Scribd
Upload
3K views

Autodesk Robot Structural Analysis Professional 2011 - Note

This document summarizes the design of a spread footing foundation. It includes the geometry, materials, loads, and geotechnical design calculations for the foundation. The geotechnical design checks capacity, rotation, sliding, uplift, and settlement. It also includes the reinforced concrete design, with analysis of punching shear, required reinforcement, and provided reinforcement details. Survey information is also provided on the concrete volume, formwork, rebar quantities and sizes.

Uploaded by

01oscar1977
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
3K views

Autodesk Robot Structural Analysis Professional 2011 - Note

This document summarizes the design of a spread footing foundation. It includes the geometry, materials, loads, and geotechnical design calculations for the foundation. The geotechnical design checks capacity, rotation, sliding, uplift, and settlement. It also includes the reinforced concrete design, with analysis of punching shear, required reinforcement, and provided reinforcement details. Survey information is also provided on the concrete volume, formwork, rebar quantities and sizes.

Uploaded by

01oscar1977
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

Autodesk Robot Structural Analysis Professional 2011 Author: Address:

File: Structure.rtd Project: Structure

1
1.1

Spread footing: Foundation1


Basic data
Assumptions Geotechnic calculations according to Concrete calculations according to Shape selection 1.1.2 Geometry: : BS 8004 : BS 8110 : without limits

Number: 1

1.1.1

A B h1 h2 h4

= 2.20 (m) = 2.20 (m) = 0.40 (m) = 0.00 (m) = 0.10 (m)

a b ex ey

= 0.45 (m) = 0.45 (m) = 0.00 (m) = 0.00 (m)

a' b' c1 c2 1.1.3

= 450 (mm) = 450 (mm) = 50 (mm) = 50 (mm)

Materials Concrete Longitudinal reinforcement 460.00 MPa Transversal reinforcement 250.00 MPa : C20; Characteristic strength = 21.00 MPa Unit weight = 2501.36 (kG/m3) : type T Characteristic strength = : type R Characteristic strength =

1.1.4

Loads: Foundation loads:


Case DL1 Nature dead load Group 1 N (kN) 785.71 Fx (kN) 0.00 Fy (kN) 0.00 Mx (kN*m) 0.00 My (kN*m) 0.00

Backfill loads:
Case Nature Q1 (kN/m2)

Date : 19/03/09

Page : 1

This page was created using NitroPDF trial software. To purchase, go to http://www.nitropdf.com/

Autodesk Robot Structural Analysis Professional 2011 Author: Address:

File: Structure.rtd Project: Structure

1.1.5

Combination list
1/ 2/* 3/* 4/* SLS : 1.00DL1 ULS : 1.40DL1 ULS : 1.00DL1 SLS : 1.00DL1

1.2
1.2.1

Geotechnical design
Assumptions Foundation design for: Capacity Rotation Sliding Sliding with soil pressure considered: Uplift Average settlement

for X and Y directions

1.2.2

Soil: Soil level: Column pier level: Minimum reference level: N1 Na Nf = 1.00 (m) = 0.00 (m) = -0.50 (m)

well graded gravels Soil level: 1.00 (m) Unit weight:2243.38 (kG/m3) Unit weight of solid: 2702.25 (kG/m3) Internal friction angle: 35.0 (Deg) Cohesion: 0.00 (MPa) 1.2.3 Limit states Stress calculations Soil type under foundation: not layered SLS : 1.00DL1 Design combination Load factors: 1.00 * Foundation weight 1.00 * Soil weight Calculation results: On the foundation level Weight of foundation and soil over it: Gr = 149.52 (kN) Design load: Nr = 935.23 (kN) Mx = -0.00 (kN*m) My = 0.00 (kN*m) Soil profile parameters: C = 0.00 (MPa) = 0.00 = 0.00 (kG/m3) Stress in soil: 0.19 (MPa) Design soil pressure 0.20 (MPa) Safety factor: 1.035 > 1 Uplift Uplift in SLS
Date : 19/03/09 Page : 2

This page was created using NitroPDF trial software. To purchase, go to http://www.nitropdf.com/

Autodesk Robot Structural Analysis Professional 2011 Author: Address:

File: Structure.rtd Project: Structure

Design combination: Load factors: Contact area:

SLS : 1.00DL1 1.00 * Foundation weight 1.00 * Soil weight s = 4.89 slim = 1.00

Sliding Design combination Load factors: SLS : 1.00DL1 1.00 * Foundation weight 1.00 * Soil weight Weight of foundation and soil over it: Gr = 149.52 (kN) Design load: Nr = 935.23 (kN) Mx = -0.00 (kN*m) My = 0.00 (kN*m) Equivalent foundation dimensions: A_ = 2.20 (m)B_ = 2.20 (m) Sliding area: 4.84 (m2) Foundation/soil friction coefficient: tg( = 0.70 Cohesion: C = 0.00 (MPa) Soil pressure considered: Hx = 0.00 (kN) Hy = 0.00 (kN) Ppx = 0.00 (kN) Ppy = 0.00 (kN) Pax = 0.00 (kN) Pay = 0.00 (kN) Sliding force value F = 0.00 (kN) Value of force preventing foundation sliding: - On the foundation level: F(stab) = 654.85 (kN) Stabilility for sliding:

Average settlement Soil type under foundation: not layered SLS : 1.00DL1 Design combination Load factors: 1.00 * Foundation weight 1.00 * Soil weight Weight of foundation and soil over it: Gr = 149.52 (kN) Average stress caused by design load: q = 0.19 (MPa) Thickness of the actively settling soil: z = 4.40 (m) Stress on the level z: - Additional: zd = 0.02 (MPa) z = 0.13 (MPa) - Caused by soil weight: Settlement: - Original s' = 1 (mm) - Secondary s'' = 0 (mm) - TOTAL S = 1 (mm) < Sadm = 50 (mm) Safety factor: 39.02 > 1 Settlement difference Design combination Load factors: Settlement difference: Safety factor: Rotation About OX axis Design combination SLS : 1.00DL1 SLS : 1.00DL1 1.00 * Foundation weight 1.00 * Soil weight S = 0 (mm) < Sadm = 50 (mm)

Date : 19/03/09

Page : 3

This page was created using NitroPDF trial software. To purchase, go to http://www.nitropdf.com/

Autodesk Robot Structural Analysis Professional 2011 Author: Address:

File: Structure.rtd Project: Structure

1.00 * Foundation weight 1.00 * Soil weight Weight of foundation and soil over it: Gr = 149.52 (kN) Design load: Nr = 935.23 (kN) Mx = -0.00 (kN*m) My = 0.00 (kN*m) Stability moment: Mstab = 1028.75 (kN*m) Rotation moment: Mrenv = 0.00 (kN*m) Stability for rotation: About OY axis Design combination: Load factors:

Load factors:

SLS : 1.00DL1 1.00 * Foundation weight 1.00 * Soil weight Weight of foundation and soil over it: Gr = 149.52 (kN) Design load: Nr = 935.23 (kN) Mx = -0.00 (kN*m) My = 0.00 (kN*m) Stability moment: Mstab = 1028.75 (kN*m) Rotation moment: Mrenv = 0.00 (kN*m) Stability for rotation:

1.3

RC design
Assumptions Exposure : mild

1.3.1

1.3.2

Analysis of punching and shear Shear Design combination Load factors: ULS : 1.40DL1 1.00 * Foundation weight 1.00 * Soil weight

Design load: Nr = 1249.52 (kN) Mx = -0.00 (kN*m) My = 0.00 (kN*m) Length of critical circumference: 2.20 (m) Shear force: 266.42 (kN) Section effective height heff = 0.34 (m) Shear area: A = 0.75 (m2) = 0.18 % Reinforcement ratio: Shear stress: 0.36 (MPa) Admissible shear stress: 0.37 (MPa) Safety factor: 1.044 > 1 1.3.3 Required reinforcement Spread footing: bottom: ULS : 1.40DL1 My = 190.63 (kN*m) ULS : 1.40DL1
Date : 19/03/09 Page : 4

Asx = 612 (mm2/m)

This page was created using NitroPDF trial software. To purchase, go to http://www.nitropdf.com/

Autodesk Robot Structural Analysis Professional 2011 Author: Address:

File: Structure.rtd Project: Structure

Mx = 190.63 (kN*m)

Asy = 612 (mm2/m) As min = 520 (mm2/m)

top:

A'sx = 0 (mm2/m) A'sy = 0 (mm2/m) As min = 0 (mm2/m) A min. = 0 (mm2)

Column pier: Longitudinal reinforcement A Asx

A = 0 (mm2) = 2 * (Asx + Asy) = 0 (mm2) Asy

= 0 (mm2)

1.3.4

Provided reinforcement 2.3.1 Spread footing: Bottom: Along X axis: Along Y axis: Top:
7 T 16 7 T 16 l = 2.10 (m) l = 2.10 (m) e = 1*-1.05 e = 0.32

2.3.2 Pier Longitudinal reinforcement

Transversal reinforcement
3 R6 l = 1.43 (m) e = 1*0.18

Material survey:
Concrete volume Formwork = 1.94 (m3) = 3.52 (m2)

Steel T Total weight = 46.42 (kG) Density = 23.98 (kG/m3) Average diameter = 16.0 (mm) Survey according to diameters: Diameter 16 Steel R Total weight
Date : 19/03/09

Length (m) 2.10

Number: 14

= 4.16 (kG)
Page : 5

This page was created using NitroPDF trial software. To purchase, go to http://www.nitropdf.com/

Autodesk Robot Structural Analysis Professional 2011 Author: Address:

File: Structure.rtd Project: Structure

Density = 2.15 (kG/m3) Average diameter = 8.7 (mm) Survey according to diameters: Diameter 6 12 Length (m) 1.43 0.90 Number: 3 4

Date : 19/03/09

Page : 6

This page was created using NitroPDF trial software. To purchase, go to http://www.nitropdf.com/

You might also like