0% found this document useful (0 votes)
641 views3 pages

JDM A26 - Rev. 03-1988

Uploaded by

Romulo Eduardo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
641 views3 pages

JDM A26 - Rev. 03-1988

Uploaded by

Romulo Eduardo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

/:;EIS

. . .. . . . . .. . . .

= 4Yao~4kl ooasbq~ ~~q - “’”” ‘- - - . .. . . . -

i,, ,. John Deere Standard

JDM A26
- Specification for Steel Pipe
1. SCOPE

JDM A26 specifies the requirements ot welded and seamless standard weight (STD), extra strong (XS), and double
extra strong (XXS) black steel pipe, and standard weight (STD) hot-dipped, zinc-coated (“galvanized”) steel pipe,
of standard dimensions conforming to ANS1/ASME B36.1 OM; and welded light wall (LW) schedule 10 black steel
pipe of dimensions conforming to ASTM Al 35.

JDM A26 steel pipe, also called “pressure pipe,” is intended for conveying liquids or gases in fluid lines with
connections by mechanical couplings or by welding. The suitability of steel pipe for various purposes is dependent
on its dimensions, properties, and conditions of service. It is not intended for use in structural amlications.
.. For
“structural pipe” see JDM A22.

2. DESIGNATIONS

Steel pipe is designated by the specification, the grade, the nominal size, and the description.

The specification and grade of steel pipe conforming to JDM A26 may be designated in one of two ways:

● by the JDM number from Table 1.


● by the ASTM specification number and the class, type, and grade, as required, from Table 1.

The nominal size of steel pipe is designated in one of three ways:

. by the nominal pipe size (NPS designation) and the identification of the series (weight class) and/or schedule
number.
● by the nominal pipe size (NPS designation) and the nominal wall thickness in inches.
● by the nominal outside diameter and wall thickness, in inches or millimeters.

The standard “inch nominal sizes” or “nominal pipe sizes” (NPS designations) and their nominal outside diameters
are specified in ANS1/ASME B36.1 OM.

Except for JDM A26E, the identifications of the series (weight classes), schedule numbers, and nominal wall
thicknesses are specified in ANS1/ASME B36.1 OM. For JDM A26E light wall (LW) schedule 10 pipe, the nominal
wall thicknesses are specified in ASTM Al 35.

Issued: Feb 52 Revised Mar S8 Term Cod= Design Controk DT Page 1 of 3


Supersede% Aug 79
Readers are reminded that the information and ideas conveyed in this standard, as well as the physical document itself, are the property of Dcore
& Company. This material should not be divulged outsido of the Corporation witflout authorization.
Deere & Company Engirmcring Standards Department, John Deere Roadr Moline, Illinois 61265. Unpublished--All rights reserved under the copyright
laws.
.. . ... . . . . . .. .
E 4;NlJLIL OO05b78 b50 =

2. DESIGNATIONS (continued)

DESIGNATION EXAMPLES:
-“
JDM A26A2 NPS 3/4 STD Steel Pipe
JDM A26A2 NPS 3/4 x .113 Wall Steel Pipe
JDM A26A2 26.7 mm O.D. x 2.87 mm Wall Steel Pipe
ASTM A53, Type E, Grade B, NPS 3/4 STD (Schedule 40), Plain End, Black, Electric-Resistance-Welded Steel
Pipe

3. REQUIREMENTS

The following requirements apply to steel pipe ordered by the JDM numbers described in Table 1.

Unless otherwise specified, the standard provisions of the latest relevant ASTM standards shall apply for all points
not taken up in this JDM specification. Supplementary and special requirements, if any, shall be as specified by
the purchaser.

The pipe shall conform to the ASTM specification and description given in Table 1. Unless otherwise specified
by the purchaser, options given in Table 1 are at the choice of the supplier.

The size of the pipe maybe designated in either US customary units or S1units. In either case, by agreement between
the purchaser and supplier, the permissible variations in dimensions and weight may be applied to the standard
nominal dimensions and weights in either US customary units or S1 units.

4. REFERENCES

ANS1/ASME B36.1 OMWelded and Seamless Wrought Steel Pipe

ASTM A53 Specification for Black and Hot-Dipped, Zinc-Coated Welded and Seamless Steel Pipe

ASTM A135 Specification for Electric-Resistance-Welded Steel Pipe

ASTM A139 Specification for Electric-Fusion (Arc) -Welded Steel Pipe (Sizes 4 in. and Over)

ASTM A714 Specification for High-Strength Low-Alioy Welded and Seamless Steel Pipe

JDM A22 Specification for Steel Structural Tubing


JDM A26
f
TABLE 1. DESIGNATIONS&

-:
JDM DESCRIPTION
Number

A26A Standard Weight (STD) Steel Pipe, Plain End, Biac~ ASTM A53 Type F, or Grade A (Type E or S)

A26A1 Standard Weight (STD) Steel Pipe, Plain End, Galvanized; ASTM A53 Type F, or Grade A (Type E
or S)

A26A2 Standard Weight (STD) Steel Pipe, Plain End, Black; ASTM A53 Grade B (Type E or S)

A26A3 Standard Weight (STD) Steel Pipe, Plain End, Bare; ASTM A714 Class 2 (Type F, E or S; Grade 1,
11,or Ill)A

A26B Extra Strong (XS) Steel Pipe, Plain End, Black; ASTM A53 Type F, or Grade A (Type E or S)

A26B1 Extra Strong (XS) Steel Pipe, Plain End, Black ASTM A53 Grade B (Type E or S)

A26B2 Extra Strong (XS) Steel Pipe, Plain End, Bare; ASTM A714 Class 2 (Type F, E or S; Grade 1, 11,or
III)A

A26C Double Extra Strong (XXS) Steel Pipe, Plain End, Black; ASTM A53 Type F, or Grade A
(Type E or S)

A26D (Discontinued. Replaced by JDM A22G Hot-Formed Steel Structural Tubing.) i

A26E Light Wall (LW) Schedule 10 Steel Pipe, Plain End, Black; ASTM Al 35 Grade A I

AFor nominal pipe sizes NPS 4 and larger, ASTM Al 39 Grade E may be substituted.
I

You might also like