See discussions, stats, and author profiles for this publication at: https://www.researchgate.

net/publication/324163590

Automated Packaging Machine Based on PLC

Article · May 2015

CITATIONS READS
0 2,654

2 authors:

Yousef M. Abueejela Mustafa Saad

College of Electronic Technology-Bani Walid, Libya College of Electronic Technology-Bani Walid, Libya
15 PUBLICATIONS   38 CITATIONS    12 PUBLICATIONS   58 CITATIONS   

SEE PROFILE SEE PROFILE

Some of the authors of this publication are also working on these related projects:

Inspection, Packaging and Packing Machine Based PLC View project

SCADA System of Water Pumping Stations of Bani Walid City View project

All content following this page was uploaded by Yousef M. Abueejela on 02 April 2018.

The user has requested enhancement of the downloaded file.

 IJISET - International Journal of Innovative Science, Engineering & Technology, Vol. 2 Issue 5, May 2015.
www.ijiset.com
ISSN 2348 – 7968

Automated Packaging Machine Using PLC

Alhade A. Algitta 1, Mustafa S.2, Ibrahim F.3, Abdalruof N.4 and Yousef M. 5
1,2,3,4,5
Control Engineering Dep., College of Electronic Technology,
Bani Walid 38645, Libya

[email protected]

Abstract cm × 2 cm × 3 cm). Finally, the prototype with system

This paper presents final year project prototype with the use of controller were successfully done to package 21 boxes in
programmable logic controller in automation industry for one minute, every box include 4 samples.
packaging process. The main idea of the project is to design and
fabricate a small and simple conveyor belt system, and automate
the process for packaging small cubic pieces (2 × 1.4 × 1) cm3 of
1.1 Conveyor Belt
wood into small paper box (3 × 2 × 3) cm3. Inductive sensor and
photoelectric sensor were used to provide the information to the A conveyor belt is one of many types of conveyor
controller. Electrical DC motors used as output actuators for the systems. The belt is a loop of flexible material as shown in
system to move the conveyor belts after get the orders from the Figure 1(a) used to mechanically link two or more
control system. Programmable logic controller Mitsubishi FX2n- rotating shafts, most often parallel. A belt conveyor
32MT was used to control and automate the system by ladder system consists of two or more pulleys (sometimes
logic diagram software. The experimental result of the prototype referred to
was able to fully automate the packaging system. This results as drums), with an endless loop of carrying medium that
show that the machine were done to package 21 boxes in one
rotates about them as shown in Figure 1 (b). One or both
minute. In addition, the results obtained show that the system
able to decreases product time, and increase product rate as of the pulleys are powered, moving the belt and the
compared with traditional manual system. material on the belt forward. The powered pulley is called
the drive pulley while the unpowered pulley is called the
Keywords: Packaging Machine, Automated, PLC, Switches, idler pulley.
Inductive Sensor, Photoelectric Sensor. There are two main industrial classes of belt conveyors;
Those in general material handling such as those moving
boxes along inside a factory and bulk material handling
1. Introduction such as those used to transport large volumes of resources
and agricultural materials, such as grain, salt, coal, ore,
Industry automation becomes the global trend in sand, overburden and more [6].
manufacturing, packaging process is one of the most uses
in industry; more and more companies are switching to
automation. This project is devoted to the use of automatic
control system in process machine system; the control
system will play a major role in control on all parts of the
project. This project report is about design and fabricate
an automated packaging machine system. Electrical DC
motors control were used as actuators for the entire
process to move the upper and lower conveyor belts, and
the sensors used to feed the control system by system Fig. 1 (a) Belt Type, (b) Conveyor Belt with Pulley.
information.
Conveyor belt used for transporting samples from
location to another one, which would be packaged into a 1.3. Packaging
specific paper boxes later. The control system for the
hardware project is to be controlled by the Mitsubishi Packaging is the technology of using conveyor belts for
FX2n-32MT programmable logic controller (PLC) device. enclosing or protecting products (food, wood, and
Ladder logic diagram for programmable logic controller material) for storage, pack objects together into containers,
were used for control the actual prototype for the sale, and use. Packaging also refers to the process of
experimentation. The whole system executes to package 4 design, evaluation, and production of packages. Packaging
wood samples (2 cm × 1.4 cm × 1 cm) into paper boxes (3 can be described as a coordinated system of preparing

282
 IJISET - International Journal of Innovative Science, Engineering & Technology, Vol. 2 Issue 5, May 2015.
www.ijiset.com
ISSN 2348 – 7968
goods for transport, warehousing, logistics, sale, and end There are three different functional types: opposed
use. Packaging contains, protects, preserves, transports, (through beam), retro-reflective, and proximity sensing
informs, and sells [7]. (diffused), figure 3 shows one of Photo types [8].

2. Components Selection and Hardware

Structure
The Automatic Packaging Machine system is a
combination of electronic, electrical and mechanical parts, Fig. 3 Photoelectric Sensor Sample.
Figure 2 shows the whole system proposed.
• Input Devices are devices used to gather information
about the system, which consists switches (toggle In the project prototype, the photoelectric sensor is
switch) and sensors (photo and inductive sensor), in placed at the upper belt to sense and count the samples
order to feed the controller (PLC) by an information before dropping them in the box as shown in Figure 4
about the belts status and objects. below.
• The controller, which is the main element that operate
the whole system, by using the information from the
sensors to take the counting and movement decision
before sending the orders to the output devices by the
actuators and the relays.
• Output Devices are the actuators that converts an
electrical signal into mechanical movement; the
principle types of actuators are relay, solenoid, and
motors.
PLC
Fig. 4 Photoelectric Sensor Setup on the Project.

. 2.1.2. Inductive Proximity Sensors

Inductive sensors use currents induced by magnetic

fields to detect nearby metal objects. All of inductive
Fig. 2 Automated Packaging System. sensors consists of four basic elements; the oscillator,
which produces the electromagnetic field, the coil, which
generates the magnetic field, the detection circuit, which
2.1 Sensors detects changes in the field when an object enters it and
A sensor is a device that measures a particular the output circuit which produces the output signal as
characteristic of an object or system. Some sensors are shown in figure 5 [1].
purely mechanical, but most sensors are electronic,
returning a voltage signal that can be converted into a
useful engineering unit. Sensors are used in everyday
objects such as touch-sensitive elevator buttons (tactile
sensor) and lamps, which dim or brighten by touching the
base. There are also innumerable applications for sensors,
Fig. 5 Inductive Proximity Sensor Structure [9].
which include cars, machines, aerospace, medicine,
manufacturing and robotics [3].
The inductive sensor was installed above the lower
2.1.1 Photoelectric Sensor conveyor belt (about 3 cm) and in front of the particular
upper belt to sense the coming boxes of the samples for
A photoelectric sensor, or photo eye, is a device used to packaging. This sensor can be able to sense from (0.5 mm
detect absence, or presence of an objects by using a light to 5 mm) and it sense iron only (so that metal sheets were
transmitter, often infrared, and a photoelectric receiver. used to cover the boxes) as shown in Fig. 6 below.
They are used extensively in industrial manufacturing.

283
 IJISET - International Journal of Innovative Science, Engineering & Technology, Vol. 2 Issue 5, May 2015.
www.ijiset.com
ISSN 2348 – 7968

2.3 . Actuators
Actuation defines as the result of a direct physical action
on the process, such as drilling a work piece or rotate the
object from side to another side by rotating the upper
rotary disk.

2.3.1 DC Motor
DC motors have been used in industrial applications for
years. Coupled with a DC drive, DC motors provide very
precise control. DC motors can be used with conveyors,
Fig. 6 Inductive Sensor Setup on the Project.
elevators, extruders, marine applications, material
handling, paper, plastics, rubber, steel, and textile
applications [2,3].
2.2 . Switches As shown below Figure 8, two DC motors were
installed on the project; one of them mounted with a
Switches are electrical or electronic contact devices used pulley to rotate the upper belt (Y1), and the other one,
to turn (ON) or (OFF) the flow of electricity through a mounted with a pulley to rotate the lower belt (Y0). The
circuit. Switches are essential components in almost all the two motors used to do next tasks:
electronic devices used today. Switches require another 1. The lower DC motor starts first to bring empty boxes
device or action (Force) to change their state from open to at desired position.
close or close to open. Switches might operate manually or 2. The upper DC motor starts after the box reach desired
mechanically. position, to bring some samples for packaging into the
• Manually Operated referred to types operated by hand, box.
which the operator must do an action, in order to start,
stop or reverse the state. Manually switches such as
(toggle and pushbutton switches).
• Mechanically Operated referred to switches those
controlled automatically (Mechanically) by factors such
as pressure, position, flow, or temperature. These
include (limit switch, inductive limit switch) [1].

2.2.1 Toggle Switch

Toggle switch is operated manually by external action
(force) and come in two types:
• Momentary: where the contacts are operated only
while the actuator is operated. Sometimes referred to Fig. 8 Upper and Lower DC Motors Installation.
as spring return.
• Non-Momentary (Latching): sometimes called on-off
or, with a button actuator, where the contacts lock in 2.4 Relays
one position when the button is pressed then released Relays are simple switches operated both electrically and
and only change back when the button is pressed a mechanically . Relays consists of an electromagnet and set
second time. [4][5]. In the project, the switch is used of contacts .There are also other operating principles for
for starting up and shutting down the system by the its working which differ according to their applications,
designer as shown in figure 7 below. Figure 9 shows type of electro-mecanical relays used in
the project [3].

Fig. 9 Type of Relays.

Fig. 7 Toggle Switch Used.

284
 IJISET - International Journal of Innovative Science, Engineering & Technology, Vol. 2 Issue 5, May 2015.
www.ijiset.com
ISSN 2348 – 7968
Figure 10 shows the mechanical relays used on the project
as interface between the PLC outputs and DC motors
inputs.

Fig. 12 Indicators.

Fig. 10 Relay's Setup on the Project.

2.6 Mechanical Structure and Design
A solid-state relay is an ON-OFF control device in which The project prototype designed and fabricated with
the load current is conducted by one or more semi metal rods by dimensions 80cm × 80cm (length x width)
conductors. Like all relays, the SSR requires relatively low as shown in
control circuit energy to switch the output state from OFF Figure 13
to ON. Since this control, energy is very much lower than below in order
the output power controllable by the relay at full load [7]. to carry the
In this prototype, since the photoelectric output voltage is completely
very small, we used them as interface between the output packaging
of the sensors and the input of PLC. Figure 11 shows the components.
SSR positions on the prototype.

Fig. 13 Project Prototype Main Base.

Conveyors are a strip of belt mounted on pulley at two

Fig. 11 Solid State Relay Installation. ends, driven by one or two of the pulleys. In the prototype
as shown in Figure 14, two belts were used as upper and
lower belts; the upper belt is 67 cm length with 4.6 cm
2.5 Indicators width installed on the 67 cm rod. The other belt with is 72
cm length with 4.6 cm too, installed on the 72 cm rod
Indicators are used to monitor the system operation or
condition and the telecommunication and electrical circuit Fig. 14 Upper and Lower Belts Setup on the Project.
for indicator signal, accident signal, fault signal and other
indicator signals [4].
In our project as shown in Figure 12, we have chosen
three types of indicators in order to monitor different
operations, this indicators are:
• Green indicator: To indicate and show system running
state.
• Yellow indicator: To indicate lower belt moving state.
• Red indicator: To indicate upper belt moving state.

285
 IJISET - International Journal of Innovative Science, Engineering & Technology, Vol. 2 Issue 5, May 2015.
www.ijiset.com
ISSN 2348 – 7968
Two DC motors (12 volts) mounted with main pulley
for each to derive and rotate the belts (Upper and Lower
belts) as shown in Figure 15, Red arrows indicate belt
direction moving.

Fig. 18 Block Diagram of the System.

Fig. 15 DC motors with pulley Installation.  Toggle Switch: It have two wires connected as
sourcing to the PLC one of the wirers is connected to
24 V DC, while the other wire is connected to 0VDC.
Figure 16 below shows the pulleys and motors dimensions
on the prototype.
 Inductive Proximity Sensors: The first wire of
inductive proximity sensor is connected to X0 at the
PLC and the other wire is connected to 0 VDC.
 Photoelectric Sensor: The first wire of photoelectric
sensor is connected to X1 at the PLC and the other
wire is connected to 0 VDC.
 Lower DC Motor: Since the DC motor works under
5V and the PLC gives 24VDC, then 24VDC relay
used. The lower DC motor is connected to (Y1) in the
Fig. 16 Pulley and DC Motor in the Prototype.
PLC.
 Upper DC Motor: since the DC motor works under
5V and PLC gives 24VDC, then 24VDC relay is used.
Figure 17 below shows the size and dimensions of the The upper DC motor is connected to (Y2) in the PLC.
boxes and samples which used in the prototype. Figure 19 below shows the wiring of the whole component
of the prototype with the PLC

Fig. 17 Size of Boxes and Samples.

3. Block Diagram and Wiring the System

The block diagram of the proposed system is shown in
figure 18, which consists of three inputs (toggle switch ,
photo sensor, inductive sensor) to provide the control by
system state. Also the system consist of three output (the
dc motor, indicators) Fig. 19 Wiring of PLC.

286
 IJISET - International Journal of Innovative Science, Engineering & Technology, Vol. 2 Issue 5, May 2015.
www.ijiset.com
ISSN 2348 – 7968

3.1 Programmable Logic Controllers (PLC) Photoelectric Sensor (X1): It used to count the dropped
samples during packaging process.
Technical specifications of PLC Mitsubishi FX2n- Relays: the works as interface between the motors,
32MT on the Table 1 [2]. photoelectric sensor and the PLC.
Table 1: Technical Specifications of Mitsubishi PLC Indicators: were used to light different colors to show
General features system states.
Max .number inputs/outputs Power Supply: It feed the system with different voltages.
16
Power supply 100-240 VAC
The prototype experimental testing and running divided
Output type Transistor
to next steps as following:
Power consumption [W] 30 V A
Step one:
Weight [Kg] 0.65 When the toggle switch pressed ON, the system start
Dimensions (WxHxD) [mm] 136x90x87 ruining by moving the lower belt by DC motor (Y0),
which carrying and bring the empty boxes, as the empty
box reach the inductive sensor (X1) as shown in Figure
21, that the inductive sensor will activate and send signal
4. Experimental Results and Discussions back to the PLC to stop the lower belt moving. In the same
time when the system start running, the green indicator
Figure 20 shows the whole system prototype for the
lights ON, to inform the operator system states. Although,
automated packaging machine, as shown in the figure, it
the yellow indicators lights ON for lower belt moving.
consists of sensors (inductive and photoelectric), actuators
(two DC motors, two mechanical relays and solid-state
relay), and indicators (red, green, yellow), PLC, power
supply, boxes, samples.
Each component have a specific function to perform,
which can be explained as follows:
Toggle Switch: was use as main switch to start up, and
turn off the Packaging system.
Lower Motor (Y0): it is responsible for the movement of
the lower conveyor belt, to bring empty boxes in sequence
to the desire location.
Inductive Sensor (X0):This sensor has two main
missions, the first one is to detect the empty boxes as Fig. 21 Inductive Sensor Activated as the box be in location.
arrival at the desired location, the second one is to stop the
lower belt and activate the upper belt to drop the samples Step two:
into the box. As the box, reach the desired location, the lower belt stop
Upper Motor (Y1): it is responsible for the movement of moving and the upper belt start moving. Upper belt starts
the upper conveyor belt, to bring the cubic samples in to bring the samples one by one and drop them into the
sequence to package them into the box. box. This operation running until four samples.
Meanwhile, the red indicator lights on to show that the
system is packaging. Figure 22 show packaging operation
of the samples.

Fig. 20 Packaging Machine Prototype. Fig. 22 Packaging Operation.

287
 IJISET - International Journal of Innovative Science, Engineering & Technology, Vol. 2 Issue 5, May 2015.
www.ijiset.com
ISSN 2348 – 7968
The photoelectric sensor used to count the samples 5. Conclusion
while packaging, when the box fill by four samples, the
sensor give information back to the PLC to stop the upper An automated packaging machine prototype using PLC
belt and bring another empty box to package it. Mitsubishi FX 2N has been successfully design,
After the photoelectric sensor, count four samples, the constructed and implement based on control system
upper conveyor belt stop moving and the lower conveyor concepts. Mitsubishi ladder diagram applied for the
start moving to carry the filled box away and bring another programming and operation of the presented prototype, in
empty box to package it with another four samples. Figure which the operation is passes through two stages, carrying
23 below shows the final operation of the packaging. empty boxes to desired location, and packaging the
samples into the boxes. The experimental prototype tested
to improve the automation processes with the use of the
PLC ladder diagram. The packaging prototype was done
to package four sample per a box in very short time. From
the experimental result, the automatic packaging machine
was able to package 1260 boxes per one hour, otherwise
the manual packaging able to package just 840 boxes at
the same time.

6. References
[1] Yousef M. Abueejela, A. Albagul, Ibrahim A. Mansour and
Obida M. Abdallah, " Automated Drilling Machine Based on
PLC", in International Journal of Innovative Science,
Engineering and Technology, Vol. 2 Issue 3, March 2015.
Fig. 23 Carrying filled Box and Bring Another. [2] A. Albagul, K. Alsharef, M. Saad, Y. Abujeela, "Design and
Fabrication of an Automated Multi-level Car Parking
System", in Manufacturing Engineering, Automatic Control
and Robotics, 2013.
4.1 Product Rate of the System [3] H . karnataka, "PLC controlled low cost automatic packing",
International Journal of advanced mechanical engineering,
The experimental results for the automatic and manual vol . 4, no .7, PP.803-811,2014.
operation shows different products rate as shown in Table [4] Ibrahim M. and Obida A., "Automated Drilling
4.2 below. Machine Based on PLC" B.Sc. project, Dept. Control
Eng. College of Electronic Technology Bani Walid, 2015.
[5] D. Shetty and R. Kolk, Mechatronics System Design. India,
Table 4.2: System Product Rate
2004.
Manual Automatic [6] Wikipedia. “Conveyor Belt”, Wikipedia.org. [Online].
Product Time Modified: 14 March 2015, at 11:21].
Packaging Packaging [7] Wikipedia. “Packaging and labeling”, Wikipedia.org.
[Online]. Available
One Minute 14 Boxes 21 Boxes http://en.wikipedia.org/wiki/Packaging_and_labeling
[8] (2015.feb.23)."photoelectric sensors theory of operation"
One Hour 840.00 1260.00
[online]. Available http://
One Day ( 8 www.enm.com/products/content/seimens/training/seimens_cou
6720.00 10,080.00 rses. [Accessed: feb .29 ,2014].
hours) [9] P. Frank ,Electric motors and control systems. USA,
McGraw-Hil, 2010.
One Week (5
33,600.00 50,400.00
working days)
One Month 134,400.00 201,600.00

288

View publication stats