Scribd
Upload
176 views3 pages

Aws D1

This document outlines the contents of AWS D1.1/D1.1M: 2020 which provides requirements for welding steel structures. It covers general requirements, design of welded connections, prequalification of welding procedures, qualification of welders and welding operators, and fabrication requirements. Some key areas addressed include allowable stresses for statically and cyclically loaded connections, essential variables for welding procedure and performance qualification, acceptance criteria for testing, preheat and interpass temperature requirements, and fabrication topics such as joint preparation and distortion control.

Uploaded by

Aditya Wicaksono
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
176 views3 pages

Aws D1

This document outlines the contents of AWS D1.1/D1.1M: 2020 which provides requirements for welding steel structures. It covers general requirements, design of welded connections, prequalification of welding procedures, qualification of welders and welding operators, and fabrication requirements. Some key areas addressed include allowable stresses for statically and cyclically loaded connections, essential variables for welding procedure and performance qualification, acceptance criteria for testing, preheat and interpass temperature requirements, and fabrication topics such as joint preparation and distortion control.

Uploaded by

Aditya Wicaksono
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

AWS D1.1/D1.

1M: 2020 Contents


1. General Requirements
 Scope
 Standard Units of Measurement
 Safety Precautions
 Limitations
 Responsibilities
 Approval
 Mandatory and Nonmandatory Provisions
 Welding Symbols
2. Normative References
3. Terms and Definitions
4. Design of Welded Connections
 Scope
Part A – Common Requirements for Design of Welded Connections (Non-tubular and
Tubular Members)
 General
 Contract Plans and Specifications
 Effective Areas
Part B – Specific Requirements for Design of Nontubular Connections (Statically or
Cyclically Loaded)
 General
 Stresses
 Joint Configuration and Details
 Joint Configuration and Details – Groove Welds
 Joint Configuration and Details – Fillet Welded Joints
 Joint Configuration and Details – Plug and Slot Welds
 Filler Plates
 Built-up Members
Part C – Specific Requirements for Design of Nontubular Connections (Cyclically
Loaded)
 General
 Limitations
 Calculation of Stresses
 Allowable Stresses and Stress Ranges
 Detailing, Fabrication, and Erection
 Prohibited Joints and Welds
 Inspection
5. Prequalification of WPSs
 Scope
Part A – WPS Development
 General WPS Requirements
Part B – Base Metal
 Base Metal
Part C – Weld Joints
 Weld Joints
Part D – Welding Processes
 Welding Processes
Part E – Filler Metals and Shielding Gases
 Filler Metal and Shielding Gas
Part F – Preheat and Interpass Temperature Requirements
 Preheat and Interpass Temperature Requirements
Part G – WPS Requirements
 WPS requirements
Part H – Postweld Heat Treatment
 Post-weld Heat Treatment
6. Qualification
 Scope
Part A – General Requirements
 General
 Common Requirements for WPS and Welding Personnel Performance
Qualification
Part B – Welding Procedure Specification (WPS) Qualification
 Production Welding Positions Qualified
 Type of Qualification Tests
 Weld Types for WPS Qualification
 Preparation of WPS
 Essential Variables
 WPS Requirements for Production Welding Using Existing Non-Waveform or
Waveform WPSs
 Methods of Testing and Acceptance Criteria for WPS Qualification
 CJP Groove Welds
 PJP Groove Welds
 Fillet Welds
 Plug and Slot Welds
 Welding Processes Requiring Qualification
Part C – Performance Qualification
 General
 Type of Qualification Tests Required
 Weld Types for Welder and Welding Operator Performance Qualification
 Preparation of Performance Qualification Forms
 Essential Variables
 CJP Groove Welds for Nontubular Connections
 Extent of Qualification
 Methods of Testing and Acceptance Criteria for Welder and Welding Operator
Qualification
 Method of Testing and Acceptance Criteria for Tack Welder Qualification
 Retest
Part D – Requirements for CVN Toughness Testing
 General: CVN Testing
 CVN Tests
 Combining FCAW-S with Other Welding Processes in a Single Joint
 Reporting
7. Fabrication
 Scope
 Base Metal
 Welding Consumables and Electrode Requirements
 ESW and EGW Processes
 WPS Variables
 Preheat and Interpass Temperatures
 Heat Input Control for Quenched and Tempered Steels
 Stress-Relief Heat Treatment
 Backing
 Welding and Cutting Equipment
 Welding Environment
 Conformance with Design
 Minimum Fillet Weld Sizes
 Preparation of Base Metal
 Reentrant Corners
 Weld Access Holes, Beam Copes, and Connection Material
 Tack Welds and Construction Aid Welds
 Camber in Built-up Members
 Splices
 Control of Distortion and Shrinkage
 Tolerance of Joint Dimensions
 Dimensional Tolerance of Welded Structural Members
 Weld Profiles
 Technique for Plug and Slot Welds
 Repairs
 Peening
 Caulking
 Arc Strikes
 Weld Cleaning
 Weld Tabs

You might also like