ORDER NO.

CRT4227
DEH-2100UB/XS/EW5

CD RDS RECEIVER

DEH-2100UB /XS/EW5

DEH-2120UB/XS/EW5
DEH-2110UB/XS/UR
This service manual should be used together with the following manual(s):
Model No. Order No. Mech.Module Remarks

CX-3240 CRT4050 S10.5COMP2-iPod/USB CD Mech. Module : Circuit Descriptions, Mech. Descriptions, Disassembly

For details, refer to "Important Check Points for Good Servicing".

PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan

PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2008
K-ZZZ. OCT. 2008 Printed in Japan
 1 2 3 4

SAFETY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
A
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safety
repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safety, you should not risk trying to do so
and refer the repair to a qualified service technician.

Where in a manufacturer’s service documentation, for example in circuit diagrams or lists

of components, a symbol is used to indicate that a specific component shall be replaced only
by the component specified in that documentation for safety reasons, the following symbol shall
be used:

- Safety Precautions for those who Service this Unit.

When checking or adjusting the emitting power of the laser diode exercise caution in order to get safe, reliable
results.

Caution:
1. During repair or tests, minimum distance of 13 cm from the focus lens must be kept.
2. During repair or tests, do not view laser beam for 10 seconds or longer.

CAUTION:
C
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

CAUTION
CLASS 1M INVISIBLE LASER RADIATION WHEN OPEN. DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS

WARNING!
The AEL (accessible emission level) of the laser power output is less than CLASS 1
D but the laser component is capable of emitting radiation exceeding the limit for
CLASS 1.
A specially instructed person should do servicing operation of the apparatus.

Laser diode characteristics

Wave length : 785 nm to 814 nm
Maximum output : 1 190 µW(Emitting period : unlimited)

E
Additional Laser Caution
Transistors Q101 in PCB drive the laser diodes.
When Q101 is shorted between their terminals, the laser diodes will radiate beam.
If the top cover is removed with no disc loaded while such short-circuit is continued,
the naked eyes may be exposed to the laser beam.

DEH-2100UB/XS/EW5
2
1 2 3 4
 5 6 7 8

[Important Check Points for Good Servicing]

In this manual, procedures that must be performed during repairs are marked with the below symbol.
Please be sure to confirm and follow these procedures.
A
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by
following the safety instructions described in this manual.

1 Use specified parts for repair.

Use genuine parts. Be sure to use important parts for safety.

2 Do not perform modifications without proper instructions.

Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.

3 Make sure the soldering of repaired locations is properly performed. B

When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)

4 Make sure the screws are tightly fastened.

Please be sure that all screws are fastened, and that there are no loose screws.

5 Make sure each connectors are correctly inserted.

Please be sure that all connectors are inserted, and that there are no imperfect insertion.

6 Make sure the wiring cables are set to their original state.

Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc. C

7 Make sure screws and soldering scraps do not remain inside the product.

Please check that neither solder debris nor screws remain inside the product.

8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.

Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.

9 There should be no spark traces or similar marks on the power plug.

When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.

a Safe environment should be secured during servicing. D

When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.

2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.

3. Lubricants, Glues, and Replacement parts

Use grease and adhesives that are equal to the specified substance.
Make sure the proper amount is applied.
E

4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.

5. Shipping mode and Shipping screws

To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be
installed before shipment. Please be sure to follow this method especially if it is specified in this manual.

DEH-2100UB/XS/EW5
5 6 7 8
3
 1 2 3 4

CONTENTS
SAFETY INFORMATION ..................................................................................................................................... 2
1. SERVICE PRECAUTIONS ............................................................................................................................... 5
A
1.1 SERVICE PRECAUTIONS......................................................................................................................... 5
1.2 NOTES ON SOLDERING .......................................................................................................................... 5
2. SPECIFICATIONS ............................................................................................................................................ 6
2.1 SPECIFICATIONS...................................................................................................................................... 6
2.2 DISC/CONTENT FORMAT ........................................................................................................................ 8
2.3 PANEL FACILITIES .................................................................................................................................... 9
2.4 CONNECTION DIAGRAM ....................................................................................................................... 12
3. BASIC ITEMS FOR SERVICE........................................................................................................................ 13
3.1 CHECK POINTS AFTER SERVICING..................................................................................................... 13
3.2 PCB LOCATIONS .................................................................................................................................... 14
3.3 JIGS LIST ................................................................................................................................................ 15
3.4 CLEANING............................................................................................................................................... 15
B 4. BLOCK DIAGRAM.......................................................................................................................................... 16
5. DIAGNOSIS.................................................................................................................................................... 19
5.1 OPERATIONAL FLOWCHART ................................................................................................................ 19
5.2 ERROR CODE LIST ................................................................................................................................ 20
5.3 CONNECTOR FUNCTION DESCRIPTION ............................................................................................. 22
6. SERVICE MODE ............................................................................................................................................ 23
6.1 DISPLAY TEST MODE ............................................................................................................................ 23
6.2 CD TEST MODE ...................................................................................................................................... 24
7. DISASSEMBLY............................................................................................................................................... 25
8. EACH SETTING AND ADJUSTMENT ........................................................................................................... 28
8.1 CD ADJUSTMENT................................................................................................................................... 28
8.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT.................................................... 29
C
9. EXPLODED VIEWS AND PARTS LIST.......................................................................................................... 32
9.1 PACKING ................................................................................................................................................. 32
9.2 EXTERIOR (1) ......................................................................................................................................... 34
9.3 EXTERIOR (2) ......................................................................................................................................... 36
9.4 CD MECHANISM MODULE..................................................................................................................... 38
10. SCHEMATIC DIAGRAM ............................................................................................................................... 40
10.1 TUNER AMP UNIT(GUIDE PAGE) ........................................................................................................ 40
10.2 KEYBOARD UNIT.................................................................................................................................. 46
10.3 CD MECHANISM MODULE(GUIDE PAGE) .......................................................................................... 48
10.4 WAVEFORMS ........................................................................................................................................ 54
11. PCB CONNECTION DIAGRAM ................................................................................................................... 58
D 11.1 TUNER AMP UNIT................................................................................................................................. 58
11.2 KEYBOARD UNIT.................................................................................................................................. 62
11.3 CD CORE UNIT(S10.5COMP2-USB-C3) .............................................................................................. 64
12. ELECTRICAL PARTS LIST .......................................................................................................................... 66

DEH-2100UB/XS/EW5
4
1 2 3 4
 5 6 7 8

1. SERVICE PRECAUTIONS
1.1 SERVICE PRECAUTIONS
A

1. You should conform to the regulations governing

the product (safety, radio and noise, and other
regulations), and should keep the safety during
servicing by following the safety instructions
described in this manual.
2. Before disassembling the unit, be sure to turn off
the power. Unplugging and plugging the connectors
during power-on mode may damage the ICs inside
the unit.
3. To protect the pickup unit from electrostatic discharge B
during servicing, take an appropriate treatment
(shorting-solder) by referring to "the DISASSEMBLY".
4. After replacing the pickup unit, be sure to check the
grating.
5. Be careful in handling ICs. Some ICs such as MOS
type are so fragile that they can be damaged by
electrostatic induction.

1.2 NOTES ON SOLDERING

D

For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit.
Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs
accompanied by reworking of soldering.

Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 C.
Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 C in general, although
the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of
the soldering iron.

Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting
temperatures (hard to melt/easy to harden). E

The following lead-free solders are available as service parts:

Parts numbers of lead-free solder:
GYP1006 1.0 in dia.
GYP1007 0.6 in dia.
GYP1008 0.3 in dia.

DEH-2100UB/XS/EW5
5 6 7 8
5
 1 2 3 4

2. SPECIFICATIONS
2.1 SPECIFICATIONS
A

DEH-2100UB/XS/EW5, DEH-2120UB/XS/EW5

General Maximum amount of memory

Power source..........................14.4 V DC (10.8 V to 15.1 V .............................................. 250 GB
allowable) Minimum amount of memory
Grounding system.................Negative type .............................................. 256 MB
Max. current consumption USB Class.............................. MSC (Mass Storage Class)
...............................................10.0 A File system............................. FAT16, FAT32
B Backup current ......................... 2 mA or less MP3 decoding format ......... MPEG-1 & 2 Audio Layer 3
WMA decoding format ....... Ver. 7, 7.1, 8, 9, 10, 11 (2ch
Dimensions (W × H × D): audio)
DIN (Windows Media Player)
Chassis .................. 178 mm × 50 mm × 165 WAV signal format ............... Linear PCM & MS ADPCM
mm (Non-compressed)
Nose ....................... 188 mm × 58 mm × 15 mm
D FM tuner
Chassis .................. 178 mm × 50 mm × 165 Frequency range................... 87.5 MHz to 108.0 MHz
mm Usable sensitivity.................. 11 dBf (0.7 μV/75 , mono,
Nose ....................... 170 mm × 48 mm × 15 mm S/N: 30 dB)
Weight ..................................... 1.3 kg Signal-to-noise ratio............. 72 dB (IEC-A network)
C

Audio MW tuner
Maximum power output ...... 50 W × 4 Frequency range................... 531 kHz to 1 602 kHz
Continuous power output .. 22 W × 4 (50 Hz to 15 000 Usable sensitivity.................. 25 μV (S/N: 20 dB)
Hz, 5% THD, 4 load, both Signal-to-noise ratio............. 62 dB (IEC-A network)
channels driven)
Load impedance ................... 4 (4 to 8 allowable) LW tuner
Preout max output level ...... 2.0 V Frequency range................... 153 kHz to 281 kHz
Tone controls: Usable sensitivity.................. 28 μV (S/N: 20 dB)
Bass Signal-to-noise ratio............. 62 dB (IEC-A network)
Frequency............. 100 Hz
D Gain ........................ ±13 dB Note
Mid
Frequency.............. 1 kHz Specifications and the design are subject to mod-
Gain ......................... ±12 dB ifications without notice due to improvements.
Treble
Frequency.............. 10 kHz
Gain ......................... ±12 dB

CD player
System ..................................... Compact disc audio system
Usable discs .......................... Compact disc
Signal-to-noise ratio............. 94 dB (1 kHz) (IEC-A net-
E
work)
Number of channels ............ 2 (stereo)
MP3 decoding format ......... MPEG-1 & 2 Audio Layer 3
WMA decoding format ....... Ver. 7, 7.1, 8, 9, 10, 11 (2ch
audio)
(Windows Media Player)
WAV signal format ................ Linear PCM & MS ADPCM
(Non-compressed)

USB
Specification ......................... USB 2.0 full speed
F Supply current ..................... 500 mA

DEH-2100UB/XS/EW5
6
1 2 3 4
 5 6 7 8

2.3 PANEL FACILITIES

What ’s what 8 (detach) button A

Press to remove the front panel from the
Head unit head unit.
3 9 AUX input jack (3.5 mm stereo jack)
12 45 6 7
Use to connect an auxiliary device.

a 1 to 6 buttons
Press for preset tuning. Also used for con-
trolling functions.
• 1/S.Rtrvcan be used to control S.RTRV
B
(sound retriever).
• 2/PAUSE can be used to control PAUSE
dc b a 98 (pause).
1 SRC/OFF button • 5/ can be used to control RANDOM
This unit is turned on by selecting a source. (random).
Press to cycle through all the available • 6/ can be used to control REPEAT(re-
sources. peat).

2 /LIST button b / / / buttons

Press to display the disc title list, track title Press to perform manual seek tuning, fast
C
list, folder list or file list. forward, reverse and track search controls.
Also used for controlling functions.
3 MULTI-CONTROL • When operating menus
Turn to increase or decrease the volume. — Pressing is the same function as
Also used for controlling functions. turning MULTI-CONTROL right.
— Pressing is the same function as
4 TA/AF button turning MULTI-CONTROL left.
Press to turn TA function on or off. Press — Pressing is the same function as
and hold to turn AF function on or off. pressing DISP/BACK/SCRL .
5 Disc loading slot — Pressing and holding is the same D
Insert a disc to play. function as pressing and holding
DISP/BACK/SCRL .
6 (eject) button — Pressing is the same function as
Press to eject a disc. pressing MULTI-CONTROL .
— Pressing and holding is the same
7 USB port function as pressing and holding
Use to connect a USB audio player/USB MULTI-CONTROL .
memory. • When operating lists
• When connecting, open up the USB con- — Pressing is the same function as
nector lid. turning MULTI-CONTROL left. E
• Use a USB cable to connect the USB — Pressing is the same function as
audio player/USB memory to the USB turning MULTI-CONTROL right.
port. Since the USB audio player/USB — Pressing is the same function as
memory is projected forward from the pressing DISP/BACK/SCRL .
unit, it is dangerous to connect directly.
Pioneer CD-U50E USB cable is also avail-
able. For details, consult your dealer.

DEH-2100UB/XS/EW5
5 6 7 8
9
 1 2 3 4

— Pressing and holding is the same Program service name, PTY information
function as pressing and holding and other literal information are dis-
A
DISP/BACK/SCRL . played.
— Pressing is the same function as • Built-in CD player and USB
pressing MULTI-CONTROL . Elapsed playback time and literal infor-
— Pressing and holding is the same mation are displayed.
function as pressing and holding
MULTI-CONTROL . 4 (song) indicator
Appears when the track (song) name is dis-
c DISP/BACK/SCRL button played on the main display section.
Press to select different displays. Also, appears when a playable audio file is
Press and hold to scroll through the text in- selected while operating the list.
B
formation.
Press to return to the previous display when 5 indicator
operating the menu. Appears when an upper tier of folder or
Press and hold to return to the main menu menu exists.
when operating the menu.
6 (folder) indicator
d BAND/ESC button Appears when operating list function.
Press to select among three FM bands and
7 indicator
MW/LW bands.
Appears when a lower tier of folder or menu
Press to return to the ordinary display when
C exists.
operating the menu.
8 LOC indicator
Appears when local seek tuning is on.
Display indication
9 LOUD (loudness) indicator
12 3
Appears when loudness is on.

a (TA) indicator
Appears when TA (traffic announcement
standby) function is on.
D 57 9 a b c def g
468 b (TP) indicator
Appears when a TP station is tuned in.
1 (disc) indicator
Appears when the disc (album) name is dis- c (AF) indicator
played on the main display section. Appears when AF (alternative frequencies
search) function is on.
2 (artist) indicator
Appears when the disc (track) artist name is d (stereo) indicator
displayed on the main display section. Appears when the selected frequency is
being broadcast in stereo.
E 3 Main display section
Displays band, frequency, elapsed playback e (repeat) indicator
time and other settings. Shows when track repeat is turned on.
• Tuner Also, shows when folder repeat is on.
Band and frequency are displayed.
• RDS

DEH-2100UB/XS/EW5
10
1 2 3 4
 5 6 7 8

f (random) indicator
Shows when random play is on.
A
g (Sound Retriever) indicator
Appears when Sound Retriever function is
on.

Fastening the front panel

If you do not plan to detach the front panel,
the front panel can be fastened with supplied
screw. B

Screw
BPZ20P060FTC

DEH-2100UB/XS/EW5
5 6 7 8
11
 F
E
B
A

D
C

12
1
1

6. Note
Depending on the kind of vehicle, 5. This product
the function of 3* and 5* may be
different. In this case, be sure to 1. Rear output
connect 2* to 5* and 4* to 3*. 22. Power amp
(sold separately)
1* 20.To Rear output
2. Antenna jack
3* 2* 3. Fuse (10 A)
21. Connect with RCA cables
(sold separately)
4. Wired remote input
Hard-wired remote control
5* 4* adaptor can be connected
(sold separately).
7. Connect leads of the
same color to each other.

2
2

2.4 CONNECTION DIAGRAM

8. Cap (1*)
Do not remove cap
if this terminal is
not in use.

23. System remote control

9. Yellow (3*) 10. Yellow (2*) 16. Blue/white
Back-up (or Connect to the constant Connect to system control terminal of the
accessory) 12 V supply terminal. power amp (max. 300 mA 12 V DC). 24. Left 25. Right

11. Red (5*) 12. Red (4*)

DEH-2100UB/XS/EW5
Accessory Connect to terminal controlled by 17. Blue/white (7*) 26.Rear speaker 26.Rear speaker
(or back-up) ignition switch (12 V DC). Connect to auto-antenna relay control
terminal (max. 300 mA 12 V DC).

3
3

27. Perform these connections when

13. Black (chassis ground) 18. Blue/white (6*) using the optional amplifier.
Connect to a clean, paint-free metal location. The pin position of the ISO connector will
differ depends on the type of vehicle.
Connect 6* and 7* when Pin 5 is an
antenna control type. In another type of
vehicle, never connect 6* and 7*.

14. ISO connector 19. Speaker leads

Note White: Front left
In some vehicles, the ISO connector 15. Yellow/black White/black: Front left
may be divided into two. In this case, If you use an equipment with Mute Gray: Front right
be sure to connect to both connectors. function, wire this lead to the Audio Gray/black: Front right
Mute lead on that equipment. If not, Green: Rear left
keep the Audio Mute lead free of any Green/black: Rear left

4
connections.
4

Violet: Rear right

Violet/black: Rear right
 5 6 7 8

3. BASIC ITEMS FOR SERVICE

3.1 CHECK POINTS AFTER SERVICING
A
To keep the product quality after servicing, please confirm following check points.

No. Procedures Item to be confirmed

1 Confirm whether the customer complain has The customer complain must not be
been solved. reappeared.
If the customer complain occurs with the Display, audio and operations must be
specific media, use it for the operation check. normal.
2 CD Play back a CD. No malfunction on display, audio and
(Track search) operation.
3 FM/AM tuner Check FM/AM tuner action. Display, audio and operations must be
(Seek, Preset) normal. B
Switch band to check both FM and AM.
4 Check whether no disc is inside the product. The media used for the operating check must
be ejected.
5 Appearance check No scratches or dirt on its appearance after
receiving it for service.

See the table below for the items to be checked regarding audio:

Item to be checked regarding audio

Distortion
Noise
C
Volume too low
Volume too high
Volume fluctuating
Sound interrupted

DEH-2100UB/XS/EW5
5 6 7 8
13
 1 2 3 4

3.2 PCB LOCATIONS

C CD Core Unit (S10.5COMP2-USB-C3)

B

A Tuner Amp Unit

C
B Keyboard Unit

A:DEH-2100UB/XS/EW5
B:DEH-2120UB/XS/EW5
C:DEH-2110UB/XS/UR
Unit Number : YWM5292(A)
Unit Number : YWM5317(B)
Unit Number : YWM5316(C)
Unit Name : Tuner Amp Unit
Unit Number :
D Unit Name : Keyboard Unit
Unit Number : CWX3679
Unit Name : CD Core Unit(S10.5COMP2-USB-C3)

DEH-2100UB/XS/EW5
14
1 2 3 4
 5 6 7 8

3.3 JIGS LIST

- Jigs List A
Name Jig No. Remarks
Test Disc TCD-782 Checking the grating
L.P.F. Checking the grating (Two pieces)

- Grease List
Name Grease No. Remarks B
Grease GEM1024 CD Mechanism Module
Grease GEM1045 CD Mechanism Module

3.4 CLEANING
C

Before shipping out the product, be sure to clean the

following portions by using the prescribed cleaning
tools:
Portions to be cleaned Cleaning tools
CD pickup lenses Cleaning liquid : GEM1004
Cleaning paper : GED-008

DEH-2100UB/XS/EW5
5 6 7 8
15
 1 2 3 4

4. BLOCK DIAGRAM

A
A TUNER AMP UNIT
SYS+B SWVDD3V
ANTENNA CN401

LDET
REFB
REFA

CE1
1

IFB
IFA

CE2
DO
CK
DI
SL-IN

SLOUT
2

1 ANT 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

IFOUTA

SLOUT
CE1
RFGND1

RFGND2

RFGND3

RFGND4

VDD

DO
IFOUTB

CE2
LDET
VCC

DI
DGND

REFINA

REFINB
ANT

CK
SLIN
IC2
EEPROM SL-IN
IFA
IFB
REFA
REFB
LDET
B DI
CK
CE1
DO
VCO LFP CE2
SLOUT

ATT
ATT TANK

IC1
MIX / IF / PLL

ATT RF LFP

ELECTRON
CF SOURCE

C
FM/AM TUNER UNIT
TUNL
2
IN2_L

IC
PM
CD-Lch
1
IN1_L

VCK, VDT, VST

REGULATOR IC
IC911
BA49181-V12 SYSTEM
1 47 COMPU
VDDCONT PWROFF
2 36 IC601(
5
SW5V SW5V BESNS BSENS PN502
D SWVDD3V
6
SWVDD SYSPW
3 15
SYSPW
7 1
SYS+B SYS+B SW5VCONT 4 SWVDD
8
VDD3V VDD +B 10 B.UP

C CD CORE UNIT(S10.5COMP2-USB-C3) +B.UP

9

SWVDD3V
PICKUP UNIT RF AMP, CD DECODER, MP3&WMA DECODER
(P10.5)(SERVICE) DIGITAL SERVO/DATA•PROCESSOR Q601
85 DREG
CPU, USB HOST CONTROLLER
VDD2
LD CN101
LD- 9
15 15 141 M-REGC
Q101 LD
USBXTAL 1 55
PLL_VDD
MD 142 X205
5 5 PD 57
REFO 48MHz DVDD3
VREF 8 133
8 REFOUT /USBXTAL 2 94
DVDD2
AC,BD,E,F 121
HOLOGRAM
UNIT XTAL 50 DVDD4

FOM FOM X201 IC501

3 3 ACTUATOR/ 16.93MHz USB5V BD9007F
FOP FOP /XTAL 52
MD
FOCUS ACT. 2 2 MOTOR DRIVER B.UP
1
TOP PVin
TRACKING ACT. 1 1 TOP Q102
TOM 8 5 25
4 4
TOM IC301 VCC VDD2 Vin EN SYNC
LD+
14 14
BA5839FP TD,FD 1 2
E 12
FOM 39 CN701 CN651 IC251 VIN SW
11
FOP SD,MD /PUEN BD6538G 3 28
14 55 LOUT LOUT EN USBCTL
TOP LOUT 13 7 4 27
13 5 FLG FLG
TOM IC201 USB5V VOUT
VDD
SPINDLE
M PE5666A VDD VDD
MOTOR VDD2 9 11 VDD3V
16 22 Q991
SOP LOEJ 28
LOEJ VD VD CD VD
15 VD 2 18 B.UP
SOM 21 20
18
LOADING/CARRIAGE LCOP CLCONT CLCONT
1 19
Q992
MOTOR M 17
CONT
9 41
LCOM CONT 5

126
VDCONT
8
12EJ
7
8EJ
10 16 /RESET RESET 16
DSCSNS /RESET 8 12 CDRST
9
HOME
BRST,BRXEN,BSRQ BRST,BRXEN,BSRQ,BDATA,BSCK
S904 S905 S901
12EJ 8EJ HOME BDATA,BSCK

5 DP 16 USBZ
S903 DP 4
DSCSNS 4 DM USBF
DM 17 3
F VD

VDSENS 11

DEH-2100UB/XS/EW5
16
1 2 3 4
 5 6 7 8

SYSTEM MICRO
COMPUTER
IC601(1/2)
PN5024B CN871
142 KEYAD
KEYAD 2 WIRED
130 KEYD
KEYD 3 REMOTE
A B
SL-IN 62
SL
IFA 77 IF_INA
CN351
IFB 78 IF_INB RL 2 RCA OUT
REFA 96
FREFA
REFB 97 FREFB Q351
LDET 99 LOCK
DI 100
TUNDO
B
CK 101 TUNCK
CE1 102
CE
DO 103
TUNDI
CE2 109
CE2
SLOUT 136
SL CN911

ASENSE B.UP
B.UP 1
Q931
59 35 ASENS ACC
L_OUT ASENS 3

GND
2

ELECTRONIC VOLUME/
SOURCE SELECTOR POWER
CONNECTOR
21 FL+
FL+ 12
TUNL Rear_L
7 12
RLIn FL− 23 FL− C
2 10
IN2_L 5 RL+
RL+ 11
6 14 AMP
Front_L FLIn 3 RL−
IC151 RL− 9
IC301
PML014A PAL007C
CD-Lch 22 25 BREM
1 4 AUX-L MUTE B.REM 6
IN1_L IN4+_L
5 AUX-G 6
IN4-_L VCC B.UP
4
STBY VCC 20
TELIN
8
VCK, VDT, VST

MUTE
Q201(2/2)
A :DEH-2100UB/XS/EW5
B :DEH-2120UB/XS/EW5
SYSTEM MICRO C :DEH-2110UB/XS/UR
47 COMPUTER MUTE
PWROFF
36 IC601(2/2) Q201(1/2)
BSENS PN5024B 44
15
SYSPW
MUTE D
1 TEL IN
SWVDD Q851
B.UP 26
TELIN

A B
VDD3V
82
85 XOUT
DREG X601

9
M-REGC
XIN
81 74.1MHz
B KEYBOARD UNIT
55
PLL_VDD CN1802
57 52 CN831 CN1801 AUX R 3
DVDD3 BU_X1
94 X602 AUX-L AUX L AUX L 2 FRONT
DVDD2 7 7
51 4.7186MHz AUX-G AUX G AUX G 1 AUX
121 6
DVDD4 BU_X2 6
C KEY MATRIX
F SW5V 3 3 SW5V S1803
S1833 S1801 S1834 S1805 S1807 S1809
111 ROT1 ROT1 1 4 KST1 BAND/ESC CD EJECT 3 2 1
5 25 SYNC ROT1 16 16
110 ROT0 ROT0 2 5 KDT2
ROT0 17 17
S1811 S1813 S1815 S1817 S1819 E
3 TA/ →RF
28 →
ILLUMI 4 5 6 DISP/BACK
USBCTL
27 D1824-D1832
FLG ILMPW D1834-D1840
S1825 S1827 S1829 S1831
Q821 S1823 S1826 S1828 S1830 S1832
ILM+B ILM+B
B.UP 15 15 LIST DOWN RIGH UP LEFT

B.UP LCDBK
D1823
2 Q822
ILMPW
KDT0-3

KST0-4

126
VDCONT
SW5V
SOURCE
S1802
16 33 SOURCE SOURCE
CDRST SRC 4 4 REM KEY DATA 23
X1
X1801
24 KYDT KYDT 20 5.00MHz
KYDT 18 18 KYDT LCD DRIVER/ 22
KEY CONTROLLER X0

DPDT
23 DPDT
19 19
DPDT 18
DPDT IC1801
10
PD6340A
VLCD LCD1801
56
34 DSENSE DSEN VDD
DSENS 20 20 F
CN1803
USB5V VBUS VBUS VBUS
14 14 1
USBZ D+ D+ D+
12 12 3 USB
USBF D- D- D-
13 13 2

DEH-2100UB/XS/EW5
5 6 7 8
17
 1 2 3 4

LCD (CAW1970)
A

E
SEGMENT

COMMON

DEH-2100UB/XS/EW5
18
1 2 3 4
 5 6 7 8

5. DIAGNOSIS
5.1 OPERATIONAL FLOWCHART
A
Power ON

VDD = 3.3 V
Pin 8

BSENS
Pin 36
BSENS = L B

ASENS
Pin 35

ASENS = L

Starts
communication
with Grille
microcomputer.

C
300 ms
SWVDD <- H
Pin 1
300 ms
In case of the above signal, the communication
Source keys
with Grille microcomputer may fail.
operative
If the time interval is not 300 msec, the oscillator
may be defective.

Source ON

SYSPW <- H
Pin 15

Completes power-on operation.

(After that, proceed to each source operation)

DEH-2100UB/XS/EW5
5 6 7 8
19
 1 2 3 4

5.2 ERROR CODE LIST

- Error Messages
A If a CD is not operative or stopped during operation due to an error, the error mode is turned on and cause(s) of
the error is indicated with a corresponding number. This arrangement is intended at reducing nonsense calls from
the users and also for facilitating trouble analysis and repair work in servicing.

(1) Basic Indication Method

1) When SERRORM is selected for the CSMOD (CD mode area for the system), error codes are written to DMIN
(minutes display area) and DSEC (seconds display area). The same data is written to DMIN and DSEC. DTNO
remains in blank as before.

2) Head unit display examples

B
Depending on display capability of LCD used, display will vary as shown below. xx contains the error number.

8-digit display 6-digit display 4-digit display

ERROR-xx ERR-xx E-xx

(2) Error Code List

Code Class Displayed error code Description of the code and potential cause(s)
10 Electricity Carriage Home NG CRG can't be moved to inner diameter.
SERVO LSI Com- CRG can't be moved from inner diameter.
C munication Error -> Failure on home switch or CRG move mechanism.
Communication error between microcomputer and SERVO LSI.
11 Electricity Focus Servo NG Focusing not available.
-> Stains on rear side of disc or excessive vibrations on REWRITABLE.
12 Electricity Spindle Lock NG Spindle not locked. Sub-code is strange (not readable).
Subcode NG -> Failure on spindle, stains or damages on disc, or excessive vibrations.
A disc not containing CD-R data is found.
Turned over disc are found, though rarely.
CD signal error.
17 Electricity Setup NG AGC protection doesn't work. Focus can be easily lost.
D
-> Damages or stains on disc, or excessive vibrations on REWRITABLE.
30 Electricity Search Time Out Failed to reach target address.
-> CRG tracking error or damages on disc.
44 Electricity ALL Skip Skip setting for all track.
(CD-R/RW)
50 Mechanism CD On Mech Error Mechanical error during CD ON.
-> Defective loading motor, mechanical lock and mechanical sensor.
A0 System Power Supply NG Power (VD) is ground faulted.
-> Failure on SW transistor or power supply (failure on connector).
E Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors).
Unreadable TOC does not constitute an error. An intended operation continues in this case.
Upper digits of an error code are subdivided as shown below:
1x: Setup relevant errors, 3x: Search relevant errors, Ax: Other errors.

DEH-2100UB/XS/EW5
20
1 2 3 4
5 6 7 8

DEH-2100UB/XS/EW5
5 6 7 8
21
 1 2 3 4

5.3 CONNECTOR FUNCTION DESCRIPTION

REAR
A
OUTPUT

ANTENNA WIRED REMOTE

CONTROL
(2100, 2120) 16 14 12 10 8 6 4 2

15 13 11 9 7 5 3 1

16 FR+ 8 MUTE
C 15 RR+ 7 NC
14 FR- 6 B.REM
13 RR- 5 NC
12 FL+ 4 A.ANT
11 RL+ 3 ACC
10 FL- 2 GND
9 RL- 1 B.UP

DEH-2100UB/XS/EW5
22
1 2 3 4
 5 6 7 8

6. SERVICE MODE
6.1 DISPLAY TEST MODE
A

1. To enter the test mode

Turn on ACC and Backup while pressing the 1 and the 3 buttons together.

2. To exit from the test mode

Turn off the ACC and Backup.

3. Operation method
B
Change display as follows by pressing the 1 and the 3 buttons together.

System version display

ROM Correction version display

Normal display

Display stop

All lighting of display

C

All lights out of display

LCD check mode 1

LCD check mode 2

LCD check mode 3

LCD check mode 1 D

LCD check mode 2

LCD check mode 3

DEH-2100UB/XS/EW5
5 6 7 8
23
 1 2 3 4

6.2 CD TEST MODE

- Flow Chart
[Key] [4] + [6] + Reset or
[4] + [6] + BU + ACC
A Contents Test Mode In

Display

[CD] or [SOURCE]
Source On

TRK MIN SEC

[BAND] [3] [2] [4]

Power On Power On RF AMP *1 SPINDLE *9
(T.Offset is adjusted) (T.Offset is not adjusted) Gain switching Speed switching
TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC
00 00 00 99 99 99 GG GG GG SP SP SP

B [BAND] [3] [6] [1] [>] [<] [2]

[5]
Power Off Focus Close Focus Mode switching Tracking Servo CRG + CRG - Self-adjusting
Gop Mode *10
S curve check *2 Close *8 *8 switching *3
Gop Mode switching
TRK MIN SEC TRK MIN SEC TRK MIN SEC 00 00 00 00 00 00 00 00 00 TRK MIN SEC
TRK MIN SEC
91 91 91 0X 0X 0X or 99 99 99 or 99 99 99 or 99 99 99 ?? ?? ??
OL OL OL

[BAND] [1] [6] [3] [>] [<] [2]

Power Off T.Close & AGC T.Close RF AGC / CRG + CRG - T.Balance adjustment /
Applicable servomechanism Applicable servomechanism RF AGC coefficient display T.BAL coefficient display
TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC 8X 8X 8X 8X 8X 8X TRK MIN SEC
?tr ?min ?sec ?tr ?min ?sec ?? ?? ?? or 9X 9X 9X or 9X 9X 9X ?? ?? ??

[BAND] [1] [3] [6] [>] [<] [2]

Power Off F,T,RF AGC*7 F,T AGC / F.Bias CRG/TR jump CRG/TR Jump + CRG/TR Jump - Tracking Open
F.Bias display switching RF AGC value switching*5 *4 *4
TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC 8X 8X 8X
C ?? ?? ?? ?tr ?min ?sec ?tr ?min ?sec ?tr ?min ?sec ?tr ?min ?sec or 9X 9X 9X

*6

[BAND] [2]
Power Off Tracking Open

TRK MIN SEC 8X 8X 8X

or 9X 9X 9X

*1) TYP -> + 6 dB -> + 12 dB Operation

TRK MIN SEC TRK
06MIN06SEC06 TRK
12MIN12SEC12 [Key] Test Mode
[BAND] Power On/Off
[>] CRG + / TR Jump +
*2) Focus Close -> S.Curve -> F EQ measurement setting (Direction of the external surface)
TRK
D 00MIN00SEC00 TRK
01MIN01SEC01 TRK
02MIN02SEC02 [<] CRG - / TR Jump -
(TRK99MIN99SEC99) (Direction of the internal surface)
[1] T. CLS & AGC & Applicable servomechanism /
AGC,AGC display setting
*3) F.Offset Display -> RF.Offset -> T.Offset Display -> Switch to the [2] RF Gain switching / Offset adjustment display /
order of the original display
T.Balance adjustment / T. Open
[3] F. Close,S Curve / Rough Servo and RF AGC /
*4) 1TR/4TR/10TR/32TR/100TR F,T,RF AGC
*5) Single -> 4TR -> 10TR -> 32TR -> 100TR -> CRG Move [4] SPDL 1X/2X switching
9x(8x):91(81) 92(82) 93(83) 94(84) 95(85) 96(86) As for the double speed(2x), audio output cannot be
supported.
*6) Only at the time of CRG move, 100TR jump [5] Error Rate measurement
ON : ERR 30 Counts Start
E BER display data[%]
*7) TRK/MIN/SEC -> F.AGC -> T.AGC Gain -> F Bias -> RF AGC
[6] F. Mode switching / Tracking Close / CRG•TR
Jump Switching
*8) CRG motor voltage = 2 [V]

*9) TYP (1X) -> 2X -> 1X *10) OFF(TYP) -> FORCUS -> TRACKING
TRK MIN SEC TRK
22MIN22SEC22 TRK
11MIN11SEC11 TRK MIN SEC TRK
70MIN70SEC70 TRK
71MIN71SEC71

• As for the double speed (2x), audio output cannot be supported

• After the [Eject] key is pressed keys other than the [Eject] key should not be pressed, until disc ejection is complete.
• When the key [2] or [3] is pressed during the Focus Search, the power supply should be immediately turned off (otherwise the lens
F sticks to Wall, causing the actuator to be damaged).
• In the case of TR jump other than to 100TR, the function shall continue to be processed even if the TR jump key is released. As for
the CRG Move and 100TR Jump, the mechanism shall be set to the Tracking Close mode when the key is released.
• When the power is turned on/off the jump mode is reset to the Single TR (91) while the gain of the RFAMP is reset to 0 dB. At the
same time all the self-adjusting values shall return to the default setting.
DEH-2100UB/XS/EW5
24
1 2 3 4
 5 6 7 8

7. DISASSEMBLY
- Removing the Case (not shown)
A
1. Remove the Case.

- Removing the CD Mechanism Module (Fig.1) CD Mechanism Module

1 Release the two latches and then remove the

Panel Assy.
2

2 Remove the four screws.

2 B

Disconnect the connector and then remove the

CD Mechanism Module.

2 2

1 1
2

Panel Assy

Fig.1

- Removing the Tuner Amp Unit (Fig.2)

1 Remove the two screws.

D

Remove the three screws. 1 1

2

3 Remove the two screws.

4 Straighten the tabs at two locations

indicated and then remove the Tuner
Amp Unit.
2
E
2
3

3
2

4 4

Tuner Amp Unit F

Fig.2

DEH-2100UB/XS/EW5
5 6 7 8
25
 1 2 3 4

- How to hold the Mechanism Unit

1. Hold the Upper and Lower Frames.
2. Do not hold the front portion of the Upper
A Frame, because it is not very solid.

Do not squeeze this area.

- Removing the Upper and Lower Frames

1. With a disc inserted and clamped in the
mechanism, remove the two Springs (A),
the six Springs (B), and the four Screws.
2. Turn the Upper Frame using the part "a" as
C a pivot, and remove the Upper Frame.
3. While lifting the Carriage Mechanism, a
remove it from the three Dampers. B Upper Frame
Caution: When assembling, be sure to apply B
some alcohol to the Dampers and assemble
the mechanism in a clamped state.

B
B

Damper
A
Carriage Mechanism
E
Damper
Lower Frame

DEH-2100UB/XS/EW5
26
1 2 3 4
 5 6 7 8

- How to remove the CD Core Unit

1. Apply Shorting Solder to the flexible cable of
the Pickup, and disconnect it from the Shorting Solder
connector. A
2. Unsolder the four leads, and loosen the
Screw.
3. Remove the CD Core Unit.
Caution: When assembling the CD Core Unit,
assemble it with the SW in a clamped state
so as not to damage it.

Screw
B

CD Core Unit

Solder

- How to remove the Pickup Unit

1. Make the system in the carriage mechanism mode, and have it clamped.
2. Remove the CD Core Unit and remove the leads from the Inner Holder.
3. Remove the Poly Washer, Change Arm, and Pickup Lock Arm. C

4. While releasing from the hook of the Inner Holder, lift the end of the Feed Screw.
Caution: When assembling, move the Planet Gear to the load/eject position before setting the Feed Screw in the Inner
Holder.
Assemble the sub unit side of the Pickup, taking the plate (Chassis) in-between. When treating the leads of the Load
Carriage Motor Assy, do not make them loose over the Feed Screw.

Poly Washer
Change Arm

Inner Holder
Pickup Lock Arm
D

Feed Screw

Planet Gear

Pickup Rack E

Chassis

Pickup F

DEH-2100UB/XS/EW5
5 6 7 8
27
 1 2 3 4

8. EACH SETTING AND ADJUSTMENT

8.1 CD ADJUSTMENT
A

1) Cautions on adjustments 2) Test mode

In this product the single voltage (3.3 V) is used for the This mode is used to adjust the CD mechanism module.
regulator. The reference voltage is the REFO1 (1.65 V) To enter the test mode.
instead of the GND. While pressing the 4 and 6 keys at the same time, reset.
If you should mistakenly short the REFO1 with the GND To exit from the test mode.
during adjustment, accurate voltage will not be obtained, Turn off the ACC and back up.
and the servo’s misoperation will apply excessive shock
to the pickup. To avoid such problems: Notes:
a. Do not mix up the REFO1 with the GND when a. During ejection, do not press any other keys than the
connecting the (-) probe of measuring instruments. EJECT key until the loaded disc is ejected.
B Especially on an oscilloscope, avoid connecting the (-) b. If you have pressed the (->) key or (<-) key during focus
probe for CH1 to the GND. search, turn off the power immediately to protect the
b. In many cases, measuring instruments have the same actuator from damage caused by the lens stuck.
potential as that for the (-) probe. Be sure to set the c. For the TR jump modes except 100TR, the track jump
measuring instruments to the floating state. operation will continue even if the key is released.
c. If you have mistakenly connected the REFO1 to the GND, d. For the CRG move and 100TR jump modes, the tracking
turn off the regulator or the power immediately. loop will be closed at the same time when the key is
released.
Before mounting and removing filters or leads for e. When the power is turned off and on, the jump mode
adjustment, be sure to turn off the regulator. is reset to the single TR (91), the RF amp gain is set to 0 dB,
and the auto-adjustment values are reset to the default
For stable circuit operation, keep the mechanism settings.
C operating for about one minute or more after the
regulator is turned on.

In the test mode, any software protections will not

work. Avoid applying any mechanical or electrical
shock to the mechanism during adjustment.

The RFI and RFO signals with a wide frequency range

are easy to oscillate. When observing the signals,
insert a resistor of 1k ohms in series.

The load and eject operation is not guarantied with the

D mechanism upside down. If the mechanism is blocked
due to mistaken eject operation, reset the product or
turn off and on the ACC to restore it.

DEH-2100UB/XS/EW5
28
1 2 3 4
 5 6 7 8

8.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT

Note :
The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism
module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU
unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if the
PU unit must be changed, the grating should be checked using the procedure below.

Purpose :
To check that the grating is within an acceptable range when the PU unit is changed.

Symptoms of Mal-adjustment : B
If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform
track search operations, or taking a long time for track searching.

Method :
Measuring Equipment Oscilloscope, Two L.P.F.
Measuring Points E, F, REFO1
Disc TCD-782
Mode TEST MODE

CD CORE UNIT
C
REFO1

E F L.P.F.

Xch Ych
E 100 kohm
Oscilloscope
VREF 390 pF

F 100 kohm

VREF 390 pF

L.P.F. D

Checking Procedure
1. In test mode, load the disc and switch the 3 V regulator on.
2. Using the -> and <- buttons, move the PU unit to the innermost track.
3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance
adjustment the display should now read "81". Press key 3. The display will change, returning to "81" on the
fourth press.
4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase E
difference is within 75 degrees. Refer to the photographs supplied to determine the phase angle.
5. If the phase difference is determined to be greater than 75 degrees try changing the PU unit to see if there is any
improvement. If, after trying this a number of times, the grating angle does not become less than 75 degrees then the
mechanism should be judged to be at fault.
Note
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be
seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the
average angle.
Hint
Reloading the disc changes the clamp position and may decrease the "wobble".

DEH-2100UB/XS/EW5
5 6 7 8
29
 1 2 3 4

Grating waveform Ech -> Xch 20 mV/div, AC

Fch -> Ych 20 mV/div, AC
A

0 degrees 30 degrees

45 degrees 60 degrees

75 degrees 90 degrees

DEH-2100UB/XS/EW5
30
1 2 3 4
5 6 7 8

DEH-2100UB/XS/EW5
5 6 7 8
31
 1 2 3 4

9. EXPLODED VIEWS AND PARTS LIST

NOTES : Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List.
The > mark found on some component parts indicates the importance of the safety factor of the part.
A
Therefore, when replacing, be sure to use parts of identical designation.
"
Screw adjacent to mark on the product are used for disassembly.
For the applying amount of lubricants or glue, follow the instructions in this manual.
(In the case of no amount instructions,apply as you think it appropriate.)
9.1 PACKING

DEH-2100UB/XS/EW5
32
1 2 3 4
 5 6 7 8

(1) PACKING SECTION PARTS LIST

Mark No. Description Part No. Mark No. Description Part No.

1 Cord Assy See Contrast table (2) 12 Bush CNV3930

2 Polyethylene Bag CEG-162 13 Unit Box See Contrast table (2)
A
* 3 Accessory Assy YEA5070 14 Contain Box See Contrast table (2)
4 Screw BPZ20P060FTC 15 Protector YHP5050
5 Screw Assy CEA3849
16 Protector YHP5051
6 Screw CBA1650 17 Case Assy YXB5009
* 7 Polyethylene Bag CEG-127 18-1 Owner's Manual See Contrast table (2)
8 Screw CRZ50P090FTC 18-2 Owner's Manual See Contrast table (2)
9 Screw TRZ50P080FTC * 18-3 Warranty Card See Contrast table (2)
10 Polyethylene Bag CEG1160
18-4 Installation Manual See Contrast table (2)
11 Handle CND3707 B

(2) CONTRAST TABLE

DEH-2100UB/XS/EW5, DEH-2120UB/XS/EW5 and DEH-2110UB/XS/UR are constructed the same except for the
following:
Mark No. Description DEH-2100UB/XS/EW5 DEH-2120UB/XS/EW5 DEH-2110UB/XS/UR
1 Cord Assy CDP1015 CDP1015 CDP1016
13 Unit Box YHG5449 YHG5450 YHG5452
14 Contain Box YHL5449 YHL5450 YHL5452
18-1 Owner's Manual YRD5217 YRD5217 YRB5097
18-2 Owner's Manual YRD5218 YRD5218 Not used C

* 18-3 Warranty Card CRY1279 CRY1279 YRY5003

18-4 Installation Manual YRD5219 YRD5219 Not used
Owner's Manual,Installation Manual
Part No. Language

YRD5217 English, Spanish(Espanol), German, French

YRD5218 Italian, Dutch, Russian

YRD5219 English, Spanish(Espanol), German, French, Italian, Dutch, Russian

YRB5097 Russian D

DEH-2100UB/XS/EW5
5 6 7 8
33
 1 2 3 4

9.2 EXTERIOR (1)

DEH-2100UB/XS/EW5
34
1 2 3 4
 5 6 7 8

(1) EXTERIOR (1) SECTION PARTS LIST

Mark No. Description Part No. Mark No. Description Part No.

1 Screw BSZ25P060FTB 21 Holder CND3466

2 Screw BSZ26P060FTC 22 Terminal(CN402) VNF1084
A
3 Screw BSZ26P100FTC 23 Terminal(CN601) VNF1084
4 Screw BSZ26P160FTC 24 Terminal(CN801) VNF1084
5 Holder CND4748 > 25 Fuse(10 A) YEK5001

6 CD Mechanism Module(S10.5) CXK5778 26 Holder See Contrast table (2)

7 Screw ISS26P055FTC 27 Holder YND5034
8 Cable YDE5043 28 Heat Sink YNR5123
9 Tuner Amp Unit See Contrast table (2) 29 Chassis Unit See Contrast table (2)
10 Screw BPZ26P080FTC 30 Button CAC4836

11 Screw BSZ26P060FTC 31 Spring CBH2367 B

12 Screw BSZ26P200FTC 32 Spring(Black) CBH2962
13 Pin Jack(CN351) CKB1056 33 Spring(Silver) CBH2961
14 Plug(CN911) CKM1376 34 Cover CNN1665
15 Connector(CN651) CKS3833 35 Panel CNS9662

16 Connector(CN871) See Contrast table (2) 36 Arm CNW1439

17 Connector(CN831) CKS6050 37 Arm CNV9312
18 Antenna Jack(CN401) CKX1070 38 IC(IC301) PAL007C
19 Holder CND3706 39 IC(IC911) BA49181-V12
20 FM/AM Tuner Unit See Contrast table (2) 40 Transistor(Q991) 2SD2396
C

(2) CONTRAST TABLE

DEH-2100UB/XS/EW5, DEH-2120UB/XS/EW5 and DEH-2110UB/XS/UR are constructed the same except for the
following:
Mark No. Description DEH-2100UB/XS/EW5 DEH-2120UB/XS/EW5 DEH-2110UB/XS/UR
9 Tuner Amp Unit YWM5292 YWM5317 YWM5316
16 Connector(CN871) CKS4124 CKS4124 Not used
20 FM/AM Tuner Unit CWE2106 CWE2106 CWE2123
26 Holder YND5025 YND5025 YND5026
29 Chassis Unit YXA5539 YXA5540 YXA5541 D

DEH-2100UB/XS/EW5
5 6 7 8
35
 1 2 3 4

9.3 EXTERIOR (2)

DEH-2100UB/XS/EW5
36
1 2 3 4
 5 6 7 8

(1) EXTERIOR (2) SECTION PARTS LIST

Mark No. Description Part No. Mark No. Description Part No.

1 Cord Assy See Contrast table (2) 16 Cover YNS5405

2 Terminal Cover CKX-003 17 Grip(USB) YNV5176
A
3 Holder CND3598 18 LCD(LCD1801) CAW1970
4 Case YNB5046 19 Connector(CN1801) CKS6049
5 Panel YNS5406 20 •••••

6 Detachable Assy See Contrast table (2) 21 Jack(CN1802) YKN5001

7 Screw BPZ20P100FTC 22 Connector(CN1803) YKS5032
8 Spring CBH2210 23 Holder YNC5061
9 Button(EJECT) YAC5341 24 Rubber YNV5169
10 Button(1-6) YAC5342 25 Connector YNV5170

11 Button(TA/AF, DOWN) YAC5343 26 Lighting Conductor YNV5171 B

12 Button(LEFT, UP, RIGHT) YAC5344 27 Grille Unit See Contrast table (2)
13 Button(SRC/BAND) YAC5345 28 Knob Unit YXC5102
14 Button(LIST/DISP) YAC5346 29 Spring YBL5010
15 Button(DETACH) YAC5347 30 •••••

(2) CONTRAST TABLE

DEH-2100UB/XS/EW5, DEH-2120UB/XS/EW5 and DEH-2110UB/XS/UR are constructed the same except for the
following:
Mark No. Description DEH-2100UB/XS/EW5 DEH-2120UB/XS/EW5 DEH-2110UB/XS/UR
C
1 Cord Assy CDP1015 CDP1015 CDP1016
6 Detachable Assy YXA5546 YXA5551 YXA5547
27 Grille Unit YXA5498 YXA5499 YXA5501

DEH-2100UB/XS/EW5
5 6 7 8
37
 1 2 3 4

9.4 CD MECHANISM MODULE

5
19
A

27
5
19 5

(1)

19

29 A
13 48 20
5
19 57
(1)
B B

66 16
13
(1)

9 25
54
44 (1)
23
31 C
44 9 (2)

15 58
73
72
60
8 69 21
(2)
C 46 71 70
38 33
39 62
70 7
68 63
50
40 4
36 (2) (1)
28 (1)
B
32 (1)
52 53
(1) 4
(2) 47 (1) (2)
18 17 35
(1)
37 45 C
61
14 6
D 41 12
(1)
5 49 A
8 64 (2)

(1)
51 65
D
55 (2)
(1)

51 59
(1)

43 10
C (1)
E
74 56
D (2)
1
(1)
3 22
2
E 34 (1)

(1)
19 (1) (1)

26
11
42
24 (1)

(1)

(1)
30
19

F
67
24 E
(1) : GEM1024
(2) : GEM1045

DEH-2100UB/XS/EW5
38
1 2 3 4
 5 6 7 8

CD MECHANISM MODULE SECTION PARTS LIST

Mark No. Description Part No. Mark No. Description Part No.

1 CD Core Unit(S10.5COMP2-USB-C2) CWX3679 50 Rack CNV8342

2 Connector(CN101) CKS4808 A
3 Connector(CN701) CKS5854 51 Roller CNV8343
4 Screw BMZ20P025FTC 52 Holder CNV8344
5 Screw BSZ20P040FTC 53 Arm CNV8345
54 Guide CNV9498
6 Screw(M2 x 3) CBA1511 55 Arm CNV8348
7 Screw(M2 x 4) CBA1835
8 Washer CBF1038 56 Arm CNV8349
9 Roller CNV9499 57 Arm CNV8350
10 Spring CBH2609 58 Clamper CNV8365
59 Arm CNV8386
11 Spring CBH2612 60 Guide CNV8396 B
12 Spring CBH2614
13 Spring CBH2616 61 Arm CNV9521
14 Spring CBH2617 62 Collar CNV8447
15 Spring CBH2620 63 Motor Unit(M2) CXC4026
64 Arm Unit CXC4027
16 Spring CBH2855 65 Chassis Unit CXC4028
17 Spring CBH2937
18 Spring CBH2735 66 Gear Unit CXC4029
19 Spring CBH2854 67 Frame Unit CXC4031
20 Spring CBH2642 68 Motor Unit(M1) CXC7134
69 Screw Unit CXC6359 C

21 Spring CBH2856 70 Screw JFZ20P025FTC

22 Spring CBH2857
23 Spring CBH2860 71 Screw JGZ17P022FTC
24 Spring CBH2861 72 Washer YE20FTC
25 Spring CBL1686 73 Pickup Unit(P10.5)(Service) CXX1942
74 Screw IMS26P030FTC
26 Arm CND1909
27 Frame CND2582
28 Bracket CND2583
29 Arm CND3831 D
30 Lever CND2585

31 Arm CND2586
32 Bracket CND2587
33 Arm CND2588
34 Lever CND2589
35 Holder CNV9522

36 Gear CNV7207
37 Gear CNV9513
38 Gear CNV7209 E
39 Gear CNV9514
40 Gear CNV9515

41 Gear CNV9516
42 Rack CNV9517
43 Arm CNV7216
44 Roller CNV8189
45 Gear CNV9518

46 Guide CNV9519
F
47 Gear CNV7595
48 Guide CNV9520
49 Arm CNV7805

DEH-2100UB/XS/EW5
5 6 7 8
39
 1 2 3 4

10. SCHEMATIC DIAGRAM

10.1 TUNER AMP UNIT(GUIDE PAGE)
A Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or
"ELECTRICAL PARTS LIST".
Large size
SCH diagram NM : No Mount
A-a
A-a A-b C CN701
NOTE :
Symbol indicates a resistor.
No differentiation is made between chip resistors and
discrete resistors.
Symbol indicates a capacitor.
No differentiation is made between chip capacitors and
A-a A-b Guide page discrete capacitors.

For resistors and capacitors in the circuit diagrams, their resistance values or
capacitance values are expressed in codes:

Ex. *Resistors *Capacitors

A-a A-b Detailed page Code Practical value Code Practical value
123 12k ohms 103 0.01uF
103 10k ohms 101/10 100uF/10V
B
FM/AM TUNER UNIT

A,B

A,B:CWE2106
C:CWE2123

ANTENNA

A,B
A,B:103
C:104

D
A,B:103
C:104

A,B

E
B
CN1801

A
DEH-2100UB/XS/EW5
40
1 2 3 4
 5 6 7 8

701
A-b A TUNER AMP UNIT
A : DEH-2100UB/XS/EW5
B : DEH-2120UB/XS/EW5
C : DEH-2110UB/XS/UR

3A B
>

C D

POWER IC 600uH
>
YEK5001
10A

A,B
A,B

The > mark found on some component parts indicates

the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of
identical designation.
A
DEH-2100UB/XS/EW5
5 6 7 8
41
 F
E
B
A

D
C

42
A-a A-b
A-b A TUNER AMP UNIT
A : DEH-2100UB/XS/EW5
B : DEH-2120UB/XS/EW5

1
1

C : DEH-2110UB/XS/UR

3A

>

2
2

DEH-2100UB/XS/EW5
3
3

4
4
 C
5

5
POWER IC 600uH
>
YEK5001
10A

6
6

DEH-2100UB/XS/EW5
7
7

A,B
A,B
8

8
The > mark found on some component parts indicates
the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of
identical designation.

A-a A-b
A-b

43
E
A

D
C

F
B
 F
E
B
A

D
C

44
A-a A-b
NM : No Mount
A-b
C CN701

A-a
NOTE :
Symbol indicates a resistor.

1
1

No differentiation is made between chip resistors and

discrete resistors.
Symbol indicates a capacitor.
No differentiation is made between chip capacitors and
discrete capacitors.

For resistors and capacitors in the circuit diagrams, their resistance values or
capacitance values are expressed in codes:
Ex. *Resistors *Capacitors
Code Practical value Code Practical value
123 12k ohms 103 0.01uF
103 10k ohms 101/10 100uF/10V

2
2

DEH-2100UB/XS/EW5
A,B

3
3

FM/AM TUNER UNIT

A,B:CWE2106
C:CWE2123

4
4

ANTENNA

A,B
C:104
A,B:103
 5 6 7 8

A-b
A

B CN1801

C
A,B

C:104
A,B:103
C

C:104

A-a A-b
A,B:103
A,B

A-a
DEH-2100UB/XS/EW5
5 6 7 8
45
 1 2 3 4

10.2 KEYBOARD UNIT

MC2848-11
MC2848-11
473

PD6340A
5.00 MHz

A,C B

561
391

B
DEH-2100UB/XS/EW5
46
1 2 3 4
 5 6 7 8

A : DEH-2100UB/XS/EW5
B : DEH-2120UB/XS/EW5 B KEYBOARD UNIT A

C : DEH-2110UB/XS/UR

AUX

MULTI-CONTROL

A
CN831
C

561
391

USB

B
DEH-2100UB/XS/EW5
5 6 7 8
47
 1 2 3 4

10.3 CD MECHANISM MODULE(GUIDE PAGE)

A C-a

PICKUP UNIT(P10.5)(SERVICE)

F
T
C
S

B
F

T
F

T
F
F
T F
F
T T
T

C c

SWITCHES:
CD CORE UNIT(S10.5COMP2-iPod-C2)
S901:HOME SWITCH.........ON-OFF
S903:DSCSNS SWITCH.....ON-OFF
S904:12EJ SWITCH............ON-OFF
S905:8EJ SWITCH..............ON-OFF

The underlined indicates the switch position.

M1 CXC7134
SPINDLE MOTOR
S

C
M2 CXC4026
LOADING/CARRIAGE MOTOR e
T S

7
F 9 C

a 8 4
E
5

F
F
T
3
T

2
C
C
S
S

ACTUATOR/
MOTOR DRIVER

C
DEH-2100UB/XS/EW5
48
1 2 3 4
 5 6 7 8

C-b A

C CD CORE UNIT(S10.5COMP2-USB-C3)

SIGNAL LINE
F FOCUS SERVO LINE
T
TRACKING SERVO LINE
C
CARRIAGE SERVO LINE
S
SPINDLE SERVO LINE
b

PE5666A

D
l
k

A
CN651
6

i
g h j

C
DEH-2100UB/XS/EW5
5 6 7 8
49
 F
E
B
A

D
C

50
C-a C-b

C-b
1
1

C CD CORE UNIT(S10.5COMP2-USB-C3)

1
2
SIGNAL LINE
F FOCUS SERVO LINE
T
TRACKING SERVO LINE
C
CARRIAGE SERVO LINE
S
SPINDLE SERVO LINE
b

2
2

DEH-2100UB/XS/EW5
PE5666A

3
3

4
4

m
 5 6 7 8

CN651
A
A

i
j
B

h
g
C

C-a C-b
D
m

l
k

C-b
DEH-2100UB/XS/EW5
5 6 7 8
51
 F
E
B
A

D
C

52
C-a C-b

C-a
C-b

1
1

1
2

PICKUP UNIT(P10.5)(SERVICE)

F
T
C

2
2

T
F

DEH-2100UB/XS/EW5
T
F
F

3
3

T F
F
T T
T

4
4

SWITCHES:
CD CORE UNIT(S10.5COMP2-iPod-C2)
S901:HOME SWITCH.........ON-OFF
S903:DSCSNS SWITCH.....ON-OFF
S904:12EJ SWITCH............ON-OFF
S905:8EJ SWITCH..............ON-OFF
 SWITCHES:
CD CORE UNIT(S10.5COMP2-iPod-C2)
S901:HOME SWITCH.........ON-OFF
S903:DSCSNS SWITCH.....ON-OFF
S904:12EJ SWITCH............ON-OFF
S905:8EJ SWITCH..............ON-OFF

The underlined indicates the switch position.

5

5
M1 CXC7134
SPINDLE MOTOR
S

C
M2 CXC4026

6
6

LOADING/CARRIAGE MOTOR e
T S

7
F 9 C

a 8 4
5

F
F
T
3

DEH-2100UB/XS/EW5
T

7
7

2
S
C
C

ACTUATOR/
MOTOR DRIVER
8

8
C-a C-b

C-a
C-b

53
E
A

D
C

F
B
 1 2 3 4

10.4 WAVEFORMS

- CD CORE UNIT Note : 1. The encircled numbers denote measuring points in the circuit diagram.
A
2. Reference voltage REFO1(1.65 V)

1DSCSNS 5 V/div 500 ms/div 1DSCSNS 5 V/div 500 ms/div 1DSCSNS 5 V/div 500 ms/div
28SNS 5 V/div 5CLCONT 5 V/div 28SNS 5 V/div
312SNS 5 V/div 4LOEJ 5 V/div 312SNS 5 V/div
4LOEJ 5 V/div 6VD 10 V/div 4LOEJ 5 V/div
12 cm CD Loading operation 12 cm CD Loading operation 8 cm CD Loading operation

Ref.: Ref.: Ref.:

GND GND GND
B
Mode: Mode: Mode:
Normal Normal Normal

7SIN 1 V/div 1 s/div 0FIN 200 mV/div 500 ms/div @TE 500 mV/div 200 ms/div
8CIN 500 mV/div !RFOK(MONI_3) 2 V/div #FE 500 mV/div
9TIN 1 V/div 7SIN 2 V/div

12 cm CD-DA setup operation after loading 12 cm CD-DA Source On setup operation Source On setup operation

Ref.: Ref.: Ref.:

REFO REFO REFO

Mode: Mode: Mode:

Normal Normal Normal

#FE 500 mV/div 20 ms/div $MDX 2 V/div 200 ms/div $MDX 2 V/div 5 µs/div
0FIN 500 mV/div 7SIN 500 mV/div 7SIN 500 mV/div
@TE 500 mV/div
D 9TIN 500 mV/div
CD-DA Play operation Spindle waveform during play operation Spindle waveform during play operation
(Wider)

Ref.: Ref.: Ref.:

REFO REFO REFO

Mode: Mode: Mode:

Normal Normal Normal

E
0FIN 500 mV/div 200 ms/div @TE 500 mV/div 2 ms/div %RFAGC 1 V/div 500 µs/div
#FE 500 mV/div %RFAGC 500 mV/div @TE 500 mV/div
9TIN 500 mV/div

Focus Search waveform Track Open waveform 1 Track Jump waveform

Ref.: Ref.: Ref.:

REFO REFO REFO

Mode: Mode: Mode:

F TEST TEST TEST

DEH-2100UB/XS/EW5
54
1 2 3 4
 5 6 7 8

A
%RFAGC 1 V/div 500 µs/div %RFAGC 1 V/div 500 µs/div %RFAGC 1 V/div 2 ms/div
@TE 500 mV/div @TE 500 mV/div @TE 500 mV/div
9TIN 500 mV/div 9TIN 500 mV/div 9TIN 500 mV/div

4 Tracks Jump waveform 10 Tracks Jump waveform 32 Tracks Jump waveform

Ref.: Ref.: Ref.:

REFO REFO REFO

Mode: Mode: Mode:

TEST TEST TEST B

%RFAGC 1 V/div 200 ms/div ^LOUT 1 V/div 200 µs/div 1DSCSNS 5 V/div 500 ms/div
@TE 1 V/div &ROUT 1 V/div 28SNS 5 V/div
8CIN 1 V/div 312SNS 5 V/div
7SIN 2 V/div 4LOEJ 5 V/div
Search operation(Outter to Inner) Analog audio waveform 12 cm CD Eject operation

Ref.: Ref.: Ref.: C

REFO AGND GND

Mode: Mode: Mode:

Normal Normal Normal

1DSCSNS 5 V/div 500 ms/div 1DSCSNS 5 V/div 500 ms/div %RFAGC 1 V/div 500 µs/div
5CLCONT 5 V/div 28SNS 5 V/div 9TIN 1 V/div
4LOEJ 5 V/div 312SNS 5 V/div @TE 1 V/div
4LOEJ 5 V/div 0FIN 1 V/div
12 cm CD Eject operation 8 cm CD Eject operation Black dot(800 µm) during play D

Ref.: Ref.: Ref.:

GND GND REFO

Mode: Mode: Mode:

Normal Normal Normal

*DP 1 V/div 50 ns/div *DP 2 V/div 50 ms/div *DP 2 V/div 50 ms/div

(DM 1 V/div (DM 2 V/div (DM 2 V/div E

USB Play USB device inserting to USB connector. CD Play with USB(iPod) device connecting.

DEH-2100UB/XS/EW5
5 6 7 8
55
 1 2 3 4

A
*DP 2 V/div 50 ms/div )CPRST 2 V/div 500 ms/div
(DM 2 V/div ⁄SDA 2 V/div
¤SCL 2 V/div

ACC OFF with USB(iPod) device connecting. iPod Authentication Operation

DEH-2100UB/XS/EW5
56
1 2 3 4
5 6 7 8

DEH-2100UB/XS/EW5
5 6 7 8
57
 1 2 3 4

11. PCB CONNECTION DIAGRAM

11.1 TUNER AMP UNIT
A NOTE FOR PCB DIAGRAMS
1.The parts mounted on this PCB
include all necessary parts for
A TUNER AMP UNIT
several destination.
For further information for
respective destinations, be sure
to check with the schematic dia- CORD ASSY
gram.
2.Viewpoint of PCB diagrams
Connector Capacitor

SIDE A

B
SIDE B
P.C.Board Chip Part

E
C CN701

F B CN1801

A
DEH-2100UB/XS/EW5
58
1 2 3 4
 5 6 7 8

A
SIDE A

W.REM(2100, 2120) RCA

ASSY

ANTENNA

FM/AM TUNER UNIT

F
FRONT

A
DEH-2100UB/XS/EW5
5 6 7 8
59
 1 2 3 4

A
A TUNER AMP UNIT

> FU 351 (B,138,128) Fuse 3 A CEK1286

A
DEH-2100UB/XS/EW5
60
1 2 3 4
5 6 7 8

SIDE B
A

A
DEH-2100UB/XS/EW5
5 6 7 8
61
 F
E
B
A

D
C

62
B
B

1
1

KEYBOARD UNIT
11.2 KEYBOARD UNIT

2
2

D1840
D1857

40
S1802 S1803
S1823 S1830 S1829 S1819
LCD1801 S1834
EJECT

D1832
D1849
40 35 30 25 20 15 10 5 1

30 CN1803

D1830
D1847
5

LIST TA/RF
1

S1831
S1828

D1825
D1842
D1823

D1826
D1843
SOURCE MULTI-CONTROL USB
20 D1828
S1833 D1848
D1845

DEH-2100UB/XS/EW5
BAND/ESC D1831
S1827

D1824
D1844

D1841
D1829
CN1802
1 2 3 4 5 6 IC1802
S1801 S1809 S1807 S1805 S1811 S1813

3
3

S1817 S1832 S1815 AUX

D1850
D1836
D1837
D1854
D1856
D1839

D1835
D1851
D1838

D1834
D1852
D1855

10 S1825 S1826
1

D1846
D1827
Y DISP/BACK

0
10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160
X

4
4

SIDE A
 B

F
C

D
A

63
B
SIDE B

8
8

A CN831
40
7

7
R1818
R1837

DEH-2100UB/XS/EW5
R1813
D1807

30
D1806

50 R1809
L1801
R1832
1

45 R1808
55
40
60
D1803

R1833
R1806

C1807

C1802
R1804

35
D1804

R1810 R1811
C1803

IC1801
R1838 20

R1836
1 R1814
C1806
D1805
C1805

30 R1812

R1839
5 Q1806
R1820

15 5 1
25

E
C1804

10 R1835
R1807 20 Q1805

5
15

1
R1816

R1829
R1803 R1801 R1817
X1801 1 CN1801 10
R1834

R1815

D1801

D1802
R1802 C1801 R1819

R1828
6

6
20 10
Y
0
160 150 140 130 120 110 100 90 80 70 60 50 40 30 20 10
X
KEYBOARD UNIT

5
5

B
 1 2 3 4

11.3 CD CORE UNIT(S10.5COMP2-USB-C3)

C CD CORE UNIT(S10.5COMP2-USB-C3) SIDE A

A

PICKUP UNIT(P10.5)
(SERVICE)

A CN651

REFO1
F
E

D HOME

M2
LOADING/CARRIAGE
MOTOR
M1
SPINDLE MOTOR

C
DEH-2100UB/XS/EW5
64
1 2 3 4
 5 6 7 8

C CD CORE UNIT(S10.5COMP2-USB-C3) SIDE B

A

8EJ B

12EJ

DSCSNS

C
DEH-2100UB/XS/EW5
5 6 7 8
65
 1 2 3 4

12. ELECTRICAL PARTS LIST

NOTE:
A Parts whose parts numbers are omitted are subject to being not supplied.
The part numbers shown below indicate chip components.
Chip Resistor
RS1/_S___J,RS1/__S___J
Chip Capacitor (except for CQS.....)
CKS....., CCS....., CSZS.....
The > mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
Meaning of the figures and others in the parentheses in the parts list.
B Example) IC 301 is on the point (face A, 91 of x-axis, and 111 of y-axis) of the corresponding
PC board.
IC 301 (A, 91, 111) IC NJM2068V
The expression of the unit in this manual is shown by u instead of µ. Please do not make a mistake.
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
Q 201 (B,131,130) Transistor RT3T22M
A:DEH-2100UB/XS/EW5 Q 351 (B,160,128) Transistor RT3N66M
B:DEH-2120UB/XS/EW5 Q 601 (A,150,68) Transistor 2SD1858
Q 821 (B,21,17) Transistor 2SA1036K
C:DEH-2110UB/XS/UR
C Q 822 (B,21,12) Transistor LTC114EUB
Unit Number : YWM5292(A) Q 851 (B,71,115) Transistor(A,B) 2SA1036K
Q 931 (B,60,118) Transistor LSC4081UB
Unit Number : YWM5317(B) Q 991 (A,7,117) Transistor 2SD2396
Q 992 (B,12,107) Transistor RT3T22M
Unit Number : YWM5316(C)
Unit Name : Tuner Amp Unit D 301 (A,65,129) Diode 1SR139-400
D 302 (A,53,130) Diode 1SR139-400
Unit Number : D 501 (B,66,91) Diode RB060L-40
D 502 (A,50,105) Diode 1SR139-400
Unit Name : Keyboard Unit D 601 (B,136,19) Diode(A,B) RB551V-30

Unit Number : CWX3679 D 602 (B,128,15) Diode(A,B) RB751V-40

D D 840 (B,77,5) Varistor EZJZ1V270RM
Unit Name : CD Core D 841 (B,76,13) Varistor EZJZ1V270RM
Unit(S10.5COMP2-USB-C3) D 842 (B,33,12) Varistor EZJZ1V800AM
D 843 (B,33,11) Varistor EZJZ1V800AM

D 844 (B,80,4) Varistor EZJZ1V270RM

model D 845 (B,78,16) Varistor EZJZ1V270RM
A:DEH-2100UB/XS/EW5 D 851 (B,70,121) Diode(A,B) MC2848-11
D 901 (A,53,124) Diode 1SR139-400
B:DEH-2120UB/XS/EW5 D 902 (A,53,127) Diode 1SR139-400
C:DEH-2110UB/XS/UR
D 911 (A,53,77) Diode 1SR139-400

E
A
Unit Number : YWM5292(A)
D
D
D
912
931
991
(A,44,82) Diode
(A,59,124) Diode
(A,19,114) Diode
1SR139-400
HZS7L(A1)
HZS7L(C3)
L 151 (A,134,119) Inductor LAU2R2K
Unit Number : YWM5317(B)
Unit Number : YWM5316(C) L 401 (A,149,83) Inductor LAU2R2K
Unit Name : Tuner Amp Unit L 402 (A,147,94) Inductor LAU2R2K
L 407 (B,164,71) Inductor CTF1473
L 501 (A,68,94) Inductor VTL1118
MISCELLANEOUS L 561 (B,42,91) Resistor RS1/10S0R0J
L 601 (B,120,23) Inductor CTF1389
IC 151 (B,127,105) IC PML014A
IC 251 (B,69,87) IC BD6538G L 602 (A,148,25) Inductor LAUR47K
IC 301 (A,91,135) IC PAL007C L 603 (A,111,81) Inductor LAU2R2K
F IC 501 (B,64,100) IC BD9007F L 604 (A,119,68) Inductor LAUR47K
IC 601 (B,128,45) IC PN5024B L 605 (A,127,70) Inductor LAUR47K
L 606 (A,146,70) Inductor LAU1R0K
IC 911 (A,16,65) IC BA49181-V12

DEH-2100UB/XS/EW5
66
1 2 3 4
 5 6 7 8
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
L 607 (A,147,62) Inductor LAU1R0K R 513 (B,65,86) RS1/16S0R0J
L 608 (A,134,70) Inductor LAU1R5K R 520 (B,75,97) RS1/16S0R0J
L 609 (A,131,70) Inductor LAU1R5K
L 610 (A,144,67) Inductor LAU1R2J R 601 (B,123,28) RS1/16S473J A
L 611 (B,135,81) Inductor CTF1379 R 602 (B,106,41) RS1/16S473J
R 606 (B,107,71) RS1/16S473J
L 612 (B,133,81) Inductor CTF1379 R 607 (B,136,25) RAB4C104J
L 613 (B,144,62) Inductor CTF1379 R 608 (B,140,61) RS1/16S470J
L 614 (B,123,62) Inductor CTF1379
L 615 (B,146,54) Inductor CTF1389 R 609 (B,106,48) RS1/16S473J
L 616 (B,151,76) Inductor CTF1379 R 610 (B,117,72) RS1/16S203J
R 611 (B,138,72) RS1/16S182J
L 617 (B,142,78) Inductor CTF1379 R 612 (B,114,74) RS1/16S563J
L 618 (B,127,23) Inductor CTF1379 R 613 (B,141,53) RS1/16S302J
L 619 (B,115,65) Inductor CTF1379
L 801 (A,15,39) Inductor LAU2R2K R 615 (B,111,73) RS1/16S563J
L 851 (A,65,131) Inductor(A,B) LAU2R2K R 616 (B,154,40) RS1/16S104J B
R 617 (B,137,32) RS1/16S473J
L 901 (A,35,99) Choke Coil 600 uHCTH1280 R 618 (B,147,42) RS1/16S473J
X 601 (A,141,63) Oscillator 74.100 MHzCSS1749 R 619 (B,147,40) RS1/16S104J
X 602 (A,114,59) Oscillator 4.7186 MHz(C)CSS1727
FU351 (B,138,128) Fuse 3 A CEK1286 R 622 (B,130,28) RS1/16S104J
AR401 (B,164,117) Surge ProtectorIMSA-6801-01Y901 R 623 (B,134,17) (A,B) RS1/16S103J
(B,134,17) (C) RS1/16S104J
RESISTORS R 624 (B,126,14) (A,B) RS1/16S103J
(B,126,14) (C) RS1/16S104J
R 151 (B,115,97) RS1/16S102J R 638 (B,159,94) RS1/16S273J
R 152 (B,98,103) RS1/16S102J R 643 (B,154,38) RS1/16S104J
R 153 (B,123,93) RS1/16S102J
R 170 (B,106,96) RS1/16S0R0J R 645 (B,36,27) RS1/16S120J C
R 171 (B,141,101) RS1/16S102J R 646 (B,44,24) RS1/16S120J
R 651 (B,31,29) RS1/16S104J
R 172 (B,111,106) RS1/16S102J R 652 (B,31,34) RS1/16S102J
R 173 (B,144,104) RS1/16S681J R 653 (B,31,33) RS1/16S102J
R 174 (B,111,103) RS1/16S681J
R 175 (B,144,99) RS1/16S223J R 654 (B,31,31) RS1/16S221J
R 176 (B,111,104) RS1/16S223J R 656 (B,106,28) RS1/16S104J
R 657 (B,106,30) RS1/16S104J
R 201 (B,128,123) RS1/16S103J R 658 (B,32,37) RS1/16S104J
R 202 (B,121,135) RS1/16S153J R 659 (B,106,32) RS1/16S472J
R 203 (B,120,135) RS1/16S221J
R 254 (B,74,88) RS1/16S561J R 660 (B,106,34) RS1/16S472J
R 257 (B,75,102) RS1/16S473J R 661 (B,109,30) RS1/16S221J D
R 662 (B,109,32) RS1/16S221J
R 301 (B,83,108) RS1/16S153J R 663 (B,109,34) RS1/16S221J
R 351 (B,165,132) RS1/16S223J R 664 (B,19,41) RS1/16S104J
R 352 (B,165,136) RS1/16S223J
R 353 (B,157,125) RS1/16S821J R 665 (B,116,22) RS1/16S0R0J
R 354 (B,164,127) RS1/16S821J R 666 (B,149,56) RS1/16S103J
R 670 (B,132,22) RS1/16S473J
R 401 (B,158,45) RS1/16S102J R 671 (B,132,27) (C) RS1/16S273J
R 404 (B,160,58) RS1/16S472J R 757 (B,61,69) RS1/16S0R0J
R 405 (B,160,55) RS1/16S682J R 758 (B,58,77) RS1/16S0R0J
R 406 (B,160,61) RS1/16S102J
R 407 (B,160,63) RS1/16S102J R 759 (B,62,77) RS1/16S0R0J
E
R 803 (B,17,36) RS1/16S222J
R 408 (B,170,56) RAB4C104J R 821 (B,20,20) RS1/16S562J
R 409 (B,160,48) RS1/16S391J R 822 (B,26,18) RS1/16S103J
R 410 (B,160,50) RS1/16S681J R 831 (B,55,17) RS1/16S1R0J
R 411 (B,160,52) RS1/16S681J
R 412 (B,160,54) RS1/16S681J R 832 (B,71,18) RS1/16S473J
R 833 (A,75,28) RD1/4PU222J
R 502 (B,75,95) RS1/16S4702F R 834 (A,79,25) RD1/4PU222J
R 503 (B,76,98) RS1/16S562J R 836 (B,64,34) RS1/16S104J
R 505 (B,73,91) RS1/16S1002F R 837 (A,74,21) RD1/4PU103J
R 506 (B,71,96) RS1/16S393J
R 507 (B,113,37) RS1/16S222J R 838 (B,71,20) RS1/16S222J
R 839 (B,93,15) RS1/16S222J F
R 508 (B,60,95) RS1/16S513J R 840 (B,93,17) RS1/16S222J
R 509 (B,59,92) RS1/16S392J R 851 (B,74,116) (A,B) RS1/16S472J
R 511 (B,62,87) RS1/10SR471J R 852 (B,70,119) (A,B) RS1/16S472J

DEH-2100UB/XS/EW5
5 6 7 8
67
 1 2 3 4
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 853 (B,68,124) (A,B) RS1/16S153J C 604 (B,143,74) CKSRYB103K50
R 854 (B,63,115) (A,B) RS1/16S102J C 605 (B,108,74) CKSRYB104K16
R 855 (B,59,115) RS1/16S104J C 606 (B,105,62) CKSRYB103K50
R 871 (B,123,134) (A,B) RS1/16S102J C 607 (B,117,56) CKSRYB103K50
A
R 872 (B,128,124) (A,B) RS1/16S102J C 608 (B,99,81) CKSRYB103K50

R 888 (B,76,4) RS1/16S0R0J C 609 (B,114,73) CKSRYB331K50

R 931 (B,105,41) RS1/16S104J C 610 (A,97,83) CEJQ101M6R3
R 932 (B,66,117) RS1/16S223J C 611 (B,114,71) CKSRYB331K50
R 933 (A,59,126) RD1/4PU102J C 612 (B,119,60) CKSRYB103K50
R 934 (B,66,122) RS1/16S472J C 613 (A,103,59) CEAL101M6R3

R 935 (B,66,119) RS1/16S473J C 614 (B,169,94) CKSRYB102K50

R 991 (A,13,122) RD1/4PU271J C 615 (B,123,61) CKSRYB331K50
C 616 (B,122,67) CKSRYB105K10
CAPACITORS C 617 (B,129,62) CKSRYB105K10
B C 618 (B,111,55) (C) CCSRCH270J50
C 151 (B,117,101) CKSRYB224K10 C 620 (B,144,58) CKSRYB105K10
C 152 (B,141,99) CKSRYB224K10
C 153 (B,117,99) CKSRYB105K10 C 622 (B,141,55) CKSRYB104K16
C 154 (B,138,98) CKSRYB105K10 C 623 (B,133,66) CKSRYB102K50
C 155 (A,120,116) CEJQ470M10 C 624 (B,131,67) CKSRYB102K50
C 625 (B,136,73) CCSRCH270J50
C 158 (B,117,103) CKSRYB105K10 C 626 (B,130,73) CCSRCH270J50
C 161 (B,141,105) CKSRYB105K10
C 164 (A,114,111) CEJQ100M16 C 627 (B,134,79) CCSRCH150J50
C 165 (B,123,116) CKSRYB104K16 C 628 (B,142,65) CKSRYB102K50
C 170 (B,131,92) CKSRYB104K16 C 629 (B,135,60) CCSRCH4R0C50
C 630 (B,143,70) CCSRCH8R0D50
C C 171 (B,138,103) CKSRYB105K10 C 631 (B,108,72) CKSRYB223K50
C 172 (B,117,104) CKSRYB105K10
C 201 (A,132,135) CEJQ330M10 C 632 (B,129,24) CKSRYB104K16
C 251 (B,66,4) CKSRYB105K10 C 633 (B,142,31) CKSRYB104K16
C 301 (B,125,126) CKSQYB474K25 C 634 (B,111,59) (C) CCSRCH270J50
C 635 (B,145,55) CKSRYB104K16
C 302 (B,121,124) CKSQYB474K25 C 640 (B,143,72) CKSRYB103K50
C 303 (B,123,126) CKSQYB474K25 C 641 (B,123,59) CKSRYB104K16
C 304 (B,118,124) CKSQYB474K25
C 305 (B,120,132) CKSRYB474K16 C 642 (B,114,99) CKSRYB122K50
C 306 (B,118,129) CKSRYB474K16 C 643 (B,141,97) CKSRYB122K50
C 645 (B,116,20) CKSRYB103K50
C 307 (B,120,131) CKSRYB474K16 C 651 (B,22,27) CKSRYB102K50
D C 308 (B,115,124) CKSRYB474K16 C 652 (B,47,36) CKSRYB221K50
C 309 (B,120,140) CKSQYB225K10
C 310 (B,117,141) CKSQYB225K10 C 653 (B,113,35) CCSRCH220J50
C 312 (A,103,123) CEJQ100M16 C 654 (B,27,42) CKSRYB102K50
C 655 (B,25,41) CKSRYB104K16
C 313 (B,97,142) CKSRYB104K16 C 668 (B,128,78) CKSRYB105K10
C 353 (A,154,121) CEJQ2R2M50 C 669 (B,129,22) CKSRYB105K10
C 354 (A,148,121) CEJQ2R2M50
C 359 (B,164,138) CCSQCH102J50 C 670 (B,140,79) CKSRYB104K16
C 401 (B,169,71) (A,B) CKSRYB104K16 C 821 (B,19,14) CKSRYB104K16
C 831 (B,66,28) CCSRCH221J50
C 404 (A,150,97) CEJQ101M10 C 832 (B,66,27) CCSRCH221J50
C 405 (B,148,101) CKSRYB103K50 C 833 (B,64,32) CKSRYB104K16
E
C 406 (B,170,59) CCSRCH390J50
C 409 (B,158,46) CCSRCH100D50 C 834 (B,64,30) CCSRCH221J50
C 411 (B,162,45) CCSRCH151J50 C 839 (B,79,13) CCSRCH221J50
C 840 (B,73,25) CCSRCH221J50
C 412 (B,169,96) CKSRYB104K16 C 841 (B,71,22) CCSRCH221J50
C 501 (A,60,89) 150 uF/6.3 V CCH1804 C 871 (B,130,138) (A,B) CKSRYB103K50
C 502 (A,56,94) CEJQ221M16
C 504 (B,58,103) CKSQYB225K16 C 872 (B,130,132) (A,B) CKSRYB103K50
C 505 (B,71,98) CCSRCH101J50 C 901 (A,46,115) 3 300 uF/16 V CCH1732
C 911 (A,58,63) CEJQ100M16
C 506 (B,71,99) CKSRYB153K50 C 912 (A,47,69) CEAT102M16
C 508 (B,57,88) CKSRYB105K10 C 913 (B,28,73) CKSRYB104K16
F C 601 (B,119,27) CKSRYB105K10
C 602 (B,119,29) CKSRYB103K50 C 914 (A,49,63) CEAT221M10
C 603 (B,122,28) CKSRYB103K50 C 915 (A,54,51) CEJQ100M16
C 917 (B,27,78) CKSRYB104K16
C 991 (B,10,109) CKSRYB473K25
DEH-2100UB/XS/EW5
68
1 2 3 4
 5 6 7 8
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
C 992 (A,12,97) CEJQ101M10 C 1807 (B,126,19) CKSRYB472K50

B
Unit Number : (A)(C)
B
Unit Number : (B)
A

Unit Name : Keyboard Unit Unit Name : Keyboard Unit

MISCELLANEOUS MISCELLANEOUS

IC 1801 (B,100,20) IC PD6340A IC 1801 (B,100,20) IC PD6340A

D 1801 (B,103,6) Diode MC2848-11 D 1801 (B,103,6) Diode MC2848-11
D 1802 (B,100,6) Diode MC2846-11 D 1802 (B,100,6) Diode MC2846-11
D 1803 (B,135,20) Varistor EZJZ1V270RM D 1803 (B,135,20) Varistor EZJZ1V270RM
D 1804 (B,128,18) Varistor EZJZ1V270RM D 1804 (B,128,18) Varistor EZJZ1V270RM

D 1805 (B,138,20) Varistor EZJZ1V270RM D 1805 (B,138,20) Varistor EZJZ1V270RM B

D 1806 (B,139,26) Diode MALS068X D 1806 (B,139,26) Diode MALS068X
D 1807 (B,141,27) Diode MALS068X D 1807 (B,141,27) Diode MALS068X
D 1823 (A,139,22) White LED NESW505C-5273 D 1823 (A,139,22) White LED NESW505C-5273
D 1824 (A,6,13) LED CL-195SR-CD D 1824 (A,6,13) LED CL-195PG-CD

D 1825 (A,5,30) LED CL-195SR-CD D 1825 (A,5,30) LED CL-195PG-CD

D 1826 (A,15,28) LED CL-195SR-CD D 1826 (A,15,28) LED CL-195PG-CD
D 1827 (A,39,5) LED CL-195SR-CD D 1827 (A,39,5) LED CL-195PG-CD
D 1828 (A,24,19) LED CL-195SR-CD D 1828 (A,24,19) LED CL-195PG-CD
D 1829 (A,16,13) LED CL-195SR-CD D 1829 (A,16,13) LED CL-195PG-CD

D 1830 (A,37,33) LED CL-195SR-CD D 1830 (A,37,33) LED CL-195PG-CD

D 1831 (A,52,18) LED CL-195SR-CD D 1831 (A,52,18) LED CL-195PG-CD C
D 1832 (A,54,33) LED CL-195SR-CD D 1832 (A,54,33) LED CL-195PG-CD
D 1834 (A,91,8) LED CL-195SR-CD D 1834 (A,91,8) LED CL-195PG-CD
D 1835 (A,79,8) LED CL-195SR-CD D 1835 (A,79,8) LED CL-195PG-CD

D 1836 (A,68,8) LED CL-195SR-CD D 1836 (A,68,8) LED CL-195PG-CD

D 1837 (A,103,8) LED CL-195SR-CD D 1837 (A,103,8) LED CL-195PG-CD
D 1838 (A,115,8) LED CL-195SR-CD D 1838 (A,115,8) LED CL-195PG-CD
D 1839 (A,127,8) LED CL-195SR-CD D 1839 (A,127,8) LED CL-195PG-CD
D 1840 (A,146,41) LED CL-195SR-CD D 1840 (A,146,41) LED CL-195PG-CD

L 1801 (B,137,26) Inductor CTF1713 L 1801 (B,137,26) Inductor CTF1713

X 1801 (B,92,8) Ceramic Resonator 5.00 MHzCSS1731 X 1801 (B,92,8) Ceramic Resonator 5.00 MHzCSS1731
S 1833 (A,38,19) Rotary Switch CSD1153 S 1833 (A,38,19) Rotary Switch CSD1153 D
LCD1801 (A,133,32) LCD CAW1970 LCD1801 (A,133,32) LCD CAW1970

RESISTORS RESISTORS

R 1801 (B,102,10) RS1/16S473J R 1801 (B,102,10) RS1/16S473J

R 1806 (B,133,19) RS1/16S101J R 1806 (B,133,19) RS1/16S101J
R 1807 (B,134,14) RS1/16S101J R 1807 (B,134,14) RS1/16S101J
R 1809 (B,57,28) RS1/16S473J R 1809 (B,57,28) RS1/16S473J
R 1810 (B,138,23) RS1/4SA821J R 1810 (B,138,23) RS1/4SA821J

R 1811 (B,13,20) RS1/4SA821J R 1811 (B,13,20) RS1/4SA561J

R 1812 (B,13,14) RS1/4SA821J R 1812 (B,13,14) RS1/4SA561J
E
R 1813 (B,16,30) RS1/4SA821J R 1813 (B,16,30) RS1/4SA561J
R 1814 (B,73,18) RS1/4SA821J R 1814 (B,73,18) RS1/4SA561J
R 1815 (B,123,8) RS1/4SA681J R 1815 (B,123,8) RS1/4SA391J

R 1828 (B,87,6) RS1/16S222J R 1828 (B,87,6) RS1/16S222J

R 1829 (B,87,9) RS1/16S222J R 1829 (B,87,9) RS1/16S222J
R 1839 (B,21,16) RS1/16S0R0J R 1839 (B,21,16) RS1/16S0R0J

CAPACITORS CAPACITORS

C 1802 (B,119,19) CKSRYB105K10 C 1802 (B,119,19) CKSRYB105K10

C 1803 (B,130,18) CKSRYB472K50 C 1803 (B,130,18) CKSRYB472K50
C 1804 (B,133,17) CKSRYB472K50 C 1804 (B,133,17) CKSRYB472K50 F
C 1805 (B,136,20) CKSRYB472K50 C 1805 (B,136,20) CKSRYB472K50
C 1806 (B,139,20) CKSRYB472K50 C 1806 (B,139,20) CKSRYB472K50

DEH-2100UB/XS/EW5
5 6 7 8
69
 1 2 3 4
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
C 1807 (B,126,19) CKSRYB472K50 R 282 (A,30,61) RS1/16SS120J
R 283 (A,29,61) RS1/16SS120J

A
C
Unit Number : CWX3679
R
R
R
284
285
290
(B,29,63)
(B,28,63)
(B,24,43)
RS1/16SS153J
RS1/16SS153J
RS1/16SS103J
Unit Name : CD Core Unit(S10.5COMP2-USB-C3) R 291 (B,42,62) RS1/16SS272J
R 294 (A,31,62) RS1/16SS471J
MISCELLANEOUS R 307 (A,35,19) RS1/16SS183J
R 308 (A,37,19) RS1/16SS183J
IC 201 (A,35,46) IC PE5666A R 309 (A,35,21) RS1/16SS183J
IC 301 (A,28,15) IC BA5839FP
Q 101 (B,58,69) Transistor 2SA1577 R 310 (A,37,22) RS1/16SS183J
Q 102 (B,48,58) Chip Transistor 2SB1689 R 601 (B,30,31) RS1/16SS0R0J
X 201 (A,22,37) Ceramic Resonator 16.934 MHz CSS1603 R 602 (B,27,31) RS1/16SS0R0J
R 606 (B,28,23) RS1/16S0R0J
B
X 205 (B,33,63) Oscillator 48.000 MHz CSS1753 R 701 (B,11,37) RS1/16SS221J
S 901 (A,55,37) Switch(HOME) CSN1067
S 903 (B,19,58) Switch(DSCSNS) CSN1067 R 702 (A,23,56) RS1/16SS221J
S 904 (B,40,68) Switch(12EJ) CSN1068 R 708 (B,15,37) RS1/16S0R0J
S 905 (B,25,69) Switch(8EJ) CSN1068 R 712 (B,14,54) RS1/16SS0R0J
R 713 (B,14,53) RS1/16SS0R0J
RESISTORS
CAPACITORS
R 101 (B,61,74) RS1/10SR2R4J
R 102 (B,61,72) RS1/10SR2R4J C 106 (B,56,67) CKSQYB475K10
R 103 (B,61,71) RS1/10SR2R7J C 202 (A,28,57) CKSSYB104K10
R 104 (B,53,66) RS1/16SS222J C 204 (A,23,59) CKSSYB103K16
R 105 (B,44,57) RS1/16SS102J C 205 (B,27,41) CKSQYB475K10
C C 206 (A,23,40) CKSSYB104K10
R 107 (B,52,60) RS1/16SS105J
R 202 (A,27,32) RS1/16SS473J C 207 (A,24,37) CKSRYB104K16
R 203 (A,51,44) RS1/16S473J C 209 (B,35,34) CEVW220M6R3
R 204 (A,23,58) RS1/16SS221J C 210 (B,29,37) CKSSYB104K10
R 206 (B,10,26) RS1/16SS104J C 211 (A,28,35) CKSSYB104K10
C 212 (A,28,30) CKSRYB104K16
R 209 (B,18,52) RS1/16SS103J
R 210 (B,10,23) RS1/16SS102J C 213 (A,46,39) CKSSYB104K10
R 214 (B,49,50) RS1/16SS472J C 214 (A,29,33) CKSSYB104K10
R 216 (B,48,49) RS1/16SS472J C 216 (A,51,52) CKSSYB332K50
R 221 (A,51,48) RS1/16SS103J C 217 (A,48,51) CKSSYB104K10
C 218 (A,50,52) CKSSYB473K10
D R 222 (A,51,46) RS1/16SS103J
R 223 (B,13,43) RS1/16SS473J C 219 (A,47,53) CKSSYB104K10
R 225 (A,50,50) RS1/16SS103J C 220 (A,48,53) CKSSYB182K50
R 226 (A,50,51) RS1/16SS393J C 221 (A,46,54) CKSSYB104K10
R 227 (B,47,51) RS1/16SS562J C 222 (B,45,53) CCSSCH560J50
C 223 (B,47,53) CCSSCH4R0C50
R 228 (B,44,51) RS1/16SS122J
R 229 (B,46,53) RS1/16SS472J C 224 (A,44,55) CKSSYB104K10
R 230 (B,21,25) RS1/16SS0R0J C 226 (A,42,59) CCSSCH680J50
R 232 (B,45,51) RS1/16SS122J C 227 (A,42,61) CCSSCH470J50
R 233 (B,26,59) RS1/16SS103J C 228 (B,41,61) CKSSYB103K16
C 229 (B,48,60) CKSSYB104K10
R 234 (B,22,26) RS1/16SS473J
E
R 235 (A,26,59) RS1/16SS473J C 236 (A,49,58) CKSSYB104K10
R 237 (A,24,35) RS1/16SS151J C 239 (B,46,51) CCSSCH220J50
R 240 (B,14,26) RS1/16S473J C 240 (A,38,61) CKSSYB104K10
R 241 (B,13,25) RS1/16SS103J C 243 (B,22,41) CKSQYB475K103
C 250 (A,52,48) CKSSYB102K50
R 244 (B,22,55) RS1/16SS473J
R 249 (B,14,50) RS1/16SS103J C 251 (A,52,46) CKSSYB102K50
R 254 (A,25,64) RS1/16SS104J C 260 (A,28,61) CKSSYB104K10
R 255 (A,26,63) RS1/16SS104J C 261 (B,33,66) CCSSCH8R0D50
R 256 (A,25,62) RS1/16SS104J C 262 (B,31,66) CCSSCH8R0D50
C 293 (B,43,61) CKSSYB102K50
R 259 (A,27,66) RS1/16SS0R0J
F R 261 (A,26,65) RS1/16SS104J C 303 (A,36,19) CKSSYB472K25
R 262 (A,29,59) RS1/16SS0R0J C 304 (A,36,21) CKSSYB223K16
R 263 (A,27,63) RS1/16SS0R0J C 307 (A,22,11) CKSRYB104K16
R 280 (B,20,45) RS1/16SS103J C 308 (B,11,18) CKSRYB105K10

DEH-2100UB/XS/EW5
70
1 2 3 4
 5 6 7 8
Circuit Symbol and No. Part No.
C 703 (B,14,35) CCSSCH101J50

C 704 (B,11,36) CKSSYB102K50

C 711 (A,31,25) CKSSYB104K10 A

Miscellaneous Parts List

Pickup Unit(P10.5)(Service) CXX1942
M 1 Motor Unit(SPINDLE) CXC7134
M 2 Motor Unit(LOADING/CARRIAGE) CXC4026

DEH-2100UB/XS/EW5
5 6 7 8
71