Downloaded From : www.EasyEngineering.

net

ww
w.E
a syE
ngi
nee
rin
g.n
et

**Note: Other Websites/Blogs Owners Please do not Copy (or) Republish

this Materials, Students & Graduates if You Find the Same Materials with
EasyEngineering.net Watermarks or Logo, Kindly report us to
[email protected]

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

LT P C
IC8451 CONTROL SYSTEMS
3204
OBJECTIVES:
➢ To understand the use of transfer function models for analysis physical systems and
introduce the control system components.
➢ To provide adequate knowledge in the time response of systems and steady state error
analysis.
➢ To accord basic knowledge in obtaining the open loop and closed–loop frequency
responses of systems.
➢ To introduce stability analysis and design of compensators.

ww➢ To introduce state variable representation of physical systems and study the effect of state
feedback.

w.E
UNIT I SYSTEMS AND THEIR REPRESENTATION
Basic elements in control systems – Open and closed loop systems – Electrical analogy of
mechanical and thermal systems – Transfer function – Synchros – AC and DC servomotors –
(9)

UNIT II TIME RESPONSE asy

Block diagram reduction techniques – Signal flow graphs.
(9)

En
Time response – Time domain specifications – Types of test input – I and II order system response
– Error coefficients – Generalized error series – Steady state error – Root locus construction-

UNIT III FREQUENCY RESPONSE

gin
Effects of P, PI, PID modes of feedback control –Time response analysis.
(9)
Frequency response – Bode plot – Polar plot – Determination of closed loop response from open

UNIT IV STABILITY AND COMPENSATOR DESIGN

Characteristics equation – Routh
ee
loop response - Correlation between frequency domain and time domain specifications.

Hurwitz criterion –
rin
Nyquist
(9)
stability criterion-

g.n
Performance criteria - Effect of Lag, lead and lag-lead compensation on frequency response–
Design of Lag, lead, Lag/Lead compensator design using bode plots.

et
UNIT V STATE VARIABLE ANALYSIS (9)
Concept of state variables – State models for linear and time invariant Systems – Solution of state
and output equation in controllable canonical form – Concepts of controllability and observability.
TOTAL (L:45+T:30): 75 PERIODS
COURSE OUTCOMES
At the end of the course, the student should have the:
➢ Ability to develop various representations of system based on the knowledge of
➢ Mathematics, Science and Engineering fundamentals.
➢ Ability to do time domain and frequency domain analysis of various models of linear
➢ system.
➢ Ability to interpret characteristics of the system to develop mathematical model.
➢ Ability to design appropriate compensator for the given specifications.
➢ Ability to come out with solution for complex control problem.
➢ Ability to understand use of PID controller in closed loop system.

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.1

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

TEXT BOOKS
1. Nagrath, I.J. and Gopal, M., “Control Systems Engineering”, New Age International
Publishers, 2017.
2. Benjamin C. Kuo, “Automatic Control Systems”, Wiley, 2014.

REFERENCES
1. Katsuhiko Ogata, “Modern Control Engineering”, Pearson, 2015.
2. Richard C.Dorf and Bishop, R.H., “Modern Control Systems”, Pearson Education,2009.
3. John J.D., Azzo Constantine, H. and Hoopis Stuart, N Sheldon, “Linear Control System
Analysis and Design with MATLAB”, CRC Taylor& Francis Reprint 2009.
4. Rames C.Panda and T. Thyagarajan, “An Introduction to Process Modelling
Identification and Control of Engineers”, Narosa Publishing House, 2017.

ww
5. M.Gopal, “Control System: Principle and design”, McGraw Hill Education, 2012.
6. NPTEL Video Lecture Notes on “Control Engineering “by Prof. S. D. Agashe, IIT
Bombay.

w.E
asy
En
gin
ee rin
g.n
et

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.2

Downloaded From : www.EasyEngineering.net

 Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

SUBJECT CODE: IC 8451 YEAR /SEMESTER: II/04

SUB NAME: CONTROL SYSTEMS SUB HANDLER: ANGELIN J

UNIT I SYSTEMS AND THEIR REPRESENTATION

Basic elements in control systems – Open and closed loop systems – Electrical analogy of mechanical and
thermal systems – Transfer function – Synchros – AC and DC servomotors – Block diagram reduction
techniques – Signal flow graphs.
PART * A

Q.No.

ww Questions

What is control systems. (May/June 2013) (BTL1)

1.
w.E
A system when the output quantity is controlled by varying the input quantity, then the system is
called control system. The output quantity is called controlled variable or response and input
quantity is called command signal or excitation.

2. asy
Define transfer function. (Nov/Dec 2010,13) (BTL1)
The transfer function of a system is defined as the ratio of Laplace transform of output to Laplace

En
transform of input with zero initial conditions.

gin
What is feedback? What type of feedback is employed in control system? (Nov/Dec 2013)
(BTL2)
3.
ee
the feedback is a control action in which the output is sampled, and a proportional signal is given

rin
to input for automatic correction of any changes in desired output. Negative feedback is employed
in control system.

g.n
What are the characteristics of negative feedback? (May/June 2014) (BTL3)
The characteristics of negative feedback are as follows
4.
a. Accuracy in tracking steady state value.
b. Rejection of disturbance signals.
c. Low sensitivity to parameter variations.
d. Reduction in gain at the expense of better stability.
et
Differentiate open loop and closed loop system. (Nov/Dec 2010,14, April/May 2010) (BTL4)

5. S.NO Open loop Closed loop

1. Inaccurate and unreliable Accurate and reliable

2. Simple and economical Complex and costly

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.3

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

3. Changes in output due to Changes in output due to

external disturbances are external disturbances are
not corrected automatically corrected automatically
4. They are generally stable Great efforts are needed to
design a stable system
What is effect of positive feedback on stability? (May/June 2015) (BTL2)
6. The positive feedback increases the error signal and drives the output to instability. The positive
feedback is used in minor loops in control systems to amplify certain internal signals or parameters.
List the advantages of closed loop system. (Nov/Dec 2015, May/June 2012) (BTL1)
7. a. Closed loop systems are accurate and reliable.

ww b. Changes in output due to external disturbances are corrected automatically.

What is Block diagram? What are its basic components? (May 17, Nov/Dec 2015, Nov 11)

8. w.E
(BTL2)
A block diagram of a system is a pictorial representation of the functions performed by each
components of the system and shows the flow of signals. The basic elements of the block diagram

asy
are blocks, branch points and summing points.

En
Define open loops and closed loop control system. (April/May2011, Nov/Dec 11) (BTL1)
The control systems in which the output quantity has no effect upon the input quantity are called

gin
9. open loop control system. This means that the output is not feedback to the input for correction.
The control systems in which the output quantity has an effect upon the input quantity in order to
maintain the desired output value are called closed loop control system.

10. a.
b.
Simple and economical
Stable system
ee
What are the advantages of open loop control system? (Nov/Dec 2012) (BTL1)

rin
What are the properties of signal flow graph? (May/June 2012) (BTL1) g.n
The basic properties of signal flow graph are
a. Signal flow graph is applicable to linear systems.
et
b. It consists of nodes and branches. A node is a point representing a variable or signal.
A branch indicates functional dependence of one signal to other.
11.
c. A node adds the signals of all incoming branches and transmits this sum to all other
branches.
d. Signals travel along branches only in the marked direction and when it travels it gets
multiplied by the gain or transmittance of the branch.
e. The algebraic equations must be in the form of cause and effect relationship.

Why negative feedback is preferred in control system? (May 17, Nov/Dec 2016) (BTL2)
12. The negative feedback results in better stability in steady state and rejects any disturbance signals.
It also has low sensitivity to parameter variations. Hence negative feedback is preferred in closed
loop control system.

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.4

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

What are the differences between synchro transmitter and synchro control transformer?
(Nov/Dec 2016) (BTL4)
a. Rotor of synchro transmitter is of dumb bell shape and the rotor of control transformer is
13. cylindrical.
b. The rotor winding of synchro transmitter is excited by an AC voltage. In control
transformer, the induced emf in the rotor is used as an output signal (error signal).

Give practical example of open loop systems. (Dec 11) (BTL2)

14. The practical examples of open loop control systems are, sprinkler used to water a lawn, automatic
toaster, traffic light controller, automatic door opening and closing system.

Give practical example of closed loop systems. (Dec 11) (BTL2)

15.

ww
The practical examples of closed loop control systems are, human being, home heating system,
speed control systems, ship stabilization system, missile launching system, voltage stabilizer,
temperature control systems.

w.E
Name three functional components used in control system. (May 03, Dec 14) (BTL2)
The three functional components used in control systems are:
16. a. Error detectors
b. Controller
c. Feedback
asy
En
State Mason’s Gain formula. (APRIL/MAY 15 and Repeated question, will be there in all
AU question papers) (BTL1)
gin
ee rin
17.
g.n
et
Write the analogous electrical elements in force voltage analogy for the elements of
mechanical translational system. ( BTL3)
a. Force-voltage e.
18. b. Velocity v-current i.
c. Displacement x-charge q.
d. Frictional coefficient B-Resistance R.
e. Mass M- Inductance L.
JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.5

Downloaded From : www.EasyEngineering.net

 Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

f. f. Stiffness K-Inverse of capacitance 1/C.

Write the analogous electrical elements in force current analogy for the elements of
mechanical translational system. ( BTL3)
a. Force-current I.
19. b. Velocity v-voltage v.
c. Displacement x-flux φ.
d. Frictional coefficient B-conductance 1/R.
e. Mass M- capacitance C.
f. f. Stiffness K-Inverse of inductance 1/L.
Write the force balance equation of an ideal mass, dashpot, spring element. (BTL2)
20. a. F = M d2x/dt2 for mass element.
b. F = B dx/dt for dash pot element.

a.
ww c. F = kx for spring element.
What are the disadvantages of block diagram representation? (Nov 18) (BTL2)
b. 21.
c. w.E
a. It is a tedious method of calculating transfer function.
b. overall gain of the system cannot be computed.

asy
PART * B

Write the differential equations governing the mechanical translational system shown in the

En
figure. Draw the electrical equivalent analogy circuits. BTL3 (13M)

gin
ee rin
Answer: Page 1.29-Nagoor kani
➢ Draw the free body diagram (2M) g.n
1.
et
1. Mechanical translational system can be obtained using three basic elements Mass
(M), Spring (K), Damper (B).
2. F = M d2x/dt2 for mass element.
3. F = B dx/dt for dash pot element.
4. F = kx for spring element.
➢ Write the differential equations (2M)
𝑑2 𝑥1 𝑑𝑥1 𝑑
𝑀1 + 𝐵1 + 𝐵 𝑑𝑡 (𝑥1 − 𝑥 ) + 𝐾1𝑥1 + 𝑘 (𝑥1 − 𝑥 ) = 0
𝑑𝑡 2 𝑑𝑡

𝑑2 𝑥 𝑑𝑥 𝑑
𝑀2 𝑑𝑡 2 + 𝐵2 𝑑𝑡 + 𝐵 𝑑𝑡 (𝑥 − 𝑥1) + 𝑘 (𝑥 − 𝑥1) = 𝑓(𝑡)

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.6

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

➢ Write the rule for force voltage and force current analogy (3M)
1. Force voltage: M→L ; K→1/C ; B→R; velocity→I
2. Force current: M→C; K→1/L; B→1/R
➢ Draw the electrical circuit equivalent to mechanical system (3M)
➢ Write the electrical equations using KVL and KCL.(3M)

Derive the transfer function of AC servo motor in control system. BTL4 (13M)
Answer: Page 55-Notes

ww ➢ Definition of Servomotor :- (2M)

1. Motor used for feedback control systems are called servomotors. It is also called

w.E automatic control system.

2. Converts electrical system into angular motion.

asy
3. 2 types: DC servomotor and AC servomotor.

En
➢ Definition of AC Servomotor :- (3M)

2.
gin
1. Motor which runs at zero speed as its base speed is driven by error signal with AC
supply is called servomotor.

applications. ee
2. Used in closed loop servo systems, high speed instrument servos, and low power

rin
3. Speed control done using armature voltage control and field control.
➢ Operating principle of AC Servomotor (4M) g.n
et
Salient features include rugged construction, Reliable in operation, Light Weight and No
Slip rings.
➢ Transfer function derivation (4M)
Ө(s)/Vc2(s)=Km/s(1+stm)

Compare open and closed loop systems. BTL4 (13M)

Answer: Page 1.29-Nagoor kani
3. ➢ Definition of open and closed loop systems (3M)
Open loop: any physical system that does not automatically correct the variation in its
output is called open loop system.

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.7

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

Closed loop: A system in which control action is somehow dependent on the output. The
output is given to feedback element and compared with the reference signal.
➢ Block diagram of open and closed loop systems (4M)

ww
w.E
asy
➢ Advantages of open and closed loop systems (2M)
Open loop:
En
1. Simple and economical.
2. Easier to construct. gin
3. Less Stable.
Closed loop:
ee rin
1. Accurate.
g.n
2. More stable.
3. Less noise affected.
et
➢ Disadvantages of open and closed loop systems (2M)
open loop
1. Inaccurate.
2. Unreliable.
3. Cannot correct automatically.

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.8

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

Closed loop:
1. Complex and costly.
2. Oscillatory response.
3. Overall gain reduced.
➢ Applications of open and closed loop systems (2M)
Open loop:
1. Electric switch.

ww 2. Automatic washing machine.

3. Electric toaster.

w.EClosed loop:

asy
1. Traffic light control.
2. Liquid level control.

En
3. Temperature level control.

gin
Write the differential equations governing the mechanical rotational system as shown in the
figure. Draw the both electrical analogous circuits.399(Apr/May 2017) BTL3 (13M)

ee rin
g.n
4. Answer: Page1.46-Nagoor kani
et
➢ Draw the free body diagram (4M)
1. Mechanical Rotational system can be obtained using three basic elements Moment of
Inertia (J), Spring (K), Damper (B).
2. F = M d2θ/dt2 for mass element.
3. F = B d θ /dt for dash pot element.
4. F = k θ for spring element.

➢ write differential equations (2M)

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.9

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

𝑑2 𝜃1 𝑑(𝜃1−𝜃2)
𝐽1 + 𝐵1 + 𝐾1(𝜃1 − 𝜃2) = 𝑇
𝑑𝑡 2 𝑑𝑡

𝑑2 𝜃2 𝑑(𝜃2−𝜃1) 𝑑(𝜃2−𝜃3)
𝐽2 + 𝐵1 + 𝐾1(𝜃2 − 𝜃1) + 𝐵2 =0
𝑑𝑡 2 𝑑𝑡 𝑑𝑡

𝑑2 𝜃3 𝑑(𝜃3−𝜃2)
𝐽3 + 𝐵2 + 𝐾2(𝜃3 − 𝜃2) = 0
𝑑𝑡 2 𝑑𝑡

➢ Write the rule for torque voltage and torque current analogy (3M)

ww Torque-voltage rule:
1. Angular Velocity v-current i.
2. Angular Displacement x-charge q.

w.E3. Frictional coefficient F-Resistance R.

4. Mass J- Inductance L.
5. Stiffness K-Inverse of capacitance 1/C.
Torque -current rule:
asy
1. Angular Velocity v-voltage v.
2. Angular Displacement x-flux φ.

En
3. Frictional coefficient F conductance 1/R.
4. Mass J- capacitance C.

gin
5. Stiffness K-Inverse of inductance 1/L.
➢ Draw the electrical circuit equivalent to mechanical system (4M)

and DC servo motors.(Nov/Dec 2014) BTL4

ee
Differentiate DC and AC servo motors (or) With neat diagrams, explain the working of AC
(13M)
rin
Answer: notes.
➢ Definition of Servomotor (3M)
g.n
5.
automatic control system.
et
1. Motors are used for feedback control systems are called servomotors.it is also called

2. Converts electrical system into angular motion.

3. 2 types: DC servomotor and AC servomotor.
➢ Definition of AC Servomotor & DC Servomotor, Block diagram of AC & DC
Servomotor (4M)
1. Motors which runs at zero speed as its base speed is driven by error signal with AC supply
is called servomotor.

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.10

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

2. Used in closed loop servo systems, high speed instrument servos, and low power
applications.
3. Speed control done using armature voltage control and field control.
➢ Operating principle of AC & DC Servomotor (4M)
Salient features include rugged construction, Reliable in operation, Light Weight and No
Slip rings.
➢ Applications of AC & DC Servomotor (2M)
DC:

ww 1. Large power applications.

w.E
2. Robotics.
AC

asy
1. Solar Tracking System.

En
2. Antenna Positioning.
3. Robotic Vehicle.

gin
Convert the given block diagram shown in fig. to signal flow graph and determine the closed

(13M)
ee
loop transfer function C(s)/R(s). And verify by block diagram reduction approach.

rin
BTL4

g.n
6.
et
Answer: Page 1.56-Nagoor Kani
➢ Draw the signal flow graph.
➢ Give the numbering to input, output, summing point and branching point (2M)
➢ Apply block diagram reduction rules to find transfer function (6M)

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.11

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

1. Reduce series blocks.

2. Reduce parallel blocks
3. Reduce minor feedback loops.
4. Shift summing point to left and take-off point to right.
5. Splitting the summing points.
➢ Apply Masons gain formula (2M)

ww
w.E
asy
En
gin
ee rin
➢ Find transfer function (3m)
C(s)/R(s)= G1G2G3G4/(1+G3G4H1+G2G3H2+G1G2G3G4) g.n
et
Derive the transfer function of an armature controlled DC servomotor (or) Obtain the
mathematical model of an armature controlled DC motor. (Nov/Dec 2016) BTL3 (13M)
Answer: Page 1.21-Nagoor kani

7. ➢ Explain speed control techniques (2M)

a)Armature control
b)Field control
➢ Draw the equivalent circuit diagram (2M)

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.12

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

ww
w.E➢ Derive the differential equation (4M)
𝑑𝑖𝑎

asy
𝑉𝑎 = 𝑖𝑎 𝑅𝑎 + 𝐿𝑎

𝑑2 𝜃 𝑑𝜃
𝑑𝑡
+ 𝑒𝑏

En
𝑇 = 𝐽 𝑑𝑡 2 + 𝐵 𝑑𝑡

➢ Take Laplace transform (2M)

gin
𝑖𝑎 (𝑠)𝑅𝑎 + 𝐿𝑎 𝑠𝑖𝑎 (𝑠) + 𝐸𝑏 (𝑠) = 𝑉𝑎 (𝑠)

𝐽𝑠 2 𝜃(𝑠) + 𝐵𝑠𝜃 (𝑠) = 𝑇(𝑠)

➢ Find transfer function (3M)
ee rin
 (s ) Km
s  ( R a + L a s ) ( J s + b) + K b K m
g.n
8.
V a( s )
et
Obtain the transfer function using Mason’s Gain formula for the system given. (Apr/May
2017). BTL3 (13M)

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.13

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

wwAnswer: Page1.79-Nagoor kani

➢ Give the numbering to all nodes(2M)

w.E ➢ Find No.of forward paths and individual loop gain(3M)

No of forward path ,K=6
Forward path gain: asy
1. P1=G2G4G6
En
2. P2=G3G5G7
gin
3. P3=G1G2G7
4. P4=G3G8G6
5. P5=-G1G3G7G8H1
ee rin
6. P6=-G1G2G6G8H2 g.n
➢ Calculate the value of delta(3M)
Δ=1+G4H1+G5H2+-G1G2H1H2+G4G4H1H2
et
➢ Apply Masons gain formula(2M)

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.14

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

ww ➢ Find transfer function(3M)

w.E
C(s)/R(s)= -G1G3G7G8H1-G1G2G6G8H2/(1+G4H1+G5H2-G1H8H1H2+G4G5H1H2)

(Nov/Dec 2016).
asy
Write the differential equation for the electric circuit as shown in fig. hence Find Y 2(s)/F(s).
BTL2 (13M)

En
Answer: Page1.10-Nagoor Kani

gin
➢ Draw the free body diagram of mass M1 &M2 (3M)

ee
➢ Write differential equations in terms of displacement (4M)

rin
g.n
9.
et
𝑑2 𝑦1 𝑑𝑦1
𝑀1 + 𝐵1 + 𝑘1𝑦1 + 𝑘2(𝑦1 − 𝑦2) = 𝑓(𝑡)
𝑑𝑡 2 𝑑𝑡

𝑑2 𝑦2
𝑀2 + 𝐾2(𝑦2 − 𝑦1) = 0
𝑑𝑡 2

➢ Take Laplace transform (3M)

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.15

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

1. M1s2y1(S)+Bsy1(s)+K1y1(s)+K2(y1(s)-y2(s))-F(s)
2. M2 s2Y2(s)+K2(y2(s)-y1(s))=0
➢ Rearrange the equation and find transfer function (3M)
➢ Y2(s)/F(s)=K2/[M1s2+Bs+(K1+K2)] [M2s2+K2]-k22

Obtain the electrical analogy of the mechanical systems shown in the following Fig(Nov 18)

ww
w.E
asy
Answer: Page1.101-Nagoor Kani

En
➢ Draw the free body diagram (2M)
1. Mechanical translational system can be obtained using three basic elements Mass

gin
(M), Spring (K), Damper (B).
2. F = M d2x/dt2 for mass element.
10.
4. F = kx for spring element. ee
3. F = B dx/dt for dash pot element.

➢ Write the differential equations (2M)

rin
𝑀1
𝑑2 𝑥1
𝑑𝑡 2
+ 𝐵1
𝑑𝑥1
𝑑𝑡
𝑑 𝑑

g.n
+ 𝐵2 𝑑𝑡 (𝑥1 − 𝑥2) + 𝐵3 𝑑𝑡 (𝑥1 − 𝑥3) + 𝐾1𝑥1 = 𝑓 (𝑡)

𝑀2
𝑑 2 𝑥2
𝑑𝑡 2
+ 𝐵2
𝑑 (𝑥2 − 𝑥1)
𝑑𝑡
𝑑
+ 𝐵 (𝑥2 − 𝑥3) = 0
𝑑𝑡
et
𝑑 2 𝑥3 𝑑 (𝑥3 − 𝑥1) 𝑑
𝑀3 2
+ 𝐵3 + 𝐵 (𝑥3 − 𝑥2) = 0
𝑑𝑡 𝑑𝑡 𝑑𝑡
➢ Write the rule for force voltage and force current analogy (3M)
1.Force voltage: M→L ; K→1/C ; B→R; velocity→I
2.Force current: M→C; K→1/L; B→1/R
➢ Draw the electrical circuit equivalent to mechanical system (3M)

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.16

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

➢ Write the electrical equations using KVL and KCL(3M)

PART * C

What are the basic elements of mechanical rotational and translational systems? Write its
torque balance and force balance equations. (May/June 2016). BTL3 (15M)
Answer: Page 1.15-Nagoor Kani
➢ Elements of mechanical system(2M)
1. Mass(M), Dashpot(B), Spring(K)

ww 2. Moment of inertia (J), Dashpot(F), Spring(K)

w.E➢ Draw the free body diagram(2M)

➢ Apply Newton’s second law(1M)

asy
The second law states that the acceleration of an object is dependent upon two variables -
the net force acting upon the object and the mass of the object.

En
➢ Write differential equations(2M)

gin
1. F(t)= M d2θ/dt2 + B dθ/dt+kθ
2. T(t)= M d2θ/dt2 + B dθ/dt+ kθ
1.
ee
➢ Force balance equation of translational system(4M)
1. F = M d2x/dt2 for mass element. rin
2. F = B dx/dt for dash pot element.
3. F = kx for spring element. g.n
➢ Force balance equation of rotational system(4M)
et
1. Mechanical Rotational system can be obtained using three basic elements Moment of
Inertia (J), Spring (K), Damper (B).
2. F = M d2θ/dt2 for mass element.
3. F = B d θ /dt for dash pot element.
4. F = k θ for spring element.
Torque-voltage rule:
1. Angular Velocity v-current i.
2. Angular Displacement x-charge q.
3. Frictional coefficient F-Resistance R.
4. Mass J- Inductance L.
5. Stiffness K-Inverse of capacitance 1/C.
Torque -current rule:
1. Angular Velocity v-voltage v.
JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.17

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

2. Angular Displacement x-flux φ.

3. Frictional coefficient F conductance 1/R.
4. Mass J- capacitance C.
For a non-unity negative feedback control system whose open loop transfer function is G(s)
and feedback path transfer function is H(s), obtain the control ratio using Mason’s gain
formula. (Nov/Dec 2015). BTL6 (15M)
Answer: Page 1.75-Nagoor Kani
➢ Draw the closed loop system(2M)

ww
w.E
asy
En
2.
G(s) = any value. gin
➢ Choose G(s) and H(s) value(2M)

H(s)=1
➢ Apply Masons gain formula(5M)
ee rin
g.n
et

➢ Find the transfer function(6M)

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.18

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

➢ G(s) = output/input.

Derive the transfer function of an RLC series circuit. (Nov/Dec 2015). BTL5 (15M)

ww
3. w.E
Answer: Page 1.20-Nagoor kani

asy
➢ Draw the RLC Circuit(2M)

En
➢ Write KVL equations to input and output side (3M)

gin
1. Ri+ Ldi/dt + 1/Cʃi.dt = Vi
2. 1/Cʃi.dt=Vo

ee
➢ Take Laplace transform of differential equations(4M)
Ri(s)+L s i(s) + 1/Cs i(s)= v(s) rin
➢ Rearrange the Laplace equations and find transfer function(6M)
g.n
G(s)=Vo/Vi

(Nov/Dec 2015) BTL5 (15M)

et
With a neat diagram, derive the transfer function of a field-controlled control system.

Answer: Page 1.24-Nagoor Kani

4.
➢ Explain speed control techniques(2M)
a) Armature control b) Field control
➢ Draw the equivalent circuit diagram(2M)

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.19

Downloaded From : www.EasyEngineering.net

 Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

ww ➢ Derive the differential equation (3M)

𝑑𝑖𝑓 𝑑2𝜃 𝑑𝜃

w.E 𝑉𝑓 = 𝑖𝑓 𝑅𝑓 + 𝐿𝑓

➢ Take Laplace transform (3M)

𝑑𝑡
+ 𝑒𝑏 𝑇=𝐽
𝑑𝑡 2
+𝐵
𝑑𝑡

asy
𝑖𝑓 (𝑠)𝑅𝑓 + 𝐿𝑓 𝑠𝑖𝑓 (𝑠) + 𝐸𝑏 (𝑠) = 𝑉𝑓 (𝑠)

En
𝐽𝑠 2 𝜃(𝑠) + 𝐵𝑠𝜃(𝑠) = 𝑇(𝑠)
➢ Find transfer function(5M)
gin
 (s )
V f(s )
Km
ee
s  ( J s + b) ( L f  s + R f )
rin
UNIT II TIME RESPONSE
g.n
Time response – Time domain specifications – Types of test input – I and II order system response – Error

PID modes of feedback control –Time response analysis.

PART * A
et
coefficients – Generalized error series – Steady state error – Root locus construction- Effects of P, PI,

Q.No. Questions

State the various standard test inputs used in control system. (Dec 05, May 11, 14) (BTL1)
1. The various standard test inputs used in control system are step ramp, parabolic, impulse and
sinusoidal.

Define peak overshoot. (April/May 17) (BTL1)

2. It is defined as the ratio of the maximum peak value to final value, where maximum peak value is
measured from final value.
3. What is steady state error? (May 04,06,07,11, Dec 11, 15) (BTL1)

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.20

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

The difference between the desired output i.e. reference input and the actual output of the system
is called steady state error which is denoted as e ss.

What is rise time? (Dec 04,08, Nov 11, May 14) (BTL1)
It is the time required for the response to rise from 10% to 90% of the final value for over damped
4.
systems and 0 to 100% of the final value for under damped systems. The rise time is reciprocal of
the slope of the response at the instant, the response is equal to 50% of the final value.

What is settling time? (May 03, 05, 10, Dec 14) (BTL1)
5. The settling time is defined as the time required for the response to decrease and stay within
specified percentage of its final value (within tolerance band)
List out any four time-domain specification. (Dec 03,08, 15) (BTL1)
6.
ww
The various time domain specifications are delay time, rise time, peak time, peak overshoot, settling
time and steady state error.

w.E
Mention the characteristics of PI controller. (Dec 03, May 07, 13, 14) (BTL2)
The PI controller has following characteristics

7. asy
➢ It increases order of the system.
➢ It increases TYPE of the system.

En
➢ Design of Ki must be proper to maintain stability of system. So, it makes system r relatively
less stable.

gin
➢ Steady state error reduces tremendously for same type of inputs.

8. response. ee
Define transient response and steady state response of a system. (May 10) (BTL1)
The output variation during the time it takes to achieve its final steady value is called transient

rin
Steady state response is that part of the time response which remains after complete transient
response vanishes from the system output.
g.n
et
How a control system is classified depending on the value of damping? (May 11) (BTL2)
➢ Under damped system (0< ᵷ < 1 )
9. ➢ Critically damped system (ᵷ = 1)
➢ Over damped system (ᵷ > 1)
➢ Un-damped system (ᵷ = 0)

Why derivative controller is not used in the control system? (May 11, May 15) (BTL2)
The derivative controller acts only during transient period when the error varies with time and does
10 not produce any corrective action for a constant error as derivative of a constant error is zero.
Hence the derivative controller is never used alone but always used along with some other type of
controller.

What is the effect of adding a pole to a second order system? (May 04, 08) (BTL2)
11 The second order system is generally stable. If a pole is added to it, it becomes third order due to
which it becomes less stable in nature. It increases peak overshoot and settling time.

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.21

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

State the advantages of generalized error coefficients. (May 06) (BTL1)

➢ It gives variation of error as a function of time.
12 ➢ It uses any input other than the standard input.
➢ As variation of error as a function of time is available, the design of the system becomes
easy and optimum.
Define adaptive control system. (Dec 06) (BTL4)
Adaptive control system has a property or an automatic control system having a property of
automatically changing the characteristics, system parameters and / or structure of the controller
13 during the normal operation with the aim of maintaining a given standard of performance under
varying inputs and varying arbitrary, conditions of operation is called as adaptive or self-adjusting
system.

14 ww
What is the function of controller? (BTL2)
A controller accepts error as its input and manipulates the error according to the requirement of the

w.E
system and gives output to the plant or the process to be controlled.
What is type 0 and type 1 system? (May 2015) (BTL2)

of the system
asy
The value of N in the denominator polynomial of loop transfer function decides the type number

➢ N- Number of poles at origin.

15
En
➢ N = 0, then the system is type 0 system,
➢ N = 1, the system is type 1 system.

gin
➢ N = 2, then the system is type 2 system and so on.

ee rin
What is the effect of PI controller on the system performance? (Dec 14) (BTL2)
16
g.n
The PI controller increases the order of the system by one, which results in reducing, the steady
state error. But the system becomes less stable than the original system.

17
Define peak time. (Dec 09) (BTL1)
et
The time at which the peak overshoot occurs in the time response of a second order system is called
a peak time.
What will happen to damping factor and natural frequency of oscillations if gain K of a
18 second order system is increased? (May 07) (BTL3)
As the value of gain K increases the natural frequency of oscillations and the value of damping
ratio decreases. Due to this system becomes more oscillatory in nature.
How can the maximum overshoot of a system be decreased without affecting the steady state
19 error? (BTL3)
With the use of PD i.e. proportional plus derivative controller, it can be observed that transient
response and value of damping ratio increases without affecting steady state error. As damping

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.22

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

ratio increases, the maximum overshoot decreases. So, using PD controller it is possible to decrease
maximum overshoot without affecting the steady state error.
Why derivative is not used in control systems? (BTL 5)
20 The derivative controller produces a control action based on the rate of change of error signal and
it does not produce corrective measures for any constant error. Hence derivative controller is not
used in control system.
PART * B

Determine the response of the system and find time domain specifications of the given figure.
ζ =0.5 (May/June 2016). BTL3 (13M)

ww
w.E
asy
Answer: Page 2.26-Nagoor kani.
En
➢ Choose G(s) and H(s) (2M)
gin
ee
1. G(s)=16/s(s+0.8)

1. 2. H(s) = Ks+1.
➢ Find transfer function (1M) rin
1. G(s)H(s)= G(s)/1+G(s)H(s) g.n
2. G(s) H(s)= 16/s2+(0.8+k) s+16.
➢ Compare with standard second order expression(2M)
et
1. G(s) =ɷn2/ s2+2ℇɷn s+ ɷn2.
➢ Find ζ and w n (2M)
1. wn 2=16
wn =sqrt (16) = 4
2. 2 ζ wn =(0.8+K) =>K=0.2
Final transfer function:

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.23

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

3. 16/ s2 + 4s+16.
➢ Find response & time domain specifications using formulas(5M)
1. Formula for Rise time: -

Rise time = 0.64s

2. Formula for Peak time: -

ww Peak time = 0.907s

w.E 3. Formula for Settling time: -

asy Settling time = 1.5s

En
4. Formula for Peak overshoot: -

gin
ee Peak overshoot =16.3%

rin
A unity feedback system has 10/s2(s+2). find the steady state error and generalized error
coefficients for r (t) =6t4+5t3+4t2+2t+3. (May/June 2016).
Answer: Page 2.48-Nagoor Kani
BTL3 (13M)
g.n
➢ Choose G(s) and H(s) (1M)
1. G(s)=10/s2(s+2)
et
2. 2. H(s)=1
➢ Find transfer function (2M)
G(s)H(s)= G(s)/1+G(s)H(s)
➢ Apply r(t) in S domain to the system (5M)
1. E(s) = R(s)/ 1+G(s) H(s).
2. R(s) =3/s+ 2/s2 + 4/s3 + 5/s4 + 6/s5.

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.24

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

3. G(s)=10/s2(s+2)
➢ Find ess using final value theorem in S domain (5M)

Derive the time domain specifications of a second order system. (May/June 2016). BTL1
(13M)
Answer: Page 2.17- Nagoor Kani
➢ Rise time definition and its formula (3M)

ww The time required for the response to rise from 0% to 100% of its final value. This is

w.E applicable for the under-damped systems.

asy
➢ Peak time definition and its formula (3M)

En
The time required for the response to reach the peak value for the first time. It is denoted

gin
by tp. At t=tp, the first derivate of the response is zero.

3.
ee rin
➢ Settling time definition and its formula (3M)

g.n
The time required for the response to reach the steady state and stay within the specified

et
tolerance bands around the final value. The settling time is denoted by ts.

➢ Maximum overshoot definition and its formula (4M)

Peak overshoot Mp is defined as the deviation of the response at peak time from the final
value of response. It is also called the maximum overshoot

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.25

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

For a unity feedback control system, the open loop transfer function is given by
G(s) = 10(s+2)/s2(s+1). Find the position, velocity, and acceleration error coefficients and find
the steady state error when the input is R(s) =3/s-2/s2+1/3s3. (May/June 2016). BTL3
(13M)
Answer: Page 2.41-Nagoor kani
➢ Choose G(s) and H(s) & Find transfer function (3M)
➢ Find Kp, Kv, Ka (5M)
1. Kp=α

4.
ww 2. Kv= α

w.E
3. Ka=20
➢ Apply r(t) in S domain to the system (5M)

asy
1. E(s) = R(s)/ 1+G(s) H(s).
2. R(s) =3/s-2/s2+1/3s3
3. G(s)=10(s+2) /s2(s+1) En
gin
➢ Find ess using final value theorem in S domain (5M)

ee rin
ess = 1/60.
g.n
et
With a neat diagram explain the effect of PD controller in detail. (May/June 2016).
Answer: Page 2.62-Nagoor Kani BTL5 (13M)
➢ Transfer function of P & D Controller (3M)
U(s)/E(s) = Kp (1+Td S)
5.
➢ Block diagram of PD Controller (3M)
➢ Compare with standard second order expression (3M)
Loop transfer function= Gc(s)G(s) / 1+ Gc(s)G(s)H(s)
= Kp (1+Td s) * {ɷn2/ s2+2ℇɷn s+ ɷn2.}

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.26

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

= ɷn2 (Kp+ Kd s) / (s2+ (2ℇɷn + Kdɷn2) s +Kp ɷn2)

➢ Justify the results(4M)
1. Addition of zero Increases the peak overshoot and reduces the rise time.
2. Increased damping reduces the peak overshoot.

Write explanatory notes on PI and PD controllers. (May/June 2016) BTL5 (13M)

Answer: Page 2.54 & 2.56-Nagoor Kani
➢ Transfer function of PI & PD Controller (3M)

ww 1. U(s)/E(s) = Kp (1+Td S)
2. U(s)/E(s) = Kp (1+TiS)/TiS

w.E➢ Block diagram of PD Controller (3M)

asy
➢ Compare with standard second order expression (3M)
1. Loop transfer function PD= Gc(s)G(s) / 1+ Gc(s)G(s)H(s)

En = Kp (1+Td s) * {ɷn2/ s2+2ℇɷn s+ ɷn2.}

gin = ɷn2 (Kp+ Kd s) / (s2+ (2ℇɷn + Kdɷn2) s +Kp ɷn2)

6.
ee
2. Loop transfer function PI= Gc(s)G(s) / 1+ Gc(s)G(s)H(s)

rin
= Kp (1+Ti s / Ti s) * {ɷn2/ s2+2ℇɷn s+ ɷn2.}

g.n
= Kiɷn2(10+ Ti s) / (s3+ (2ℇɷns2 + Kpɷn2 s +Kiɷn2)

➢ Justify the results(4M)

PD controller:
et
1. Addition of zero Increases the peak overshoot and reduces the rise time.
2. Increased damping reduces the peak overshoot.
PI controller:
1. Increase in order results in less stability
2. Increase in the type reduces the steady state error.

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.27

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

Derive the expressions for the unit step response of a second order of the underdamped and
undamped systems. (Nov/Dec 2015). BTL1 (13M)
Answer: Page 2.10 & 2.11-Nagoor kani
➢ Draw block diagram of second order system(2M)

7. ww ➢ Find transfer function(2M)

w.E 1. G(s)H(s)= G(s)/1+G(s)H(s)

asy
2. G(s) =ɷn2/ s2+2ℇɷn s+ ɷn2.
➢ Apply the input signal (3M)
R(s)= 1/s En
y (t ) = 1 −
1
(
g in) e
➢ Use partial fraction method find the response of the system(6M)

e − nt sin n 1 −  2 t + 
1−  2

e rin
g.n
The open loop transfer function of a unity feedback system is given by G(s) =1/s (1+s). The
input to the system is described by r (t)= 4+6t.Find the generalized error coefficients and
steady state error. (Nov/Dec 2015). BTL3
Answer: Page 2.48-Nagoor kani
(13M)

➢ Choose G(s) and H(s) & Find transfer function(2M)

et
8.
R(s) =4/s+6/t2
G(s)=1/s(s+1)
H(s)=1
➢ Apply r(t) to find ess using initial value theorem or final value theorem(6M)

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.28

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

➢ Find C0, C1, C2 from static error constants(5M)

1. C0=1/1+kp
2. C1=1/Kv
3. C3=1/ka

(i)Develop an Expression to find steady state error of closed Loop system BTL 4 (6M)
Answer: Page.2.48-Nagoor kani

ww ➢ Choose G(s) and H(s) & Find transfer function (3M)

w.E1. E(s)= R(s)/[1+G(s)H(s)]

2. e(t)= LT-1(E(s))

asy
G(s)=transfer function
H(s)= feedback
En
gin
➢ Apply r(t) to find ess using initial value theorem or final value theorem (3M)
1. Ess= t→∞ LT (e(t))

9.
ee rin
(ii) A unity feedback system has the forward transfer function
g.n
et
For the input r (t) = 1 + 5t, formulate the minimum value of K so that the steady state error
is < 0.1. (Use final value theorem). BTL 4 (7M)

Answer: Page.2.48-Nagoor kani

➢ Choose G(s) and H(s) & Find transfer function(4M)
1. G(s)=Ks/(s+1)2.
2. H(s)=1

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.29

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

3. R(s)=1/s+5/s2
➢ Apply r(t) to find ess using final value theorem (3M)

The open loop transfer function of a unity feedback system is given by G(s)=40/(s(0.2s+1)).
Determine the steady state error using error series approach for the input
r(t)=3t+4t2.).(May/June 2016). BTL3 (13M)
Answer: Page 2.45-Nagoor kani

ww ➢ Choose G(s) and H(s) & Find transfer function(4M)

w.E 1. G(s)=40/s(0.2s+1)
2. R(s)=3/s2+4/s4

10.
3. H(s)=1
asy
➢ Apply r(t) to find ess using initial value theorem or final value theorem(6M)

En
gin
1. C0=1/1+kp
ee
➢ Find C0, C1, C2 from static error constants(5M)

rin
2. C1=1/Kv
g.n
et
3. C3=1/ka

A unity feedback control system has the open loop transfer function G(s)=K/(s+A) (s+2). Find
the values of K and A, so that the damping ratio is 0.707 and the peak time for unit step
response is 1.8s. (Nov/Dec 2015). BTL2 (13M)
Answer: Page.2.26-Nagoor kani
11. ➢ Choose G(s) and H(s) & Find transfer function(2M)
1. G(s)= K/ (s +A) (s+2)
2. ꜫ=0.7
3. TPJ=1.8

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.30

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

➢ Compare with standard expression(2M)

G(s) =ɷn2/ s2+2ℇɷn s+ ɷn2= K/(s+A) (s+2)
➢ Find Wn, also find K, A by using peak time(9M)
1. 2ℇɷn=(A+2)
2. Tp=1.8
π/wn(sqrt(1-ℇ2)) =1.8 (calculate Wn)
3. Substitute the value in eq.1 and find the value of A.

ww
Obtain the impulse and step responses of the following unity feedback control system with
open loop transfer function. G(s) =6/(s(s+5)). (Nov/Dec 2015). BTL2 (13M)

w.E
Answer: Page 2.81--Nagoor kani
➢ Choose G(s) and H(s) & Find transfer function(2M)

asy
1. C(s)/R(s)=G(s)/1+G(s)
2. C(s)=R(s)* 6/s(s+5)
En
13.
3. Step response R(s)=1/s
C(s)= 1/s * 6/s(s+5) gin
4. Impulse response R(s)=1
C(s)= 1 * (6/s(s+5))
ee rin
➢ Apply input signal R(s), Find response of the system(5M)
g.n
et
The time domain response c(t) is obtained by taking inverse Laplace transform of C(s)
➢ Find derivative of response of system is response of impulse system(6M)
The time domain response c(t) is obtained by taking inverse Laplace transform of C(s)

Sketch the root locus of the system.

G(s)=K(s+3)/s(s+1) (s+2) (s+4). (Apr/May 2017). BTL 6 (13M)
Answer: Page 4.75-Nagoor kani
14. ➢ Find poles and zeros (2M)
1.Poles=0, -1, -2, -4 (n=4)
2.Zeros= -3 (m=1)

➢ Centroid and angle of asymptotes (3M)

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.31

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

1.centroid=sum of poles-sum of zeros/ n-m.

2. angle of asymptotes = +/- 1800 (2q+1)/ n-m.

➢ Find breakaway points (4M)

1.G(s)/ 1+G(s)
2. s(s+1) (s+2) (s+4) + K(s+3) =0

➢ Find intersection of real axis with imaginary axis (4M)

1.s(s+1) (s+2) (s+4) + K(s+3) =0
2.s→ jw
3. equate the real and imaginary parts.

ww
Sketch the root locus of the system whose open loop transfer function is G(S) = K / S (S+2)
(S+4). Find the value of K so that the damping ratio of the closed loop system is 0.5.

w.E
Answer: Page 4.72-Nagoor kani
BTL 6 (13M)

asy
➢ Find poles and zeros (2M)
1.Poles=0, -2, -4 (n=3)
2.Zeros= 0 (m=0)
En
➢ Centroid and angle of asymptotes (3M)

15. gin
1.centroid=sum of poles-sum of zeros/ n-m.
2. angle of asymptotes = +/- 1800 (2q+1)/ n-m.

➢ Find breakaway points (4M)

1.G(s)/ 1+G(s)
ee rin
2. s(s+2) (s+4) + K=0

➢ Find intersection of real axis with imaginary axis (4M) g.n

1.s(s+2) (s+4) + K=0
2.s→ jw
3. equate the real and imaginary parts.
et
PART * C

Explain the effect of P, PI and PID controllers on the system performances. (Nov/Dec 2015).
BTL5 (15M)
1.
Answer: Page 2.61-Nagoor kani
➢ Transfer function of P, I & D Controller (5M)

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.32

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

➢ Compare with standard second order expression (2M)

PD controller:
U(s)/E(s) = Kp (1+Td S)
Loop transfer function = Gc(s)G(s) / 1+ Gc(s)G(s)H(s)
= Kp (1+Td s) * {ɷn2/ s2+2ℇɷn s+ ɷn2.}
= ɷn2 (Kp+ Kd s) / (s2+ (2ℇɷn + Kdɷn2) s +Kp ɷn2)
PI controller:

ww U(s)/E(s) = Kp (1+TiS)/TiS
Loop transfer function PI= Gc(s)G(s) / 1+ Gc(s)G(s)H(s)

w.E = Kp (1+Ti s / Ti s) * {ɷn2/ s2+2ℇɷn s+ ɷn2.}

PID controller: asy = Kiɷn2(10+ Ti s) / (s3+ (2ℇɷns2 + Kpɷn2 s +Kiɷn2)

En
U(s)/E(s) = Kp (1+ 1/Tis +Tds)

gin
Loop transfer function PID = Gc(s)G(S)/1+ Gc(s)G(s)H(s)

ee = Kp (1+ 1/Tis +Tds) * {ɷn2/ s2+2ℇɷn s+ ɷn2.}

➢ Block diagram of P, PI, PID Controller (5M)
rin
➢ Justify the results (3M)
PD controller: g.n
et
1. Addition of zero Increases the peak overshoot and reduces the rise time.
2. Increased damping reduces the peak overshoot.

PI controller:
1. Increase in order results in less stability
2. Increase in the type reduces the steady state error
PID controller:
1. Proportional controller stabilizes the gain but introduces the steady state error.

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.33

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

2. The integral controller eliminates the error.

3. The derivative controller reduces the rate of change of error.

A unity feedback system has the forward transfer function G(s) =K1 (2s+1)/s (5s+1) (1+s) 2
The input r(t)=1+6t is applied to the system. Determine the minimum value of K1, if the
steady state error is to be less than 0.1. (Apr/May 2017). BTL3 (15M)
Answer: Page 2.48-Nagoor kani
➢ Choose G(s) and H(s) & Find transfer function(2M)
1. G(s) =K1 (2s+1)/s (5s+1) (1+s)2

ww 2. R(s)=1/s+6/s2
➢ Apply r(t) to find ess using initial value theorem or final value theorem(6M)

2.
w.E1. Ess=0.1.

asy
En
➢ Find C0, C1, and C2 from static error constants (5M).
1. C0=1/1+kp
gin
2. C1=1/Kv
3. C3=1/ka
ee rin
➢ Find value of K(2M)
g.n
et
1. K should be greater than 60

Determine the open loop transfer function for a unit feedback control system with unit
impulse response given by
C (t) = −te −t + 2e−t for (t>0) BTL4 (15M)
Answer: page 71- notes
➢ Laplace transform: (3M)
3.
1. C(s)/R(s)=G(s)/1+G(s)
2. C(s)= -1/(s+1) +2/(s+1)
➢ Response of impulse input: (5M)
R(s)=1

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.34

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

➢ Compare with standard second order expression(4M)

➢ Justify the results (3M)

(i)A certain unity negative feedback control system has the following open loop transfer

ww
function

w.E
Derive an expression for the output variable as a function of time when the input applied is

asy
unit step. What is the percentage overshoot, peak time and rise time? BTL 6 (7M)
Answer: Notes

En
➢ Response of impulse input: (2M)
➢ C(s)/R(s)=G(s)/1+G(s)
gin
➢ C(s)=1* 10(s+10) / s(s+2)

4.
➢ R(s)=1/s
➢ Laplace transform: (2M)
ee rin
g.n
The time domain response c(t) is obtained by taking inverse Laplace Transform of C(s)
c(t)=LT-1 {C(s)}
➢ Compare with standard second order expression (3M)
et
G(s)= {ɷn2/ s2+2ℇɷn s+ ɷn2.}
➢ wn=3.162 rad/sec
➢ ℇ=0.316
➢ Tp= 1.047 sec

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.35

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

➢ Tr=0.63 sec

➢ Peak overshoot: 4.2144 units

ww(ii)For unity feedback system having

w.E
Determine the type of system, error coefficients and the steady state error. BTL6 (8M)
r (t) = 1 + 3t + (t2/2).
Answer: Notes asy
En
➢ Steady state error constants: (4M)

2. gin
1. E(s) = R(s)/ 1+G(s) H(s).
R(s) =1/s + 3/s2+ ½ 1/s5

4. Kp= lt s→0 G(s)

ee
3. G(s)=5(s+1)/(s2(s+3) (s+10))

rin
5. Ki=Lt s→0 s G(s) g.n
6. Ka=Lt s→0 s2G(s)
➢ Steady state error:(4M)
et
1. Ess=1/1+Kp
2. Ess= 1/Kv
3. Ess=1/Ka

Explain how PI, PD and PID compensation will improve the time response of a system with
a neat block diagram and derivation. BTL 6 (15M)
5. Answer: Notes
➢ Transfer function of P & D Controller(4M)

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.36

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

U(s)/E(s) = Kp (1+Td S)
➢ Block diagram of PD Controller (3M)
➢ Compare with standard second order expression (3M)
Loop transfer function = Gc(s)G(s) / 1+ Gc(s)G(s)H(s)
= Kp (1+Td s) * {ɷn2/ s2+2ℇɷn s+ ɷn2.}
= ɷn2 (Kp+ Kd s) / (s2+ (2ℇɷn + Kdɷn2) s +Kp ɷn2)
➢ Justify the results(4M)

ww PD controller:
1. Addition of zero Increases the peak overshoot and reduces the rise time.

w.E2. Increased damping reduces the peak overshoot

(15M) BTL 6
Answer: Notes
asy
Derive the time response analysis of a first order system for step and ramp input.

En
gin
➢ Response of step and ramp input: (5M)

ee
1. Closed loop transfer function=> C(s)/R(s)= 1/1+Ts

6. 2. R(s)=1/s
3. C(s)=(1/T)/s(s+1/T) rin
➢ Inverse Laplace transform: (5M) g.n
C(t)=LT-1{C(s)}
➢ Compare with standard second order expression(5M)
et
G(s)=1/1+Ts

Sketch the root locus of the system having G(s) =K(s+9)/s(s2+4s+11). (Apr/May 2017).
BTL 5 (15M)
Answer: Page 4.75-Nagoor kani
7 ➢ Find poles and zeros (2M)
1.Poles=0, -2+j2.64, -2-j2.64 (n=3)
2.Zeros= -9 (m=1)

➢ Centroid and angle of asymptotes (3M)

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.37

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

1.centroid=sum of poles-sum of zeros/ n-m.

2. angle of asymptotes = +/- 1800 (2q+1)/ n-m.

➢ Find breakaway points (4M)

1.G(s)/ 1+G(s)
2. s(s2+4s+11) + K(s+9) =0
➢ Angle of departure(2M)
1.θd = 180-(angle subtended by poles to P2) + (angle subtended by zeros to P2)

➢ Find intersection of real axis with imaginary axis (4M)

1. s(s2+4s+11) + K(s+9) =0
2.s→ jw

ww
3. equate the real and imaginary parts
A unity feedback control system has an open loop transfer function
G(S) = K / s (s2+4s+13). Sketch the root locus.

w.E
BTL 4 (15M)
Answer: Page 4.75-Nagoor Kani
➢ Find poles and zeros (2M)

asy
1. Poles=0, -2+j3, -2-j3 (n=3)
2. Zeros= -9 (m=1)

En
➢ Centroid and angle of asymptotes (3M)

8 gin
1.centroid=sum of poles-sum of zeros/ n-m.
2. angle of asymptotes = +/- 1800 (2q+1)/ n-m.

➢ Find breakaway points (2M)

1.G(s)/ 1+G(s)
2. s(s2+4s+13) + K=0
ee rin
➢ Angle of departure(4M)
g.n
1.θd = 180-(angle subtended by poles to P2) +( angle subtended by zeros to P2)

➢ Find intersection of real axis with imaginary axis (4M)

1. s(s2+4s+13) + K=0
2. s→ jw
et
3. Equate the real and imaginary parts
A unity feedback control system has an open loop transfer function
G(S) = K(s+3) / s (s+1) (s+2) (s+4). Sketch the root locus. (nov/dec 2018) BTL 4 (15M)
Answer: Page 4.75-Nagoor Kani

9. ➢ Find poles and zeros (2M)

1. Poles=0, -1, -2, -4 (n=4)
2. Zeros= -3 (m=1)

➢ Centroid and angle of asymptotes (3M)

1.centroid=sum of poles-sum of zeros/ n-m.
JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.38

Downloaded From : www.EasyEngineering.net

 Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

2. angle of asymptotes = +/- 1800 (2q+1)/ n-m.

➢ Find breakaway points (4M)

1.G(s)/ 1+G(s)
2. s (s+1) (s+2) (s+4) +k(s+3) =0

➢ Angle of departure(2M)
1.θd = 180-(angle subtended by poles to P2) +( angle subtended by zeros to P2)

➢ Find intersection of real axis with imaginary axis (4M)

1. s (s+1) (s+2) (s+4) +k(s+3) =0
2. s→ jw

ww 3. Equate the real and imaginary parts

w.E UNIT III FREQUENCY RESPONSE

asy
Frequency response – Bode plot – Polar plot – Determination of closed loop response from open loop
response - Correlation between frequency domain and time domain specifications.

Q.No. En PART * A

Questions

gin
Define gain Margin. (May 03,11,13, Dec 06,08,09,11,12,14) (BTL1)
1.
ee
The gain margin (G.M.) is defined as the margin in gain allowable by which gain can be increased
till system reaches on the verge of instability. Mathematically it can be defined as reciprocal of the
magnitude of the G(jw)H(jw) measured at phase crossover frequency.
rin
2.
What is meant by frequency response? (April/May 17) (BTL1)
g.n
The magnitude and phase angle of sinusoidal transfer function of a system are real function of
frequency ω, and so they are called frequency response.

3.
Define phase margin. (Dec 03,06,08,09,10,11,12, May 03,11,12,13) (BTL1) et
The amount of additional phase lags which can be introduced in the system till the system reaches
on the verge of instability is called phase margin.

State any four-frequency domain specification. (Nov 08,10,15 May 07,11) (BTL1)
➢ Resonant Peak
➢ Resonant frequency
➢ Cutoff region
4.
➢ Phase Margin
➢ Gain Margin
➢ Phase cross over frequency
➢ Gain cross over frequency

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.39

Downloaded From : www.EasyEngineering.net

 Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

What are the advantages of Bode plot? (May 06, Dec 09,10) (BTL2)
➢ It shows both low and high frequency characteristics of transfer function in single
diagram.
➢ The plots can be easily constructed using some valid approximations.
➢ Relative stability of system can be studied by calculating G.M. and P.M. from the
5. ode plot.
➢ The various other frequency domain specifications like cut-off frequency,
bandwidth etc. can be determined.
➢ Data for constructing complicated polar and Nyquist plots can be easily obtained
from Bode plot.
➢ Transfer function of system can be obtained from the bode plot.

ww
What is gain crossover frequency and phase crossover frequency? (Dec 10, May 06,11, 14)
(BTL1)
➢ Gain crossover frequency (Wgc): The frequency at which magnitude of G(jw)H(jw) is unity
6.

w.E is called gain crossover frequency.

➢ Phase crossover frequency (Wpc): The frequency at which phase angle of G(jw)H(jw) is -
180 deg. is called phase crossover frequency.

asy
What is meant by corner frequency in frequency response analysis? (May 05) (BTL2)

En
A frequency up to which the magnitude contribution of a factor is negligible and can be neglected
7. is called its corner frequency. It is the frequency at which low frequency and high frequency

gin
asymptotes intersect each other. At the corner frequency, a change in the slope of a magnitude plot
occurs. Frequency range and the number of points is chosen automatically.

8. response. ee
What is the use of Nichol’s chart in control system? (Dec 14, May 15) (BTL2)
➢ Nichol’s chart used to find closed loop frequency response from open loop frequency

rin
➢ The frequency domain specifications can be determined from Nichols chart.

g.n
➢ The gain of the system can be adjusted to satisfy the given specifications.

9.
Define BIBO stability. (Dec 14) (BTL1)
et
A linear relaxed system is said to have BIBO stability if every bounded (finite) input results in a
bounded (finite) output.
What are the characteristics of phase lead network? (May 15) (BTL2)
➢ Increases system bandwidth which usually correlates to reduce rise and settling times and a
susceptibility to high frequency noise.
10.
➢ The phase of the forward path transfer function in the vicinity of the zero-gain crossover
frequency. This increases the phase margin of the closed loop system and hence the relative
stability.

What is the basis for selection of a compensator for a system? (May 15) (BTL2)
11. When the system is to be redesigned to meet the required specifications, it is necessary to alter the
system by adding an external device to it. The system must provide,
➢ Attenuation in the high frequency range to give a system enough phase margin.

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.40

Downloaded From : www.EasyEngineering.net

 Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

➢ Large bandwidth, short rise time and less settling time.

Define M & N circles. (BTL1)

➢ The magnitude of closed loop transfer function with unity feedback can be shown to be for
12. every value of M. These circles are called M circles.
➢ If the phase of closed loop transfer function with unity feedback is α, then tan α will be in
the form of circles for every value of α; these circles are called N circles.
How the resonant peak (Mr), resonant frequency (wr), and band width are determined from
Nichols chart? (BTL2)
The resonant peak is given by the value of µ. Contour which is tangent to G (jw) locus. The resonant
13. frequency is given by the frequency of G (jw) at the tangent point. The bandwidth is given by
frequency corresponding to the intersection point of G(jw) and –3dB M-contour.

14.
ww
What is meant by Cut of frequency? (BTL1)
it is denoted by ωb. the frequency at which the magnitude of the closed loop response is 3 dB down

w.E
from its zero-frequency value is called cut-off frequency.

What is meant by resonant peak? (BTL1)

15.
asy
Resonant peak (Mr): It is the maximum value of magnitude of the closed loop frequency
response.

En
What is meant by resonant frequency? (BTL1)

16. gin
Resonant frequency (ωr): The frequency at which resonant peak Mr occurs in closed loop frequency
response is called resonant frequency.

ee PART * B rin
g.n
Define all frequency domain specifications of a second order control system after plotting the
response. (Apr/May 2017).
Answer: Page 3.2-Nagoor kani
BTL1 (13M)
et
➢ Definition (5M) and Derivations of frequency domain frequency specifications: (8M)

1. Resonant peak:
1.
It is the peak (maximum) value of the magnitude of T(jw)T(jw). It is
denoted by Mr.

2. Resonant Frequency:
It is the frequency at which the magnitude of the frequency response has peak
value for the first time. It is denoted by ωr.
JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.41

Downloaded From : www.EasyEngineering.net

 Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

3. Cut off rate:

the slope of the log magnitude curve near the cut off frequency is called cut off rate
.
4. Band width:
The bandwidth is the range of frequencies in which the gain of the system is more
than -3dB.the frequency at which the gain is -3dB is called cut off frequency.
𝑤𝑏 = 𝑤𝑛[1 − 2𝜀 2 + √2 − 4𝜀 2 + 4𝜀 4 ]1/2
5. Gain margin:
The values of gain to be added to the system in order to bring the system to the verge

ww of instability.
1. Kg= 1/|G(jw)| Wpc

w.E 2. Kg in dB= 20 log Kg

6. Phase margin:
The additional phase lag to be added at the gain cross over frequency in order to bring

1. µ=1800+ɸgc
asy
my system to the verge of instability.

2. ɸgc = angle(G(jw)

En
Sketch the polar plot for a system whose open loop transfer function is 4/(s+2) (s+4). Find

Answer: Page.3.54- Nagoor kani gin

gain margin and phase margin. (Apr/May 2017). BTL3 (13M)

ee
➢ Convert G(s) into time constant form (3M)
1. G(s)=4/ (0.5s+1) (0.25s+1) rin
➢ S=jw (2M)
g.n
2.
1. G(jw)=4/(0.5jw+1) (0.25jw+1)
➢ Find magnitude and phase angle(2M) et
1. Magnitude = |G(jw)|
= 4/sqrt[(1+0.25w2) (1+0.625w2)]
2. Phase angle = angle of G(jw)
=-tan-1 (0.5)- tan-1 (0.25)
➢ Draw polar plot(4M)

➢ Find PM & GM (2M)

1. Gain margin:

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.42

Downloaded From : www.EasyEngineering.net

 Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

The values of gain to be added to the system in order to bring the system to the verge
of instability.
Kg= 1/|G(jw)| Wpc
Kg in dB= 20 log Kg
2. Phase margin:
The additional phase lag to be added at the gain cross over frequency in order to bring
my system to the verge of instability.
µ=1800+ɸgc ɸgc = angle(G(jw))

Consider a unity feedback open loop transfer function G(s) =100/s (1+0.1s) (1+0.2s). Draw

ww
the bode plot and find gain margin and stability of the system. (Nov/Dec 2016). BTL3 (13M)

w.E
Answer: Page 3.30-Nagoor Kani
➢ Convert G(s) into time constant form (3M)

asy
1. 100/s(1+0.1s) (1+0.2s)
➢ S= jw (2M)

En
1. G(jw)= 100/jw(1+0.1jw) (1+0.2jw)

gin
➢ Find magnitude and phase angle(2M)

3.
1. Magnitude = |G(jw)|
ee
2. Phase angle = angle of G(jw)
= -90-tan-1 (0.1)- tan-1 (0.2)
➢ Draw bode plot(4M) rin
➢ Find PM & GM(2M)
1. Gain margin: g.n
of instability.
Kg= 1/|G(jw)| Wpc
et
The values of gain to be added to the system in order to bring the system to the verge

Kg in dB= 20 log (Kg)

2. Phase margin:
The additional phase lag to be added at the gain cross over frequency in order to bring
my system to the verge of instability.
µ=1800+ɸgc ɸgc = angle(G(jw))

List any four frequency domain specifications. (May/June 2016). BTL1 (13M)
4.
Answer: Page 3.4- Nagoor Kani

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.43

Downloaded From : www.EasyEngineering.net

 Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

➢ Definition (5M) and Derivations of frequency domain frequency specifications: (8M)

1. Resonant peak:
It is the peak (maximum) value of the magnitude of T(jw)T(jw). It is
denoted by Mr.

2. Resonant Frequency:
It is the frequency at which the magnitude of the frequency response has peak
value for the first time. It is denoted by ωr.

ww
w.E3. Cut off rate:
the slope of the log magnitude curve near the cut off frequency is called cut off rate
.
4. Band width:
asy
The bandwidth is the range of frequencies in which the gain of the system is more

En
than -3dB.the frequency at which the gain is -3dB is called cut off frequency.
𝑤𝑏 = 𝑤𝑛[1 − 2𝜀 2 + √2 − 4𝜀 2 + 4𝜀 4 ]1/2

gin
Draw the bode magnitude and phase plot for the unity feedback system with G(s) =40/s
(1+0.1s) and hence determine phase margin and gain margin. (May/June 2016). BTL3
Answer: Page 3.32-Nagoor Kani ee
➢ Convert G(s) into time constant form (3M) rin
(13M)

1. 100/s(1+0.1s)
g.n
5.
➢ S= jw (2M)
2. G(jw)= 40/jw(1+0.1jw) et
➢ Find magnitude and phase angle(2M)
3. Magnitude = |G(jw)|
4. Phase angle = angle of G(jw)
= -90-tan-1 (0.1w)

➢ Draw bode plot(4M)

➢ Find PM & GM(2M)

1. Gain margin:

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.44

Downloaded From : www.EasyEngineering.net

 Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

The values of gain to be added to the system in order to bring the system to the verge
of instability.
Kg= 1/|G(jw)| Wpc
Kg in dB= 20 log Kg
2. Phase margin:
The additional phase lag to be added at the gain cross over frequency in order to bring
my system to the verge of instability.
µ=1800+ɸgc ɸgc = angle(G(jw)).

Sketch the bode plot for the following transfer function and determine the value of K for the

ww
gain cross over frequency of 5 rad/sec G(s) =ks2/ (1+0.2s) (1+0.02s). (Apr/May 2017). BTL3

w.E
Answer: Page 3.21-Nagoor Kani (13M)
➢ Convert G(s) into time constant form (3M)

asy
1. 100/s(1+0.1s) (1+0.2s)
➢ S= jw (2M)

En
2. G(jw)= K(jw)2/(1+0.2jw) (1+0.02jw)

gin
➢ Find magnitude and phase angle(2M)

6.
1. Magnitude = |G(jw)|
ee
2. Phase angle = angle of G(jw)
rin
= 180-tan-1 (0.2w)- tan-1 (0.02w)
➢ Draw bode plot (4M)
➢ Find PM & GM (2M) g.n
3. Gain margin: et
The values of gain to be added to the system in order to bring the system to the verge
of instability.
Kg= 1/|G(jw)| Wpc
Kg in dB= 20 log Kg
4. Phase margin:
The additional phase lag to be added at the gain cross over frequency in order to bring
my system to the verge of instability.
µ=1800+ɸgc ɸgc = angle(G(jw)).

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.45

Downloaded From : www.EasyEngineering.net

 Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

➢ Find the value of K

Sketch the polar plot for the following transfer function and determine the gain and phase
margin. G(s)=1/s(s+1) (1+2s). (Apr/May 2017) BTL3 (13M)
Answer: Page3.42-Nagoor kani
➢ Convert G(s) into time constant form (3M)
➢ G(s)=1/s(s+1) (1+2s)
➢ S=jw (2M)
G(jw)1/jw(jw+1) (2jw+1)

ww ➢ Find magnitude and phase angle(2M)

Magnitude = |G(jw)|

w.E Phase angle = angle of G(jw)

7.
asy
=90-tan-1 (w)- tan-1 (2w)
➢ Draw polar plot(4M)

➢ Find PM & GM (2M)

En
3. Gain margin: gin
of instability.
Kg= 1/|G(jw)| Wpc
ee
The values of gain to be added to the system in order to bring the system to the verge

rin
Kg in dB= 20 log Kg
g.n
4. Phase margin:
et
The additional phase lag to be added at the gain cross over frequency in order to bring
my system to the verge of instability.
µ=1800+ɸgc ɸgc = angle(G(jw))

Obtain the relationship between any three frequency domain specifications in terms of time
domain specifications. (Nov/Dec 2016). BTL4 (13M)
Answer: Page.3.7-Nagoor Kani
8.
➢ Calculate time domain specifications such as maximum overshoot, natural frequency,
damping ratio (4M)
1. Rise time definition

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.46

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

The time required for the response to rise from 0% to 100% of its final value. This is
applicable for the under-damped systems.

2. Peak time definition

The time required for the response to reach the peak value for the first time. It is denoted
by tp. At t=tp, the first derivate of the response is zero.

ww
w.E 3. Settling time definition and its formula
The time required for the response to reach the steady state and stay within the specified

asy
tolerance bands around the final value. The settling time is denoted by ts.

En
gin
4. Maximum overshoot definition and its formula
Peak overshoot Mp is defined as the deviation of the response at peak time from the final

ee
value of response. It is also called the maximum overshoot

rin
g.n
et
➢ Calculate frequency domain specifications such as resonant peak, damping ratio,
resonant frequency (4M)

5. Resonant peak:
It is the peak (maximum) value of the magnitude of T(jw)T(jw). It is
denoted by Mr.

6. Resonant Frequency:
It is the frequency at which the magnitude of the frequency response has peak
value for the first time. It is denoted by ωr.

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.47

Downloaded From : www.EasyEngineering.net

 Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

7. Cut off rate:

the slope of the log magnitude curve near the cut off frequency is called cut off rate
.
8. Band width:
The bandwidth is the range of frequencies in which the gain of the system is more
than -3dB.the frequency at which the gain is -3dB is called cut off frequency.
𝑤𝑏 = 𝑤𝑛[1 − 2𝜀 2 + √2 − 4𝜀 2 + 4𝜀 4 ]1/2
9. Gain margin:
The values of gain to be added to the system in order to bring the system to the verge

ww of instability.
1. Kg= 1/|G(jw)| Wpc

w.E 2. Kg in dB= 20 log Kg

10. Phase margin:

asy
The additional phase lag to be added at the gain cross over frequency in order to bring
my system to the verge of instability.
µ=1800+ɸgc
ɸgc = angle(G(jw) En
gin
➢ By using various values of damping ratio compare the results (5M)

ee rin
The closed loop transfer function of a system C(s)/R(s)=81/s2+7s+81 calculate the values of

g.n
resonant frequency, resonant peak and band width. (Nov/Dec 2015). BTL3 (13M)

➢ Resonant peak:
et
It is the peak (maximum) value of the magnitude of T(jw). It is
denoted by Mr.
9.

Ans:
➢ Resonant Frequency:
It is the frequency at which the magnitude of the frequency response has peak
value for the first time. It is denoted by ωr
wr= wn* sqrt(1-2ꜫ2)
Ans:

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.48

Downloaded From : www.EasyEngineering.net

 Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

➢ Band Width:
The bandwidth is the range of frequencies in which the gain of the system is more
than -3dB.the frequency at which the gain is -3dB is called cut off frequency.
𝑤𝑏 = 𝑤𝑛[1 − 2𝜀 2 + √2 − 4𝜀 2 + 4𝜀 4 ]1/2
Ans:

Explain how open loop response can be obtained from closed loop response. BTL 2 (13M)
Answer: Page 3.65-Nagoor Kani

ww ➢ Find magnitude of G(s)

1. The magnitude of closed loop transfer function with unity feedback can be shown to be for
every value of M. These circles are called M circles.
10.
w.E2. If the phase of closed loop transfer function with unity feedback is α, then tan α will be in
the form of circles for every value of α; these circles are called N circles.

asy
➢ Convert into in the form of circle equation

En
➢ Find phase angle of G(s) and Find α

gin PART * C

Answer: Page3.45-Nagoor kani

ee
Sketch the polar plot for the following transfer function and determine the gain and phase
margin. G(s)=1/s2(s+1) (1+2s). (Apr/May 2017) BTL3 (13M)

rin
➢ Convert G(s) into time constant form (3M)
g.n
➢ G(s)= 1/s2(s+1) (1+2s).
➢ S=jw (2M) et
1. G(jw)=1/(jw)2(jw+1) (2jw+1)
➢ Find magnitude and phase angle(2M)
Magnitude = |G(jw)|
Phase angle = angle of G(jw)
=90-tan-1 (w)- tan-1 (2w)
➢ Draw polar plot(4M)

➢ Find PM & GM (2M)

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.49

Downloaded From : www.EasyEngineering.net

 Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

5. Gain margin: - Kg=0

The values of gain to be added to the system in order to bring the system to the verge
of instability.
Kg= 1/|G(jw)| Wpc
Kg in dB= 20 log Kg
6. Phase margin: PM= -900
The additional phase lag to be added at the gain cross over frequency in order to bring
my system to the verge of instability.

ww µ=1800+ɸgc ɸgc = angle(G(jw))

Sketch the polar plot for the following transfer function and determine the gain and phase

w.E
margin. G(s)=(1+0.2s) (1 +0.025s)/s3(0.005s+1) (1+0.001s).
(13M)
(Apr/May 2017) BTL3

asy
Answer: Page3.48-Nagoor kani
➢ Convert G(s) into time constant form (3M)

En
➢ G(s)=(1+0.2s) (1 +0.025s)/s3(0.005s+1) (1+0.001s).
➢ S=jw (2M)
gin
ee
G(jw)=(1+0.2jw) (1 +0.025jw)/(jw)3(0.005jw+1) (1+0.001jw).
➢ Find magnitude and phase angle(2M)
Magnitude = |G(jw)|
rin
2. Phase angle = angle of G(jw)
g.n
=90-tan-1 (w)- tan-1 (2w)
➢ Draw polar plot(4M)

➢ Find PM & GM (2M)

et
7. Gain margin: - Kg=0
The values of gain to be added to the system in order to bring the system to the verge
of instability.
Kg= 1/|G(jw)| Wpc
Kg in dB= 20 log Kg
8. Phase margin: PM= -770
The additional phase lag to be added at the gain cross over frequency in order to bring
my system to the verge of instability.

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.50

Downloaded From : www.EasyEngineering.net

 Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

µ=1800+ɸgc ɸgc = angle(G(jw))

Sketch the polar plot for the following transfer function and determine the gain and phase
margin. G(s)=1/s(s+1)2. (Apr/May 2017) BTL3 (13M)
Answer: Page3.51-Nagoor kani
➢ Convert G(s) into time constant form (3M)
➢ G(s)=1/s(s+1)2
➢ S=jw (2M)
3.
G(s)=1/jw(jw+1)2.

ww ➢ Find magnitude and phase angle(2M)

Magnitude = |G(jw)|

w.E Phase angle = angle of G(jw)

asy
=90-tan-1 (w)- tan-1 (2w)
➢ Draw polar plot(4M)

➢ Find PM & GM (2M)

En
gin
9. Gain margin: - Kg=2
The values of gain to be added to the system in order to bring the system to the verge
of instability.
Kg= 1/|G(jw)| Wpc
Kg in dB= 20 log Kg
ee rin
10. Phase margin: PM= 210
g.n
The additional phase lag to be added at the gain cross over frequency in order to bring
my system to the verge of instability.
µ=1800+ɸgc ɸgc = angle(G(jw))
et
Sketch the Nyquist plot for the system whose loop transfer function is
G(s)H(s)=K(s+2)/[s(s+3) (s+6)] and find the range of K for stability of closed loop. Check your
answer with Routh’s Criterion. Nov/Dec 2018 BTL 5 15M
Answer: Page3.58-Nagoor kani
5.
➢ Put K=1
➢ Convert G(s) into time constant form (3M)
➢ G(s)H(s)=(s+2)/[s(s+3) (s+6)]

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.51

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

➢ S=jw (2M)
G(s)H(s)=(s+2)/[s(s+3) (s+6)].
➢ Find magnitude and phase angle(2M)
Magnitude = |G(jw)|
Phase angle = angle of G(jw)
➢ Draw polar plot(4M)

➢ Find PM & GM (2M)

11. Gain margin: - Kg=2

ww The values of gain to be added to the system in order to bring the system to the verge
of instability.

w.E Kg= 1/|G(jw)| Wpc

Kg in dB= 20 log Kg

asy
12. Phase margin: PM= 210
The additional phase lag to be added at the gain cross over frequency in order to bring

µ=1800+ɸgc En
my system to the verge of instability.
ɸgc = angle(G(jw))

gin
Sketch the bode plot for the following transfer function G(s)=75(1+0.2s)/s(s 2+16s+100).
(Apr/May 2017). BTL3
Answer: Page 3.24-Nagoor Kani (13M)
ee rin
➢ Convert G(s) into time constant form (3M)
1. G(s)=75(1+0.2s)/s(s2+16s+100). g.n
6
2. S= jw (2M)
3. G(jw)= 75(1+0.2jw)/jw(jw2+16jw+100)
➢ Find magnitude and phase angle(2M)
et
1. Magnitude = |G(jw)|
2. Phase angle = angle of G(jw)
= tan-1 (0.2w)-90- tan-1 ((0.16w)/(1-0.01w2))
➢ Draw bode plot (4M)
➢ Find PM & GM (2M)

Gain margin: - Kg = infinity

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.52

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

The values of gain to be added to the system in order to bring the system to the verge
of instability.
Kg= 1/|G(jw)| Wpc
Kg in dB= 20 log Kg
5. Phase margin=920
The additional phase lag to be added at the gain cross over frequency in order to bring
my system to the verge of instability.
µ=1800+ɸgc ɸgc = angle(G(jw)).

Sketch the bode plot for the following transfer function G(s)=20/s(1+3s) (1+4s). obtain the

ww
gain cross over and phase cross over frequency. BTL 4 (15M)

w.E
Answer: Page 3.32-Nagoor Kani
➢ Convert G(s) into time constant form (3M)

asy
1. G(s)=20/s(1+3s) (1+4s).
2. S= jw (2M)

En
3.G(jw)=20/jw(1+3jw) (1+4jw).
7
gin
➢ Find magnitude and phase angle(4M)
1. Magnitude = |G(jw)|
ee
2. Phase angle = angle of G(jw)
rin
= -tan-1 (3w)-90- tan-1 (4w)
➢ Draw bode plot (4M) g.n
➢ Find Wgc and Wpc (4M)
Wgc=1.1 rad/sec
Wpc=0.25 rad/sec
et

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.53

Downloaded From : www.EasyEngineering.net

 Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

UNIT IV STABILITY AND COMPENSATOR DESIGN

Characteristics equation – Routh Hurwitz criterion – Nyquist stability criterion- Performance criteria -
Effect of Lag, lead and lag-lead compensation on frequency response–Design of Lag, lead, Lag/Lead
compensator design using bode plots.
PART * A

Q.No. Questions

What is characteristics equation. (APRIL/MAY 17) (BTL1)

1.
The denominator polynomial of C(s) / R(s) is the characteristics equation of the system.

State what is stability in control system (BTL1)

2.
wwA linear relaxed system is said to have BIBIO stability if every bounded input result in abounded
output.

w.E
What will be the nature of impulse response when the roots of characteristic equation are
lying on imaginary axis? (BTL2)

asy
3.
If the root of characteristic equation lies on imaginary axis the nature of impulse response is
oscillatory.

En
What is the relationship between Stability and coefficient of characteristic polynomial?

4.
(BTL3)
gin
If the coefficient of characteristic polynomial is negative or zero, then some of the roots lie on the

ee
negative half of the S-plane. Hence the system is unstable. If the coefficients of the characteristic
polynomial are positive and if no coefficient is zero, then there is a possibility of the system to be
stable provided all the roots are lying on the left half of the S-plane
rin
Write Routh stability criterion? (BTL2)
g.n
5.
et
Routh criterion states that the necessary and enough condition for stability is that all the elements
in the first column of the Routh array is positive. If this condition is not met, the system is unstable
and the number of sign changes in the elements of the first column of Routh array corresponds to
the number of roots of characteristic equation in the right half of the S-plane.

What is limitedly stable system? (BTL2)

6. For a bounded input signal if the output has constant amplitude oscillations, then the system may
be stable or unstable under some limited constraints such a system is called limitedly stable
system.

In Routh array what conclusion you can make when there is a row of all zeros? (BTL2)
7. All zero rows in the Routh array indicate the existence of an even polynomial as a factor of the
given characteristic equation. The even polynomial may have roots on imaginary axis

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.54

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

What is a principle of argument? (BTL2)

The principles of arguments state that, Let F(S) are analytic function and if an arbitrary closed
8. contour in a clockwise direction is chosen in the S-plane so that F(S) is analytic at every point of
the contour. Then the corresponding F(S) plane contour mapped in the F(S) plane will encircle
the origin N times in the anti-clockwise direction, where N is the difference between number of
poles and zeros of F(S) that are encircled by the chosen closed contour in the S plane.

How the roots of characteristic are related to stability? (BTL1)

9. If the root of characteristic equation has positive real part, then the impulse response of the system
is not bounded. Hence the system will be unstable. If the root has negative real parts, then the
impulse response is bounded. Hence the system will be stable.

ww
What is the necessary condition for stability? (BTL1)

10.
w.E
The necessary condition for stability is that all the coefficients of the characteristic polynomial be
positive. The necessary and enough condition for stability is that all the elements in the first
column of the Routh array should be positive.

asy
State the requirements for BIBO Stability. (BTL2)
11.
En
The requirements of the BIBO stability is that the absolute integral of the impulse response of the
system should take only the finite value.

gin
What is auxiliary polynomial? (BTL2)

12. ee
In the construction of Routh array a row of all zero indicates the existence of an even polynomial

rin
as a factor of given characteristic equation. In an even polynomial the exponents of S are even
integers or zero only. This even polynomial factor is called auxiliary polynomial. The coefficients

g.n
of auxiliary polynomial are given by the elements of the row just above the row of all zeros.

Why compensation is required in feedback control systems? (BTL4)

et
In feedback control systems compensation is required in the following situations:
➢ When the system is unstable, then compensation is required to stabilize the system and to
13.
meet the desired performance.
➢ When the system is stable, compensation is provided to obtain desired performance.

When lag, lead, lag-lead compensation is employed? (BTL4)

➢ Lag compensation is employed for a stable system for improvement in steady state
14. performance.
➢ Lead compensation is employed for stable/unstable system for improvement in transient
state performance.

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.55

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

➢ Lag-lead compensation is employed for stable/unstable system for improvement in both

steady state and transient state performance.

Discuss the effect of adding a pole to open loop transfer function of a system. (BTL2)
15. The addition of pole to open loop transfer function of a system will reduce the steady state error.
The closer the pole to origin lesser will be the steady state error. Thus, the steady state performance
of the system is improved. Also, the addition of pole will increase the order of the system, which
in turn makes the system less stable than the original system.

Discuss the effect of adding a zero to open loop transfer function of a system. (BTL2)
The addition of zero to open loop transfer function of a system will improve the transient response.
16.
ww
The addition of zero reduces the rise time. If the zero is introduced close to origin the peak
overshoot will be large. If the zero is introduced far away from the origin in the left half of s plane,
then the effect of zero on the transient response will be negligible.

w.E
What are the characteristics of lag compensator? (BTL2)

17.
asy
The lag compensator improves the steady state performance, reduces the bandwidth and increases
the rise time (which results in slower transient response). If the pole introduced by the

En
compensator is not cancelled by a zero in the system, then the lag compensator increases the order
of the system by one.

gin
Write the characteristics of lead compensator. (BTL2)

18.
ee
The lead compensation increases the bandwidth and improves the speed of response. It also
reduces the peak overshoot. If the pole introduced by the compensator is not cancelled by a zero

rin
in the system, then lead compensation increases the order of the system by one. When the given
system is stable/unstable and improvement in transient state response then lead compensation is
employed.
g.n
19.
What is the transfer function of lag, lead and lag-lead compensator? (BTL2)
Gc(s)=(s+1/T)/(s+1/Tβ)
Gc(s)=(s+1/T)/(s+1/Tα)
et
Gc(s)=(s+1/T1) (s+1/T2)/(s+1/T1β) (s+1/ T2α)

State about lead-lag compensator. (APRIL/MAY 17) (BTL2)

The lead-lag compensation is a design procedure in which a lead-lag compensator is introduced
20. in the system to meet the desired specifications.

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.56

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

Define Nyquist stability criterion. (May 17, 13, Dec 15) (BTL1)
If the Nyquist plot of the open loop tf G(s) H(s) corresponding to the Nyquist contour in the s-
21
plane encircles the critical point -1+j0 in the counter clockwise direction as many times as the
number of right half s-plane poles of G(s)H(s), the closed loop system is stable.

PART * B

Draw the Nyquist plot for the system whose open loop transfer function is G(S)H(S) =K/S
(S+2) (S+10). Determine the range of K for which closed loop system is stable. BTL3 (13M)
Answer: Page 4.35- Nagoor Kani
➢ Convert G(s) into time constant form (2M)

ww 1.G(s)H(s)= K/s(0.5s+1) (0.1s+1)

➢ Select contour regions (3M)

w.E 1.System has one pole at origin.

1. asy
2.Select S-plane enclosing entire right half except the origin.
➢ Apply four sections and draw the F(s) contour (4m)

En
1.Four sections C1, C2, C3 and C4.

gin
➢ Finally draw all contour regions in single Nyquist plot (4m)
1. Stability:
-0.00417k = -1
K=240 ee
This contour passes through the point -1+j0 rin
2. K<240:
The closed loop system is stable
g.n
3. K>240
The closed loop system is unstable.
et
Construct Nyquist plot for a feedback control system whose open loop transfer function is
given by G(S)H(S) =K(1+s)2/ s3. Comment on the stability of open loop and closed loop
transfer function. BTL3 (13M)
Answer: Page 4.38-Nagoor kani
2.
➢ Convert G(s) into time constant form (2M)
1. G(s)H(s)= K(1+s)2/ s3
2. G(jw)H(jw)= K(1+jw)2/(jw)3
➢ Select contour regions (3M)

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.57

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

1. System has three poles at origin.

2.Select S-plane enclosing entire right half except the origin.
➢ Apply four sections and draw the F(s) contour (4m)
1.Four sections C1, C2, C3 and C4.
➢ Finally draw all contour regions in single Nyquist plot (4m)
1. Stability:
-2k = -1
K=0.5

ww This contour passes through the point -1+j0

2. K<0.5:
The closed loop system is Unstable

w.E
3. K>0.5
The closed loop system is stable.

asy
Sketch the Nyquist plot for a system with the open loop transfer function G(S)H(S) =(1+4S)
/s2 (1+S) (2S+1). Determine the stability of the system. BTL3 (13M)
Answer: Page 4.42-Nagoor Kani
En
gin
➢ Convert G(s) into time constant form (2M)
3. G(s)H(s)= (1+4S) /s2 (1+S) (2S+1)

➢ Select contour regions (3M) ee

4. G(jw)H(jw)= (1+4jw)/jw2(1+jw) (2jw+1)

rin
3. 1. System has two poles at origin.
g.n
2.Select S-plane enclosing entire right half except the origin.
➢ Apply four sections and draw the F(s) contour (4M)
1.Four sections C1, C2, C3 and C4.
et
➢ Finally draw all contour regions in single Nyquist plot (4M)
1.closed loop system is unstable
2.Two poles of closed loop system are lying on the right half of s plane.

Construct Routh array and determine the stability of the system represented by the
4. characteristics equation S5+S4+2S3+2S2+3S+5=0.Comment on the location of the roots of
characteristic equation. BTL2 (13M)

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.58

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

Answer: Page 4.14-Nagoor kani

➢ Form Routh array from Characteristic equation (5M)
➢ Check the first column of the Routh array (5M)
1. If it is positive, system is stable
2. If it is not positive, system is unstable

➢ Sign changes in first column (3M)

1. All are negative→all roots on left half
2. Sign changes→ corresponds to roots in right half

ww
Construct Routh array and determine the stability of the system represented by the
characteristics equation S7+9S6+24S4+24S3+24S2+23S+15=0comment on the location of the
roots of characteristic equation. BTL2 (13M)

w.E
Answer: Page 4.16-Nagoor kani

asy
➢ Form Routh array from Characteristic equation (5M)
➢ Check the first column of the Routh array (5M)
5.
En
1.If it is positive, system is stable

gin
2.If it is not positive, system is unstable

ee
➢ Sign changes in first column (3M)
1.All are negative→all roots on left half
rin
2.Sign changes→ corresponds to roots in right half

g.n
The open loop transfer function of a unity feedback control system is G(s)=K/[s(s+1) (s+2)].

et
Design a suitable Lag-lead compensator to meet the following specifications: static velocity
error constant Kv=10 sec-1, phase Margin = 50 degree and gain margin >= 10db.
BTL 5 (13M)
Answer Page.5.61-Nagoor kani
Bode plot: 5M
6. Procedure: 4M
Compensated bode plot:4M
➢ Find the value of K using velocity error constant

➢ Convert G(s) into time constant form

➢ S=jw
JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.59

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

➢ Find magnitude and phase angle

➢ Draw bode plot

➢ Find PM & GM

➢ If the PM is not matched with the given specifications, lag lead compensator is
employed

➢ Using design procedure of lag- lead compensator find compensator transfer

function

ww Find overall transfer function

w.E
Consider the unity feedback whose open loop transfer function is G(s)=K/[s(0.1s+1)
(0.2s+1)] system to be compensated to meet the following specifications: static velocity
error constant = 30 sec-1, phase margin>=50 degrees. Band width (wb)=12 rad /sec.
BTL 6 (13M)

asy
Answer: Page 5.37-Nagoor kani
Bode plot: 5M
En
Procedure: 4M
Compensated bode plot:4M gin
ee
➢ Find the value of K using velocity error constant

➢ Convert G(s) into time constant form rin

7.
➢ S=jw g.n
➢ Find magnitude and phase angle

➢ Draw bode plot

et
➢ Find PM & GM

➢ If the PM is not matched with the given specifications, lead compensator is

employed

➢ Using design procedure of lead compensator find compensator transfer function

➢ Find overall transfer function.

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.60

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

Construct Routh array and determine the stability of the system represented by the
characteristics equation S4+8S3+18S2+16S+5=0.Comment on the location of the roots of
characteristic equation. BTL2 (13M)
Answer: Page 4.13-Nagoor Kani
➢ Form Routh array from Characteristic equation (5M)

8. ➢ Check the first column of the Routh array (5M)

1.If it is positive, system is stable

ww 2.If it is not positive, system is unstable

➢ Sign changes in first column (3M)

w.E 1.All are negative→all roots on left half

asy
2.Sign changes→ corresponds to roots in right half

Construct Routh array and determine the stability of the system represented by the

En
characteristics equation S6+2S5+8S4+12S3+20S2+16S+16=0.Comment on the location of the
roots of characteristic equation. BTL2 (13M)
Answer: Page 4.13-Nagoor Kani
gin
9.
ee
➢ Form Routh array from Characteristic equation (5M)
➢ Check the first column of the Routh array (5M)
rin
g.n
1.If it is positive, system is stable
2.If it is not positive, system is unstable
➢ Sign changes in first column (3M)
1.All are negative→all roots on left half
et
2.Sign changes→ corresponds to roots in right half

Construct Routh array and determine the stability of the system represented by the
characteristics equation S6+S5+3S4+3S3+3S2+2S+1=0.Comment on the location of the roots
of characteristic equation. BTL2 (13M)
10. Answer: Page 4.20-Nagoor Kani
➢ Form Routh array from Characteristic equation (5M)
➢ Check the first column of the Routh array (5M)

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.61

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

1.If it is positive, system is stable

2.If it is not positive, system is unstable
➢ Sign changes in first column (3M)
1.All are negative→all roots on left half
2.Sign changes→ corresponds to roots in right half

PART * C

A unity feedback system has an OLTF G(s) = K / s(s+0.5). Design a Lead-Lag compensator
is to meet the following specifications. ζ= 0.5, Wn=5 rad/sec, velocity error constant, Kv =

ww
80. BTL3
Answer Page.5.61-Nagoor kani
(15M)

w.E
Bode plot: 5M
Procedure: 4M
Compensated bode plot:4M
asy
➢ Find the value of K using velocity error constant

En
➢ Convert G(s) into time constant form

1. ➢ S=jw gin
ee
➢ Find magnitude and phase angle
rin
➢ Draw bode plot

➢ Find PM & GM g.n

et
➢ If the PM is not matched with the given specifications, lag lead compensator is
employed

➢ Using design procedure of lag- lead compensator find compensator transfer

function

➢ Find overall transfer function

Consider the unity feedback system whose OLTF is G(s) = K / s (s+3) (s+6). Design a lag-
lead compensator to meet the following specifications. (i) Velocity error constant, Kv = 80,
2. (ii) P.M 35º BTL 3 (15M)
Answer: Page 5.55- Nagoor kani
Bode plot: 5M

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.62

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

Procedure: 4M
Compensated bode plot:4M
➢ Find the value of K using velocity error constant

➢ Convert G(s) into time constant form

➢ S=jw

➢ Find magnitude and phase angle

➢ Draw bode plot

ww ➢ Find PM & GM

w.E ➢ If the PM is not matched with the given specifications, lag lead compensator is
employed

asy
➢ Using design procedure of lag- lead compensator find compensator transfer
function

En
➢ Find overall transfer function

gin
Draw the frequency response of lag compensator with necessary expressions. BTL 3 (13M)
Answer: Page 5.5-Nagoor Kani
ee
➢ G(s), s can be replaced by jw (4M)
rin
3. 1. 𝐺𝑐 (𝑠) =
(𝑠+1/𝑇)
1 g.n
2. 𝐺𝑐 (𝑠) =
(𝑠+
𝛽𝑇

(𝑗𝑤+1/𝑇)
)

1
et
(𝑗𝑤+ )
𝛽𝑇

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.63

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

➢ Find magnitude and Phase angle. (4M)

ww 𝐺𝑐(𝑗𝑤) =
1 + 𝑗𝑤𝑇
=
√1 + (𝑤𝑇)2 < 𝑡𝑎𝑛−1 𝑤𝑇

w.E 1 + 𝑗𝑤𝛽𝑇 √1 + (𝑤𝛽𝑇)2 < 𝑡𝑎𝑛−1 𝑤𝛽𝑇

➢ Draw the graph between frequency versus phase angle (5M)

asy
➢ Draw the graph between frequency versus magnitude

En
gin
ee rin
g.n
et
Draw the frequency response of lead compensator with necessary expressions. BTL4 (15M)
4. Answer: Page.5.28-Nagoor Kani
➢ G(s), s can be replaced by jw (4M)

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.64

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

(𝑠+1/𝑇)
1. 𝐺𝑐 (𝑠) = 1
(𝑠+𝛼𝑇)

(𝑗𝑤+1/𝑇)
2. 𝐺𝑐 (𝑠) = 1
(𝑗𝑤+ )
𝛼𝑇

ww
w.E ➢ Find magnitude and Phase angle
asy 1 + 𝑗𝑤𝑇 √1 + (𝑤𝑇)2 < 𝑡𝑎𝑛−1 𝑤𝑇

En
𝐺𝑐 (𝑗𝑤) = =
1 + 𝑗𝑤𝛼𝑇 √1 + (𝑤𝛼𝑇)2 < 𝑡𝑎𝑛−1 𝑤𝛼𝑇

gin
➢ Draw the graph between frequency versus phase angle

ee
➢ Draw the graph between frequency versus magnitude

rin
g.n
et

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.65

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

Draw the frequency response of lead lag compensator with necessary expressions.
BTL4(15M)
Answer: Page 5.28 – Nagoor Kani
➢ G(s), s can be replaced by jw (4M)
(𝑠+1/𝑇1) (𝑠+1/𝑇2)
3. 𝐺𝑐 (𝑠) = 1 1
(𝑠+𝛽𝑇1) (𝑠+𝛼𝑇2)

(𝑗𝑤+1/𝑇1) (𝑗𝑤+1/𝑇2)
4. 𝐺𝐺𝑐 (𝑠) = 1 1

ww (𝑗𝑤+𝛽𝑇1) (𝑗𝑤+𝛼𝑇2)

w.E
5
asy
En
gin
ee
➢ Find magnitude and Phase angle. (4M)
1 + 𝑗𝑤𝑇1 1 + 𝑗𝑤𝑇2 rin
𝐺𝑐(𝑗𝑤) =
1 + 𝑗𝑤𝛽𝑇1 1 + 𝑗𝑤𝛼𝑇2
√1 + (𝑤𝑇1)2 < 𝑡𝑎𝑛−1 𝑤𝑇1 g.n
√1 + (𝑤𝑇2)2 < 𝑡𝑎𝑛−1 𝑤𝑇2
=
et
√1 + (𝑤𝛽𝑇1)2 < 𝑡𝑎𝑛−1 𝑤𝛽𝑇1 √1 + (𝑤𝛼𝑇2)2 < 𝑡𝑎𝑛−1 𝑤𝛼𝑇2

➢ Draw the graph between frequency versus phase angle (5M)

➢ Draw the graph between frequency versus magnitude (2M)

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.66

Downloaded From : www.EasyEngineering.net

 Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

UNIT –V STATE VARIABLE ANALYSIS

Concept of state variables – State models for linear and time invariant Systems – Solution of state and
output equation in controllable canonical form – Concepts of controllability and observability.
PART * A

Q.No. Questions

What are the advantages of state space analysis? (BTL2)

➢ It can be applied to non-linear as well as time varying systems.
1. ➢ Any type of input can be considered for designing the system.
➢ It can be conveniently applied to multiple input multiple output systems.

2. ww ➢ The state variables selected need not necessarily be the physical quantities of the system.
What are phase variables? (BTL1)
The phase variables are defined as the state variables which are obtained from one of the system

3.
w.E
variables and its derivatives.
Define state variable. (BTL1)
The state of a dynamical system is a minimal set of variables (known as state variables) such that

asy
the knowledge of these variables at t-t0 together with the knowledge of the inputs for t > t0,
completely determines the behavior of the system for t > t0.

En
Write the general form of state variable matrix. (BTL1)
The most general state-space representation of a linear system with m inputs, p outputs and n state

gin
variables are written in the following form:
Ẋ= AX + BU
4.
Y = CX + DU
Where = state vector of order n X1.
U = input vector of order n X1.
A=System matrix of order n Xn.
ee rin
B=Input matrix of order n Xm
C =output matrix of order p Xn g.n
5.
D = transmission matrix of order p Xm.
et
What is the necessary condition to be satisfied for design using state feedback? (BTL2)
The state feedback design requires arbitrary pole placements to achieve the desire performance.
The necessary and enough condition to be satisfied for arbitrary pole placement is that the system
is completely state controllable.

What is controllability? (BTL1)

6. A system is said to be completely state controllable if it is possible to transfer the system state
from any initial state X(t0) at any other desired state X(t), in specified finite time by a control
vector U(t).
What is observability? (BTL1)
7. A system is said to be completely observable if every state X(t) can be completely identified by
measurements of the output Y(t) over a finite time interval.
8. What is similarity transformation? (BTL2)
The process of transforming a square matrix A to another similar matrix B by a transformation
JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.67

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

P- |AP| = B is called similarity transformation. The matrix P is called transformation matrix.

What is meant by diagonalization? (BTL2)

9. The process of converting the system matrix A into a diagonal matrix by a similarity
transformation using the modal matrix M is called diagonalization.

What is modal matrix? (BTL2)

The modal matrix is a matrix used to diagonalize the system matrix. It is also called
diagonalization matrix.
10. If A = system matrix
M = Modal matrix
And M-1=inverse of modal matrix

ww
Then M-1AM will be a diagonalized system matrix

How the modal matrix is determined? (BTL2)

11.
w.E
The modal matrix M can be formed from eigenvectors. Let m1, m2, m3 …. mn be the eigen
vectors of the nth order system. Now the modal matrix M is obtained by arranging all the
eigenvectors column wise as shown below.

asy
Modal matrix, M = [m1, m2, m3 …. mn].
What is the need for controllability test? (BTL2)

12.
En
The controllability test is necessary to find the usefulness of a state variable. If the state variables
are controllable then by controlling (i.e. varying) the state variables the desired outputs of the
system are achieved.
gin
What is the need for observability test? (BTL2)
The observability test is necessary to find whether the state variables are measurable or not. If the
13.
ee
state variables are measurable then the state of the system can be determined by practical
measurements of the state variables.
rin
State the condition for controllability by Gilbert’s method. (BTL2)
Case (i) when the Eigen values are distinct
g.n
Consider the canonical form of state model shown below which is obtained by using the
transformation X=MZ.
Ẋ= ΛZ + U
Y=Z + DU
et
Where, Λ = M-1AM; = CM, = M-1B and M = Modal matrix.
14. In this case the necessary and enough condition for complete controllability is that, the matrix
must have no row with all zeros. If any row of the matrix is zero, then the corresponding state
variable is uncontrollable.
Case (ii) when Eigen values have multiplicity
In this case the state modal can be converted to Jordan canonical form shown below:
Z= JZ + U
Y=Z + DU Where, J = M-1AM
In this case the system is completely controllable, if the elements of any row of that correspond
to the last row of each Jordan block are not all zero.

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.68

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

State the condition for observability by Gilbert’s method. (BTL2)

Consider the transformed canonical or Jordan canonical form of the state model shown below:
which is obtained by using the transformation, X =MZ
Z= ΛZ + U
Y=Z + DU (Or)
15. Z= JZ + U
Y=Z + DU where =CM and M=modal matrix.
The necessary and enough condition for complete observability is that none of the columns of the
matrix be zero. If any of the column has all zeros, then the corresponding state variable is not
observable.

State the duality between controllability and observability. (BTL2)

16. ww
The concept of controllability and observability are dual concepts and it is proposed by Kalman
as principle of duality. The principle of duality states that a system is completely state controllable

w.E
if and only if its dual system is completely state controllable if and only if its dual system is
completely observable or vice versa.

Define servo mechanism. (BTL 1)

17.
asy
The servomechanism is a feedback control system, in which the output is mechanical position or
time derivatives of positions.

En
what is state diagram? Draw the block diagram representation of state model.
The pictorial representation of the state model of the system is called state diagram. The state

gin
diagram of the system can be either in block diagram or in signal flow graph form.

18.
ee rin
g.n
et
What is state vector? (BTL 1)
19. The state vector is a (n x1) column matrix whose elements are state variables of the system.it is
denoted by X(t).
20. Write the properties of state transition matrix.

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.69

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

1. (0) = I
2.  −1 (t ) = (−t )
3. x(0) = (−t ) x(t )
4. (t 2 − t1 ) (t1 − t0 ) = (t 2 − t0 )
(t ) = (kt )
k
5.

PART * B

Determine the state model of armature-controlled DC motor. BTL1 (13M)

ww
Answer: Page 2.26-Nagoor kani.
➢ Draw the electrical circuit (3M)

w.E
asy
En
gin
1. ee rin
g.n
➢ Write differential equations in terms of displacement (3M)

𝑉𝑎 = 𝑖𝑎 𝑅𝑎 + 𝐿𝑎
𝑑𝑖𝑎
+ 𝑒𝑏
et
𝑑𝑡

𝑑2 𝜃 𝑑𝜃
𝑇 = 𝐽 𝑑𝑡 2 + 𝐵 𝑑𝑡

➢ Apply the state variables to differential equation (2M)

𝑑𝜃
𝑥1 = 𝑖𝑎 ; 𝑥2 = =𝜔 ; 𝑥3 = 𝜔
𝑑𝑡

➢ Rearrange the equation and derive state model (2M)

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.70

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

̇ 𝑅𝑎 𝐾𝑏 1
𝒙𝟏 = − 𝑥1 − 𝑥2 + 𝑢
𝐿𝑎 𝐿𝑎 𝐿𝑎
̇ 𝐾𝑡 𝐵
𝒙𝟐 = − 𝑥1 − 𝑥2
𝐽 𝐽
𝒙̇ 𝟑 = 𝑥2
➢ Draw the block diagram for state equation and output equation (3M)

Construct the state model for a system characterized by the differential equation
d3y/dt3+6d2y/dt2+11dy/dt+6y+u=0.Give the block diagram representation of the state model.
BTL3 (13M)

ww
Answer: Page: 6.26-Nagoor kani

w.E
➢ Convert differential equations in to dot variables (2M)
𝑥1 = 𝑦

𝑥2 =
𝑑𝑦
𝑑𝑡 asy
= 𝑥1̇ 𝑥2 =
𝑑2 𝑦
𝑑𝑡 2
= 𝑥2̇

En
2.

gin
➢ Apply the state variables to dot variables (2M)

1. 𝑥̇ 1 = 𝑥2

2. ̇ 𝑥2 = 𝑥3 ee
3. 𝑥3̇ =− 6𝑥1 − 11𝑥2 − 6𝑥3 − 𝑢
rin
➢ Rearrange the equation and derive state model (3M)
➢ Draw the block diagram for state equation and output equation (6M) g.n
Y(s)/U(s) =10/s3+4s2+2s+1. BTL3 (13M)
et
Obtain the state model of the system whose open loop transfer function is given as,

Answer: Page: 6.29-Nagoor kani

➢ Use inspection, cascade, signal flow graph method (1M)
3.
➢ Take inverse Laplace transform & Convert differential equations in to dot variables (2M)
➢ Apply the state variables to dot variables (2M)
➢ Rearrange the equation and derive state model (3M)
➢ Draw the block diagram for state equation and output equation (5M)

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.71

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

A feedback system has a closed loop transfer function Y(s)/U(s) = 10(s+4)/s(s+1) (s+3),
construct block diagram representation of each state model. BTL3 (13M)
Answer: Page: 6.23-Nagoor kani
➢ Use inspection, cascade, signal flow graph method (1M)
4.
➢ Take inverse Laplace transform & Convert differential equations in to dot variables (2M)
➢ Apply the state variables to dot variables (2M)
➢ Rearrange the equation and derive state model (3M)
➢ Draw the block diagram for state equation and output equation (5M)

ww
Determine the canonical state model of the system, whose transfer function is

w.E
T(s) = 2(s+5)/(s+1) (s+3) (s+4).
Answer: Page: 6.36-Nagoor kani
BTL4 (13M)

5. asy
➢ Use inspection, cascade, signal flow graph method (1M)
➢ Take inverse Laplace transform & Convert differential equations in to dot variables (2M)

En
➢ Apply the state variables to dot variables (2M)

gin
➢ Rearrange the equation and derive state model (3M)

ee
➢ Draw the block diagram for state equation and output equation (5M)

Compute state transition matrix A = 0 -1.

rin
-2 -3 BTL3
g.n (13M)

6.
Answer: Page: 6.42-Nagoor kani
➢ Find eigen values by using |SI -A |=0 (4M)
➢ Find inverse matrix of |SI -A | (4M)
et
➢ Use partial fraction method to find A, B, C (2M)
➢ Find inverse Laplace of φ(s) to get φ(t) (3M)

Consider the state model given below, verify the system is observable and controllable.
7.
(Apr/May 2015) BTL4 (13M)

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.72

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

Answer: Page: 6.61-Nagoor kani

➢ From the state model identify A, B, C Matrix (2M)
➢ Use Gilberts method or Kalman’s method (2M)
➢ In Gilberts Method Find Ḃ and C. The value of Ḃ does not contain zero value then the
system is completely controllable. The value of C does not contain zero value then the

ww system is completely observable. (5M)

➢ In Kalman’s method Find Qo and Qc. The value of Qo does not contain zero value then

w.E the system is completely controllable. The value of Qo does not contain zero value then
the system is completely observable. (4M)

asy
Test the controllability and observability by using any one method of the given state space
representation model. (Apr/May 2015) BTL4 (13M)

En
gin
8.
Answer: Refer Notes ee rin
➢ From the state model identify A, B, C Matrix (2M)
➢ Use Gilberts method or Kalman’s method (2M) g.n
et
➢ In Gilberts method Find Ḃ and C. The value of Ḃ does not contain zero value then the
system is completely controllable. The value of C does not contain zero value then the
system is completely observable. (5M)
➢ In Kalman’s method Find Qo and Qc. The value of Qo does not contain zero value then
the system is completely controllable. The value of Qo does not contain zero value then
the system is completely observable. (4M)

Consider the following differential equation, obtain the state model in diagonal form.
(nov/dec 2015) BTL 3 (13M)
9.

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.73

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

Answer: Refer Notes

➢ Apply the state variables to dot variables (4M)
➢ Rearrange the equation and derive state model (4M)
➢ Draw the block diagram for state equation and output equation(5M)

Consider the system defined by

ww
w.E
Check controllability and observability. (nov/dec 2015) BTL3 (13M)

10. Answer: Refer Notes

asy
En
➢ From the state model identify A, B, C Matrix (2M)

gin
➢ Use Gilberts method or Kalman’s method (2M)
➢ In Gilberts method Find Ḃ and C. The value of Ḃ does not contain zero value then the

ee
system is completely controllable. The value of C does not contain zero value then the
system is completely observable. (5M)

rin
➢ In Kalman’s method Find Qo and Qc. The value of Qo does not contain zero value then

g.n
the system is completely controllable. The value of Qo does not contain zero value then
the system is completely observable. (4M).

PART * C
et
Test the controllability of the following state model by using both the methods.
(nov/dec 2016) BTL4 (15M)

1.

Answer: Refer Notes

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.74

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

➢ From the state model identify A, B, C Matrix (2M)

➢ Use Gilberts method or Kalman’s method (2M)
➢ In Gilberts method Find Ḃ and C. The value of Ḃ does not contain zero value then the
system is completely controllable. The value of C does not contain zero value then the
system is completely observable. (6M)
➢ In Kalman’s method Find Qo and Qc. The value of Qo does not contain zero value then
the system is completely controllable. The value of Qo does not contain zero value then
the system is completely observable. (5M)
➢ The system is completely observable.

ww
Verify the system is completely controllable and observable. (nov/dec 2016)

w.E
Answer: Refer Notes asy BTL4 (15M)

En
➢ From the state model identify A, B, C Matrix (2M)

gin
2.
➢ Use Gilberts method or Kalman’s method (2M)

ee
➢ In Gilberts method Find Ḃ and C. The value of Ḃ does not contain zero value then the

rin
system is completely controllable. The value of C does not contain zero value then the
system is completely observable. (6M)

g.n
➢ In Kalman’s method Find Qo and Qc. The value of Qo does not contain zero value then
the system is completely controllable. The value of Qo does not contain zero value then
the system is completely observable. (5M)

Check the controllability of the following state model. (nov/dec 2015) et BTL4 (15M)

3.

Answer: Page: 6.51-Nagoor kani

➢ From the state model identify A, B, C Matrix (2M)

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.75

Downloaded From : www.EasyEngineering.net

Downloaded From : www.EasyEngineering.net

REGULATION: 2017 ACADEMIC YEAR: 2018-2019

➢ Use Gilberts method or Kalman’s method (2M)

➢ In Gilberts method Find Ḃ and C. The value of Ḃ does not contain zero value then the
system is completely controllable. The value of C does not contain zero value then the
system is completely observable. (6M)
➢ In Kalman’s method Find Qo and Qc. The value of Qo does not contain zero value then
the system is completely controllable. The value of Qo does not contain zero value then
the system is completely observable. (5M)

ww
w.E
asy
En
gin
ee rin
g.n
et

JIT-JEPPIAAR/EEE/Ms.J.ANGELIN/II YR /SEM / 04/IC 8451/CS/UNIT1-5/QB KEYS/VER 1.0

6.76

Downloaded From : www.EasyEngineering.net