 2015 XPR2-140.816.01.01.02 Page 19 of 55 Cios Select

01.16 SSME CS PLM
20 1 Software Installation

Fig. 13: License file not detected Fig. 14: Service key not detected

n At the SSW login page, ( Fig. 15 Page 21):

- Mark the HSet as default check box, ( 1/Fig. 15 Page 21).
- Enter the first 14 digits of the service key you noted in( Tab. 1 Page 6) in the left
input box ( 2/Fig. 15 Page 21).
- Click on the right input box ( 3/Fig. 15 Page 21).
- Enter the last six digits of the service key you noted in ( Tab. 1 Page 6).

Cios Select XPR2-140.816.01.01.02 Page 20 of 55 © Siemens, 2015

01.16 SSME CS PLM
 Software Installation 1 21

- Press the <OK> button to login.

Fig. 15: Service software, login

2 3

n If a pop-up appears, ( Fig. 16 Page 21), close it with <OK>.

Fig. 16:

© Siemens, 2015 XPR2-140.816.01.01.02 Page 21 of 55 Cios Select

01.16 SSME CS PLM
22 1 Software Installation

n If a valid service password has been entered correctly, the service software main
menu ( Fig. 17 Page 22) appears.

 Ignore config check and version check warnings. They will be done later.

Fig. 17: Service software, Main menu

n For information only:

Cios Select XPR2-140.816.01.01.02 Page 22 of 55 © Siemens, 2015

01.16 SSME CS PLM
 Software Installation 1 23


The FL-C SSW( Fig. 18 Page 23) is started by clicking on the <FL-C Service> button in
( Fig. 17 Page 22).

Fig. 18: FL-C service software, Main menu

© Siemens, 2015 XPR2-140.816.01.01.02 Page 23 of 55 Cios Select

01.16 SSME CS PLM
24 1 Software Installation

1.5 Reestablishing the system configuration

1.5.1 Restoring the backup

Restore the most recent system backup as follows.
n From the service software main menu, select <Backup/Restore>.
- The FL-C Backup / Restore window appears.
- Click on the <Restore> button.
 The restore files page is displayed ( Fig. 19 Page 24).
- From the Select drive: list box, select <2nd HDD>.
- Select the last backup that was made from the packages list.
- Press the <Go> button to start the restore routine.
- Confirm all the safety inquiries that follow with <OK> or <Yes>.

Fig. 19: SSW: Backup & Restore, selecting the restore package

Cios Select XPR2-140.816.01.01.02 Page 24 of 55 © Siemens, 2015

01.16 SSME CS PLM
 Software Installation 1 25

n Once the restore has finished, the Distribute Restored Files dialog appears
( Fig. 20 Page 25).
Fig. 20: SSW: Backup & Restore, Distribute Restored Files

- In the action bar, press <Select All> to select all subcomponents.

 All checkboxes are marked, H.
- Press <Go> to copy the configuration files to their working directories.

 Patience is required. The restore process may take up to 20 minutes.

- Wait until all configuration files are sent to the sub-components.

 Each subcomponent states completed when distribution is completed.
- Confirm the request for Config Check and wait until it has ended.
 Config Check will run automatically.
- Run Config Check and / or Auto Conf if necessary / requested.
- Close the Config Check / Auto Conf page with <Exit>.
- Press <Home> to return to the service software main menu

© Siemens, 2015 XPR2-140.816.01.01.02 Page 25 of 55 Cios Select

01.16 SSME CS PLM
26 1 Software Installation

- Confirm the request for Version Check and wait until it has ended
 Version Check will run automatically
During a regular SW installation or upgrade, the FW/SW of generator board D610 and


D611 will not upgrade. As a work around, they must be upgraded manually via gener‐
ator service programs. Please pay special attention to the part “Component: Genera‐
tor_Get”( Fig. 21 Page 26) in Version Check result.

Fig. 21: Version check result

- Close the Version Check page with <Exit>.

- Ignore the Reboot Required message.
n Press <Home> to return to the service software main menu.
n Only when the part “Component: Generator_Get” in the Version Check result shows
a status of “different”, should you do the firmware upgrade via Generator service pro‐
grams. For details, refer to ( Firmware upgrade (optional) / Page 26)
n Close the service software with <Logout>.
 A pop-up may appear, SIEMENS FLC_V7 has stopped working. Confirm it by
clicking on <Close the program>.
n Switch the system OFF and and then back ON again twice!
Each time, wait for the system to shut down and then reboot completely.

1.5.2 Firmware upgrade (optional)

1.5.2.1 Generator service switch

 To do firmware upgrade, the hardware switch “SERV” switch must be in position “2”. The
switch is located in the D610 board.

Cios Select XPR2-140.816.01.01.02 Page 26 of 55 © Siemens, 2015

01.16 SSME CS PLM
 Software Installation 1 27

Fig. 22: D610

© Siemens, 2015 XPR2-140.816.01.01.02 Page 27 of 55 Cios Select

01.16 SSME CS PLM
28 1 Software Installation

Fig. 23: SERV switch

Cios Select XPR2-140.816.01.01.02 Page 28 of 55 © Siemens, 2015

01.16 SSME CS PLM
 Software Installation 1 29

1.5.2.2 Start the generator service programs for firmware upgrade

Access the generator service programs

1. Login in service software.

2. Access to FLC Service -> System -> System Boot.
3. Click on the button <Exit to OS> to call up the password dialog. Enter the password
and click on <Go>. The password list is published in the CS knowledge base.
 The FLC application is closed and Windows desktop appears.
4. Click on Windows start menu, and select Windows Explorer
5. Access to the folder C:\FLC\Addon\MobilGenerator\LocalApplication.
6. Double-click “LocalApplication.exe”
 The Generator service program starts

Generator service program start screen

The Generator service program start screen:

1. The “User” option is for “Configuration Settings” only (the default display)
2. Select “Technical Service” and click inside the password field.
 An onscreen keyboard will open( Fig. 26 Page 31)
3. Enter the service password
4. Complete generator services are available.( Fig. 25 Page 30)

© Siemens, 2015 XPR2-140.816.01.01.02 Page 29 of 55 Cios Select

01.16 SSME CS PLM
30 1 Software Installation

Fig. 24: Generator service start screen

1
3
2

(1) User option

(2) Technical Service option
(3) Password
(4) Service tabs

Fig. 25: Complete generator service

Cios Select XPR2-140.816.01.01.02 Page 30 of 55 © Siemens, 2015

01.16 SSME CS PLM
 Software Installation 1 31

Fig. 26: Password input window

1.5.2.3 Firmware upgrade

Procedure for upgrade FW of D610 board
n Click on Firmware Upgrade( Fig. 27 Page 31)

Fig. 27: Firmware upgrade

 A black window will be displayed. Navigation is similar to Windows Explorer.

Perform this step-by-step for each board.

© Siemens, 2015 XPR2-140.816.01.01.02 Page 31 of 55 Cios Select

01.16 SSME CS PLM
32 1 Software Installation

n Navigate to and select the board FW file of D610( Fig. 28 Page 32)
Fig. 28: D610 upgrade

n Click Start ETH Upgrade button.

 A new window comes up displaying the progress of the upgrade. This window
will close automatically after upgrade has finished.( Fig. 29 Page 32)

Fig. 29: Firmware upgrade on-going

 Do not touch any function button while the procedure is running.

Cios Select XPR2-140.816.01.01.02 Page 32 of 55 © Siemens, 2015

01.16 SSME CS PLM
 Software Installation 1 33

n Wait until the upgrade is complete. Click Exit.

n Restart the entire system.
n Log into the SSW ->Configuration-> Version Check. Do version check again.
n Check whether installation was successful.

1.5.3 Image rescue

n Start the SSW.
n If requested, run Version Check.
n From the FL-C SSW, select <System>
n Choose <Image Rescue> from the tree browser on the left.
n Press the <Image Rescue> button and answer the requester with <OK>.
 After a few seconds, the message Image save completed successfully
is displayed.
 The patient database is rebuilt.

1.5.4 Reconfiguring the SRS location

n Select <FLC Service> <Configuration> <SRS Configuration> <Central SRS Configu‐
ration> from the SSW Main menu.
n Click on <Continue>.
 The Central SRS Configuration page is displayed.

 Due to a bug in the VA10 software, the following work-around is required for reconfigur‐
ing the Location.

n Select another Location, different from the one shown AND different from the one
originally written down ( Tab. 6 Page 10).
Fig. 30: Activate the IE Proxy configuration from the Central SRS Configuration page

n Click <Save> in the action bar.

 The message “SRS configuration updated successfully” is displayed in the ac‐
tion bar.

© Siemens, 2015 XPR2-140.816.01.01.02 Page 33 of 55 Cios Select

01.16 SSME CS PLM
34 1 Software Installation

 This is the end of the workaround.

n Select the location originally written down ( Tab. 6 Page 10).

n Click on <Save> in the action bar.
 The message “SRS configuration updated successfully” is displayed in the ac‐
tion bar.
n Go back to the SSW main menu.

1.5.5 Internet Based Connection (IBC)

An internet-based connection is an alternative SRS connection method via the Digital

Subscriber Line (DSL).

 For initial setup of the internet-based connection, refer to the SRS configuration docu‐
ment, XP00-SRS.843., in the corresponding product CB-DOC (Service - Siemens Remote
Service - SRS - Configuration).

A new one-time password (OTP) is required to re-establish the SRS connection using in‐

 ternet based connection (IBC)!

The new OTP can be obtained from the SRS Help Desk.


To set up the internet based connection, you need to contact the SRS Help Desk
( Tab. 10 Page 37).

This configuration will establish an SSL tunnel through the hospital network directly into
the Internet via outgoing TCP port 443.

 Not all countries allow direct access (outgoing via TCP port 443) into the Internet --> part
of the clarification process using the SRS configuration management checklist.

Setting up the internet-based connection

n Start the SSW.
n Go to <Configuration> <Site Info>.
n Record the system material number and serial number.
n Call the SRS Help Desk to obtain a One Time Password (OTP) ( Tab. 10 Page 37).
n Start the FL-C SSW.
n Select <Configuration> from the main menu.
- Choose <SRS Configuration> <internet based connection> from the tree browser
to the left.
 The internet based connection main page is displayed:

Cios Select XPR2-140.816.01.01.02 Page 34 of 55 © Siemens, 2015

01.16 SSME CS PLM
 Software Installation 1 35

Fig. 31: Internet Based Connection

1 3

(1) Tab card "Internet Based Connection" (IBC)

(2) Check box for IBC activation
(3) Input field for One Time Password (OTP)
(4) Check box to activate tunnel by default

- Activate the IBC check box, see ( 2/Fig. 31 Page 35).

- Enter the One-Time Password (OTP) provided by the SRS Help Desk (via e-mail or
the hand-held) in the OTP screen, see ( 3/Fig. 31 Page 35).
- Check whether the tunnel check box is activated (activated by default), see
( 4/Fig. 31 Page 35).
- Press the <GO> button.
 The IBC installation will be started with status messages in the output window.
 When the installation is finished, click on Next.
 WARNING
Once the internet based connectivity is installed, do not unmark the check box
The password given by the SRS Help Desk is valid only one time!
 If you need to uninstall then install the internet based connection, you will
have to contact the SRS Help Desk( Tab. 10 Page 37) to get a new pass‐
word.

n The installation is successful: e.g., IP address 14.251.0.43

 The IBC status is set to “installed”,
see ( 1/Fig. 32 Page 36).
 The IBC SSL tunnel IP address, see ( 1/Fig. 33 Page 36),
is visible in the “System Management” window, see ( 2/Fig. 32 Page 36),
and begins with 14.251.xx.xx.

© Siemens, 2015 XPR2-140.816.01.01.02 Page 35 of 55 Cios Select

01.16 SSME CS PLM
36 1 Software Installation

Fig. 32: IBC status "installed" in window "System Management"

(1) IBC status = installed

(2) IBC SSL tunnel IP address

Fig. 33: IBC SSL tunnel IP address in cRSP

(1) IBC SSL tunnel IP address in cRSP

n The installation failed:

 The IBC SSL tunnel IP address beginning with 14.251.xx.xx is not visible in the
“System Management” window.

Troubleshooting:
- Enter the service menu and log in with the service key
- Press CTRL+ESC
 The Windows Start menu will open.
- Click on the menu Programs --> Command prompt
 A command box opens.
- Test the connection to the IBC SSL server with a telnet command,
see ( Tab. 9 Page 37).
 If there is a successful connection, no errors will be displayed
(empty black window)
 If there is an unsuccessful connection, the message “connect failed” will be dis‐
played.
Contact the SRS Help Desk, see ( Tab. 10 Page 37)if you get this error result.

Cios Select XPR2-140.816.01.01.02 Page 36 of 55 © Siemens, 2015

01.16 SSME CS PLM
 Software Installation 1 37

Tab. 9 IBC troubleshooting with telnet commands

SRS Center Test to SSL server

Telnet command in a command box
Europe Telnet_194.138.37.194_443
America Telnet_12.46.135.194_443
Asia Telnet_194.138.240.119_443
Test Telnetτ_194.138.37.193_443

Tab. 10 SRS Help Desk

SRS Help Desk Worldwide SRS Help Desk USA (only)

Service days Monday - Friday. Monday - Friday.
Service hours 24 hrs. 8:30 AM - 7:00 PM EST
Phone +49 9191 18 8080, Code 1-9-1 + 1 800 576 7336, Code 2-3-13
FAX +49 9131 84 13 7388 n.a.
E-mail [email protected] [email protected]

1.5.6 Reinstalling system management

Prerequisite for the following configuration steps for system management is that the SRS
router is set up correctly (refer to the corresponding system startup instructions). Other‐

 wise the system management installation will fail.

This document is N O T intended for initial SRS setup. For this, see the corresponding in‐
stallation and startup instructions (XP00-SRS.843.02)!

These instructions are not applicable for initial system management installation.

 The following paragraph describes how to restart system management if it was previous‐
ly in use.

1.5.6.1 Activating system management

n Select <Configuration><SRS Configuration> <System Management> in the FL-C
service software main menu.


Every time <System Management > is selected, the system management install.log is up‐
dated and displayed in the browser window ( Fig. 34 Page 38).

- Press <Continue> to proceed ( Fig. 34 Page 38).

© Siemens, 2015 XPR2-140.816.01.01.02 Page 37 of 55 Cios Select

01.16 SSME CS PLM
38 1 Software Installation

Fig. 34: FL-C SSW, Configuration, System Management install.log

n At the top of the page the Location, which was already configured under Central SRS
Configuration, is displayed automatically and appears dimmed.
n The IP address of the DICOM Connection that was configured under network setting
(control panel) is displayed under Network Adapter TCP/IP address
( Fig. 35 Page 38).

 If Outside NAT is configured, the IP addresses for Event Mgmt. and SW distribution server
are also displayed (the screen shot below shows only an example!).

Fig. 35:

Cios Select XPR2-140.816.01.01.02 Page 38 of 55 © Siemens, 2015

01.16 SSME CS PLM
 Software Installation 1 39

n To test the connectivity, press the <Ping> button. Since this is a very time-critical ac‐
tion, it is possible that a connection will not be immediately established. Because of
this, several attempts should be made.
The server must send back a message displayed in the status bar:
Fig. 36: Pinging the System Management server

n Starting the installation / registration process

- If system management is not installed, the system management page is displayed
as shown in ( Fig. 38 Page 41).
- Activate the Installation & Registration check box.
 The Activation check box will be activated automatically.
- Simply start the installation / registration process by pressing <Go>.
 The installation / registration process is displayed in a new window and may
take up to 20 minutes and runs automatically.

Fig. 37: System Management,— installation / uninstallation

- Once the installation / registration process has finished, the system management in‐
stall.log is displayed( Fig. 37 Page 39).
 Press <Continue>, ( Fig. 37 Page 39).
-
The status of the MNP is as shown in( Fig. 39 Page 41).
Checking the installation

© Siemens, 2015 XPR2-140.816.01.01.02 Page 39 of 55 Cios Select

01.16 SSME CS PLM
40 1 Software Installation

n The following conditions must be met ( Tab. 11 Page 40):

- Select <System><SRS Configuration><System Management> in the FL-C service
software.
Tab. 11 System Management successfully installed

Function Installation & Offline in‐ Uninstal‐ Current state

registration stallation lation
System management H Q Q Installed
base
Activation active
H
Template Update Template version,
Q e.g. 1.13


If the installation / registration fails, a rollback to an offline Iinstallation is performed,
see ( Fig. 41 Page 41).

Following a failed installation and subsequent rollback to an offline installation, an ad‐

 ditional attempt to install should be made. If this attempt also fails, contact the SRS
Help Desk.

Tab. 12 SRS Help Desk

SRS Help Desk Worldwide SRS Help Desk USA (only)

Service days Monday - Friday. Monday - Friday.
Service hours 24 hrs. 8:30 AM - 7:00 PM EST
Phone +49 9191 18 8080, Code 1-9-1 + 1 800 576 7336, Code 2-3-13
FAX +49 9131 84 13 7388 n.a.
E-mail [email protected] [email protected]

n The illustration( Fig. 39 Page 41) shows an example of the system management
page following a successful installation & registration / activation. An appropriate tem‐
plate is present on the FL-C.

Cios Select XPR2-140.816.01.01.02 Page 40 of 55 © Siemens, 2015

01.16 SSME CS PLM
 Software Installation 1 41

Different status of system management installation

n The screen shots below represent the different statuses of the MNP:
- System management not installed

Fig. 38: System Management not installed

- System Management installed and activated

Fig. 39: System Management installed and activated

- System management installed and deactivated (e.g. for troubleshooting purposes)

Fig. 40: System Management installed and deactivated

- Offline installation

Fig. 41: System Management, offline installation

© Siemens, 2015 XPR2-140.816.01.01.02 Page 41 of 55 Cios Select

01.16 SSME CS PLM
42 1 Software Installation

Uninstalling system management

n System management needs to be uninstalled, e.g. prior to every update of the system
SW or prior to when the host name needs to be changed for any reason.
- Select <Configuration> <System Management> in the FL-C SSW.
- Close the System Management install.log window with <Continue>.
- Activate the Deinstallation check box H and then press the <Go> button to trigger
the uninstallation.
 The uninstallation process is displayed in a new window.
 Uninstallation may take up to 10 minutes; do not interfere with the uninstalla‐
tion by pressing any other buttons!
 Please wait patiently until the <Continue> button is displayed at the lower right
corner of the browser window.

Fig. 42: System Management - Deinstallation is selected

- Press <Continue> when uninstallation is complete and the system management in‐
stall.log is displayed ( Fig. 37 Page 39).
- A reboot request is displayed on the following page, see ( Fig. 43 Page 43).
 Confirm the reboot request with <OK>.
 The FL-C will reboot.

Cios Select XPR2-140.816.01.01.02 Page 42 of 55 © Siemens, 2015

01.16 SSME CS PLM
 Software Installation 1 43

Fig. 43: System Management uninstalled, reboot request

Uninstallation Successful
n Following the reboot, again select <Configuration> <System Management> in the
FL-C service mode.
n No checkboxes for Installed and Activated may be selected and the status
must be set to not installed.
n No template version may be displayed under Template update.
 System management has been uninstalled successfully.
n Exit the service mode.
n Switch OFF the system.
n If support is necessary, contact the SRS Help Desk ( Tab. 13 Page 43).
Tab. 13 SRS Help Desk

SRS Help Desk Worldwide SRS Help Desk USA (only)

Service days Monday - Friday. Monday - Friday.
Service hours 24 hrs. 8:30 AM - 7:00 PM EST
Phone +49 9191 18 8080, Code 1-9-1 + 1 800 576 7336, Code 2-3-13

© Siemens, 2015 XPR2-140.816.01.01.02 Page 43 of 55 Cios Select

01.16 SSME CS PLM
44 1 Software Installation

SRS Help Desk Worldwide SRS Help Desk USA (only)

FAX +49 9131 84 13 7388 n.a.
E-mail [email protected] [email protected]

1.5.7 Reinstalling service online help and online user manuals

Proceed as follows to reinstall the system online help:
n Start the service software and select <Configuration> <Local Installation>.
- Insert the <System Name> online help CS CD-ROM into the CD drive and wait until
the LED stops blinking.
- Press the <Go> button.
 A command window pops up. Enlarge it and follow the instructions on the mon‐
itor
- Remove the CD from the drive.

To reinstall the online user manuals, perform the following steps:

- Insert the online user manuals CD from the system binder into the CD drive and
wait until the LED on the drive stops blinking.
- Press the <GO> button.
Double-click on the required system type and then select the desired language
and follow the specific instructions.
- Remove the CD from the drive.

1.5.8 Installing the service CDs

n If there are patches for the FL-C application or Microsoft hot fixes available, install
them according to the appropriate UI.

1.5.9 Local printer installation (optional)

n If a local USB printer (Sony UP-971AD or UP-991AD or UP-D898MD) is connected, con‐
figure it according to ( Local printer installation (option) / Page 50).

1.5.10 Final work steps

n Check to make sure that all options for the site are available.
n Switch off the system.
n Wait until the FL-C has shut down (this may take up to 2 minutes).
n Switch on the system and wait until the FL-C application software is running.
X
n
Check for correct function of image flip in the fluoroscopy operating mode.

Cios Select XPR2-140.816.01.01.02 Page 44 of 55 © Siemens, 2015

01.16 SSME CS PLM
 Software Installation 1 45

n Check the Single Image operating mode for correct function.

n Check the Subtraction and Roadmap operating modes (optional) for correct function.
n Perform a function check of the local Sony UP-971AD /991AD /D898MDprinter (op‐
tional).
This is the end of the software installation procedure.

1.5.11 Setting the language for the keyboard and for the customer user inter‐
face (optional)

The default language (English) was set during the first part of the installation. The re‐
gional settings (keyboard layout, language for the customer UI, host name and the date

 format) are part of backup/restore.

The following pages are for information only if regional settings need to be changed for
any reason.

 Not all of the languages listed below are supported/released for all systems.

Setting the language for the customer user interface

n The following languages are supported for the user interface:
- English (US)
- German
- French
- Spanish
- Russian
- Japanese
- Chinese
n To configure the language for the customer UI and the keyboard, continue as follows:
n Start the service software and select <Configuration> <System Config>
n Click on Language Setting combo-list and choose the language in which you want to
run the customer user interface, e.g.: "German (Germany)”.
n Click on Save and then Click on Exit
n Confirm the request for Config Check and wait until it has ended.
 Config Check will run automatically.
n Run Auto Conf if necessary / requested and then Exit.
n Click on Home back to service main menu and select <FL-C Service> <System> <Sys‐
tem Settings> <Control Panel>.
n In the control panel, make sure View by: Small icons is selected in the drop down
menu.

© Siemens, 2015 XPR2-140.816.01.01.02 Page 45 of 55 Cios Select

01.16 SSME CS PLM
46 1 Software Installation

n Click on the <Regional and Languages> icon in the control panel.

 A new dialog box appears. Region and language
n Click on <Format:> in the 1st tab card (Formats). combo-list and choose the language
in which you want to run the customer user interface, e.g.: "German (Germany)".
n Confirm this new configuration by clicking on <Apply>!!!
n Make sure to click on <Apply> first!
Setting the input language (keyboard layout):
n From the FL-C point of view, the keyboard layouts (physically) for the following lan‐
guages are supported. But this does not mean that all languages are to be configured
for all systems:
- English (United States)
- German (Germany)
- French (France)
- Spanish (Spain)
- Portuguese
n Start the service software and select <Configuration> <System Config>
n Click on Keyboard Layout combo-list and choose the language in which you want to
run the keyboard, e.g.: "German (Germany)”.
n Click on Save and then Click on Exit
n Confirm the request for Config Check and wait until it has ended.
 Config Check will run automatically.
n Run Auto Conf if necessary / requested and then Exit.
n Click on Home back to service main menu and select <FL-C Service> <System> <Sys‐
tem Settings> <Control Panel>.
n In the control panel, make sure View by: Small icons is selected in the drop down
menu.
n Click on the <Region and Languages> icon in the <Control Panel>.
 A new dialog box appears. Region and language
n Click on the Keyboards and Languages tab card and then click on the <Change key‐
boards...> button.
 Afterwards, a new dialog is shown Text Services and Input Languages.
n Select the same input language (keyboard layout) that is to be selected for the cus‐
tomer UI from the Default input language combo list.
n Close the Text Services and Input Languages dialog with <OK>.
n Back in the Region and Language main dialog again, click on Administrative tab
card.
n Click on <Change system locale...>.
 Afterwards, a new dialog is shown Region and Language Settings.
n From the combo list, choose the same system locale that is to be selected for the cus‐
tomer UI

Cios Select XPR2-140.816.01.01.02 Page 46 of 55 © Siemens, 2015

01.16 SSME CS PLM
 Software Installation 1 47

n Press the <OK> button to close the dialog.

 A new dialog then appears: Change System Locale.
n Windows must be restarted. Close the window with <Restart now>.
 The FL-C will restart.
 Wait until the application has booted and the FL-C remains in the patient list.

1.5.11.1 Setting Chinese as the input locale and language for the user interface
n Configure Chinese as Language Setting and English as Keyboards layout in Service
Software <Configuration> <System Config>
n Run Config Check/Auto Conf if necessary / requested and then Exit.
n Double-click on the Regional and Language icon in the Control Panel.
- Select Chinese (Simplified, PRC) from the Format list box in Formats tab.
- Select China as the current location in Location tab.
- Select the Keyboards and Languages tab.
- Click on Change keyboards...
 The Text Services and Input Languages window will appear.
- Select Chinese (Simplified, PRC) - Chinese (Simplified) - Microsoft Pinyin New
Experience Input from the Default input language list box.
- Click on Add and add Chinese (Simplified, PRC) keyboard.
- Close the Text Services and Input Languages window with OK.
- Select the Administrative tab in the Regional and Language window.
- Click on Change system locale and select Chinese (Simplified, PRC) from the Lan‐
guage for non-Unicode programs combo box in the Regional and Languages
Setting window.
Close the window with OK.
- If a Required files are ... window appears, confirm it with Yes.
- Then the You must restart ... dialog appears. Close the window with Yes.
 The PC will reboot. After the reboot, go back to the FL-C service mode.
n Select FLC Service /System / System Settings / Control Panel in the service main
menu.
- Double-click on the Regional and Language icon.
- Select the Keyboards and Languages tab.
- Click on Change keyboards...
 The Text Services and Input Languages window appears.
- Click on Advanced Key Settings
 The Advanced Key Settings window appears.
- Make sure that the Press the CAPS LOCK key button is activated.
- Press the button Change Key Sequence ...
 The Change Key Sequence window comes up.

© Siemens, 2015 XPR2-140.816.01.01.02 Page 47 of 55 Cios Select

01.16 SSME CS PLM
48 1 Software Installation

- Unmark the Switch input languages and Switch keyboard layouts check boxes.
- Close the window with OK.
- Close all open windows and return to the FL-C service main menu.
- Exit the SSW and switch off the system.

1.5.12 Reconfiguring the link speed of the network interface card

n If the link speed of the DICOM network interface card was previously set differently
from the default, ⇒ auto, refer to( Reading out the link speed of the primary net‐
work interface card / Page 7) to reestablish the desired setting.

1.5.13 Reconfiguring the “DICOM Net” network settings

n Reconfigure the settings to the values you noted in ( Reading out the “DICOM Net”
network settings / Page 8).

1.5.14 Reconfiguring the time zone

n Reconfigure the time zone to the value you noted in ( Reading out the time
zone / Page 10).

1.5.15 Restoring the HIPAA backup (optional)

n If the HIPAA option is installed, contact the customer network administrator to restore
the HIPAA backup and the user passwords.

1.5.16 Backup
n Prepare an up to date backup ( System backup / Page 7).

1.5.17 Restoring available RUH packages

n There are certain conditions in which a RUH package that was installed previously is
no longer installed. This might be the case after:

a) Restoring a recovery image which does not contain the RUH package(s)
b) Reinstallation of the system software
c) Replacing the primary hard disk (which leads to: a) restore of a recovery image)
d) Replacing the PC (which leads to: a) restore of a recovery image)

Cios Select XPR2-140.816.01.01.02 Page 48 of 55 © Siemens, 2015

01.16 SSME CS PLM
 Software Installation 1 49

n All the RUH packages which were pushed from the remote server to the system are
archived automatically on the second hard disk (service partition) on the FL-C. The
path is Z:\MedHome\sd_store.
Fig. 44: RUH Packages on the 2nd HDD (Service Partition)

n How to find out if all available RUH packages for the system are already installed in
the current SW installation
- Open Windows explorer and navigate to Z:\MedHome\sd_store.
- Check for available (archived) RUH packages, ( Fig. 44 Page 49).
n Open a second Windows explorer and navigate to C:\MedHome\sd_store.
 If all the packages located in Z:\MedHome\sd_store are also present in C:
\MedHome\sd_store, the current SW installation is up-to-date. No further ac‐
tion is required.
 If packages are present in Z:\MedHome\sd_store which are NOT present in C:
\MedHome\sd_store, install the package(s) according to the appropriate up‐
date instructions!
n After this is done, create an up-to-date recovery image.
n A technical info is published in the CS knowledge base (SKB0037721). This is a refer‐
ence table for all RuH packages that have been released for the RFU platform. To es‐
tablish whether a package applies to a particular system, contact your dispatcher/
USC/RSC.

1.5.18 Recovery image

n Prepare an up-to-date backup of the system partition according to the document
AX41-060.816.14, which is published on the CB-DOC.

© Siemens, 2015 XPR2-140.816.01.01.02 Page 49 of 55 Cios Select

01.16 SSME CS PLM
50 2 Local printer installation (option)

2.1 General information

 Perform the steps in this chapter only if the system is equipped with a local printer.

Local printer, PostScript printer

 These printer types are not approved for diagnostic purposes.

Notify the responsible personnel about this limitation.

Cios Select XPR2-140.816.01.01.02 Page 50 of 55 © Siemens, 2015

01.16 SSME CS PLM
 Local printer installation (option) 2 51

2.2 Reconfiguring the local Sony UP-971AD / 991AD /D898MD

printer (optional)

 The printer drivers for the Sony UP-971AD / 991AD /D898MD were already pre-installed
during SW installation.

Prerequisites
1. For the necessary test exposures, make sure the printer has paper or film.

Printer driver settings

1. Start the SSW.
2. Active the Windows Start Menu by pressing <Ctrl>and <Esc> simultaneously.
3. Click the Control Panel icon.
4. Click Control Panel Home on the control panel (top left).
5. Select View by: small icons from the drop-down menu in the top right corner (if
View by: small icons is not already displayed).
6. Click the Devices and Printers icon.
7. Delete all existing Sony UP-xxx printer devices. To do this, right-click each Sony UP-
xxx printer and select Remove Device.
8. Switch the system OFF and then back ON again.
9. Open the Control Panel and click the Devices and Printers icon again.
 A new printer device for the connected Sony UP-xxx printer will be present. (It
has been preset as the default printer.)
10. Right-click the Sony UP-xxx printer device.
- Select Printing Preferences for this printer.
- Under the Layout tab, select 3414x2560 for UP-971AD / 991AD or 960x1280 for
UP-D898MD as the paper size.
- Press OK.
11. Close the control panel and exit the SSW.

Printer settings in the user mode

1. Click the Settings icon on the TCP.
2. Click the Settings tab (in the top left corner of the live display).
3. Click the User Settings icon (wrench).
 The User Settings menu appears.
4. Select Image Display and Print Properties.
5. Select the Print Layout tab in the Image Display and Print Properties window.
6. In the Name drop-down box, type the printer name (for example, Sony UP-991AD).
7. For Type, select Paper.

© Siemens, 2015 XPR2-140.816.01.01.02 Page 51 of 55 Cios Select

01.16 SSME CS PLM
52 2 Local printer installation (option)

8. For the paper size, select the 8INx10IN format.

9. Select a 1x1 layout.
10. Save the settings with <Store> and <OK>.

Additional printer settings in the user mode (only with existing “DICOM Print” li‐
cense)

 The Sony printer can be set as the default printer under DICOM Properties.

1. In the User Settings menu, select DICOM Properties.

2. Click the Printing tab.
3. From the Target drop-down box, select Paper Printer.
4. From the Layout drop-down box, select the printer name previously given (for exam‐
ple, Sony UP-991AD).
5. Save the settings with <OK>.
6. Switch the system OFF and then back ON again.

Functional check of the printer

1. Click the Settings icon on the TCP.
2. Click the Service tab (in the top left corner of the live display).
3. Click the Check test images icon.
 The available test images appear on the live display.
4. Select a test image.
5. Click the Print button on the lower left side of the live monitor.
 The input dialog box for print settings is displayed on the live monitor.
6. Click the Print button in the input dialog box for print settings.
 The print job is started.

Cios Select XPR2-140.816.01.01.02 Page 52 of 55 © Siemens, 2015

01.16 SSME CS PLM
 Changes to previous Version 3 53

n.a.

© Siemens, 2015 XPR2-140.816.01.01.02 Page 53 of 55 Cios Select

01.16 SSME CS PLM
54 4 List of Hazard IDs

There are no Hazard IDs in this document.

Cios Select XPR2-140.816.01.01.02 Page 54 of 55 © Siemens, 2015

01.16 SSME CS PLM
All documents may only be used for
rendering services on Siemens
Healthcare Products. Any document
in electronic form may be printed
once. Copy and distribution of elec‐
tronic documents and hardcopies is
prohibited. Offenders will be liable
for damages. All other rights are re‐
served.

healthcare.siemens.com/services

Siemens Healthcare Headquarters

Siemens Healthcare GmbH
Henkestr. 127
91052 Erlangen
Germany
Telephone: +49 9131 84-0
siemens.com/healthcare

Print No.: XPR2-140.816.01.01.02 | Replaces: n.a.

Doc. Gen. Date: 01.16 | Language: English
© Siemens Healthcare GmbH, 2015

siemens.com/healthcare