1 Use mason’s gain formula to calculate the transfer function of given figure.

G₁+G₂/1+G₁H

2 Calculate the value of voltage V in the circuit shown below. 45 V

3 What would be the value of impedance of a parallel resonant circuit at antiresonance Resistive and maximum
condition?
4 A power supply with low output impedance has low: Load regulation
5 The format used to present the logic output for the various combinations of logic inputs Truth Table.
to a gate is called a(n):
6 Determine the transfer function Z₂₁ (S) in the circuit 2s
shown below. The transfer function G₂₁ (S) in the
circuit is s/(s+1).

7 A paramagnetic substance is placed in a weak magnetic field and its absolute decreases in proportion
temperature T is increased. As a result, its magnetization: to 1/T
8 Which of the following is an important feature of the sum-of-products form of No signal must pass
expressions? through more than two
gates, not including
inverters.
9 The effect of connecting an additional parallel load to an electrical supply source is to current taken from the
increase the:  source
10 The process of storing the data in the stack is called _______ the stack. pushing into
11 A change in frequency by a factor of ________ is equivalent to 1 octave. 2
12 Determine the dc input resistance looking in at the base of the transistor in the figure 125 kΩ
below. β_DC = 125
13 Find the capacitance of the capacitor 2.53 x 10¯¹¹ pF
required to build an LC oscillator that uses
an inductance of L₁ = 1 mH to produce a
sine wave of frequency 1 GHz.

14 The logic gate that will have HIGH or "1" at its output when any one of its inputs is OR gate
HIGH is a(n):
15 A length L of wire carries a steady current 1 A. It is bent first to form a coil of 1 turn. Four times of its first
The same length is now bent more sharply to give a double loop of smaller radius. The value
magnetic field at the center caused by the same current is:
16 What is the overall transfer function from block diagram reduction for cascaded blocks?  Product of individual
gain
17 The charging time constant of a circuit consisting of an inductor is the time taken for the 37
voltage in the inductor to become __________ % of the initial voltage.
18 In VHDL, how are the statements between BEGIN and END evaluated? Serially
19 By carefully configuring the op-amp external circuit components the op-amp can be All of the choices
made to function as:
20 Which of the following is the Universal Flip-flop? J-K flip-flop
21 The behavior of ferromagnetic domains in an applied magnetic field gives rise to: Hysteresis
22 Which microcontroller is used in Arduino Leonardo? ATmega32u4
23 A voltage waveform V(t) = 12t² is applied across a 1 H inductor for t ≥ 0, with initial 4t³
electric current through it being zero. The electric current through the inductor for t ≥ 0
is given by __________.
24 The tuned collector oscillator circuit used in 1199 kHz
the local oscillator of a radio receiver makes
use of an LC tuned circuit with L₁ = 58.6 µH
and C₁ = 300 pF. Calculate the frequency of
oscillations.

25 What are the components that make the programmable logic controller work? All of the choices
26 If all the poles of H(z) are outside the unit circle, then the system is said to be:  None of the choices

27 A solenoid coil with a resistance of 30 ohms and an inductance of 200 mH is connected 327 W
to a 230 VAC, 50 Hz supply as shown in the figure below. Calculate the average power
consumed by the solenoid.

28 A full wave rectified voltage of 18 Vp is 3.2 %

applied across a 500 µF capacitor filter.
Calculate the ripple if load takes an average
current of 100 mA. Assume supply frequency
50 Hz.
29 Control sequence state is indicated by:  State box
30 Optoelectronics is based on the quantum mechanical effects of light on electronic Yes
materials.
31 Which of the following axial-lead resistor types usually has a blue, light green or red Metal-film resistors.
body?
32 When the number of poles is equal to the number of zeroes, how many branches of root 0
locus tends towards infinity?

33 Which of the following gases are relevant for monitoring in a building system? All of the choices

34 The circuit in the figure shown below uses a: Negative clamper

35 Which of the following is true about microprocessors? It contains ALU, CU and

registers.
36 Determine the critical frequency of the output RC circuit for the FET amplifier in the 46 MHz
figure below.

37 Find the voltage across the inductor in the circuit shown below. Assume the source 17.9/_25.3° V_pp
voltage is 20/_0° peak-to-peak at a frequency of 20 kHz. L is equal to 10 mH, Q_coil is
50, and R₁ is 600 Ω.
38 Calculate the cross-sectional area, in mm², of 3.2 mm²
a piece of copper wire, 40 m in length and
having a resistance of 0.25 Ω. Take the
resistivity of copper as 0.02 x 10¯⁶ Ω -m.

39 What type of register would shift a complete binary number in one bit at a time and shift SISO
all the stored bits out one bit at a time?

40 What stage in which the CPU fetches the instructions from the instruction cache in Prefetch stage
superscalar organization? 

41 A network contains linear resistors and ideal voltage source s. If values of all the remains same
resistors are doubled, then voltage across each resistor is __________.

42 The Static Induction Thyristor (SITH) is a: 3 terminal, self-

controlled device
43 Current stability of a CC amplifier can be increased by: Increasing emitter
resistance and decreasing
base resistance
44 The threshold voltage of an n-channel MOSFET can be increased by: Reducing the channel
dopant concentration.
45 The drain current in JFET is controlled by: Reverse-bias at the gate

46 What measure the relative level of moisture in the air, and are important in critical Humidity sensors
environments like libraries, labs and data centers? 
47 A typical data acquisition system consists of __________. sensors
48 The instruction, “INC” increases the contents of the specified register or memory 1
location by: 
49 Which of the following circuits is commonly used to provide transient protection? A clipper
50 What is the disadvantage of machine level programming?  All of the choices
51 If an ac signal generator drives a series RLC circuit, then the current undergoes supply frequency
resonance only due to variation in _____.

52 Experimenter A uses a test charge-2q₀ to measure an electric field produced by the same in both
stationary charges. A finds a field that is: magnitude and direction
as the field found by B
53 When two storage elements are present in a circuit, its equation is:  2nd order
54 Which among the following varies in both magnitude and sign over a cycle? Instantaneous power
55 Which of the following is not a data copy/transfer instruction? DAS

56 Operation code field is present in: machine language

instruction

57 Which one of the following applications software’s is used to obtain an accurate root MATLAB
locus?
58 For the typical characteristics of the 741 op-amp with r₀ = 75 Ω and A = 200 k Ω, 0.011 Ω
calculate Z₀ if R_f  = 360 k Ω and R₁ = 12 k Ω.

Solution:

59 The figure shown below is a circuit diagram of ___________ amplifier? Cascade amplifier

60 For a good, stabilized biasing of the transistor of the CE amplifier of figure. We should R_E/R_B >> 1
have:

61 Which of the following is known as the Maxwell’s first equation in free space?  ▽×H = D

62 What equation represents the time varying electric field?  E = ▽V – A

63 Which of the following technology was used by Intel to design its first 8-bit PMOS
microprocessor?
64 Determine the impedance of the 162.6/_-84.8°
network shown in the figure
below at a frequency of 10 kHz.
65 Find the value of the currents I₁ and I₂ flowing clockwise in the first and second mesh 0.96A, -1.73A
respectively.

66 The feedback circuit connection shown in the figure below is: Voltage series feedback

67 Asynchronous circuits are useful in application where the input signals may: Both change at any time
and never change
68 A transistor with β = 120 is biased to operate at a dc collector current of 1.2 mA. Find 20.6 ohms
the value of r_e.

69 In the circuit given below, the value of R_L for maximum power transfer is 2.8 Ω
___________.

70 A process is moved to wait queue when I/O request is made with ____________. blocking I/O
71 Which of the following circuits is used to change the dc reference of a signal without A clamper
changing the shape of the signal?
72 A proton (charge e), traveling perpendicular to a magnetic field, experiences the same 2
force as an alpha particle (charge 2e) which is also traveling perpendicular to the same
field. The ratio of their speeds V_proton/V_alpha, is:

73 Which of the low-frequency cutoffs determined by C_S, C_C, or C_E will be the highest
predominant factor in determining the low-frequency response for the complete system?

74 The ________ directive instructs the assembler to begin memory allocation for a ORG
segment/block/code from the stated address.

75 Which of the following is modified by the second derivative input signals? The time constant and
suppress the oscillations.
76 If a 90 GB memory has to be connected to a microprocessor, minimum how many 37
address lines are required?

77 Find the value of the currents I₁, I₂ and I₃ 1.54 A, -0.189 A, -1.195 A
flowing clockwise in the first, second and third
mesh respectively.

78 For the low-frequency response of a BJT amplifier, the maximum gain is where R_E = 0 Ω
_______.
79 A JFET cascade amplifier employs 1 common-gate and 1
common-source
amplifier.
80 A logic probe is placed on the output of a gate and the display indicator is dim. A pulser The output of the gate
is used on each of the input terminals, but the output indication does not change. What is appears to be open.
wrong?
81 Determine how much the Q-point (I_C, 18.6 % and 15.1%
V_CE) for the circuit in the figure
below will change over the temperature
range B_DC increases from 85 to 100
and V_BE decreases form 0.7 V to 0.6
V.

82 What is the unit step response of the system described by the difference equation? [1.099+1.088(0.9)ⁿ.cos((π/
3)n−5.2°)]u(n)
  y(n)=0.9y(n-1)-0.81y(n-2)+x(n) under the initial conditions y(-1)=y(-2)=0?

Solution:
83 Which of the following combinations cannot be combined into K-map groups? Diagonal corners
84 A band pass active filter connection using an operational amplifier will provide a From f₀₁ to f_oh
constant output:
85 What do you call the ratio of voltage transform at the first port to the current transform Transfer impedance
at the second port?

86 On which of the following factors does the sensitivity of a closed loop system to gain All of the choices
changes and load disturbances depend?
87 Which of the following is the correct sequence of operations in a microprocessor? Opcode fetch, memory
read, memory write, I/O
read, I/O write
88 The Q of a crystal is typically ______. 20,000

89 Calculate the mesh currents. 2A, 1A, 0.57A

90 What do you call the ratio of voltage transform at first port to the voltage transform at Voltage transfer ratio
the second port? 
91 Which one of the following is a method for designing finite state machines? ASM block
92 A ripple counter’s speed is limited by the propagation delay of: each flip-flop

93 Transient response analysis is done for _________ systems. stable

94 What device from the thyristor family has its gate terminal connected to the n-type PUT
material near the anode? 
95 From the circuit shown below, determine the impedance. Given: R = 250 Ω; L = 1.20 1495 Ω
mH; C = 1.80 µF; V_p =120 V and f = 60 Hz.

96 According to the principle of current mirror, if gate-source potentials of two identical Equal
MOS transistors are equal, then the channel currents should be:
97 A copper wire has a resistance of 200 252 Ω
Ω at 20°C. A current is passed through
the wire and the temperature rises to
90°C. Determine the resistance of the
wire at 90°C, correct to the nearest
ohm, assuming that the temperature
coefficient of resistance is 0.004/°C at
0°C

98 What is the name of the device that allows four surveillance camera images to be A quad switcher
viewed on a monitor at the same time?

99 Coefficients which have the dimensions of admittance are called: Y-parameters

100 Which of the following is NOT a major component of a sequential logic system. XOR gates.