Amplitude Modulation
Amplitude Modulation
UNIT I
AMPLITUDE MODULATION
Amplitude Modulation- DSBSC, DSBFC, SSB, VSB - Modulation index, Spectra, Power
relations and Bandwidth
AM Generation – Square law and switching modulator,
DSBSC Generation –Balanced and Ring Modulator,
SSB Generation – Filter, Phase Shift and Third Methods,
VSB Generation – Filter Method, Hilbert Transform, Pre-envelope & complex envelope –
comparison of different AM techniques, super heterodyne Receiver
1.1 Introduction
The purpose of a communication system is to transmit information-bearing signals
through a communication channel separating the transmitter from the receiver.
Information bearing signals are also referred to as baseband signals. The term baseband is used
to designate the band of frequencies representing the original signal as delivered by a source of
information.
The proper use of the communication channel requires a shift of the range of baseband
frequencies into other frequency ranges suitable for transmission, and a corresponding shift
back to the original frequency range after reception.
A shift of the range of frequencies in a signal is accomplished by using modulation,
which is defined as the process by which some characteristic of a carrier is varied in
accordance with a modulating wave (signal).
A common form of the carrier is a sinusoidal wave, in which case we speak of a
Continuous-wave modulation process. The baseband signal is referred to as the modulating
wave, and the result of the modulation process is referred to as the modulated wave.
Modulation is performed at the transmitting end of the communication system.
At the receiving end of the system, we usually require the original baseband signal to be
restored.
This is accomplished by using a process known as demodulation, which is the reverse
of the modulation process.
In basic signal-processing terms, we thus find that the transmitter of an analog
communication system consists of a modulator and the receiver consists of a demodulator, as
depicted in Figure 1.1.
In addition to the signal received from the transmitter, the receiver input includes
channel noise. The degradation in receiver performance due to channel noise is determined by
the type of modulation used.
In angle modulation, the angle of the sinusoidal carrier wave is varied in accordance
with the baseband signal.
Figure 2.2 displays the waveforms of amplitude-modulated and angle modulated
signals for the case of sinusoidal modulation.
Parts (a) and (b) of the figure show the sinusoidal carrier and modulating waves, respectively.
Parts (c) and (d) show the corresponding amplitude-modulated and frequency-modulated
waves, respectively. Frequency modulation is a form of angle modulation.
Where kais a constant called the amplitude sensitivity of the modulator responsible for
the generation of the modulated signal s(t).Typically, carrier Ac and message signal m(t)
measured in volts, in which case the ka is measured in volt-1.
Figure 1.3 shows a baseband signal m(t), and Figures 1.3b and 1.3c show the
corresponding AM wave s(t) for two values of amplitude sensitivity ka and a carrier amplitude
AC = 1 volt.
We observe that the envelope of s(t) has essentially the same shape as the baseband
signal m(t) provided that two requirements are satisfied:
2. The carrier frequency fc is much greater than the highest frequency component W of the
message signal m(t), that is fc>>W. We call W the message bandwidth. If the condition of
Equation is not satisfied, an envelope cannot be visualized (and therefore detected)
satisfactorily.
EC8491 COMMUNICATION THEORY 4
UNIT I
From Equation (1.2), we find that the Fourier transform of the AM wave S(f) is given by
……………………..(1.3)
Suppose that the baseband signal m(t) is band-limited to the interval -W ≤ f ≤W, as in
Figure 1.4. The shape of the spectrum shown in this figure is intended for the purpose of
illustration only.
We find from Equation (1.3) that the spectrum S(f) of the AM wave is as shown in Figure 1.4
for the case when fc> W. This spectrum consists of two delta functions weighted by the factor
AC/2 and occurring at ± fc and two versions of the baseband spectrum translated in frequency
by ± fc and scaled in amplitude by kaAc/2.
1. As a result of the modulation process, the spectrum of the message signal s(t) for negative
frequencies extending from -W to 0 becomes completely visible for positive(i.e., measurable)
frequencies, provided that the carrier frequency satisfies the condition fc > W; herein lies the
importance of the idea of “negative” frequencies.
2. For positive frequencies, the portion of the spectrum of an AM wave lying above the carrier
frequency fc is referred to as the upper sideband, whereas the symmetric portion below fc is
referred to as the lower sideband.
For negative frequencies, the upper sideband is represented by the portion of the spectrum
below -fc and the lower sideband by the portion above -fc. The condition fc> W ensures that
the sidebands do not overlap.
Mathematical representation of AM wave
It must be noted that the phase angle remains constant in this process. Thus it can be ignored.
The amplitude of the carrier wave varies at fm.
Vmax = Vm +VcandVmin=Vc - Vm
From above equation ,we find Vm ,Vc
1.3 AM Generation
AM wave generation is done by two methods namely, the square law
modulator and switching modulator, both of which require the use of nonlinear element
for their implementation.
EC8491 COMMUNICATION THEORY 6
UNIT I
Square-Law Modulator
A square-law modulator requires three features:
A means of summing the carrier and modulating waves, a nonlinear element, and a band-pass
filter for extracted the desired modulation products.
These features of the modulator are illustrated in Fig 1.6.
Semiconductor diodes and transistor are the most common nonlinear devices used for
implementing square-law modulators. The filtering requirement is usually satisfied by using a
single- or double-tuned filter.
When a nonlinear element such as a diode suitably biased and operated in a restricted portion
of its characteristic curve, that is ,signal applied to the diode is relatively weak.
The first term in Eq. (3) is the desired AM signal with ka = 2a2/a1. The remaining three terms
are unwanted terms that are removed by filtering.
Let the modulating wave m(t) be limited to the band -W < f < W, as in Fig. 1(a).
Then, from Eq. (3) we find that the amplitude spectrum |V2 (f)| is as shown in Fig. 1(b).
It follows therefore that the unwanted terms may be removed from V2(t) by designing
the tuned filter at the modulator output of Fig. to have a mid-band frequency fc and bandwidth
2W, which satisfy the requirement that fc > 3W.
EC8491 COMMUNICATION THEORY 7
UNIT I
SWITCHING MODULATOR
Amplitude modulation is accomplished using a nonlinear device, the combined sum of
the message signal and carrier wave is applied to a diode, with the carrier amplitude being large
enough to swing across the characteristic curve of the diode.
Fourier analysis of the voltage developed across a resistive load reveals the generation of an
AM component, which may be extracted by means of a band-pass filter.
We assume that the diode acts as an ideal switch, that is,
it presents zero impedance when it is forward-biased [corresponding to c(t)> 0] and
infinite impedance when it is reverse-biased [corresponding to c(t) <0].
We may thus approximate the transfer characteristic of the diode load resistor combination by a
piecewise-linear characteristic, as shown in Fig1.7.
Figure 1.7 Switching modulator. (a)Circuit diagram. (b) Idealized input-output relation.
That is, the load voltage V2(t) varies periodically between the values V1(t) and zero at a rate
equal to the carrier frequency fc.
In this way, by assuming a modulating wave that is weak compared with the carrier wave, we
have effectively replaced the nonlinear behaviour of the diode by an approximately equivalent
piecewise-linear time-varying operation.
We may express Eq. (2) mathematically as
Where is a periodic pulse train of duty cycle equal to one-half, and period To = 1/fc, as in
Fig. 1.7 representing this by its Fourier series, we have
Therefore, substituting Eq. (4) in (3), we find that the load voltage V2(t) consists of the sum of
two components:
1.The component
Which is the desired AM wave with amplitude sensitivity Ka = 4//πAc. The switching
modulator is therefore made more sensitive by reducing the carrier amplitude Ac.
However, it must be maintained large enough to make the diode act like an ideal switch.
EC8491 COMMUNICATION THEORY 8
UNIT I
2. Unwanted components, the spectrum of which contains delta functions at 0, +2fc, +4fc, and
soon, and which occupy frequency intervals of width 2W centred at 0, +3fc. +5fc, and so on,
Where W is the message bandwidth.
The unwanted terms are removed from the load voltage V2(t) by means of a band-pass filter
with mid-band frequency fc and bandwidth 2W, provided that fc > 2W.
This latter condition ensures that the frequency separations between the desired AM wave the
unwanted components are large enough for the band-pass filter to suppress the unwanted
components.
DEMODULATION OF AM WAVE'S
The process of demodulation provides a means of recovering from an incoming modulated
wave an output that is proportional to the original modulating wave.
In effect, demodulation is the reverse of modulation. We will describe two devices for the
demodulation of AM waves, namely, the square-law detector and envelope detector.
Square-Law Detector
A square-law detector is essentially obtained by a square-law modulator for the purpose of
demodulation. ConsiderV2 (t) defining the transfer characteristic of a nonlinear device, which
is reproduced here for convenience:
Where V1 (t) and V2 (t) are the input and output voltages, respectively, and a1 and a2are
constants. When such a device is used for the demodulation of an AM wave,
we have for the input
The desired signal, namely , is due to the - hence, the name "square-law
detection".
This component can be extracted by means of a low-pass filter. This is not the only
contribution within the baseband spectrum, because the term will give rise to a
Plurality of similar frequency components. The ratio of wanted signal to distortion is
To make this ratio large we limit the percentage modulation, that is, | kam(t)| should be kept
small compared with unity for all t.
EC8491 COMMUNICATION THEORY 9
UNIT I
Envelope Detector
Consider the case of a narrow-band AM wave, that is, one in which the carrier frequency is
large compared with the message bandwidth, and for which the percentage modulation is less
than 100 percent.
Then the desired demodulation can be accomplished by using a simple, yet highly effective
device known as envelope detector.
Ideally, an envelope detector produces an output signal that follows the envelope of the input
signal waveform exactly. Some version of this circuit is used in almost all commercial AM
radio receivers.
An envelope detector of the series type is shown in Fig., which consists of a-diode and a
resistor-capacitor filter. The operation of this envelope detector is as follows.
Figure (1.8)Envelope detector. (a) Circuit diagram. (b) AM wave input(c)Envelope detector
output.
On the positive half-cycle of the Input signal, the diode is forward-biased and the capacitor C
charges up rapidly to the peak value of the input signal. When the input signal falls below this
value, the diode becomes reverse-biased and the capacitor C discharges slowly through the
road resistor Rl·
The discharging process continues until the next positive half-cycle. When the input signal
becomes greater than the voltage across the capacitor, the diode conducts again and the process
is repeated.
We assume that the diode is ideal. Presenting zero impedance to current flow in the forward-
biased region, and infinite impedance in the reverse-biased region.
We further assume that the AM wave applied to the envelope detector is supplied by a voltage
source of internal impedance Rs.
The charging time constant R, C must be short compared with the carrier period 1/fc that is,
EC8491 COMMUNICATION THEORY 10
UNIT I
So that the capacitor C charges rapidly and thereby follows the applied voltage up to the
positive peak when the diode is conducting.
The result is that the capacitor voltage or detector output is very nearly the same as the
envelope of the AM wave, as illustrated in Fig1.8(c).
Amplitude modulation defined in Equation (1.2) suffers from two major limitations:
1. Amplitude modulation is wasteful of power. The carrier wave c(t) is completely
Independent of the information-bearing signal m(t). The transmission of the carrier wave
therefore represents a waste of power, which means that in amplitude modulation only a
fraction of the total transmitted power is actually affected by m(t).
2. Amplitude modulation is wasteful of bandwidth, the upper and lower sidebands of an AM
wave are uniquely related to each other by virtue of their symmetry about the carrier frequency;
hence, given the magnitude and phase spectra of either sideband, we can uniquely determine
the other. In this observation, amplitude modulation is wasteful of band width as it requires a
transmission bandwidth equal to twice the message bandwidth.
To overcome these limitations, we must make certain modifications: suppress the carrier and
modify the sidebands of the AM wave. These modifications naturally result in increased
system complexity.
The carrier wave c(t) is completely independent of the information- carrying signal or
baseband signal m(t), which means that the transmission of the carrier wave represents a waste
of power.
This point to a shortcoming of amplitude modulation, namely, that only a fraction of the total
transmitted power is affected by m(t); To overcome this shortcoming, we may suppress the
carrier component from the modulated wave, resulting in double-sideband suppressed carrier
modulation(DSBSC) .
Thus, by suppressing the carrier we obtain a modulated wave that is proportional to the product
of the carrier wave and the baseband signal.
EC8491 COMMUNICATION THEORY 11
UNIT I
( )= [ − + ( + )]…………….(1.12)
For the case when the baseband signal m (t) is limited to the interval -W < f<W, as in
Fig.1.ll(a),we thus find that the spectrum S(f) of the DSBSC wave s(t)is as illustrated in part (b)
of the figure.
BALANCEDMODULATOR
One possible scheme for generating a DSB-SC wave is to use two AM modulators
arranged in a balanced configuration so as to suppress the carrier wave, as shown in the block
diagram of Fig.1.12.
We assume that the two AM modulators are identical, except for the sign reversal of the
modulating wave applied to the input of one of the modulators. Thus the outputs of the two
AM modulators may be expressed as follows:
( )= [ + ( )] ( )……(1.12)
And
( )= [ − ( )] ( )……(1.13)
RING MODULATOR
One of the most useful product modulator that is well-suited for generating aDSBSC
wave is the ring modulator shown in Fig. 1.13(a).
EC8491 COMMUNICATION THEORY 13
UNIT I
The four diodes form a ring in which they all point in the same way-hence, the name. The
diodes are controlled by a square-wave carrier c(t) of frequency fc, which is applied by means
of two center-tapped transformers. We assume that the diodes are ideal and the transformers
are perfectly balanced.
When the carrier supply is positive, the outer diodes are switched on, presenting zero
impedance, whereas the inner diodes are switched off, presenting infinite impedance, as in Fig.
1.13(b), so that the modulator multiplies the baseband signal m(t) by+1.
When the carrier supply is negative, the situation becomes reversed as in Fig 1.13c and the
modulator multiplies the baseband signal by -1. Thus the ring modulator.
In its ideal form, is a product modulator or a square wave carrier and the baseband signal, as
illustrated in fig 1.14.For the case of a sinusoidal modulating signal.
……….(1.15)
EC8491 COMMUNICATION THEORY 14
UNIT I
……… (1.16)
We see that there is no output from the modulator at the carrier frequency; that is the modulator
output consists entirely of modulation products. Thus the ring modulator is referred to us
Double balanced modulator. Because, it is balanced with respect to the baseband signal as well
as the square-wave carrier.
The baseband signal m(t) can be uniquely recovered from a DSB-SC wave s(t) by first
Multiplying s(t) with a locally generated sinusoidal wave and then low-pass filtering the
Product, as in Figure 1.15.
It is assumed that the local oscillator signal is exactly coherent or synchronized, in both
frequency and phase, with the carrier wave c(t) used in the product modulator to generate s(t).
This method of demodulation is known as coherent detection or synchronous demodulation.
It is instructive to derive coherent detection as a special case of the more general demodulation
process using a local oscillator signal of the same frequency but arbitrary phase difference ɸ,
measured with respect to the carrier wave c(t).
Thus, denoting the local oscillator signal by ′ ( + ɸ), and using Equation (1.11) for the
DSB-SC wave s(t),we find that the product modulator output in Figure 1.15 is
……(1.17)
The first term in Equation (1.17) represents a DSB-SC modulated signal with a carrier
frequency 2fc, whereas the second term is proportional to the baseband signal m(t).
This is further illustrated by the spectrum V(f) shown in Figure, 1.16, where it is assumed that
the baseband signal m(t) is limited to the interval -W < f < W.
EC8491 COMMUNICATION THEORY 15
UNIT I
Figure 1.16 illustrating the spectrum of a product modulator output with a DSB-SC modulated
wave as input.
It is therefore apparent that the first term in Equation (1.17) is removed by the low-pass filter in
Figure 1.15,
Provided that the cut-off frequency of this filter is greater than W but less than 2f - W.
This requirement is satisfied by choosing fc> W. At the filter output we then obtain a signal
given by
……..(1.18)
The demodulated signal V0(t) is therefore proportional to m(t) when the phase error ɸ is a
constant.
The amplitude of this demodulated signal is maximum when ɸ = 0, and it is minimum (zero)
when ɸ = ±π/2. The zero demodulated signal, which occurs for ɸ= ±π/2, represents the
quadrature null effect of the coherent detector.
Thus the phase error ɸ in the local oscillator causes the detector output to be attenuated by a
factor equal to cosɸ. As long as the phase error ɸ is constant, the detector provides an
undistorted version of the original baseband signal m(t).
The precise frequency-domain description of an SSB wave depends on which side band is
transmitted. Consider a baseband signal m(t) with a spectrum M(f)that is limited to the band
-W < f <W as in Fig. 1.17 (a).
The one of the DSBSC wave obtained by multiplying m(t) by the carrier wave ( ) is
as shown in Fig. 1.17(b).
The upper sideband is represented in duplicate by the frequencies above fc, and those below -fc:
and when only the upper sideband is transmitted, the resulting SSB wave s(t) has the spectrum
shown in Fig.1.17(c)
Likewise, the lower sideband is represented in duplicate by the frequencies below, (for positive
frequencies) and those above -fc, (for negative frequencies); and when only the lower sideband
is transmitted, the spectrum of the corresponding SSB wave is as shown in Fig. 1.17(d).
EC8491 COMMUNICATION THEORY 16
UNIT I
Thus the essential function of an SSB modulation system is to translate the spectrum of the
modulating wave. Either with or without inversion, to a new location in the frequency domain;
and the transmission bandwidth requirement of the system is one-half that of an AM or DSBSC
modulation system.
The benefit of using SSB modulation is therefore derived principally from the reduced
bandwidth requirement and the elimination of the high-power carrier wave. The principal
disadvantage of the SSB modulation system is its cost and complexity.
To describe an SSB wave in the time domain, we may use the representation developed in a
band-pass signal. According to this representation,
( )= () ( )- ( ) ( )
Where ( )the in-phase component of the SSB is wave, and ( ) is its quadrature component.
The in-phase Component, except for a scaling factor, may be derived from ( ) by first
multiplying ( )by ( ) and then passing the product through a low-pass filter.
Similarly, the quadrature component, ( )except for a scaling factor, may be derived from
( )by first multiplying ( )by ( ) and then passing the product through an identical
low-pass identical filter.
We thus find that the Fourier transforms of ( )and ( ) are related to that of the SSB wave
S(f) as follows, respectively
EC8491 COMMUNICATION THEORY 17
UNIT I
Where -W<f <W defines the frequency band occupied by the message signal m(t). Consider
now the case of an SSB wave that is obtained by transmitting only the upper sideband. The
spectrum of such a modulated wave is shown in Fig.1.17(c).
Specifically, given a Fourier transformable message signal m(t) with its Hilbert transform
denoted by ( ),the SSB modulated wave produced by is defined by
………….. (1.19)
Where ( )is the carrier, ( ) is its -90° phase-shifted version; the plus
and minus signs apply to the lower SSB and upper SSB, respectively.
We may develop two methods for generating SSB-modulated waves, namely called
the frequency discrimination method and the Phase discrimination method, as described next.
These two methods are based on the frequency-domain and time-domain descriptions of the
SSB wave, respectively.
Frequency Discrimination Method
One straightforward method for SSB generation, called the frequency discrimination method, is
depicted in Fig. 1.18.The SSB modulator is consists of two components: product modulator
followed by band-pass filter.
The product modulator produces a DSB-SC modulated wave with an upper sideband and a
lower sideband.
The band-pass filter is designed to transmit one of these two sidebands, depending on whether
the upper SSB or lower SSB is the desired modulation.
For the design of the band-pass filter to be practically feasible, there must be a certain
separation between the two sidebands that is wide enough to accommodate the transition band
of the band-pass filter.
From a practical viewpoint the most severe requirement of SSB generation using the frequency
discrimination method arises from the unwanted sideband.
The nearest frequency component of the unwanted sideband is separated from the desired
sideband by twice the lowest frequency component of the message (modulating) signal.
The implication here is that for the generation of an SSB modulated signal to be possible, the
message spectrum must have an energy gap cantered at the origin, as illustrated in Figure 1.19.
This requirement is naturally satisfied by voice signals, whose energy gap is about 600 Hz
wide (i.e.,it extends from -300 to +300 Hz). Thus, assuming that the upper sideband is
retained,the spectrum of the SSB modulated signal is as shown in Figure 1.19b.
EC8491 COMMUNICATION THEORY 18
UNIT I
Figure 1.19 (a) Spectrum of a message signal m(t) with an energy gap of width 2f a, centred on the
origin. (b) Spectrum of corresponding SSB signal containing the upper sideband.
In designing the band-pass filter used in the frequency-discriminator for generating a SSB-
modulated wave, we must meet the three basic requirements:
1. The desired sideband lies inside the pass band of the filter.
2. The unwanted sideband lies inside the stop band of the filter.
3. The filter’s transition band, which separates the pass band from the stop band, is twice the
lowest frequency component of the message signal.
This kind of frequency discrimination usually requires the use of highly selective filters, which
can only be realized in practice by means of crystal resonators.
However, the one functional block in Fig. 1.20 that requires special attention is the wide-band
phase-shifter, which is designed to produce the Hilbert transform in response to the incoming
message signal.
The role of the quadrature path embodying the wide-band phase shifter is merely to interfere
with the in-phase path. So as to eliminate power in one of the two sidebands, depending on
whether upper SSB or lower SSB is the requirement.
EC8491 COMMUNICATION THEORY 19
UNIT I
The two modulators of Figs. 1.18 and 1.20 are clearly quite different in their structures.
In terms of design challenge, the band-pass filter in the frequency discriminator of Fig. 1.18
stands out as the functional block that requires special attention.
On the other hand, in the phase discriminator of Fig. 1.20, it is the wide-band phase shifter that
requires special attention.
This method of demodulation assumes perfect synchronism between the oscillator in the
coherent detector and the oscillator used to supply the carrier wave in the transmitter.
This requirement is usually met in one of two ways:
1.A low-power pilot carrier is transmitted in addition to the selected sideband.
2. A highly stable oscillator, tuned to the same frequency as the carrier frequency, is
used in the receiver.
In the latter method, it is inevitable that there would be some phase error ɸ in the local
Oscillator output with respect to the carrier wave used to generate the incoming SSB
modulated wave.
1.6 VESTIGIAL-SIDEBAND AM
........... (1.20)
Where h(t) is the impulse response of the VSB filter. In the frequency domain, the
corresponding expression is
........... (1.21)
To determine the frequency-response characteristics of the filter, we will consider the
demodulations of the VSB signal u(t). We multiply u(t) by the carrier component ( )
and pass the result through an ideal low pass filter, as shown in Figure 1.22.
Thus, the product signal is v(t) = u(t) cos(2π fc) t, or equivalently,
........ (1.22)
If we substitute U(f) from Equation (1.21) into Equation (1.22), we obtain
........ (1.23)
The low pass filter rejects the double-frequency terms and passes only the components in
the frequency range .
Hence, the signal spectrum at the output of the ideal low pass filter is
......... (1.24)
The message signal at the output of the low pass filter must be undistorted. Hence, the VSB
filter characteristic must satisfy the condition
......... (1.25)
This condition is satisfied by a filter that has the frequency-response characteristics shown
in Figure 1.23.
We note that H (f) selects the upper sideband and a vestige of the lower sideband.
It has odd symmetry about the carrier frequency fc in the frequency range fc - fa < f <
fc + fa, where fa is a conveniently selected frequency that is some small fraction of W,
i.e., fa « W. Thus, we obtain an undistorted version of the transmitted signal. Figure1.24
illustrates the frequency response of a VSB filter that selects the lower sideband and a vestige
of the upper sideband.
EC8491 COMMUNICATION THEORY 21
UNIT I
Figure 1.24 Frequency response of the VSB filter for selecting the lower sideband of the
message signals.
In practice, the VSB filter is designed to have some specified phase characteristics.
To avoid distortion of the message signal, the VSB filter should have a linear phase over
its pass band .
In applications such as a TV broadcast, a large carrier component is transmitted along with the
message in the VSB signal. In such a case, it is possible to recover the message by passing the
received VSB signal through an envelope detector.
To be more specific, the role of the quadrature component (if present) is merely to interfere
with the in-phase component, so as to reduce or eliminate power in one of the sidebands
of the modulated signal s(t), depending on how the quadrature component is defined.
The super heterodyne receiver, or superhet as it is often referred to, is a special type of receiver
that fulfils all three functions, particularly the first two, in an elegant and practical fashion.
Specifically, it overcomes the difficulty of having to build a tuneable highly selective and
variable filter. Indeed, practically all radio and TV receivers now being made are of the super
heterodyne type.
Basically, the receiver consists of a radio-frequency (RF) section, a mixer and local oscillator,
an intermediate-frequency (IF) section, demodulator, and power amplifier. Typical frequency
parameters of commercial AM and FM radio receivers are listed in Table 1.2.
EC8491 COMMUNICATION THEORY 23
UNIT I
Figure 1.26 shows the block diagram of a super heterodyne receiver for amplitude modulation
using an envelope detector for demodulation.
The incoming amplitude-modulated wave is picked up by the receiving antenna and amplified
in the RF section that is tuned to the carrier frequency of the incoming wave.
The combination of mixer and local oscillator (of adjustable frequency) provides a
heterodyning function, whereby the incoming signal is converted to a predetermined fixed
intermediate frequency, usually lower than the incoming carrier frequency.
Where fLO is the frequency of the local oscillator and fRF is the carrier frequency of the
incoming RF signal.
We refer to fIF as the intermediate frequency (IF), because the signal is neither at the original
input frequency nor at the final baseband frequency.
The mixer local oscillator combination is sometimes referred to as the first detector, in which
case the demodulator is called the second detector.
The IF section consists of one or more stages of tuned amplification, with a bandwidth
corresponding to that required for the particular type of modulation that the receiver is intended
to handle.
The IF section provides most of the amplification and selectivity in the receiver.
The output of the IF section is applied to a demodulator, the purpose of which is to recover the
baseband signal.
If coherent detection is used, then a coherent signal source must be provided in the receiver.
The final operation in the receiver is the power amplification of the recovered message signal.
In a super heterodyne receiver the mixer will develop an intermediate frequency output
when the input signal frequency is greater or less than the local oscillator frequency by an
amount equal to the intermediate frequency.
EC8491 COMMUNICATION THEORY 24
UNIT I
That is, there are two input frequencies, namely,| fLO ± fRF |, which will result in fIF at the
mixer output. This introduces the possibility of simultaneous reception of two signals differing
in frequency by twice the intermediate frequency.
Since the function of the mixer is to produce the difference between two applied frequencies, it
is incapable of distinguishing between the desired signal and its image in that it produces an IF
output from either one of them.
The only practical cure for image interference is to employ highly selective stages in the
RF section (i.e., between the antenna and the mixer) in order to favour the desired signal
and discriminate against the undesired or image signal.
The effectiveness of suppressing unwanted image signals increases as the number of selective
stages in the RF section increases, and as the ratio of intermediate to signal frequency
increases.
The basic difference between AM and FM super heterodyne receivers lies in the use of an FM
demodulator such as limiter-frequency discriminator.
In an FM system, the message information is transmitted by variations of the instantaneous
frequency of a sinusoidal carrier wave, and its amplitude is maintained constant.
Therefore, any variations of the carrier amplitude at the receiver input must result from noise or
interference.
An amplitude limiter, following the IF section, is used to remove amplitude variations by
clipping the modulated wave at the IF section output almost to the zero axis.
The resulting rectangular wave is rounded off by a band-pass filter that suppresses harmonics
of the carrier frequency. Thus the filter output is again sinusoidal, with amplitude that is
practically independent of the carrier amplitude at the receiver input