TM-610 SINOTIMER

1.Introduce

-Industry first utility function:

Built-in calendar, 10 holiday times can be set in a year
EXT port(extended length can reach 100 meters)
16 groups procedure controls(ON/OFF)
32 pulse controls(can be used for bell or on trigger-start equipment)
www.sinotimer.com

Countdown function
-Can be programmed, or manually controlled for easy use
-Imported digital chip, intelligent and stable system
-LCD display, LED work instruction
-Built-in lithium battery, when a power failure, data will not be lost and timer
will travel time as usual and be in auto-sleep
-Key parts adopt imported components
-Standard width: 17.5mm
-Standard installation with Din 35mm
-Widely used in industry, house, building, corollary equipment, etc.

2. Technical data

Rated voltage: 220-240VAC load capacity: AC250V 16A COSφ=1

Mains frequency: 50Hz Load Inductive : AC250V 10A COSφ=0.6

Procedure setting: 16 on/off program EXT switch: cable length≤100m

Pulse program: 32 channels Contact point: 1group
duration:1-99sec
Holiday program: 10 Contact resistance ≤100mΩ
TM-610 Digital time switch for DIN rail between contacts:
Countdown: duration: Insulation resistance ≥100MΩ
1-99min 59sec between contacts:

Electrical life: 105 times Working temperature: -10 ~ +50 OC

Mechanical life: 107 times Ambient humidity: 35-85% RH

Power reserve: 3Years Storage temperature: -10 ~ +60OC

Power: ≤ 3VA Weight: ≤ 90g

2 www.sinotimer.com

SINOTIMER TM-610 TM-610 SINOTIMER

3.Wiring diagrams
Program setting interface chart

L N After press Res Key

L N
Unit:mm Initial interface
! prog
*
Cannot be used at the same time
*
Press +/- key select
max88.0

press OK again enter countdown setting

*
45.5

Press “OK” Key

Press +/- key select
Menu ok Menu ok press OK again enter pulse setting
_ Res
_ Res
+ + Auto
Press “Menu” Key to select Press +/- key select prog
Press OK again to enter the clock setting press OK again enter program setting
1 EXT
External
Switch 1 EXT 6 *
Press +/- key to select “Man”
2 3 press OK again enter funtion setting
2 3
Load

N Cock EXT Auto

L max18.0 interface
L1 max66.0 6

1 2 3

Auto Auto
4.Setting and operating EXT EXT Auto Auto

2 6 6 6 6
Notes: Clock set 4 state control EXT:External control Holiday 16 program 32 pulse Countdown
interface settings interface settings interface settings interface setting interface setting interface setting interface
1. Press “Menu” and “-” for 3 seconds, procedures will be closed but all Auto on/on
Auto oFF/oFF
former setting will be lost; press “Res”, all procedures will be cleared.
2. In any setting screen but no any operation within 30 seconds,
procedure will back to clock screen automatically, and will not save Date and time setting built-in calendar, set Year, Mouth, Hour and
Minute respectively.
setting data.
3. Duing to built-in lithium battery, you can install timer in distribution 1. Press “Menu” until “ ” flashes, then press “OK” into clock setting interface,
box or control circuit after setting procedures. Mark Year will flash.
2. Press”+/-“ to required year ,then press “OK” to confirm .About setting mouth,
day ,hour and minute ,same operation as setting year.
3. After finishing setting date and time, press “Menu” to exit and complete this
setting.

Note: After the date is set, week will be self-synchronizing

www.sinotimer.com 3 4 www.sinotimer.com
SINOTIMER TM-610 TM-610 SINOTIMER
1. Program/ pulse/ countdown function setting 2. pulses control program setting (user can set number of pulse
control as requires, at most 32 channels)
Notes: After press “Res” key,the following three kinds of programs can
only select one of them and cannot be used at the same time A: Press “Menu” in clock display screen. When marker flashes, press
OK into group 1 setting screen icon.
1.Program setting(user can set program switch number as required
at most 16 groups) B: Press “Menu” then marker hour flashes icon.
A: Press “Menu” in clock screen , when “prog” flashes, press “OK” to C: Press “+/-“ to set hour and press “OK” after finishing . set minute and
confirm and enter into one setting screen, 01 on flashes. press “OK” to confirm .

B: Press “OK” into time setting, marker hour and minute flashes icon D: Program enters into week setting screen, and setting ways please follow
program setting.
C: Press “Menu”, then marker hour flashes icon.
E: Press “+/-“ to set pulse control time ,and the duration range is from 1-99
D: Press “+/-“ setting hour and press “OK” after completing then same sec ,after finishing, press “OK” into 2nd setting or press Menu to confirm
and exit.
setting for flashing minute and press “OK” after completing.
3.Countdown setting (user can set countdown time, at longest time
E: When program enters into week setting screen , marker 1(Monday) is 99 minutes and 59 seconds )
flashes .If need to open 1 (Monday),press “+” to open and copy to
marker 2 (Tuesday),or press “-” to delete 1(Monday) , again to press A: After press “Rst” Key, press “+/-” key , when marker flashers, press
“+” to 2(Tuesday),You can set week in turn after finishing press “OK” OK into countdown.
to confirm and program will enter into setting screen of close time.
B: Press “+/-“ to set minutes and press “OK” after seconds flashes .
Attention:
After finishing week setting, open-needed week days will be shown in C: Press “+/-“ to set seconds and press “Prog” completing and exit.
the screen.
D: Press “+” and “-” Key, to select Auto OFF state.
If all week days need to be open ,press “OK” and enter into setting
screen of close time when marker Monday flashes. E: Press “OK” and “+” Key, can to start and close countdown.
F:Repeat step b to e ,and finish setting close time and week .Press “OK”
into 2nd setting or press Menu to confirm and exit.
EXT
T
T

www.sinotimer.com 5 6 www.sinotimer.com

SINOTIMER TM-610 TM-610 SINOTIMER

Man function setting (4 state control ways /EXT setting /holiday setting ) 3.Holiday setting (can set 10holiday times within 1 year and every
group of ON/OFF setting is required respectively)
Press ”Menu” until remark Man flashes, press OK into Man function setting
screen, press “+/-“to choose required functions ,then press OK into A: Press “+/-” choosing “ ”,then press ok to confirm.
subprogram setting screen.
B: Press “+/-” choosing ON/OFF
1.Control ways setting (Auto ON/ON/Auto OFF/OFF)
C: Press “Menu” into year setting screen (set the start time of holiday first
A) Press “+/-“ to choose remark Auto, then press “OK” to confirm
and the end time second)
B) Remark OFF Auto flashes press “+/-“ to choose one of control ways
D: Press “+/-” choosing choosing required year ,then press OK into date
(Auto ON/ON/Auto OFF/OFF) ,and press “Menu” to exit after finishing
screen.
setting.
E: Press “+/-” choosing choosing required date ,then press OK into setting
OR: press “+” and “-”, can cycle setting Auto ON/ON/Auto OFF/OFF
screen of holidays (dates off) automatically.
at 4 state.
F: Repeat step b-e ,and the system will enter into next holiday setting after
setting , or press “Menu” to exit to time screen.
2.EXT setting .(if need this function ,external control switch is
required ,and wiring method id shown in the diagram.

A) Press “+/-“ to choose remark EXT, then press “OK” to confirm

B) Press “+/-“ , there will be 2 selections :OFF EXT /ON EXT. press
”Menu” after finishing choosing.
Notes:
A) There will be remark EXT after you set to EXT ON .But it is valid for
Notes:
EXT control switch in the state of Auto on or Auto OFF. Do not use this product in the places with dustiness, etchant gas,
B) In the state of on or off ,the equipment will be forced to ON or OFF . direct sunlight or rain.
If not followed by setted procedures ,it will be not valid .Only running Please store and use in the places with rated voltage, specific
timer in the state of Auto on or off , EXT switch is valid. temperature and humidity
If design and specification of product are subject to change, will not
C) When setting EXT off ,EXT input port is not valid ,timer will run by
further notice.
setted procedure or pulse .When setting EXT on , EXT input port is
valid.There is no execution of setting procedures or pulse when EXT
switch closes setting procedures or pulse execute when EXT switch
opens.

www.sinotimer.com 7 8 www.sinotimer.com