Rendered PDF File Page 2 of 27 DOC0933241, Rev:1

GE Healthcare

1.5T Scanner Software V3.x Reinstallation Guide

Operating Documentation

DOC0933241
Rev 1.0
2011, General Electric Company,
All Rights Reserved.
Released
 1.5T Scanner Software V3.x Reinstallation Guide Rendered PDF File Page 3 of 27 DOC0933241, Rev:1

Revision History

Revision Date Changes

1.0 March, 2011 Initial conversion of ONI 2000-9308-020 to GE format

Released

2 of 25
 Rendered PDF File Page 4 of 27 DOC0933241, Rev:1
1.5T Scanner Software V3.x Reinstallation Guide Table of Contents

Table of Contents
Backing up Configuration Files ...............................11
Revision History .............................................................2 Backing up Magnet History file...............................11
Table of Contents ...........................................................3 Backing up System Protocols ..................................11
List of Figures .................................................................4 De-installing Webex ................................................12
1 Overview Starting Windows PE ..................................................12
Contents ........................................................................5 Preparing the Hard Disk: Partitioning ........................13
Related Materials ..........................................................5 Installing the Software ................................................14
Required Materials .......................................................5 Installing Silhouette Licenses .....................................15
Software Disks ...........................................................5 Initializing Windows and the Database ......................15
Network Configuration Information ..........................5 Exiting the Software Install Application ....................15
Navigation ....................................................................6 Restoring the Configurations ......................................16
Links ..........................................................................6 The Restore Config Button ......................................16
Bookmarks .................................................................6 Restoring the Configuration Files ............................16
Switching Between Documents .................................6 Restoring the Magnet History file............................16
Conventions ..................................................................6 Restoring the System Protocols ...............................16
Text Conventions .......................................................6 Configuring the Computer and Network Settings ......16
Terminology...............................................................7 Restarting the Computer ..........................................17
Safety Hazard Alerts ..................................................8 Setting the Date, Time, and Time Zone ...................18
Electrical Safety Symbols ..........................................8 Setting Up the Network Connections.......................19
Trademarks ...................................................................8 Network Setup .....................................................19
2 Installing the Software Computer Name Setup ........................................22
Chapter Contents ..........................................................9 Load Single Media Archive and Worklist ...............23
The Procedure: Overview .............................................9 Loading Operator Documentation ...........................23
Before Beginning .......................................................9 Install Webex Remote Access..................................24
Backing Up the System Configuration Files ..............10 Testing .......................................................................25
Create Ghost Image of the System Software ...........10 Changing the Date Format to European Mode ........25
Recording Network Configuration ..........................10 Index ..............................................................................26
Recording Current Printer ...................................10
Recording DICOM Transfer Destinations ..........11
Released

3 of 25
 Rendered PDF File Page 5 of 27 DOC0933241, Rev:1
1.5T Scanner Software V3.x Reinstallation Guide List of Figures

List of Figures
Adobe Reader Back Button . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Open the Control Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Options Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Printer Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Date/Time Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Boot Prompt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Date and Time Properties Window . . . . . . . . . . . . . . . . . . . 19
OrthOne Install Script Menu . . . . . . . . . . . . . . . . . . . . . . . . .13 Time Zone Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Erase Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Network and Internet Connections . . . . . . . . . . . . . . . . . . . . 20
Partitioning Complete Message . . . . . . . . . . . . . . . . . . . . . . .14 Network Connections Options . . . . . . . . . . . . . . . . . . . . . . . 20
Reformat Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 The Local Area Connection Status Window . . . . . . . . . . . . 21
Formatting Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Local Area Connection Properties . . . . . . . . . . . . . . . . . . . . 21
Copying Files Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Internet Protocol (TCP/IP) Properties . . . . . . . . . . . . . . . . . 22
Software Installed Message . . . . . . . . . . . . . . . . . . . . . . . . . .14 Performance and Maintenance Options . . . . . . . . . . . . . . . . 22
License Installed Message . . . . . . . . . . . . . . . . . . . . . . . . . . .15 System Properties/Computer Name Dialog . . . . . . . . . . . . . 22
Closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Computer Name Changes Dialog . . . . . . . . . . . . . . . . . . . . . 23
Restoreconfig . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Starting the Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Phone and Modem Options Window . . . . . . . . . . . . . . . . . . .17 eDocs CD Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
System Settings Change Window . . . . . . . . . . . . . . . . . . . . .17 WebEx configuration entries . . . . . . . . . . . . . . . . . . . . . . . . 24
Welcome to Windows Screen . . . . . . . . . . . . . . . . . . . . . . . .17 Date Mode Batch Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Logon To Windows Screen . . . . . . . . . . . . . . . . . . . . . . . . . .17
Released

4 of 25
 1.5T SCANNER SOFTWARE V3.X REINSTALLATION GUIDERendered PDF File Page 6 of 27 DOC0933241, Rev:1

1 Overview
This document is written for Service reinstallation of scanner software by trained Service representatives. Persons performing the
procedure should have a basic understanding of personal computers and familiarity with the installation of Windows software.
The guide describes the procedure for reinstalling the host computer operating system software and the EXTREME® Scanner V3.5x
software on the scanning system’s host computer. The procedures requires that peripheral devices such as the DVD- RAM drive,
the CD-RW drive, and the 3.5” floppy drive are already properly installed in the host computer, and that all of the software
installation disks are available.

Contents
The Reinstallation Guide contains the following chapters:
• Chapter 1, Overview, is this chapter. It lists the major sections of the Reinstallation Guide, and explains the text conventions
used.
• Chapter 2, Installing the Software, explains how to install the system software.

Related Materials
Information related to installing the 1.5T system is in the following documents:
• Scanner SW Release Notes, 5009-4300TPH
• Vendor-supplied manual, CEDARA Silhouette Service Manual, DOC0798902
• 1.5T Extremity Scanner Operator Manual, 5000-4700-001

Required Materials
Software Disks
To perform this reinstallation procedure, you must have the software disks listed below.
• INSTALLATION TOOL FOR ORTHONE Software CD, part no. 2009-4409-001
• Cedara Silhouette license file floppy disk (site’s license disk)
• 1.5T Software Installation disk, part no. 5009-4400-001
• Service Tools CD, 5000-9300-001
• System Recovery AB2000, 2000-9315-001

Network Configuration Information

Before performing this reinstallation procedure, you must obtain the network configuration data for the customer system. To
complete the reinstallation procedure, you must re-input the site’s IP address, Subnet mask and Gateway information. You can find
this information in the computer control panel. See Backing Up the System Configuration Files on page 11 for details on how to
find this information.
Released

5 of 26
 Rendered PDF File Page 7 of 27 DOC0933241, Rev:1
1.5T Scanner Software V3.x Reinstallation Guide

Navigation
Links
Blue text, as in the chapter references in the Contents section above, indicates a link to another section or document. Clicking the
blue text displays the linked section or document.
Though not displayed in blue, all page listings in the Table of Contents and in the Index are links. Clicking a listing in the Table of
Contents or the Index displays the listed page.

Bookmarks
The Bookmarks tab at the top left corner of the Acrobat screen provides a hierarchy of document headings that works like
Windows Explorer. Clicking a heading in the Bookmarks list opens the page that contains the heading. To open or close the
bookmarks display, click the Bookmarks tab. Closing the Bookmarks display provides a larger display area for the document.

Switching Between Documents

Figure 1-1 Adobe Reader Back Button

After following a link to another PDF document or to a location within the Software
Reinstallation Guide, use the back (left arrow) button at the bottom of the Adobe Reader
window to return to the original location.
After following a link to a non-PDF document, press Alt-Tab to return to this document.

Conventions
The conventions described below are used throughout the ORTHONE service documents.

Text Conventions
The following text conventions indicate on-screen features and controls, and emphasize important operations:
• References to on-screen text and controls are in a special font, to distinguish them from the normal flow of text.
Example: When Clone completed Successfully appears, remove the floppy and CD-ROM disks.
In the example, “Clone completed Successfully” is text in the computer display.
• When a reference to on-screen text includes an undefined variable, the variable is in italics, between brackets.
Example: No connection to Server <Orthone:[database number]>
In the example, “[database number]” refers to a value that is not specified. The rest of the example is the same as the display
text.
• In some procedures, the most significant words in a step are in bold type. If the words refer to an on-screen feature, they are in
the special font in bold.
Example: On the Start Copying Files window, click Next>.
In the example, the N in “Next” is underlined because it is underlined in the display.
Released

6 of 26
 Rendered PDF File Page 8 of 27 DOC0933241, Rev:1
1.5T Scanner Software V3.x Reinstallation Guide

Terminology
The following terms have the meanings listed here:
• “Press” means to press a key or switch on a keyboard or other input device. (It does not refer to operating on-screen controls.),
The name of the control is in the regular font.
Example: Press Enter.
• “Click” means to place the mouse cursor on an item on the screen, and press the left mouse button.
Example: Click Finish.
Clicking causes the computer to perform an operation, such as opening or closing a window, saving data, or executing a task.
• “Double-click” means to place the mouse cursor on an item on the screen, and press the left mouse button twice.
Example: Double-click the Network icon.
• “Right-click” means to place the mouse cursor on an item on the screen, and press the right mouse button.
Example: Right-click the file name and select Properties from the drop-down menu.
• “Select” means to pick an option or file name from a list, by clicking it or rolling the mouse cursor over it.
Example: From the Edit menu, select Copy.
Selecting usually has no immediate result, and requires a subsequent click operation to implement the selection.
Released

7 of 26
 Rendered PDF File Page 9 of 27 DOC0933241, Rev:1
1.5T Scanner Software V3.x Reinstallation Guide

Safety Hazard Alerts

There are three hazard classifications used in this document:
Alert Circumstance for Use
Danger indicates an imminently hazardous situation, that, if
not avoided, will result in death or serious injury. Danger is
limited to extreme situations.

Warning indicates a potentially hazardous situation, that, if not

avoided, could result in death or serious injury.

Caution indicates a potentially hazardous situation, that, if not

avoided, may result in moderate to minor injury.

Electrical Safety Symbols

The MR system is a Class 1, type B applied part, rated for continuous operation. This device classification refers to the
level of protection provided against electrical shock to the parts are in contact with the patient.

The symbol shown to the left, where displayed, indicates that there are dangerous voltages accessible beyond that point.
Access may pose a safety risk and should only be done by qualified service personnel.

The symbol shown to the left indicates a safety warning and that accompanying documents should be consulted.

The symbol shown to the left indicates that this terminal is used for potential equalization.

Notes contain important information that can help you perform service operations. A note can describe a
special condition you may encounter, can describe actions that simplify your work, or can alert you to other
actions that create unnecessary work.

Trademarks
Windows, Microsoft, and the Windows logo graphic are registered trademarks of Microsoft Corporation.
Silhouette is a registered trademark of the Cedara Software Corporation.
All other brand names and product names used in this document are trademarks, registered trademarks, or trade names of their
respective holders.
Released

8 of 26
 1.5T Scanner Software V3.x Reinstallation Guide Rendered PDF File Page 10 of 27 DOC0933241, Rev:1

2 Installing the Software

Chapter Contents
This section includes the following topics:
• Backing Up the System Configuration Files on page 10
• Starting Windows PE on page 12
• Preparing the Hard Disk: Partitioning on page 13
• Installing the Software on page 14
• Installing Silhouette Licenses on page 15
• Initializing Windows and the Database on page 15
• Exiting the Software Install Application on page 15
• Restoring the Configurations on page 16
• Configuring the Computer and Network Settings on page 16
• Testing on page 25.

The Procedure: Overview

In this procedure, a preinstallation boot CD containing Microsoft® Windows® Preinstallation Environment (Windows PE) is used
to boot the system and display a menu, which is then used to perform the software installation. The installer selects functions from
the menu to:
• Prepare the hard disk by partitioning and formatting (used only if the installation requires a new hard disk).
• Install the Microsoft Windows XP Embedded Operating system, and the 1.5T scanner software.
• Install the site license.
• Display information about the current status of the hard disk, if desired.
• Open a command window, which allows you to input typed commands if desired.
As you perform the installation, you may notice slight discrepancies from the information in these procedures, depending on the
exact configuration of the system on which you are installing the software. As a general rule, do not deviate from on-screen
instructions during the setup and installation procedures.

Except as noted, perform all the steps in each procedure in the order shown. Deviating from the
prescribed order or omitting a step can cause the installation to fail. Installation failure may not be
evident until long after a mistake is made, so read and perform each step carefully.

At the end of the installation, the following software is installed on the host computer:
• The Windows® XP operating system and all required third-party driver software
• Silhouette® imaging software from the Cedara Software Corporation
• EXTREME 3.5x Scanner software
• Backed-up configuration files and protocols from the customer’s previous system
• The site license

Before Beginning
Before you begin the reinstallation:
• Check with the customer to make sure that the facility has archived all desired studies (See Operator’s Guide, Chapter 10).
• Review the software Release Notes (5009-4300TPH) for updates and the latest information on software installation.
Released

9 of 25
 Rendered PDF File Page 11 of 27 DOC0933241, Rev:1
1.5T Scanner Software V3.x Reinstallation Guide

Backing Up the System Configuration Files

Prior to reinstalling software, it is extremely important that you perform the following actions.
• Create Ghost Image (only necessary when reloading software on to the same hard disk)
• Recording Network Configuration
• Recording current printer and DICOM transfer destinations
• Backing up Configuration Files (saved using the BackUpconfig.bat file)
• Backing up Magnet History file
• Backing up System protocols
• De-install Webex (so that the same name can be used when re-installing Webex after loading the new software)
• Locate the Silhouette license floppy or, when reloading to the same disk, copy the license folder to the D: drive

Create Ghost Image of the System Software

Create a backup copy of the entire contents of the C: drive (all the system software, configuration information and the image
database). This copy can be used to restore the system software to a known good state. A clinical user should be able to perform
this recovery process with telephone support from a service engineer.
1. Before starting, make sure the system is configured correctly and the database is empty. Remember that the customer will
restore exactly what you are saving away, and any problems may render them unable to scan.
2. Insert the System Recovery AB2000 CD, part number 2000-9315-001, in the CD drive.
3. Reboot the computer.
4. When you see a message asking you to type Ctrl-C to exit or any other key to continue, type Ctrl-C. Answer Y to the question
if you want to terminate the batch job.
5. At the A: prompt, type backupc and press Enter.
6. Wait for the backup to finish and the A: prompt to reappear.
7. Remove the CD from the CD drive and type Ctrl-Alt-Del or press the Reset switch on the computer.
The ghost image is stored on the D: drive.

Recording Network Configuration

See Setting Up the Network Connections on page 19 for details on how to find the following information.
Record the following network information:
• IP Address
• Subnet mask
• Default Gateway
• DNS server address if used
• Computer Name
• Workgroup Name if used
• Firewall setting if used
• Recording current printer and DICOM transfer destinations
Figure 2-1 Options Button

Recording Current Printer

1. Go to the Patient List.
2. Select an exam.
3. Select View.
4. From the image viewing page, select the Options button. See Figure 2-1.
5. Record the currently selected printer. (example DICOM Codonics NP1600M) See Figure 2-2.
Released

10 of 25
 Rendered PDF File Page 12 of 27 DOC0933241, Rev:1
1.5T Scanner Software V3.x Reinstallation Guide

Figure 2-2 Printer Select

Recording DICOM Transfer Destinations

1. Go to the Patient List.
2. Select Archive in the upper right hand corner.
3. Select Transfer.
4. Record the Source and Destination nodes.

Backing up Configuration Files

The backup will be done through the command window. The BackUpconfig.bat file is loaded by the service
tools CD. If the file is not available, re-load the service software.

1. Log on as Administrator. Use the password smradmin.

2. Go to the Start menu and select Run…
3. In the Run popup window, type cmd
4. When the command window opens, type in net stop css
5. Change the directory to c:\ and either delete the error log or rename the error log.
6. Change the directory to: C:\Program Files\ONI\OrthOne\ServiceTools
The backupconfig file will by default save the configuration files to the c:\BackupTemp directory. To select
another drive, input the drive letter.

7. Type in backupconfig a to save the files onto a floppy disk. You may also want to make a copy of the BackupTemp folder on
the D: Drive. (type in backupconfig d)
8. Label the disk with the site name and the date, and leave the floppy disk with the site software.

Backing up Magnet History file

Copy the shim history file (located at C:\Program Files\ONI\OrthOne\ServiceTools\Magnet Data) onto another floppy disk, label the disk,
and leave it with the site software. The file format is: Magnet_[serial number].dat.

Backing up System Protocols

1. Reboot the system.
2. Log on as sdc. Use the password adw2.0.
3. Go to the Protocol editor screen in clinical mode, click Backup to call up the protocol/sequence backup screen.
4. Select All from the Select Owner drop-down list.
5. Save the protocols to a floppy disk (or to the D: drive if reloading onto the same hard disk), enter the location and name of the
file to be created in the File field. Select Backup.
Released

11 of 25
 Rendered PDF File Page 13 of 27 DOC0933241, Rev:1
1.5T Scanner Software V3.x Reinstallation Guide

6. Click OK to dismiss the dialog that indicates the successful saving of protocols and sequences.
7. Click Done to return to the Protocol Editor.

De-installing Webex
1. Record the Webex computer name (if you do not have Webex, contact the online center to obtain the computer name).
2. Go to the Start -> All Programs -> Webex Remote Access.
3. Select Uninstall Remote Access Agent.

Starting Windows PE
This procedure requires two CDs: the system software installation CD, and the Windows preinstallation boot CD.
1. Insert the 1.5T Software Installation disk, part no. 5009-4400-001, in the the DVD-RAM drive (lower drive).
2. Insert the Windows preinstallation boot CD (Installation Tool for ORTHONE Software, part no. 2009-4409-001) into the CD
drive.
3. Reboot the computer.
Figure 2-3 Boot Prompt

4. When you see the prompt Press any key to boot from CD (Figure 2-3), press
any key on the keyboard.
Released

12 of 25
 Rendered PDF File Page 14 of 27 DOC0933241, Rev:1
1.5T Scanner Software V3.x Reinstallation Guide

Watch carefully for this prompt. If you do not press Enter in the few seconds provided, the system will boot
without installing the OrthOne Install Script menu. If this occurs, you will need to start again from Step 3.

When the system finishes booting up (two-three minutes), the OrthOne Install Script window opens. Use the buttons on the left
side of this menu to perform most of the procedures described in this chapter.
Figure 2-4 ORTHONE Install Script Menu

Do not use

All the buttons shown in the menu are referred to in this chapter except the Get Disk Info button. The Get Disk
Info button displays detailed information about the status of the hard disk, including partition, drive letter, and
format information and can be useful for expert use during troubleshooting.

Preparing the Hard Disk: Partitioning

These instructions explain how to partition new hard disks for software installation.

Do NOT partition the hard disk unless this is a fresh installation of the software on a new hard disk.
Partitioning the disk erases ALL data on all partitions on the disk. This procedure is NOT required for
software upgrades or reinstallation of the SW on a functional disk. If you are performing a software
upgrade or a reinstallation on a previously used disk, skip this section, and go to the next section,
Installing the Software.

1. Prior to installation, backup the configuration files to a floppy disk as described above, or use an alternative backup method and
restore the files manually after the software is installed.
2. On the OrthOne Install Script window (Figure 2-4), click Prepare Disk.
Released

13 of 25
 Rendered PDF File Page 15 of 27 DOC0933241, Rev:1
1.5T Scanner Software V3.x Reinstallation Guide

Figure 2-5 Erase Warning

A message box opens, warning that all files will be erased (Figure 2-5).
3. Click Yes to continue with partitioning.
The Install script begins to partition the drive, and a Command window opens,
displaying partitioning messages.

Figure 2-6 Partitioning Complete Message

When partitioning is complete, a message box opens, indicating that partitioning is

complete (Figure 2-6).
4. Click OK.

Installing the Software

1. On the OrthOne Install Script window (Figure 2-4 on page 13), click Clean Install.
Figure 2-7 Reformat Warning

A message box opens, warning that the C:\ drive will be erased if you continue
installation.
2. Click Yes to continue with reformatting and installation.

Figure 2-8 Formatting Messages

The Install script begins to reformat the C:\ drive, and a Command
window opens briefly, displaying formatting messages.

Figure 2-9 Copying Files Messages

s

Another Command window opens, displaying the message: Copying

files. . .

The software installation takes approximately 20 minutes. During installation, no on-screen update messages
appear. To track progress, you can observe the HD1 and HD2 lights on the front of the computer. These lights
flash when there is activity on the respective drives.

Figure 2-10 Software Installed Message

When the software installation is complete, a message box opens, indicating that the
software is successfully installed.
3. Click OK.
Released

14 of 25
 Rendered PDF File Page 16 of 27 DOC0933241, Rev:1
1.5T Scanner Software V3.x Reinstallation Guide

Installing Silhouette Licenses

For this procedure you will need the Silhouette license floppy disk from the site’s software wallet.
1. Insert the Silhouette license floppy disk into the host computer’s floppy disk drive.
2. On the OrthOne Install Script window (Figure 2-4 on page 13), click License.
The Install script installs the Silhouette licenses.
Figure 2-11 License Installed Message

3. When a message box opens, indicating that the license files are
successfully copied, click OK.
4. Remove the Silhouette license floppy disk from the drive and return it to
the site software wallet.

Initializing Windows and the Database

1. Click Command on the OrthOne Install Script menu (Figure 2-4 on page 13).
A command window opens.
2. Type c:\FinalSetup at the command prompt in the command window and press Enter.
The final setup process will start by displaying a banner and version number. Additional lines of text will appear and may scroll
up the screen as the process progresses.
When the process is complete, a line of text starting with [Success], [Errors] or [Skipped] will be displayed.
[Success]- The final setup procedure completed without errors.
[Errors] - Problems were reported during one or more steps of the final setup procedure. Write down all errors displayed in the
command window and contact Service Support.
[Skipped]- The database was already initialized.
3. Type exit at the command prompt and press Enter.
The command window closes.

Exiting the Software Install Application

1. Close the application by clicking Close on the OrthOne Install Script menu.
A Command window opens.
Figure 2-12 Closing

2. Type exit at the command window prompt and press Enter.

The system shuts down and restarts, coming up at the Welcome to Windows
screen (Figure 2-16).
3. Ignore the Hit any key to boot from CD message , and let the system
boot from the hard disk.
4. Remove the disks from the CD and DVD RAM drives.

It can take up to five minutes for the system to execute this step.
Released

15 of 25
 Rendered PDF File Page 17 of 27 DOC0933241, Rev:1
1.5T Scanner Software V3.x Reinstallation Guide

Restoring the Configurations

The Restore Config Button
Do not use the Restore Config button. To backup the configuration files, use the Restoreconfig.bat file from the
Service Tools CD, part number 5000-9300-001. If service tools are already installed on the system, the bat
file is located at: C:\Program Files\ONI\OrthOne\ServiceTools.
This procedure restores the configuration backup files you made in Backing Up the System Configuration Files on page 10.

Restoring the Configuration Files

The restore will be done through the command window. The Restoreconfig.bat file is loaded by the service
tools CD. If the file is not available, re-load the service software.

1. Log on as Administrator. Use the password smradmin.

2. Go to the Start menu and select Run…
3. In the Run popup window, type cmd
4. When the command window opens, type in net stop css
5. Change the directory to: C:\Program Files\ONI\OrthOne\ServiceTools
6. Type in restoreconfig a (or restoreconfig d if you backed up to the D: drive) to restore the files from the backup config floppy
disk.
7. Respond to each overwrite question by typing a, and respond to the worklist config file restore by typing d (see Figure 2-13).
Figure 2-13 Restoreconfig

Restoring the Magnet History file

Copy the shim history file from the shim history floppy disk to the
following location:
C:\Program Files\ONI\OrthOne\ServiceTools\Magnet Data

Restoring the System Protocols

1. Reboot the system.
2. Log on as sdc. Use the password adw2.0.
3. Go to the Protocol editor screen, click Backup to call up the
protocol/sequence backup screen.
4. Browse to select the backup file on the floppy disk (drive A)
5. Click Restore.
6. Click OK to dismiss the dialog indicating that protocols and sequences
are restored.
7. Click Done to return to the Protocol Editor.
8. Remove the floppy disk from the floppy drive.

Configuring the Computer and Network Settings

To finish the reinstallation procedure, you must set the time and time zone and input the IP address, Subnet mask, and Gateway
information for the customer site. You should have noted this information as part of Recording Network Configuration on page 10.
Before continuing with this procedure, review the following operating notes:
Released

16 of 25
 Rendered PDF File Page 18 of 27 DOC0933241, Rev:1
1.5T Scanner Software V3.x Reinstallation Guide

Figure 2-14 Phone and Modem Options Window

While performing these procedures, if a Phone and Modem Options window opens, warning that a control panel
cannot be opened, click OK in the window. This warning does not indicate a problem for this installation.

Figure 2-15 System Settings Change Window

While performing these procedures, when a System Settings Change window opens, click No in answer to the
question Do you want to restart your computer now? Do not restart the computer unless directed in these
instructions.

Restarting the Computer

Figure 2-16 Welcome to Windows Screen

If you have followed the instructions in order in on page 15, your system will
be displaying the Welcome to Windows screen.

1. Press Ctrl-Alt-Delete.

Figure 2-17 Logon To Windows Screen

2. Log on as Administrator, using the password smradmin.

The User name: field is not case sensitive, but the

Password: field is case sensitive.

3. Click OK to log in.

4. Click Control Panel (Figure 2-18) from the Windows Start window.
Released

17 of 25
 Rendered PDF File Page 19 of 27 DOC0933241, Rev:1
1.5T Scanner Software V3.x Reinstallation Guide

Figure 2-18 Open the Control Panel

5. The Control Panel window (Figure 2-19) opens

Figure 2-19 Control Panel

Setting the Date, Time, and Time Zone

Since this is a new operating system, you must set the date,
time, and time zone.

Figure 2-20 Date/Time Control Panel

1. On the Control Panel, click Date, Time, Language, and Regional Options
The Date, Time, Language and Regional Options window opens (Figure 2-20).
2. Click Date and Time.
The Date and Time Properties window opens (Figure 2-21).
3. Click on the arrow to the right of the month field to select the month.
4. Click the up or down arrow to the right of the year field to select the year.
5. Click the day of the month on the calendar.
6. Click the up or down arrow to the right of the time field to select the correct hour.
7. Type in the correct minutes and seconds.
Released

18 of 25
 Rendered PDF File Page 20 of 27 DOC0933241, Rev:1
1.5T Scanner Software V3.x Reinstallation Guide

Figure 2-21 Date and Time Properties Window

8. Click the Time Zone tab.

The Date and Time Properties window displays a world map (Figure 2-
22).

Figure 2-22 Time Zone Tab

9. Click the arrow at the right of the time zone field, and select the time
zone of the customer site from the menu that appears.
10. Check or uncheck the Automatically adjust clock for daylight saving changes,
as required for this site.
11. Click OK to close the Date and Time Properties window.

GE configures systems to use the “American” date format of month/day/year (mm/dd/yyyy). If the system is
installed in a site using the “European” format (dd/mm/yyyy), use the procedure described in Changing the
Date Format to European Mode on page 25.

Setting Up the Network Connections

Network Setup
1. Click the back arrow ( ) at the top left of the Date, Time, Language, and Regional Options window to return to the
Windows Control Panel. (See Figure 2-19 on page 18.)
2. From the Control Panel, click Network and Internet Connections.
The Network and Internet Connections options window displays (Figure 2-23).
Released

19 of 25
 Rendered PDF File Page 21 of 27 DOC0933241, Rev:1
1.5T Scanner Software V3.x Reinstallation Guide

Figure 2-23 Network and Internet Connections

3. Click Network Connections at the bottom of the window.

The Network Connections Options window opens (Figure 2-24).

Figure 2-24 Network Connections Options

4. Double-click Local Area Connection.

The Local Area Connection Status window opens (Figure 2-25).

If the customer’s data line has been installed, the Local Area
Connection will say “Enabled,” as shown in Figure 2-24. If the data line has not yet been installed, the Local
Area Connection will be marked with a red “X” and the words “Network cable unplugged”.
Released

20 of 25
 Rendered PDF File Page 22 of 27 DOC0933241, Rev:1
1.5T Scanner Software V3.x Reinstallation Guide

Figure 2-25 The Local Area Connection Status Window

5. Click the Properties button at the bottom of the Local Area Connection
Status window.
The Local Area Connection Properties window opens (Figure 2-26).

If the Local Area Connection has not been installed, the Local Area Connection Status window does not
display. In this case, skip to step 6 to set up the connection information.

6. Highlight Internet Protocol (TCP/IP).

Figure 2-26 Local Area Connection Properties

7. Click the Properties button.

The Internet Protocol (TCP/IP) Properties window opens (Figure 2-27).
Released

21 of 25
 Rendered PDF File Page 23 of 27 DOC0933241, Rev:1
1.5T Scanner Software V3.x Reinstallation Guide

Figure 2-27 Internet Protocol (TCP/IP) Properties

8. Choose the Use the Following IP Address option.

9. Type in the assigned IP address, Subnet mask, and Default Gateway numbers
for this site.
10. Click OK, Close, and Close respectively to close the currently opened windows.

Computer Name Setup

1. Click the back arrow ( ) at the top left of the Network Connections and
Network and Internet Connections windows to return to the Windows Control
Panel. (See Figure 2-19 on page 18.)

2. On the Control Panel, click Performance and Maintenance.

The Performance and Maintenance options window opens (Figure 2-28).
Figure 2-28 Performance and Maintenance Options

3. From the Performance and Maintenance options window, click System at the
bottom of the window.
The System Properties panel opens.
4. Select the Computer Name tab.
The Computer Name dialog opens (Figure 2-29).
5. If desired, type a description in the Computer description entry field.

Figure 2-29 System Properties/Computer Name Dialog

6. Click the Change... button.

The Computer Name Changes dialog opens (Figure 2-30).

7. On the Computer Name Changes dialog, type the computer name into the
Computer Name entry field.
Released

22 of 25
 Rendered PDF File Page 24 of 27 DOC0933241, Rev:1
1.5T Scanner Software V3.x Reinstallation Guide

Figure 2-30 Computer Name Changes Dialog

8. Click the domain or workgroup button in the Member of area to select the
appropriate category for this site.
9. Type in the name of the domain or workgroup for this site.
10. Click OK.
11. Click OK on the workgroup and computer name change messages which open.
12. Click OK to close the System Properties window.
A System Settings Change message appears, asking Do you want to restart your
computer now?
13. Click Yes to restart the computer.

Figure 2-31 Starting the Application

14. At the Log On to Windows screen (Figure 2-31), type in the following login and
Password (for your specific version):
User name: sdc
Password: adw2.0

Load Single Media Archive and Worklist

1. Use the document DOC0797550 SMA SW Installation Instructions.doc from the
Service CD to load the Single Media Archive utility. After you have loaded it, drag and drop the SMA icon from the Start --> All
Programs menu to the Start menu.
2. Use the DOC0797552 DICOM Worklist Installation Instructions.doc from the Service CD to load the DICOM Worklist utility.
After you have loaded it, drag and drop the Worklist icon from the Start --> All Programs menu to the Start menu.

Loading Operator Documentation

1. Log in to the system using the sdc account.
2. Insert the MSK Extreme 1.5T Operator User Guide CD, part number 5000-4700-001, into the CD drive.
3. If the CD menu does not come up automatically, run setup.bat from the CD.
4. On the CD menu, select Install Adobe Reader® version 9.0 from this CD and follow the instructions to load the PDF reader.
5. On the CD menu, select Install User Guides to Your Computer.
Figure 2-32: eDocs CD Menu
Released

23 of 25
 Rendered PDF File Page 25 of 27 DOC0933241, Rev:1
1.5T Scanner Software V3.x Reinstallation Guide

Install Webex Remote Access

WebEx Remote Access allows for broadband access to the scanner from a remote location. This can be used for service and
applications support. WebEx access to the scanner is not available for international service organizations, but distributors are
encouraged to install the software, when possible, in order to enable the best possible support from GE Medical Systems, should
that be called for.
To install and enable the WebEx Remote Access agent included with the system software:
1. Make sure the scanner is connected to the internet (e.g. by running iexplore.exe and going to a known site).
2. Execute the file c:\Program Files\ONI\OrthOne\WebEx\atsmt.msi
3. Follow the prompts to move through the first screens and accept the license agreement. Don’t change any of the defaults.
Occasional progress indicators will pop up and go away as the program installs.
4. Continue accepting the defaults and moving through the screens until you see the screen in Figure 2-33.
Figure 2-33: WebEx configuration entries

5. Type in the site acronym in the Computer name field and the string
ONIsupport.webex.com/ONIsupport in the Website URL field.

The computer name here is completely independent of the host

name used by Windows XP.

6. Continue accepting defaults to complete the software setup.

The last screen asks if you want to reboot the computer immediately. For this application, a reboot is necessary to complete the
software installation.
The software is now installed. To ensure that the system is working properly, test operation as described in Testing below.
Released

24 of 25
 Rendered PDF File Page 26 of 27 DOC0933241, Rev:1
1.5T Scanner Software V3.x Reinstallation Guide

Testing
After the software installation and configuration restoration are complete, test the archiving, DICOM transfer, and printing
functions of the system.

Consult the Operator’s Guide for detailed information on performing the functions described in this section.
Printing is discussed in Chapter 9; archiving, retrieving, and transferring studies are covered in Chapter 10.

1. Collect a series of images and use the archive function to archive them to a disk in the DVD-RAM drive.
2. If applicable, restore the default printer recorded earlier.
3. Restore the DICOM transfer destinations recorded earlier.
4. Verify that images can be transferred successfully to a remote site, using DICOM transfer.
5. Send an image to the designated printer to verify proper printer communication, if applicable.
6. Perform a DQA scan to insure proper system operation.
7. Test Webex operation.
8. After confirming that all functions are operational, perform a ghost image. Rename any previously saved ghost images.

Changing the Date Format to European Mode

GE configures systems to use the “American” date format of month/day/year (mm/dd/yyyy). If the system is installed in a site
using the “European” format (dd/mm/yyyy), you must change the format.
1. Use Windows Explorer to navigate to the SERVICE TOOLS directory on the Service CD.
(3.5.x\SERVICE TOOLS)
Figure 2-34 Date Mode Batch Files

2. Double-click Set European Date Format.bat to set the date format to

international mode. To see the changes, you must log out and log back in.

To turn international date mode off, Double-click Set American Date Format.bat.
Released

25 of 25
 Rendered PDF File Page 27 of 27 DOC0933241, Rev:1
1.5T Scanner Software V3.x Reinstallation Guide

Index
A D Network connections Switching between
Archiving studies, 9 Date setting, 19 documents, 6
setting, 18 Network settings, 16 System Settings Change
B window, 17
Date format O
Bookmarks, 6 European, 19, 25 Overview, 5 T
C E installation, 9 TCP/IP
CDs required, 12 European date format, 19, manual, 5 selecting, 21
Computer 20 P Testing, 25
restarting, 17 setting, 20 Time
Computer and network Partitioning hard disk, 13
setting, 18
settings I R Time Zone
configuring, 16 Install Script menu, 13 Required materials setting, 18
Computer name setup, 22 Installation software disks, 5 Trademarks, 8
Computer settings, 16 Software, 14 Restarting the computer, 17 W
Configurations L Restoring configurations, 16
restoring, 16 Windows PE
Links, 6 S installing, 12
Contents
Overview, 5 N Silhouette licenses
Conventions, 6 Navigation, 6 installing, 15
Conventions used Network configuration Software disks required, 5
terminology, 7 information required, 5 Software installation, 14
text, 6 Software installed, 9
Released

26 of 26