Scribd
Upload
227 views3 pages

Bosch Sensor TPS

This document provides information about an angle sensor used to measure the angle of rotation of a throttle valve in motor vehicles. The sensor is a potentiometric angular-position sensor with a linear characteristic curve that converts the throttle valve angle into a proportional voltage ratio. It is designed to withstand extreme operating conditions in the engine compartment. The sensor has a useful measurement range of up to 88 degrees and outputs a voltage corresponding to the measured angle.

Uploaded by

Sport Rally Team
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
227 views3 pages

Bosch Sensor TPS

This document provides information about an angle sensor used to measure the angle of rotation of a throttle valve in motor vehicles. The sensor is a potentiometric angular-position sensor with a linear characteristic curve that converts the throttle valve angle into a proportional voltage ratio. It is designed to withstand extreme operating conditions in the engine compartment. The sensor has a useful measurement range of up to 88 degrees and outputs a voltage corresponding to the measured angle.

Uploaded by

Sport Rally Team
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

0 280 122 001 1/3

Angle sensor
Measurement of angles up to 88°
Input quantity: Ø
Output quantity: R

• Potentiometric angular-position
sensors with linear characteristic
curve.
• Sturdy design for exacting
demands.
• Compact size.

Application
Sensors of this type are used in motor
vehicles to record the angle of rotation of
the throttle valve. They are exposed to
extreme operating conditions, being
attached directly to the throttle valve
housing by means of an extended throttle
valve shaft in the engine compartment. To
maintain reliable operation under such
conditions, the sensors are resistant to
fuels, oils, saline fog and industrial
atmospheres.

Design and operation


The throttle-valve angular-position sensor
is a potentiometric angular-position
sensor with a linear characteristic curve.
It is used with fuel-injection engines to
convert the angle of rotation of the
throttle valve into a proportional voltage
ratio. To do so, the rotor with its special
wipers connected to the throttle-valve
shaft travels along corresponding
resistance tracks, with the position of the
throttle valve being converted into the
above-mentioned voltage ratio. The
throttle-valve angular-position sensors
have no return spring. The throttle-valve
angular-position sensor 0 280 122 001
has one linear characteristic curve. The
throttle-valve angular-position sensor 0
280 122 201 has two linear characteristic
curves. This permits a particularly high
resolution in the angle range 0°
23°.

Explanation of characteristic
quantities
U Output voltage uSupply voltage
ØAngle of rotation ÈOutput-
voltage characteristic curve 2 É
Output-voltage characteristic
curve 3

Robert Bosch GmbH


Automotive Aftermarket
Postfach 410960
76225 Karlsruhe
Germany

www.bosch-sensoren.de
0 280 122 001 2/3

Part number 0 280 122 001


Technical data
Useful electrical angle range degrees e 86
Useful mechanical angle range degrees e 86
Angle between internal stops (must not be reached when fitted) degrees i 95
Direction of rotation Any
Total resistance (term. 1-2) kO 2 + 20 %
Wiper protective resistor (wiper in zero position, term. 2-3) O 710 ... 1380
Operating voltage u V 5
Load Ohmic resistance
Permissible wiper current zA e 18
Voltage ratio from stop to stop - characteristic curve 1 0,04 e U/u e 0,96
Slope of nominal characteristic curve deg! 0,00927
Operating temperature - 40 °C ...+ 130 °C
Approximate value for permissible vibration acceleration m/s2 e 700
Service life (rotary cycles) Mill. 2
Accessories are not included in the scope of delivery of the sensor and are therefore to be ordered separately as required.

Dimensional drawing Characteristic curve

A Internal stop
L Positional tolerance of wiper when
attached NNominal characteristic
curve
T Tolerance limits
C Useful electrical angle range

A Plug connection
B O-ring 14.65 x 2 mm
C Attachment dimensions for throttle-valve housing
D Clockwise
E Anti-clockwise
Ö Throttle-valve opening direction
0 280 122 001 3/3

Circuit diagram 1 Circuit diagram 2

Accessories Part number


Connector 1 237 000 039
Accessories are not included in the scope of delivery of the sensor and are therefore to be ordered separately as required.

You might also like