PAW3205DB-TJ3T

PAW3205DB-TJ3T
LOW POWER WIRELESS MOUSE SENSOR
General Description
The PAW3205DB-TJ3T is a high performance and low power CMOS process optical mouse sensor with DSP
integration chip that serves as a non-mechanical motion estimation engine for implementing a computer wireless
mouse. With adaptive frame-rate control(AFC), this optical mouse sensor gains extra power saving during mouse
moving.

Features Key Specification

 Single power supply Operating voltage
Power Supply
 Precise optical motion estimation 2.1V ~ 3.6V (VDD)
technology
 Complete 2-D motion sensor Optical Lens 1:1

 Accurate motion estimation over a wide Speed Up to 30 inches/sec

range of surfaces
 High speed motion detection up to 30 Acceleration Up to 10 G
inches/sec
Resolution 600/ 800/ 1000(Default)/ 1300/ 1600 CPI
 High resolution up to 1600 CPI
 Power saving mode during times of no Frame Rate Up to 2400 frames/sec
movement
 Serial interface for programming and 1.5mA @ Mouse moving (Normal)
Typical
data transfer Operating 50uA @ Mouse not moving (Sleep1)
 Built-in low power Timer (LPT) for Current 12uA @ Mouse not moving (Sleep2)
sleep1/sleep2 mode (without I/O 10uA @ Power down mode
 MOTSWK pin to wake up mouse toggling) *not including LED, typical value
controller
 Wide operation range from 2.1V to 3.6V Package Staggered DIP8
 Adaptive frame rate control for extra
power saving during moving

Ordering Information
Order Number Part Description Resolution
PAW3205DB-TJ3T CMOS Optical Mouse Sensor 1000 CPI

All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 1
PixArt Imaging Inc.
E-mail: [email protected] V1.0, May. 2013
PixArt Imaging Inc.

PAW3205DB-TJ3T Wireless Optical Mouse Sensor

1. Pin Configuration
1.1 Pin Description

Pin Name Type Definition

1 NC NC No function
2 MOTSWK OUT Motion detect (active low output, see Section7)
3 SDIO I/O Serial interface bi-direction data
4 SCLK IN Serial interface clock
5 LED OUT LED control
6 VSS GND Chip ground
Power supply (2.1V~3.6V) for internal power regulator, VDDA
7 VDD PWR
(1.9V) is the power regulator output.
8 VDDA PWR Analog/Digital supply voltage (1.9V)

1.2 Pin Assignment

LB RB

8
1
7
2 +Y 8
1
6 7
3 2
6
5 3
4 5
4

+X

Figure 1. Top View Pinout Figure 2. Top View of Mouse

All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission . 2
PixArt Imaging Inc.
E-mail: [email protected] V1.0, May. 2013
PixArt Imaging Inc.

PAW3205DB-TJ3T Wireless Optical Mouse Sensor

2. Block Diagram and Operation

LED LED POWER ON

DRIVE
RESET

ADAPTIVE CMOS IMAGE

FRAMERATE SENSOR
CONTROL VDD

AND POWER CONTROL

VOLTAGE REGULATOR
2.1V ~ 3.6V
POWER

MOTSWK MOTION/ VSS

WAKE UP

DIGITAL
VDDA 1.9V REGULATOR
SIGNAL
PROCESSOR
SERIAL SCLK SERIAL
INTERFACE SDIO INTERFACE
CONTROL
REGISTER

Figure 3. Block Diagram

The PAW3205DB-TJ3T is a high performance and low power CMOS-process optical mouse sensor with DSP
integration chip that serves as a non-mechanical motion estimation engine for implementing a wireless computer
mouse. It is based on new optical navigation technology, which measures changes in position by optically
acquiring sequential surface images (frames) and mathematically determining the direction and magnitude of
movement. The mouse sensor is in an 8-pin optical package. The current X and Y information are available in
registers accessed via a serial port. The word "mouse sensor", instead of PAW3205DB-TJ3T, is used in the
document.

With brand-new LED control technology, adaptive frame rate control (also known as AFC), the mouse sensor
gain extra power saving during mouse moving. The AFC servers position/speed detection and then mapping to
different frame rate. With lower frame rate, it leads to lower power consumption of the mouse sensor and LED.
The mouse sensor is featured with THREE-level AFC which is 2400/1200/800 frame per second.

All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission . 3
PixArt Imaging Inc.
E-mail: [email protected] V1.0, May. 2013
PixArt Imaging Inc.

PAW3205DB-TJ3T Wireless Optical Mouse Sensor

3. Registers and Operation

The mouse sensor can be programmed through registers via the serial port. Also, the DSP configuration and
motion data can be read from these registers. All registers not listed are reserved, and should never be written by
firmware.

3.1 Registers
Address Name R/W Default Data Type
0x00 Product_ID1 R 0x30 Eight bits[11:4] number with the product identifier
Upper Four bits[3:0] number with the product identifier
0x01 Product_ID2 R 0xDX
Lower Four bits[3:0] number with the product version
0x02 Motion_Status R - Bit field
0x03 Delta_X R - Eight bits 2’s complement number
0x04 Delta_Y R - Eight bits 2’s complement number
0x05 Operation_Mode R/W 0xB8 Bit field
0x06 Configuration R/W 0x02 Bit field
0x07 Image_Quality R - Eight bits unsigned integer
0x08 Operation_State R - Bit field
0x09 Write_Protect R/W 0x00 Bit field
0x0A Sleep1_Setting R/W 0x70 Bit field
0x0B Enter_Time R/W 0x10 Bit field
0x0C Sleep2_Setting R/W 0x70 Bit field
Image_
0x0D R/W 0x0A Eight bits unsigned integer
Threshold
Image_
0x0E R/W 0xE5 Bit field
Recognition

All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission . 4
PixArt Imaging Inc.
E-mail: [email protected] V1.0, May. 2013
PixArt Imaging Inc.

PAW3205DB-TJ3T Wireless Optical Mouse Sensor

4. Referencing Application Circuit

4.1 Power 2.7V Application Circuit, no DC/DC (with Red LED, 2.4GHz Transceiver)

Power Sensor - Buttons

PAW3205-TJ3T ENSW R0_Z2 1M
VCC_DC

1 Z2
Z_CM 3 Z2
VCC_BAT COM R0_Z1 1M
2 Z1
Z1
ENCODER
VCC_DC
BAT+1
BAT+ 1 C1
1
+
U2 1uF
BAT-1 BAT VCC_DC
1

1
1 8 C2 C3
1 VDDA
+ CPI_SW BM
NC 7 R0 1 2 CPI_SW R0 1 2 BM
S-MOTSWK 2 VDD 10uF 0.1uF
SW1 MOTSWK 6

2
VSS
BAT VCC_BAT
3 Short for direct battery S-SDIO 3
SDIO 5
2 S-SCLK 4 LED
1 SCLK D1 Red LED R1 22 B4 BR
BL 1 2 B4 R0 1 2 BR
PAW3205-TJ3T

B5 BL
BL 1 2 B5 R0 1 2 BL

RF - Nordic nRF24LE1
Power Tree
C12 22pF
2 1 XC2
Battery * 2 Sensor, LED,
X1 (series, RF
4 3 VCC_DC
1 GND OUT 2 2.1V~3.2V) (2.1V~3.2V)
IN GND
1

C11
16 MHz Cry stal
0.1uF
C13 22pF
2

2 1 XC1
S-SDIO

R2 22K
1 2
32
31
30
29
28
27
26
25

U3
50 ohm point
P0.0
XC1
XC2
P1.6
P1.5

VSS
VDD

IREF

VCC_DC
Z1 1 24 C5
2 P0.1 VDD 23 L3
3 VDD VSS 22 1 2 1 2
1

4 DEC1 ANT2 21 4.7nH

1

Z2 5 DEC2 ANT1 20 L1 1.5pF C6 C20

PROG 6 P0.2 nRF24LE1 VDD_PA 19 RESET
R0 7 PROG RESET 18 S-SCLK 6.8nH 1.0pF 1.8pF
1

C9 C7 C8 8 P0.3 P1.4 17 BM L2
2

VSS P1.3 1 2
0.1uF 0.1uF 33nF 6.8nH
Epad

2
VDD
P0.4
P0.5
P0.6
P0.7
P1.0
P1.1
P1.2
2

R8
10
11
12
13
14
15
16

33
9

/ VCC_DC
S-MOTSWK

1
2

CPI_SW

C4 C19
Z_CM

2.2nF /
1

BR
B5

B4
BL

C10
2

33nF
2

ISSP Program - Nordic

J1

VCC_DC
1 2
PROG CPI_SW
3 4
B4 RESET
5 6
BL B5
7 8

9 10

HEADER 5X2
ISSP

Figure 4. Application Circuit for 2.7V, no DC/DC

4.2 Power 2.7V Application Circuit, one DC/DC (with Red LED, 2.4GHz Transceiver)

Power Sensor - Buttons

PAW3205-TJ3T ENSW R0_Z2 1M
VCC_DC

1 Z2
Z_CM 3 Z2
VCC_BAT COM R0_Z1 1M
2 Z1
Z1
ENCODER
VCC_DC
BAT+1 BAT VCC_DC
BAT+ 1 C1
1 1N4001 / 1N4148
+
L4 220uH U2 1uF
BAT-1
D2
1
1

1 8 C2 C3
U1 1 VDDA
+ CPI_SW BM
NC 7 R0 1 2 CPI_SW R0 1 2 BM
S-MOTSWK 2 VDD 10uF 0.1uF
SW1 MOTSWK 6
C14 C16
2

BAT VCC_BAT SW VOUT S-SDIO 3 VSS

GND

3 SDIO 5
2 47uF 47uF S-SCLK 4 LED
1 SCLK D1 Red LED R1 22 B4 BR
BL 1 2 B4 R0 1 2 BR
ELM9327
PAW3205-TJ3T

B5 BL
BL 1 2 B5 R0 1 2 BL

RF - Nordic nRF24LE1
Power Tree
C12 22pF
2 1 XC2

X1 Battery * 1 DC/DC Sensor, LED,

4
GND OUT
3 VCC_DC (0.9V~1.6V) (2.7V) RF (2.7V)
1 2
IN GND
1

C11
16 MHz Cry stal
0.1uF
C13 22pF
2

2 1 XC1
S-SDIO

R2 22K
1 2
32
31
30
29
28
27
26
25

U3
50 ohm point
P0.0
XC1
XC2
P1.6
P1.5

VSS
VDD

IREF

VCC_DC
Z1 1 24 C5
2 P0.1 VDD 23 L3
3 VDD VSS 22 1 2 1 2
1

4 DEC1 ANT2 21 4.7nH

1

Z2 5 DEC2 ANT1 20 L1 1.5pF C6 C20

PROG 6 P0.2 nRF24LE1 VDD_PA 19 RESET
R0 7 PROG RESET 18 S-SCLK 6.8nH 1.0pF 1.8pF
1

C9 C7 C8 8 P0.3 P1.4 17 BM L2
2

VSS P1.3 1 2
0.1uF 0.1uF 33nF 6.8nH
Epad

2
VDD
P0.4
P0.5
P0.6
P0.7
P1.0
P1.1
P1.2
2

R8
10
11
12
13
14
15
16

33
9

/ VCC_DC
S-MOTSWK

1
2

CPI_SW

C4 C19
Z_CM

2.2nF /
1

BR
B5

B4
BL

C10
2

33nF
2

ISSP Program - Nordic

J1

VCC_DC
1 2
PROG CPI_SW
3 4
B4 RESET
5 6
BL B5
7 8

9 10

HEADER 5X2
ISSP

Figure 5. Application Circuit for 2.7V, one DC/DC

All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission . 5
PixArt Imaging Inc.
E-mail: [email protected] V1.0, May. 2013