A.

SCOPE 範疇
This specification applies speaker, KDMG10008C-03
此規格書適用於喇叭 ,KDMG10008C-03

B. SPECIFICATION 規格
No. Item Symbol Unit Specification Condition
Dimension
1 mm φ10.0 x 2.9
尺寸
Power Rating
2 W Rated. 0.3/ MAX. 0.5
功率
Impedance
3 Ω ohm 8 ± 15% At 1.5KHz 1.0V
阻抗
Resonance Frequency
4 Fo Hz 1200 ± 20% At ,1.0V
低音諧振
Output S.P.L. 86 ± 3dB(0.3w/10cm) At 1.0k,1.2k,1.5k,2.0kHz
5 dB
音壓位準 72 ± 3dB(1w/1m) (Average figures)
Frequency Range
6 Hz Fo---20K
有效頻寬
Distortion
7 % 10 Max. At 1.5kHz , 0.3W
失真
Voice Coil
8 mm --------
音圈
Magnet
9 mm φ5.3 x 1.0 Nd-Fe-B (銣鐵錋)
磁石
Flux Density
10 Gauss
磁通密度
Operating temp.
11 ℃ - 20 ~ +55
操作溫度
Not be audible at 1.55V sine
Buzze & Rattle wave between Fo ~ 20KHz
12 輸入 1.55V 正弦波從 Fo 到
異常音
20KHz 之間無異常音
Weight
13 g 0.6
重量
Material
14 Metal
材質
Environmental Protection
15 Regulation ROHS
環保法規

志豐電子股份有限公司 KINGSTATE ELECTRONICS CORP 2/6 KDMG10008C-03

C. TYPICAL FREQUENCY RESPONSE CURVE 頻率響應曲線

志豐電子股份有限公司 KINGSTATE ELECTRONICS CORP 3/6 KDMG10008C-03

D. APPEARANCE DRAWING 外觀尺寸圖

8Ω
0.3W

CUSTOMER'S CAP
SOLDERING POINT

Tol: ± 0.3
Unit: mm
E. MEASUREMENT CIRCUIT 測量線路

志豐電子股份有限公司 KINGSTATE ELECTRONICS CORP 4/6 KDMG10008C-03

F. MECHANICAL CHARACTERISTICS 機械特性
No. Item Test condition Evaluation standard
No obstacle to be harmful
Speaker shall be measured after being applied vibration of
amplitude of 1.52mm with 10 to 55Hz band of vibration to normal operation;
Vibration Test damages, cracks, rusts and
1 frequency to each of 3 per-pendicular directions for 2 hours.
振動測試 distortions.
振動週波數 10∼55Hz、全振幅 1.52mm 於 X.Y.Z 3 個方向,
各 2 小時 Should not be audible at
1.55V sine wave between
Drop the speakers contained in normal box onto the board Fo ~ 20KHz
Drop Test 測試後無任何障礙防礙正常
2 40mm thick 10 times from the height of 75cm
落下測試
將揚聲器置於盒中, 自 75 公分高度落在 40mm 木板上共 10 次 操作.且在輸入 1.55V 正弦波
從 Fo 到 20KHz 之間無異常音

G. ENVIRONMENTAL TEST 環境試驗

No. Item Test conditions Evaluation standard
High temp. Test After being placed in a chamber at +55℃ for 96 hours
1
高溫測試 置於+55℃環境中 96 小時
Low temp. Test After being placed in a chamber at -20℃ for 96 hours. Being placed for 6 hours at
2
低溫測試 置於-20℃環境中 96 小時 +25℃, speaker shall be
After being placed in a chamber at +40℃ and 90±5% RH measured. No obstacle to
Humidity test be harmful to normal
3 relative humidity for 96 hours.
相對濕度測試 operation; damages,
置於+40℃, 相對濕度 90±5%環境中 96 小時
cracks, rusts, etc.
The part shall be subjected to 5 cycles. One cycle shall be Should not be audible at
consist of: 1.55V sine wave between
單體承受溫度循環測試 5 次,其循環內容如圖示: Fo ~ 20KHz. Fo should
meet initial one. S.P.L.
+55℃
deviation of unit should be
within ±3dB
經測試後, 靜置於+25℃
Temp. cycle test +25℃
4 （室溫）環境中 6 小時後, 測
溫度循環測試 試後無任何障礙防礙正常操
-20℃
作.且在輸入 1.55V 正弦波從
0.5 0.5 Fo 到 20KHz 之間無異常音.
2hrs hr 1hr hr 2hrs Fo 與原規格值相同輸出音壓
變化量在±3dB 內
6hrs

志豐電子股份有限公司 KINGSTATE ELECTRONICS CORP 5/6 KDMG10008C-03

H. RELIABILITY TEST 信賴性試驗
No. Item Test conditions Evaluation standard
No obstacle to be harmful
to normal operation;
damages, cracks, rusts,
etc.
Should not be audible at
1.55V sine wave between
Fo ~ 20KHz. Fo should
Load test 0.3W white noise is applied for 24 hours meet initial one. S.P.L.
1
連續負荷 輸入功率 0.3W, 連續操作 24 小時 deviation of unit should be
within ±3dB
測試後無任何障礙防礙正常
操作.且在輸入 1.55V 正弦波
從 Fo 到 20KHz 之間無異常
音.Fo 與原規格值相同輸出
音壓變化量在±3dB 內
TEST CONDITION.
Standard Test Condition : a) Temperature : +5 ~ +35℃ b) Humidity : 45-85% c) Pressure : 860-1060mbar
一般測試條件 : a) 溫度 : +5 ~ +35℃ b) 濕度 : 45-85% c) 氣壓 : 860-1060mbar
Judgement Test Condition a) Temperature : +25 ± 2℃ b) Humidity : 60-70% c) Pressure : 860-1060mbar
爭議時測試條件: a) 溫度 : +25 ± 2℃ b) 濕度 : 60-70% c) 氣壓 : 860-1060mbar

I. PACKING STANDARD 包裝規格

Each minimum package unit of products shall be in a carton box and it shall be clearly marked
with Part Number, quantity and outgoing inspection number. There shall be no mechanical
damage on products during transportation and/or in storage.
外箱須標示最小包裝單位, 並註明產品型號、數量及檢驗批號.,必須是物品儲藏或運輸過程中可
防止造成損傷的包裝.

志豐電子股份有限公司 KINGSTATE ELECTRONICS CORP 6/6 KDMG10008C-03