Scribd
Upload
144 views1 page

Afm Er80s-D2 en

AFM ER80S-D2 is a low alloy steel wire for welding carbon and low-alloy steels. It contains 0.5% molybdenum for increased strength and deoxidizers like manganese and silicon to control porosity during CO2 shield welding. It produces radiographic quality welds with excellent bead appearance for both ordinary and difficult steels. The wire also exhibits good out-of-position welding characteristics and is suitable for multiple-pass welding of higher strength steels in as-welded and post-weld heat treated conditions. Standard sizes range from 0.035 to 1/6 inches in diameter.

Uploaded by

Valentin Hernández Triano
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
144 views1 page

Afm Er80s-D2 en

AFM ER80S-D2 is a low alloy steel wire for welding carbon and low-alloy steels. It contains 0.5% molybdenum for increased strength and deoxidizers like manganese and silicon to control porosity during CO2 shield welding. It produces radiographic quality welds with excellent bead appearance for both ordinary and difficult steels. The wire also exhibits good out-of-position welding characteristics and is suitable for multiple-pass welding of higher strength steels in as-welded and post-weld heat treated conditions. Standard sizes range from 0.035 to 1/6 inches in diameter.

Uploaded by

Valentin Hernández Triano
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

AFM ER80S-D2

Low Alloy Steel Wire

Classifications
AWS A5.28 AWS A5.28M
ER80S-D2 ER55S-D2
Characteristics and typical fields of application
AFM ER80S-D2 contains 0.5% molybdenum for increase strength and high level of deoxidiziers (Mn and Si) to control porosity
when welding with CO2 as the shielding gas. It will give radiographic quality welds with excellent bead appearence in both
ordinary and difficult-to weld carbon and low-alloy steels. AFM ER80S-D2 exhibits excellent out-of-positin welding
characteritics with the short circuiting and pulsed ar processes. The combination of weld soundness and strength makes AFM
ER80S-2 suitable and multiple-pass welding of variety ofcarbon and low-alloy,higher stregth steels in both the as welded and
postweld heat-treated conditions.

Weld metal chemical analysis in (%)

C Mn Si P S Ni Mo Cu Fe

0.07 - 0.12 1.60 - 2.10 0.50 - 0.80 0.025 0.025 0.150 0.40 - 0.60 0.50 Balance
All values area consideradered maximum, unless otherwise noted.

Mechanical properties under CO2 shielding gas

Tensile strength Yield strength Elongation Impact energy

MPa MPa % Joules


550 470 17 27 (-30 °C)
Preheat and interpass temperature
275 - 325 °C. It does not require a post weld heat treatment
Welding positions

Standard Sizes
0.035" 0.9 mm 3/32" 2.4 mm

0.045" 1.2 mm 1/8" 3.2 mm

1/16" 1.6 mm 5/32" 4.0 mm

Due to the continuous improvement of consumables, we reserve the right to change the information contained in this data
sheet without notice. Details concerning the application are for the purpose of guiding the user . The user is fully responsible
for the proper use of these products to comply with the standards , specifications , maintenance procedures and building
codes , manufacture , assembly or repair applicable.

You might also like