website:http://biz.LGservice.

com
e-mail:http://www.LGEservice.com/techsup.html

PLASMA TV
SERVICE MANUAL
CHASSIS : MF-056A

MODEL : 42PX4R
42PX4R-ZA

CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

TV/AV MENU OK VOL PR

Downloaded from www.Manualslib.com manuals search engine

 CONTENTS

SAFETY PRECAUTIONS ....................................................................................3

DESCRIPTION OF CONTROLS ..........................................................................4

SPECIFICATIONS ................................................................................................9

ADJUSTMENT INSTRUCTIONS .......................................................................11

TROUBLE SHOOTING GUIDE ..........................................................................15

BLOCK DIAGRAM .............................................................................................24

EXPLODED VIEW ..............................................................................................26

EXPLODED VIEW PARTS LIST ........................................................................27

REPLACEMENT PARTS LIST...........................................................................28

SCHEMATIC DIAGRAM.........................................................................................

PRINTED CIRCUIT BOARD ..................................................................................

-2 -

Downloaded from www.Manualslib.com manuals search engine

 SAFETY PRECAUTIONS

IMPORTANT SAFETY NOTICE

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in
the Schematic Diagram and Replacement Parts List.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to
prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.

General Guidance Leakage Current Hot Check (See below Figure)

Plug the AC cord directly into the AC outlet.
An isolation Transformer should always be used during Do not use a line Isolation Transformer during this check.
the servicing of a receiver whose chassis is not isolated from Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
the AC power line. Use a transformer of adequate power rating between a known good earth ground (Water Pipe, Conduit, etc.)
as this protects the technician from accidents resulting in and the exposed metallic parts.
personal injury from electrical shocks. Measure the AC voltage across the resistor using AC
voltmeter with 1000 ohms/volt or more sensitivity.
It will also protect the receiver and it's components from being Reverse plug the AC cord into the AC outlet and repeat AC
damaged by accidental shorts of the circuitry that may be voltage measurements for each exposed metallic part. Any
inadvertently introduced during the service operation. voltage measured must not exceed 0.75 volt RMS which is
corresponds to 0.5mA.
If any fuse (or Fusible Resistor) in this monitor is blown, replace In case any measurement is out of the limits specified, there is
it with the specified. possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.
When replacing a high wattage resistor (Oxide Metal Film
Resistor, over 1W), keep the resistor 10mm away from PCB.

Keep wires away from high voltage or high temperature parts. Leakage Current Hot Check circuit

Due to high vacuum and large surface area of picture tube,

AC Volt-meter
extreme care should be used in handling the Picture Tube.
Do not lift the Picture tube by it's Neck.

Good Earth Ground

such as WATER PIPE,
Leakage Current Cold Check(Antenna Cold Check) To Instrument’s CONDUIT etc.
With the instrument AC plug removed from AC source, 0.15uF
exposed
connect an electrical jumper across the two AC plug prongs. METALLIC PARTS
Place the AC switch in the on position, connect one lead of
ohm-meter to the AC plug prongs tied together and touch other
ohm-meter lead in turn to each exposed metallic parts such as 1.5 Kohm/10W
antenna terminals, phone jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1MΩ and 5.2MΩ.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.

-3 -

Downloaded from www.Manualslib.com manuals search engine

 DESCRIPTION OF CONTROLS

Remote Control Key Functions

- When using the remote control aim it at the remote control sensor of the set.
- There's maybe a defect in consecutive operation of remote control in specified brightness according to this set feature.

TV/AV POWER
Selects the TV, AV, Component, RGB or switches the set on from standby or off to
HDMI modes. TV/AV MULTIMEDIA standby.
switches the set on from standby. POWER
MULTIMEDIA
MODE DVD
VCR
Selects the Component, RGB or HDMI
TV
Selects another device. MODE
modes.
CABLE
AUDI
O STB switches the set on from standby.
ZOOM - / ZOOM +
ZOOM - ZOOM +
Enlarges or reduces the main picture size. PIP
MU
TE MUTE
SLEEP LIST Switches the sound on or off.
SLEEP TEX
T/
* I/II

Sets the sleep timer. I/II

U
ARC
EXIT
Selects the language during dual lan-
MEN
guage broadcast.
MENU Selects the sound output.
Displays on screen menus one by one.
Exits the current menu. LIST
Memorizes menu changes. OK Displays the programme table.

PIP EXIT
Switches the sub picture on or off. Clears all on-screen displays and returns
Selects PIP or DW modes. PIP
to TV viewing from any menu.
PR UT
INP
PIP PR + /- -
PIP PR + SWAP
PIP

Selects a programme for the sub picture.

SWAP ARC
Alternates between main and sub picture. Changes the picture format.
VOL SSM PSM PR
PIP INPUT
Selects the input mode for the sub picture. OK
SIZE accepts your selection or displays the cur-
Adjusts the sub picture size. rent mode.
POSITION D / E or F / G
Moves the sub picture to D / E or F / G Adjusts menu settings.
direction. Selects menu item.

SSM VOL +/- (Volume Up/Down)

To select the sound appropriate to your FAVOURITE Q.VIEW Increases/decreases sound level.
viewing programme character. PR +/- (Programme Up/Down)
SIZE POSITION INDEX HOLD
Selects a programme.
NUMBER buttons
TIME REVEAL MIX MODE

? M PSM
FAVOURITE Adjusts the factory preset picture accord-
selects a favorite programme. ing to the room.

Q.VIEW
TEXT/
These buttons are used for teletext. * Returns to the previously viewed pro-
gramme.
For further details, see the ‘Teletext’ section.
Note : In teletext mode, the PIP PR +/-,
SWAP and PIP INPUT buttons are used for VCR BUTTONS
teletext function. Controls a LG video cassette recorder.

-4 -

Downloaded from www.Manualslib.com manuals search engine

 Location and Function of Controls

<Front Panel Controls>

TV/AV MENU OK VOL PR

8

TV/AV MENU OK VOL PR

2 1 3 4 5 6

1. Power Button 6. D / E (Programme Up/Down)

Switches the set on from standby or off to standby. Selects a programme or a menu item.
Switches the set on from standby.
2. Remote Control Sensor
F / G (Volume Up/Down)
3. TV/AV Button Adjusts the volume.
Selects the TV, AV, Component, RGB or HDMI modes. Adjusts menu settings.
Switches the set on from standby.
7. Power Indicator
4. MENU Illuminates red in standby mode, Illuminates green when the
Displays on screen menus one by one. set is turned on
Exits the current menu.
8. Intelligent Eye
Memorizes menu changes.
Adjusts picture according to the surrounding conditions.
5. OK
Accepts your selection or displays the current mode.

-5 -

Downloaded from www.Manualslib.com manuals search engine

 Location and Function of Controls
- Shown is a simplified representation of the set.
- Here shown may be somewhat different from your set.
- This manual explains the features available on the 42PX4RV series / RT-42PX40 series.

<Back Panel>

AV5
S-VIDEO

VIDEO
9

R AUDIO L/MONO
VIDEO AUDIO
AV1 AC INPUT
L R
HDMI/ COMPONENT AUDIO Antenna
DVI(VIDEO) AUDIO INPUT RGB INPUT
L R

VARIABLE
VARIABLE AV2
AUDIO OUT
REMOTE RS-232C INPUT
CONTROL (CONTROL/SERVICE) AV4
AV3
L R
(MONO)
S-VIDEO VIDEO
AUDIO

1 2 3 4 5 6 7 8

1. HDMI(DVI VIDEO) / AUDIO INPUT / RGB INPUT 5. VARIABLE AUDIO OUTPUT

Connect the monitor output socket of the PERSONAL COM-
PUTER, DVD or STB to this socket. 6. EURO SCART SOCKET
Note: If you want to use RGB/DVI audio, we strongly recom- Connect the euro scart socket of the VCR to these sockets.
mend that you use the cable that has a core, or the EMI Filter Note: If you want to use the EURO scart cable, you have to
core along with separate cable. use the signal shielded Euro scart cable.

2. CONTROL LOCK / REMOTE CONTROL 7. ANTENNA INPUT

3. RS-232C INPUT(CONTROL/SERVICE) PORT 8. POWER CORD SOCKET

Connect to the RS-232C port on a PC. This set operates on an AC power. The voltage is indicated on
the Specifications page. Never attempt to operate the set on
4. COMPONENT INPUT DC power.
Connect DVD video outputs to Y, PB, PR of COMPONENT
INPUT and audio outputs to Audio sockets of AUDIO INPUT. 9. AUDIO/VIDEO INPUT (AV5)
S-VIDEO/AUDIO IN SOCKETS
AUDIO/VIDEO IN SOCKETS (AV4)
Connect the audio/video out sockets of external equipment to
these sockets.
S-VIDEO/AUDIO IN SOCKETS
Connect the S-VIDEO out socket of an VCR to the S-VIDEO
socket.
Connect the audio out sockets of the VCR to the audio sock-
ets as in AV4.

-6 -

Downloaded from www.Manualslib.com manuals search engine

 Displayable Monitor Specification
RGB / HDMI mode

Resolution Horizontal Vertical

Frequency(KHz) Frequency(Hz)
31.468 70.09
640x350
37.861 85.08
31.469 70.08
720x400
37.927 85.03
31.469 59.94
35.000 66.66
640x480 37.861 72.80
37.500 75.00
43.269 85.00
31.500 60.00
848x480 37.799 70.00
39.375 75.00
31.500 60.00
852x480 37.799 70.00
39.375 75.00
35.156 56.25
37.879 60.31
800x600 48.077 72.18
46.875 75.00
53.674 85.06
832x624 49.725 74.55
48.363 60.00
56.476 70.06
1024x768
60.023 75.02
68.677 85.00
54.348 60.05
1152x864 63.995 70.01
67.500 75.00
1152x870 68.681 75.06
1280x960 60.023 60.02
1280x1024 63.981 60.02

-7 -

Downloaded from www.Manualslib.com manuals search engine

 Accessories
TV/AV MULTIMEDIA

POWER

DVD
TV VCR
MODE

CABLE
STB
AUDIO

ZOOM - ZOOM +
MUTE
PIP

SLEEP LIST

TEXT/ * I/II

ARC
EXIT
MENU

OK

PIP
PR INPUT
- PIP
PIP PR + SWAP

VOL SSM PSM PR

FAVOURITE Q.VIEW

SIZE POSITION INDEX HOLD

TIME REVEAL MIX MODE

? M

LG TV

AS mark

Owner’s Manual Remote Control handset 2-Eye Bolts

1.5V
1.5V

Alkaline batteries Power Cord 2-Wall brackets

Joinning the set assembly to the wall to protect the set tumbling
- Secure the set assembly by joinning it to a wall by using the Eye Bolts/Wall brackets.

• After the set must be mounted on a desktop, install the Eye Bolts on the set as
shown.
Insert the 2 Eye Bolts and tighten securely, in the holes on the bracket.
Install the wall brackets on the wall with 2 bolts, (not supplied with the product),
as shown.
Match the height of the Eye Bolts and the wall brackets.
Check to be sure the brackets are tightened securely.

• Secure the set assembly to the wall with strong strings or wound wire cables,
(not supplied with the product), as shown.

Optional Extras
- Optional extras can be changed or modified for quality improvement without any notification new optional extras can be
added.
- Contract your dealer for buying these items.
42
40
40
42
50

Tilt wall mounting bracket Ceiling mounting bracket Video cables Audio cables

-8 -

Downloaded from www.Manualslib.com manuals search engine

 SPECIFICATIONS
NOTE : Specifications and others are subject to change without notice for improvement.

V Application Range
This spec is applied to the 42”PDP TV used MF-056A Chassis.

V Specification
Each part is tested as below without special appointment.
1) Temperature : 25±5°C (77±9°F), CST : 40±5
2) Relative Humidity: 65±10%
3) Power Voltage: Standard Input voltage (100-240V~, 50/60Hz)
* Standard Voltage of each product is marked by models.
4) Specification and performance of each parts are followed each drawing and specification by part number in accordance with BOM.
5) The receiver must be operated for about 20 minutes prior to the adjustment.

V Test Method
1) Performance : LGE TV test method followed.
2) Demanded other specification
Safety: CE, IEC specification
EMC : CE, IEC

Model Name Market Remark

42PX4RV-TA Non-EU Safety : IEC60065, EMI : CISPRI3
42PX4RV-ZA EU Safety : IEC/EN60065, EMI : EN55013, EMS : EN55020

V General Specification
1. General Specification

No Item Specification Remark

1 Display Screen Device 42 inch wide Color Display Module PDP
2 Aspect Ratio 16:9
3 PDP Module PDP42X3xxxx
RGB Closed Type, Film Filter
4 Operating Environment 1) Temp : 0~40 deg LGE SPEC
2) Humidity : 0~85%
5 Storage Environment 1) Temp : -20~60 deg
2) Humidity : 0~85%
6 Input Voltage 100-240V~, 50/60Hz Maker : SONY/ Murata/ Sanken

-9 -

Downloaded from www.Manualslib.com manuals search engine

 2. Model Specification

No Item Specification Remark

1 Market EU
2 Broadcasting system PAL B/G/I/D/K, NTSC
3 Available Channel BAND PAL NTSC
VHF/UHF C1 ~ C69 2 ~83
CATV S1 ~ S47 1 ~ 71
4 Receiving system Upper Heterodyne
5 Scart Jack(3EA) PAL, SECAM. NTSC
6 Video input(2EA) PAL, SECAM, NTSC 4 System : PAL, SECAM, NTSC,PAL60
7 S-Video Input(2EA) PAL, SECAM, NTSC 4 System : PAL, SECAM, NTSC,PAL60
8 Component Input(2EA) Y/Cb/Cr, Y/Pb/Pr
9 RGB Input(1EA) RGB-PC, RGB-DTV
10 HDMI Input(1EA) HDMI-PC, HDMI-DTV
11 Audio Input(4EA) PC Audio, Component(1EA), AV(2EA) L/R Input
12 Wired Control Discrete IR
13 Audio variable out

- 10 -

Downloaded from www.Manualslib.com manuals search engine

 ADJUSTMENT INSTRUCTIONS
1. Application Object 3-2. Channel memory Method
These instructions apply to the MF-056A Chassis. 1) Select “PDP” and “Hurricane” on Model dialog. And check
your connection in Communication dialog. (If your
connection is ‘NG’, then set your PORT(COM1,2,3,...)
2. Specification correctly.)
(1) Because this is not a hot chassis, it is not necessary to use 2) Connect RS-232C cable and turn on the power.
an isolation transformer. However, the use of isolation (If your connection has completed, you can see “Ready”.)
transformer will help protect test instrument.
(2) Adjustment must be done in the correct order. [ If your set is not an end products but only a board, you
(3) The adjustment must be performed in the circumstance of have to make your board to Stand-by state (LED_R). And
25±5°C of temperature and 65±10% of relative humidity if you have to Download in Stand_by power state.
there is no specific designation.
(4) The input voltage of the receiver must keep 100-220V,
50/60Hz.
(5) The receiver must be operated for about 15 minutes prior
to the adjustment.

O After RGB Full white HEAT-RUN Mode, the receiver must

be operated prior to adjustment.
O Enter into HEAT-RUN MODE
1) Press the POWER ON KEY on R/C for adjustment.
2) OSD display and screen display 100% full WHITE
PATTERN.

[ Set is activated HEAT-RUN without signal generator in (Fig. 3)

this mode.
[ Single color pattern(RED/BLUE/GREEN) of HEAT-RUN
mode uses to check PANEL. 3) Select proper CH_memory file(*.nvm) for each model at
[NVRAM Download] $ [Write Batch]
Caution) If you turn on a still screen more than 20 minutes Next, select proper binary file(*.bin) including the CH
(Especially digital pattern, cross hatch pattern), after information for each model at [NVRAM File].
image may be occur in the black level part of the 4) Click the [Download] button.
screen. It means the completion of the CH memory download if all
items show ‘OK’ and Status is changed by ‘PASS’ at the
lower right corner of the window.
3. Channel memory 5) If you want to check whether the CH information is
memorized correctly or not, click the [Verify] button.
3-1. Setting up the LGIDS And then compare NVRAM File(*.bin) with the CH
1) Install the LGIDS. (idsinst.exe) information downloaded.
2) After installation, restart your PC.
3) Extract [files.zip] to folder [c:\LGIDS\files].
4) Start LGIDS.

(Fig. 3-1)

3-3 Sub program download

1) Select “PDP” and “Hurricane” on Model dialog. And check
your connection in Communication dialog. (If your
connection is ‘NG’, then set your PORT(COM1,2,3,...)
(Fig. 1) correctly.)

- 11 -

Downloaded from www.Manualslib.com manuals search engine

 2) Connect RS-232C cable and turn on the power. (Use the 5. EDID (The Extended Display
special Cable For Sub-program) (If your connection has
completed, you can see “Ready”) Identification Data)/ DDC (Display
Data Channel) download
5-1. Required Test Equipment
1) Adjusting PC with S/W for writing EDID Data.(S/W : EDID
TESTER Ver.2.5)
2) A Jig for EDID Download
3) Cable : Serial(9Pin or USB) to D-sub 15Pin cable, D-sub
15Pin cable, DVI to HDMI cable

5-2. Setting of device

Each PCB assembly must be checked by check JIG set.

(Because power PCB Assembly damages to PDP Module, (Fig. 5) Connection Diagram of DDC download
especially be careful)
5.3. Preparation for Adjustment
1) As above Fig. 5, Connect the Set, EDID Download Jig, PC
4. POWER PCB Assy Voltage & Cable.
Adjustments (Va, Vs Voltage Adjustments) 2) Turn on the PC & EDID Download Jig. And Execute the
S/W : EDID TESTER Ver,2.5
4-1. Test Equipment : D.M.M. 1EA 3) Set up S/W option
Repeat Number : 5
Device Address : A0
4-2. Adjustment Method PageByte : 8
[P/No 3501V00220A(Sanken PSU) B/D] 4) Power on the Set

(1) Va Adjustment
1) After receiving 100% Full White Pattern, HEAT RUN.
2) Connect + terminal of D.M.M to Va pin of P807, connect
- terminal to GND pin of P807.
3) After turning RV501, voltage of D.M.M adjustment as
same as Va voltage which on label of panel right/top.
(Deviation; ±0.5V)

(2) Vs Adjustment
1) Connect + terminal of D.M.M to Vs pin of P807, connect
– terminal to GND pin of P805. 5.4. Sequence of Adjustment
2) After turning RV401, voltage of D.M.M adjustment as
same as Va voltage which on label of panel right/top. (1) DDC data of Analog-RGB
(Deviation; ±0.5V) 1) Init the data

2) Load the EDID data.(Open File)

[Analog-RGB : MF056A_RGB.ANA]
[digital(HDMI) : MF056A_DMI.DVI]

3) Set the S/W as below.

4) Push the “Write Data & Verify”button. And confirm “Yes”.
(Fig. 4) Connection diagram of power adjustment for measuring 5) If the writing is finished, you will see the “OK” message.

- 12 -

Downloaded from www.Manualslib.com manuals search engine

 6. Auto AV(CVBS) Color Balance W Auto adjustment Map(RS-232C)

Type MF-056A : RT-42PX40/ RZ-42PX40

6-1. Required
- This AV color balance adjustment should be performed Baud Rate Data bit Stop bit Parity
before white Balance Adjustment
115200 8 1 NONE
6-2. Required Equipment Index Cmd1 Cmd2 Data Min Value Max Value
1) Remote controller for adjustment
2) AV Pattern Generator R Gain j a 00(00) 255(FF)
: 802F Pattern Generator, Master(MSPG-925FA), etc G Gain j b 00(00) 255(FF)
(Which has PAL Composite Video format output with Protocol B Gain
standard(1.0 Vpp) Vertical 100% Color Bar Pattern as Fig6) j c 00(00) 255(FF)
Setting
R Offset j d 00(00) 255(FF)
6-3. Method of Auto Color Balance
1) Input the PAL Composite Video (Fig6. 100% Color Bar G Offset j e 00(00) 255(FF)
Pattern) into video input. B Offset j f 00(00) 255(FF)
(42PX4RV-TA : AV1/AV2 Input 50Hz,
42PX4RV-ZA : AV4/AV5 Input)
2) Set the PSM to Standard mode in Picture menu. 7-3. Adjustment of White Balance
3) Press INSTAR key on R/C for adjustment.
4) Press the G(Vol. +) key operate to set, then it becomes O Operate the zero-calibration of the CA-100, then stick
automatically. sensor to PDP module surface when you adjust.
5) Auto-RGB OK means completed adjustment. O For manual adjustment, it is also possible by the following
sequence.

1) Select white pattern of heat-run mode by pressing power

on key on remote control for adjustment then operate heat
run more than 15 minutes.
2) As below Fig.7-1, Supply 216Level (85 IRE) full screen
pattern to Video input.
(42PX4RV-TA : AV1/AV2 INPUT 50Hz,
42PX4RV-ZA : AV4/AV5 INPUT)
3) Press the TV/AV KEY on R/C for converting input mode.
4) Set the PSM to Standard mode in Picture menu.
(Fig. 6) Auto AV(CVBS) Color Balance Test Pattern 5) Enter the White Balance adjustment mode by pressing the
INSTART key twice(White Balance) on R/C.
6) Stick sensor to center of the screen and select each items
(Red/Green/Blue Gain and offset) using D / E(CH +/-) key
7. Adjustment of White Balance on R/C.
7) Adjust Only High Light with R Gain/ B Gain using F / G
7-1. Required Equipment (VOL+/-) key on R/C.
1) Remote controller for adjustment 8) Adjust it until color coordination becomes as below.
2) Color Analyzer (CA-100 or same product) (High Light G Gain : 7A // Low Light R Offset : 7F, G Offset
3) Auto W/B adjustment instrument(only for auto adjustment) 7E, B Offset 80 is Fixed)
4) AV Pattern Generator [MF-056A : 42PX4RV-TA/ZA] - VGA 42”
Bright : High Light : 80 ± 20cd
7-2. Connecting diagram of equipment for Color-Coordinate : High Light : X : 0.285 ± 0.003
measuring (For Auto Adjustment) Y : 0.295 ± 0.003
Color Temperature : 9,300°K ± 500°K
COLOR
ANALYZER 216 Level (85 IRE)
216 Level (85 IRE) TYPE ; CA-100

CVBS
signal
input
M SPG-2 1 0 0 /
M STG- 5 2 0 0

(Fig. 7-1) Pattern for Adjustment of White Balance

RS-232C Serial Communication
9) When adjustment is completed, Exit adjustment mode
(Fig. 7) Connection Diagram of Auto W/B adjustment using EXIT key on R/C

- 13 -

Downloaded from www.Manualslib.com manuals search engine

 8. Auto Component Color Balance 9. Default Value in Adjustment mode
8-1. Required Test Equipment 9-1. Auto Color Balance (Component/RGB)
1) Remote controller for adjustment
2) 802F Pattern Generator
(Which has 720p Ypbpr output & PC 1024x768 60Hz with Auto Color Balance(HEX)
Standard(0.7Vpp) Vertical 100% Color Bar Pattern as Fig.8)
Auto-RGB G To Set
8-2. Method of Auto Component Color Balance Red Offset1 80
1) Input the Component 720p 100% Color Bar signal into Green Offset1 80
Component1 or Component2.
Blue Offset1 80
2) Set the PSM to Standard mode in Picture menu.
3) Press INSTART key on R/C for adjustment.
Red Offset2 80
4) Press the G(Vol. +) key operate To set, then it becomes Green Offset2 80
automatically. Blue Offset2 80
5) Auto-RGB OK means complete adjustment Red Gain 80
Green Gain 80
Blue Gain 80
Reset G To Set

(Fig. 10) Default Value on OSD

9-2. White Balance

White Balance(Hex)
(Fig. 8) Auto Component Color Balance Test Pattern
Red Gain 80
Red Offset 80
Green Gain 80
9. Auto RGB Color Balance Green Offset 80
9-1. Required Test Equipment Blue Gain 80
1) Remote controller for adjustment Blue Offset 80
2) 802F Pattern Generator, Master (MSPG-925FA), etc. Reset G To Set
(Which has XGA 60Hz PC Format output with standard
(0.7Vpp) horizontal black and white pattern as Fig.10)
(Fig. 10-1) Default Value on OSD
9-2. Method of Auto RGB Color Balance
1) Input the PC 1024x768 60Hz horizontal black and white
pattern into RGB.
2) Set the PSM to Standard mode in Picture menu.
3) Press ADJ key on R/C for adjustment.
4) Press the G(Vol. +) key operate To set, then it becomes
automatically.
5) Auto-RGB OK means completed adjustment.

Level : 0

Level : 255

(Fig. 9) Auto RGB Color Balance Test Pattern

- 14 -

Downloaded from www.Manualslib.com manuals search engine

 TROUBLE SHOOTING GUIDE

1. Power Board
1-1. The whole flowchart which it follows in voltage output state

Start check

Doesn't the Yes Is it identical No Is the Interface

screen whole come with Power Off signal operated?
out? condition?

Yes Yes

No 1. Check the Power Off 2. Check the Interface

condition. signal condition.

Doesn't the Yes Doesn't the No Doesn't the No Doesn't the

low pressure output St-by 5V signal 5V Monitor signal VSC signal RL-ON
come out? come out? come out? come out?

Yes Yes Yes

No 3. Check the St-by 5V 4. Check the 5V Monitor 5. Check the VSC RL-ON
signal circuit. signal circuit. signal.

No

Doesn't the Yes Doesn't the No Doesn't the Doesn't the

high tension output VSC signal Vs-ON Vs, Va voltage output VSC low pressure
come out? come out? come out? output come out?

Yes Yes Yes

No 7. Check the VSC Vs-ON 8. Check the Vs, Va 6. Check the VSC low
signal voltage output circuit. pressure output

When the When the When the

Does Y, Z B/D Module Y B/D Module Z B/D Module
high tension Yes input connector is remove, No No
input connector is input connector is
output voltage Drop does Power Board hightension removed, does output removed, does output
occur? output voltage Drop voltage drop voltage Drop
occur? occur? occurs?
No
Yes Yes Yes

9. Check the Power 10. Check the Z B/D 11. Check the Y B/D
Manufacture enterprise Board Output high Module output circuit Module output circuit
meaning of a passage tension circuit

- 15 -

Downloaded from www.Manualslib.com manuals search engine

 1-2. Sony Power Board Structure

T502: Vs Trans
T702: Va Trans
T101: St-by Trans
1 2 3
T103: Low Voltage Trans

- 16 -

Downloaded from www.Manualslib.com manuals search engine

 1-3. Sanken, LGIT Power Board Structure

T221: Vs Trans
T271: Va Trans
T121: St-by Trans
1 2 3
T201: Low Voltage Trans

- 17 -

Downloaded from www.Manualslib.com manuals search engine

 2. No Power
(1) Symptom
Ø Does’t minute discharge at module.
Ø Non does not come in into the front LED.

(2) Check following

No
Is plug in power cord? Plug in power cord.

Yes

Is the Line Filter and Power No

Connect the Cable.
Board Cable connected?

Yes

Is the Fuse(F101) on No
Replace the Fuse.
Power Board normal?

Yes

Is the Power Board and 7P of No

Connect the Cable.
VSC Board Cable connected?

Yes

After the cable connect is remved

to Power Board(except the CN101
connection cable), the AC voltage
marking is authorized on manual.
When ST-BY 5V is not operated,
replace Power Board.

- 18 -

Downloaded from www.Manualslib.com manuals search engine

 3. Protect Mode
(1) Symptom
Ø After once shining, it does not discharge minutely
from module
Ø The Rely falls(The sound is audible “click”)

Ø It is converted with the color where the front LED

is red from green.

(2) Check following

No No
Is the Power Board Is output the normality Low/High Replace Power
normal ? voltage except Stand-by 5V? Board.

Yes

No No
Is the each connector After connecting well each connector, Replace the
normal? the normality it operates? connector.

Yes
Is the output voltage
No Yes Yes Replace
Is the Y-Board Is the Fuse(FS2) on Y-B/D normal? normal after remove
normal? (In case of open is replace) P5, P6 connector of Y-Board.
Y-B/D?
Yes
Is the output voltage
No Yes Yes Replace
Is the Z-Board Is the Fuse (FS1, FS2) on Z-B/D normal after remove
normal? normal? (In case of open is replace) P1 connector of Z- Z-Board.
B/D?
Yes
After remove P1, P2, P3 output voltage
No Is the output voltage normal after Yes
Is the X- Board normality: Replace Right X-B/D
remove P1, 2, 3, 4, 5 connector of
normal? After remove P4, P5 output voltage
X-B/D?
normality: Replace Left X-B/D
Yes

No Is the output voltage normal after Yes

Is the Ctrl Board Replace
remove P1, 2, 4, 9, 10 connector of
normal? X-Board.
Ctrl-B/D?
Yes

No Yes
Is the Is the output voltage normal after After remove P1001, 1100 normal
VSC Board normal? remove P1001, P1100? operation: Replace VSC Board

Yes

No After crisis COF of each board, check the normality operates.

Is the COF of X, Y, Z
normal ? If in case normality operates, correspondence COF Fail is
replace the module.

- 19 -

Downloaded from www.Manualslib.com manuals search engine

 4. No Raster
(1) Symptom
Ø Does’t minute discharge at module.
Ø It maintains the condition where the front LED is green.

(2) Check following

No No
Is the Power Board Is output the normality Low/High Replace the
normal? voltage except Stand-by 5V? Power Board.

Yes

No No
Is the each connector After connecting well each connector, Replace the
normal? the normality it operates? connector.

Yes
Is the output voltage
No Yes Yes Replace
Is the Y-Board Is the Fuse(FS2) normal on Y-B/D? normal after remove
normal? (In case of open is replace) P5, P6 connector of Y-Board.
Y-B/D?
Yes
Is normal the output
No Yes Yes Replace
Is the Is the Fuse(FS1, FS2) normal on voltage after remove
Z- Board normal? Z-B/D? (In case of open is replace) P1 connector of Z-Board.
Z-B/D?
Yes
After remove P1, P2, P3 output voltage
No Is the output voltage normal after Yes
Is the normality: Replace Right X-B/D
remove P1, 2, 3, 4, 5 connector of
X- Board normal? After remove P4, P5 output voltage
X-B/D?
normality: Replace the Left X-B/D
Yes

No Is the output voltage normal after Yes

Is the Replace
remove P1, 2, 4, 9, 10 connector of
Ctrl Board normal? X-Board.
Ctrl-B/D?
Yes

No Yes
Is the Is the output voltage normal after After remove P1001, P1100 normal
VSC Board normal? remove P1001, P1100? operation: Replace the VSC Board

Yes

No After crisis COF of each board, check the normality operates.

Is the COF of X, Y, Z
normal? If in case normality operates, correspondence COF Fail is
replace the module.

- 20 -

Downloaded from www.Manualslib.com manuals search engine

 5. In case of occurring strange screen into specific mode
5-1. In case the OSD does not displayed
(1) Symptom
Ø LED is green
Ø The minute discharged continuously becomes
accomplished from module

(2) Check following

Is the LVDS cable No Is the LVDS cable Yes

Replace the cable.
normal ? connected well?

No

Cable inserts well.

Yes

Is the VSC Board No Does the FIL8532 IC Yes

Replace VSC B/D
normal? (IC800) Operates ?

No

Replace FIL8532
Yes IC(IC800).

Is the Ctrl Board of No

Replace Ctrl B/D.
Module normal?

- 21 -

Downloaded from www.Manualslib.com manuals search engine

 5-2. In case of does’t display the screen into specific mode
(1) Symptom
Ø The screen does not become the display from specific input mode
(RF, AV, Component, RGB, DVI).

(2) Check following

Ø Check the all input mode should become normality display.
Ø Check the Video(Main)/Data(Sub), Video(Main)/Video(Sub) should become
normality display from the PIP mode or DW mode. (Re-Check it Swap)

(3) In case of becomes unusual display from RF mode

No Is the Tuner Cable Yes Is the Input voltage, IIC Communication
Is the Tuner normal?
connected well? and CVBS output normal?

No No
Yes
Cable inserts well. Replace the Tuner

No Is the Input voltage, IIC No

Is the CXA2069Q
Communication and HV sync Replace the IC
normal?
normal?

Yes

Is the FIL8532 No Is normal the Input voltage, IIC No

Replace the IC
normal? Communication and HV sync?

(4) In the case of becomes unusual display from RF, AV mode

No Is the Input voltage, IIC No
Is the CXA2069Q
Communication and HV sync Replace the IC
normal?
normal?
Yes
No Is the Input voltage, IIC No
Is the FIL8532
Communication and HV sync Replace the IC
normal?
normal?

(5) In the case of becomes unusual display from Component, RGB mode
No Is the Input voltage, IIC No
Is the FIL8532
Communication and HV sync Replace the IC
normal?
normal?

(6) In the case of becomes unusual display from HDMI mode

No Is the Input voltage, IIC No
Is the Sil9011
Communication and HV sync Replace the IC
normal?
normal?
Yes
No Is the Input voltage, IIC No
Is the FIL8532
Communication and HV sync Replace the IC
normal?
normal?

- 22 -

Downloaded from www.Manualslib.com manuals search engine

 6. In case of no sound
(1) Symptom
Ø LED is green
Ø Screen display but sound is not output

(2) Check following

No Yes
Is the SPK cable Is the SPK cable
Replace SPK cable
normal? connected well?

No

Yes
Cable inserts well.

No Yes Yes
Is the RF/ AV/ Does IC400 Does IC401 Does IC402
Component/ RGB/ Operates ? Operates ? Operates ?
HDMI sound normal?
No No No

Replace IC400 Replace IC401 Replace IC402

Replace
VSC B/D

- 23 -

Downloaded from www.Manualslib.com manuals search engine

 BLOCK DIAGRAM

’
cable

- 24 -

Downloaded from www.Manualslib.com manuals search engine

 MEMO

- 25 -

Downloaded from www.Manualslib.com manuals search engine

 EXPLODED VIEW

121

300

600 601

305
531
301
530

570

120 304
700

302

200

303

206

205 201

202
204

203

591 580
590
501
520

410

401

400

430

- 26 -

Downloaded from www.Manualslib.com manuals search engine

 EXPLODED VIEW PARTS LIST
No. Part No. Descriptions

120 6401900114A SPEAKER ASSEMBLY, 42PX40 SPK ASSY RIGHT FOR LGEMA

EAB31838901 Speaker Assembly, 6401VD0024A 42PX40 SPK ASSY R KOREA TOPTONE

121 6401900115A SPEAKER ASSEMBLY, 42PX40 SPK ASSY LEFT FOR LGEMA

EAB31839101 Speaker Assembly, 6401VD0025A 42PX40 SPK ASSY L KOREA TOPTONE

200 6348Q-E066B PDP,Module-XGA PDP42X30000.AKLGG XGA 42INCH 1024X768 16/9

6348Q-E123P PDP, 42” 1024*768 PDP42X30000.ADLGB

201 6871QCH077A/ B PWB(PCB) ASSEMBLY,DISPLAY CTRL ASSY HAND INSERT 42”HD 42X3

202 6871QDH117A PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 42”HD 42X3

203 6871QLH059A PWB(PCB) ASSEMBLY,DISPLAY XRLT ASSY HAND INSERT 42”HD 42X3

204 6871QRH068A PWB(PCB) ASSEMBLY,DISPLAY XRRT ASSY HAND INSERT 42”HD 42X3

205 6871QYH053B PWB(PCB) ASSEMBLY,DISPLAY YSUS ASSY HAND INSERT 42”HD 42X3 VER.B

206 6871QZH056B PWB(PCB) ASSEMBLY,DISPLAY ZSUS ASSY HAND INSERT 42”HD 42X3 VER.B

300 3091V00739G Cover Assembly, 42PX4R-ZA STEREO E_PHONE 3090V00634 AF-342 ABS LG

3091V00739N CABINET ASSEMBLY, 42PX4R-ZA STEREO E_PHONE LGEFS (SKD)

301 4980V01128B/ C Supporter, COMPLEX ASSY AL 0.8T TOP

302 4980V01130B/ C Supporter, COMPLEX ASSY AL 0.8T BOTTOM

303 4980V01132B/ C Supporter, COMPLEX ASSY AL 0.8T RIGHT

304 4980V01134B/ C Supporter, COMPLEX ASSY AL 0.8T LEFT

305 3790V00709C FILTER(MECH), RT-42PX10 LGM42-09 MITSUI 42” ETCHING MESH GLASS FILTER

400 3809V00513J/ W Cover Assembly, back cover

401 3301V00049B PLATE ASSEMBLY, ASSY 3300V00440A RZ-42PX40 MF056A

410 4980V00C84A/ D Supporter, COMPLEX ASSY AL

430 3501V00216A/ H Base Assembly, ASSY STAND

501 3301V00055A PLATE ASSEMBLY, AV 3301V00053 3301V00054 42PX4RV-TA ASSY

520 68719MMW13A PWB(PCB) ASSEMBLY,MAIN MAIN1 M.I MF056A 42PX4R-ZA .SKD MAIN X3

68719MMW38A PCB Assembly,Main MAIN1 M.I MF056B 42PX4R .SET DMS X3

530 6871VSMS65A PWB(PCB) ASSEMBLY,SUB CONT MF056A HURRICANE2

531 5020V01022B BUTTON, CONTROL DU-42PX51X ABS, AF-303S 8KEY TITAN GRAY

570 68719SML88A PCB Assembly,Sub SUB M.I MF056A 42PX4R-ZA SET INDEX ASSY

6871VSMS27A PWB(PCB) ASSEMBLY,SUB LED MF056A H2 RT-42PX40X INDEX

580 3501V00220A POWER SUPPLY ASSEMBLY, HURRICANE2 FREE VOLTAGE SANKEN 42” PSU

590 6200J000115 Filter,AC Line IJ-N06CESL1 5.3mH 250VAC 6A 0.22uF 1000pF

591 4980V00C50C/ E Supporter, PRESS SECC T1.2 FILTER SECC(EGI) SUPP.LINE FILTER

600 68719SMH12A PWB(PCB) ASSEMBLY,SUB M.I MF056A H2 SIDE AV , DMS

601 4811V00173C Bracket Assembly, SIDE AV RZ-42PX40 AF05GB ASSY SIDE AV

4811V00357A BRACKET ASSEMBLY, SIDE AV 42PX4RV-ZA MF056A FOR LGEMA PHANTOM

700 6500VR0002A SENSOR, YGCA-T068A AMBIENT LIGHT DIGITAL EYE SENSOR ASSY

- 27 -

Downloaded from www.Manualslib.com manuals search engine

 REPLACEMENT PARTS LIST
LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION
Q1003 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC
Q1004 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC1000 0IPRPML001A MIC39100 MICREL 3P SOT223 R/TP Q101 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC1001 0IMCRRH001A BA033FP-E2 ROHM 3P-SOP,TO252-3 Q102 0TR102008AA KRA102S R/TP KEC SOT23 CHIP TR
IC1002 0IMCRFA010A KA7809R, FAIRCHILD 2P D-PAK, R/TP Q103 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC1003 0IPMG00027A SC156515M-1.8TR SEMTECH 5P/TO-263-5 Q103 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC1004 0IMCRRH001A BA033FP-E2 ROHM 3P-SOP,TO252-3 Q104 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC1005 0IMCRRH001A BA033FP-E2 ROHM 3P-SOP,TO252-3 Q104 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC101 0IMI623200B M62320FP,I/O EXPANDER 16P SOP Q105 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC102 0IMCRFA015A KA7805R FAIRCHILD 2P D-PAK R/TP 500MA Q106 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC1100 0IMCRRH001A BA033FP-E2 ROHM 3P-SOP,TO252-3 Q107 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC1101 0IPRPML001A MIC39100 MICREL 3P SOT223 R/TP Q108 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC1102 0IPMG00027A SC156515M-1.8TR SEMTECH 5P/TO-263-5 Q1200 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC1103 0IPMGKE030A KIA78R05F KEC 5PIN DPAK R/TP 1A,5V Q200 0TR150400BA CHIP 2SA1504S(ASY) BK KEC
IC1104 0IPMG00027A SC156515M-1.8TR SEMTECH 5P/TO-263-5 Q201 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC1105 0IPRPML001A MIC39100 MICREL 3P SOT223 R/TP Q202 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC1200 0IPRPS5005A SII9011CLU(PB FREE) SILICON IMAGE 128P,LQFP Q203 0TR150400BA CHIP 2SA1504S(ASY) BK KEC
IC1201 0IMMRAL014B AT24C02N-10SI-2.7 ATMEL 8P SOIC R/TP Q204 0TR150400BA CHIP 2SA1504S(ASY) BK KEC
IC1300 0IMCRTH003B THC63LVD104A,PB FREE(F) Q205 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC202 0IPMGON013B MC34063ADR2G ON SEMI SO-8P R/TP Q206 0TR150400BA CHIP 2SA1504S(ASY) BK KEC
IC300 0ISO206900A CXA2069Q QFP64 BK I2C BUS AV S/W Q207 0TR150400BA CHIP 2SA1504S(ASY) BK KEC
IC301 0ISA721700C LA7217M MFP14 TP SYNC SEPARATOR Q209 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC400 0IMCRMN028B MSP4410K MICRONAS 80P/PQFP Q210 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC401 0ILNR00015A NSP-2100A,LF NEOFIDELITY TQFP 64P Q300 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC402 0IMCRTI028C TAS5122DCARG4,LF 56P/TSSOP R/TP Q301 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC404 0IPH741400E 74HC14D 14SOP TP SHITTER TRIGGER Q302 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC500 0IMMRAL014B AT24C02N-10SI-2.7 ATMEL 8P SOIC Q303 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC502 0IPH741400E 74HC14D 14SOP TP SHITTER TRIGGER Q304 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC600 0IPRP00009A ICL3232CBNZ INTERSIL 16P/SOP R/TP Q305 0TR150400BA CHIP 2SA1504S(ASY) BK KEC
IC601 0IPMGKE032A KIA78R09F KEC 5PIN DPAK R/TP 1A,9V Q400 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC602 0IPMGKE032A KIA78R09F KEC 5PIN DPAK R/TP 1A,9V Q401 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC603 0IPRPNS054A LM75CIMX-3 8P/SOP R/TP TEMPERATURE SENSOR Q402 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC700 0IMCR02006A FLI8125BB-LF GENESIS 208P/PQFP Q403 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC701 0IMMRAL025A AT24C32AN-10SI-2.7 ATMEL 8PIN SOP TP 32K 3.3V Q404 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC703 0IMMR00004A SST25VF040-20-4C-S2AE-T SST SOIC 8P Q405 0TR102008AA KRA102S R/TP KEC SOT23 CHIP TR
IC800 0IMCR02005A FLI8532BD-LF GENESIS 416P/PBGA Q407 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC802 0IMMR00024A 24LC256T-I/SMG(PB FREE) Q408 0TR102008AA KRA102S R/TP KEC SOT23 CHIP TR
IC901 0IMMR00002A K4D261638F-LC50,LF TSOPII 66P Q409 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
IC902 0IMMR00002A K4D261638F-LC50,LF TSOPII 66P Q410 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
Q411 0TR387500AA CHIP 2SC3875S(ALY) BK KEC
TRANSISTOR
IC104 0TR830009BA BSS83 TP PHILIPS N-CHANNEL S/W TR DIODE
IC105 0TR830009BA BSS83 TP PHILIPS N-CHANNEL S/W TR D1005 0DD226239AA KDS226 TP KEC
IC1202 0TR830009BA BSS83 TP PHILIPS N-CHANNEL S/W TR D1006 0DD226239AA KDS226 TP KEC
IC1203 0TR830009BA BSS83 TP PHILIPS N-CHANNEL S/W TR D1007 0DD226239AA KDS226 TP KEC
IC200 0TR830009BA BSS83 TP PHILIPS N-CHANNEL S/W TR D1008 0DD226239AA KDS226 TP KEC
IC201 0TR830009BA BSS83 TP PHILIPS N-CHANNEL S/W TR D1009 0DD226239AA KDS226 TP KEC
IC503 0TR830009BA BSS83 TP PHILIPS N-CHANNEL S/W TR D1010 0DD226239AA KDS226 TP KEC
IC504 0TR830009BA BSS83 TP PHILIPS N-CHANNEL S/W TR D1012 0DD200009AF RU2M V(1) TP R-TMD 400V 1.1A 20A 0.4US 10UA
Q100 0TR387500AA CHIP 2SC3875S(ALY) BK KEC D1013 0DD200009AF RU2M V(1) TP R-TMD 400V 1.1A 20A 0.4US 10UA
Q1000 0TR387500AA CHIP 2SC3875S(ALY) BK KEC D102 0DD226239AA KDS226 TP KEC
Q1001 0TR387500AA CHIP 2SC3875S(ALY) BK KEC D103 0DD226239AA KDS226 TP KEC
Q1002 0TR387500AA CHIP 2SC3875S(ALY) BK KEC D104 0DD226239AA KDS226 TP KEC

- 28 -

Downloaded from www.Manualslib.com manuals search engine

 For Capacitor & Resistors, CC, CX, CK, CN : Ceramic RD : Carbon Film
the charactors at 2nd and 3rd CQ : Polyestor RS : Metal Oxide Film
digit in the P/No. means as CE : Electrolytic RN : Metal Film
follows; RF : Fusible

LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION

D105 0DD226239AA KDS226 TP KEC C1073 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD
D106 0DD226239AA KDS226 TP KEC C108 0CE227SF6DC 220UF MVG 16V 20% R/TP(SMD) SMD
D108 0DD226239AA KDS226 TP KEC C1082 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
D1100 0DD226239AA KDS226 TP KEC C1083 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
D1105 0DD226239AA KDS226 TP KEC C1084 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
D1106 0DD226239AA KDS226 TP KEC C1085 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
D1107 0DD226239AA KDS226 TP KEC C1087 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD
D1109 0DD226239AA KDS226 TP KEC C109 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD
D1110 0DD226239AA KDS226 TP KEC C1098 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
D112 0DD226239AA KDS226 TP KEC C1099 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
D113 0DD226239AA KDS226 TP KEC C1102 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
D114 0DD226239AA KDS226 TP KEC C1105 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
D1200 0DD184009AA KDS184 TP KEC - 85V - 300MA C1107 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
D1201 0DS113379BA 1SS133 T-72 TP ROHM KOREA DO34 90V C1108 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
D300 0DD226239AA KDS226 TP KEC C1110 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD
D500 0DD226239AA KDS226 TP KEC C1115 0CE477DJ618 470UF STD 35V 20% FL TP 5
D501 0DD226239AA KDS226 TP KEC C1116 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD
D502 0DD226239AA KDS226 TP KEC C1117 0CE227VF6DC 220UF MV 16V 20% R/TP(SMD) SMD
D504 0DR050008AA SD05.TC R/TP SEMTECH SOD323 5V 5A 15A C1118 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD
D505 0DR050008AA SD05.TC R/TP SEMTECH SOD323 5V 5A 15A C1119 0CE477DJ618 470UF STD 35V 20% FL TP 5
D506 0DR050008AA SD05.TC R/TP SEMTECH SOD323 5V 5A 15A C1120 0CE227VF6DC 220UF MV 16V 20% R/TP(SMD) SMD
D600 0DD100009AM EU1ZV(1) TP E/EO-TMD 200V 0.25A 15A 0.4US C1126 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD
ZD100 0DR050008AA SD05.TC R/TP SEMTECH SOD323 5V 5A 15A C113 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD
ZD101 0DR050008AA SD05.TC R/TP SEMTECH SOD323 5V 5A 15A C1135 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
ZD107 0DR050008AA SD05.TC R/TP SEMTECH SOD323 5V 5A 15A C1136 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
ZD300 0DR050008AA SD05.TC R/TP SEMTECH SOD323 5V 5A 15A C1137 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
ZD301 0DR050008AA SD05.TC R/TP SEMTECH SOD323 5V 5A 15A C1138 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
ZD400 0DZRM00248A RLZ8.2B-TE11 ROHM R/TP LLDS(LL-34) 500MW C114 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD
ZD600 0DR050008AA SD05.TC R/TP SEMTECH SOD323 5V 5A 15A C1148 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
C1149 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
CAPACITOR
C1150 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C1000 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD C1151 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C1005 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD C1154 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
C1007 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C1159 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
C1009 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C116 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD
C1010 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C1162 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C1019 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C1165 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C1022 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C1166 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C103 0CE4763F618 47UF SRE,SE 16V 20% FL TP 5 C117 0CE227SF6DC 220UF MVG 16V 20% R/TP(SMD) SMD
C1030 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C118 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD
C1043 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C1185 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
C1046 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD C1186 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
C1047 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C1187 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
C1050 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD C1188 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C1051 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD C1189 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C1064 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C119 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD
C1065 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C1190 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C1066 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C1191 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C1067 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C1192 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C1068 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C1193 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C1069 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C1194 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD
C1071 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD C1195 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP

- 29 -

Downloaded from www.Manualslib.com manuals search engine

 For Capacitor & Resistors, CC, CX, CK, CN : Ceramic RD : Carbon Film
the charactors at 2nd and 3rd CQ : Polyestor RS : Metal Oxide Film
digit in the P/No. means as CE : Electrolytic RN : Metal Film
follows; RF : Fusible

LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION

C1199 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C300 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C120 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD C304 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C1200 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD C305 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C1201 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD C307 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
C121 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD C310 0CK225DFK4A 2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
C1225 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD C315 0CK225DFK4A 2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
C1230 0CK105DF64A 1UF 2012 16V 20% F(Y5V) R/TP C318 0CK225DFK4A 2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
C1231 0CK105DF64A 1UF 2012 16V 20% F(Y5V) R/TP C319 0CK225DFK4A 2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
C1245 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD C320 0CK225DFK4A 2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
C1247 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C321 0CK225DFK4A 2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
C129 0CE227SF6DC 220UF MVG 16V 20% R/TP(SMD) SMD C325 0CK225DFK4A 2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
C130 0CE227SF6DC 220UF MVG 16V 20% R/TP(SMD) SMD C328 0CK225DFK4A 2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
C1302 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C330 0CK225DFK4A 2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
C1304 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C338 0CK225DFK4A 2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
C1306 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C340 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
C1309 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C342 0CE105SK6DC 1UF MVG 50V 20% SMD R/TP
C131 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C347 0CE105SK6DC 1UF MVG 50V 20% SMD R/TP
C1311 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C402 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
C1312 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C403 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C1313 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C413 0CE335VK6DC 3.3UF MV 50V 20% R/TP(SMD) SMD
C1314 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C418 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C1315 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C425 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C1316 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C444 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C1317 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C451 0CK105DF64A 1UF 2012 16V 20% F(Y5V) R/TP
C1318 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C456 0CK105DF64A 1UF 2012 16V 20% F(Y5V) R/TP
C1333 0CE336VF6DC 33UF MV 16V 20% R/TP(SMD) SMD C457 0CE335VK6DC 3.3UF MV 50V 20% R/TP(SMD) SMD
C1334 0CE336VF6DC 33UF MV 16V 20% R/TP(SMD) SMD C462 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C1335 0CE336VF6DC 33UF MV 16V 20% R/TP(SMD) SMD C463 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD
C1338 0CE336VF6DC 33UF MV 16V 20% R/TP(SMD) SMD C464 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD
C135 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C465 0CE106SK6DC 10UF MVG 50V 20% SMD R/TP
C1414 0CE475SK6DC 4.7UF MVG 50V 20% SMD R/TP C480 0CE108DJ618 1000UF STD 35V 20% FL TP 5
C1415 0CE475SK6DC 4.7UF MVG 50V 20% SMD R/TP C481 0CE475SK6DC 4.7UF MVG 50V 20% SMD R/TP
C1419 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD C482 0CE475SK6DC 4.7UF MVG 50V 20% SMD R/TP
C1420 0CK105DF64A 1UF 2012 16V 20% F(Y5V) R/TP C483 0CF4741L438 0.47UF D 63V 5% TP 5 M/PE NI
C1424 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD C484 0CF4741L438 0.47UF D 63V 5% TP 5 M/PE NI
C1425 0CE106SH6DC 10UF MVG 25V 20% SMD R/TP C495 0CE108DJ618 1000UF STD 35V 20% FL TP 5
C1428 0CE106SH6DC 10UF MVG 25V 20% SMD R/TP C527 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
C1438 0CE106SH6DC 10UF MVG 25V 20% SMD R/TP C610 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP
C1441 0CE106SH6DC 10UF MVG 25V 20% SMD R/TP C614 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
C1506 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP C615 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
C203 0CE475SK6DC 4.7UF MVG 50V 20% SMD R/TP C620 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
C204 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD C621 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
C208 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD C622 0CE476SF6DC 47UF MVG 16V 20% SMD R/TP
C210 0CE475SK6DC 4.7UF MVG 50V 20% SMD R/TP C728 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C211 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD C729 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C214 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD C730 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C215 0CE475SK6DC 4.7UF MVG 50V 20% SMD R/TP C731 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C221 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD C735 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C238 0CE107SF6DC 100UF MVG 16V 20% SMD R/TP C737 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C241 0CE476SK6D8 47UF MVG,MC 50V 20% SMD TAPPING C739 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C245 0CE227SF6DC 220UF MVG 16V 20% R/TP(SMD) SMD C745 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C246 0CE227SF6DC 220UF MVG 16V 20% R/TP(SMD) SMD C750 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP

- 30 -

Downloaded from www.Manualslib.com manuals search engine

 For Capacitor & Resistors, CC, CX, CK, CN : Ceramic RD : Carbon Film
the charactors at 2nd and 3rd CQ : Polyestor RS : Metal Oxide Film
digit in the P/No. means as CE : Electrolytic RN : Metal Film
follows; RF : Fusible

LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION

C752 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP P1100 366-921J GIL-G-10P LGC 10PIN 2.54MM STICK
C760 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP P1101 366-921F GIL-G-07P LGC 7PIN 2.54MM STICK
C762 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP P1300 6602T12007D GT121-31P-TD LGC 31P 1.25MM DUAL S/T
C764 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP P1302 6630VF00710 12505WS-10A00 YEONHO 10P 1.25MM VERTICAL
C767 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP P300 366-922L GIL-G-12P LGC 12PIN 2.54MM RIGHT ANGLE
C771 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP P400 366-932C IL-G-04P LGC 2.5MM S/T STICK
C828 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD P401 366-932B IL-G-03P LGC 2.5MM S/T STICK
C832 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP P800 6602T12006M 53398-1390 MOLEX 13P 1.25MM S/T SMD
C833 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP P801 366-932E GIL-G-06P LGC 6PIN 2.54MM STICK
C834 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP P803 6602T12007D GT121-31P-TD LGC 31P 1.25MM DUAL S/T
C835 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
RESISTOR
C836 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C837 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP AR1200 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES
C838 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP AR1201 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES
C839 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP AR1202 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES
C840 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP AR1203 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES
C851 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP AR1204 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES
C853 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP AR1205 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES
C884 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP AR1301 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES
C896 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP AR1302 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES
C901 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP AR1303 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES
C904 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP AR1304 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES
C905 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP AR1305 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES
C930 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP AR1306 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES
C950 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP AR700 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES
AR701 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES
COIL
AR702 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES
L1000 6140VB0004B 26UH 1UEWPHY 22.5TURN YL-9N 0.4 AR703 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES
L1101 6140VB0004B 26UH 1UEWPHY 22.5TURN YL-9N 0.4 AR704 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES
L1102 6140VB0004B 26UH 1UEWPHY 22.5TURN YL-9N 0.4 AR705 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 SERIES
L1103 6140VB0004B 26UH 1UEWPHY 22.5TURN YL-9N 0.4 R230 0RD0331H609 3.3 OHM 1/2 W 5.00% TA52
L1104 6140VB0004B 26UH 1UEWPHY 22.5TURN YL-9N 0.4 R618 0RD0562H609 56 OHM 1/2 W 5.00% TA52
L1124 6140VB0004B 26UH 1UEWPHY 22.5TURN YL-9N 0.4
6140VB0032A DBF-1015A 15.5UH 10PIE DIGITAL AUDIO
LED
L404
L405 6140VB0032A DBF-1015A 15.5UH 10PIE DIGITAL AUDIO D1003 0DL233309AC SAM2333 TP GREEN:10MCD, RED:6MCD
L406 6140VB0032A DBF-1015A 15.5UH 10PIE DIGITAL AUDIO D1103 0DL233309AC SAM2333 TP GREEN:10MCD, RED:6MCD
L407 6140VB0032A DBF-1015A 15.5UH 10PIE DIGITAL AUDIO IC103 6301V00004A YANGWOO LED ASSEMBLY RT-42PX41 WHITE

COIL SWITCH
C1 387-G07J 7P 2.5MM 500MM H-H UL1007AWG26 SW101 140-315A SKHV17910B 12V 0.05A HORIZONTAL 160G
C2 387-J06L 6P 2.5MM 700MM H-H UL1185AWG26 SW102 140-315A SKHV17910B 12V 0.05A HORIZONTAL 160G
C3 387-J12L 12P 2.5MM 700MM H-H UL1185AWG26 SW103 140-315A SKHV17910B 12V 0.05A HORIZONTAL 160G
C4 6631V00045B 10P SPECIAL 150MM H-H UL1007AWG24 SW104 140-315A SKHV17910B 12V 0.05A HORIZONTAL 160G
C5 6631V12047L 13P 1.25MM 700MM H-H UL1061AWG28 SW105 140-315A SKHV17910B 12V 0.05A HORIZONTAL 160G
C6 6631V25083A 7P 2.5MM 100MM H-H UL1007 AWG24 SW106 140-315A SKHV17910B 12V 0.05A HORIZONTAL 160G
C7 6631V39013N 8P 3.96MM 900MM H-H UL1617AWG22 SW107 140-315A SKHV17910B 12V 0.05A HORIZONTAL 160G
C8 6631V39018B 9P 3.96MM 300MM H-H UL1007AWG18 SW108 140-315A SKHV17910B 12V 0.05A HORIZONTAL 160G
JK500 6630G70016A A03-7071-094 SPG 15P 2.29MM SW700 6600VR1004A SKHMPW 5P CHIP J-ALPS .V .A HORIZONTAL .G
JK601 6630G70017A A02-0915-101 SPG 9P 2.54MM RS232 VERTICAL SW800 6600VR1004A SKHMPW 5P CHIP J-ALPS .V .A HORIZONTAL .G
P1001 366-921F GIL-G-07P LGC 7PIN 2.54MM STICK
P101 366-921L GIL-G-12P LGC 12PIN 2.54MM STICK
FILTER & CRYSTAL
P101 6602T12002M 53261-1390 MOLEX 13P 1.25MM R/A SMD L100 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM

- 31 -

Downloaded from www.Manualslib.com manuals search engine

 LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION

L1004 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L115 6200JB8010L MLB-201209-1000L-N2 R/TP 1000OHM 350MA
L1005 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L119 6200JB8010L MLB-201209-1000L-N2 R/TP 1000OHM 350MA
L1006 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L120 6200JB8010L MLB-201209-1000L-N2 R/TP 1000OHM 350MA
L1007 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L1204 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1008 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L1205 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1009 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L1206 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L101 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L1207 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1010 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L1208 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1011 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L1209 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1012 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L121 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1013 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L122 6210VC0005A BK2125 HS 750 2X1.25X0.85MM R/TP
L1014 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L123 6210VC0005A BK2125 HS 750 2X1.25X0.85MM R/TP
L1015 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L124 6210VC0005A BK2125 HS 750 2X1.25X0.85MM R/TP
L1016 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L125 6210VC0005A BK2125 HS 750 2X1.25X0.85MM R/TP
L1017 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L126 6210VC0005A BK2125 HS 750 2X1.25X0.85MM R/TP
L1018 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L1301 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1019 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L200 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L102 6210VC0006A FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP L201 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1020 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L202 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1021 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L203 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1022 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L204 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1023 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L300 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1024 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L301 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1025 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L302 6200JB8010L MLB-201209-1000L-N2 R/TP 1000OHM 350MA
L104 6210VC0006A FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP L400 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L110 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L401 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1105 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L402 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1106 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L403 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1107 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L408 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1108 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L409 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1109 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L410 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L111 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L500 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1110 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L502 6200JB8010L MLB-201209-1000L-N2 R/TP 1000OHM 350MA
L1111 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L503 6200JB8010L MLB-201209-1000L-N2 R/TP 1000OHM 350MA
L1112 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L506 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1113 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L604 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1115 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L606 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1116 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM L802 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1117 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM X1200 6212AB2845A RESONATOR,CRYSTAL ABLS-27.000MHZ
L1118 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM X300 166-E02F RESONATOR,CERAMIC CSBLA500KECZF09-B0
L1119 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM X400 156-A02M RESONATOR,CRYSTAL HC49U 18.432MHZ
L1120 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM X700 6212AB2844A RESONATOR,CRYSTAL ABLS-19.6608MHZ
L1121 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM X800 6212AB2844A RESONATOR,CRYSTAL ABLS-19.6608MHZ
L1122 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
JACK
L1123 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM
L1125 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM JK100 6612J00043C UPJ-R1-031 S/T,SCART,SHIELD,SPRING
L1126 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM JK101 6612J00043C UPJ-R1-031 S/T,SCART,SHIELD,SPRING
L1127 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM JK101 6613V00026A UJB-03-28A UGCOM 6613V00004S
L1128 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM JK102 6612J00043C UPJ-R1-031 S/T,SCART,SHIELD,SPRING
L1129 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM JK103 6612J10012A UJB-05-02C COMPONENT GR/BL/RD/WH/RD
L1130 6200J000013 MLB-321611-0500P-N2 R/TP 500 OHM JK104 6612J00038B UJB-03-25B 6612J00038A+RED S/W+SHIELD
L114 6200JB8010L MLB-201209-1000L-N2 R/TP 1000OHM 350MA JK1200 6612B00015B DC1R019WDH JAE 0.5MM,19PIN+2PIN,HDMI S/T

- 32 -

Downloaded from www.Manualslib.com manuals search engine

 LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION

JK400 6612J00037A UJB-02-12A UGCOM 2P RCA VERTICAL+SHIELD

JK502 6612F00087A UEJ-CV-032 10MM VERTICAL TYPE+SHIELD
JK600 6612F00087A UEJ-CV-032 10MM VERTICAL TYPE+SHIELD

ACCESSORIES
A1 3828VA0525T MANUAL, USER MF056A 151E TX
A2 6710V00151E REMOTE CONTROLLER, 42PX4R-ZA INPUT
A3 64109EP003A POWER CORD, SP-023+IS-14 I-SHENG
A3 6410TBW001B POWER CORD, SP60+IS14 I-SHENG BSI 1870MM
A4 4972V00178A FIXER, WALL ASSY PDP SET

MISCELLANEOUS
CA1 68509A0002A CABLE,COAXIAL 150MM KCA-NS-0-0053
CA2 6850J00005C CABLE,DVI LVDS UL20276 AWG30 600MM
CA3 6851V00022C CABLE,COAXIAL UL1365#26 VW-1
IC900 692791001AJ SOFT WARE, 3.11V F34B 1024X768
P101 366-922E WAFER, IL-G-6P LGC 2.5mm R/A
PA101 6712000010B REMOTE CONTROLLER RECEIVER, KSM913TC1AR
S1 692791002AF SOFT WARE, 3.03V 7A89 1024X768
TU200 6700MF0012B TUNER, TAFM-W102P SUB
TU201 6700MF0012A TUNER, TAUM-W101P MAIN

- 33 -

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
 PRINTED CIRCUIT BOARD
MAIN (TOP) MAIN (BOTTOM )

SIDE A/V
CONTROL(TOP)

CONTROL(BOTTOM)

INDEX(TOP)

INDEX(BOTTOM)

Downloaded from www.Manualslib.com manuals search engine

 Dec., 2005
P/NO : 38289S0052A Printed in Korea

Downloaded from www.Manualslib.com manuals search engine